1 /* 2 * Radisys 82600 Embedded chipset Memory Controller kernel module 3 * (C) 2005 EADS Astrium 4 * This file may be distributed under the terms of the 5 * GNU General Public License. 6 * 7 * Written by Tim Small <tim@buttersideup.com>, based on work by Thayne 8 * Harbaugh, Dan Hollis <goemon at anime dot net> and others. 9 * 10 * $Id: edac_r82600.c,v 1.1.2.6 2005/10/05 00:43:44 dsp_llnl Exp $ 11 * 12 * Written with reference to 82600 High Integration Dual PCI System 13 * Controller Data Book: 14 * www.radisys.com/files/support_downloads/007-01277-0002.82600DataBook.pdf 15 * references to this document given in [] 16 */ 17 18 #include <linux/module.h> 19 #include <linux/init.h> 20 #include <linux/pci.h> 21 #include <linux/pci_ids.h> 22 #include <linux/edac.h> 23 #include "edac_core.h" 24 25 #define R82600_REVISION " Ver: 2.0.2" 26 #define EDAC_MOD_STR "r82600_edac" 27 28 #define r82600_printk(level, fmt, arg...) \ 29 edac_printk(level, "r82600", fmt, ##arg) 30 31 #define r82600_mc_printk(mci, level, fmt, arg...) \ 32 edac_mc_chipset_printk(mci, level, "r82600", fmt, ##arg) 33 34 /* Radisys say "The 82600 integrates a main memory SDRAM controller that 35 * supports up to four banks of memory. The four banks can support a mix of 36 * sizes of 64 bit wide (72 bits with ECC) Synchronous DRAM (SDRAM) DIMMs, 37 * each of which can be any size from 16MB to 512MB. Both registered (control 38 * signals buffered) and unbuffered DIMM types are supported. Mixing of 39 * registered and unbuffered DIMMs as well as mixing of ECC and non-ECC DIMMs 40 * is not allowed. The 82600 SDRAM interface operates at the same frequency as 41 * the CPU bus, 66MHz, 100MHz or 133MHz." 42 */ 43 44 #define R82600_NR_CSROWS 4 45 #define R82600_NR_CHANS 1 46 #define R82600_NR_DIMMS 4 47 48 #define R82600_BRIDGE_ID 0x8200 49 50 /* Radisys 82600 register addresses - device 0 function 0 - PCI bridge */ 51 #define R82600_DRAMC 0x57 /* Various SDRAM related control bits 52 * all bits are R/W 53 * 54 * 7 SDRAM ISA Hole Enable 55 * 6 Flash Page Mode Enable 56 * 5 ECC Enable: 1=ECC 0=noECC 57 * 4 DRAM DIMM Type: 1= 58 * 3 BIOS Alias Disable 59 * 2 SDRAM BIOS Flash Write Enable 60 * 1:0 SDRAM Refresh Rate: 00=Disabled 61 * 01=7.8usec (256Mbit SDRAMs) 62 * 10=15.6us 11=125usec 63 */ 64 65 #define R82600_SDRAMC 0x76 /* "SDRAM Control Register" 66 * More SDRAM related control bits 67 * all bits are R/W 68 * 69 * 15:8 Reserved. 70 * 71 * 7:5 Special SDRAM Mode Select 72 * 73 * 4 Force ECC 74 * 75 * 1=Drive ECC bits to 0 during 76 * write cycles (i.e. ECC test mode) 77 * 78 * 0=Normal ECC functioning 79 * 80 * 3 Enhanced Paging Enable 81 * 82 * 2 CAS# Latency 0=3clks 1=2clks 83 * 84 * 1 RAS# to CAS# Delay 0=3 1=2 85 * 86 * 0 RAS# Precharge 0=3 1=2 87 */ 88 89 #define R82600_EAP 0x80 /* ECC Error Address Pointer Register 90 * 91 * 31 Disable Hardware Scrubbing (RW) 92 * 0=Scrub on corrected read 93 * 1=Don't scrub on corrected read 94 * 95 * 30:12 Error Address Pointer (RO) 96 * Upper 19 bits of error address 97 * 98 * 11:4 Syndrome Bits (RO) 99 * 100 * 3 BSERR# on