1 // SPDX-License-Identifier: GPL-2.0-only 2 /* 3 * gpio-max3191x.c - GPIO driver for Maxim MAX3191x industrial serializer 4 * 5 * Copyright (C) 2017 KUNBUS GmbH 6 * 7 * The MAX3191x makes 8 digital 24V inputs available via SPI. 8 * Multiple chips can be daisy-chained, the spec does not impose 9 * a limit on the number of chips and neither does this driver. 10 * 11 * Either of two modes is selectable: In 8-bit mode, only the state 12 * of the inputs is clocked out to achieve high readout speeds; 13 * In 16-bit mode, an additional status byte is clocked out with 14 * a CRC and indicator bits for undervoltage and overtemperature. 15 * The driver returns an error instead of potentially bogus data 16 * if any of these fault conditions occur. However it does allow 17 * readout of non-faulting chips in the same daisy-chain. 18 * 19 * MAX3191x supports four debounce settings and the driver is 20 * capable of configuring these differently for each chip in the 21 * daisy-chain. 22 * 23 * If the chips are hardwired to 8-bit mode ("modesel" pulled high), 24 * gpio-pisosr.c can be used alternatively to this driver. 25 * 26 * https://datasheets.maximintegrated.com/en/ds/MAX31910.pdf 27 * https://datasheets.maximintegrated.com/en/ds/MAX31911.pdf 28 * https://datasheets.maximintegrated.com/en/ds/MAX31912.pdf 29 * https://datasheets.maximintegrated.com/en/ds/MAX31913.pdf 30 * https://datasheets.maximintegrated.com/en/ds/MAX31953-MAX31963.pdf 31 */ 32 33 #include <linux/bitmap.h> 34 #include <linux/bitops.h> 35 #include <linux/crc8.h> 36 #include <linux/gpio/consumer.h> 37 #include <linux/gpio/driver.h> 38 #include <linux/module.h> 39 #include <linux/spi/spi.h> 40 41 enum max3191x_mode { 42 STATUS_BYTE_ENABLED, 43 STATUS_BYTE_DISABLED, 44 }; 45 46 /** 47 * struct max3191x_chip - max3191x daisy-chain 48 * @gpio: GPIO controller struct 49 * @lock: protects read sequences 50 * @nchips: number of chips in the daisy-chain 51 * @mode: current mode, 0 for 16-bit, 1 for 8-bit; 52 * for simplicity, all chips in the daisy-chain are assumed 53 * to use the same mode 54 * @modesel_pins: GPIO pins to configure modesel of each chip 55 * @fault_pins: GPIO pins to detect fault of each chip 56 * @db0_pins: GPIO pins to configure debounce of each chip 57 * @db1_pins: GPIO pins to configure debounce of each chip 58 * @mesg: SPI message to perform a readout 59 * @xfer: SPI transfer used by @mesg 60 * @crc_error: bitmap signaling CRC error for each chip 61 * @overtemp: bitmap signaling overtemperature alarm for each chip 62 * @undervolt1: bitmap signaling undervoltage alarm for each chip 63 * @undervolt2: bitmap signaling undervoltage warning for each chip 64 * @fault: bitmap signaling assertion of @fault_pins for each chip 65 * @ignore_uv: whether to ignore undervoltage alarms; 66 * set by a device property if the chips are powered through 67 * 5VOUT instead of VCC24V, in which case they will constantly 68 * signal undervoltage; 69 * for simplicity, all chips in the daisy-chain are assumed 70 * to be powered the same way 71 */ 72 struct max3191x_chip { 73 struct gpio_chip gpio; 74 struct mutex