xref: /openbmc/linux/drivers/crypto/caam/regs.h (revision 0d456bad)
1 /*
2  * CAAM hardware register-level view
3  *
4  * Copyright 2008-2011 Freescale Semiconductor, Inc.
5  */
6 
7 #ifndef REGS_H
8 #define REGS_H
9 
10 #include <linux/types.h>
11 #include <linux/io.h>
12 
13 /*
14  * Architecture-specific register access methods
15  *
16  * CAAM's bus-addressable registers are 64 bits internally.
17  * They have been wired to be safely accessible on 32-bit
18  * architectures, however. Registers were organized such
19  * that (a) they can be contained in 32 bits, (b) if not, then they
20  * can be treated as two 32-bit entities, or finally (c) if they
21  * must be treated as a single 64-bit value, then this can safely
22  * be done with two 32-bit cycles.
23  *
24  * For 32-bit operations on 64-bit values, CAAM follows the same
25  * 64-bit register access conventions as it's predecessors, in that
26  * writes are "triggered" by a write to the register at the numerically
27  * higher address, thus, a full 64-bit write cycle requires a write
28  * to the lower address, followed by a write to the higher address,
29  * which will latch/execute the write cycle.
30  *
31  * For example, let's assume a SW reset of CAAM through the master
32  * configuration register.
33  * - SWRST is in bit 31 of MCFG.
34  * - MCFG begins at base+0x0000.
35  * - Bits 63-32 are a 32-bit word at base+0x0000 (numerically-lower)
36  * - Bits 31-0 are a 32-bit word at base+0x0004 (numerically-higher)
37  *
38  * (and on Power, the convention is 0-31, 32-63, I know...)
39  *
40  * Assuming a 64-bit write to this MCFG to perform a software reset
41  * would then require a write of 0 to base+0x0000, followed by a
42  * write of 0x80000000 to base+0x0004, which would "execute" the
43  * reset.
44  *
45  * Of course, since MCFG 63-32 is all zero, we could cheat and simply
46  * write 0x8000000 to base+0x0004, and the reset would work fine.
47  * However, since CAAM does contain some write-and-read-intended
48  * 64-bit registers, this code defines 64-bit access methods for
49  * the sake of internal consistency and simplicity, and so that a
50  * clean transition to 64-bit is possible when it becomes necessary.
51  *
52  * There are limitations to this that the developer must recognize.
53  * 32-bit architectures cannot enforce an atomic-64 operation,
54  * Therefore:
55  *
56  * - On writes, since the HW is assumed to latch the cycle on the
57  *   write of the higher-numeric-address word, then ordered
58  *   writes work OK.
59  *
60  * - For reads, where a register contains a relevant value of more
61  *   that 32 bits, the hardware employs logic to latch the other
62  *   "half" of the data until read, ensuring an accurate value.
63  *   This is of particular relevance when dealing with CAAM's
64  *   performance counters.
65  *
66  */
67 
68 #ifdef __BIG_ENDIAN
69 #define wr_reg32(reg, data) out_be32(reg, data)
70 #define rd_reg32(reg) in_be32(reg)
71 #ifdef CONFIG_64BIT
72 #define wr_reg64(reg, data) out_be64(reg, data)
73 #define rd_reg64(reg) in_be64(reg)
74 #endif
75 #else
76 #ifdef __LITTLE_ENDIAN
77 #define wr_reg32(reg, data) __raw_writel(reg, data)
