1 // SPDX-License-Identifier: GPL-2.0
2 /*
3 * Driver for Silicon Labs Si544 Programmable Oscillator
4 * Copyright (C) 2018 Topic Embedded Products
5 * Author: Mike Looijmans <mike.looijmans@topic.nl>
6 */
7
8 #include <linux/clk-provider.h>
9 #include <linux/delay.h>
10 #include <linux/math64.h>
11 #include <linux/module.h>
12 #include <linux/i2c.h>
13 #include <linux/regmap.h>
14 #include <linux/slab.h>
15
16 /* I2C registers (decimal as in datasheet) */
17 #define SI544_REG_CONTROL 7
18 #define SI544_REG_OE_STATE 17
19 #define SI544_REG_HS_DIV 23
20 #define SI544_REG_LS_HS_DIV 24
21 #define SI544_REG_FBDIV0 26
22 #define SI544_REG_FBDIV8 27
23 #define SI544_REG_FBDIV16 28
24 #define SI544_REG_FBDIV24 29
25 #define SI544_REG_FBDIV32 30
26 #define SI544_REG_FBDIV40 31
27 #define SI544_REG_FCAL_OVR 69
28 #define SI544_REG_ADPLL_DELTA_M0 231
29 #define SI544_REG_ADPLL_DELTA_M8 232
30 #define SI544_REG_ADPLL_DELTA_M16 233
31 #define SI544_REG_PAGE_SELECT 255
32
33 /* Register values */
34 #define SI544_CONTROL_RESET BIT(7)
35 #define SI544_CONTROL_MS_ICAL2 BIT(3)
36
37 #define SI544_OE_STATE_ODC_OE BIT(0)
38
39 /* Max freq depends on speed grade */
40 #define SI544_MIN_FREQ 200000U
41
42 /* Si544 Internal oscilator runs at 55.05 MHz */
43 #define FXO 55050000U
44
45 /* VCO range is 10.8 .. 12.1 GHz, max depends on speed grade */
46 #define FVCO_MIN 10800000000ULL
47
48 #define HS_DIV_MAX 2046
49 #define HS_DIV_MAX_ODD 33
50
51 /* Lowest frequency synthesizeable using only the HS divider */
52 #define MIN_HSDIV_FREQ (FVCO_MIN / HS_DIV_MAX)
53
54 /* Range and interpretation of the adjustment value */
55 #define DELTA_M_MAX 8161512
56 #define DELTA_M_FRAC_NUM 19
57 #define DELTA_M_FRAC_DEN 20000
58
59 enum si544_speed_grade {
60 si544a,
61 si544b,
62 si544c,
63 };
64
65 struct clk_si544 {
66 struct clk_hw hw;
67 struct regmap *regmap;
68 struct i2c_client *i2c_client;
69 enum si544_speed_grade speed_grade;
70 };
71 #define to_clk_si544(_hw) container_of(_hw, struct clk_si544, hw)
72
73 /**
74 * struct clk_si544_muldiv - Multiplier/divider settings
75 * @fb_div_frac: integer part of feedback divider (32 bits)
76 * @fb_div_int: fractional part of feedback divider (11 bits)
77 * @hs_div: 1st divider, 5..2046, must be even when >33
78 * @ls_div_bits: 2nd divider, as 2^x, range 0..5
79 * If ls_div_bits is non-zero, hs_div must be even
80 * @delta_m: Frequency shift for small -950..+950 ppm changes, 24 bit
81 */
82 struct clk_si544_muldiv {
83 u32 fb_div_frac;
84 u16 fb_div_int;
85 u16 hs_div;
86 u8 ls_div_bits;
87 s32 delta_m;
88 };
89
90 /* Enables or disables the output driver */
si544_enable_output(struct clk_si544 * data,bool enable)91 static int si544_enable_output(struct clk_si544 *data, bool enable)
92 {
93 return regmap_update_bits(data->regmap, SI544_REG_OE_STATE,
94 SI544_OE_STATE_ODC_OE, enable ? SI544_OE_STATE_ODC_OE : 0);
95 }
96
si544_prepare(struct clk_hw * hw)97 static int si544_prepare(struct clk_hw *hw)
98 {
99 struct clk_si544 *data = to_clk_si544(hw);
