1 // SPDX-License-Identifier: GPL-2.0-or-later 2 /* 3 * Driver for the Micron P320 SSD 4 * Copyright (C) 2011 Micron Technology, Inc. 5 * 6 * Portions of this code were derived from works subjected to the 7 * following copyright: 8 * Copyright (C) 2009 Integrated Device Technology, Inc. 9 */ 10 11 #include <linux/pci.h> 12 #include <linux/interrupt.h> 13 #include <linux/ata.h> 14 #include <linux/delay.h> 15 #include <linux/hdreg.h> 16 #include <linux/uaccess.h> 17 #include <linux/random.h> 18 #include <linux/smp.h> 19 #include <linux/compat.h> 20 #include <linux/fs.h> 21 #include <linux/module.h> 22 #include <linux/blkdev.h> 23 #include <linux/blk-mq.h> 24 #include <linux/bio.h> 25 #include <linux/dma-mapping.h> 26 #include <linux/idr.h> 27 #include <linux/kthread.h> 28 #include <../drivers/ata/ahci.h> 29 #include <linux/export.h> 30 #include <linux/debugfs.h> 31 #include <linux/prefetch.h> 32 #include <linux/numa.h> 33 #include "mtip32xx.h" 34 35 #define HW_CMD_SLOT_SZ (MTIP_MAX_COMMAND_SLOTS * 32) 36 37 /* DMA region containing RX Fis, Identify, RLE10, and SMART buffers */ 38 #define AHCI_RX_FIS_SZ 0x100 39 #define AHCI_RX_FIS_OFFSET 0x0 40 #define AHCI_IDFY_SZ ATA_SECT_SIZE 41 #define AHCI_IDFY_OFFSET 0x400 42 #define AHCI_SECTBUF_SZ ATA_SECT_SIZE 43 #define AHCI_SECTBUF_OFFSET 0x800 44 #define AHCI_SMARTBUF_SZ ATA_SECT_SIZE 45 #define AHCI_SMARTBUF_OFFSET 0xC00 46 /* 0x100 + 0x200 + 0x200 + 0x200 is smaller than 4k but we pad it out */ 47 #define BLOCK_DMA_ALLOC_SZ 4096 48 49 /* DMA region containing command table (should be 8192 bytes) */ 50 #define AHCI_CMD_SLOT_SZ sizeof(struct mtip_cmd_hdr) 51 #define AHCI_CMD_TBL_SZ (MTIP_MAX_COMMAND_SLOTS * AHCI_CMD_SLOT_SZ) 52 #define AHCI_CMD_TBL_OFFSET 0x0 53 54 /* DMA region per command (contains header and SGL) */ 55 #define AHCI_CMD_TBL_HDR_SZ 0x80 56 #define AHCI_CMD_TBL_HDR_OFFSET 0x0 57 #define AHCI_CMD_TBL_SGL_SZ (MTIP_MAX_SG * sizeof(struct mtip_cmd_sg)) 58 #define AHCI_CMD_TBL_SGL_OFFSET AHCI_CMD_TBL_HDR_SZ 59 #define CMD_DMA_ALLOC_SZ (AHCI_CMD_TBL_SGL_SZ + AHCI_CMD_TBL_HDR_SZ) 60 61 62 #define HOST_CAP_NZDMA (1 << 19) 63 #define HOST_HSORG 0xFC 64 #define HSORG_DISABLE_SLOTGRP_INTR (1<<24) 65 #define HSORG_DISABLE_SLOTGRP_PXIS (1<<16) 66 #define HSORG_HWREV 0xFF00 67 #define HSORG_STYLE 0x8 68 #define HSORG_SLOTGROUPS 0x7 69 70 #define PORT_COMMAND_ISSUE 0x38 71 #define PORT_SDBV 0x7C 72 73 #define PORT_OFFSET 0x100 74 #define PORT_MEM_SIZE 0x80 75 76 #define PORT_IRQ_ERR \ 77 (PORT_IRQ_HBUS_ERR | PORT_IRQ_IF_ERR | PORT_IRQ_CONNECT | \ 78 PORT_IRQ_PHYRDY | PORT_IRQ_UNK_FIS | PORT_IRQ_BAD_PMP | \ 79 PORT_IRQ_TF_ERR | PORT_IRQ_HBUS_DATA_ERR | PORT_IRQ_IF_NONFATAL | \ 80 PORT_IRQ_OVERFLOW) 81 #define PORT_IRQ_LEGACY \ 82 (PORT_IRQ_PIOS_FIS | PORT_IRQ_D2H_REG_FIS) 83 #define PORT_IRQ_HANDLED \ 84 (PORT_IRQ_SDB_FIS | PORT_IRQ_LEGACY | \ 85 PORT_IRQ_TF_ERR | PORT_IRQ_IF_ERR | \ 86 PORT_IRQ_CONNECT | PORT_IRQ_PHYRDY) 87 #define DEF_PORT_IRQ \ 88 (PORT_IRQ_ERR | PORT_IRQ_LEGACY | PORT_IRQ_SDB_FIS) 89 90 /* product numbers */ 91 #define MTIP_PRODUCT_UNKNOWN 0x00 92 #define MTIP_PRODUCT_ASICFPGA 0x11 93 94 /* Device instance number, incremented each time a device is probed. */ 95 static int instance; 96 97 /* 98 * Global variable used to hold the major block device number 99 * allocated in mtip_init(). 100 */ 101 static int mtip_major; 102 static struct dentry *dfs_parent; 103 104 static u32 cpu_use[NR_CPUS]; 105 106 static DEFINE_IDA(rssd_index_ida); 107 108 static int mtip_block_initialize(struct driver_data *dd); 109 110 #ifdef CONFIG_COMPAT 111 struct mtip_compat_ide_task_request_s { 112 __u8 io_ports[8]; 113 __u8 hob_ports[8]; 114 ide_reg_valid_t out_flags; 115 ide_reg_valid_t in_flags; 116 int data_phase; 117 int req_cmd; 118 compat_ulong_t out_size; 119 compat_ulong_t in_size; 120 }; 121 #endif 122 123 /* 124 * This function check_for_surprise_removal is called 125 * while card is removed from the system and it will 126 * read the vendor id from the configuration space 127 * 128 * @pdev Pointer to the pci_dev structure. 129 * 130 * return value 131 * true if device removed, else false 132 */ 133 static bool mtip_check_surprise_removal(struct driver_data *dd) 134 { 135 u16 vendor_id = 0; 136 137 if (dd->sr) 138 return true; 139 140 /* Read the vendorID from the configuration space */ 141 pci_read_config_word(dd->pdev, 0x00, &vendor_id); 142 if (vendor_id == 0xFFFF) { 143 dd->sr = true; 144 if (dd->disk) 145 blk_mark_disk_dead(dd->disk); 146 return true; /* device removed */ 147 } 148 149 return false; /* device present */ 150 } 151 152 static struct mtip_cmd *mtip_cmd_from_tag(struct driver_data *dd, 153 unsigned int tag) 154 { 155 return blk_mq_rq_to_pdu(blk_mq_tag_to_rq(dd->tags.tags[0], tag)); 156 } 157 158 /* 159 * Reset the HBA (without sleeping) 160 * 161 * @dd Pointer to the driver data structure. 162 * 163 * return value 164 * 0 The reset was successful. 165 * -1 The HBA Reset bit did not clear. 166 */ 167 static int mtip_hba_reset(struct driver_data *dd) 168 { 169 unsigned long timeout; 170 171 /* Set the reset bit */ 172 writel(HOST_RESET, dd->mmio + HOST_CTL); 173 174 /* Flush */ 175 readl(dd->mmio + HOST_CTL); 176 177 /* 178 * Spin for up to 10 seconds waiting for reset acknowledgement. Spec 179 * is 1 sec but in LUN failure conditions, up to 10 secs are required 180 */ 181 timeout = jiffies + msecs_to_jiffies(10000); 182 do { 183 mdelay(10); 184 if (test_bit(MTIP_DDF_REMOVE_PENDING_BIT, &dd->dd_flag)) 185 return -1; 186 187 } while ((readl(dd->mmio + HOST_CTL) & HOST_RESET) 188 && time_before(jiffies, timeout)); 189 190 if (readl(dd->mmio + HOST_CTL) & HOST_RESET) 191 return -1; 192 193 return 0; 194 } 195 196 /* 197 * Issue a command to the hardware. 198 * 199 * Set the appropriate bit in the s_active and Command Issue hardware 200 * registers, causing hardware command processing to begin. 201 * 202 * @port Pointer to the port structure. 203 * @tag The tag of the command to be issued. 204 * 205 * return value 206 * None 207 */ 208 static inline void mtip_issue_ncq_command(struct mtip_port *port, int tag) 209 { 210 int group = tag >> 5; 211 212 /* guard SACT and CI registers */ 213 spin_lock(&port->cmd_issue_lock[group]); 214 writel((1 << MTIP_TAG_BIT(tag)), 215 port->s_active[MTIP_TAG_INDEX(tag)]); 216 writel((1 << MTIP_TAG_BIT(tag)), 217 port->cmd_issue[MTIP_TAG_INDEX(tag)]); 218 spin_unlock(&port->cmd_issue_lock[group]); 219 } 220 221 /* 222 * Enable/disable the reception of FIS 223 * 224 * @port Pointer to the port data structure 225 * @enable 1 to enable, 0 to disable 226 * 227 * return value 228 * Previous state: 1 enabled, 0 disabled 229 */ 230 static int mtip_enable_fis(struct mtip_port *port, int enable) 231 { 232 u32 tmp; 233 234 /* enable FIS reception */ 235 tmp = readl(port->mmio + PORT_CMD); 236 if (enable) 237 writel(tmp | PORT_CMD_FIS_RX, port->mmio + PORT_CMD); 238 else 239 writel(tmp & ~PORT_CMD_FIS_RX, port->mmio + PORT_CMD); 240 241 /* Flush */ 242 readl(port->mmio + PORT_CMD); 243 244 return (((tmp & PORT_CMD_FIS_RX) == PORT_CMD_FIS_RX)); 245 } 246 247 /* 248 * Enable/disable the DMA engine 249 * 250 * @port Pointer to the port data structure 251 * @enable 1 to enable, 0 to disable 252 * 253 * return value 254 * Previous state: 1 enabled, 0 disabled. 255 */ 256 static int mtip_enable_engine(struct mtip_port *port, int enable) 257 { 258 u32 tmp; 259 260 /* enable FIS reception */ 261 tmp = readl(port->mmio + PORT_CMD); 262 if (enable) 263 writel(tmp | PORT_CMD_START, port->mmio + PORT_CMD); 264 else 265 writel(tmp & ~PORT_CMD_START, port->mmio + PORT_CMD); 266 267 readl(port->mmio + PORT_CMD); 268 return (((tmp & PORT_CMD_START) == PORT_CMD_START)); 269 } 270 271 /* 272 * Enables the port DMA engine and FIS reception. 273 * 274 * return value 275 * None 276 */ 277 static inline void mtip_start_port(struct mtip_port *port) 278 { 279 /* Enable FIS reception */ 280 mtip_enable_fis(port, 1); 281 282 /* Enable the DMA engine */ 283 mtip_enable_engine(port, 1); 284 } 285 286 /* 287 * Deinitialize a port by disabling port interrupts, the DMA engine, 288 * and FIS reception. 289 * 290 * @port Pointer to the port structure 291 * 292 * return value 293 * None 294 */ 295 static inline void mtip_deinit_port(struct mtip_port *port) 296 { 297 /* Disable interrupts on this port */ 298 writel(0, port->mmio + PORT_IRQ_MASK); 299 300 /* Disable the DMA engine */ 301 mtip_enable_engine(port, 0); 302 303 /* Disable FIS reception */ 304 mtip_enable_fis(port, 0); 305 } 306 307 /* 308 * Initialize a port. 309 * 310 * This function deinitializes the port by calling mtip_deinit_port() and 311 * then initializes it by setting the command header and RX FIS addresses, 312 * clearing the SError register and any pending port interrupts before 313 * re-enabling the default set of port interrupts. 314 * 315 * @port Pointer to the port structure. 316 * 317 * return value 318 * None 319 */ 320 static void mtip_init_port(struct mtip_port *port) 321 { 322 int i; 323 mtip_deinit_port(port); 324 325 /* Program the command list base and FIS base addresses */ 326 if (readl(port->dd->mmio + HOST_CAP) & HOST_CAP_64) { 327 writel((port->command_list_dma >> 16) >> 16, 328 port->mmio + PORT_LST_ADDR_HI); 329 writel((port->rxfis_dma >> 16) >> 16, 330 port->mmio + PORT_FIS_ADDR_HI); 331 set_bit(MTIP_PF_HOST_CAP_64, &port->flags); 332 } 333 334 writel(port->command_list_dma & 0xFFFFFFFF, 335 port->mmio + PORT_LST_ADDR); 336 writel(port->rxfis_dma & 0xFFFFFFFF, port->mmio + PORT_FIS_ADDR); 337 338 /* Clear SError */ 339 writel(readl(port->mmio + PORT_SCR_ERR), port->mmio + PORT_SCR_ERR); 340 341 /* reset the completed registers.*/ 342 for (i = 0; i < port->dd->slot_groups; i++) 343 writel(0xFFFFFFFF, port->completed[i]); 344 345 /* Clear any pending interrupts for this port */ 346 writel(readl(port->mmio + PORT_IRQ_STAT), port->mmio + PORT_IRQ_STAT); 347 348 /* Clear any pending interrupts on the HBA. */ 349 writel(readl(port->dd->mmio + HOST_IRQ_STAT), 350 port->dd->mmio + HOST_IRQ_STAT); 351 352 /* Enable port interrupts */ 353 writel(DEF_PORT_IRQ, port->mmio + PORT_IRQ_MASK); 354 } 355 356 /* 357 * Restart a port 358 * 359 * @port Pointer to the port data structure. 360 * 361 * return value 362 * None 363 */ 364 static void mtip_restart_port(struct mtip_port *port) 365 { 366 unsigned long timeout; 367 368 /* Disable the DMA engine */ 369 mtip_enable_engine(port, 0); 370 371 /* Chip quirk: wait up to 500ms for PxCMD.CR == 0 */ 372 timeout = jiffies + msecs_to_jiffies(500); 373 while ((readl(port->mmio + PORT_CMD) & PORT_CMD_LIST_ON) 374 && time_before(jiffies, timeout)) 375 ; 376 377 if (test_bit(MTIP_DDF_REMOVE_PENDING_BIT, &port->dd->dd_flag)) 378 return; 379 380 /* 381 * Chip quirk: escalate to hba reset if 382 * PxCMD.CR not clear after 500 ms 383 */ 384 if (readl(port->mmio + PORT_CMD) & PORT_CMD_LIST_ON) { 385 dev_warn(&port->dd->pdev->dev, 386 "PxCMD.CR not clear, escalating reset\n"); 387 388 if (mtip_hba_reset(port->dd)) 389 dev_err(&port->dd->pdev->dev, 390 "HBA reset escalation failed.\n"); 391 392 /* 30 ms delay before com reset to quiesce chip */ 393 mdelay(30); 394 } 395 396 dev_warn(&port->dd->pdev->dev, "Issuing COM reset\n"); 397 398 /* Set PxSCTL.DET */ 399 writel(readl(port->mmio + PORT_SCR_CTL) | 400 1, port->mmio + PORT_SCR_CTL); 401 readl(port->mmio + PORT_SCR_CTL); 402 403 /* Wait 1 ms to quiesce chip function */ 404 timeout = jiffies + msecs_to_jiffies(1); 405 while (time_before(jiffies, timeout)) 406 ; 407 408 if (test_bit(MTIP_DDF_REMOVE_PENDING_BIT, &port->dd->dd_flag)) 409 return; 410 411 /* Clear PxSCTL.DET */ 412 writel(readl(port->mmio + PORT_SCR_CTL) & ~1, 413 port->mmio + PORT_SCR_CTL); 414 readl(port->mmio + PORT_SCR_CTL); 415 416 /* Wait 500 ms for bit 0 of PORT_SCR_STS to be set */ 417 timeout = jiffies + msecs_to_jiffies(500); 418 while (((readl(port->mmio + PORT_SCR_STAT) & 0x01) == 0) 419 && time_before(jiffies, timeout)) 420 ; 421 422 if (test_bit(MTIP_DDF_REMOVE_PENDING_BIT, &port->dd->dd_flag)) 423 return; 424 425 if ((readl(port->mmio + PORT_SCR_STAT) & 0x01) == 0) 426 dev_warn(&port->dd->pdev->dev, 427 "COM reset failed\n"); 428 429 mtip_init_port(port); 430 mtip_start_port(port); 431 432 } 433 434 static int mtip_device_reset(struct driver_data *dd) 435 { 436 int rv = 0; 437 438 if (mtip_check_surprise_removal(dd)) 439 return 0; 440 441 if (mtip_hba_reset(dd) < 0) 442 rv = -EFAULT; 443 444 mdelay(1); 445 mtip_init_port(dd->port); 446 mtip_start_port(dd->port); 447 448 /* Enable interrupts on the HBA. */ 449 writel(readl(dd->mmio + HOST_CTL) | HOST_IRQ_EN, 450 dd->mmio + HOST_CTL); 451 return rv; 452 } 453 454 /* 455 * Helper function for tag logging 456 */ 457 static void print_tags(struct driver_data *dd, 458 char *msg, 459 unsigned long *tagbits, 460 int cnt) 461 { 462 unsigned char tagmap[128]; 463 int group, tagmap_len = 0; 464 465 memset(tagmap, 0, sizeof(tagmap)); 466 for (group = SLOTBITS_IN_LONGS; group > 0; group--) 467 tagmap_len += sprintf(tagmap + tagmap_len, "%016lX ", 468 tagbits[group-1]); 469 dev_warn(&dd->pdev->dev, 470 "%d command(s) %s: tagmap [%s]", cnt, msg, tagmap); 471 } 472 473 static int mtip_read_log_page(struct mtip_port *port, u8 page, u16 *buffer, 474 dma_addr_t buffer_dma, unsigned int sectors); 475 static int mtip_get_smart_attr(struct mtip_port *port, unsigned int id, 476 struct smart_attr *attrib); 477 478 static void mtip_complete_command(struct mtip_cmd *cmd, blk_status_t status) 479 { 480 struct request *req = blk_mq_rq_from_pdu(cmd); 481 482 cmd->status = status; 483 if (likely(!blk_should_fake_timeout(req->q))) 484 blk_mq_complete_request(req); 485 } 486 487 /* 488 * Handle an error. 489 * 490 * @dd Pointer to the DRIVER_DATA structure. 491 * 492 * return value 493 * None 494 */ 495 static void mtip_handle_tfe(struct driver_data *dd) 496 { 497 int group, tag, bit, reissue, rv; 498 struct mtip_port *port; 499 struct mtip_cmd *cmd; 500 u32 completed; 501 struct host_to_dev_fis *fis; 502 unsigned long tagaccum[SLOTBITS_IN_LONGS]; 503 unsigned int cmd_cnt = 0; 504 unsigned char *buf; 505 char *fail_reason = NULL; 506 int fail_all_ncq_write = 0, fail_all_ncq_cmds = 0; 507 508 dev_warn(&dd->pdev->dev, "Taskfile error\n"); 509 510 port = dd->port; 511 512 if (test_bit(MTIP_PF_IC_ACTIVE_BIT, &port->flags)) { 513 cmd = mtip_cmd_from_tag(dd, MTIP_TAG_INTERNAL); 514 dbg_printk(MTIP_DRV_NAME " TFE for the internal command\n"); 515 mtip_complete_command(cmd, BLK_STS_IOERR); 516 return; 517 } 518 519 /* clear the tag accumulator */ 520 memset(tagaccum, 0, SLOTBITS_IN_LONGS * sizeof(long)); 521 522 /* Loop through all the groups */ 523 for (group = 0; group < dd->slot_groups; group++) { 524 completed = readl(port->completed[group]); 525 526 dev_warn(&dd->pdev->dev, "g=%u, comp=%x\n", group, completed); 527 528 /* clear completed status register in the hardware.