78 #define rd_reg32(reg) __raw_readl(reg)
79 #ifdef CONFIG_64BIT
80 #define wr_reg64(reg, data) __raw_writeq(reg, data)
81 #define rd_reg64(reg) __raw_readq(reg)
82 #endif
83 #endif
84 #endif
85 
86 #ifndef CONFIG_64BIT
87 static inline void wr_reg64(u64 __iomem *reg, u64 data)
88 {
89 	wr_reg32((u32 __iomem *)reg, (data & 0xffffffff00000000ull) >> 32);
90 	wr_reg32((u32 __iomem *)reg + 1, data & 0x00000000ffffffffull);
91 }
92 
93 static inline u64 rd_reg64(u64 __iomem *reg)
94 {
95 	return (((u64)rd_reg32((u32 __iomem *)reg)) << 32) |
96 		((u64)rd_reg32((u32 __iomem *)reg + 1));
97 }
98 #endif
99 
100 /*
101  * jr_outentry
102  * Represents each entry in a JobR output ring
103  */
104 struct jr_outentry {
105 	dma_addr_t desc;/* Pointer to completed descriptor */
106 	u32 jrstatus;	/* Status for completed descriptor */
107 } __packed;
108 
109 /*
110  * caam_perfmon - Performance Monitor/Secure Memory Status/
111  *                CAAM Global Status/Component Version IDs
112  *
113  * Spans f00-fff wherever instantiated
114  */
115 
116 /* Number of DECOs */
117 #define CHA_NUM_DECONUM_SHIFT	56
118 #define CHA_NUM_DECONUM_MASK	(0xfull << CHA_NUM_DECONUM_SHIFT)
119 
120 struct sec_vid {
121 	u16 ip_id;
122 	u8 maj_rev;
123 	u8 min_rev;
124 };
125 
126 struct caam_perfmon {
127 	/* Performance Monitor Registers			f00-f9f */
128 	u64 req_dequeued;	/* PC_REQ_DEQ - Dequeued Requests	     */
129 	u64 ob_enc_req;	/* PC_OB_ENC_REQ - Outbound Encrypt Requests */
130 	u64 ib_dec_req;	/* PC_IB_DEC_REQ - Inbound Decrypt Requests  */
131 	u64 ob_enc_bytes;	/* PC_OB_ENCRYPT - Outbound Bytes Encrypted  */
132 	u64 ob_prot_bytes;	/* PC_OB_PROTECT - Outbound Bytes Protected  */
133 	u64 ib_dec_bytes;	/* PC_IB_DECRYPT - Inbound Bytes Decrypted   */
134 	u64 ib_valid_bytes;	/* PC_IB_VALIDATED Inbound Bytes Validated   */
135 	u64 rsvd[13];
136 
137 	/* CAAM Hardware Instantiation Parameters		fa0-fbf */
138 	u64 cha_rev;		/* CRNR - CHA Revision Number		*/
139 #define CTPR_QI_SHIFT		57
140 #define CTPR_QI_MASK		(0x1ull << CTPR_QI_SHIFT)
141 	u64 comp_parms;	/* CTPR - Compile Parameters Register	*/
142 	u64 rsvd1[2];
143 
144 	/* CAAM Global Status					fc0-fdf */
145 	u64 faultaddr;	/* FAR  - Fault Address		*/
146 	u32 faultliodn;	/* FALR - Fault Address LIODN	*/
147 	u32 faultdetail;	/* FADR - Fault Addr Detail	*/
148 	u32 rsvd2;
149 	u32 status;		/* CSTA - CAAM Status */
150 	u64 rsvd3;
151 
152 	/* Component Instantiation Parameters			fe0-fff */
153 	u32 rtic_id;		/* RVID - RTIC Version ID	*/
154 	u32 ccb_id;		/* CCBVID - CCB Version ID	*/
155 	u64 cha_id;		/* CHAVID - CHA Version ID	*/
156 	u64 cha_num;		/* CHANUM - CHA Number		*/
157 	u64 caam_id;		/* CAAMVID - CAAM Version ID	*/
158 };
159 
160 /* LIODN programming for DMA configuration */
161 #define MSTRID_LOCK_LIODN	0x80000000
162 #define MSTRID_LOCK_MAKETRUSTED	0x00010000	/* only for JR masterid */
163 
164 #define MSTRID_LIODN_MASK	0x0fff
165 struct masterid {
166 	u32 liodn_ms;	/* lock and make-trusted control bits */
167 	u32 liodn_ls;	/* LIODN for non-sequence and seq access */
168 };
169 
170 /* Partition ID for DMA configuration */
171 struct partid {
172 	u32 rsvd1;
173 	u32 pidr;	/* partition ID, DECO */
