1 // SPDX-License-Identifier: GPL-2.0-only 2 /* 3 * Intel IXP4xx Expansion Bus Controller 4 * Copyright (C) 2021 Linaro Ltd. 5 * 6 * Author: Linus Walleij <linus.walleij@linaro.org> 7 */ 8 9 #include <linux/bitfield.h> 10 #include <linux/bits.h> 11 #include <linux/err.h> 12 #include <linux/init.h> 13 #include <linux/log2.h> 14 #include <linux/mfd/syscon.h> 15 #include <linux/module.h> 16 #include <linux/of.h> 17 #include <linux/of_platform.h> 18 #include <linux/platform_device.h> 19 #include <linux/regmap.h> 20 21 #define IXP4XX_EXP_NUM_CS 8 22 23 #define IXP4XX_EXP_TIMING_CS0 0x00 24 #define IXP4XX_EXP_TIMING_CS1 0x04 25 #define IXP4XX_EXP_TIMING_CS2 0x08 26 #define IXP4XX_EXP_TIMING_CS3 0x0c 27 #define IXP4XX_EXP_TIMING_CS4 0x10 28 #define IXP4XX_EXP_TIMING_CS5 0x14 29 #define IXP4XX_EXP_TIMING_CS6 0x18 30 #define IXP4XX_EXP_TIMING_CS7 0x1c 31 32 /* Bits inside each CS timing register */ 33 #define IXP4XX_EXP_TIMING_STRIDE 0x04 34 #define IXP4XX_EXP_CS_EN BIT(31) 35 #define IXP456_EXP_PAR_EN BIT(30) /* Only on IXP45x and IXP46x */ 36 #define IXP4XX_EXP_T1_MASK GENMASK(28, 27) 37 #define IXP4XX_EXP_T1_SHIFT 28 38 #define IXP4XX_EXP_T2_MASK GENMASK(27, 26) 39 #define IXP4XX_EXP_T2_SHIFT 26 40 #define IXP4XX_EXP_T3_MASK GENMASK(25, 22) 41 #define IXP4XX_EXP_T3_SHIFT 22 42 #define IXP4XX_EXP_T4_MASK GENMASK(21, 20) 43 #define IXP4XX_EXP_T4_SHIFT 20 44 #define IXP4XX_EXP_T5_MASK GENMASK(19, 16) 45 #define IXP4XX_EXP_T5_SHIFT 16 46 #define IXP4XX_EXP_CYC_TYPE_MASK GENMASK(15, 14) 47 #define IXP4XX_EXP_CYC_TYPE_SHIFT 14 48 #define IXP4XX_EXP_SIZE_MASK GENMASK(13, 10) 49 #define IXP4XX_EXP_SIZE_SHIFT 10 50 #define IXP4XX_EXP_CNFG_0 BIT(9) /* Always zero */ 51 #define IXP43X_EXP_SYNC_INTEL BIT(8) /* Only on IXP43x */ 52 #define IXP43X_EXP_EXP_CHIP BIT(7) /* Only on IXP43x, dangerous to touch on IXP42x */ 53 #define IXP4XX_EXP_BYTE_RD16 BIT(6) 54 #define IXP4XX_EXP_HRDY_POL BIT(5) /* Only on IXP42x */ 55 #define IXP4XX_EXP_MUX_EN BIT(4) 56 #define IXP4XX_EXP_SPLT_EN BIT(3) 57 #define IXP4XX_EXP_WORD BIT(2) /* Always zero */ 58 #define IXP4XX_EXP_WR_EN BIT(1) 59 #define IXP4XX_EXP_BYTE_EN BIT(0) 60 61 #define IXP4XX_EXP_CNFG0 0x20 62 #define IXP4XX_EXP_CNFG0_MEM_MAP BIT(31) 63 #define IXP4XX_EXP_CNFG1 0x24 64 65 #define IXP4XX_EXP_BOOT_BASE 0x00000000 66 #define IXP4XX_EXP_NORMAL_BASE 0x50000000 67 #define IXP4XX_EXP_STRIDE 0x01000000 68 69 /* Fuses on the IXP43x */ 70 #define IXP43X_EXP_UNIT_FUSE_RESET 0x28 71 #define IXP43x_EXP_FUSE_SPEED_MASK GENMASK(23, 22) 72 73 /* Number of device tree values in "reg" */ 74 #define IXP4XX_OF_REG_SIZE 3 75 76 struct ixp4xx_eb { 77 struct device *dev; 78 struct regmap *rmap; 79 u32 bus_base; 80 bool is_42x; 81 bool is_43x; 82 }; 83 84 struct ixp4xx_exp_tim_prop { 85 const char *prop; 86 u32 max; 87 u32 mask; 88 u16 shift; 89 }; 90 91 static const struct ixp4xx_exp_tim_prop ixp4xx_exp_tim_props[] = { 92 { 93 .prop = "intel,ixp4xx-eb-t1", 94 .max = 3, 95 .mask = IXP4XX_EXP_T1_MASK, 96 .shift = IXP4XX_EXP_T1_SHIFT, 97 }, 98 { 99 .prop = "intel,ixp4xx-eb-t2", 100 .max = 3, 101 .mask = IXP4XX_EXP_T2_MASK, 102 .shift = IXP4XX_EXP_T2_SHIFT, 103 }, 104 { 105 .prop = "intel,ixp4xx-eb-t3", 106 .max = 15, 107 .mask = IXP4XX_EXP_T3_MASK, 108 .shift = IXP4XX_EXP_T3_SHIFT, 109 }, 110 { 111 .prop = "intel,ixp4xx-eb-t4", 112 .max = 3, 113 .mask = IXP4XX_EXP_T4_MASK, 114 .shift = IXP4XX_EXP_T4_SHIFT, 115 }, 116 { 117 .prop = "intel,ixp4xx-eb-t5", 118 .max = 15, 119 .mask = IXP4XX_EXP_T5_MASK, 120 .shift = IXP4XX_EXP_T5_SHIFT, 121 }, 122 { 123 .prop = "intel,ixp4xx-eb-byte-access-on-halfword", 124 .max = 1, 125 .mask = IXP4XX_EXP_BYTE_RD16, 126 }, 127 { 128 .prop = "intel,ixp4xx-eb-hpi-hrdy-pol-high", 129 .max = 1, 130 .mask = IXP4XX_EXP_HRDY_POL, 131 }, 132 { 133 .prop = "intel,ixp4xx-eb-mux-address-and-data", 134 .max = 1, 135 .mask = IXP4XX_EXP_MUX_EN, 136 }, 137 { 138 .prop = "intel,ixp4xx-eb-ahb-split-transfers", 139 .max = 1, 140 .mask = IXP4XX_EXP_SPLT_EN, 141 }, 142 { 143 .prop = "intel,ixp4xx-eb-write-enable", 144 .max = 1, 145 .mask = IXP4XX_EXP_WR_EN, 146 }, 147 { 148 .prop = "intel,ixp4xx-eb-byte-access", 149 .max = 1, 150 .mask = IXP4XX_EXP_BYTE_EN, 151 }, 152 }; 153 154 static void ixp4xx_exp_setup_chipselect(struct ixp4xx_eb *eb, 155 struct device_node *np, 156 u32 cs_index, 157 u32 cs_size) 158 { 159 u32 cs_cfg; 160 u32 val; 161 u32 cur_cssize; 162 u32 cs_order; 163 int ret; 164 int i; 165 166 if (eb->is_42x && (cs_index > 7)) { 167 dev_err(eb->dev, 168 "invalid chipselect %u, we only support 0-7\n", 169 cs_index); 170 return; 171 } 172 if (eb->is_43x && (cs_index > 3)) { 173 dev_err(eb->dev, 174 "invalid chipselect %u, we only support 0-3\n", 175 cs_index); 176 return; 177 } 178 179 /* Several chip selects can be joined into one device */ 180 if (cs_size > IXP4XX_EXP_STRIDE) 181 cur_cssize = IXP4XX_EXP_STRIDE; 182 else 183 cur_cssize = cs_size; 184 185 186 /* 187 * The following will read/modify/write the configuration for one 188 * chipselect, attempting to leave the boot defaults in place unless 189 * something is explicitly defined. 190 */ 191 regmap_read(eb->rmap, IXP4XX_EXP_TIMING_CS0 + 192 IXP4XX_EXP_TIMING_STRIDE * cs_index, &cs_cfg); 193 dev_info(eb->dev, "CS%d at %#08x, size %#08x, config before: %#08x\n", 194 cs_index, eb->bus_base + IXP4XX_EXP_STRIDE * cs_index, 195 cur_cssize, cs_cfg); 196 197 /* Size set-up first align to 2^9 .. 2^24 */ 198 cur_cssize = roundup_pow_of_two(cur_cssize); 199 if (cur_cssize < 512) 200 cur_cssize = 512; 201 cs_order = ilog2(cur_cssize); 202 if (cs_order < 9 || cs_order > 24) { 203 dev_err(eb->dev, "illegal size order %d\n", cs_order); 204 return; 205 } 206 dev_dbg(eb->dev, "CS%d size order: %d\n", cs_index, cs_order); 207 cs_cfg &= ~(IXP4XX_EXP_SIZE_MASK); 208 cs_cfg |= ((cs_order - 9) << IXP4XX_EXP_SIZE_SHIFT); 209 210 for (i = 0; i < ARRAY_SIZE(ixp4xx_exp_tim_props); i++) { 211 const struct ixp4xx_exp_tim_prop *ip = &ixp4xx_exp_tim_props[i]; 212 213 /* All are regular u32 values */ 214 ret = of_property_read_u32(np, ip->prop, &val); 215 if (ret) 216 continue; 217 218 /* Handle bools (single bits) first */ 219 if (ip->max == 1) { 220 if (val) 221 