lock; 75 u32 nchips; 76 enum max3191x_mode mode; 77 struct gpio_descs *modesel_pins; 78 struct gpio_descs *fault_pins; 79 struct gpio_descs *db0_pins; 80 struct gpio_descs *db1_pins; 81 struct spi_message mesg; 82 struct spi_transfer xfer; 83 unsigned long *crc_error; 84 unsigned long *overtemp; 85 unsigned long *undervolt1; 86 unsigned long *undervolt2; 87 unsigned long *fault; 88 bool ignore_uv; 89 }; 90 91 #define MAX3191X_NGPIO 8 92 #define MAX3191X_CRC8_POLYNOMIAL 0xa8 /* (x^5) + x^4 + x^2 + x^0 */ 93 94 DECLARE_CRC8_TABLE(max3191x_crc8); 95 96 static int max3191x_get_direction(struct gpio_chip *gpio, unsigned int offset) 97 { 98 return GPIO_LINE_DIRECTION_IN; /* always in */ 99 } 100 101 static int max3191x_direction_input(struct gpio_chip *gpio, unsigned int offset) 102 { 103 return 0; 104 } 105 106 static int max3191x_direction_output(struct gpio_chip *gpio, 107 unsigned int offset, int value) 108 { 109 return -EINVAL; 110 } 111 112 static void max3191x_set(struct gpio_chip *gpio, unsigned int offset, int value) 113 { } 114 115 static void max3191x_set_multiple(struct gpio_chip *gpio, unsigned long *mask, 116 unsigned long *bits) 117 { } 118 119 static unsigned int max3191x_wordlen(struct max3191x_chip *max3191x) 120 { 121 return max3191x->mode == STATUS_BYTE_ENABLED ? 2 : 1; 122 } 123 124 static int max3191x_readout_locked(struct max3191x_chip *max3191x) 125 { 126 struct device *dev = max3191x->gpio.parent; 127 struct spi_device *spi = to_spi_device(dev); 128 int val, i, ot = 0, uv1 = 0; 129 130 val = spi_sync(spi, &max3191x->mesg); 131 if (val) { 132 dev_err_ratelimited(dev, "SPI receive error %d\n", val); 133 return val; 134 } 135 136 for (i = 0; i < max3191x->nchips; i++) { 137 if (max3191x->mode == STATUS_BYTE_ENABLED) { 138 u8 in = ((u8 *)max3191x->xfer.rx_buf)[i * 2]; 139 u8 status = ((u8 *)max3191x->xfer.rx_buf)[i * 2 + 1]; 140 141 val = (status & 0xf8) != crc8(max3191x_crc8, &in, 1, 0); 142 __assign_bit(i, max3191x->crc_error, val); 143 if (val) 144 dev_err_ratelimited(dev, 145 "chip %d: CRC error\n", i); 146 147 ot = (status >> 1) & 1; 148 __assign_bit(i, max3191x->overtemp, ot); 149 if (ot) 150 dev_err_ratelimited(dev, 151 "chip %d: overtemperature\n", i); 152 153 if (!max3191x->ignore_uv) { 154 uv1 = !((status >> 2) & 1); 155 __assign_bit(i, max3191x->undervolt1, uv1); 156 if (uv1) 157 dev_err_ratelimited(dev, 158 "chip %d: undervoltage\n", i); 159 160 val = !(status & 1); 161 __assign_bit(i, max3191x->undervolt2, val); 162 if (val && !uv1) 163 dev_warn_ratelimited(dev, 164 "chip %d: voltage warn\n", i); 165 } 166 } 167 168 if (max3191x->fault_pins && !max3191x->ignore_uv) { 169 /* fault pin shared by all chips or per chip */ 170 struct gpio_desc *fault_pin = 171 (max3191x->fault_pins->ndescs == 1) 172 ? max3191x->fault_pins->desc[0] 173 : max3191x->fault_pins->desc[i]; 174 175 val = gpiod_get_value_cansleep(fault_pin); 176 if (val < 0) { 177 dev_err_ratelimited(dev, 178 "GPIO read error %d\n", val); 179 return val; 180 } 181 __assign_bit(i, max3191x->fault, val); 182 if (val && !uv1 && !ot) 183 dev_err_ratelimited(dev, 184 "chip %d: fault\n", i); 185 } 186 } 187 188 return 0; 189 } 190 191 static bool max3191x_chip_is_faulting(struct max3191x_chip *max3191x, 192 unsigned int chipnum) 193 { 194 /* without status byte the only diagnostic is the fault pin */ 195 if (!max3191x->ignore_uv && test_bit(chipnum, max3191x->fault)) 196 return true; 197 198 if (max3191x->mode == STATUS_BYTE_DISABLED) 199 return false; 200 201 return test_bit(chipnum, max3191x->crc_error) || 202 test_bit(chipnum, max3191x->overtemp) || 203 (!max3191x->ignore_uv && 204 test_bit(chipnum, max3191x->undervolt1)); 205 } 206 207 static int max3191x_get(struct gpio_chip *gpio, unsigned int offset) 208 { 209 struct max3191x_chip *max3191x = gpiochip_get_data(gpio); 210 int ret, chipnum, wordlen = max3191x_wordlen(max3191x); 211 u8 in; 212 213 mutex_lock(&max3191x->lock); 214 ret = max3191x_readout_locked(max3191x); 215 if (ret) 216 goto out_unlock; 217 218 chipnum = offset / MAX3191X_NGPIO; 219 if (max3191x_chip_is_faulting(max3191x, chipnum)) { 220 ret = -EIO; 221 goto out_unlock; 222 } 223 224 in = ((u8 *)max3191x->xfer.rx_buf)[chipnum * wordlen]; 225 ret = (in >> (offset % MAX3191X_NGPIO)) & 1; 226 227 out_unlock: 228 mutex_unlock(&max3191x->lock); 229 return ret; 230 } 231 232 static int max3191x_get_multiple(struct gpio_chip *gpio, unsigned long *mask, 233 unsigned long *bits) 234 { 235 struct max3191x_chip *max3191x = gpiochip_get_data(gpio); 236 const unsigned int wordlen = max3191x_wordlen(max3191x); 237 int ret; 238 unsigned long bit; 239 unsigned long gpio_mask; 240 unsigned long in; 241 242 mutex_lock(&max3191x->lock); 243 ret = max3191x_readout_locked(max3191x); 244 if (ret) 245 goto out_unlock; 246 247 bitmap_zero(bits, gpio->ngpio); 248 for_each_set_clump8(bit, gpio_mask, mask, gpio->ngpio) { 249 unsigned int chipnum = bit / MAX3191X_NGPIO; 250 251 if (max3191x_chip_is_faulting(max3191x, chipnum)) { 252 ret = -EIO; 253 goto out_unlock; 254 } 255 256 in = ((u8 *)max3191x->xfer.rx_buf)[chipnum * wordlen]; 257 in &= gpio_mask; 258 bitmap_set_value8(bits, in, bit); 259 } 260 261 out_unlock: 262 mutex_unlock(&max3191x->lock); 263 return ret; 264 } 265 266 static int max3191x_set_config(struct gpio_chip *gpio, unsigned int offset, 267 unsigned long config) 268 { 269 struct max3191x_chip *max3191x = gpiochip_get_data(gpio); 270 u32 debounce, chipnum, db0_val, db1_val; 271 272 if (pinconf_to_config_param(config) != PIN_CONFIG_INPUT_DEBOUNCE) 273 return -ENOTSUPP; 274 275 if (!max3191x->db0_pins || !max3191x->db1_pins) 276 return -EINVAL; 277 278 debounce = pinconf_to_config_argument(config); 279 switch (debounce) { 280 case 0: 281 db0_val = 0; 282 db1_val = 0; 283 break; 284 case 1 ... 25: 285 db0_val = 0; 286 db1_val = 1; 287 break; 288 case 26 ... 750: 289 db0_val = 1; 290 db1_val = 0; 291 break; 292 case 751 ... 