multibit error (RW) 101 * 1=enable 0=disable 102 * 103 * 2 NMI on Single Bit Eror (RW) 104 * 1=NMI triggered by SBE n.b. other 105 * prerequeists 106 * 0=NMI not triggered 107 * 108 * 1 MBE (R/WC) 109 * read 1=MBE at EAP (see above) 110 * read 0=no MBE, or SBE occurred first 111 * write 1=Clear MBE status (must also 112 * clear SBE) 113 * write 0=NOP 114 * 115 * 1 SBE (R/WC) 116 * read 1=SBE at EAP (see above) 117 * read 0=no SBE, or MBE occurred first 118 * write 1=Clear SBE status (must also 119 * clear MBE) 120 * write 0=NOP 121 */ 122 123 #define R82600_DRBA 0x60 /* + 0x60..0x63 SDRAM Row Boundary Address 124 * Registers 125 * 126 * 7:0 Address lines 30:24 - upper limit of 127 * each row [p57] 128 */ 129 130 struct r82600_error_info { 131 u32 eapr; 132 }; 133 134 static bool disable_hardware_scrub; 135 136 static struct edac_pci_ctl_info *r82600_pci; 137 138 static void r82600_get_error_info(struct mem_ctl_info *mci, 139 struct r82600_error_info *info) 140 { 141 struct pci_dev *pdev; 142 143 pdev = to_pci_dev(mci->dev); 144 pci_read_config_dword(pdev, R82600_EAP, &info->eapr); 145 146 if (info->eapr & BIT(0)) 147 /* Clear error to allow next error to be reported [p.62] */ 148 pci_write_bits32(pdev, R82600_EAP, 149 ((u32) BIT(0) & (u32) BIT(1)), 150 ((u32) BIT(0) & (u32) BIT(1))); 151 152 if (info->eapr & BIT(1)) 153 /* Clear error to allow next error to be reported [p.62] */ 154 pci_write_bits32(pdev, R82600_EAP, 155 ((u32) BIT(0) & (u32) BIT(1)), 156 ((u32) BIT(0) & (u32) BIT(1))); 157 } 158 159 static int r82600_process_error_info(struct mem_ctl_info *mci, 160 struct r82600_error_info *info, 161 int handle_errors) 162 { 163 int error_found; 164 u32 eapaddr, page; 165 u32 syndrome; 166 167 error_found = 0; 168 169 /* bits 30:12 store the upper 19 bits of the 32 bit error address */ 170 eapaddr = ((info->eapr >> 12) & 0x7FFF) << 13; 171 /* Syndrome in bits 11:4 [p.62] */ 172 syndrome = (info->eapr >> 4) & 0xFF; 173 174 /* the R82600 reports at less than page * 175 * granularity (upper 19 bits only) */ 176 page = eapaddr >> PAGE_SHIFT; 177 178 if (info->eapr & BIT(0)) { /* CE? */ 179 error_found = 1; 180 181 if (handle_errors) 182 edac_mc_handle_ce(mci, page, 0, /* not avail */ 183 syndrome, 184 edac_mc_find_csrow_by_page(mci, page), 185 0, mci->ctl_name); 186 } 187 188 if (info->eapr & BIT(1)) { /* UE? */ 189 error_found = 1; 190 191 if (handle_errors) 192 /* 82600 doesn't give enough info */ 193 edac_mc_handle_ue(mci, page, 0, 194 edac_mc_find_csrow_by_page(mci, page), 195 mci->ctl_name); 196 } 197 198 return error_found; 199 } 200 201 static void r82600_check(struct mem_ctl_info *mci) 202 { 203 struct r82600_error_info info; 204 205 debugf1("MC%d: %s()\n", mci->mc_idx, __func__); 206 r82600_get_error_info(mci, &info); 207 r82600_process_error_info(mci, &info, 1); 208 } 209 210 static inline int ecc_enabled(u8 dramcr) 211 { 212 return dramcr & BIT(5); 213 } 214 215 static void r82600_init_csrows(struct mem_ctl_info *mci, struct pci_dev *pdev, 216 u8 dramcr) 217 { 218 struct csrow_info *csrow; 219 int index; 220 u8 