100
101 return si544_enable_output(data, true);
102 }
103
si544_unprepare(struct clk_hw * hw)104 static void si544_unprepare(struct clk_hw *hw)
105 {
106 struct clk_si544 *data = to_clk_si544(hw);
107
108 si544_enable_output(data, false);
109 }
110
si544_is_prepared(struct clk_hw * hw)111 static int si544_is_prepared(struct clk_hw *hw)
112 {
113 struct clk_si544 *data = to_clk_si544(hw);
114 unsigned int val;
115 int err;
116
117 err = regmap_read(data->regmap, SI544_REG_OE_STATE, &val);
118 if (err < 0)
119 return err;
120
121 return !!(val & SI544_OE_STATE_ODC_OE);
122 }
123
124 /* Retrieve clock multiplier and dividers from hardware */
si544_get_muldiv(struct clk_si544 * data,struct clk_si544_muldiv * settings)125 static int si544_get_muldiv(struct clk_si544 *data,
126 struct clk_si544_muldiv *settings)
127 {
128 int err;
129 u8 reg[6];
130
131 err = regmap_bulk_read(data->regmap, SI544_REG_HS_DIV, reg, 2);
132 if (err)
133 return err;
134
135 settings->ls_div_bits = (reg[1] >> 4) & 0x07;
136 settings->hs_div = (reg[1] & 0x07) << 8 | reg[0];
137
138 err = regmap_bulk_read(data->regmap, SI544_REG_FBDIV0, reg, 6);
139 if (err)
140 return err;
141
142 settings->fb_div_int = reg[4] | (reg[5] & 0x07) << 8;
143 settings->fb_div_frac = reg[0] | reg[1] << 8 | reg[2] << 16 |
144 reg[3] << 24;
145
146 err = regmap_bulk_read(data->regmap, SI544_REG_ADPLL_DELTA_M0, reg, 3);
147 if (err)
148 return err;
149
150 /* Interpret as 24-bit signed number */
151 settings->delta_m = reg[0] << 8 | reg[1] << 16 | reg[2] << 24;
152 settings->delta_m >>= 8;
153
154 return 0;
155 }
156
si544_set_delta_m(struct clk_si544 * data,s32 delta_m)157 static int si544_set_delta_m(struct clk_si544 *data, s32 delta_m)
158 {
159 u8 reg[3];
160
161 reg[0] = delta_m;
162 reg[1] = delta_m >> 8;
163 reg[2] = delta_m >> 16;
164
165 return regmap_bulk_write(data->regmap, SI544_REG_ADPLL_DELTA_M0,
166 reg, 3);
167 }
168
si544_set_muldiv(struct clk_si544 * data,struct clk_si544_muldiv * settings)169 static int si544_set_muldiv(struct clk_si544 *data,
170 struct clk_si544_muldiv *settings)
171 {
172 int err;
173 u8 reg[6];
174
175 reg[0] = settings->hs_div;
176 reg[1] = settings->hs_div >> 8 | settings->ls_div_bits << 4;
177
178 err = regmap_bulk_write(data->regmap, SI544_REG_HS_DIV, reg, 2);
179 if (err < 0)
180 return err;
181
182 reg[0] = settings->fb_div_frac;
183 reg[1] = settings->fb_div_frac >> 8;
184 reg[2] = settings->fb_div_frac >> 16;
185 reg[3] = settings->fb_div_frac >> 24;
186 reg[4] = settings->fb_div_int;
187 reg[5] = settings->fb_div_int >> 8;
188
189 /*
190 * Writing to SI544_REG_FBDIV40 triggers the clock change, so that
191 * must be written last
192 */
193 return regmap_bulk_write(data->regmap, SI544_REG_FBDIV0, reg, 6);
194 }
195
is_valid_frequency(const struct clk_si544 * data,unsigned long frequency)196 static bool is_valid_frequency(const struct clk_si544 *data,
197 unsigned long frequency)
198 {
199 unsigned long max_freq = 0;
200
201 if (frequency < SI544_MIN_FREQ)
