1 /**
2  * Marvell BT-over-SDIO driver: SDIO interface related definitions
3  *
4  * Copyright (C) 2009, Marvell International Ltd.
5  *
6  * This software file (the "File") is distributed by Marvell International
7  * Ltd. under the terms of the GNU General Public License Version 2, June 1991
8  * (the "License").  You may use, redistribute and/or modify this File in
9  * accordance with the terms and conditions of the License, a copy of which
10  * is available by writing to the Free Software Foundation, Inc.,
11  * 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA or on the
12  * worldwide web at http://www.gnu.org/licenses/old-licenses/gpl-2.0.txt.
13  *
14  *
15  * THE FILE IS DISTRIBUTED AS-IS, WITHOUT WARRANTY OF ANY KIND, AND THE
16  * IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE
17  * ARE EXPRESSLY DISCLAIMED.  The License provides additional details about
18  * this warranty disclaimer.
19  *
20  **/
21 
22 #define SDIO_HEADER_LEN			4
23 
24 /* SD block size can not bigger than 64 due to buf size limit in firmware */
25 /* define SD block size for data Tx/Rx */
26 #define SDIO_BLOCK_SIZE			64
27 
28 /* Number of blocks for firmware transfer */
29 #define FIRMWARE_TRANSFER_NBLOCK	2
30 
31 /* This is for firmware specific length */
32 #define FW_EXTRA_LEN			36
33 
34 #define MRVDRV_SIZE_OF_CMD_BUFFER       (2 * 1024)
35 
36 #define MRVDRV_BT_RX_PACKET_BUFFER_SIZE \
37 	(HCI_MAX_FRAME_SIZE + FW_EXTRA_LEN)
38 
39 #define ALLOC_BUF_SIZE	(((max_t (int, MRVDRV_BT_RX_PACKET_BUFFER_SIZE, \
40 			MRVDRV_SIZE_OF_CMD_BUFFER) + SDIO_HEADER_LEN \
41 			+ SDIO_BLOCK_SIZE - 1) / SDIO_BLOCK_SIZE) \
42 			* SDIO_BLOCK_SIZE)
43 
44 /* The number of times to try when polling for status */
45 #define MAX_POLL_TRIES			100
46 
47 /* Max retry number of CMD53 write */
48 #define MAX_WRITE_IOMEM_RETRY		2
49 
50 /* register bitmasks */
51 #define HOST_POWER_UP				BIT(1)
52 #define HOST_CMD53_FIN				BIT(2)
53 
54 #define HIM_DISABLE				0xff
55 #define HIM_ENABLE				(BIT(0) | BIT(1))
56 
57 #define UP_LD_HOST_INT_STATUS			BIT(0)
58 #define DN_LD_HOST_INT_STATUS			BIT(1)
59 
60 #define DN_LD_CARD_RDY				BIT(0)
61 #define CARD_IO_READY				BIT(3)
62 
63 #define FIRMWARE_READY				0xfedc
64 
65 
66 struct btmrvl_sdio_card_reg {
67 	u8 cfg;
68 	u8 host_int_mask;
69 	u8 host_intstatus;
70 	u8 card_status;
71 	u8 sq_read_base_addr_a0;
72 	u8 sq_read_base_addr_a1;
73 	u8 card_revision;
74 	u8 card_fw_status0;
75 	u8 card_fw_status1;
76 	u8 card_rx_len;
77 	u8 card_rx_unit;
78 	u8 io_port_0;
79 	u8 io_port_1;
80 	u8 io_port_2;
81 	bool int_read_to_clear;
82 	u8 host_int_rsr;
83 	u8 card_misc_cfg;
84 	u8 fw_dump_ctrl;
85 	u8 fw_dump_start;
86 	u8 fw_dump_end;
87 };
88 
89 struct btmrvl_sdio_card {
90 	struct sdio_func *func;
91 	u32 ioport;
92 	const char *helper;
93 	const char *firmware;
94 	const struct btmrvl_sdio_card_reg *reg;
95 	bool support_pscan_win_report;
96 	bool supports_fw_dump;
97 	u16 sd_blksz_fw_dl;
98 	u8 rx_unit;
99 	struct btmrvl_private *priv;
100 };
101 
102 struct btmrvl_sdio_device {
103 	const char *helper;
104 	const char *firmware;
105 	const struct btmrvl_sdio_card_reg *reg;
106 	const bool support_pscan_win_report;
107 	u16 sd_blksz_fw_dl;
108 	bool supports_fw_dump;
109 };
110 
111 
112 /* Platform specific DMA alignment */
113 #define BTSDIO_DMA_ALIGN		8
114 
115 /* Macros for Data Alignment : size */
116 #define ALIGN_SZ(p, a)	\
117 	(((p) + ((a) - 1)) & ~((a) - 1))
118 
119 /* Macros for Data Alignment : address */
120 #define ALIGN_ADDR(p, a)	\
121 	((((unsigned long)(p)) + (((unsigned long)(a)) - 1)) & \
122 					~(((unsigned long)(a)) - 1))
123