1 /****************************************************************************** 2 Device driver for Interphase ATM PCI adapter cards 3 Author: Peter Wang <pwang@iphase.com> 4 Interphase Corporation <www.iphase.com> 5 Version: 1.0 6 iphase.h: This is the header file for iphase.c. 7 ******************************************************************************* 8 9 This software may be used and distributed according to the terms 10 of the GNU General Public License (GPL), incorporated herein by reference. 11 Drivers based on this skeleton fall under the GPL and must retain 12 the authorship (implicit copyright) notice. 13 14 This program is distributed in the hope that it will be useful, but 15 WITHOUT ANY WARRANTY; without even the implied warranty of 16 MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU 17 General Public License for more details. 18 19 Modified from an incomplete driver for Interphase 5575 1KVC 1M card which 20 was originally written by Monalisa Agrawal at UNH. Now this driver 21 supports a variety of varients of Interphase ATM PCI (i)Chip adapter 22 card family (See www.iphase.com/products/ClassSheet.cfm?ClassID=ATM) 23 in terms of PHY type, the size of control memory and the size of 24 packet memory. The following are the change log and history: 25 26 Bugfix the Mona's UBR driver. 27 Modify the basic memory allocation and dma logic. 28 Port the driver to the latest kernel from 2.0.46. 29 Complete the ABR logic of the driver, and added the ABR work- 30 around for the hardware anormalies. 31 Add the CBR support. 32 Add the flow control logic to the driver to allow rate-limit VC. 33 Add 4K VC support to the board with 512K control memory. 34 Add the support of all the variants of the Interphase ATM PCI 35 (i)Chip adapter cards including x575 (155M OC3 and UTP155), x525 36 (25M UTP25) and x531 (DS3 and E3). 37 Add SMP support. 38 39 Support and updates available at: ftp://ftp.iphase.com/pub/atm 40 41 *******************************************************************************/ 42 43 #ifndef IPHASE_H 44 #define IPHASE_H 45 46 47 /************************ IADBG DEFINE *********************************/ 48 /* IADebugFlag Bit Map */ 49 #define IF_IADBG_INIT_ADAPTER 0x00000001 // init adapter info 50 #define IF_IADBG_TX 0x00000002 // debug TX 51 #define IF_IADBG_RX 0x00000004 // debug RX 52 #define IF_IADBG_QUERY_INFO 0x00000008 // debug Request call 53 #define IF_IADBG_SHUTDOWN 0x00000010 // debug shutdown event 54 #define IF_IADBG_INTR 0x00000020 // debug interrupt DPC 55 #define IF_IADBG_TXPKT 0x00000040 // debug TX PKT 56 #define IF_IADBG_RXPKT 0x00000080 // debug RX PKT 57 #define IF_IADBG_ERR 0x00000100 // debug system error 58 #define IF_IADBG_EVENT 0x00000200 // debug event 59 #define IF_IADBG_DIS_INTR 0x00001000 // debug disable interrupt 60 #define IF_IADBG_EN_INTR 0x00002000 // debug enable interrupt 61 #define IF_IADBG_LOUD 0x00004000 // debugging info 62 #define IF_IADBG_VERY_LOUD 0x00008000 // excessive debugging info 63 #define IF_IADBG_CBR 0x00100000 // 64 #define IF_IADBG_UBR 0x00200000 // 65 #define IF_IADBG_ABR 0x00400000 // 66 #define IF_IADBG_DESC 0x01000000 // 67 #define IF_IADBG_SUNI_STAT 0x02000000 // suni statistics 68 #define IF_IADBG_RESET 0x04000000 69 70 #define IF_IADBG(f) if (IADebugFlag & (f)) 71 72 #ifdef CONFIG_ATM_IA_DEBUG /* Debug build */ 73 74 #define IF_LOUD(A) IF_IADBG(IF_IADBG_LOUD) { A } 75 #define IF_ERR(A) IF_IADBG(IF_IADBG_ERR) { A } 76 #define IF_VERY_LOUD(A) IF_IADBG( IF_IADBG_VERY_LOUD ) { A } 77 78 #define IF_INIT_ADAPTER(A) IF_IADBG( IF_IADBG_INIT_ADAPTER ) { A } 79 #define IF_INIT(A) IF_IADBG( IF_IADBG_INIT_ADAPTER ) { A } 80 #define IF_SUNI_STAT(A) IF_IADBG( IF_IADBG_SUNI_STAT ) { A } 81 #define IF_QUERY_INFO(A) IF_IADBG( IF_IADBG_QUERY_INFO ) { A } 82 #define IF_COPY_OVER(A) IF_IADBG( IF_IADBG_COPY_OVER ) { A } 83 84 #define IF_INTR(A) IF_IADBG( IF_IADBG_INTR ) { A } 85 #define IF_DIS_INTR(A) IF_IADBG( IF_IADBG_DIS_INTR ) { A } 86 #define IF_EN_INTR(A) IF_IADBG( IF_IADBG_EN_INTR ) { A } 87 88 #define IF_TX(A) IF_IADBG( IF_IADBG_TX ) { A } 89 #define IF_RX(A) IF_IADBG( IF_IADBG_RX ) { A } 90 #define IF_TXPKT(A) IF_IADBG( IF_IADBG_TXPKT ) { A } 91 #define IF_RXPKT(A) IF_IADBG( IF_IADBG_RXPKT ) { A } 92 93 #define IF_SHUTDOWN(A) IF_IADBG(IF_IADBG_SHUTDOWN) { A } 94 #define IF_CBR(A) IF_IADBG( IF_IADBG_CBR ) { A } 95 #define IF_UBR(A) IF_IADBG( IF_IADBG_UBR ) { A } 96 #define IF_ABR(A) IF_IADBG( IF_IADBG_ABR ) { A } 97 #define IF_EVENT(A) IF_IADBG( IF_IADBG_EVENT) { A } 98 99 #else /* free build */ 100 #define IF_LOUD(A) 101 #define IF_VERY_LOUD(A) 102 #define IF_INIT_ADAPTER(A) 103 #define IF_INIT(A) 104 #define IF_SUNI_STAT(A) 105 #define IF_PVC_CHKPKT(A) 106 #define IF_QUERY_INFO(A) 107 #define IF_COPY_OVER(A) 108 #define IF_HANG(A) 109 #define IF_INTR(A) 110 #define IF_DIS_INTR(A) 111 #define IF_EN_INTR(A) 112 #define IF_TX(A) 113 #define IF_RX(A) 114 #define IF_TXDEBUG(A) 115 #define IF_VC(A) 116 #define IF_ERR(A) 117 #define IF_CBR(A) 118 #define IF_UBR(A) 119 #define IF_ABR(A) 120 #define IF_SHUTDOWN(A) 121 #define DbgPrint(A) 122 #define IF_EVENT(A) 123 #define IF_TXPKT(A) 124 #define IF_RXPKT(A) 125 #endif /* CONFIG_ATM_IA_DEBUG */ 126 127 #define ATM_DESC(skb) (skb->protocol) 128 #define IA_SKB_STATE(skb) (skb->protocol) 129 #define IA_DLED 1 130 #define IA_TX_DONE 2 131 132 /* iadbg defines */ 133 #define IA_CMD 0x7749 134 typedef struct { 135 int cmd; 136 int sub_cmd; 137 int len; 138 u32 maddr; 139 int status; 140 void __user *buf; 141 } IA_CMDBUF, *PIA_CMDBUF; 142 143 /* cmds */ 144 #define MEMDUMP 0x01 145 146 /* sub_cmds */ 147 #define MEMDUMP_SEGREG 0x2 148 #define MEMDUMP_DEV 0x1 149 #define MEMDUMP_REASSREG 0x3 150 #define MEMDUMP_FFL 0x4 151 #define READ_REG 0x5 152 #define WAKE_DBG_WAIT 0x6 153 154 /************************ IADBG DEFINE END ***************************/ 155 156 #define Boolean(x) ((x) ? 1 : 0) 157 #define NR_VCI 1024 /* number of VCIs */ 158 #define NR_VCI_LD 10 /* log2(NR_VCI) */ 159 #define NR_VCI_4K 4096 /* number of VCIs */ 160 #define NR_VCI_4K_LD 12 /* log2(NR_VCI) */ 161 #define MEM_VALID 0xfffffff0 /* mask base address with this */ 162 163 #ifndef PCI_VENDOR_ID_IPHASE 164 #define PCI_VENDOR_ID_IPHASE 0x107e 165 #endif 166 #ifndef PCI_DEVICE_ID_IPHASE_5575 167 #define PCI_DEVICE_ID_IPHASE_5575 0x0008 168 #endif 169 #define DEV_LABEL "ia" 170 #define PCR 207692 171 #define ICR 100000 172 #define MCR 0 173 #define TBE 1000 174 #define FRTT 1 175 #define RIF 2 176 #define RDF 4 177 #define NRMCODE 5 /* 0 - 7 */ 178 #define TRMCODE 3 /* 0 - 7 */ 179 #define CDFCODE 6 180 #define ATDFCODE 2 /* 0 - 15 */ 181 182 /*---------------------- Packet/Cell Memory ------------------------*/ 183 #define TX_PACKET_RAM 0x00000 /* start of Trasnmit Packet memory - 0 */ 184 #define DFL_TX_BUF_SZ 10240 /* 10 K buffers */ 185 #define DFL_TX_BUFFERS 50 /* number of packet buffers for Tx 186 - descriptor 0 