202 return false;
203
204 switch (data->speed_grade) {
205 case si544a:
206 max_freq = 1500000000;
207 break;
208 case si544b:
209 max_freq = 800000000;
210 break;
211 case si544c:
212 max_freq = 350000000;
213 break;
214 }
215
216 return frequency <= max_freq;
217 }
218
219 /* Calculate divider settings for a given frequency */
si544_calc_muldiv(struct clk_si544_muldiv * settings,unsigned long frequency)220 static int si544_calc_muldiv(struct clk_si544_muldiv *settings,
221 unsigned long frequency)
222 {
223 u64 vco;
224 u32 ls_freq;
225 u32 tmp;
226 u8 res;
227
228 /* Determine the minimum value of LS_DIV and resulting target freq. */
229 ls_freq = frequency;
230 settings->ls_div_bits = 0;
231
232 if (frequency >= MIN_HSDIV_FREQ) {
233 settings->ls_div_bits = 0;
234 } else {
235 res = 1;
236 tmp = 2 * HS_DIV_MAX;
237 while (tmp <= (HS_DIV_MAX * 32)) {
238 if (((u64)frequency * tmp) >= FVCO_MIN)
239 break;
240 ++res;
241 tmp <<= 1;
242 }
243 settings->ls_div_bits = res;
244 ls_freq = frequency << res;
245 }
246
247 /* Determine minimum HS_DIV by rounding up */
248 vco = FVCO_MIN + ls_freq - 1;
249 do_div(vco, ls_freq);
250 settings->hs_div = vco;
251
252 /* round up to even number when required */
253 if ((settings->hs_div & 1) &&
254 (settings->hs_div > HS_DIV_MAX_ODD || settings->ls_div_bits))
255 ++settings->hs_div;
256
257 /* Calculate VCO frequency (in 10..12GHz range) */
258 vco = (u64)ls_freq * settings->hs_div;
259
260 /* Calculate the integer part of the feedback divider */
261 tmp = do_div(vco, FXO);
262 settings->fb_div_int = vco;
263
264 /* And the fractional bits using the remainder */
265 vco = (u64)tmp << 32;
266 vco += FXO / 2; /* Round to nearest multiple */
267 do_div(vco, FXO);
268 settings->fb_div_frac = vco;
269
270 /* Reset the frequency adjustment */
271 settings->delta_m = 0;
272
273 return 0;
274 }
275
276 /* Calculate resulting frequency given the register settings */
si544_calc_center_rate(const struct clk_si544_muldiv * settings)277 static unsigned long si544_calc_center_rate(
278 const struct clk_si544_muldiv *settings)
279 {
280 u32 d = settings->hs_div * BIT(settings->ls_div_bits);
281 u64 vco;
282
283 /* Calculate VCO from the fractional part */
284 vco = (u64)settings->fb_div_frac * FXO;
285 vco += (FXO / 2);
286 vco >>= 32;
287
288 /* Add the integer part of the VCO frequency */
289 vco += (u64)settings->fb_div_int * FXO;
290
291 /* Apply divider to obtain the generated frequency */
292 do_div(vco, d);
293
294 return vco;
295 }
296
si544_calc_rate(const struct clk_si544_muldiv * settings)297 static unsigned long si544_calc_rate(const struct clk_si544_muldiv *settings)
298 {
299 unsigned long rate = si544_calc_center_rate(settings);
300 s64 delta = (s64)rate * (DELTA_M_FRAC_NUM * settings->delta_m);
301
302 /*
303 * The clock adjustment is much smaller than 1 Hz, round to the
304 * nearest multiple. Apparently div64_s64 rounds towards zero, hence
305 * check the sign and adjust into the proper direction.