174 };
175 
176 /* RNGB test mode (replicated twice in some configurations) */
177 /* Padded out to 0x100 */
178 struct rngtst {
179 	u32 mode;		/* RTSTMODEx - Test mode */
180 	u32 rsvd1[3];
181 	u32 reset;		/* RTSTRESETx - Test reset control */
182 	u32 rsvd2[3];
183 	u32 status;		/* RTSTSSTATUSx - Test status */
184 	u32 rsvd3;
185 	u32 errstat;		/* RTSTERRSTATx - Test error status */
186 	u32 rsvd4;
187 	u32 errctl;		/* RTSTERRCTLx - Test error control */
188 	u32 rsvd5;
189 	u32 entropy;		/* RTSTENTROPYx - Test entropy */
190 	u32 rsvd6[15];
191 	u32 verifctl;	/* RTSTVERIFCTLx - Test verification control */
192 	u32 rsvd7;
193 	u32 verifstat;	/* RTSTVERIFSTATx - Test verification status */
194 	u32 rsvd8;
195 	u32 verifdata;	/* RTSTVERIFDx - Test verification data */
196 	u32 rsvd9;
197 	u32 xkey;		/* RTSTXKEYx - Test XKEY */
198 	u32 rsvd10;
199 	u32 oscctctl;	/* RTSTOSCCTCTLx - Test osc. counter control */
200 	u32 rsvd11;
201 	u32 oscct;		/* RTSTOSCCTx - Test oscillator counter */
202 	u32 rsvd12;
203 	u32 oscctstat;	/* RTSTODCCTSTATx - Test osc counter status */
204 	u32 rsvd13[2];
205 	u32 ofifo[4];	/* RTSTOFIFOx - Test output FIFO */
206 	u32 rsvd14[15];
207 };
208 
209 /* RNG4 TRNG test registers */
210 struct rng4tst {
211 #define RTMCTL_PRGM 0x00010000	/* 1 -> program mode, 0 -> run mode */
212 	u32 rtmctl;		/* misc. control register */
213 	u32 rtscmisc;		/* statistical check misc. register */
214 	u32 rtpkrrng;		/* poker range register */
215 	union {
216 		u32 rtpkrmax;	/* PRGM=1: poker max. limit register */
217 		u32 rtpkrsq;	/* PRGM=0: poker square calc. result register */
218 	};
219 #define RTSDCTL_ENT_DLY_SHIFT 16
220 #define RTSDCTL_ENT_DLY_MASK (0xffff << RTSDCTL_ENT_DLY_SHIFT)
221 	u32 rtsdctl;		/* seed control register */
222 	union {
223 		u32 rtsblim;	/* PRGM=1: sparse bit limit register */
224 		u32 rttotsam;	/* PRGM=0: total samples register */
225 	};
226 	u32 rtfrqmin;		/* frequency count min. limit register */
227 	union {
228 		u32 rtfrqmax;	/* PRGM=1: freq. count max. limit register */
229 		u32 rtfrqcnt;	/* PRGM=0: freq. count register */
230 	};
231 	u32 rsvd1[56];
232 };
233 
234 /*
235  * caam_ctrl - basic core configuration
236  * starts base + 0x0000 padded out to 0x1000
237  */
238 
239 #define KEK_KEY_SIZE		8
240 #define TKEK_KEY_SIZE		8
241 #define TDSK_KEY_SIZE		8
242 
243 #define DECO_RESET	1	/* Use with DECO reset/availability regs */
244 #define DECO_RESET_0	(DECO_RESET << 0)
245 #define DECO_RESET_1	(DECO_RESET << 1)
246 #define DECO_RESET_2	(DECO_RESET << 2)
247 #define DECO_RESET_3	(DECO_RESET << 3)
248 #define DECO_RESET_4	(DECO_RESET << 4)
249 
250 struct caam_ctrl {
251 	/* Basic Configuration Section				000-01f */
252 	/* Read/Writable					        */
253 	u32 rsvd1;
254 	u32 mcr;		/* MCFG      Master Config Register  */
255 	u32 rsvd2[2];
256 
257 	/* Bus Access Configuration Section			010-11f */
258 	/* Read/Writable                                                */
259 	struct masterid jr_mid[4];	/* JRxLIODNR - JobR LIODN setup */
260 	u32 rsvd3[12];
261 	struct masterid rtic_mid[4];	/* RTICxLIODNR - RTIC LIODN setup */
262 	u32 rsvd4[7];