cs_cfg |= ip->mask; 222 else 223 cs_cfg &= ~ip->mask; 224 dev_info(eb->dev, "CS%d %s %s\n", cs_index, 225 val ? "enabled" : "disabled", 226 ip->prop); 227 continue; 228 } 229 230 if (val > ip->max) { 231 dev_err(eb->dev, 232 "CS%d too high value for %s: %u, capped at %u\n", 233 cs_index, ip->prop, val, ip->max); 234 val = ip->max; 235 } 236 /* This assumes max value fills all the assigned bits (and it does) */ 237 cs_cfg &= ~ip->mask; 238 cs_cfg |= (val << ip->shift); 239 dev_info(eb->dev, "CS%d set %s to %u\n", cs_index, ip->prop, val); 240 } 241 242 ret = of_property_read_u32(np, "intel,ixp4xx-eb-cycle-type", &val); 243 if (!ret) { 244 if (val > 3) { 245 dev_err(eb->dev, "illegal cycle type %d\n", val); 246 return; 247 } 248 dev_info(eb->dev, "CS%d set cycle type %d\n", cs_index, val); 249 cs_cfg &= ~IXP4XX_EXP_CYC_TYPE_MASK; 250 cs_cfg |= val << IXP4XX_EXP_CYC_TYPE_SHIFT; 251 } 252 253 if (eb->is_43x) { 254 /* Should always be zero */ 255 cs_cfg &= ~IXP4XX_EXP_WORD; 256 /* 257 * This bit for Intel strata flash is currently unused, but let's 258 * report it if we find one. 259 */ 260 if (cs_cfg & IXP43X_EXP_SYNC_INTEL) 261 dev_info(eb->dev, "claims to be Intel strata flash\n"); 262 } 263 cs_cfg |= IXP4XX_EXP_CS_EN; 264 265 regmap_write(eb->rmap, 266 IXP4XX_EXP_TIMING_CS0 + IXP4XX_EXP_TIMING_STRIDE * cs_index, 267 cs_cfg); 268 dev_info(eb->dev, "CS%d wrote %#08x into CS config\n", cs_index, cs_cfg); 269 270 /* 271 * If several chip selects are joined together into one big 272 * device area, we call ourselves recursively for each successive 273 * chip select. For a 32MB flash chip this results in two calls 274 * for example. 275 */ 276 if (cs_size > IXP4XX_EXP_STRIDE) 277 ixp4xx_exp_setup_chipselect(eb, np, 278 cs_index + 1, 279 cs_size - IXP4XX_EXP_STRIDE); 280 } 281 282 static void ixp4xx_exp_setup_child(struct ixp4xx_eb *eb, 283 struct device_node *np) 284 { 285 u32 cs_sizes[IXP4XX_EXP_NUM_CS]; 286 int num_regs; 287 u32 csindex; 288 u32 cssize; 289 int ret; 290 int i; 291 292 num_regs = of_property_count_elems_of_size(np, "reg", IXP4XX_OF_REG_SIZE); 293 if (num_regs <= 0) 294 return; 295 dev_dbg(eb->dev, "child %s has %d register sets\n", 296 of_node_full_name(np), num_regs); 297 298 for (csindex = 0; csindex < IXP4XX_EXP_NUM_CS; csindex++) 299 cs_sizes[csindex] = 0; 300 301 for (i = 0; i < num_regs; i++) { 302 u32 rbase, rsize; 303 304 ret = of_property_read_u32_index(np, "reg", 305 i * IXP4XX_OF_REG_SIZE, &csindex); 306 if (ret) 307 break; 308 ret = of_property_read_u32_index(np, "reg", 309 i * IXP4XX_OF_REG_SIZE + 1, &rbase); 310 if (ret) 311 break; 312 ret = of_property_read_u32_index(np, "reg", 313 i * IXP4XX_OF_REG_SIZE + 2, &rsize); 314 if (ret) 315 break; 316 317 if (csindex >= IXP4XX_EXP_NUM_CS) { 318 dev_err(eb->dev, "illegal CS %d\n", csindex); 319 continue; 320 } 321 /* 322 * The memory window always starts from CS base so we need to add 323 * the start and size to get to the size from the start of the CS 324 * base. For example if CS0 is at 0x50000000 and the reg is 325 * <0 0xe40000 0x40000> the size is e80000. 