306 */
307 if (settings->delta_m < 0)
308 delta -= ((s64)DELTA_M_MAX * DELTA_M_FRAC_DEN) / 2;
309 else
310 delta += ((s64)DELTA_M_MAX * DELTA_M_FRAC_DEN) / 2;
311 delta = div64_s64(delta, ((s64)DELTA_M_MAX * DELTA_M_FRAC_DEN));
312
313 return rate + delta;
314 }
315
si544_recalc_rate(struct clk_hw * hw,unsigned long parent_rate)316 static unsigned long si544_recalc_rate(struct clk_hw *hw,
317 unsigned long parent_rate)
318 {
319 struct clk_si544 *data = to_clk_si544(hw);
320 struct clk_si544_muldiv settings;
321 int err;
322
323 err = si544_get_muldiv(data, &settings);
324 if (err)
325 return 0;
326
327 return si544_calc_rate(&settings);
328 }
329
si544_round_rate(struct clk_hw * hw,unsigned long rate,unsigned long * parent_rate)330 static long si544_round_rate(struct clk_hw *hw, unsigned long rate,
331 unsigned long *parent_rate)
332 {
333 struct clk_si544 *data = to_clk_si544(hw);
334
335 if (!is_valid_frequency(data, rate))
336 return -EINVAL;
337
338 /* The accuracy is less than 1 Hz, so any rate is possible */
339 return rate;
340 }
341
342 /* Calculates the maximum "small" change, 950 * rate / 1000000 */
si544_max_delta(unsigned long rate)343 static unsigned long si544_max_delta(unsigned long rate)
344 {
345 u64 num = rate;
346
347 num *= DELTA_M_FRAC_NUM;
348 do_div(num, DELTA_M_FRAC_DEN);
349
350 return num;
351 }
352
si544_calc_delta(s32 delta,s32 max_delta)353 static s32 si544_calc_delta(s32 delta, s32 max_delta)
354 {
355 s64 n = (s64)delta * DELTA_M_MAX;
356
357 return div_s64(n, max_delta);
358 }
359
si544_set_rate(struct clk_hw * hw,unsigned long rate,unsigned long parent_rate)360 static int si544_set_rate(struct clk_hw *hw, unsigned long rate,
361 unsigned long parent_rate)
362 {
363 struct clk_si544 *data = to_clk_si544(hw);
364 struct clk_si544_muldiv settings;
365 unsigned long center;
366 long max_delta;
367 long delta;
368 unsigned int old_oe_state;
369 int err;
370
371 if (!is_valid_frequency(data, rate))
372 return -EINVAL;
373
374 /* Try using the frequency adjustment feature for a <= 950ppm change */
375 err = si544_get_muldiv(data, &settings);
376 if (err)
377 return err;
378
379 center = si544_calc_center_rate(&settings);
380 max_delta = si544_max_delta(center);
381 delta = rate - center;
382
383 if (abs(delta) <= max_delta)
384 return si544_set_delta_m(data,
385 si544_calc_delta(delta, max_delta));
386
387 /* Too big for the delta adjustment, need to reprogram */
388 err = si544_calc_muldiv(&settings, rate);
389 if (err)
390 return err;
391
392 err = regmap_read(data->regmap, SI544_REG_OE_STATE, &old_oe_state);
393 if (err)
394 return err;
395
396 si544_enable_output(data, false);
397
398 /* Allow FCAL for this frequency update */
399 err = regmap_write(data->regmap, SI544_REG_FCAL_OVR, 0);
400 if (err < 0)
401 return err;
402
403 err = si544_set_delta_m(data, settings.delta_m);
404 if (err < 0)
405 return err;
406
407 err = si544_set_muldiv(data, &settings);
408 if (err < 0)
409 return err; /* Undefined state now, best to leave disabled */
410
411 /* Trigger calibration */
412 err = regmap_write(data->regmap, SI544_REG_CONTROL,
413 SI544_CONTROL_MS_ICAL2);
414 if (err < 0)
415 return err;
416
