1 // SPDX-License-Identifier: GPL-2.0
2 /*
3  * Extcon charger detection driver for Intel Cherrytrail Whiskey Cove PMIC
4  * Copyright (C) 2017 Hans de Goede <hdegoede@redhat.com>
5  *
6  * Based on various non upstream patches to support the CHT Whiskey Cove PMIC:
7  * Copyright (C) 2013-2015 Intel Corporation. All rights reserved.
8  */
9 
10 #include <linux/extcon-provider.h>
11 #include <linux/interrupt.h>
12 #include <linux/kernel.h>
13 #include <linux/mfd/intel_soc_pmic.h>
14 #include <linux/module.h>
15 #include <linux/mod_devicetable.h>
16 #include <linux/platform_device.h>
17 #include <linux/regmap.h>
18 #include <linux/slab.h>
19 
20 #include "extcon-intel.h"
21 
22 #define CHT_WC_PHYCTRL			0x5e07
23 
24 #define CHT_WC_CHGRCTRL0		0x5e16
25 #define CHT_WC_CHGRCTRL0_CHGRRESET	BIT(0)
26 #define CHT_WC_CHGRCTRL0_EMRGCHREN	BIT(1)
27 #define CHT_WC_CHGRCTRL0_EXTCHRDIS	BIT(2)
28 #define CHT_WC_CHGRCTRL0_SWCONTROL	BIT(3)
29 #define CHT_WC_CHGRCTRL0_TTLCK		BIT(4)
30 #define CHT_WC_CHGRCTRL0_CCSM_OFF	BIT(5)
31 #define CHT_WC_CHGRCTRL0_DBPOFF		BIT(6)
32 #define CHT_WC_CHGRCTRL0_CHR_WDT_NOKICK	BIT(7)
33 
34 #define CHT_WC_CHGRCTRL1			0x5e17
35 #define CHT_WC_CHGRCTRL1_FUSB_INLMT_100		BIT(0)
36 #define CHT_WC_CHGRCTRL1_FUSB_INLMT_150		BIT(1)
37 #define CHT_WC_CHGRCTRL1_FUSB_INLMT_500		BIT(2)
38 #define CHT_WC_CHGRCTRL1_FUSB_INLMT_900		BIT(3)
39 #define CHT_WC_CHGRCTRL1_FUSB_INLMT_1500	BIT(4)
40 #define CHT_WC_CHGRCTRL1_FTEMP_EVENT		BIT(5)
41 #define CHT_WC_CHGRCTRL1_OTGMODE		BIT(6)
42 #define CHT_WC_CHGRCTRL1_DBPEN			BIT(7)
43 
44 #define CHT_WC_USBSRC			0x5e29
45 #define CHT_WC_USBSRC_STS_MASK		GENMASK(1, 0)
46 #define CHT_WC_USBSRC_STS_SUCCESS	2
47 #define CHT_WC_USBSRC_STS_FAIL		3
48 #define CHT_WC_USBSRC_TYPE_SHIFT	2
49 #define CHT_WC_USBSRC_TYPE_MASK		GENMASK(5, 2)
50 #define CHT_WC_USBSRC_TYPE_NONE		0
51 #define CHT_WC_USBSRC_TYPE_SDP		1
52 #define CHT_WC_USBSRC_TYPE_DCP		2
53 #define CHT_WC_USBSRC_TYPE_CDP		3
54 #define CHT_WC_USBSRC_TYPE_ACA		4
55 #define CHT_WC_USBSRC_TYPE_SE1		5
56 #define CHT_WC_USBSRC_TYPE_MHL		6
57 #define CHT_WC_USBSRC_TYPE_FLOATING	7
58 #define CHT_WC_USBSRC_TYPE_OTHER	8
59 #define CHT_WC_USBSRC_TYPE_DCP_EXTPHY	9
60 
61 #define CHT_WC_CHGDISCTRL		0x5e2f
62 #define CHT_WC_CHGDISCTRL_OUT		BIT(0)
63 /* 0 - open drain, 1 - regular push-pull output */
64 #define CHT_WC_CHGDISCTRL_DRV		BIT(4)
65 /* 0 - pin is controlled by SW, 1 - by HW */
66 #define CHT_WC_CHGDISCTRL_FN		BIT(6)
67 
68 #define CHT_WC_PWRSRC_IRQ		0x6e03
69 #define CHT_WC_PWRSRC_IRQ_MASK		0x6e0f
70 #define CHT_WC_PWRSRC_STS		0x6e1e
71 #define CHT_WC_PWRSRC_VBUS		BIT(0)
72 #define CHT_WC_PWRSRC_DC		BIT(1)
73 #define CHT_WC_PWRSRC_BATT		BIT(2)
74 #define CHT_WC_PWRSRC_USBID_MASK	GENMASK(4, 3)
75 #define CHT_WC_PWRSRC_USBID_SHIFT	3
76 #define CHT_WC_PWRSRC_RID_ACA		0
77 #define CHT_WC_PWRSRC_RID_GND		1
78 #define CHT_WC_PWRSRC_RID_FLOAT		2
79 
80 #define CHT_WC_VBUS_GPIO_CTLO		0x6e2d
81 #define CHT_WC_VBUS_GPIO_CTLO_OUTPUT	BIT(0)
82 #define CHT_WC_VBUS_GPIO_CTLO_DRV_OD	BIT(4)
83 #define CHT_WC_VBUS_GPIO_CTLO_DIR_OUT	BIT(5)