*/ 529 writel(completed, port->completed[group]); 530 531 /* Process successfully completed commands */ 532 for (bit = 0; bit < 32 && completed; bit++) { 533 if (!(completed & (1<<bit))) 534 continue; 535 tag = (group << 5) + bit; 536 537 /* Skip the internal command slot */ 538 if (tag == MTIP_TAG_INTERNAL) 539 continue; 540 541 cmd = mtip_cmd_from_tag(dd, tag); 542 mtip_complete_command(cmd, 0); 543 set_bit(tag, tagaccum); 544 cmd_cnt++; 545 } 546 } 547 548 print_tags(dd, "completed (TFE)", tagaccum, cmd_cnt); 549 550 /* Restart the port */ 551 mdelay(20); 552 mtip_restart_port(port); 553 554 /* Trying to determine the cause of the error */ 555 rv = mtip_read_log_page(dd->port, ATA_LOG_SATA_NCQ, 556 dd->port->log_buf, 557 dd->port->log_buf_dma, 1); 558 if (rv) { 559 dev_warn(&dd->pdev->dev, 560 "Error in READ LOG EXT (10h) command\n"); 561 /* non-critical error, don't fail the load */ 562 } else { 563 buf = (unsigned char *)dd->port->log_buf; 564 if (buf[259] & 0x1) { 565 dev_info(&dd->pdev->dev, 566 "Write protect bit is set.\n"); 567 set_bit(MTIP_DDF_WRITE_PROTECT_BIT, &dd->dd_flag); 568 fail_all_ncq_write = 1; 569 fail_reason = "write protect"; 570 } 571 if (buf[288] == 0xF7) { 572 dev_info(&dd->pdev->dev, 573 "Exceeded Tmax, drive in thermal shutdown.\n"); 574 set_bit(MTIP_DDF_OVER_TEMP_BIT, &dd->dd_flag); 575 fail_all_ncq_cmds = 1; 576 fail_reason = "thermal shutdown"; 577 } 578 if (buf[288] == 0xBF) { 579 set_bit(MTIP_DDF_REBUILD_FAILED_BIT, &dd->dd_flag); 580 dev_info(&dd->pdev->dev, 581 "Drive indicates rebuild has failed. Secure erase required.\n"); 582 fail_all_ncq_cmds = 1; 583 fail_reason = "rebuild failed"; 584 } 585 } 586 587 /* clear the tag accumulator */ 588 memset(tagaccum, 0, SLOTBITS_IN_LONGS * sizeof(long)); 589 590 /* Loop through all the groups */ 591 for (group = 0; group < dd->slot_groups; group++) { 592 for (bit = 0; bit < 32; bit++) { 593 reissue = 1; 594 tag = (group << 5) + bit; 595 cmd = mtip_cmd_from_tag(dd, tag); 596 597 fis = (struct host_to_dev_fis *)cmd->command; 598 599 /* Should re-issue? */ 600 if (tag == MTIP_TAG_INTERNAL || 601 fis->command == ATA_CMD_SET_FEATURES) 602 reissue = 0; 603 else { 604 if (fail_all_ncq_cmds || 605 (fail_all_ncq_write && 606 fis->command == ATA_CMD_FPDMA_WRITE)) { 607 dev_warn(&dd->pdev->dev, 608 " Fail: %s w/tag %d [%s].\n", 609 fis->command == ATA_CMD_FPDMA_WRITE ? 610 "write" : "read", 611 tag, 612 fail_reason != NULL ? 613 fail_reason : "unknown"); 614 mtip_complete_command(cmd, BLK_STS_MEDIUM); 615 continue; 616 } 617 } 618 619 /* 620 * First check if this command has 621 * exceeded its retries. 622 */ 623 if (reissue && (cmd->retries-- > 0)) { 624 625 set_bit(tag, tagaccum); 626 627 /* Re-issue the command. */ 628 mtip_issue_ncq_command(port, tag); 629 630 continue; 631 } 632 633 /* Retire a command that will not be reissued */ 634 dev_warn(&port->dd->pdev->dev, 635 "retiring tag %d\n", tag); 636 637 mtip_complete_command(cmd, BLK_STS_IOERR); 638 } 639 } 640 print_tags(dd, "reissued (TFE)", tagaccum, cmd_cnt); 641 } 642 643 /* 644 * Handle a set device bits interrupt 645 */ 646 static inline void mtip_workq_sdbfx(struct mtip_port *port, int group, 647 u32 completed) 648 { 649 struct driver_data *dd = port->dd; 650 int tag, bit; 651 struct mtip_cmd *command; 652 653 if (!completed) { 654 WARN_ON_ONCE(!completed); 655 return; 656 } 657 /* clear completed status register in the hardware.*/ 658 writel(completed, port->completed[group]); 659 660 /* Process completed commands. */ 661 for (bit = 0; (bit < 32) && completed; bit++) { 662 if (completed & 0x01) { 663 tag = (group << 5) | bit; 664 665 /* skip internal command slot. */ 666 if (unlikely(tag == MTIP_TAG_INTERNAL)) 667 continue; 668 669 command = mtip_cmd_from_tag(dd, tag); 670 mtip_complete_command(command, 0); 671 } 672 completed >>= 1; 673 } 674 675 /* If last, re-enable interrupts */ 676 if (atomic_dec_return(&dd->irq_workers_active) == 0) 677 writel(0xffffffff, dd->mmio + HOST_IRQ_STAT); 678 } 679 680 /* 681 * Process legacy pio and d2h interrupts 682 */ 683 static inline void mtip_process_legacy(struct driver_data *dd, u32 port_stat) 684 { 685 struct mtip_port *port = dd->port; 686 struct mtip_cmd *cmd = mtip_cmd_from_tag(dd, MTIP_TAG_INTERNAL); 687 688 if (test_bit(MTIP_PF_IC_ACTIVE_BIT, &port->flags) && cmd) { 689 int group = MTIP_TAG_INDEX(MTIP_TAG_INTERNAL); 690 int status = readl(port->cmd_issue[group]); 691 692 if (!(status & (1 << MTIP_TAG_BIT(MTIP_TAG_INTERNAL)))) 693 mtip_complete_command(cmd, 0); 694 } 695 } 696 697 /* 698 * Demux and handle errors 699 */ 700 static inline void mtip_process_errors(struct driver_data *dd, u32 port_stat) 701 { 702 if (unlikely(port_stat & PORT_IRQ_CONNECT)) { 703 dev_warn(&dd->pdev->dev, 704 "Clearing PxSERR.DIAG.x\n"); 705 writel((1 << 26), dd->port->mmio + PORT_SCR_ERR); 706 } 707 708 if (unlikely(port_stat & PORT_IRQ_PHYRDY)) { 709 dev_warn(&dd->pdev->dev, 710 "Clearing PxSERR.DIAG.n\n"); 711 writel((1 << 16), dd->port->mmio + PORT_SCR_ERR); 712 } 713 714 if (unlikely(port_stat & ~PORT_IRQ_HANDLED)) { 715 dev_warn(&dd->pdev->dev, 716 "Port stat errors %x unhandled\n", 717 (port_stat & ~PORT_IRQ_HANDLED)); 718 if (mtip_check_surprise_removal(dd)) 719 return; 720 } 721 if (likely(port_stat & (PORT_IRQ_TF_ERR | PORT_IRQ_IF_ERR))) { 722 set_bit(MTIP_PF_EH_ACTIVE_BIT, &dd->port->flags); 723 wake_up_interruptible(&dd->port->svc_wait); 724 } 725 } 726 727 static inline irqreturn_t mtip_handle_irq(struct driver_data *data) 728 { 729 struct driver_data *dd = (struct driver_data *) data; 730 struct mtip_port *port = dd->port; 731 u32 hba_stat, port_stat; 732 int rv = IRQ_NONE; 733 int do_irq_enable = 1, i, workers; 734 struct mtip_work *twork; 735 736 hba_stat = readl(dd->mmio + HOST_IRQ_STAT); 737 if (hba_stat) { 738 rv = IRQ_HANDLED; 739 740 /* Acknowledge the interrupt status on the port.*/ 741 port_stat = readl(port->mmio + PORT_IRQ_STAT); 742 if (unlikely(port_stat == 0xFFFFFFFF)) { 743 mtip_check_surprise_removal(dd); 744 return IRQ_HANDLED; 745 } 746 writel(port_stat, port->mmio + PORT_IRQ_STAT); 747 748 /* Demux port status */ 749 if (likely(port_stat & PORT_IRQ_SDB_FIS)) { 750 do_irq_enable = 0; 751 WARN_ON_ONCE(atomic_read(&dd->irq_workers_active) != 0); 752 753 /* Start at 1: group zero is always local? */ 754 for (i = 0, workers = 0; i < MTIP_MAX_SLOT_GROUPS; 755 i++) { 756 twork = &dd->work[i]; 757 twork->completed = readl(port->completed[i]); 758 if (twork->completed) 759 workers++; 760 } 761 762 atomic_set(&dd->irq_workers_active, workers); 763 if (workers) { 764 for (i = 1; i < MTIP_MAX_SLOT_GROUPS; i++) { 765 twork = &dd->work[i]; 766 if (twork->completed) 767 queue_work_on( 768 twork->cpu_binding, 769 dd->isr_workq, 770 &twork->work); 771 } 772 773 if (likely(dd->work[0].completed)) 774 mtip_workq_sdbfx(port, 0, 775 dd->work[0].completed); 776 777 } else { 778 /* 779 * Chip quirk: SDB interrupt but nothing 780 * to complete 781 */ 782 do_irq_enable = 1; 783 } 784 } 785 786 if (unlikely(port_stat & PORT_IRQ_ERR)) { 787 if (unlikely(mtip_check_surprise_removal(dd))) { 788 /* don't proceed further */ 789 return IRQ_HANDLED; 790 } 791 if (test_bit(MTIP_DDF_REMOVE_PENDING_BIT, 792 &dd->dd_flag)) 793 return rv; 794 795 mtip_process_errors(dd, port_stat & PORT_IRQ_ERR); 796 } 797 798 if (unlikely(port_stat & PORT_IRQ_LEGACY)) 799 mtip_process_legacy(dd, port_stat & PORT_IRQ_LEGACY); 800 } 801 802 /* acknowledge interrupt */ 803 if (unlikely(do_irq_enable)) 804 writel(hba_stat, dd->mmio + HOST_IRQ_STAT); 805 806 return rv; 807 } 808 809 /* 810 * HBA interrupt subroutine. 811 * 812 * @irq IRQ number. 813 * @instance Pointer to the driver data structure. 814 * 815 * return value 816 * IRQ_HANDLED A HBA interrupt was pending and handled. 817 * IRQ_NONE This interrupt was not for the HBA. 818 */ 819 static irqreturn_t mtip_irq_handler(int irq, void *instance) 820 { 821 struct driver_data *dd = instance; 822 823 return mtip_handle_irq(dd); 824 } 825 826 static void mtip_issue_non_ncq_command(struct mtip_port *port, int tag) 827 { 828 writel(1 << MTIP_TAG_BIT(tag), port->cmd_issue[MTIP_TAG_INDEX(tag)]); 829 } 830 831 static bool mtip_pause_ncq(struct mtip_port *port, 832 struct host_to_dev_fis *fis) 833 { 834 unsigned long task_file_data; 835 836 task_file_data = readl(port->mmio+PORT_TFDATA); 837 if ((task_file_data & 1)) 838 return false; 839 840 if (fis->command == ATA_CMD_SEC_ERASE_PREP) { 841 port->ic_pause_timer = jiffies; 842 return true; 843 } else if ((fis->command == ATA_CMD_DOWNLOAD_MICRO) && 844 (fis->features == 0x03)) { 845 set_bit(MTIP_PF_DM_ACTIVE_BIT, &port->flags); 846 port->ic_pause_timer = jiffies; 847 return true; 848 } else if ((fis->command == ATA_CMD_SEC_ERASE_UNIT) || 849 ((fis->command == 0xFC) && 850 (fis->features == 0x27 || fis->features == 0x72 || 851 fis->features == 0x62 || fis->features == 0x26))) { 852 clear_bit(MTIP_DDF_SEC_LOCK_BIT, &port->dd->dd_flag); 853 clear_bit(MTIP_DDF_REBUILD_FAILED_BIT, &port->dd->dd_flag); 854 /* Com reset after secure erase or lowlevel format */ 855 mtip_restart_port(port); 856 clear_bit(MTIP_PF_SE_ACTIVE_BIT, &port->flags); 857 return false; 858 } 859 860 return false; 861 } 862 863 static bool mtip_commands_active(struct mtip_port *port) 864 { 865 unsigned int active; 866 unsigned int n; 867 868 /* 869 * Ignore s_active bit 0 of array element 0. 870 * This bit will always be set 871 */ 872 active = readl(port->s_active[0]) & 0xFFFFFFFE; 873 for (n = 1; n < port->dd->slot_groups; n++) 874 active |= readl(port->s_active[n]); 875 876 return active != 0; 877 } 878 879 /* 880 * Wait for port to quiesce 881 * 882 * @port Pointer to port data structure 883 * @timeout Max duration to wait (ms) 884 * 885 * return value 886 * 0 Success 887 * -EBUSY Commands still active 888 */ 889 static int mtip_quiesce_io(struct mtip_port *port, unsigned long timeout) 890 { 891 unsigned long to; 892 bool active = true; 893 894 blk_mq_quiesce_queue(port->dd->queue); 895 896 to = jiffies + msecs_to_jiffies(timeout); 897 do { 898 if (test_bit(MTIP_PF_SVC_THD_ACTIVE_BIT, &port->flags) && 899 test_bit(MTIP_PF_ISSUE_CMDS_BIT, &port->flags)) { 900 msleep(20); 901 continue; /* svc thd is actively issuing commands */ 902 } 903 904 msleep(100); 905 906 if (mtip_check_surprise_removal(port->dd)) 907 goto err_fault; 908 909 active = mtip_commands_active(port); 910 if (!active) 911 break; 912 } while (time_before(jiffies, to)); 913 914 blk_mq_unquiesce_queue(port->dd->queue); 915 return active ? -EBUSY : 0; 916 err_fault: 917 blk_mq_unquiesce_queue(port->dd->queue); 918 return -EFAULT; 919 } 920 921 struct mtip_int_cmd { 922 int fis_len; 923 dma_addr_t buffer; 924 int buf_len; 925 u32 opts; 926 }; 927 928 /* 929 * Execute an internal command and wait for the completion. 930 * 931 * @port Pointer to the port data structure. 932 * @fis Pointer to the FIS that describes the command. 933 * @fis_len Length in WORDS of the FIS. 934 * @buffer DMA accessible for command data. 935 * @buf_len Length, in bytes, of the data buffer. 936 * @opts Command header options, excluding the FIS length 937 * and the number of PRD entries. 938 * @timeout Time in ms to wait for the command to complete. 939 * 940 * return value 941 * 0 Command completed successfully. 942 * -EFAULT The buffer address is not correctly aligned. 943 * -EBUSY Internal command or other IO in progress. 944 * -EAGAIN Time out waiting for command to complete. 945 */ 946 static int mtip_exec_internal_command(struct mtip_port *port, 947 struct host_to_dev_fis *fis, 948 int fis_len, 949 dma_addr_t buffer, 950 int buf_len, 951 u32 opts, 952 unsigned long timeout) 953 { 954 struct mtip_cmd *int_cmd; 955 struct driver_data *dd = port->dd; 956 struct request *rq; 957 struct mtip_int_cmd icmd = { 958 .fis_len = fis_len, 959 .buffer = buffer, 960 .buf_len = buf_len, 961 .opts = opts 962 }; 963 int rv = 0; 964 965 /* Make sure the buffer is 8 byte aligned. This is asic specific. */ 966 if (buffer & 0x00000007) { 967 dev_err(&dd->pdev->dev, "SG buffer is not 8 byte aligned\n"); 968 return -EFAULT; 969 } 970 971 if (mtip_check_surprise_removal(dd)) 972 return -EFAULT; 973 974 rq = blk_mq_alloc_request(dd->queue, REQ_OP_DRV_IN, BLK_MQ_REQ_RESERVED); 975 if (IS_ERR(rq)) { 976 dbg_printk(MTIP_DRV_NAME "Unable to allocate tag for PIO cmd\n"); 977 return -EFAULT; 978 } 979 980 set_bit(MTIP_PF_IC_ACTIVE_BIT, &port->flags); 981 982 if (fis->command == ATA_CMD_SEC_ERASE_PREP) 983 set_bit(MTIP_PF_SE_ACTIVE_BIT, &port->flags); 984 985 clear_bit(MTIP_PF_DM_ACTIVE_BIT, &port->flags); 986 987 if (fis->command != ATA_CMD_STANDBYNOW1) { 988 /* wait for io to complete if non atomic */ 989 if (mtip_quiesce_io(port, MTIP_QUIESCE_IO_TIMEOUT_MS) < 0) { 990 dev_warn(&dd->pdev->dev, "Failed to quiesce IO\n"); 991 blk_mq_free_request(rq); 992 clear_bit(MTIP_PF_IC_ACTIVE_BIT, &port->flags); 993 wake_up_interruptible(&port->svc_wait); 994 return -EBUSY; 995 } 996 } 997 998 /* Copy the command to the command table */ 999 int_cmd = blk_mq_rq_to_pdu(rq); 1000 int_cmd->icmd = &icmd; 1001 memcpy(int_cmd->command, fis, fis_len*4); 1002 1003 rq->timeout = timeout; 1004 1005 /* insert request and run queue */ 1006 blk_execute_rq(rq, true); 1007 1008 if (int_cmd->status) { 1009 dev_err(&dd->pdev->dev, "Internal command [%02X] failed %d\n", 1010 fis->command, int_cmd->status); 1011 rv = -EIO; 1012 1013 if (mtip_check_surprise_removal(dd) || 1014 test_bit(MTIP_DDF_REMOVE_PENDING_BIT, 1015 &dd->dd_flag)) { 1016 dev_err(&dd->pdev->dev, 1017 "Internal command [%02X] wait returned due to SR\n", 1018 fis->command); 1019 rv = -ENXIO; 1020 goto exec_ic_exit; 1021 } 1022 mtip_device_reset(dd); /* recover from timeout issue */ 1023 rv = -EAGAIN; 1024 goto exec_ic_exit; 1025 } 1026 1027 if (readl(port->cmd_issue[MTIP_TAG_INDEX(MTIP_TAG_INTERNAL)]) 1028 & (1 << MTIP_TAG_BIT(MTIP_TAG_INTERNAL))) { 1029 rv = -ENXIO; 1030 if (!test_bit(MTIP_DDF_REMOVE_PENDING_BIT, &dd->dd_flag)) { 1031 mtip_device_reset(dd); 1032 rv = -EAGAIN; 1033 } 1034 } 1035 exec_ic_exit: 1036 /* Clear the allocated and active bits for the internal command. */ 1037 blk_mq_free_request(rq); 1038 clear_bit(MTIP_PF_IC_ACTIVE_BIT, &port->flags); 1039 if (rv >= 0 && mtip_pause_ncq(port, fis)) { 1040 /* NCQ paused */ 1041 return rv; 1042 } 1043 wake_up_interruptible(&port->svc_wait); 1044 1045 return rv; 1046 } 1047 1048 /* 1049 * Byte-swap ATA ID strings. 