326 * 327 * Roof this if we have several regs setting the same CS. 328 */ 329 cssize = rbase + rsize; 330 dev_dbg(eb->dev, "CS%d size %#08x\n", csindex, cssize); 331 if (cs_sizes[csindex] < cssize) 332 cs_sizes[csindex] = cssize; 333 } 334 335 for (csindex = 0; csindex < IXP4XX_EXP_NUM_CS; csindex++) { 336 cssize = cs_sizes[csindex]; 337 if (!cssize) 338 continue; 339 /* Just this one, so set it up and return */ 340 ixp4xx_exp_setup_chipselect(eb, np, csindex, cssize); 341 } 342 } 343 344 static int ixp4xx_exp_probe(struct platform_device *pdev) 345 { 346 struct device *dev = &pdev->dev; 347 struct device_node *np = dev->of_node; 348 struct ixp4xx_eb *eb; 349 struct device_node *child; 350 bool have_children = false; 351 u32 val; 352 int ret; 353 354 eb = devm_kzalloc(dev, sizeof(*eb), GFP_KERNEL); 355 if (!eb) 356 return -ENOMEM; 357 358 eb->dev = dev; 359 eb->is_42x = of_device_is_compatible(np, "intel,ixp42x-expansion-bus-controller"); 360 eb->is_43x = of_device_is_compatible(np, "intel,ixp43x-expansion-bus-controller"); 361 362 eb->rmap = syscon_node_to_regmap(np); 363 if (IS_ERR(eb->rmap)) 364 return dev_err_probe(dev, PTR_ERR(eb->rmap), "no regmap\n"); 365 366 /* We check that the regmap work only on first read */ 367 ret = regmap_read(eb->rmap, IXP4XX_EXP_CNFG0, &val); 368 if (ret) 369 return dev_err_probe(dev, ret, "cannot read regmap\n"); 370 if (val & IXP4XX_EXP_CNFG0_MEM_MAP) 371 eb->bus_base = IXP4XX_EXP_BOOT_BASE; 372 else 373 eb->bus_base = IXP4XX_EXP_NORMAL_BASE; 374 dev_info(dev, "expansion bus at %08x\n", eb->bus_base); 375 376 if (eb->is_43x) { 377 /* Check some fuses */ 378 regmap_read(eb->rmap, IXP43X_EXP_UNIT_FUSE_RESET, &val); 379 switch (FIELD_GET(IXP43x_EXP_FUSE_SPEED_MASK, val)) { 380 case 0: 381 dev_info(dev, "IXP43x at 533 MHz\n"); 382 break; 383 case 1: 384 dev_info(dev, "IXP43x at 400 MHz\n"); 385 break; 386 case 2: 387 dev_info(dev, "IXP43x at 667 MHz\n"); 388 break; 389 default: 390 dev_info(dev, "IXP43x unknown speed\n"); 391 break; 392 } 393 } 394 395 /* Walk over the child nodes and see what chipselects we use */ 396 for_each_available_child_of_node(np, child) { 397 ixp4xx_exp_setup_child(eb, child); 398 /* We have at least one child */ 399 have_children = true; 400 } 401 402 if (have_children) 403 return of_platform_default_populate(np, NULL, dev); 404 405 return 0; 406 } 407 408 static const struct of_device_id ixp4xx_exp_of_match[] = { 409 { .compatible = "intel,ixp42x-expansion-bus-controller", }, 410 { .compatible = "intel,ixp43x-expansion-bus-controller", }, 411 { .compatible = "intel,ixp45x-expansion-bus-controller", }, 412 { .compatible = "intel,ixp46x-expansion-bus-controller", }, 413 { } 414 }; 415 416 static struct platform_driver ixp4xx_exp_driver = { 417 .probe = ixp4xx_exp_probe, 418 .driver = { 419 .name = "intel-extbus", 420 .of_match_table = ixp4xx_exp_of_match, 421 }, 422 }; 423 module_platform_driver(ixp4xx_exp_driver); 424 MODULE_AUTHOR("Linus Walleij <linus.walleij@linaro.org>"); 425 MODULE_DESCRIPTION("Intel IXP4xx external bus driver"); 426