417 /* Applying a new frequency can take up to 10ms */
418 usleep_range(10000, 12000);
419
420 if (old_oe_state & SI544_OE_STATE_ODC_OE)
421 si544_enable_output(data, true);
422
423 return err;
424 }
425
426 static const struct clk_ops si544_clk_ops = {
427 .prepare = si544_prepare,
428 .unprepare = si544_unprepare,
429 .is_prepared = si544_is_prepared,
430 .recalc_rate = si544_recalc_rate,
431 .round_rate = si544_round_rate,
432 .set_rate = si544_set_rate,
433 };
434
si544_regmap_is_volatile(struct device * dev,unsigned int reg)435 static bool si544_regmap_is_volatile(struct device *dev, unsigned int reg)
436 {
437 switch (reg) {
438 case SI544_REG_CONTROL:
439 case SI544_REG_FCAL_OVR:
440 return true;
441 default:
442 return false;
443 }
444 }
445
446 static const struct regmap_config si544_regmap_config = {
447 .reg_bits = 8,
448 .val_bits = 8,
449 .cache_type = REGCACHE_RBTREE,
450 .max_register = SI544_REG_PAGE_SELECT,
451 .volatile_reg = si544_regmap_is_volatile,
452 };
453
454 static const struct i2c_device_id si544_id[] = {
455 { "si544a", si544a },
456 { "si544b", si544b },
457 { "si544c", si544c },
458 { }
459 };
460 MODULE_DEVICE_TABLE(i2c, si544_id);
461
si544_probe(struct i2c_client * client)462 static int si544_probe(struct i2c_client *client)
463 {
464 struct clk_si544 *data;
465 struct clk_init_data init;
466 const struct i2c_device_id *id = i2c_match_id(si544_id, client);
467 int err;
468
469 data = devm_kzalloc(&client->dev, sizeof(*data), GFP_KERNEL);
470 if (!data)
471 return -ENOMEM;
472
473 init.ops = &si544_clk_ops;
474 init.flags = 0;
475 init.num_parents = 0;
476 data->hw.init = &init;
477 data->i2c_client = client;
478 data->speed_grade = id->driver_data;
479
480 if (of_property_read_string(client->dev.of_node, "clock-output-names",
481 &init.name))
482 init.name = client->dev.of_node->name;
483
484 data->regmap = devm_regmap_init_i2c(client, &si544_regmap_config);
485 if (IS_ERR(data->regmap))
486 return PTR_ERR(data->regmap);
487
488 i2c_set_clientdata(client, data);
489
490 /* Select page 0, just to be sure, there appear to be no more */
491 err = regmap_write(data->regmap, SI544_REG_PAGE_SELECT, 0);
492 if (err < 0)
493 return err;
494
495 err = devm_clk_hw_register(&client->dev, &data->hw);
496 if (err) {
497 dev_err(&client->dev, "clock registration failed\n");
498 return err;
499 }
500 err = devm_of_clk_add_hw_provider(&client->dev, of_clk_hw_simple_get,
501 &data->hw);
502 if (err) {
503 dev_err(&client->dev, "unable to add clk provider\n");
504 return err;
505 }
506
507 return 0;
508 }
509
510 static const struct of_device_id clk_si544_of_match[] = {
511 { .compatible = "silabs,si544a" },
512 { .compatible = "silabs,si544b" },
513 { .compatible = "silabs,si544c" },
514 { },
515 };
516 MODULE_DEVICE_TABLE(of, clk_si544_of_match);
517
518 static struct i2c_driver si544_driver = {
519 .driver = {
520 .name = "si544",
521 .of_match_table = clk_si544_of_match,
522 },
523 .probe = si544_probe,
524 .id_table = si544_id,
525 };
526 module_i2c_driver(si544_driver);
527
528 MODULE_AUTHOR("Mike Looijmans <mike.looijmans@topic.nl>");
529 MODULE_DESCRIPTION("Si544 driver");
530 MODULE_LICENSE("GPL");
531