1050 * 1051 * ATA identify data contains strings in byte-swapped 16-bit words. 1052 * They must be swapped (on all architectures) to be usable as C strings. 1053 * This function swaps bytes in-place. 1054 * 1055 * @buf The buffer location of the string 1056 * @len The number of bytes to swap 1057 * 1058 * return value 1059 * None 1060 */ 1061 static inline void ata_swap_string(u16 *buf, unsigned int len) 1062 { 1063 int i; 1064 for (i = 0; i < (len/2); i++) 1065 be16_to_cpus(&buf[i]); 1066 } 1067 1068 static void mtip_set_timeout(struct driver_data *dd, 1069 struct host_to_dev_fis *fis, 1070 unsigned int *timeout, u8 erasemode) 1071 { 1072 switch (fis->command) { 1073 case ATA_CMD_DOWNLOAD_MICRO: 1074 *timeout = 120000; /* 2 minutes */ 1075 break; 1076 case ATA_CMD_SEC_ERASE_UNIT: 1077 case 0xFC: 1078 if (erasemode) 1079 *timeout = ((*(dd->port->identify + 90) * 2) * 60000); 1080 else 1081 *timeout = ((*(dd->port->identify + 89) * 2) * 60000); 1082 break; 1083 case ATA_CMD_STANDBYNOW1: 1084 *timeout = 120000; /* 2 minutes */ 1085 break; 1086 case 0xF7: 1087 case 0xFA: 1088 *timeout = 60000; /* 60 seconds */ 1089 break; 1090 case ATA_CMD_SMART: 1091 *timeout = 15000; /* 15 seconds */ 1092 break; 1093 default: 1094 *timeout = MTIP_IOCTL_CMD_TIMEOUT_MS; 1095 break; 1096 } 1097 } 1098 1099 /* 1100 * Request the device identity information. 1101 * 1102 * If a user space buffer is not specified, i.e. is NULL, the 1103 * identify information is still read from the drive and placed 1104 * into the identify data buffer (@e port->identify) in the 1105 * port data structure. 1106 * When the identify buffer contains valid identify information @e 1107 * port->identify_valid is non-zero. 1108 * 1109 * @port Pointer to the port structure. 1110 * @user_buffer A user space buffer where the identify data should be 1111 * copied. 1112 * 1113 * return value 1114 * 0 Command completed successfully. 1115 * -EFAULT An error occurred while coping data to the user buffer. 1116 * -1 Command failed. 1117 */ 1118 static int mtip_get_identify(struct mtip_port *port, void __user *user_buffer) 1119 { 1120 int rv = 0; 1121 struct host_to_dev_fis fis; 1122 1123 if (test_bit(MTIP_DDF_REMOVE_PENDING_BIT, &port->dd->dd_flag)) 1124 return -EFAULT; 1125 1126 /* Build the FIS. */ 1127 memset(&fis, 0, sizeof(struct host_to_dev_fis)); 1128 fis.type = 0x27; 1129 fis.opts = 1 << 7; 1130 fis.command = ATA_CMD_ID_ATA; 1131 1132 /* Set the identify information as invalid. */ 1133 port->identify_valid = 0; 1134 1135 /* Clear the identify information. */ 1136 memset(port->identify, 0, sizeof(u16) * ATA_ID_WORDS); 1137 1138 /* Execute the command. */ 1139 if (mtip_exec_internal_command(port, 1140 &fis, 1141 5, 1142 port->identify_dma, 1143 sizeof(u16) * ATA_ID_WORDS, 1144 0, 1145 MTIP_INT_CMD_TIMEOUT_MS) 1146 < 0) { 1147 rv = -1; 1148 goto out; 1149 } 1150 1151 /* 1152 * Perform any necessary byte-swapping. Yes, the kernel does in fact 1153 * perform field-sensitive swapping on the string fields. 1154 * See the kernel use of ata_id_string() for proof of this. 1155 */ 1156 #ifdef __LITTLE_ENDIAN 1157 ata_swap_string(port->identify + 27, 40); /* model string*/ 1158 ata_swap_string(port->identify + 23, 8); /* firmware string*/ 1159 ata_swap_string(port->identify + 10, 20); /* serial# string*/ 1160 #else 1161 { 1162 int i; 1163 for (i = 0; i < ATA_ID_WORDS; i++) 1164 port->identify[i] = le16_to_cpu(port->identify[i]); 1165 } 1166 #endif 1167 1168 /* Check security locked state */ 1169 if (port->identify[128] & 0x4) 1170 set_bit(MTIP_DDF_SEC_LOCK_BIT, &port->dd->dd_flag); 1171 else 1172 clear_bit(MTIP_DDF_SEC_LOCK_BIT, &port->dd->dd_flag); 1173 1174 /* Set the identify buffer as valid. */ 1175 port->identify_valid = 1; 1176 1177 if (user_buffer) { 1178 if (copy_to_user( 1179 user_buffer, 1180 port->identify, 1181 ATA_ID_WORDS * sizeof(u16))) { 1182 rv = -EFAULT; 1183 goto out; 1184 } 1185 } 1186 1187 out: 1188 return rv; 1189 } 1190 1191 /* 1192 * Issue a standby immediate command to the device. 1193 * 1194 * @port Pointer to the port structure. 1195 * 1196 * return value 1197 * 0 Command was executed successfully. 1198 * -1 An error occurred while executing the command. 1199 */ 1200 static int mtip_standby_immediate(struct mtip_port *port) 1201 { 1202 int rv; 1203 struct host_to_dev_fis fis; 1204 unsigned long __maybe_unused start; 1205 unsigned int timeout; 1206 1207 /* Build the FIS. */ 1208 memset(&fis, 0, sizeof(struct host_to_dev_fis)); 1209 fis.type = 0x27; 1210 fis.opts = 1 << 7; 1211 fis.command = ATA_CMD_STANDBYNOW1; 1212 1213 mtip_set_timeout(port->dd, &fis, &timeout, 0); 1214 1215 start = jiffies; 1216 rv = mtip_exec_internal_command(port, 1217 &fis, 1218 5, 1219 0, 1220 0, 1221 0, 1222 timeout); 1223 dbg_printk(MTIP_DRV_NAME "Time taken to complete standby cmd: %d ms\n", 1224 jiffies_to_msecs(jiffies - start)); 1225 if (rv) 1226 dev_warn(&port->dd->pdev->dev, 1227 "STANDBY IMMEDIATE command failed.\n"); 1228 1229 return rv; 1230 } 1231 1232 /* 1233 * Issue a READ LOG EXT command to the device. 1234 * 1235 * @port pointer to the port structure. 1236 * @page page number to fetch 1237 * @buffer pointer to buffer 1238 * @buffer_dma dma address corresponding to @buffer 1239 * @sectors page length to fetch, in sectors 1240 * 1241 * return value 1242 * @rv return value from mtip_exec_internal_command() 1243 */ 1244 static int mtip_read_log_page(struct mtip_port *port, u8 page, u16 *buffer, 1245 dma_addr_t buffer_dma, unsigned int sectors) 1246 { 1247 struct host_to_dev_fis fis; 1248 1249 memset(&fis, 0, sizeof(struct host_to_dev_fis)); 1250 fis.type = 0x27; 1251 fis.opts = 1 << 7; 1252 fis.command = ATA_CMD_READ_LOG_EXT; 1253 fis.sect_count = sectors & 0xFF; 1254 fis.sect_cnt_ex = (sectors >> 8) & 0xFF; 1255 fis.lba_low = page; 1256 fis.lba_mid = 0; 1257 fis.device = ATA_DEVICE_OBS; 1258 1259 memset(buffer, 0, sectors * ATA_SECT_SIZE); 1260 1261 return mtip_exec_internal_command(port, 1262 &fis, 1263 5, 1264 buffer_dma, 1265 sectors * ATA_SECT_SIZE, 1266 0, 1267 MTIP_INT_CMD_TIMEOUT_MS); 1268 } 1269 1270 /* 1271 * Issue a SMART READ DATA command to the device. 1272 * 1273 * @port pointer to the port structure. 1274 * @buffer pointer to buffer 1275 * @buffer_dma dma address corresponding to @buffer 1276 * 1277 * return value 1278 * @rv return value from mtip_exec_internal_command() 1279 */ 1280 static int mtip_get_smart_data(struct mtip_port *port, u8 *buffer, 1281 dma_addr_t buffer_dma) 1282 { 1283 struct host_to_dev_fis fis; 1284 1285 memset(&fis, 0, sizeof(struct host_to_dev_fis)); 1286 fis.type = 0x27; 1287 fis.opts = 1 << 7; 1288 fis.command = ATA_CMD_SMART; 1289 fis.features = 0xD0; 1290 fis.sect_count = 1; 1291 fis.lba_mid = 0x4F; 1292 fis.lba_hi = 0xC2; 1293 fis.device = ATA_DEVICE_OBS; 1294 1295 return mtip_exec_internal_command(port, 1296 &fis, 1297 5, 1298 buffer_dma, 1299 ATA_SECT_SIZE, 1300 0, 1301 15000); 1302 } 1303 1304 /* 1305 * Get the value of a smart attribute 1306 * 1307 * @port pointer to the port structure 1308 * @id attribute number 1309 * @attrib pointer to return attrib information corresponding to @id 1310 * 1311 * return value 1312 * -EINVAL NULL buffer passed or unsupported attribute @id. 1313 * -EPERM Identify data not valid, SMART not supported or not enabled 1314 */ 1315 static int mtip_get_smart_attr(struct mtip_port *port, unsigned int id, 1316 struct smart_attr *attrib) 1317 { 1318 int rv, i; 1319 struct smart_attr *pattr; 1320 1321 if (!attrib) 1322 return -EINVAL; 1323 1324 if (!port->identify_valid) { 1325 dev_warn(&port->dd->pdev->dev, "IDENTIFY DATA not valid\n"); 1326 return -EPERM; 1327 } 1328 if (!(port->identify[82] & 0x1)) { 1329 dev_warn(&port->dd->pdev->dev, "SMART not supported\n"); 1330 return -EPERM; 1331 } 1332 if (!(port->identify[85] & 0x1)) { 1333 dev_warn(&port->dd->pdev->dev, "SMART not enabled\n"); 1334 return -EPERM; 1335 } 1336 1337 memset(port->smart_buf, 0, ATA_SECT_SIZE); 1338 rv = mtip_get_smart_data(port, port->smart_buf, port->smart_buf_dma); 1339 if (rv) { 1340 dev_warn(&port->dd->pdev->dev, "Failed to ge SMART data\n"); 1341 return rv; 1342 } 1343 1344 pattr = (struct smart_attr *)(port->smart_buf + 2); 1345 for (i = 0; i < 29; i++, pattr++) 1346 if (pattr->attr_id == id) { 1347 memcpy(attrib, pattr, sizeof(struct smart_attr)); 1348 break; 1349 } 1350 1351 if (i == 29) { 1352 dev_warn(&port->dd->pdev->dev, 1353 "Query for invalid SMART attribute ID\n"); 1354 rv = -EINVAL; 1355 } 1356 1357 return rv; 1358 } 1359 1360 /* 1361 * Get the drive capacity. 1362 * 1363 * @dd Pointer to the device data structure. 1364 * @sectors Pointer to the variable that will receive the sector count. 1365 * 1366 * return value 1367 * 1 Capacity was returned successfully. 1368 * 0 The identify information is invalid. 1369 */ 1370 static bool mtip_hw_get_capacity(struct driver_data *dd, sector_t *sectors) 1371 { 1372 struct mtip_port *port = dd->port; 1373 u64 total, raw0, raw1, raw2, raw3; 1374 raw0 = port->identify[100]; 1375 raw1 = port->identify[101]; 1376 raw2 = port->identify[102]; 1377 raw3 = port->identify[103]; 1378 total = raw0 | raw1<<16 | raw2<<32 | raw3<<48; 1379 *sectors = total; 1380 return (bool) !!port->identify_valid; 1381 } 1382 1383 /* 1384 * Display the identify command data. 1385 * 1386 * @port Pointer to the port data structure. 1387 * 1388 * return value 1389 * None 1390 */ 1391 static void mtip_dump_identify(struct mtip_port *port) 1392 { 1393 sector_t sectors; 1394 unsigned short revid; 1395 char cbuf[42]; 1396 1397 if (!port->identify_valid) 1398 return; 1399 1400 strscpy(cbuf, (char *)(port->identify + 10), 21); 1401 dev_info(&port->dd->pdev->dev, 1402 "Serial No.: %s\n", cbuf); 1403 1404 strscpy(cbuf, (char *)(port->identify + 23), 9); 1405 dev_info(&port->dd->pdev->dev, 1406 "Firmware Ver.: %s\n", cbuf); 1407 1408 strscpy(cbuf, (char *)(port->identify + 27), 41); 1409 dev_info(&port->dd->pdev->dev, "Model: %s\n", cbuf); 1410 1411 dev_info(&port->dd->pdev->dev, "Security: %04x %s\n", 1412 port->identify[128], 1413 port->identify[128] & 0x4 ? "(LOCKED)" : ""); 1414 1415 if (mtip_hw_get_capacity(port->dd, §ors)) 1416 dev_info(&port->dd->pdev->dev, 1417 "Capacity: %llu sectors (%llu MB)\n", 1418 (u64)sectors, 1419 ((u64)sectors) * ATA_SECT_SIZE >> 20); 1420 1421 pci_read_config_word(port->dd->pdev, PCI_REVISION_ID, &revid); 1422 switch (revid & 0xFF) { 1423 case 0x1: 1424 strscpy(cbuf, "A0", 3); 1425 break; 1426 case 0x3: 1427 strscpy(cbuf, "A2", 3); 1428 break; 1429 default: 1430 strscpy(cbuf, "?", 2); 1431 break; 1432 } 1433 dev_info(&port->dd->pdev->dev, 1434 "Card Type: %s\n", cbuf); 1435 } 1436 1437 /* 1438 * Map the commands scatter list into the command table. 1439 * 1440 * @command Pointer to the command. 1441 * @nents Number of scatter list entries. 1442 * 1443 * return value 1444 * None 1445 */ 1446 static inline void fill_command_sg(struct driver_data *dd, 1447 struct mtip_cmd *command, 1448 int nents) 1449 { 1450 int n; 1451 unsigned int dma_len; 1452 struct mtip_cmd_sg *command_sg; 1453 struct scatterlist *sg; 1454 1455 command_sg = command->command + AHCI_CMD_TBL_HDR_SZ; 1456 1457 for_each_sg(command->sg, sg, nents, n) { 1458 dma_len = sg_dma_len(sg); 1459 if (dma_len > 0x400000) 1460 dev_err(&dd->pdev->dev, 1461 "DMA segment length truncated\n"); 1462 command_sg->info = cpu_to_le32((dma_len-1) & 0x3FFFFF); 1463 command_sg->dba = cpu_to_le32(sg_dma_address(sg)); 1464 command_sg->dba_upper = 1465 cpu_to_le32((sg_dma_address(sg) >> 16) >> 16); 1466 command_sg++; 1467 } 1468 } 1469 1470 /* 1471 * @brief Execute a drive command. 1472 * 1473 * return value 0 The command completed successfully. 1474 * return value -1 An error occurred while executing the command. 1475 */ 1476 static int exec_drive_task(struct mtip_port *port, u8 *command) 1477 { 1478 struct host_to_dev_fis fis; 1479 struct host_to_dev_fis *reply = (port->rxfis + RX_FIS_D2H_REG); 1480 unsigned int to; 1481 1482 /* Build the FIS. */ 1483 memset(&fis, 0, sizeof(struct host_to_dev_fis)); 1484 fis.type = 0x27; 1485 fis.opts = 1 << 7; 1486 fis.command = command[0]; 1487 fis.features = command[1]; 1488 fis.sect_count = command[2]; 1489 fis.sector = command[3]; 1490 fis.cyl_low = command[4]; 1491 fis.cyl_hi = command[5]; 1492 fis.device = command[6] & ~0x10; /* Clear the dev bit*/ 1493 1494 mtip_set_timeout(port->dd, &fis, &to, 0); 1495 1496 dbg_printk(MTIP_DRV_NAME " %s: User Command: cmd %x, feat %x, nsect %x, sect %x, lcyl %x, hcyl %x, sel %x\n", 1497 __func__, 1498 command[0], 1499 command[1], 1500 command[2], 1501 command[3], 1502 command[4], 1503 command[5], 1504 command[6]); 1505 1506 /* Execute the command. */ 1507 if (mtip_exec_internal_command(port, 1508 &fis, 1509 5, 1510 0, 1511 0, 1512 0, 1513 to) < 0) { 1514 return -1; 1515 } 1516 1517 command[0] = reply->command; /* Status*/ 1518 command[1] = reply->features; /* Error*/ 1519 command[4] = reply->cyl_low; 1520 command[5] = reply->cyl_hi; 1521 1522 dbg_printk(MTIP_DRV_NAME " %s: Completion Status: stat %x, err %x , cyl_lo %x cyl_hi %x\n", 1523 __func__, 1524 command[0], 1525 command[1], 1526 command[4], 1527 command[5]); 1528 1529 return 0; 1530 } 1531 1532 /* 1533 * @brief Execute a drive command. 1534 * 1535 * @param port Pointer to the port data structure. 1536 * @param command Pointer to the user specified command parameters. 1537 * @param user_buffer Pointer to the user space buffer where read sector 1538 * data should be copied. 1539 * 1540 * return value 0 The command completed successfully. 1541 * return value -EFAULT An error occurred while copying the completion 1542 * data to the user space buffer. 1543 * return value -1 An error occurred while executing the command. 