1# SPDX-License-Identifier: GPL-2.0-only 2# 3# For a description of the syntax of this configuration file, 4# see Documentation/kbuild/kconfig-language.rst. 5# 6 7menu "Firmware Drivers" 8 9source "drivers/firmware/arm_scmi/Kconfig" 10 11config ARM_SCPI_PROTOCOL 12 tristate "ARM System Control and Power Interface (SCPI) Message Protocol" 13 depends on ARM || ARM64 || COMPILE_TEST 14 depends on MAILBOX 15 help 16 System Control and Power Interface (SCPI) Message Protocol is 17 defined for the purpose of communication between the Application 18 Cores(AP) and the System Control Processor(SCP). The MHU peripheral 19 provides a mechanism for inter-processor communication between SCP 20 and AP. 21 22 SCP controls most of the power management on the Application 23 Processors. It offers control and management of: the core/cluster 24 power states, various power domain DVFS including the core/cluster, 25 certain system clocks configuration, thermal sensors and many 26 others. 27 28 This protocol library provides interface for all the client drivers 29 making use of the features offered by the SCP. 30 31config ARM_SCPI_POWER_DOMAIN 32 tristate "SCPI power domain driver" 33 depends on ARM_SCPI_PROTOCOL || (COMPILE_TEST && OF) 34 default y 35 select PM_GENERIC_DOMAINS if PM 36 help 37 This enables support for the SCPI power domains which can be 38 enabled or disabled via the SCP firmware 39 40config ARM_SDE_INTERFACE 41 bool "ARM Software Delegated Exception Interface (SDEI)" 42 depends on ARM64 43 depends on ACPI_APEI_GHES 44 help 45 The Software Delegated Exception Interface (SDEI) is an ARM 46 standard for registering callbacks from the platform firmware 47 into the OS. This is typically used to implement RAS notifications. 48 49config EDD 50 tristate "BIOS Enhanced Disk Drive calls determine boot disk" 51 depends on X86 52 help 53 Say Y or M here if you want to enable BIOS Enhanced Disk Drive 54 Services real mode BIOS calls to determine which disk 55 BIOS tries boot from. This information is then exported via sysfs. 56 57 This option is experimental and is known to fail to boot on some 58 obscure configurations. Most disk controller BIOS vendors do 59 not yet implement this feature. 60 61config EDD_OFF 62 bool "Sets default behavior for EDD detection to off" 63 depends on EDD 64 default n 65 help 66 Say Y if you want EDD disabled by default, even though it is compiled into the 67 kernel. Say N if you want EDD enabled by default. EDD can be dynamically set 68 using the kernel parameter 'edd={on|skipmbr|off}'. 69 70config FIRMWARE_MEMMAP 71 bool "Add firmware-provided memory map to sysfs" if EXPERT 72 default X86 73 help 74 Add the firmware-provided (unmodified) memory map to /sys/firmware/memmap. 75 That memory map is used for example by kexec to set up parameter area 76 for the next kernel, but can also be used for debugging purposes. 77 78 See also Documentation/ABI/testing/sysfs-firmware-memmap. 79 80config EFI_PCDP 81 bool "Console device selection via EFI PCDP or HCDP table" 82 depends on ACPI && EFI && IA64 83 default y if IA64 84 help 85 If your firmware supplies the PCDP table, and you want to 86 automatically use the primary console device it describes 87 as the Linux console, say Y here. 88 89 If your firmware supplies the HCDP table, and you want to 90 use the first serial port it describes as the Linux console, 91 say Y here. If your EFI ConOut path contains only a UART 92 device, it will become the console automatically. Otherwise, 93 you must specify the "console=hcdp" kernel boot argument. 94 95 Neither the PCDP nor the HCDP affects naming of serial devices, 96 so a serial console may be /dev/ttyS0, /dev/ttyS1, etc, depending 97 on how the driver discovers devices. 98 99 You must also enable the appropriate drivers (serial, VGA, etc.) 100 101 See DIG64_HCDPv20_042804.pdf available from 102 <http://www.dig64.org/specifications/> 103 104config DMIID 105 bool "Export DMI identification via sysfs to userspace" 106 depends on DMI 107 default y 108 help 109 Say Y here if you want to query SMBIOS/DMI system identification 110 information from userspace through /sys/class/dmi/id/ or if you want 111 DMI-based module auto-loading. 