84 
85 enum cht_wc_mux_select {
86 	MUX_SEL_PMIC = 0,
87 	MUX_SEL_SOC,
88 };
89 
90 static const unsigned int cht_wc_extcon_cables[] = {
91 	EXTCON_USB,
92 	EXTCON_USB_HOST,
93 	EXTCON_CHG_USB_SDP,
94 	EXTCON_CHG_USB_CDP,
95 	EXTCON_CHG_USB_DCP,
96 	EXTCON_CHG_USB_ACA,
97 	EXTCON_NONE,
98 };
99 
100 struct cht_wc_extcon_data {
101 	struct device *dev;
102 	struct regmap *regmap;
103 	struct extcon_dev *edev;
104 	unsigned int previous_cable;
105 	bool usb_host;
106 };
107 
108 static int cht_wc_extcon_get_id(struct cht_wc_extcon_data *ext, int pwrsrc_sts)
109 {
110 	switch ((pwrsrc_sts & CHT_WC_PWRSRC_USBID_MASK) >> CHT_WC_PWRSRC_USBID_SHIFT) {
111 	case CHT_WC_PWRSRC_RID_GND:
112 		return INTEL_USB_ID_GND;
113 	case CHT_WC_PWRSRC_RID_FLOAT:
114 		return INTEL_USB_ID_FLOAT;
115 	case CHT_WC_PWRSRC_RID_ACA:
116 	default:
117 		/*
118 		 * Once we have IIO support for the GPADC we should read
119 		 * the USBID GPADC channel here and determine ACA role
120 		 * based on that.
121 		 */
122 		return INTEL_USB_ID_FLOAT;
123 	}
124 }
125 
126 static int cht_wc_extcon_get_charger(struct cht_wc_extcon_data *ext,
127 				     bool ignore_errors)
128 {
129 	int ret, usbsrc, status;
130 	unsigned long timeout;
131 
132 	/* Charger detection can take upto 600ms, wait 800ms max. */
133 	timeout = jiffies + msecs_to_jiffies(800);
134 	do {
135 		ret = regmap_read(ext->regmap, CHT_WC_USBSRC, &usbsrc);
136 		if (ret) {
137 			dev_err(ext->dev, "Error reading usbsrc: %d\n", ret);
138 			return ret;
139 		}
140 
141 		status = usbsrc & CHT_WC_USBSRC_STS_MASK;
142 		if (status == CHT_WC_USBSRC_STS_SUCCESS ||
143 		    status == CHT_WC_USBSRC_STS_FAIL)
144 			break;
145 
146 		msleep(50); /* Wait a bit before retrying */
147 	} while (time_before(jiffies, timeout));
148 
149 	if (status != CHT_WC_USBSRC_STS_SUCCESS) {
150 		if (ignore_errors)
151 			return EXTCON_CHG_USB_SDP; /* Save fallback */
152 
153 		if (status == CHT_WC_USBSRC_STS_FAIL)
154 			dev_warn(ext->dev, "Could not detect charger type\n");
155 		else
156 			dev_warn(ext->dev, "Timeout detecting charger type\n");
157 		return EXTCON_CHG_USB_SDP; /* Save fallback */
158 	}
159 
160 	usbsrc = (usbsrc & CHT_WC_USBSRC_TYPE_MASK) >> CHT_WC_USBSRC_TYPE_SHIFT;
161 	switch (usbsrc) {
162 	default:
163 		dev_warn(ext->dev,
164 			"Unhandled charger type %d, defaulting to SDP\n",
165 			 ret);
166 		return EXTCON_CHG_USB_SDP;
167 	case CHT_WC_USBSRC_TYPE_SDP:
168 	case CHT_WC_USBSRC_TYPE_FLOATING:
169 	case CHT_WC_USBSRC_TYPE_OTHER:
170 		return EXTCON_CHG_USB_SDP;
171 	case CHT_WC_USBSRC_TYPE_CDP:
172 		return EXTCON_CHG_USB_CDP;
173 	case CHT_WC_USBSRC_TYPE_DCP:
174 	case CHT_WC_USBSRC_TYPE_DCP_EXTPHY:
175 	case CHT_WC_USBSRC_TYPE_MHL: /* MHL2+ delivers upto 2A, treat as DCP */
176 		return EXTCON_CHG_USB_DCP;
177 	case CHT_WC_USBSRC_TYPE_ACA:
178 		return EXTCON_CHG_USB_ACA;
179 	}
180 }
181 
182 static void cht_wc_extcon_set_phymux(struct cht_wc_extcon_data *ext, u8 state)
183 {
184 	int ret;
185 