1544 */ 1545 static int exec_drive_command(struct mtip_port *port, u8 *command, 1546 void __user *user_buffer) 1547 { 1548 struct host_to_dev_fis fis; 1549 struct host_to_dev_fis *reply; 1550 u8 *buf = NULL; 1551 dma_addr_t dma_addr = 0; 1552 int rv = 0, xfer_sz = command[3]; 1553 unsigned int to; 1554 1555 if (xfer_sz) { 1556 if (!user_buffer) 1557 return -EFAULT; 1558 1559 buf = dma_alloc_coherent(&port->dd->pdev->dev, 1560 ATA_SECT_SIZE * xfer_sz, 1561 &dma_addr, 1562 GFP_KERNEL); 1563 if (!buf) { 1564 dev_err(&port->dd->pdev->dev, 1565 "Memory allocation failed (%d bytes)\n", 1566 ATA_SECT_SIZE * xfer_sz); 1567 return -ENOMEM; 1568 } 1569 } 1570 1571 /* Build the FIS. */ 1572 memset(&fis, 0, sizeof(struct host_to_dev_fis)); 1573 fis.type = 0x27; 1574 fis.opts = 1 << 7; 1575 fis.command = command[0]; 1576 fis.features = command[2]; 1577 fis.sect_count = command[3]; 1578 if (fis.command == ATA_CMD_SMART) { 1579 fis.sector = command[1]; 1580 fis.cyl_low = 0x4F; 1581 fis.cyl_hi = 0xC2; 1582 } 1583 1584 mtip_set_timeout(port->dd, &fis, &to, 0); 1585 1586 if (xfer_sz) 1587 reply = (port->rxfis + RX_FIS_PIO_SETUP); 1588 else 1589 reply = (port->rxfis + RX_FIS_D2H_REG); 1590 1591 dbg_printk(MTIP_DRV_NAME 1592 " %s: User Command: cmd %x, sect %x, " 1593 "feat %x, sectcnt %x\n", 1594 __func__, 1595 command[0], 1596 command[1], 1597 command[2], 1598 command[3]); 1599 1600 /* Execute the command. */ 1601 if (mtip_exec_internal_command(port, 1602 &fis, 1603 5, 1604 (xfer_sz ? dma_addr : 0), 1605 (xfer_sz ? ATA_SECT_SIZE * xfer_sz : 0), 1606 0, 1607 to) 1608 < 0) { 1609 rv = -EFAULT; 1610 goto exit_drive_command; 1611 } 1612 1613 /* Collect the completion status. */ 1614 command[0] = reply->command; /* Status*/ 1615 command[1] = reply->features; /* Error*/ 1616 command[2] = reply->sect_count; 1617 1618 dbg_printk(MTIP_DRV_NAME 1619 " %s: Completion Status: stat %x, " 1620 "err %x, nsect %x\n", 1621 __func__, 1622 command[0], 1623 command[1], 1624 command[2]); 1625 1626 if (xfer_sz) { 1627 if (copy_to_user(user_buffer, 1628 buf, 1629 ATA_SECT_SIZE * command[3])) { 1630 rv = -EFAULT; 1631 goto exit_drive_command; 1632 } 1633 } 1634 exit_drive_command: 1635 if (buf) 1636 dma_free_coherent(&port->dd->pdev->dev, 1637 ATA_SECT_SIZE * xfer_sz, buf, dma_addr); 1638 return rv; 1639 } 1640 1641 /* 1642 * Indicates whether a command has a single sector payload. 1643 * 1644 * @command passed to the device to perform the certain event. 1645 * @features passed to the device to perform the certain event. 1646 * 1647 * return value 1648 * 1 command is one that always has a single sector payload, 1649 * regardless of the value in the Sector Count field. 1650 * 0 otherwise 1651 * 1652 */ 1653 static unsigned int implicit_sector(unsigned char command, 1654 unsigned char features) 1655 { 1656 unsigned int rv = 0; 1657 1658 /* list of commands that have an implicit sector count of 1 */ 1659 switch (command) { 1660 case ATA_CMD_SEC_SET_PASS: 1661 case ATA_CMD_SEC_UNLOCK: 1662 case ATA_CMD_SEC_ERASE_PREP: 1663 case ATA_CMD_SEC_ERASE_UNIT: 1664 case ATA_CMD_SEC_FREEZE_LOCK: 1665 case ATA_CMD_SEC_DISABLE_PASS: 1666 case ATA_CMD_PMP_READ: 1667 case ATA_CMD_PMP_WRITE: 1668 rv = 1; 1669 break; 1670 case ATA_CMD_SET_MAX: 1671 if (features == ATA_SET_MAX_UNLOCK) 1672 rv = 1; 1673 break; 1674 case ATA_CMD_SMART: 1675 if ((features == ATA_SMART_READ_VALUES) || 1676 (features == ATA_SMART_READ_THRESHOLDS)) 1677 rv = 1; 1678 break; 1679 case ATA_CMD_CONF_OVERLAY: 1680 if ((features == ATA_DCO_IDENTIFY) || 1681 (features == ATA_DCO_SET)) 1682 rv = 1; 1683 break; 1684 } 1685 return rv; 1686 } 1687 1688 /* 1689 * Executes a taskfile 1690 * See ide_taskfile_ioctl() for derivation 1691 */ 1692 static int exec_drive_taskfile(struct driver_data *dd, 1693 void __user *buf, 1694 ide_task_request_t *req_task, 1695 int outtotal) 1696 { 1697 struct host_to_dev_fis fis; 1698 struct host_to_dev_fis *reply; 1699 u8 *outbuf = NULL; 1700 u8 *inbuf = NULL; 1701 dma_addr_t outbuf_dma = 0; 1702 dma_addr_t inbuf_dma = 0; 1703 dma_addr_t dma_buffer = 0; 1704 int err = 0; 1705 unsigned int taskin = 0; 1706 unsigned int taskout = 0; 1707 u8 nsect = 0; 1708 unsigned int timeout; 1709 unsigned int force_single_sector; 1710 unsigned int transfer_size; 1711 unsigned long task_file_data; 1712 int intotal = outtotal + req_task->out_size; 1713 int erasemode = 0; 1714 1715 taskout = req_task->out_size; 1716 taskin = req_task->in_size; 1717 /* 130560 = 512 * 0xFF*/ 1718 if (taskin > 130560 || taskout > 130560) 1719 return -EINVAL; 1720 1721 if (taskout) { 1722 outbuf = memdup_user(buf + outtotal, taskout); 1723 if (IS_ERR(outbuf)) 1724 return PTR_ERR(outbuf); 1725 1726 outbuf_dma = dma_map_single(&dd->pdev->dev, outbuf, 1727 taskout, DMA_TO_DEVICE); 1728 if (dma_mapping_error(&dd->pdev->dev, outbuf_dma)) { 1729 err = -ENOMEM; 1730 goto abort; 1731 } 1732 dma_buffer = outbuf_dma; 1733 } 1734 1735 if (taskin) { 1736 inbuf = memdup_user(buf + intotal, taskin); 1737 if (IS_ERR(inbuf)) { 1738 err = PTR_ERR(inbuf); 1739 inbuf = NULL; 1740 goto abort; 1741 } 1742 inbuf_dma = dma_map_single(&dd->pdev->dev, inbuf, 1743 taskin, DMA_FROM_DEVICE); 1744 if (dma_mapping_error(&dd->pdev->dev, inbuf_dma)) { 1745 err = -ENOMEM; 1746 goto abort; 1747 } 1748 dma_buffer = inbuf_dma; 1749 } 1750 1751 /* only supports PIO and non-data commands from this ioctl. */ 1752 switch (req_task->data_phase) { 1753 case TASKFILE_OUT: 1754 nsect = taskout / ATA_SECT_SIZE; 1755 reply = (dd->port->rxfis + RX_FIS_PIO_SETUP); 1756 break; 1757 case TASKFILE_IN: 1758 reply = (dd->port->rxfis + RX_FIS_PIO_SETUP); 1759 break; 1760 case TASKFILE_NO_DATA: 1761 reply = (dd->port->rxfis + RX_FIS_D2H_REG); 1762 break; 1763 default: 1764 err = -EINVAL; 1765 goto abort; 1766 } 1767 1768 /* Build the FIS. */ 1769 memset(&fis, 0, sizeof(struct host_to_dev_fis)); 1770 1771 fis.type = 0x27; 1772 fis.opts = 1 << 7; 1773 fis.command = req_task->io_ports[7]; 1774 fis.features = req_task->io_ports[1]; 1775 fis.sect_count = req_task->io_ports[2]; 1776 fis.lba_low = req_task->io_ports[3]; 1777 fis.lba_mid = req_task->io_ports[4]; 1778 fis.lba_hi = req_task->io_ports[5]; 1779 /* Clear the dev bit*/ 1780 fis.device = req_task->io_ports[6] & ~0x10; 1781 1782 if ((req_task->in_flags.all == 0) && (req_task->out_flags.all & 1)) { 1783 req_task->in_flags.all = 1784 IDE_TASKFILE_STD_IN_FLAGS | 1785 (IDE_HOB_STD_IN_FLAGS << 8); 1786 fis.lba_low_ex = req_task->hob_ports[3]; 1787 fis.lba_mid_ex = req_task->hob_ports[4]; 1788 fis.lba_hi_ex = req_task->hob_ports[5]; 1789 fis.features_ex = req_task->hob_ports[1]; 1790 fis.sect_cnt_ex = req_task->hob_ports[2]; 1791 1792 } else { 1793 req_task->in_flags.all = IDE_TASKFILE_STD_IN_FLAGS; 1794 } 1795 1796 force_single_sector = implicit_sector(fis.command, fis.features); 1797 1798 if ((taskin || taskout) && (!fis.sect_count)) { 1799 if (nsect) 1800 fis.sect_count = nsect; 1801 else { 1802 if (!force_single_sector) { 1803 dev_warn(&dd->pdev->dev, 1804 "data movement but " 1805 "sect_count is 0\n"); 1806 err = -EINVAL; 1807 goto abort; 1808 } 1809 } 1810 } 1811 1812 dbg_printk(MTIP_DRV_NAME 1813 " %s: cmd %x, feat %x, nsect %x," 1814 " sect/lbal %x, lcyl/lbam %x, hcyl/lbah %x," 1815 " head/dev %x\n", 1816 __func__, 1817 fis.command, 1818 fis.features, 1819 fis.sect_count, 1820 fis.lba_low, 1821 fis.lba_mid, 1822 fis.lba_hi, 1823 fis.device); 1824 1825 /* check for erase mode support during secure erase.*/ 1826 if ((fis.command == ATA_CMD_SEC_ERASE_UNIT) && outbuf && 1827 (outbuf[0] & MTIP_SEC_ERASE_MODE)) { 1828 erasemode = 1; 1829 } 1830 1831 mtip_set_timeout(dd, &fis, &timeout, erasemode); 1832 1833 /* Determine the correct transfer size.*/ 1834 if (force_single_sector) 1835 transfer_size = ATA_SECT_SIZE; 1836 else 1837 transfer_size = ATA_SECT_SIZE * fis.sect_count; 1838 1839 /* Execute the command.*/ 1840 if (mtip_exec_internal_command(dd->port, 1841 &fis, 1842 5, 1843 dma_buffer, 1844 transfer_size, 1845 0, 1846 timeout) < 0) { 1847 err = -EIO; 1848 goto abort; 1849 } 1850 1851 task_file_data = readl(dd->port->mmio+PORT_TFDATA); 1852 1853 if ((req_task->data_phase == TASKFILE_IN) && !(task_file_data & 1)) { 1854 reply = dd->port->rxfis + RX_FIS_PIO_SETUP; 1855 req_task->io_ports[7] = reply->control; 1856 } else { 1857 reply = dd->port->rxfis + RX_FIS_D2H_REG; 1858 req_task->io_ports[7] = reply->command; 1859 } 1860 1861 /* reclaim the DMA buffers.*/ 1862 if (inbuf_dma) 1863 dma_unmap_single(&dd->pdev->dev, inbuf_dma, taskin, 1864 DMA_FROM_DEVICE); 1865 if (outbuf_dma) 1866 dma_unmap_single(&dd->pdev->dev, outbuf_dma, taskout, 1867 DMA_TO_DEVICE); 1868 inbuf_dma = 0; 1869 outbuf_dma = 0; 1870 1871 /* return the ATA registers to the caller.*/ 1872 req_task->io_ports[1] = reply->features; 1873 req_task->io_ports[2] = reply->sect_count; 1874 req_task->io_ports[3] = reply->lba_low; 1875 req_task->io_ports[4] = reply->lba_mid; 1876 req_task->io_ports[5] = reply->lba_hi; 1877 req_task->io_ports[6] = reply->device; 1878 1879 if (req_task->out_flags.all & 1) { 1880 1881 req_task->hob_ports[3] = reply->lba_low_ex; 1882 req_task->hob_ports[4] = reply->lba_mid_ex; 1883 req_task->hob_ports[5] = reply->lba_hi_ex; 1884 req_task->hob_ports[1] = reply->features_ex; 1885 req_task->hob_ports[2] = reply->sect_cnt_ex; 1886 } 1887 dbg_printk(MTIP_DRV_NAME 1888 " %s: Completion: stat %x," 1889 "err %x, sect_cnt %x, lbalo %x," 1890 "lbamid %x, lbahi %x, dev %x\n", 1891 __func__, 1892 req_task->io_ports[7], 1893 req_task->io_ports[1], 1894 req_task->io_ports[2], 1895 req_task->io_ports[3], 1896 req_task->io_ports[4], 1897 req_task->io_ports[5], 1898 req_task->io_ports[6]); 1899 1900 if (taskout) { 1901 if (copy_to_user(buf + outtotal, outbuf, taskout)) { 1902 err = -EFAULT; 1903 goto abort; 1904 } 1905 } 1906 if (taskin) { 1907 if (copy_to_user(buf + intotal, inbuf, taskin)) { 1908 err = -EFAULT; 1909 goto abort; 1910 } 1911 } 1912 abort: 1913 if (inbuf_dma) 1914 dma_unmap_single(&dd->pdev->dev, inbuf_dma, taskin, 1915 DMA_FROM_DEVICE); 1916 if (outbuf_dma) 1917 dma_unmap_single(&dd->pdev->dev, outbuf_dma, taskout, 1918 DMA_TO_DEVICE); 1919 kfree(outbuf); 1920 kfree(inbuf); 1921 1922 return err; 1923 } 1924 1925 /* 1926 * Handle IOCTL calls from the Block Layer. 1927 * 1928 * This function is called by the Block Layer when it receives an IOCTL 1929 * command that it does not understand. If the IOCTL command is not supported 1930 * this function returns -ENOTTY. 1931 * 1932 * @dd Pointer to the driver data structure. 1933 * @cmd IOCTL command passed from the Block Layer. 1934 * @arg IOCTL argument passed from the Block Layer. 1935 * 1936 * return value 1937 * 0 The IOCTL completed successfully. 1938 * -ENOTTY The specified command is not supported. 1939 * -EFAULT An error occurred copying data to a user space buffer. 1940 * -EIO An error occurred while executing the command. 1941 */ 1942 static int mtip_hw_ioctl(struct driver_data *dd, unsigned int cmd, 1943 unsigned long arg) 1944 { 1945 switch (cmd) { 1946 case HDIO_GET_IDENTITY: 1947 { 1948 if (copy_to_user((void __user *)arg, dd->port->identify, 1949 sizeof(u16) * ATA_ID_WORDS)) 1950 return -EFAULT; 1951 break; 1952 } 1953 case HDIO_DRIVE_CMD: 1954 { 1955 u8 drive_command[4]; 1956 1957 /* Copy the user command info to our buffer. */ 1958 if (copy_from_user(drive_command, 1959 (void __user *) arg, 1960 sizeof(drive_command))) 1961 return -EFAULT; 1962 1963 /* Execute the drive command. */ 1964 if (exec_drive_command(dd->port, 1965 drive_command, 1966 (void __user *) (arg+4))) 1967 return -EIO; 1968 1969 /* Copy the status back to the users buffer. */ 1970 if (copy_to_user((void __user *) arg, 1971 drive_command, 1972 sizeof(drive_command))) 1973 return -EFAULT; 1974 1975 break; 1976 } 1977 case HDIO_DRIVE_TASK: 1978 { 1979 u8 drive_command[7]; 1980 1981 /* Copy the user command info to our buffer. */ 1982 if (copy_from_user(drive_command, 1983 (void __user *) arg, 1984 sizeof(drive_command))) 1985 return -EFAULT; 1986 1987 /* Execute the drive command. */ 1988 if (exec_drive_task(dd->port, drive_command)) 1989 return -EIO; 1990 1991 /* Copy the status back to the users buffer. */ 1992 if (copy_to_user((void __user *) arg, 1993 drive_command, 1994 sizeof(drive_command))) 1995 return -EFAULT; 1996 1997 break; 1998 } 1999 case HDIO_DRIVE_TASKFILE: { 2000 ide_task_request_t req_task; 2001 int ret, outtotal; 2002 2003 if (copy_from_user(&req_task, (void __user *) arg, 2004 sizeof(req_task))) 2005 return -EFAULT; 2006 2007 outtotal = sizeof(req_task); 2008 2009 ret = exec_drive_taskfile(dd, (void __user *) arg, 2010 &req_task, outtotal); 2011 2012 if (copy_to_user((void __user *) arg, &req_task, 2013 sizeof(req_task))) 2014 return -EFAULT; 2015 2016 return ret; 2017 } 2018 2019 default: 2020 return -EINVAL; 2021 } 2022 return 0; 2023 } 2024 2025 /* 2026 * Submit an IO to the hw 2027 * 2028 * This function is called by the block layer to issue an io 2029 * to the device. Upon completion, the callback function will 2030 * be called with the data parameter passed as the callback data. 2031 * 2032 * @dd Pointer to the driver data structure. 2033 * @start First sector to read. 2034 * @nsect Number of sectors to read. 2035 * @tag The tag of this read command. 2036 * @callback Pointer to the function that should be called 2037 * when the read completes. 2038 * @data Callback data passed to the callback function 2039 * when the read completes. 2040 * @dir Direction (read or write) 2041 * 2042 * return value 2043 * None 2044 */ 2045 static void mtip_hw_submit_io(struct driver_data *dd, struct request *rq, 2046 struct mtip_cmd *command, 2047 struct blk_mq_hw_ctx *hctx) 2048 { 2049 struct mtip_cmd_hdr *hdr = 2050 dd->port->command_list + sizeof(struct mtip_cmd_hdr) * rq->tag; 2051 struct host_to_dev_fis *fis; 2052 struct mtip_port *port = dd->port; 2053 int dma_dir = rq_data_dir(rq) == READ ? DMA_FROM_DEVICE : DMA_TO_DEVICE; 2054 u64 start = blk_rq_pos(rq); 2055 unsigned int nsect = blk_rq_sectors(rq); 2056 unsigned int nents; 2057 2058 /* Map the scatter list for DMA access */ 2059 nents = blk_rq_map_sg(hctx->queue, rq, command->sg); 2060 nents = dma_map_sg(&dd->pdev->dev, command->sg, nents, dma_dir); 2061 2062 prefetch(&port->flags); 2063 2064 command->scatter_ents = nents; 2065 2066 /* 2067 * The number of retries for this command before it is 2068 * reported as a failure to the upper layers. 