112 113config DMI_SYSFS 114 tristate "DMI table support in sysfs" 115 depends on SYSFS && DMI 116 default n 117 help 118 Say Y or M here to enable the exporting of the raw DMI table 119 data via sysfs. This is useful for consuming the data without 120 requiring any access to /dev/mem at all. Tables are found 121 under /sys/firmware/dmi when this option is enabled and 122 loaded. 123 124config DMI_SCAN_MACHINE_NON_EFI_FALLBACK 125 bool 126 127config ISCSI_IBFT_FIND 128 bool "iSCSI Boot Firmware Table Attributes" 129 depends on X86 && ISCSI_IBFT 130 default n 131 help 132 This option enables the kernel to find the region of memory 133 in which the ISCSI Boot Firmware Table (iBFT) resides. This 134 is necessary for iSCSI Boot Firmware Table Attributes module to work 135 properly. 136 137config ISCSI_IBFT 138 tristate "iSCSI Boot Firmware Table Attributes module" 139 select ISCSI_BOOT_SYSFS 140 select ISCSI_IBFT_FIND if X86 141 depends on ACPI && SCSI && SCSI_LOWLEVEL 142 default n 143 help 144 This option enables support for detection and exposing of iSCSI 145 Boot Firmware Table (iBFT) via sysfs to userspace. If you wish to 146 detect iSCSI boot parameters dynamically during system boot, say Y. 147 Otherwise, say N. 148 149config RASPBERRYPI_FIRMWARE 150 tristate "Raspberry Pi Firmware Driver" 151 depends on BCM2835_MBOX 152 help 153 This option enables support for communicating with the firmware on the 154 Raspberry Pi. 155 156config FW_CFG_SYSFS 157 tristate "QEMU fw_cfg device support in sysfs" 158 depends on SYSFS && (ARM || ARM64 || PARISC || PPC_PMAC || SPARC || X86) 159 depends on HAS_IOPORT_MAP 160 default n 161 help 162 Say Y or M here to enable the exporting of the QEMU firmware 163 configuration (fw_cfg) file entries via sysfs. Entries are 164 found under /sys/firmware/fw_cfg when this option is enabled 165 and loaded. 166 167config FW_CFG_SYSFS_CMDLINE 168 bool "QEMU fw_cfg device parameter parsing" 169 depends on FW_CFG_SYSFS 170 help 171 Allow the qemu_fw_cfg device to be initialized via the kernel 172 command line or using a module parameter. 173 WARNING: Using incorrect parameters (base address in particular) 174 may crash your system. 175 176config INTEL_STRATIX10_SERVICE 177 tristate "Intel Stratix10 Service Layer" 178 depends on ARCH_INTEL_SOCFPGA && ARM64 && HAVE_ARM_SMCCC 179 default n 180 help 181 Intel Stratix10 service layer runs at privileged exception level, 182 interfaces with the service providers (FPGA manager is one of them) 183 and manages secure monitor call to communicate with secure monitor 184 software at secure monitor exception level. 185 186 Say Y here if you want Stratix10 service layer support. 187 188config INTEL_STRATIX10_RSU 189 tristate "Intel Stratix10 Remote System Update" 190 depends on INTEL_STRATIX10_SERVICE 191 help 192 The Intel Remote System Update (RSU) driver exposes interfaces 193 access through the Intel Service Layer to user space via sysfs 194 device attribute nodes. The RSU interfaces report/control some of 195 the optional RSU features of the Stratix 10 SoC FPGA. 196 197 The RSU provides a way for customers to update the boot 198 configuration of a Stratix 10 SoC device with significantly reduced 199 risk of corrupting the bitstream storage and bricking the system. 200 201 Enable RSU support if you are using an Intel SoC FPGA with the RSU 202 feature enabled and you want Linux user space control. 203 204 Say Y here if you want Intel RSU support. 205 206config MTK_ADSP_IPC 207 tristate "MTK ADSP IPC Protocol driver" 208 depends on MTK_ADSP_MBOX 209 help 210 Say yes here to add support for the MediaTek ADSP IPC 211 between host AP (Linux) and the firmware running on ADSP. 212 ADSP exists on some mtk processors. 213 Client might use shared memory to exchange information with ADSP. 214 215config QCOM_SCM 216 tristate 217 218config QCOM_SCM_DOWNLOAD_MODE_DEFAULT 219 bool "Qualcomm download mode enabled by default" 220 depends on QCOM_SCM 221 help 222 A device with "download mode" enabled will upon an unexpected 223 warm-restart enter a special debug mode that allows the user to 224 "download" memory content over USB for offline postmortem analysis. 