186 	ret = regmap_write(ext->regmap, CHT_WC_PHYCTRL, state);
187 	if (ret)
188 		dev_err(ext->dev, "Error writing phyctrl: %d\n", ret);
189 }
190 
191 static void cht_wc_extcon_set_5v_boost(struct cht_wc_extcon_data *ext,
192 				       bool enable)
193 {
194 	int ret, val;
195 
196 	/*
197 	 * The 5V boost converter is enabled through a gpio on the PMIC, since
198 	 * there currently is no gpio driver we access the gpio reg directly.
199 	 */
200 	val = CHT_WC_VBUS_GPIO_CTLO_DRV_OD | CHT_WC_VBUS_GPIO_CTLO_DIR_OUT;
201 	if (enable)
202 		val |= CHT_WC_VBUS_GPIO_CTLO_OUTPUT;
203 
204 	ret = regmap_write(ext->regmap, CHT_WC_VBUS_GPIO_CTLO, val);
205 	if (ret)
206 		dev_err(ext->dev, "Error writing Vbus GPIO CTLO: %d\n", ret);
207 }
208 
209 static void cht_wc_extcon_set_otgmode(struct cht_wc_extcon_data *ext,
210 				      bool enable)
211 {
212 	unsigned int val = enable ? CHT_WC_CHGRCTRL1_OTGMODE : 0;
213 	int ret;
214 
215 	ret = regmap_update_bits(ext->regmap, CHT_WC_CHGRCTRL1,
216 				 CHT_WC_CHGRCTRL1_OTGMODE, val);
217 	if (ret)
218 		dev_err(ext->dev, "Error updating CHGRCTRL1 reg: %d\n", ret);
219 }
220 
221 static void cht_wc_extcon_enable_charging(struct cht_wc_extcon_data *ext,
222 					  bool enable)
223 {
224 	unsigned int val = enable ? 0 : CHT_WC_CHGDISCTRL_OUT;
225 	int ret;
226 
227 	ret = regmap_update_bits(ext->regmap, CHT_WC_CHGDISCTRL,
228 				 CHT_WC_CHGDISCTRL_OUT, val);
229 	if (ret)
230 		dev_err(ext->dev, "Error updating CHGDISCTRL reg: %d\n", ret);
231 }
232 
233 /* Small helper to sync EXTCON_CHG_USB_SDP and EXTCON_USB state */
234 static void cht_wc_extcon_set_state(struct cht_wc_extcon_data *ext,
235 				    unsigned int cable, bool state)
236 {
237 	extcon_set_state_sync(ext->edev, cable, state);
238 	if (cable == EXTCON_CHG_USB_SDP)
239 		extcon_set_state_sync(ext->edev, EXTCON_USB, state);
240 }
241 
242 static void cht_wc_extcon_pwrsrc_event(struct cht_wc_extcon_data *ext)
243 {
244 	int ret, pwrsrc_sts, id;
245 	unsigned int cable = EXTCON_NONE;
246 	/* Ignore errors in host mode, as the 5v boost converter is on then */
247 	bool ignore_get_charger_errors = ext->usb_host;
248 
249 	ret = regmap_read(ext->regmap, CHT_WC_PWRSRC_STS, &pwrsrc_sts);
250 	if (ret) {
251 		dev_err(ext->dev, "Error reading pwrsrc status: %d\n", ret);
252 		return;
253 	}
254 
255 	id = cht_wc_extcon_get_id(ext, pwrsrc_sts);
256 	if (id == INTEL_USB_ID_GND) {
257 		cht_wc_extcon_enable_charging(ext, false);
258 		cht_wc_extcon_set_otgmode(ext, true);
259 
260 		/* The 5v boost causes a false VBUS / SDP detect, skip */
261 		goto charger_det_done;
262 	}
263 
264 	cht_wc_extcon_set_otgmode(ext, false);
265 	cht_wc_extcon_enable_charging(ext, true);
266 
267 	/* Plugged into a host/charger or not connected? */
268 	if (!(pwrsrc_sts & CHT_WC_PWRSRC_VBUS)) {
269 		/* Route D+ and D- to PMIC for future charger detection */
270 		cht_wc_extcon_set_phymux(ext, MUX_SEL_PMIC);
271 		goto set_state;
272 	}
273 
274 	ret = cht_wc_extcon_get_charger(ext, ignore_get_charger_errors);
275 	if (ret >= 0)
276 		cable = ret;