2069 */ 2070 command->retries = MTIP_MAX_RETRIES; 2071 2072 /* Fill out fis */ 2073 fis = command->command; 2074 fis->type = 0x27; 2075 fis->opts = 1 << 7; 2076 if (dma_dir == DMA_FROM_DEVICE) 2077 fis->command = ATA_CMD_FPDMA_READ; 2078 else 2079 fis->command = ATA_CMD_FPDMA_WRITE; 2080 fis->lba_low = start & 0xFF; 2081 fis->lba_mid = (start >> 8) & 0xFF; 2082 fis->lba_hi = (start >> 16) & 0xFF; 2083 fis->lba_low_ex = (start >> 24) & 0xFF; 2084 fis->lba_mid_ex = (start >> 32) & 0xFF; 2085 fis->lba_hi_ex = (start >> 40) & 0xFF; 2086 fis->device = 1 << 6; 2087 fis->features = nsect & 0xFF; 2088 fis->features_ex = (nsect >> 8) & 0xFF; 2089 fis->sect_count = ((rq->tag << 3) | (rq->tag >> 5)); 2090 fis->sect_cnt_ex = 0; 2091 fis->control = 0; 2092 fis->res2 = 0; 2093 fis->res3 = 0; 2094 fill_command_sg(dd, command, nents); 2095 2096 if (unlikely(command->unaligned)) 2097 fis->device |= 1 << 7; 2098 2099 /* Populate the command header */ 2100 hdr->ctba = cpu_to_le32(command->command_dma & 0xFFFFFFFF); 2101 if (test_bit(MTIP_PF_HOST_CAP_64, &dd->port->flags)) 2102 hdr->ctbau = cpu_to_le32((command->command_dma >> 16) >> 16); 2103 hdr->opts = cpu_to_le32((nents << 16) | 5 | AHCI_CMD_PREFETCH); 2104 hdr->byte_count = 0; 2105 2106 command->direction = dma_dir; 2107 2108 /* 2109 * To prevent this command from being issued 2110 * if an internal command is in progress or error handling is active. 2111 */ 2112 if (unlikely(port->flags & MTIP_PF_PAUSE_IO)) { 2113 set_bit(rq->tag, port->cmds_to_issue); 2114 set_bit(MTIP_PF_ISSUE_CMDS_BIT, &port->flags); 2115 return; 2116 } 2117 2118 /* Issue the command to the hardware */ 2119 mtip_issue_ncq_command(port, rq->tag); 2120 } 2121 2122 /* 2123 * Sysfs status dump. 2124 * 2125 * @dev Pointer to the device structure, passed by the kernrel. 2126 * @attr Pointer to the device_attribute structure passed by the kernel. 2127 * @buf Pointer to the char buffer that will receive the stats info. 2128 * 2129 * return value 2130 * The size, in bytes, of the data copied into buf. 2131 */ 2132 static ssize_t mtip_hw_show_status(struct device *dev, 2133 struct device_attribute *attr, 2134 char *buf) 2135 { 2136 struct driver_data *dd = dev_to_disk(dev)->private_data; 2137 int size = 0; 2138 2139 if (test_bit(MTIP_DDF_OVER_TEMP_BIT, &dd->dd_flag)) 2140 size += sprintf(buf, "%s", "thermal_shutdown\n"); 2141 else if (test_bit(MTIP_DDF_WRITE_PROTECT_BIT, &dd->dd_flag)) 2142 size += sprintf(buf, "%s", "write_protect\n"); 2143 else 2144 size += sprintf(buf, "%s", "online\n"); 2145 2146 return size; 2147 } 2148 2149 static DEVICE_ATTR(status, 0444, mtip_hw_show_status, NULL); 2150 2151 static struct attribute *mtip_disk_attrs[] = { 2152 &dev_attr_status.attr, 2153 NULL, 2154 }; 2155 2156 static const struct attribute_group mtip_disk_attr_group = { 2157 .attrs = mtip_disk_attrs, 2158 }; 2159 2160 static const struct attribute_group *mtip_disk_attr_groups[] = { 2161 &mtip_disk_attr_group, 2162 NULL, 2163 }; 2164 2165 static ssize_t mtip_hw_read_registers(struct file *f, char __user *ubuf, 2166 size_t len, loff_t *offset) 2167 { 2168 struct driver_data *dd = (struct driver_data *)f->private_data; 2169 char *buf; 2170 u32 group_allocated; 2171 int size = *offset; 2172 int n, rv = 0; 2173 2174 if (!len || size) 2175 return 0; 2176 2177 buf = kzalloc(MTIP_DFS_MAX_BUF_SIZE, GFP_KERNEL); 2178 if (!buf) 2179 return -ENOMEM; 2180 2181 size += sprintf(&buf[size], "H/ S ACTive : [ 0x"); 2182 2183 for (n = dd->slot_groups-1; n >= 0; n--) 2184 size += sprintf(&buf[size], "%08X ", 2185 readl(dd->port->s_active[n])); 2186 2187 size += sprintf(&buf[size], "]\n"); 2188 size += sprintf(&buf[size], "H/ Command Issue : [ 0x"); 2189 2190 for (n = dd->slot_groups-1; n >= 0; n--) 2191 size += sprintf(&buf[size], "%08X ", 2192 readl(dd->port->cmd_issue[n])); 2193 2194 size += sprintf(&buf[size], "]\n"); 2195 size += sprintf(&buf[size], "H/ Completed : [ 0x"); 2196 2197 for (n = dd->slot_groups-1; n >= 0; n--) 2198 size += sprintf(&buf[size], "%08X ", 2199 readl(dd->port->completed[n])); 2200 2201 size += sprintf(&buf[size], "]\n"); 2202 size += sprintf(&buf[size], "H/ PORT IRQ STAT : [ 0x%08X ]\n", 2203 readl(dd->port->mmio + PORT_IRQ_STAT)); 2204 size += sprintf(&buf[size], "H/ HOST IRQ STAT : [ 0x%08X ]\n", 2205 readl(dd->mmio + HOST_IRQ_STAT)); 2206 size += sprintf(&buf[size], "\n"); 2207 2208 size += sprintf(&buf[size], "L/ Commands in Q : [ 0x"); 2209 2210 for (n = dd->slot_groups-1; n >= 0; n--) { 2211 if (sizeof(long) > sizeof(u32)) 2212 group_allocated = 2213 dd->port->cmds_to_issue[n/2] >> (32*(n&1)); 2214 else 2215 group_allocated = dd->port->cmds_to_issue[n]; 2216 size += sprintf(&buf[size], "%08X ", group_allocated); 2217 } 2218 size += sprintf(&buf[size], "]\n"); 2219 2220 *offset = size <= len ? size : len; 2221 size = copy_to_user(ubuf, buf, *offset); 2222 if (size) 2223 rv = -EFAULT; 2224 2225 kfree(buf); 2226 return rv ? rv : *offset; 2227 } 2228 2229 static ssize_t mtip_hw_read_flags(struct file *f, char __user *ubuf, 2230 size_t len, loff_t *offset) 2231 { 2232 struct driver_data *dd = (struct driver_data *)f->private_data; 2233 char *buf; 2234 int size = *offset; 2235 int rv = 0; 2236 2237 if (!len || size) 2238 return 0; 2239 2240 buf = kzalloc(MTIP_DFS_MAX_BUF_SIZE, GFP_KERNEL); 2241 if (!buf) 2242 return -ENOMEM; 2243 2244 size += sprintf(&buf[size], "Flag-port : [ %08lX ]\n", 2245 dd->port->flags); 2246 size += sprintf(&buf[size], "Flag-dd : [ %08lX ]\n", 2247 dd->dd_flag); 2248 2249 *offset = size <= len ? size : len; 2250 size = copy_to_user(ubuf, buf, *offset); 2251 if (size) 2252 rv = -EFAULT; 2253 2254 kfree(buf); 2255 return rv ? rv : *offset; 2256 } 2257 2258 static const struct file_operations mtip_regs_fops = { 2259 .owner = THIS_MODULE, 2260 .open = simple_open, 2261 .read = mtip_hw_read_registers, 2262 .llseek = no_llseek, 2263 }; 2264 2265 static const struct file_operations mtip_flags_fops = { 2266 .owner = THIS_MODULE, 2267 .open = simple_open, 2268 .read = mtip_hw_read_flags, 2269 .llseek = no_llseek, 2270 }; 2271 2272 static int mtip_hw_debugfs_init(struct driver_data *dd) 2273 { 2274 if (!dfs_parent) 2275 return -1; 2276 2277 dd->dfs_node = debugfs_create_dir(dd->disk->disk_name, dfs_parent); 2278 if (IS_ERR_OR_NULL(dd->dfs_node)) { 2279 dev_warn(&dd->pdev->dev, 2280 "Error creating node %s under debugfs\n", 2281 dd->disk->disk_name); 2282 dd->dfs_node = NULL; 2283 return -1; 2284 } 2285 2286 debugfs_create_file("flags", 0444, dd->dfs_node, dd, &mtip_flags_fops); 2287 debugfs_create_file("registers", 0444, dd->dfs_node, dd, 2288 &mtip_regs_fops); 2289 2290 return 0; 2291 } 2292 2293 static void mtip_hw_debugfs_exit(struct driver_data *dd) 2294 { 2295 debugfs_remove_recursive(dd->dfs_node); 2296 } 2297 2298 /* 2299 * Perform any init/resume time hardware setup 2300 * 2301 * @dd Pointer to the driver data structure. 2302 * 2303 * return value 2304 * None 2305 */ 2306 static inline void hba_setup(struct driver_data *dd) 2307 { 2308 u32 hwdata; 2309 hwdata = readl(dd->mmio + HOST_HSORG); 2310 2311 /* interrupt bug workaround: use only 1 IS bit.*/ 2312 writel(hwdata | 2313 HSORG_DISABLE_SLOTGRP_INTR | 2314 HSORG_DISABLE_SLOTGRP_PXIS, 2315 dd->mmio + HOST_HSORG); 2316 } 2317 2318 static int mtip_device_unaligned_constrained(struct driver_data *dd) 2319 { 2320 return (dd->pdev->device == P420M_DEVICE_ID ? 1 : 0); 2321 } 2322 2323 /* 2324 * Detect the details of the product, and store anything needed 2325 * into the driver data structure. This includes product type and 2326 * version and number of slot groups. 2327 * 2328 * @dd Pointer to the driver data structure. 2329 * 2330 * return value 2331 * None 2332 */ 2333 static void mtip_detect_product(struct driver_data *dd) 2334 { 2335 u32 hwdata; 2336 unsigned int rev, slotgroups; 2337 2338 /* 2339 * HBA base + 0xFC [15:0] - vendor-specific hardware interface 2340 * info register: 2341 * [15:8] hardware/software interface rev# 2342 * [ 3] asic-style interface 2343 * [ 2:0] number of slot groups, minus 1 (only valid for asic-style). 2344 */ 2345 hwdata = readl(dd->mmio + HOST_HSORG); 2346 2347 dd->product_type = MTIP_PRODUCT_UNKNOWN; 2348 dd->slot_groups = 1; 2349 2350 if (hwdata & 0x8) { 2351 dd->product_type = MTIP_PRODUCT_ASICFPGA; 2352 rev = (hwdata & HSORG_HWREV) >> 8; 2353 slotgroups = (hwdata & HSORG_SLOTGROUPS) + 1; 2354 dev_info(&dd->pdev->dev, 2355 "ASIC-FPGA design, HS rev 0x%x, " 2356 "%i slot groups [%i slots]\n", 2357 rev, 2358 slotgroups, 2359 slotgroups * 32); 2360 2361 if (slotgroups > MTIP_MAX_SLOT_GROUPS) { 2362 dev_warn(&dd->pdev->dev, 2363 "Warning: driver only supports " 2364 "%i slot groups.\n", MTIP_MAX_SLOT_GROUPS); 2365 slotgroups = MTIP_MAX_SLOT_GROUPS; 2366 } 2367 dd->slot_groups = slotgroups; 2368 return; 2369 } 2370 2371 dev_warn(&dd->pdev->dev, "Unrecognized product id\n"); 2372 } 2373 2374 /* 2375 * Blocking wait for FTL rebuild to complete 2376 * 2377 * @dd Pointer to the DRIVER_DATA structure. 2378 * 2379 * return value 2380 * 0 FTL rebuild completed successfully 2381 * -EFAULT FTL rebuild error/timeout/interruption 2382 */ 2383 static int mtip_ftl_rebuild_poll(struct driver_data *dd) 2384 { 2385 unsigned long timeout, cnt = 0, start; 2386 2387 dev_warn(&dd->pdev->dev, 2388 "FTL rebuild in progress. Polling for completion.\n"); 2389 2390 start = jiffies; 2391 timeout = jiffies + msecs_to_jiffies(MTIP_FTL_REBUILD_TIMEOUT_MS); 2392 2393 do { 2394 if (unlikely(test_bit(MTIP_DDF_REMOVE_PENDING_BIT, 2395 &dd->dd_flag))) 2396 return -EFAULT; 2397 if (mtip_check_surprise_removal(dd)) 2398 return -EFAULT; 2399 2400 if (mtip_get_identify(dd->port, NULL) < 0) 2401 return -EFAULT; 2402 2403 if (*(dd->port->identify + MTIP_FTL_REBUILD_OFFSET) == 2404 MTIP_FTL_REBUILD_MAGIC) { 2405 ssleep(1); 2406 /* Print message every 3 minutes */ 2407 if (cnt++ >= 180) { 2408 dev_warn(&dd->pdev->dev, 2409 "FTL rebuild in progress (%d secs).\n", 2410 jiffies_to_msecs(jiffies - start) / 1000); 2411 cnt = 0; 2412 } 2413 } else { 2414 dev_warn(&dd->pdev->dev, 2415 "FTL rebuild complete (%d secs).\n", 2416 jiffies_to_msecs(jiffies - start) / 1000); 2417 mtip_block_initialize(dd); 2418 return 0; 2419 } 2420 } while (time_before(jiffies, timeout)); 2421 2422 /* Check for timeout */ 2423 dev_err(&dd->pdev->dev, 2424 "Timed out waiting for FTL rebuild to complete (%d secs).\n", 2425 jiffies_to_msecs(jiffies - start) / 1000); 2426 return -EFAULT; 2427 } 2428 2429 static void mtip_softirq_done_fn(struct request *rq) 2430 { 2431 struct mtip_cmd *cmd = blk_mq_rq_to_pdu(rq); 2432 struct driver_data *dd = rq->q->queuedata; 2433 2434 /* Unmap the DMA scatter list entries */ 2435 dma_unmap_sg(&dd->pdev->dev, cmd->sg, cmd->scatter_ents, 2436 cmd->direction); 2437 2438 if (unlikely(cmd->unaligned)) 2439 atomic_inc(&dd->port->cmd_slot_unal); 2440 2441 blk_mq_end_request(rq, cmd->status); 2442 } 2443 2444 static bool mtip_abort_cmd(struct request *req, void *data) 2445 { 2446 struct mtip_cmd *cmd = blk_mq_rq_to_pdu(req); 2447 struct driver_data *dd = data; 2448 2449 dbg_printk(MTIP_DRV_NAME " Aborting request, tag = %d\n", req->tag); 2450 2451 clear_bit(req->tag, dd->port->cmds_to_issue); 2452 cmd->status = BLK_STS_IOERR; 2453 mtip_softirq_done_fn(req); 2454 return true; 2455 } 2456 2457 static bool mtip_queue_cmd(struct request *req, void *data) 2458 { 2459 struct driver_data *dd = data; 2460 2461 set_bit(req->tag, dd->port->cmds_to_issue); 2462 blk_abort_request(req); 2463 return true; 2464 } 2465 2466 /* 2467 * service thread to issue queued commands 2468 * 2469 * @data Pointer to the driver data structure. 2470 * 2471 * return value 2472 * 0 2473 */ 2474 2475 static int mtip_service_thread(void *data) 2476 { 2477 struct driver_data *dd = (struct driver_data *)data; 2478 unsigned long slot, slot_start, slot_wrap, to; 2479 unsigned int num_cmd_slots = dd->slot_groups * 32; 2480 struct mtip_port *port = dd->port; 2481 2482 while (1) { 2483 if (kthread_should_stop() || 2484 test_bit(MTIP_PF_SVC_THD_STOP_BIT, &port->flags)) 2485 goto st_out; 2486 clear_bit(MTIP_PF_SVC_THD_ACTIVE_BIT, &port->flags); 2487 2488 /* 2489 * the condition is to check neither an internal command is 2490 * is in progress nor error handling is active 2491 */ 2492 wait_event_interruptible(port->svc_wait, (port->flags) && 2493 (port->flags & MTIP_PF_SVC_THD_WORK)); 2494 2495 if (kthread_should_stop() || 2496 test_bit(MTIP_PF_SVC_THD_STOP_BIT, &port->flags)) 2497 goto st_out; 2498 2499 if (unlikely(test_bit(MTIP_DDF_REMOVE_PENDING_BIT, 2500 &dd->dd_flag))) 2501 goto st_out; 2502 2503 set_bit(MTIP_PF_SVC_THD_ACTIVE_BIT, &port->flags); 2504 2505 restart_eh: 2506 /* Demux bits: start with error handling */ 2507 if (test_bit(MTIP_PF_EH_ACTIVE_BIT, &port->flags)) { 2508 mtip_handle_tfe(dd); 2509 clear_bit(MTIP_PF_EH_ACTIVE_BIT, &port->flags); 2510 } 2511 2512 if (test_bit(MTIP_PF_EH_ACTIVE_BIT, &port->flags)) 2513 goto restart_eh; 2514 2515 if (test_bit(MTIP_PF_TO_ACTIVE_BIT, &port->flags)) { 2516 to = jiffies + msecs_to_jiffies(5000); 2517 2518 do { 2519 mdelay(100); 2520 } while (atomic_read(&dd->irq_workers_active) != 0 && 2521 time_before(jiffies, to)); 2522 2523 if (atomic_read(&dd->irq_workers_active) != 0) 2524 dev_warn(&dd->pdev->dev, 2525 "Completion workers still active!"); 2526 2527 blk_mq_quiesce_queue(dd->queue); 2528 2529 blk_mq_tagset_busy_iter(&dd->tags, mtip_queue_cmd, dd); 2530 2531 set_bit(MTIP_PF_ISSUE_CMDS_BIT, &dd->port->flags); 2532 2533 if (mtip_device_reset(dd)) 2534 blk_mq_tagset_busy_iter(&dd->tags, 2535 mtip_abort_cmd, dd); 2536 2537 clear_bit(MTIP_PF_TO_ACTIVE_BIT, &dd->port->flags); 2538 2539 blk_mq_unquiesce_queue(dd->queue); 2540 } 2541 2542 if (test_bit(MTIP_PF_ISSUE_CMDS_BIT, &port->flags)) { 2543 slot = 1; 2544 /* used to restrict the loop to one iteration */ 2545 slot_start = num_cmd_slots; 2546 slot_wrap = 0; 2547 while (1) { 2548 slot = find_next_bit(port->cmds_to_issue, 2549 num_cmd_slots, slot); 2550 if (slot_wrap == 1) { 2551 if ((slot_start >= slot) || 2552 (slot >= num_cmd_slots)) 2553 break; 2554 } 2555 if (unlikely(slot_start == num_cmd_slots)) 2556 slot_start = slot; 2557 2558 if (unlikely(slot == num_cmd_slots)) { 2559 slot = 1; 2560 slot_wrap = 1; 2561 continue; 2562 } 2563 2564 /* Issue the command to the hardware */ 2565 mtip_issue_ncq_command(port, slot); 2566 2567 clear_bit(slot, port->cmds_to_issue); 2568 } 2569 2570 clear_bit(MTIP_PF_ISSUE_CMDS_BIT, &port->flags); 2571 } 2572 2573 if (test_bit(MTIP_PF_REBUILD_BIT, &port->flags)) { 2574 if (mtip_ftl_rebuild_poll(dd) == 0) 2575 