drbar; /* SDRAM Row Boundary Address Register */ 221 u32 row_high_limit, row_high_limit_last; 222 u32 reg_sdram, ecc_on, row_base; 223 224 ecc_on = ecc_enabled(dramcr); 225 reg_sdram = dramcr & BIT(4); 226 row_high_limit_last = 0; 227 228 for (index = 0; index < mci->nr_csrows; index++) { 229 csrow = &mci->csrows[index]; 230 231 /* find the DRAM Chip Select Base address and mask */ 232 pci_read_config_byte(pdev, R82600_DRBA + index, &drbar); 233 234 debugf1("%s() Row=%d DRBA = %#0x\n", __func__, index, drbar); 235 236 row_high_limit = ((u32) drbar << 24); 237 /* row_high_limit = ((u32)drbar << 24) | 0xffffffUL; */ 238 239 debugf1("%s() Row=%d, Boundary Address=%#0x, Last = %#0x\n", 240 __func__, index, row_high_limit, row_high_limit_last); 241 242 /* Empty row [p.57] */ 243 if (row_high_limit == row_high_limit_last) 244 continue; 245 246 row_base = row_high_limit_last; 247 248 csrow->first_page = row_base >> PAGE_SHIFT; 249 csrow->last_page = (row_high_limit >> PAGE_SHIFT) - 1; 250 csrow->nr_pages = csrow->last_page - csrow->first_page + 1; 251 /* Error address is top 19 bits - so granularity is * 252 * 14 bits */ 253 csrow->grain = 1 << 14; 254 csrow->mtype = reg_sdram ? MEM_RDDR : MEM_DDR; 255 /* FIXME - check that this is unknowable with this chipset */ 256 csrow->dtype = DEV_UNKNOWN; 257 258 /* Mode is global on 82600 */ 259 csrow->edac_mode = ecc_on ? EDAC_SECDED : EDAC_NONE; 260 row_high_limit_last = row_high_limit; 261 } 262 } 263 264 static int r82600_probe1(struct pci_dev *pdev, int dev_idx) 265 { 266 struct mem_ctl_info *mci; 267 u8 dramcr; 268 u32 eapr; 269 u32 scrub_disabled; 270 u32 sdram_refresh_rate; 271 struct r82600_error_info discard; 272 273 debugf0("%s()\n", __func__); 274 pci_read_config_byte(pdev, R82600_DRAMC, &dramcr); 275 pci_read_config_dword(pdev, R82600_EAP, &eapr); 276 scrub_disabled = eapr & BIT(31); 277 sdram_refresh_rate = dramcr & (BIT(0) | BIT(1)); 278 debugf2("%s(): sdram refresh rate = %#0x\n", __func__, 279 sdram_refresh_rate); 280 debugf2("%s(): DRAMC register = %#0x\n", __func__, dramcr); 281 mci = edac_mc_alloc(0, R82600_NR_CSROWS, R82600_NR_CHANS, 0); 282 283 if (mci == NULL) 284 return -ENOMEM; 285 286 debugf0("%s(): mci = %p\n", __func__, mci); 287 mci->dev = &pdev->dev; 288 mci->mtype_cap = MEM_FLAG_RDDR | MEM_FLAG_DDR; 289 mci->edac_ctl_cap = EDAC_FLAG_NONE | EDAC_FLAG_EC | EDAC_FLAG_SECDED; 290 /* FIXME try to work out if the chip leads have been used for COM2 291 * instead on this board? [MA6?] MAYBE: 292 */ 293 294 /* On the R82600, the pins for memory bits 72:65 - i.e. the * 295 * EC bits are shared with the pins for COM2 (!), so if COM2 * 296 * is enabled, we assume COM2 is wired up, and thus no EDAC * 297 * is possible. */ 298 mci->edac_cap = EDAC_FLAG_NONE | EDAC_FLAG_EC | EDAC_FLAG_SECDED; 299 300 if (ecc_enabled(dramcr)) { 301 if (scrub_disabled) 302 debugf3("%s(): mci = %p - Scrubbing disabled! EAP: " 303 "%#0x\n", __func__, mci, eapr); 304 } else 305 mci->edac_cap = EDAC_FLAG_NONE; 306 307 mci->mod_name = EDAC_MOD_STR; 308 mci->mod_ver = R82600_REVISION; 309 mci->ctl_name = "R82600"; 310 mci->dev_name = pci_name(pdev); 311 mci->edac_check = r82600_check; 312 mci->ctl_page_to_phys = NULL; 313 r82600_init_csrows(mci, pdev, dramcr); 314 r82600_get_error_info(mci, &discard); /* clear counters */ 315 316 /* Here we assume that we will never see multiple instances of this 317 * type of memory controller. The ID is therefore hardcoded to 0. 