3000: 293 db0_val = 1; 294 db1_val = 1; 295 break; 296 default: 297 return -EINVAL; 298 } 299 300 if (max3191x->db0_pins->ndescs == 1) 301 chipnum = 0; /* all chips use the same pair of debounce pins */ 302 else 303 chipnum = offset / MAX3191X_NGPIO; /* per chip debounce pins */ 304 305 mutex_lock(&max3191x->lock); 306 gpiod_set_value_cansleep(max3191x->db0_pins->desc[chipnum], db0_val); 307 gpiod_set_value_cansleep(max3191x->db1_pins->desc[chipnum], db1_val); 308 mutex_unlock(&max3191x->lock); 309 return 0; 310 } 311 312 static void gpiod_set_array_single_value_cansleep(unsigned int ndescs, 313 struct gpio_desc **desc, 314 struct gpio_array *info, 315 int value) 316 { 317 unsigned long *values; 318 319 values = bitmap_alloc(ndescs, GFP_KERNEL); 320 if (!values) 321 return; 322 323 if (value) 324 bitmap_fill(values, ndescs); 325 else 326 bitmap_zero(values, ndescs); 327 328 gpiod_set_array_value_cansleep(ndescs, desc, info, values); 329 bitmap_free(values); 330 } 331 332 static struct gpio_descs *devm_gpiod_get_array_optional_count( 333 struct device *dev, const char *con_id, 334 enum gpiod_flags flags, unsigned int expected) 335 { 336 struct gpio_descs *descs; 337 int found = gpiod_count(dev, con_id); 338 339 if (found == -ENOENT) 340 return NULL; 341 342 if (found != expected && found != 1) { 343 dev_err(dev, "ignoring %s-gpios: found %d, expected %u or 1\n", 344 con_id, found, expected); 345 return NULL; 346 } 347 348 descs = devm_gpiod_get_array_optional(dev, con_id, flags); 349 350 if (IS_ERR(descs)) { 351 dev_err(dev, "failed to get %s-gpios: %ld\n", 352 con_id, PTR_ERR(descs)); 353 return NULL; 354 } 355 356 return descs; 357 } 358 359 static int max3191x_probe(struct spi_device *spi) 360 { 361 struct device *dev = &spi->dev; 362 struct max3191x_chip *max3191x; 363 int n, ret; 364 365 max3191x = devm_kzalloc(dev, sizeof(*max3191x), GFP_KERNEL); 366 if (!max3191x) 367 return -ENOMEM; 368 spi_set_drvdata(spi, max3191x); 369 370 max3191x->nchips = 1; 371 device_property_read_u32(dev, "#daisy-chained-devices", 372 &max3191x->nchips); 373 374 n = BITS_TO_LONGS(max3191x->nchips); 375 max3191x->crc_error = devm_kcalloc(dev, n, sizeof(long), GFP_KERNEL); 376 max3191x->undervolt1 = devm_kcalloc(dev, n, sizeof(long), GFP_KERNEL); 377 max3191x->undervolt2 = devm_kcalloc(dev, n, sizeof(long), GFP_KERNEL); 378 max3191x->overtemp = devm_kcalloc(dev, n, sizeof(long), GFP_KERNEL); 379 max3191x->fault = devm_kcalloc(dev, n, sizeof(long), GFP_KERNEL); 380 max3191x->xfer.rx_buf = devm_kcalloc(dev, max3191x->nchips, 381 2, GFP_KERNEL); 382 if (!max3191x->crc_error || !max3191x->undervolt1 || 383 !max3191x->overtemp || !max3191x->undervolt2 || 384 !max3191x->fault || !max3191x->xfer.rx_buf) 385 return -ENOMEM; 386 387 max3191x->modesel_pins = devm_gpiod_get_array_optional_count(dev, 388 "maxim,modesel", GPIOD_ASIS, max3191x->nchips); 389 max3191x->fault_pins = devm_gpiod_get_array_optional_count(dev, 390 "maxim,fault", GPIOD_IN, max3191x->nchips); 391 max3191x->db0_pins = devm_gpiod_get_array_optional_count(dev, 392 "maxim,db0", GPIOD_OUT_LOW, max3191x->nchips); 393 max3191x->db1_pins = devm_gpiod_get_array_optional_count(dev, 394 "maxim,db1", GPIOD_OUT_LOW, max3191x->nchips); 395 396 max3191x->mode = device_property_read_bool(dev, "maxim,modesel-8bit") 397 ? STATUS_BYTE_DISABLED : STATUS_BYTE_ENABLED; 398 if (max3191x->modesel_pins) 399 gpiod_set_array_single_value_cansleep( 