clear_bit(MTIP_PF_REBUILD_BIT, &port->flags); 2576 } 2577 } 2578 2579 st_out: 2580 return 0; 2581 } 2582 2583 /* 2584 * DMA region teardown 2585 * 2586 * @dd Pointer to driver_data structure 2587 * 2588 * return value 2589 * None 2590 */ 2591 static void mtip_dma_free(struct driver_data *dd) 2592 { 2593 struct mtip_port *port = dd->port; 2594 2595 if (port->block1) 2596 dma_free_coherent(&dd->pdev->dev, BLOCK_DMA_ALLOC_SZ, 2597 port->block1, port->block1_dma); 2598 2599 if (port->command_list) { 2600 dma_free_coherent(&dd->pdev->dev, AHCI_CMD_TBL_SZ, 2601 port->command_list, port->command_list_dma); 2602 } 2603 } 2604 2605 /* 2606 * DMA region setup 2607 * 2608 * @dd Pointer to driver_data structure 2609 * 2610 * return value 2611 * -ENOMEM Not enough free DMA region space to initialize driver 2612 */ 2613 static int mtip_dma_alloc(struct driver_data *dd) 2614 { 2615 struct mtip_port *port = dd->port; 2616 2617 /* Allocate dma memory for RX Fis, Identify, and Sector Buffer */ 2618 port->block1 = 2619 dma_alloc_coherent(&dd->pdev->dev, BLOCK_DMA_ALLOC_SZ, 2620 &port->block1_dma, GFP_KERNEL); 2621 if (!port->block1) 2622 return -ENOMEM; 2623 2624 /* Allocate dma memory for command list */ 2625 port->command_list = 2626 dma_alloc_coherent(&dd->pdev->dev, AHCI_CMD_TBL_SZ, 2627 &port->command_list_dma, GFP_KERNEL); 2628 if (!port->command_list) { 2629 dma_free_coherent(&dd->pdev->dev, BLOCK_DMA_ALLOC_SZ, 2630 port->block1, port->block1_dma); 2631 port->block1 = NULL; 2632 port->block1_dma = 0; 2633 return -ENOMEM; 2634 } 2635 2636 /* Setup all pointers into first DMA region */ 2637 port->rxfis = port->block1 + AHCI_RX_FIS_OFFSET; 2638 port->rxfis_dma = port->block1_dma + AHCI_RX_FIS_OFFSET; 2639 port->identify = port->block1 + AHCI_IDFY_OFFSET; 2640 port->identify_dma = port->block1_dma + AHCI_IDFY_OFFSET; 2641 port->log_buf = port->block1 + AHCI_SECTBUF_OFFSET; 2642 port->log_buf_dma = port->block1_dma + AHCI_SECTBUF_OFFSET; 2643 port->smart_buf = port->block1 + AHCI_SMARTBUF_OFFSET; 2644 port->smart_buf_dma = port->block1_dma + AHCI_SMARTBUF_OFFSET; 2645 2646 return 0; 2647 } 2648 2649 static int mtip_hw_get_identify(struct driver_data *dd) 2650 { 2651 struct smart_attr attr242; 2652 unsigned char *buf; 2653 int rv; 2654 2655 if (mtip_get_identify(dd->port, NULL) < 0) 2656 return -EFAULT; 2657 2658 if (*(dd->port->identify + MTIP_FTL_REBUILD_OFFSET) == 2659 MTIP_FTL_REBUILD_MAGIC) { 2660 set_bit(MTIP_PF_REBUILD_BIT, &dd->port->flags); 2661 return MTIP_FTL_REBUILD_MAGIC; 2662 } 2663 mtip_dump_identify(dd->port); 2664 2665 /* check write protect, over temp and rebuild statuses */ 2666 rv = mtip_read_log_page(dd->port, ATA_LOG_SATA_NCQ, 2667 dd->port->log_buf, 2668 dd->port->log_buf_dma, 1); 2669 if (rv) { 2670 dev_warn(&dd->pdev->dev, 2671 "Error in READ LOG EXT (10h) command\n"); 2672 /* non-critical error, don't fail the load */ 2673 } else { 2674 buf = (unsigned char *)dd->port->log_buf; 2675 if (buf[259] & 0x1) { 2676 dev_info(&dd->pdev->dev, 2677 "Write protect bit is set.\n"); 2678 set_bit(MTIP_DDF_WRITE_PROTECT_BIT, &dd->dd_flag); 2679 } 2680 if (buf[288] == 0xF7) { 2681 dev_info(&dd->pdev->dev, 2682 "Exceeded Tmax, drive in thermal shutdown.\n"); 2683 set_bit(MTIP_DDF_OVER_TEMP_BIT, &dd->dd_flag); 2684 } 2685 if (buf[288] == 0xBF) { 2686 dev_info(&dd->pdev->dev, 2687 "Drive indicates rebuild has failed.\n"); 2688 set_bit(MTIP_DDF_REBUILD_FAILED_BIT, &dd->dd_flag); 2689 } 2690 } 2691 2692 /* get write protect progess */ 2693 memset(&attr242, 0, sizeof(struct smart_attr)); 2694 if (mtip_get_smart_attr(dd->port, 242, &attr242)) 2695 dev_warn(&dd->pdev->dev, 2696 "Unable to check write protect progress\n"); 2697 else 2698 dev_info(&dd->pdev->dev, 2699 "Write protect progress: %u%% (%u blocks)\n", 2700 attr242.cur, le32_to_cpu(attr242.data)); 2701 2702 return rv; 2703 } 2704 2705 /* 2706 * Called once for each card. 2707 * 2708 * @dd Pointer to the driver data structure. 2709 * 2710 * return value 2711 * 0 on success, else an error code. 2712 */ 2713 static int mtip_hw_init(struct driver_data *dd) 2714 { 2715 int i; 2716 int rv; 2717 unsigned long timeout, timetaken; 2718 2719 dd->mmio = pcim_iomap_table(dd->pdev)[MTIP_ABAR]; 2720 2721 mtip_detect_product(dd); 2722 if (dd->product_type == MTIP_PRODUCT_UNKNOWN) { 2723 rv = -EIO; 2724 goto out1; 2725 } 2726 2727 hba_setup(dd); 2728 2729 dd->port = kzalloc_node(sizeof(struct mtip_port), GFP_KERNEL, 2730 dd->numa_node); 2731 if (!dd->port) 2732 return -ENOMEM; 2733 2734 /* Continue workqueue setup */ 2735 for (i = 0; i < MTIP_MAX_SLOT_GROUPS; i++) 2736 dd->work[i].port = dd->port; 2737 2738 /* Enable unaligned IO constraints for some devices */ 2739 if (mtip_device_unaligned_constrained(dd)) 2740 dd->unal_qdepth = MTIP_MAX_UNALIGNED_SLOTS; 2741 else 2742 dd->unal_qdepth = 0; 2743 2744 atomic_set(&dd->port->cmd_slot_unal, dd->unal_qdepth); 2745 2746 /* Spinlock to prevent concurrent issue */ 2747 for (i = 0; i < MTIP_MAX_SLOT_GROUPS; i++) 2748 spin_lock_init(&dd->port->cmd_issue_lock[i]); 2749 2750 /* Set the port mmio base address. */ 2751 dd->port->mmio = dd->mmio + PORT_OFFSET; 2752 dd->port->dd = dd; 2753 2754 /* DMA allocations */ 2755 rv = mtip_dma_alloc(dd); 2756 if (rv < 0) 2757 goto out1; 2758 2759 /* Setup the pointers to the extended s_active and CI registers. */ 2760 for (i = 0; i < dd->slot_groups; i++) { 2761 dd->port->s_active[i] = 2762 dd->port->mmio + i*0x80 + PORT_SCR_ACT; 2763 dd->port->cmd_issue[i] = 2764 dd->port->mmio + i*0x80 + PORT_COMMAND_ISSUE; 2765 dd->port->completed[i] = 2766 dd->port->mmio + i*0x80 + PORT_SDBV; 2767 } 2768 2769 timetaken = jiffies; 2770 timeout = jiffies + msecs_to_jiffies(30000); 2771 while (((readl(dd->port->mmio + PORT_SCR_STAT) & 0x0F) != 0x03) && 2772 time_before(jiffies, timeout)) { 2773 mdelay(100); 2774 } 2775 if (unlikely(mtip_check_surprise_removal(dd))) { 2776 timetaken = jiffies - timetaken; 2777 dev_warn(&dd->pdev->dev, 2778 "Surprise removal detected at %u ms\n", 2779 jiffies_to_msecs(timetaken)); 2780 rv = -ENODEV; 2781 goto out2 ; 2782 } 2783 if (unlikely(test_bit(MTIP_DDF_REMOVE_PENDING_BIT, &dd->dd_flag))) { 2784 timetaken = jiffies - timetaken; 2785 dev_warn(&dd->pdev->dev, 2786 "Removal detected at %u ms\n", 2787 jiffies_to_msecs(timetaken)); 2788 rv = -EFAULT; 2789 goto out2; 2790 } 2791 2792 /* Conditionally reset the HBA. */ 2793 if (!(readl(dd->mmio + HOST_CAP) & HOST_CAP_NZDMA)) { 2794 if (mtip_hba_reset(dd) < 0) { 2795 dev_err(&dd->pdev->dev, 2796 "Card did not reset within timeout\n"); 2797 rv = -EIO; 2798 goto out2; 2799 } 2800 } else { 2801 /* Clear any pending interrupts on the HBA */ 2802 writel(readl(dd->mmio + HOST_IRQ_STAT), 2803 dd->mmio + HOST_IRQ_STAT); 2804 } 2805 2806 mtip_init_port(dd->port); 2807 mtip_start_port(dd->port); 2808 2809 /* Setup the ISR and enable interrupts. */ 2810 rv = request_irq(dd->pdev->irq, mtip_irq_handler, IRQF_SHARED, 2811 dev_driver_string(&dd->pdev->dev), dd); 2812 if (rv) { 2813 dev_err(&dd->pdev->dev, 2814 "Unable to allocate IRQ %d\n", dd->pdev->irq); 2815 goto out2; 2816 } 2817 irq_set_affinity_hint(dd->pdev->irq, get_cpu_mask(dd->isr_binding)); 2818 2819 /* Enable interrupts on the HBA. */ 2820 writel(readl(dd->mmio + HOST_CTL) | HOST_IRQ_EN, 2821 dd->mmio + HOST_CTL); 2822 2823 init_waitqueue_head(&dd->port->svc_wait); 2824 2825 if (test_bit(MTIP_DDF_REMOVE_PENDING_BIT, &dd->dd_flag)) { 2826 rv = -EFAULT; 2827 goto out3; 2828 } 2829 2830 return rv; 2831 2832 out3: 2833 /* Disable interrupts on the HBA. */ 2834 writel(readl(dd->mmio + HOST_CTL) & ~HOST_IRQ_EN, 2835 dd->mmio + HOST_CTL); 2836 2837 /* Release the IRQ. */ 2838 irq_set_affinity_hint(dd->pdev->irq, NULL); 2839 free_irq(dd->pdev->irq, dd); 2840 2841 out2: 2842 mtip_deinit_port(dd->port); 2843 mtip_dma_free(dd); 2844 2845 out1: 2846 /* Free the memory allocated for the for structure. */ 2847 kfree(dd->port); 2848 2849 return rv; 2850 } 2851 2852 static int mtip_standby_drive(struct driver_data *dd) 2853 { 2854 int rv = 0; 2855 2856 if (dd->sr || !dd->port) 2857 return -ENODEV; 2858 /* 2859 * Send standby immediate (E0h) to the drive so that it 2860 * saves its state. 2861 */ 2862 if (!test_bit(MTIP_PF_REBUILD_BIT, &dd->port->flags) && 2863 !test_bit(MTIP_DDF_REBUILD_FAILED_BIT, &dd->dd_flag) && 2864 !test_bit(MTIP_DDF_SEC_LOCK_BIT, &dd->dd_flag)) { 2865 rv = mtip_standby_immediate(dd->port); 2866 if (rv) 2867 dev_warn(&dd->pdev->dev, 2868 "STANDBY IMMEDIATE failed\n"); 2869 } 2870 return rv; 2871 } 2872 2873 /* 2874 * Called to deinitialize an interface. 2875 * 2876 * @dd Pointer to the driver data structure. 2877 * 2878 * return value 2879 * 0 2880 */ 2881 static int mtip_hw_exit(struct driver_data *dd) 2882 { 2883 if (!dd->sr) { 2884 /* de-initialize the port. */ 2885 mtip_deinit_port(dd->port); 2886 2887 /* Disable interrupts on the HBA. */ 2888 writel(readl(dd->mmio + HOST_CTL) & ~HOST_IRQ_EN, 2889 dd->mmio + HOST_CTL); 2890 } 2891 2892 /* Release the IRQ. */ 2893 irq_set_affinity_hint(dd->pdev->irq, NULL); 2894 free_irq(dd->pdev->irq, dd); 2895 msleep(1000); 2896 2897 /* Free dma regions */ 2898 mtip_dma_free(dd); 2899 2900 /* Free the memory allocated for the for structure. */ 2901 kfree(dd->port); 2902 dd->port = NULL; 2903 2904 return 0; 2905 } 2906 2907 /* 2908 * Issue a Standby Immediate command to the device. 2909 * 2910 * This function is called by the Block Layer just before the 2911 * system powers off during a shutdown. 2912 * 2913 * @dd Pointer to the driver data structure. 2914 * 2915 * return value 2916 * 0 2917 */ 2918 static int mtip_hw_shutdown(struct driver_data *dd) 2919 { 2920 /* 2921 * Send standby immediate (E0h) to the drive so that it 2922 * saves its state. 2923 */ 2924 mtip_standby_drive(dd); 2925 2926 return 0; 2927 } 2928 2929 /* 2930 * Suspend function 2931 * 2932 * This function is called by the Block Layer just before the 2933 * system hibernates. 2934 * 2935 * @dd Pointer to the driver data structure. 2936 * 2937 * return value 2938 * 0 Suspend was successful 2939 * -EFAULT Suspend was not successful 2940 */ 2941 static int mtip_hw_suspend(struct driver_data *dd) 2942 { 2943 /* 2944 * Send standby immediate (E0h) to the drive 2945 * so that it saves its state. 2946 */ 2947 if (mtip_standby_drive(dd) != 0) { 2948 dev_err(&dd->pdev->dev, 2949 "Failed standby-immediate command\n"); 2950 return -EFAULT; 2951 } 2952 2953 /* Disable interrupts on the HBA.*/ 2954 writel(readl(dd->mmio + HOST_CTL) & ~HOST_IRQ_EN, 2955 dd->mmio + HOST_CTL); 2956 mtip_deinit_port(dd->port); 2957 2958 return 0; 2959 } 2960 2961 /* 2962 * Resume function 2963 * 2964 * This function is called by the Block Layer as the 2965 * system resumes. 2966 * 2967 * @dd Pointer to the driver data structure. 2968 * 2969 * return value 2970 * 0 Resume was successful 2971 * -EFAULT Resume was not successful 2972 */ 2973 static int mtip_hw_resume(struct driver_data *dd) 2974 { 2975 /* Perform any needed hardware setup steps */ 2976 hba_setup(dd); 2977 2978 /* Reset the HBA */ 2979 if (mtip_hba_reset(dd) != 0) { 2980 dev_err(&dd->pdev->dev, 2981 "Unable to reset the HBA\n"); 2982 return -EFAULT; 2983 } 2984 2985 /* 2986 * Enable the port, DMA engine, and FIS reception specific 2987 * h/w in controller. 2988 */ 2989 mtip_init_port(dd->port); 2990 mtip_start_port(dd->port); 2991 2992 /* Enable interrupts on the HBA.*/ 2993 writel(readl(dd->mmio + HOST_CTL) | HOST_IRQ_EN, 2994 dd->mmio + HOST_CTL); 2995 2996 return 0; 2997 } 2998 2999 /* 3000 * Helper function for reusing disk name 3001 * upon hot insertion. 3002 */ 3003 static int rssd_disk_name_format(char *prefix, 3004 int index, 3005 char *buf, 3006 int buflen) 3007 { 3008 const int base = 'z' - 'a' + 1; 3009 char *begin = buf + strlen(prefix); 3010 char *end = buf + buflen; 3011 char *p; 3012 int unit; 3013 3014 p = end - 1; 3015 *p = '\0'; 3016 unit = base; 3017 do { 3018 if (p == begin) 3019 return -EINVAL; 3020 *--p = 'a' + (index % unit); 3021 index = (index / unit) - 1; 3022 } while (index >= 0); 3023 3024 memmove(begin, p, end - p); 3025 memcpy(buf, prefix, strlen(prefix)); 3026 3027 return 0; 3028 } 3029 3030 /* 3031 * Block layer IOCTL handler. 3032 * 3033 * @dev Pointer to the block_device structure. 3034 * @mode ignored 3035 * @cmd IOCTL command passed from the user application. 3036 * @arg Argument passed from the user application. 3037 * 3038 * return value 3039 * 0 IOCTL completed successfully. 3040 * -ENOTTY IOCTL not supported or invalid driver data 3041 * structure pointer. 3042 */ 3043 static int mtip_block_ioctl(struct block_device *dev, 3044 blk_mode_t mode, 3045 unsigned cmd, 3046 unsigned long arg) 3047 { 3048 struct driver_data *dd = dev->bd_disk->private_data; 3049 3050 if (!capable(CAP_SYS_ADMIN)) 3051 return -EACCES; 3052 3053 if (!dd) 3054 return -ENOTTY; 3055 3056 if (unlikely(test_bit(MTIP_DDF_REMOVE_PENDING_BIT, &dd->dd_flag))) 3057 return -ENOTTY; 3058 3059 switch (cmd) { 3060 case BLKFLSBUF: 3061 return -ENOTTY; 3062 default: 3063 return mtip_hw_ioctl(dd, cmd, arg); 3064 } 3065 } 3066 3067 #ifdef CONFIG_COMPAT 3068 /* 3069 * Block layer compat IOCTL handler. 3070 * 3071 * @dev Pointer to the block_device structure. 3072 * @mode ignored 3073 * @cmd IOCTL command passed from the user application. 3074 * @arg Argument passed from the user application. 3075 * 3076 * return value 3077 * 0 IOCTL completed successfully. 3078 * -ENOTTY IOCTL not supported or invalid driver data 3079 * structure pointer. 3080 */ 3081 static int mtip_block_compat_ioctl(struct block_device *dev, 3082 blk_mode_t mode, 3083 unsigned cmd, 3084 unsigned long arg) 3085 { 3086 struct driver_data *dd = dev->bd_disk->private_data; 3087 3088 if (!capable(CAP_SYS_ADMIN)) 3089 return -EACCES; 3090 3091 if (!dd) 3092 return -ENOTTY; 3093 3094 if (unlikely(test_bit(MTIP_DDF_REMOVE_PENDING_BIT, &dd->dd_flag))) 3095 return -ENOTTY; 3096 3097 switch (cmd) { 3098 case BLKFLSBUF: 3099 return -ENOTTY; 3100 case HDIO_DRIVE_TASKFILE: { 3101 struct mtip_compat_ide_task_request_s __user *compat_req_task; 3102 ide_task_request_t req_task; 3103 int compat_tasksize, outtotal, ret; 3104 3105 compat_tasksize = 3106 sizeof(struct mtip_compat_ide_task_request_s); 3107 3108 compat_req_task = 3109 (struct mtip_compat_ide_task_request_s __user *) arg; 3110 3111 if (copy_from_user(&req_task, (void __user *) arg, 3112 compat_tasksize - (2 * sizeof(compat_long_t)))) 3113 return -EFAULT; 3114 3115 if (get_user(req_task.out_size, &compat_req_task->out_size)) 3116 return -EFAULT; 3117 3118 if (get_user(req_task.in_size, &compat_req_task->in_size)) 3119 return -EFAULT; 3120 3121 outtotal = sizeof(struct mtip_compat_ide_task_request_s); 3122 3123 ret = exec_drive_taskfile(dd, (void __user *) arg, 3124 &req_task, outtotal); 3125 3126 if (copy_to_user((void __user *) arg, &req_task, 3127 compat_tasksize - 3128 (2 * sizeof(compat_long_t)))) 3129 return -EFAULT; 3130 3131 if (put_user(req_task.out_size, &compat_req_task->out_size)) 3132 return -EFAULT; 3133 3134 if (put_user(req_task.in_size, &compat_req_task->in_size)) 3135 return -EFAULT; 3136 3137 return ret; 3138 } 3139 default: 3140 return mtip_hw_ioctl(dd, cmd, arg); 3141 } 3142 } 3143 #endif 3144 3145 /* 3146 * Obtain the geometry of the device. 