263 	u32 deco_rq;			/* DECORR - DECO Request */
264 	struct partid deco_mid[5];	/* DECOxLIODNR - 1 per DECO */
265 	u32 rsvd5[22];
266 
267 	/* DECO Availability/Reset Section			120-3ff */
268 	u32 deco_avail;		/* DAR - DECO availability */
269 	u32 deco_reset;		/* DRR - DECO reset */
270 	u32 rsvd6[182];
271 
272 	/* Key Encryption/Decryption Configuration              400-5ff */
273 	/* Read/Writable only while in Non-secure mode                  */
274 	u32 kek[KEK_KEY_SIZE];	/* JDKEKR - Key Encryption Key */
275 	u32 tkek[TKEK_KEY_SIZE];	/* TDKEKR - Trusted Desc KEK */
276 	u32 tdsk[TDSK_KEY_SIZE];	/* TDSKR - Trusted Desc Signing Key */
277 	u32 rsvd7[32];
278 	u64 sknonce;			/* SKNR - Secure Key Nonce */
279 	u32 rsvd8[70];
280 
281 	/* RNG Test/Verification/Debug Access                   600-7ff */
282 	/* (Useful in Test/Debug modes only...)                         */
283 	union {
284 		struct rngtst rtst[2];
285 		struct rng4tst r4tst[2];
286 	};
287 
288 	u32 rsvd9[448];
289 
290 	/* Performance Monitor                                  f00-fff */
291 	struct caam_perfmon perfmon;
292 };
293 
294 /*
295  * Controller master config register defs
296  */
297 #define MCFGR_SWRESET		0x80000000 /* software reset */
298 #define MCFGR_WDENABLE		0x40000000 /* DECO watchdog enable */
299 #define MCFGR_WDFAIL		0x20000000 /* DECO watchdog force-fail */
300 #define MCFGR_DMA_RESET		0x10000000
301 #define MCFGR_LONG_PTR		0x00010000 /* Use >32-bit desc addressing */
302 
303 /* AXI read cache control */
304 #define MCFGR_ARCACHE_SHIFT	12
305 #define MCFGR_ARCACHE_MASK	(0xf << MCFGR_ARCACHE_SHIFT)
306 
307 /* AXI write cache control */
308 #define MCFGR_AWCACHE_SHIFT	8
309 #define MCFGR_AWCACHE_MASK	(0xf << MCFGR_AWCACHE_SHIFT)
310 
311 /* AXI pipeline depth */
312 #define MCFGR_AXIPIPE_SHIFT	4
313 #define MCFGR_AXIPIPE_MASK	(0xf << MCFGR_AXIPIPE_SHIFT)
314 
315 #define MCFGR_AXIPRI		0x00000008 /* Assert AXI priority sideband */
316 #define MCFGR_BURST_64		0x00000001 /* Max burst size */
317 
318 /*
319  * caam_job_ring - direct job ring setup
320  * 1-4 possible per instantiation, base + 1000/2000/3000/4000
321  * Padded out to 0x1000
322  */
323 struct caam_job_ring {
324 	/* Input ring */
325 	u64 inpring_base;	/* IRBAx -  Input desc ring baseaddr */
326 	u32 rsvd1;
327 	u32 inpring_size;	/* IRSx - Input ring size */
328 	u32 rsvd2;
329 	u32 inpring_avail;	/* IRSAx - Input ring room remaining */
330 	u32 rsvd3;
331 	u32 inpring_jobadd;	/* IRJAx - Input ring jobs added */
332 
333 	/* Output Ring */
334 	u64 outring_base;	/* ORBAx - Output status ring base addr */
335 	u32 rsvd4;
336 	u32 outring_size;	/* ORSx - Output ring size */
337 	u32 rsvd5;
338 	u32 outring_rmvd;	/* ORJRx - Output ring jobs removed */
339 	u32 rsvd6;
340 	u32 outring_used;	/* ORSFx - Output ring slots full */
341 
342 	/* Status/Configuration */
343 	u32 rsvd7;
344 	u32 jroutstatus;	/* JRSTAx - JobR output status */
345 	u32 rsvd8;
346 	u32 jrintstatus;	/* JRINTx - JobR interrupt status */
347 	u32 rconfig_hi;	/* JRxCFG - Ring configuration */
348 	u32 rconfig_lo;
349 
350 	/* Indices. CAAM maintains as "heads" of each queue */
351 	u32 rsvd9;
352 	u32 inp_rdidx;	/* IRRIx - Input ring read index */