400 max3191x->modesel_pins->ndescs, 401 max3191x->modesel_pins->desc, 402 max3191x->modesel_pins->info, max3191x->mode); 403 404 max3191x->ignore_uv = device_property_read_bool(dev, 405 "maxim,ignore-undervoltage"); 406 407 if (max3191x->db0_pins && max3191x->db1_pins && 408 max3191x->db0_pins->ndescs != max3191x->db1_pins->ndescs) { 409 dev_err(dev, "ignoring maxim,db*-gpios: array len mismatch\n"); 410 devm_gpiod_put_array(dev, max3191x->db0_pins); 411 devm_gpiod_put_array(dev, max3191x->db1_pins); 412 max3191x->db0_pins = NULL; 413 max3191x->db1_pins = NULL; 414 } 415 416 max3191x->xfer.len = max3191x->nchips * max3191x_wordlen(max3191x); 417 spi_message_init_with_transfers(&max3191x->mesg, &max3191x->xfer, 1); 418 419 max3191x->gpio.label = spi->modalias; 420 max3191x->gpio.owner = THIS_MODULE; 421 max3191x->gpio.parent = dev; 422 max3191x->gpio.base = -1; 423 max3191x->gpio.ngpio = max3191x->nchips * MAX3191X_NGPIO; 424 max3191x->gpio.can_sleep = true; 425 426 max3191x->gpio.get_direction = max3191x_get_direction; 427 max3191x->gpio.direction_input = max3191x_direction_input; 428 max3191x->gpio.direction_output = max3191x_direction_output; 429 max3191x->gpio.set = max3191x_set; 430 max3191x->gpio.set_multiple = max3191x_set_multiple; 431 max3191x->gpio.get = max3191x_get; 432 max3191x->gpio.get_multiple = max3191x_get_multiple; 433 max3191x->gpio.set_config = max3191x_set_config; 434 435 mutex_init(&max3191x->lock); 436 437 ret = gpiochip_add_data(&max3191x->gpio, max3191x); 438 if (ret) { 439 mutex_destroy(&max3191x->lock); 440 return ret; 441 } 442 443 return 0; 444 } 445 446 static void max3191x_remove(struct spi_device *spi) 447 { 448 struct max3191x_chip *max3191x = spi_get_drvdata(spi); 449 450 gpiochip_remove(&max3191x->gpio); 451 mutex_destroy(&max3191x->lock); 452 } 453 454 static int __init max3191x_register_driver(struct spi_driver *sdrv) 455 { 456 crc8_populate_msb(max3191x_crc8, MAX3191X_CRC8_POLYNOMIAL); 457 return spi_register_driver(sdrv); 458 } 459 460 static const struct of_device_id max3191x_of_id[] = { 461 { .compatible = "maxim,max31910" }, 462 { .compatible = "maxim,max31911" }, 463 { .compatible = "maxim,max31912" }, 464 { .compatible = "maxim,max31913" }, 465 { .compatible = "maxim,max31953" }, 466 { .compatible = "maxim,max31963" }, 467 { } 468 }; 469 MODULE_DEVICE_TABLE(of, max3191x_of_id); 470 471 static const struct spi_device_id max3191x_spi_id[] = { 472 { "max31910" }, 473 { "max31911" }, 474 { "max31912" }, 475 { "max31913" }, 476 { "max31953" }, 477 { "max31963" }, 478 { } 479 }; 480 MODULE_DEVICE_TABLE(spi, max3191x_spi_id); 481 482 static struct spi_driver max3191x_driver = { 483 .driver = { 484 .name = "max3191x", 485 .of_match_table = max3191x_of_id, 486 }, 487 .probe = max3191x_probe, 488 .remove = max3191x_remove, 489 .id_table = max3191x_spi_id, 490 }; 491 module_driver(max3191x_driver, max3191x_register_driver, spi_unregister_driver); 492 493 MODULE_AUTHOR("Lukas Wunner <lukas@wunner.de>"); 494 MODULE_DESCRIPTION("GPIO driver for Maxim MAX3191x industrial serializer"); 495 MODULE_LICENSE("GPL v2"); 496