3147 * 3148 * You may think that this function is obsolete, but some applications, 3149 * fdisk for example still used CHS values. This function describes the 3150 * device as having 224 heads and 56 sectors per cylinder. These values are 3151 * chosen so that each cylinder is aligned on a 4KB boundary. Since a 3152 * partition is described in terms of a start and end cylinder this means 3153 * that each partition is also 4KB aligned. Non-aligned partitions adversely 3154 * affects performance. 3155 * 3156 * @dev Pointer to the block_device strucutre. 3157 * @geo Pointer to a hd_geometry structure. 3158 * 3159 * return value 3160 * 0 Operation completed successfully. 3161 * -ENOTTY An error occurred while reading the drive capacity. 3162 */ 3163 static int mtip_block_getgeo(struct block_device *dev, 3164 struct hd_geometry *geo) 3165 { 3166 struct driver_data *dd = dev->bd_disk->private_data; 3167 sector_t capacity; 3168 3169 if (!dd) 3170 return -ENOTTY; 3171 3172 if (!(mtip_hw_get_capacity(dd, &capacity))) { 3173 dev_warn(&dd->pdev->dev, 3174 "Could not get drive capacity.\n"); 3175 return -ENOTTY; 3176 } 3177 3178 geo->heads = 224; 3179 geo->sectors = 56; 3180 sector_div(capacity, (geo->heads * geo->sectors)); 3181 geo->cylinders = capacity; 3182 return 0; 3183 } 3184 3185 static void mtip_block_free_disk(struct gendisk *disk) 3186 { 3187 struct driver_data *dd = disk->private_data; 3188 3189 ida_free(&rssd_index_ida, dd->index); 3190 kfree(dd); 3191 } 3192 3193 /* 3194 * Block device operation function. 3195 * 3196 * This structure contains pointers to the functions required by the block 3197 * layer. 3198 */ 3199 static const struct block_device_operations mtip_block_ops = { 3200 .ioctl = mtip_block_ioctl, 3201 #ifdef CONFIG_COMPAT 3202 .compat_ioctl = mtip_block_compat_ioctl, 3203 #endif 3204 .getgeo = mtip_block_getgeo, 3205 .free_disk = mtip_block_free_disk, 3206 .owner = THIS_MODULE 3207 }; 3208 3209 static inline bool is_se_active(struct driver_data *dd) 3210 { 3211 if (unlikely(test_bit(MTIP_PF_SE_ACTIVE_BIT, &dd->port->flags))) { 3212 if (dd->port->ic_pause_timer) { 3213 unsigned long to = dd->port->ic_pause_timer + 3214 msecs_to_jiffies(1000); 3215 if (time_after(jiffies, to)) { 3216 clear_bit(MTIP_PF_SE_ACTIVE_BIT, 3217 &dd->port->flags); 3218 clear_bit(MTIP_DDF_SEC_LOCK_BIT, &dd->dd_flag); 3219 dd->port->ic_pause_timer = 0; 3220 wake_up_interruptible(&dd->port->svc_wait); 3221 return false; 3222 } 3223 } 3224 return true; 3225 } 3226 return false; 3227 } 3228 3229 static inline bool is_stopped(struct driver_data *dd, struct request *rq) 3230 { 3231 if (likely(!(dd->dd_flag & MTIP_DDF_STOP_IO))) 3232 return false; 3233 3234 if (test_bit(MTIP_DDF_REMOVE_PENDING_BIT, &dd->dd_flag)) 3235 return true; 3236 if (test_bit(MTIP_DDF_OVER_TEMP_BIT, &dd->dd_flag)) 3237 return true; 3238 if (test_bit(MTIP_DDF_WRITE_PROTECT_BIT, &dd->dd_flag) && 3239 rq_data_dir(rq)) 3240 return true; 3241 if (test_bit(MTIP_DDF_SEC_LOCK_BIT, &dd->dd_flag)) 3242 return true; 3243 if (test_bit(MTIP_DDF_REBUILD_FAILED_BIT, &dd->dd_flag)) 3244 return true; 3245 3246 return false; 3247 } 3248 3249 static bool mtip_check_unal_depth(struct blk_mq_hw_ctx *hctx, 3250 struct request *rq) 3251 { 3252 struct driver_data *dd = hctx->queue->queuedata; 3253 struct mtip_cmd *cmd = blk_mq_rq_to_pdu(rq); 3254 3255 if (rq_data_dir(rq) == READ || !dd->unal_qdepth) 3256 return false; 3257 3258 /* 3259 * If unaligned depth must be limited on this controller, mark it 3260 * as unaligned if the IO isn't on a 4k boundary (start of length). 3261 */ 3262 if (blk_rq_sectors(rq) <= 64) { 3263 if ((blk_rq_pos(rq) & 7) || (blk_rq_sectors(rq) & 7)) 3264 cmd->unaligned = 1; 3265 } 3266 3267 if (cmd->unaligned && atomic_dec_if_positive(&dd->port->cmd_slot_unal) >= 0) 3268 return true; 3269 3270 return false; 3271 } 3272 3273 static blk_status_t mtip_issue_reserved_cmd(struct blk_mq_hw_ctx *hctx, 3274 struct request *rq) 3275 { 3276 struct driver_data *dd = hctx->queue->queuedata; 3277 struct mtip_cmd *cmd = blk_mq_rq_to_pdu(rq); 3278 struct mtip_int_cmd *icmd = cmd->icmd; 3279 struct mtip_cmd_hdr *hdr = 3280 dd->port->command_list + sizeof(struct mtip_cmd_hdr) * rq->tag; 3281 struct mtip_cmd_sg *command_sg; 3282 3283 if (mtip_commands_active(dd->port)) 3284 return BLK_STS_DEV_RESOURCE; 3285 3286 hdr->ctba = cpu_to_le32(cmd->command_dma & 0xFFFFFFFF); 3287 if (test_bit(MTIP_PF_HOST_CAP_64, &dd->port->flags)) 3288 hdr->ctbau = cpu_to_le32((cmd->command_dma >> 16) >> 16); 3289 /* Populate the SG list */ 3290 hdr->opts = cpu_to_le32(icmd->opts | icmd->fis_len); 3291 if (icmd->buf_len) { 3292 command_sg = cmd->command + AHCI_CMD_TBL_HDR_SZ; 3293 3294 command_sg->info = cpu_to_le32((icmd->buf_len-1) & 0x3FFFFF); 3295 command_sg->dba = cpu_to_le32(icmd->buffer & 0xFFFFFFFF); 3296 command_sg->dba_upper = 3297 cpu_to_le32((icmd->buffer >> 16) >> 16); 3298 3299 hdr->opts |= cpu_to_le32((1 << 16)); 3300 } 3301 3302 /* Populate the command header */ 3303 hdr->byte_count = 0; 3304 3305 blk_mq_start_request(rq); 3306 mtip_issue_non_ncq_command(dd->port, rq->tag); 3307 return 0; 3308 } 3309 3310 static blk_status_t mtip_queue_rq(struct blk_mq_hw_ctx *hctx, 3311 const struct blk_mq_queue_data *bd) 3312 { 3313 struct driver_data *dd = hctx->queue->queuedata; 3314 struct request *rq = bd->rq; 3315 struct mtip_cmd *cmd = blk_mq_rq_to_pdu(rq); 3316 3317 if (blk_rq_is_passthrough(rq)) 3318 return mtip_issue_reserved_cmd(hctx, rq); 3319 3320 if (unlikely(mtip_check_unal_depth(hctx, rq))) 3321 return BLK_STS_DEV_RESOURCE; 3322 3323 if (is_se_active(dd) || is_stopped(dd, rq)) 3324 return BLK_STS_IOERR; 3325 3326 blk_mq_start_request(rq); 3327 3328 mtip_hw_submit_io(dd, rq, cmd, hctx); 3329 return BLK_STS_OK; 3330 } 3331 3332 static void mtip_free_cmd(struct blk_mq_tag_set *set, struct request *rq, 3333 unsigned int hctx_idx) 3334 { 3335 struct driver_data *dd = set->driver_data; 3336 struct mtip_cmd *cmd = blk_mq_rq_to_pdu(rq); 3337 3338 if (!cmd->command) 3339 return; 3340 3341 dma_free_coherent(&dd->pdev->dev, CMD_DMA_ALLOC_SZ, cmd->command, 3342 cmd->command_dma); 3343 } 3344 3345 static int mtip_init_cmd(struct blk_mq_tag_set *set, struct request *rq, 3346 unsigned int hctx_idx, unsigned int numa_node) 3347 { 3348 struct driver_data *dd = set->driver_data; 3349 struct mtip_cmd *cmd = blk_mq_rq_to_pdu(rq); 3350 3351 cmd->command = dma_alloc_coherent(&dd->pdev->dev, CMD_DMA_ALLOC_SZ, 3352 &cmd->command_dma, GFP_KERNEL); 3353 if (!cmd->command) 3354 return -ENOMEM; 3355 3356 sg_init_table(cmd->sg, MTIP_MAX_SG); 3357 return 0; 3358 } 3359 3360 static enum blk_eh_timer_return mtip_cmd_timeout(struct request *req) 3361 { 3362 struct driver_data *dd = req->q->queuedata; 3363 3364 if (blk_mq_is_reserved_rq(req)) { 3365 struct mtip_cmd *cmd = blk_mq_rq_to_pdu(req); 3366 3367 cmd->status = BLK_STS_TIMEOUT; 3368 blk_mq_complete_request(req); 3369 return BLK_EH_DONE; 3370 } 3371 3372 if (test_bit(req->tag, dd->port->cmds_to_issue)) 3373 goto exit_handler; 3374 3375 if (test_and_set_bit(MTIP_PF_TO_ACTIVE_BIT, &dd->port->flags)) 3376 goto exit_handler; 3377 3378 wake_up_interruptible(&dd->port->svc_wait); 3379 exit_handler: 3380 return BLK_EH_RESET_TIMER; 3381 } 3382 3383 static const struct blk_mq_ops mtip_mq_ops = { 3384 .queue_rq = mtip_queue_rq, 3385 .init_request = mtip_init_cmd, 3386 .exit_request = mtip_free_cmd, 3387 .complete = mtip_softirq_done_fn, 3388 .timeout = mtip_cmd_timeout, 3389 }; 3390 3391 /* 3392 * Block layer initialization function. 3393 * 3394 * This function is called once by the PCI layer for each P320 3395 * device that is connected to the system. 3396 * 3397 * @dd Pointer to the driver data structure. 3398 * 3399 * return value 3400 * 0 on success else an error code. 3401 */ 3402 static int mtip_block_initialize(struct driver_data *dd) 3403 { 3404 int rv = 0, wait_for_rebuild = 0; 3405 sector_t capacity; 3406 unsigned int index = 0; 3407 3408 if (dd->disk) 3409 goto skip_create_disk; /* hw init done, before rebuild */ 3410 3411 if (mtip_hw_init(dd)) { 3412 rv = -EINVAL; 3413 goto protocol_init_error; 3414 } 3415 3416 memset(&dd->tags, 0, sizeof(dd->tags)); 3417 dd->tags.ops = &mtip_mq_ops; 3418 dd->tags.nr_hw_queues = 1; 3419 dd->tags.queue_depth = MTIP_MAX_COMMAND_SLOTS; 3420 dd->tags.reserved_tags = 1; 3421 dd->tags.cmd_size = sizeof(struct mtip_cmd); 3422 dd->tags.numa_node = dd->numa_node; 3423 dd->tags.flags = BLK_MQ_F_SHOULD_MERGE; 3424 dd->tags.driver_data = dd; 3425 dd->tags.timeout = MTIP_NCQ_CMD_TIMEOUT_MS; 3426 3427 rv = blk_mq_alloc_tag_set(&dd->tags); 3428 if (rv) { 3429 dev_err(&dd->pdev->dev, 3430 "Unable to allocate request queue\n"); 3431 goto block_queue_alloc_tag_error; 3432 } 3433 3434 dd->disk = blk_mq_alloc_disk(&dd->tags, dd); 3435 if (IS_ERR(dd->disk)) { 3436 dev_err(&dd->pdev->dev, 3437 "Unable to allocate request queue\n"); 3438 rv = -ENOMEM; 3439 goto block_queue_alloc_init_error; 3440 } 3441 dd->queue = dd->disk->queue; 3442 3443 rv = ida_alloc(&rssd_index_ida, GFP_KERNEL); 3444 if (rv < 0) 3445 goto ida_get_error; 3446 index = rv; 3447 3448 rv = rssd_disk_name_format("rssd", 3449 index, 3450 dd->disk->disk_name, 3451 DISK_NAME_LEN); 3452 if (rv) 3453 goto disk_index_error; 3454 3455 dd->disk->major = dd->major; 3456 dd->disk->first_minor = index * MTIP_MAX_MINORS; 3457 dd->disk->minors = MTIP_MAX_MINORS; 3458 dd->disk->fops = &mtip_block_ops; 3459 dd->disk->private_data = dd; 3460 dd->index = index; 3461 3462 mtip_hw_debugfs_init(dd); 3463 3464 skip_create_disk: 3465 /* Initialize the protocol layer. */ 3466 wait_for_rebuild = mtip_hw_get_identify(dd); 3467 if (wait_for_rebuild < 0) { 3468 dev_err(&dd->pdev->dev, 3469 "Protocol layer initialization failed\n"); 3470 rv = -EINVAL; 3471 goto init_hw_cmds_error; 3472 } 3473 3474 /* 3475 * if rebuild pending, start the service thread, and delay the block 3476 * queue creation and device_add_disk() 3477 */ 3478 if (wait_for_rebuild == MTIP_FTL_REBUILD_MAGIC) 3479 goto start_service_thread; 3480 3481 /* Set device limits. */ 3482 blk_queue_flag_set(QUEUE_FLAG_NONROT, dd->queue); 3483 blk_queue_flag_clear(QUEUE_FLAG_ADD_RANDOM, dd->queue); 3484 blk_queue_max_segments(dd->queue, MTIP_MAX_SG); 3485 blk_queue_physical_block_size(dd->queue, 4096); 3486 blk_queue_max_hw_sectors(dd->queue, 0xffff); 3487 blk_queue_max_segment_size(dd->queue, 0x400000); 3488 dma_set_max_seg_size(&dd->pdev->dev, 0x400000); 3489 blk_queue_io_min(dd->queue, 4096); 3490 3491 /* Set the capacity of the device in 512 byte sectors. */ 3492 if (!(mtip_hw_get_capacity(dd, &capacity))) { 3493 dev_warn(&dd->pdev->dev, 3494 "Could not read drive capacity\n"); 3495 rv = -EIO; 3496 goto read_capacity_error; 3497 } 3498 set_capacity(dd->disk, capacity); 3499 3500 /* Enable the block device and add it to /dev */ 3501 rv = device_add_disk(&dd->pdev->dev, dd->disk, mtip_disk_attr_groups); 3502 if (rv) 3503 goto read_capacity_error; 3504 3505 if (dd->mtip_svc_handler) { 3506 set_bit(MTIP_DDF_INIT_DONE_BIT, &dd->dd_flag); 3507 return rv; /* service thread created for handling rebuild */ 3508 } 3509 3510 start_service_thread: 3511 dd->mtip_svc_handler = kthread_create_on_node(mtip_service_thread, 3512 dd, dd->numa_node, 3513 "mtip_svc_thd_%02d", index); 3514 3515 if (IS_ERR(dd->mtip_svc_handler)) { 3516 dev_err(&dd->pdev->dev, "service thread failed to start\n"); 3517 dd->mtip_svc_handler = NULL; 3518 rv = -EFAULT; 3519 goto kthread_run_error; 3520 } 3521 wake_up_process(dd->mtip_svc_handler); 3522 if (wait_for_rebuild == MTIP_FTL_REBUILD_MAGIC) 3523 rv = wait_for_rebuild; 3524 3525 return rv; 3526 3527 kthread_run_error: 3528 /* Delete our gendisk. This also removes the device from /dev */ 3529 del_gendisk(dd->disk); 3530 read_capacity_error: 3531 init_hw_cmds_error: 3532 mtip_hw_debugfs_exit(dd); 3533 disk_index_error: 3534 ida_free(&rssd_index_ida, index); 3535 ida_get_error: 3536 put_disk(dd->disk); 3537 block_queue_alloc_init_error: 3538 blk_mq_free_tag_set(&dd->tags); 3539 block_queue_alloc_tag_error: 3540 mtip_hw_exit(dd); /* De-initialize the protocol layer. */ 3541 protocol_init_error: 3542 return rv; 3543 } 3544 3545 /* 3546 * Function called by the PCI layer when just before the 3547 * machine shuts down. 3548 * 3549 * If a protocol layer shutdown function is present it will be called 3550 * by this function. 3551 * 3552 * @dd Pointer to the driver data structure. 3553 * 3554 * return value 3555 * 0 3556 */ 3557 static int mtip_block_shutdown(struct driver_data *dd) 3558 { 3559 mtip_hw_shutdown(dd); 3560 3561 dev_info(&dd->pdev->dev, 3562 "Shutting down %s ...\n", dd->disk->disk_name); 3563 3564 if (test_bit(MTIP_DDF_INIT_DONE_BIT, &dd->dd_flag)) 3565 del_gendisk(dd->disk); 3566 3567 blk_mq_free_tag_set(&dd->tags); 3568 put_disk(dd->disk); 3569 return 0; 3570 } 3571 3572 static int mtip_block_suspend(struct driver_data *dd) 3573 { 3574 dev_info(&dd->pdev->dev, 3575 "Suspending %s ...\n", dd->disk->disk_name); 3576 mtip_hw_suspend(dd); 3577 return 0; 3578 } 3579 3580 static int mtip_block_resume(struct driver_data *dd) 3581 { 3582 dev_info(&dd->pdev->dev, "Resuming %s ...