318 */ 319 if (edac_mc_add_mc(mci)) { 320 debugf3("%s(): failed edac_mc_add_mc()\n", __func__); 321 goto fail; 322 } 323 324 /* get this far and it's successful */ 325 326 if (disable_hardware_scrub) { 327 debugf3("%s(): Disabling Hardware Scrub (scrub on error)\n", 328 __func__); 329 pci_write_bits32(pdev, R82600_EAP, BIT(31), BIT(31)); 330 } 331 332 /* allocating generic PCI control info */ 333 r82600_pci = edac_pci_create_generic_ctl(&pdev->dev, EDAC_MOD_STR); 334 if (!r82600_pci) { 335 printk(KERN_WARNING 336 "%s(): Unable to create PCI control\n", 337 __func__); 338 printk(KERN_WARNING 339 "%s(): PCI error report via EDAC not setup\n", 340 __func__); 341 } 342 343 debugf3("%s(): success\n", __func__); 344 return 0; 345 346 fail: 347 edac_mc_free(mci); 348 return -ENODEV; 349 } 350 351 /* returns count (>= 0), or negative on error */ 352 static int __devinit r82600_init_one(struct pci_dev *pdev, 353 const struct pci_device_id *ent) 354 { 355 debugf0("%s()\n", __func__); 356 357 /* don't need to call pci_enable_device() */ 358 return r82600_probe1(pdev, ent->driver_data); 359 } 360 361 static void __devexit r82600_remove_one(struct pci_dev *pdev) 362 { 363 struct mem_ctl_info *mci; 364 365 debugf0("%s()\n", __func__); 366 367 if (r82600_pci) 368 edac_pci_release_generic_ctl(r82600_pci); 369 370 if ((mci = edac_mc_del_mc(&pdev->dev)) == NULL) 371 return; 372 373 edac_mc_free(mci); 374 } 375 376 static DEFINE_PCI_DEVICE_TABLE(r82600_pci_tbl) = { 377 { 378 PCI_DEVICE(PCI_VENDOR_ID_RADISYS, R82600_BRIDGE_ID) 379 }, 380 { 381 0, 382 } /* 0 terminated list. */ 383 }; 384 385 MODULE_DEVICE_TABLE(pci, r82600_pci_tbl); 386 387 static struct pci_driver r82600_driver = { 388 .name = EDAC_MOD_STR, 389 .probe = r82600_init_one, 390 .remove = __devexit_p(r82600_remove_one), 391 .id_table = r82600_pci_tbl, 392 }; 393 394 static int __init r82600_init(void) 395 { 396 /* Ensure that the OPSTATE is set correctly for POLL or NMI */ 397 opstate_init(); 398 399 return pci_register_driver(&r82600_driver); 400 } 401 402 static void __exit r82600_exit(void) 403 { 404 pci_unregister_driver(&r82600_driver); 405 } 406 407 module_init(r82600_init); 408 module_exit(r82600_exit); 409 410 MODULE_LICENSE("GPL"); 411 MODULE_AUTHOR("Tim Small <tim@buttersideup.com> - WPAD Ltd. " 412 "on behalf of EADS Astrium"); 413 MODULE_DESCRIPTION("MC support for Radisys 82600 memory controllers"); 414 415 module_param(disable_hardware_scrub, bool, 0644); 416 MODULE_PARM_DESC(disable_hardware_scrub, 417 "If set, disable the chipset's automatic scrub for CEs"); 418 419 module_param(edac_op_state, int, 0444); 420 MODULE_PARM_DESC(edac_op_state, "EDAC Error Reporting state: 0=Poll,1=NMI"); 421