353 	u32 rsvd10;
354 	u32 out_wtidx;	/* ORWIx - Output ring write index */
355 
356 	/* Command/control */
357 	u32 rsvd11;
358 	u32 jrcommand;	/* JRCRx - JobR command */
359 
360 	u32 rsvd12[932];
361 
362 	/* Performance Monitor                                  f00-fff */
363 	struct caam_perfmon perfmon;
364 };
365 
366 #define JR_RINGSIZE_MASK	0x03ff
367 /*
368  * jrstatus - Job Ring Output Status
369  * All values in lo word
370  * Also note, same values written out as status through QI
371  * in the command/status field of a frame descriptor
372  */
373 #define JRSTA_SSRC_SHIFT            28
374 #define JRSTA_SSRC_MASK             0xf0000000
375 
376 #define JRSTA_SSRC_NONE             0x00000000
377 #define JRSTA_SSRC_CCB_ERROR        0x20000000
378 #define JRSTA_SSRC_JUMP_HALT_USER   0x30000000
379 #define JRSTA_SSRC_DECO             0x40000000
380 #define JRSTA_SSRC_JRERROR          0x60000000
381 #define JRSTA_SSRC_JUMP_HALT_CC     0x70000000
382 
383 #define JRSTA_DECOERR_JUMP          0x08000000
384 #define JRSTA_DECOERR_INDEX_SHIFT   8
385 #define JRSTA_DECOERR_INDEX_MASK    0xff00
386 #define JRSTA_DECOERR_ERROR_MASK    0x00ff
387 
388 #define JRSTA_DECOERR_NONE          0x00
389 #define JRSTA_DECOERR_LINKLEN       0x01
390 #define JRSTA_DECOERR_LINKPTR       0x02
391 #define JRSTA_DECOERR_JRCTRL        0x03
392 #define JRSTA_DECOERR_DESCCMD       0x04
393 #define JRSTA_DECOERR_ORDER         0x05
394 #define JRSTA_DECOERR_KEYCMD        0x06
395 #define JRSTA_DECOERR_LOADCMD       0x07
396 #define JRSTA_DECOERR_STORECMD      0x08
397 #define JRSTA_DECOERR_OPCMD         0x09
398 #define JRSTA_DECOERR_FIFOLDCMD     0x0a
399 #define JRSTA_DECOERR_FIFOSTCMD     0x0b
400 #define JRSTA_DECOERR_MOVECMD       0x0c
401 #define JRSTA_DECOERR_JUMPCMD       0x0d
402 #define JRSTA_DECOERR_MATHCMD       0x0e
403 #define JRSTA_DECOERR_SHASHCMD      0x0f
404 #define JRSTA_DECOERR_SEQCMD        0x10
405 #define JRSTA_DECOERR_DECOINTERNAL  0x11
406 #define JRSTA_DECOERR_SHDESCHDR     0x12
407 #define JRSTA_DECOERR_HDRLEN        0x13
408 #define JRSTA_DECOERR_BURSTER       0x14
409 #define JRSTA_DECOERR_DESCSIGNATURE 0x15
410 #define JRSTA_DECOERR_DMA           0x16
411 #define JRSTA_DECOERR_BURSTFIFO     0x17
412 #define JRSTA_DECOERR_JRRESET       0x1a
413 #define JRSTA_DECOERR_JOBFAIL       0x1b
414 #define JRSTA_DECOERR_DNRERR        0x80
415 #define JRSTA_DECOERR_UNDEFPCL      0x81
416 #define JRSTA_DECOERR_PDBERR        0x82
417 #define JRSTA_DECOERR_ANRPLY_LATE   0x83
418 #define JRSTA_DECOERR_ANRPLY_REPLAY 0x84
419 #define JRSTA_DECOERR_SEQOVF        0x85
420 #define JRSTA_DECOERR_INVSIGN       0x86
421 #define JRSTA_DECOERR_DSASIGN       0x87
422 
423 #define JRSTA_CCBERR_JUMP           0x08000000
424 #define JRSTA_CCBERR_INDEX_MASK     0xff00
425 #define JRSTA_CCBERR_INDEX_SHIFT    8
426 #define JRSTA_CCBERR_CHAID_MASK     0x00f0
427 #define JRSTA_CCBERR_CHAID_SHIFT    4
428 #define JRSTA_CCBERR_ERRID_MASK     0x000f
429 
430 #define JRSTA_CCBERR_CHAID_AES      (0x01 << JRSTA_CCBERR_CHAID_SHIFT)
431 #define JRSTA_CCBERR_CHAID_DES      (0x02 << JRSTA_CCBERR_CHAID_SHIFT)
432 #define JRSTA_CCBERR_CHAID_ARC4     (0x03 << JRSTA_CCBERR_CHAID_SHIFT)