\n", 3583 dd->disk->disk_name); 3584 mtip_hw_resume(dd); 3585 return 0; 3586 } 3587 3588 static void drop_cpu(int cpu) 3589 { 3590 cpu_use[cpu]--; 3591 } 3592 3593 static int get_least_used_cpu_on_node(int node) 3594 { 3595 int cpu, least_used_cpu, least_cnt; 3596 const struct cpumask *node_mask; 3597 3598 node_mask = cpumask_of_node(node); 3599 least_used_cpu = cpumask_first(node_mask); 3600 least_cnt = cpu_use[least_used_cpu]; 3601 cpu = least_used_cpu; 3602 3603 for_each_cpu(cpu, node_mask) { 3604 if (cpu_use[cpu] < least_cnt) { 3605 least_used_cpu = cpu; 3606 least_cnt = cpu_use[cpu]; 3607 } 3608 } 3609 cpu_use[least_used_cpu]++; 3610 return least_used_cpu; 3611 } 3612 3613 /* Helper for selecting a node in round robin mode */ 3614 static inline int mtip_get_next_rr_node(void) 3615 { 3616 static int next_node = NUMA_NO_NODE; 3617 3618 if (next_node == NUMA_NO_NODE) { 3619 next_node = first_online_node; 3620 return next_node; 3621 } 3622 3623 next_node = next_online_node(next_node); 3624 if (next_node == MAX_NUMNODES) 3625 next_node = first_online_node; 3626 return next_node; 3627 } 3628 3629 static DEFINE_HANDLER(0); 3630 static DEFINE_HANDLER(1); 3631 static DEFINE_HANDLER(2); 3632 static DEFINE_HANDLER(3); 3633 static DEFINE_HANDLER(4); 3634 static DEFINE_HANDLER(5); 3635 static DEFINE_HANDLER(6); 3636 static DEFINE_HANDLER(7); 3637 3638 static void mtip_disable_link_opts(struct driver_data *dd, struct pci_dev *pdev) 3639 { 3640 unsigned short pcie_dev_ctrl; 3641 3642 if (pci_is_pcie(pdev)) { 3643 pcie_capability_read_word(pdev, PCI_EXP_DEVCTL, &pcie_dev_ctrl); 3644 if (pcie_dev_ctrl & PCI_EXP_DEVCTL_NOSNOOP_EN || 3645 pcie_dev_ctrl & PCI_EXP_DEVCTL_RELAX_EN) { 3646 dev_info(&dd->pdev->dev, 3647 "Disabling ERO/No-Snoop on bridge device %04x:%04x\n", 3648 pdev->vendor, pdev->device); 3649 pcie_dev_ctrl &= ~(PCI_EXP_DEVCTL_NOSNOOP_EN | 3650 PCI_EXP_DEVCTL_RELAX_EN); 3651 pcie_capability_write_word(pdev, PCI_EXP_DEVCTL, 3652 pcie_dev_ctrl); 3653 } 3654 } 3655 } 3656 3657 static void mtip_fix_ero_nosnoop(struct driver_data *dd, struct pci_dev *pdev) 3658 { 3659 /* 3660 * This workaround is specific to AMD/ATI chipset with a PCI upstream 3661 * device with device id 0x5aXX 3662 */ 3663 if (pdev->bus && pdev->bus->self) { 3664 if (pdev->bus->self->vendor == PCI_VENDOR_ID_ATI && 3665 ((pdev->bus->self->device & 0xff00) == 0x5a00)) { 3666 mtip_disable_link_opts(dd, pdev->bus->self); 3667 } else { 3668 /* Check further up the topology */ 3669 struct pci_dev *parent_dev = pdev->bus->self; 3670 if (parent_dev->bus && 3671 parent_dev->bus->parent && 3672 parent_dev->bus->parent->self && 3673 parent_dev->bus->parent->self->vendor == 3674 PCI_VENDOR_ID_ATI && 3675 (parent_dev->bus->parent->self->device & 3676 0xff00) == 0x5a00) { 3677 mtip_disable_link_opts(dd, 3678 parent_dev->bus->parent->self); 3679 } 3680 } 3681 } 3682 } 3683 3684 /* 3685 * Called for each supported PCI device detected. 3686 * 3687 * This function allocates the private data structure, enables the 3688 * PCI device and then calls the block layer initialization function. 3689 * 3690 * return value 3691 * 0 on success else an error code. 3692 */ 3693 static int mtip_pci_probe(struct pci_dev *pdev, 3694 const struct pci_device_id *ent) 3695 { 3696 int rv = 0; 3697 struct driver_data *dd = NULL; 3698 char cpu_list[256]; 3699 const struct cpumask *node_mask; 3700 int cpu, i = 0, j = 0; 3701 int my_node = NUMA_NO_NODE; 3702 3703 /* Allocate memory for this devices private data. */ 3704 my_node = pcibus_to_node(pdev->bus); 3705 if (my_node != NUMA_NO_NODE) { 3706 if (!node_online(my_node)) 3707 my_node = mtip_get_next_rr_node(); 3708 } else { 3709 dev_info(&pdev->dev, "Kernel not reporting proximity, choosing a node\n"); 3710 my_node = mtip_get_next_rr_node(); 3711 } 3712 dev_info(&pdev->dev, "NUMA node %d (closest: %d,%d, probe on %d:%d)\n", 3713 my_node, pcibus_to_node(pdev->bus), dev_to_node(&pdev->dev), 3714 cpu_to_node(raw_smp_processor_id()), raw_smp_processor_id()); 3715 3716 dd = kzalloc_node(sizeof(struct driver_data), GFP_KERNEL, my_node); 3717 if (!dd) 3718 return -ENOMEM; 3719 3720 /* Attach the private data to this PCI device. */ 3721 pci_set_drvdata(pdev, dd); 3722 3723 rv = pcim_enable_device(pdev); 3724 if (rv < 0) { 3725 dev_err(&pdev->dev, "Unable to enable device\n"); 3726 goto iomap_err; 3727 } 3728 3729 /* Map BAR5 to memory. */ 3730 rv = pcim_iomap_regions(pdev, 1 << MTIP_ABAR, MTIP_DRV_NAME); 3731 if (rv < 0) { 3732 dev_err(&pdev->dev, "Unable to map regions\n"); 3733 goto iomap_err; 3734 } 3735 3736 rv = dma_set_mask_and_coherent(&pdev->dev, DMA_BIT_MASK(64)); 3737 if (rv) { 3738 dev_warn(&pdev->dev, "64-bit DMA enable failed\n"); 3739 goto setmask_err; 3740 } 3741 3742 /* Copy the info we may need later into the private data structure. */ 3743 dd->major = mtip_major; 3744 dd->instance = instance; 3745 dd->pdev = pdev; 3746 dd->numa_node = my_node; 3747 3748 memset(dd->workq_name, 0, 32); 3749 snprintf(dd->workq_name, 31, "mtipq%d", dd->instance); 3750 3751 dd->isr_workq = create_workqueue(dd->workq_name); 3752 if (!dd->isr_workq) { 3753 dev_warn(&pdev->dev, "Can't create wq %d\n", dd->instance); 3754 rv = -ENOMEM; 3755 goto setmask_err; 3756 } 3757 3758 memset(cpu_list, 0, sizeof(cpu_list)); 3759 3760 node_mask = cpumask_of_node(dd->numa_node); 3761 if (!cpumask_empty(node_mask)) { 3762 for_each_cpu(cpu, node_mask) 3763 { 3764 snprintf(&cpu_list[j], 256 - j, "%d ", cpu); 3765 j = strlen(cpu_list); 3766 } 3767 3768 dev_info(&pdev->dev, "Node %d on package %d has %d cpu(s): %s\n", 3769 dd->numa_node, 3770 topology_physical_package_id(cpumask_first(node_mask)), 3771 nr_cpus_node(dd->numa_node), 3772 cpu_list); 3773 } else 3774 dev_dbg(&pdev->dev, "mtip32xx: node_mask empty\n"); 3775 3776 dd->isr_binding = get_least_used_cpu_on_node(dd->numa_node); 3777 dev_info(&pdev->dev, "Initial IRQ binding node:cpu %d:%d\n", 3778 cpu_to_node(dd->isr_binding), dd->isr_binding); 3779 3780 /* first worker context always runs in ISR */ 3781 dd->work[0].cpu_binding = dd->isr_binding; 3782 dd->work[1].cpu_binding = get_least_used_cpu_on_node(dd->numa_node); 3783 dd->work[2].cpu_binding = get_least_used_cpu_on_node(dd->numa_node); 3784 dd->work[3].cpu_binding = dd->work[0].cpu_binding; 3785 dd->work[4].cpu_binding = dd->work[1].cpu_binding; 3786 dd->work[5].cpu_binding = dd->work[2].cpu_binding; 3787 dd->work[6].cpu_binding = dd->work[2].cpu_binding; 3788 dd->work[7].cpu_binding = dd->work[1].cpu_binding; 3789 3790 /* Log the bindings */ 3791 for_each_present_cpu(cpu) { 3792 memset(cpu_list, 0, sizeof(cpu_list)); 3793 for (i = 0, j = 0; i < MTIP_MAX_SLOT_GROUPS; i++) { 3794 if (dd->work[i].cpu_binding == cpu) { 3795 snprintf(&cpu_list[j], 256 - j, "%d ", i); 3796 j = strlen(cpu_list); 3797 } 3798 } 3799 if (j) 3800 dev_info(&pdev->dev, "CPU %d: WQs %s\n", cpu, cpu_list); 3801 } 3802 3803 INIT_WORK(&dd->work[0].work, mtip_workq_sdbf0); 3804 INIT_WORK(&dd->work[1].work, mtip_workq_sdbf1); 3805 INIT_WORK(&dd->work[2].work, mtip_workq_sdbf2); 3806 INIT_WORK(&dd->work[3].work, mtip_workq_sdbf3); 3807 INIT_WORK(&dd->work[4].work, mtip_workq_sdbf4); 3808 INIT_WORK(&dd->work[5].work, mtip_workq_sdbf5); 3809 INIT_WORK(&dd->work[6].work, mtip_workq_sdbf6); 3810 INIT_WORK(&dd->work[7].work, mtip_workq_sdbf7); 3811 3812 pci_set_master(pdev); 3813 rv = pci_enable_msi(pdev); 3814 if (rv) { 3815 dev_warn(&pdev->dev, 3816 "Unable to enable MSI interrupt.\n"); 3817 goto msi_initialize_err; 3818 } 3819 3820 mtip_fix_ero_nosnoop(dd, pdev); 3821 3822 /* Initialize the block layer. */ 3823 rv = mtip_block_initialize(dd); 3824 if (rv < 0) { 3825 dev_err(&pdev->dev, 3826 "Unable to initialize block layer\n"); 3827 goto block_initialize_err; 3828 } 3829 3830 /* 3831 * Increment the instance count so that each device has a unique 3832 * instance number. 3833 */ 3834 instance++; 3835 if (rv != MTIP_FTL_REBUILD_MAGIC) 3836 set_bit(MTIP_DDF_INIT_DONE_BIT, &dd->dd_flag); 3837 else 3838 rv = 0; /* device in rebuild state, return 0 from probe */ 3839 3840 goto done; 3841 3842 block_initialize_err: 3843 pci_disable_msi(pdev); 3844 3845 msi_initialize_err: 3846 if (dd->isr_workq) { 3847 destroy_workqueue(dd->isr_workq); 3848 drop_cpu(dd->work[0].cpu_binding); 3849 drop_cpu(dd->work[1].cpu_binding); 3850 drop_cpu(dd->work[2].cpu_binding); 3851 } 3852 setmask_err: 3853 pcim_iounmap_regions(pdev, 1 << MTIP_ABAR); 3854 3855 iomap_err: 3856 kfree(dd); 3857 pci_set_drvdata(pdev, NULL); 3858 return rv; 3859 done: 3860 return rv; 3861 } 3862 3863 /* 3864 * Called for each probed device when the device is removed or the 3865 * driver is unloaded. 3866 * 3867 * return value 3868 * None 3869 */ 3870 static void mtip_pci_remove(struct pci_dev *pdev) 3871 { 3872 struct driver_data *dd = pci_get_drvdata(pdev); 3873 unsigned long to; 3874 3875 mtip_check_surprise_removal(dd); 3876 synchronize_irq(dd->pdev->irq); 3877 3878 /* Spin until workers are done */ 3879 to = jiffies + msecs_to_jiffies(4000); 3880 do { 3881 msleep(20); 3882 } while (atomic_read(&dd->irq_workers_active) != 0 && 3883 time_before(jiffies, to)); 3884 3885 if (atomic_read(&dd->irq_workers_active) != 0) { 3886 dev_warn(&dd->pdev->dev, 3887 "Completion workers still active!\n"); 3888 } 3889 3890 set_bit(MTIP_DDF_REMOVE_PENDING_BIT, &dd->dd_flag); 3891 3892 if (test_bit(MTIP_DDF_INIT_DONE_BIT, &dd->dd_flag)) 3893 del_gendisk(dd->disk); 3894 3895 mtip_hw_debugfs_exit(dd); 3896 3897 if (dd->mtip_svc_handler) { 3898 set_bit(MTIP_PF_SVC_THD_STOP_BIT, &dd->port->flags); 3899 wake_up_interruptible(&dd->port->svc_wait); 3900 kthread_stop(dd->mtip_svc_handler); 3901 } 3902 3903 if (!dd->sr) { 3904 /* 3905 * Explicitly wait here for IOs to quiesce, 3906 * as mtip_standby_drive usually won't wait for IOs. 3907 */ 3908 if (!mtip_quiesce_io(dd->port, MTIP_QUIESCE_IO_TIMEOUT_MS)) 3909 mtip_standby_drive(dd); 3910 } 3911 else 3912 dev_info(&dd->pdev->dev, "device %s surprise removal\n", 3913 dd->disk->disk_name); 3914 3915 blk_mq_free_tag_set(&dd->tags); 3916 3917 /* De-initialize the protocol layer. */ 3918 mtip_hw_exit(dd); 3919 3920 if (dd->isr_workq) { 3921 destroy_workqueue(dd->isr_workq); 3922 drop_cpu(dd->work[0].cpu_binding); 3923 drop_cpu(dd->work[1].cpu_binding); 3924 drop_cpu(dd->work[2].cpu_binding); 3925 } 3926 3927 pci_disable_msi(pdev); 3928 3929 pcim_iounmap_regions(pdev, 1 << MTIP_ABAR); 3930 pci_set_drvdata(pdev, NULL); 3931 3932 put_disk(dd->disk); 3933 } 3934 3935 /* 3936 * Called for each probed device when the device is suspended. 3937 * 3938 * return value 3939 * 0 Success 3940 * <0 Error 3941 */ 3942 static int __maybe_unused mtip_pci_suspend(struct device *dev) 3943 { 3944 int rv = 0; 3945 struct driver_data *dd = dev_get_drvdata(dev); 3946 3947 set_bit(MTIP_DDF_RESUME_BIT, &dd->dd_flag); 3948 3949 /* Disable ports & interrupts then send standby immediate */ 3950 rv = mtip_block_suspend(dd); 3951 if (rv < 0) 3952 dev_err(dev, "Failed to suspend controller\n"); 3953 3954 return rv; 3955 } 3956 3957 /* 3958 * Called for each probed device when the device is resumed. 3959 * 3960 * return value 3961 * 0 Success 3962 * <0 Error 3963 */ 3964 static int __maybe_unused mtip_pci_resume(struct device *dev) 3965 { 3966 int rv = 0; 3967 struct driver_data *dd = dev_get_drvdata(dev); 3968 3969 /* 3970 * Calls hbaReset, initPort, & startPort function 3971 * then enables interrupts 3972 */ 3973 rv = mtip_block_resume(dd); 3974 if (rv < 0) 3975 dev_err(dev, "Unable to resume\n"); 3976 3977 clear_bit(MTIP_DDF_RESUME_BIT, &dd->dd_flag); 3978 3979 return rv; 3980 } 3981 3982 /* 3983 * Shutdown routine 3984 * 3985 * return value 3986 * None 3987 */ 3988 static void mtip_pci_shutdown(struct pci_dev *pdev) 3989 { 3990 struct driver_data *dd = pci_get_drvdata(pdev); 3991 if (dd) 3992 mtip_block_shutdown(dd); 3993 } 3994 3995 /* Table of device ids supported by this driver. */ 3996 static const struct pci_device_id mtip_pci_tbl[] = { 3997 { PCI_DEVICE(PCI_VENDOR_ID_MICRON, P320H_DEVICE_ID) }, 3998 { PCI_DEVICE(PCI_VENDOR_ID_MICRON, P320M_DEVICE_ID) }, 3999 { PCI_DEVICE(PCI_VENDOR_ID_MICRON, P320S_DEVICE_ID) }, 4000 { PCI_DEVICE(PCI_VENDOR_ID_MICRON, P325M_DEVICE_ID) }, 4001 { PCI_DEVICE(PCI_VENDOR_ID_MICRON, P420H_DEVICE_ID) }, 4002 { PCI_DEVICE(PCI_VENDOR_ID_MICRON, P420M_DEVICE_ID) }, 4003 { PCI_DEVICE(PCI_VENDOR_ID_MICRON, P425M_DEVICE_ID) }, 4004 { 0 } 4005 }; 4006 4007 static SIMPLE_DEV_PM_OPS(mtip_pci_pm_ops, mtip_pci_suspend, mtip_pci_resume); 4008 4009 /* Structure that describes the PCI driver functions. */ 4010 static struct pci_driver mtip_pci_driver = { 4011 .name = MTIP_DRV_NAME, 4012 .id_table = mtip_pci_tbl, 4013 .probe = mtip_pci_probe, 4014 .remove = mtip_pci_remove, 4015 .driver.pm = &mtip_pci_pm_ops, 4016 .shutdown = mtip_pci_shutdown, 4017 }; 4018 4019 MODULE_DEVICE_TABLE(pci, mtip_pci_tbl); 4020 4021 /* 4022 * Module initialization function. 4023 * 4024 * Called once when the module is loaded. This function allocates a major 4025 * block device number to the Cyclone devices and registers the PCI layer 4026 * of the driver. 4027 * 4028 * Return value 4029 * 0 on success else error code. 4030 */ 4031 static int __init mtip_init(void) 4032 { 4033 int error; 4034 4035 pr_info(MTIP_DRV_NAME " Version " MTIP_DRV_VERSION "\n"); 4036 4037 /* Allocate a major block device number to use with this driver. */ 4038 error = register_blkdev(0, MTIP_DRV_NAME); 4039 if (error <= 0) { 4040 pr_err("Unable to register block device (%d)\n", 4041 error); 4042 return -EBUSY; 4043 } 4044 mtip_major = error; 4045 4046 dfs_parent = debugfs_create_dir("rssd", NULL); 4047 if (IS_ERR_OR_NULL(dfs_parent)) { 4048 pr_warn("Error creating debugfs parent\n"); 4049 dfs_parent = NULL; 4050 } 4051 4052 /* Register our PCI operations. */ 4053 error = pci_register_driver(&mtip_pci_driver); 4054 if (error) { 4055 debugfs_remove(dfs_parent); 4056 unregister_blkdev(mtip_major, MTIP_DRV_NAME); 4057 } 4058 4059 return error; 4060 } 4061 4062 /* 4063 * Module de-initialization function. 4064 * 4065 * Called once when the module is unloaded. This function deallocates 4066 * the major block device number allocated by mtip_init() and 4067 * unregisters the PCI layer of the driver. 4068 * 4069 * Return value 4070 * none 4071 */ 4072 static void __exit mtip_exit(void) 4073 { 4074 /* Release the allocated major block device number. */ 4075 unregister_blkdev(mtip_major, MTIP_DRV_NAME); 4076 4077 /* Unregister the PCI driver. */ 4078 pci_unregister_driver(&mtip_pci_driver); 4079 4080 debugfs_remove_recursive(dfs_parent); 4081 } 4082 4083 MODULE_AUTHOR("Micron Technology, Inc"); 4084 MODULE_DESCRIPTION("Micron RealSSD PCIe Block Driver"); 4085 MODULE_LICENSE("GPL"); 4086 MODULE_VERSION(MTIP_DRV_VERSION); 4087 4088 module_init(mtip_init); 4089 module_exit(mtip_exit); 4090