225 The feature can be enabled/disabled on the kernel command line. 226 227 Say Y here to enable "download mode" by default. 228 229config SYSFB 230 bool 231 select BOOT_VESA_SUPPORT 232 select SCREEN_INFO 233 234config SYSFB_SIMPLEFB 235 bool "Mark VGA/VBE/EFI FB as generic system framebuffer" 236 depends on X86 || EFI 237 select SYSFB 238 help 239 Firmwares often provide initial graphics framebuffers so the BIOS, 240 bootloader or kernel can show basic video-output during boot for 241 user-guidance and debugging. Historically, x86 used the VESA BIOS 242 Extensions and EFI-framebuffers for this, which are mostly limited 243 to x86 BIOS or EFI systems. 244 This option, if enabled, marks VGA/VBE/EFI framebuffers as generic 245 framebuffers so the new generic system-framebuffer drivers can be 246 used instead. If the framebuffer is not compatible with the generic 247 modes, it is advertised as fallback platform framebuffer so legacy 248 drivers like efifb, vesafb and uvesafb can pick it up. 249 If this option is not selected, all system framebuffers are always 250 marked as fallback platform framebuffers as usual. 251 252 Note: Legacy fbdev drivers, including vesafb, efifb, uvesafb, will 253 not be able to pick up generic system framebuffers if this option 254 is selected. You are highly encouraged to enable simplefb as 255 replacement if you select this option. simplefb can correctly deal 256 with generic system framebuffers. But you should still keep vesafb 257 and others enabled as fallback if a system framebuffer is 258 incompatible with simplefb. 259 260 If unsure, say Y. 261 262config TI_SCI_PROTOCOL 263 tristate "TI System Control Interface (TISCI) Message Protocol" 264 depends on TI_MESSAGE_MANAGER 265 help 266 TI System Control Interface (TISCI) Message Protocol is used to manage 267 compute systems such as ARM, DSP etc with the system controller in 268 complex System on Chip(SoC) such as those found on certain keystone 269 generation SoC from TI. 270 271 System controller provides various facilities including power 272 management function support. 273 274 This protocol library is used by client drivers to use the features 275 provided by the system controller. 276 277config TRUSTED_FOUNDATIONS 278 bool "Trusted Foundations secure monitor support" 279 depends on ARM && CPU_V7 280 help 281 Some devices (including most early Tegra-based consumer devices on 282 the market) are booted with the Trusted Foundations secure monitor 283 active, requiring some core operations to be performed by the secure 284 monitor instead of the kernel. 285 286 This option allows the kernel to invoke the secure monitor whenever 287 required on devices using Trusted Foundations. See the functions and 288 comments in linux/firmware/trusted_foundations.h or the device tree 289 bindings for "tlm,trusted-foundations" for details on how to use it. 290 291 Choose N if you don't know what this is about. 292 293config TURRIS_MOX_RWTM 294 tristate "Turris Mox rWTM secure firmware driver" 295 depends on ARCH_MVEBU || COMPILE_TEST 296 depends on HAS_DMA && OF 297 depends on MAILBOX 298 select HW_RANDOM 299 select ARMADA_37XX_RWTM_MBOX 300 help 301 This driver communicates with the firmware on the Cortex-M3 secure 302 processor of the Turris Mox router. Enable if you are building for 303 Turris Mox, and you will be able to read the device serial number and 304 other manufacturing data and also utilize the Entropy Bit Generator 305 for hardware random number generation. 306 307source "drivers/firmware/arm_ffa/Kconfig" 308source "drivers/firmware/broadcom/Kconfig" 309source "drivers/firmware/cirrus/Kconfig" 310source "drivers/firmware/google/Kconfig" 311source "drivers/firmware/efi/Kconfig" 312source "drivers/firmware/imx/Kconfig" 313source "drivers/firmware/meson/Kconfig" 314source "drivers/firmware/psci/Kconfig" 315source "drivers/firmware/smccc/Kconfig" 316source "drivers/firmware/tegra/Kconfig" 317source "drivers/firmware/xilinx/Kconfig" 318 319endmenu 320