277 
278 charger_det_done:
279 	/* Route D+ and D- to SoC for the host or gadget controller */
280 	cht_wc_extcon_set_phymux(ext, MUX_SEL_SOC);
281 
282 set_state:
283 	if (cable != ext->previous_cable) {
284 		cht_wc_extcon_set_state(ext, cable, true);
285 		cht_wc_extcon_set_state(ext, ext->previous_cable, false);
286 		ext->previous_cable = cable;
287 	}
288 
289 	ext->usb_host = ((id == INTEL_USB_ID_GND) || (id == INTEL_USB_RID_A));
290 	extcon_set_state_sync(ext->edev, EXTCON_USB_HOST, ext->usb_host);
291 }
292 
293 static irqreturn_t cht_wc_extcon_isr(int irq, void *data)
294 {
295 	struct cht_wc_extcon_data *ext = data;
296 	int ret, irqs;
297 
298 	ret = regmap_read(ext->regmap, CHT_WC_PWRSRC_IRQ, &irqs);
299 	if (ret) {
300 		dev_err(ext->dev, "Error reading irqs: %d\n", ret);
301 		return IRQ_NONE;
302 	}
303 
304 	cht_wc_extcon_pwrsrc_event(ext);
305 
306 	ret = regmap_write(ext->regmap, CHT_WC_PWRSRC_IRQ, irqs);
307 	if (ret) {
308 		dev_err(ext->dev, "Error writing irqs: %d\n", ret);
309 		return IRQ_NONE;
310 	}
311 
312 	return IRQ_HANDLED;
313 }
314 
315 static int cht_wc_extcon_sw_control(struct cht_wc_extcon_data *ext, bool enable)
316 {
317 	int ret, mask, val;
318 
319 	val = enable ? 0 : CHT_WC_CHGDISCTRL_FN;
320 	ret = regmap_update_bits(ext->regmap, CHT_WC_CHGDISCTRL,
321 				 CHT_WC_CHGDISCTRL_FN, val);
322 	if (ret)
323 		dev_err(ext->dev,
324 			"Error setting sw control for CHGDIS pin: %d\n",
325 			ret);
326 
327 	mask = CHT_WC_CHGRCTRL0_SWCONTROL | CHT_WC_CHGRCTRL0_CCSM_OFF;
328 	val = enable ? mask : 0;
329 	ret = regmap_update_bits(ext->regmap, CHT_WC_CHGRCTRL0, mask, val);
330 	if (ret)
331 		dev_err(ext->dev, "Error setting sw control: %d\n", ret);
332 
333 	return ret;
334 }
335 
336 static int cht_wc_extcon_probe(struct platform_device *pdev)
337 {
338 	struct intel_soc_pmic *pmic = dev_get_drvdata(pdev->dev.parent);
339 	struct cht_wc_extcon_data *ext;
340 	unsigned long mask = ~(CHT_WC_PWRSRC_VBUS | CHT_WC_PWRSRC_USBID_MASK);
341 	int pwrsrc_sts, id;
342 	int irq, ret;
343 
344 	irq = platform_get_irq(pdev, 0);
345 	if (irq < 0)
346 		return irq;
347 
348 	ext = devm_kzalloc(&pdev->dev, sizeof(*ext), GFP_KERNEL);
349 	if (!ext)
350 		return -ENOMEM;
351 
352 	ext->dev = &pdev->dev;
353 	ext->regmap = pmic->regmap;
354 	ext->previous_cable = EXTCON_NONE;
355 
356 	/* Initialize extcon device */
357 	ext->edev = devm_extcon_dev_allocate(ext->dev, cht_wc_extcon_cables);
358 	if (IS_ERR(ext->edev))
359 		return PTR_ERR(ext->edev);
360 
361 	/*
362 	 * When a host-cable is detected the BIOS enables an external 5v boost
363 	 * converter to power connected devices there are 2 problems with this:
364 	 * 1) This gets seen by the external battery charger as a valid Vbus
365 	 *    supply and it then tries to feed Vsys from this creating a
366 	 *    feedback loop which causes aprox. 300 mA extra battery drain
367 	 *    (and unless we drive the external-charger-disable pin high it
368 	 *    also tries to charge the battery causing even more feedback).