433 #define JRSTA_CCBERR_CHAID_MD       (0x04 << JRSTA_CCBERR_CHAID_SHIFT)
434 #define JRSTA_CCBERR_CHAID_RNG      (0x05 << JRSTA_CCBERR_CHAID_SHIFT)
435 #define JRSTA_CCBERR_CHAID_SNOW     (0x06 << JRSTA_CCBERR_CHAID_SHIFT)
436 #define JRSTA_CCBERR_CHAID_KASUMI   (0x07 << JRSTA_CCBERR_CHAID_SHIFT)
437 #define JRSTA_CCBERR_CHAID_PK       (0x08 << JRSTA_CCBERR_CHAID_SHIFT)
438 #define JRSTA_CCBERR_CHAID_CRC      (0x09 << JRSTA_CCBERR_CHAID_SHIFT)
439 
440 #define JRSTA_CCBERR_ERRID_NONE     0x00
441 #define JRSTA_CCBERR_ERRID_MODE     0x01
442 #define JRSTA_CCBERR_ERRID_DATASIZ  0x02
443 #define JRSTA_CCBERR_ERRID_KEYSIZ   0x03
444 #define JRSTA_CCBERR_ERRID_PKAMEMSZ 0x04
445 #define JRSTA_CCBERR_ERRID_PKBMEMSZ 0x05
446 #define JRSTA_CCBERR_ERRID_SEQUENCE 0x06
447 #define JRSTA_CCBERR_ERRID_PKDIVZRO 0x07
448 #define JRSTA_CCBERR_ERRID_PKMODEVN 0x08
449 #define JRSTA_CCBERR_ERRID_KEYPARIT 0x09
450 #define JRSTA_CCBERR_ERRID_ICVCHK   0x0a
451 #define JRSTA_CCBERR_ERRID_HARDWARE 0x0b
452 #define JRSTA_CCBERR_ERRID_CCMAAD   0x0c
453 #define JRSTA_CCBERR_ERRID_INVCHA   0x0f
454 
455 #define JRINT_ERR_INDEX_MASK        0x3fff0000
456 #define JRINT_ERR_INDEX_SHIFT       16
457 #define JRINT_ERR_TYPE_MASK         0xf00
458 #define JRINT_ERR_TYPE_SHIFT        8
459 #define JRINT_ERR_HALT_MASK         0xc
460 #define JRINT_ERR_HALT_SHIFT        2
461 #define JRINT_ERR_HALT_INPROGRESS   0x4
462 #define JRINT_ERR_HALT_COMPLETE     0x8
463 #define JRINT_JR_ERROR              0x02
464 #define JRINT_JR_INT                0x01
465 
466 #define JRINT_ERR_TYPE_WRITE        1
467 #define JRINT_ERR_TYPE_BAD_INPADDR  3
468 #define JRINT_ERR_TYPE_BAD_OUTADDR  4
469 #define JRINT_ERR_TYPE_INV_INPWRT   5
470 #define JRINT_ERR_TYPE_INV_OUTWRT   6
471 #define JRINT_ERR_TYPE_RESET        7
472 #define JRINT_ERR_TYPE_REMOVE_OFL   8
473 #define JRINT_ERR_TYPE_ADD_OFL      9
474 
475 #define JRCFG_SOE		0x04
476 #define JRCFG_ICEN		0x02
477 #define JRCFG_IMSK		0x01
478 #define JRCFG_ICDCT_SHIFT	8
479 #define JRCFG_ICTT_SHIFT	16
480 
481 #define JRCR_RESET                  0x01
482 
483 /*
484  * caam_assurance - Assurance Controller View
485  * base + 0x6000 padded out to 0x1000
486  */
487 
488 struct rtic_element {
489 	u64 address;
490 	u32 rsvd;
491 	u32 length;
492 };
493 
494 struct rtic_block {
495 	struct rtic_element element[2];
496 };
497 
498 struct rtic_memhash {
499 	u32 memhash_be[32];
500 	u32 memhash_le[32];
501 };
502 
503 struct caam_assurance {
504     /* Status/Command/Watchdog */
505 	u32 rsvd1;
506 	u32 status;		/* RSTA - Status */
507 	u32 rsvd2;
508 	u32 cmd;		/* RCMD - Command */
509 	u32 rsvd3;
510 	u32 ctrl;		/* RCTL - Control */
511 	u32 rsvd4;
512 	u32 throttle;	/* RTHR - Throttle */
513 	u32 rsvd5[2];
514 	u64 watchdog;	/* RWDOG - Watchdog Timer */
515 	u32 rsvd6;
516 	u32 rend;		/* REND - Endian corrections */
517 	u32 rsvd7[50];
518 
519 	/* Block access/configuration @ 100/110/120/130 */
520 	struct rtic_block memblk[4];	/* Memory Blocks A-D */
521 	u32 rsvd8[32];
522 
523 	/* Block hashes @ 200/300/400/500 */
524 	struct rtic_memhash hash[4];	/* Block hash values A-D */
525 	u32 rsvd_3[640];
526 };
527 
528 /*
529  * caam_queue_if - QI configuration and control
530  * starts base + 0x7000, padded out to 0x1000 long
531  */
532 
533 struct caam_queue_if {
534 	u32 qi_control_hi;	/* QICTL  - QI Control */
535 	u32 qi_control_lo;
536 	u32 rsvd1;
537 	u32 qi_status;	/* QISTA  - QI Status */
538 	u32 qi_deq_cfg_hi;	/* QIDQC  - QI Dequeue Configuration */
539 	u32 qi_deq_cfg_lo;
540 	u32 qi_enq_cfg_hi;	/* QISEQC - QI Enqueue Command     */
541 	u32 qi_enq_cfg_lo;
542 	u32 rsvd2[1016];
543 };
544 
545 /* QI control bits - low word */
546 #define QICTL_DQEN      0x01              /* Enable frame pop          */
547 #define QICTL_STOP      0x02              /* Stop dequeue/enqueue      */
548 #define QICTL_SOE       0x04              /* Stop on error             */
549 
550 /* QI control bits - high word */
551 #define QICTL_MBSI	0x01
552 #define QICTL_MHWSI	0x02
553 #define QICTL_MWSI	0x04
554 #define QICTL_MDWSI	0x08
555 #define QICTL_CBSI	0x10		/* CtrlDataByteSwapInput     */
556 #define QICTL_CHWSI	0x20		/* CtrlDataHalfSwapInput     */
557 #define QICTL_CWSI	0x40		/* CtrlDataWordSwapInput     */
558 #define QICTL_CDWSI	0x80		/* CtrlDataDWordSwapInput    */
559 #define QICTL_MBSO	0x0100
560 #define QICTL_MHWSO	0x0200
561 #define QICTL_MWSO	0x0400
562 #define QICTL_MDWSO	0x0800
563 #define QICTL_CBSO	0x1000		/* CtrlDataByteSwapOutput    */
564 #define QICTL_CHWSO	0x2000		/* CtrlDataHalfSwapOutput    */
565 #define QICTL_CWSO	0x4000		/* CtrlDataWordSwapOutput    */
566 #define QICTL_CDWSO     0x8000		/* CtrlDataDWordSwapOutput   */
567 #define QICTL_DMBS	0x010000
568 #define QICTL_EPO	0x020000
569 
570 /* QI status bits */
571 #define QISTA_PHRDERR   0x01              /* PreHeader Read Error      */
572 #define QISTA_CFRDERR   0x02              /* Compound Frame Read Error */
573 #define QISTA_OFWRERR   0x04              /* Output Frame Read Error   */
574 #define QISTA_BPDERR    0x08              /* Buffer Pool Depleted      */
575 #define QISTA_BTSERR    0x10              /* Buffer Undersize          */
576 #define QISTA_CFWRERR   0x20              /* Compound Frame Write Err  */
577 #define QISTA_STOPD     0x80000000        /* QI Stopped (see QICTL)    */
578 
579 /* deco_sg_table - DECO view of scatter/gather table */
580 struct deco_sg_table {
581 	u64 addr;		/* Segment Address */
582 	u32 elen;		/* E, F bits + 30-bit length */
583 	u32 bpid_offset;	/* Buffer Pool ID + 16-bit length */
584 };
585 
586 /*
587  * caam_deco - descriptor controller - CHA cluster block
588  *
589  * Only accessible when direct DECO access is turned on
590  * (done in DECORR, via MID programmed in DECOxMID
591  *
592  * 5 typical, base + 0x8000/9000/a000/b000
593  * Padded out to 0x1000 long
594  */
595 struct caam_deco {
596 	u32 rsvd1;
597 	u32 cls1_mode;	/* CxC1MR -  Class 1 Mode */
598 	u32 rsvd2;
599 	u32 cls1_keysize;	/* CxC1KSR - Class 1 Key Size */
600 	u32 cls1_datasize_hi;	/* CxC1DSR - Class 1 Data Size */
601 	u32 cls1_datasize_lo;
602 	u32 rsvd3;
603 	u32 cls1_icvsize;	/* CxC1ICVSR - Class 1 ICV size */
604 	u32 rsvd4[5];
605 	u32 cha_ctrl;	/* CCTLR - CHA control */
606 	u32 rsvd5;
607 	u32 irq_crtl;	/* CxCIRQ - CCB interrupt done/error/clear */
608 	u32 rsvd6;