369 	 * 2) This gets seen by the pwrsrc block as a SDP USB Vbus supply
370 	 * Since the external battery charger has its own 5v boost converter
371 	 * which does not have these issues, we simply turn the separate
372 	 * external 5v boost converter off and leave it off entirely.
373 	 */
374 	cht_wc_extcon_set_5v_boost(ext, false);
375 
376 	/* Enable sw control */
377 	ret = cht_wc_extcon_sw_control(ext, true);
378 	if (ret)
379 		goto disable_sw_control;
380 
381 	/* Disable charging by external battery charger */
382 	cht_wc_extcon_enable_charging(ext, false);
383 
384 	/* Register extcon device */
385 	ret = devm_extcon_dev_register(ext->dev, ext->edev);
386 	if (ret) {
387 		dev_err(ext->dev, "Error registering extcon device: %d\n", ret);
388 		goto disable_sw_control;
389 	}
390 
391 	ret = regmap_read(ext->regmap, CHT_WC_PWRSRC_STS, &pwrsrc_sts);
392 	if (ret) {
393 		dev_err(ext->dev, "Error reading pwrsrc status: %d\n", ret);
394 		goto disable_sw_control;
395 	}
396 
397 	/*
398 	 * If no USB host or device connected, route D+ and D- to PMIC for
399 	 * initial charger detection
400 	 */
401 	id = cht_wc_extcon_get_id(ext, pwrsrc_sts);
402 	if (id != INTEL_USB_ID_GND)
403 		cht_wc_extcon_set_phymux(ext, MUX_SEL_PMIC);
404 
405 	/* Get initial state */
406 	cht_wc_extcon_pwrsrc_event(ext);
407 
408 	ret = devm_request_threaded_irq(ext->dev, irq, NULL, cht_wc_extcon_isr,
409 					IRQF_ONESHOT, pdev->name, ext);
410 	if (ret) {
411 		dev_err(ext->dev, "Error requesting interrupt: %d\n", ret);
412 		goto disable_sw_control;
413 	}
414 
415 	/* Unmask irqs */
416 	ret = regmap_write(ext->regmap, CHT_WC_PWRSRC_IRQ_MASK, mask);
417 	if (ret) {
418 		dev_err(ext->dev, "Error writing irq-mask: %d\n", ret);
419 		goto disable_sw_control;
420 	}
421 
422 	platform_set_drvdata(pdev, ext);
423 
424 	return 0;
425 
426 disable_sw_control:
427 	cht_wc_extcon_sw_control(ext, false);
428 	return ret;
429 }
430 
431 static int cht_wc_extcon_remove(struct platform_device *pdev)
432 {
433 	struct cht_wc_extcon_data *ext = platform_get_drvdata(pdev);
434 
435 	cht_wc_extcon_sw_control(ext, false);
436 
437 	return 0;
438 }
439 
440 static const struct platform_device_id cht_wc_extcon_table[] = {
441 	{ .name = "cht_wcove_pwrsrc" },
442 	{},
443 };
444 MODULE_DEVICE_TABLE(platform, cht_wc_extcon_table);
445 
446 static struct platform_driver cht_wc_extcon_driver = {
447 	.probe = cht_wc_extcon_probe,
448 	.remove = cht_wc_extcon_remove,
449 	.id_table = cht_wc_extcon_table,
450 	.driver = {
451 		.name = "cht_wcove_pwrsrc",
452 	},
453 };
454 module_platform_driver(cht_wc_extcon_driver);
455 
456 MODULE_DESCRIPTION("Intel Cherrytrail Whiskey Cove PMIC extcon driver");
457 MODULE_AUTHOR("Hans de Goede <hdegoede@redhat.com>");
458 MODULE_LICENSE("GPL v2");
459