609 	u32 clr_written;	/* CxCWR - Clear-Written */
610 	u32 ccb_status_hi;	/* CxCSTA - CCB Status/Error */
611 	u32 ccb_status_lo;
612 	u32 rsvd7[3];
613 	u32 aad_size;	/* CxAADSZR - Current AAD Size */
614 	u32 rsvd8;
615 	u32 cls1_iv_size;	/* CxC1IVSZR - Current Class 1 IV Size */
616 	u32 rsvd9[7];
617 	u32 pkha_a_size;	/* PKASZRx - Size of PKHA A */
618 	u32 rsvd10;
619 	u32 pkha_b_size;	/* PKBSZRx - Size of PKHA B */
620 	u32 rsvd11;
621 	u32 pkha_n_size;	/* PKNSZRx - Size of PKHA N */
622 	u32 rsvd12;
623 	u32 pkha_e_size;	/* PKESZRx - Size of PKHA E */
624 	u32 rsvd13[24];
625 	u32 cls1_ctx[16];	/* CxC1CTXR - Class 1 Context @100 */
626 	u32 rsvd14[48];
627 	u32 cls1_key[8];	/* CxC1KEYR - Class 1 Key @200 */
628 	u32 rsvd15[121];
629 	u32 cls2_mode;	/* CxC2MR - Class 2 Mode */
630 	u32 rsvd16;
631 	u32 cls2_keysize;	/* CxX2KSR - Class 2 Key Size */
632 	u32 cls2_datasize_hi;	/* CxC2DSR - Class 2 Data Size */
633 	u32 cls2_datasize_lo;
634 	u32 rsvd17;
635 	u32 cls2_icvsize;	/* CxC2ICVSZR - Class 2 ICV Size */
636 	u32 rsvd18[56];
637 	u32 cls2_ctx[18];	/* CxC2CTXR - Class 2 Context @500 */
638 	u32 rsvd19[46];
639 	u32 cls2_key[32];	/* CxC2KEYR - Class2 Key @600 */
640 	u32 rsvd20[84];
641 	u32 inp_infofifo_hi;	/* CxIFIFO - Input Info FIFO @7d0 */
642 	u32 inp_infofifo_lo;
643 	u32 rsvd21[2];
644 	u64 inp_datafifo;	/* CxDFIFO - Input Data FIFO */
645 	u32 rsvd22[2];
646 	u64 out_datafifo;	/* CxOFIFO - Output Data FIFO */
647 	u32 rsvd23[2];
648 	u32 jr_ctl_hi;	/* CxJRR - JobR Control Register      @800 */
649 	u32 jr_ctl_lo;
650 	u64 jr_descaddr;	/* CxDADR - JobR Descriptor Address */
651 	u32 op_status_hi;	/* DxOPSTA - DECO Operation Status */
652 	u32 op_status_lo;
653 	u32 rsvd24[2];
654 	u32 liodn;		/* DxLSR - DECO LIODN Status - non-seq */
655 	u32 td_liodn;	/* DxLSR - DECO LIODN Status - trustdesc */
656 	u32 rsvd26[6];
657 	u64 math[4];		/* DxMTH - Math register */
658 	u32 rsvd27[8];
659 	struct deco_sg_table gthr_tbl[4];	/* DxGTR - Gather Tables */
660 	u32 rsvd28[16];
661 	struct deco_sg_table sctr_tbl[4];	/* DxSTR - Scatter Tables */
662 	u32 rsvd29[48];
663 	u32 descbuf[64];	/* DxDESB - Descriptor buffer */
664 	u32 rsvd30[320];
665 };
666 
667 /*
668  * Current top-level view of memory map is:
669  *
670  * 0x0000 - 0x0fff - CAAM Top-Level Control
671  * 0x1000 - 0x1fff - Job Ring 0
672  * 0x2000 - 0x2fff - Job Ring 1
673  * 0x3000 - 0x3fff - Job Ring 2
674  * 0x4000 - 0x4fff - Job Ring 3
675  * 0x5000 - 0x5fff - (unused)
676  * 0x6000 - 0x6fff - Assurance Controller
677  * 0x7000 - 0x7fff - Queue Interface
678  * 0x8000 - 0x8fff - DECO-CCB 0
679  * 0x9000 - 0x9fff - DECO-CCB 1
680  * 0xa000 - 0xafff - DECO-CCB 2
681  * 0xb000 - 0xbfff - DECO-CCB 3
682  * 0xc000 - 0xcfff - DECO-CCB 4
683  *
684  * caam_full describes the full register view of CAAM if useful,
685  * although many configurations may choose to implement parts of
686  * the register map separately, in differing privilege regions
687  */
688 struct caam_full {
689 	struct caam_ctrl __iomem ctrl;
690 	struct caam_job_ring jr[4];
691 	u64 rsvd[512];
692 	struct caam_assurance assure;
693 	struct caam_queue_if qi;
694 };
695 
696 #endif /* REGS_H */
697