unused */ 187 #define REASS_RAM_SIZE 0x10000 /* for 64K 1K VC board */ 188 #define RX_PACKET_RAM 0x80000 /* start of Receive Packet memory - 512K */ 189 #define DFL_RX_BUF_SZ 10240 /* 10k buffers */ 190 #define DFL_RX_BUFFERS 50 /* number of packet buffers for Rx 191 - descriptor 0 unused */ 192 193 struct cpcs_trailer 194 { 195 u_short control; 196 u_short length; 197 u_int crc32; 198 }; 199 200 struct cpcs_trailer_desc 201 { 202 struct cpcs_trailer *cpcs; 203 dma_addr_t dma_addr; 204 }; 205 206 struct ia_vcc 207 { 208 int rxing; 209 int txing; 210 int NumCbrEntry; 211 u32 pcr; 212 u32 saved_tx_quota; 213 int flow_inc; 214 struct sk_buff_head txing_skb; 215 int ltimeout; 216 u8 vc_desc_cnt; 217 218 }; 219 220 struct abr_vc_table 221 { 222 u_char status; 223 u_char rdf; 224 u_short air; 225 u_int res[3]; 226 u_int req_rm_cell_data1; 227 u_int req_rm_cell_data2; 228 u_int add_rm_cell_data1; 229 u_int add_rm_cell_data2; 230 }; 231 232 /* 32 byte entries */ 233 struct main_vc 234 { 235 u_short type; 236 #define ABR 0x8000 237 #define UBR 0xc000 238 #define CBR 0x0000 239 /* ABR fields */ 240 u_short nrm; 241 u_short trm; 242 u_short rm_timestamp_hi; 243 u_short rm_timestamp_lo:8, 244 crm:8; 245 u_short remainder; /* ABR and UBR fields - last 10 bits*/ 246 u_short next_vc_sched; 247 u_short present_desc; /* all classes */ 248 u_short last_cell_slot; /* ABR and UBR */ 249 u_short pcr; 250 u_short fraction; 251 u_short icr; 252 u_short atdf; 253 u_short mcr; 254 u_short acr; 255 u_short unack:8, 256 status:8; /* all classes */ 257 #define UIOLI 0x80 258 #define CRC_APPEND 0x40 /* for status field - CRC-32 append */ 259 #define ABR_STATE 0x02 260 261 }; 262 263 264 /* 8 byte entries */ 265 struct ext_vc 266 { 267 u_short atm_hdr1; 268 u_short atm_hdr2; 269 u_short last_desc; 270 u_short out_of_rate_link; /* reserved for UBR and CBR */ 271 }; 272 273 274 #define DLE_ENTRIES 256 275 #define DMA_INT_ENABLE 0x0002 /* use for both Tx and Rx */ 276 #define TX_DLE_PSI 0x0001 277 #define DLE_TOTAL_SIZE (sizeof(struct dle)*DLE_ENTRIES) 278 279 /* Descriptor List Entries (DLE) */ 280 struct dle 281 { 282 u32 sys_pkt_addr; 283 u32 local_pkt_addr; 284 u32 bytes; 285 u16 prq_wr_ptr_data; 286 u16 mode; 287 }; 288 289 struct dle_q 290 { 291 struct dle *start; 292 struct dle *end; 293 struct dle *read; 294 struct dle *write; 295 }; 296 297 struct free_desc_q 298 { 299 int desc; /* Descriptor number */ 300 struct free_desc_q *next; 301 }; 302 303 struct tx_buf_desc { 304 unsigned short desc_mode; 305 unsigned short vc_index; 306 unsigned short res1; /* reserved field */ 307 unsigned short bytes; 308 unsigned short buf_start_hi; 309 unsigned short buf_start_lo; 310 unsigned short res2[10]; /* reserved field */ 311 }; 312 313 314 struct rx_buf_desc { 315 unsigned short desc_mode; 316 unsigned short vc_index; 317 unsigned short vpi; 318 unsigned short bytes; 319 unsigned short buf_start_hi; 320 unsigned short buf_start_lo; 321 unsigned short dma_start_hi; 322 unsigned short dma_start_lo; 323 unsigned short crc_upper; 324 unsigned short crc_lower; 325 unsigned short res:8, timeout:8; 326 unsigned short res2[5]; /* reserved field */ 327 }; 328 329 /*--------SAR stuff ---------------------*/ 330 331 #define EPROM_SIZE 0x40000 /* says 64K in the docs ??? */ 332 #define MAC1_LEN 4 333 #define MAC2_LEN 2 334 335 /*------------ PCI Memory Space Map, 128K SAR memory ----------------*/ 336 #define IPHASE5575_PCI_CONFIG_REG_BASE 0x0000 337 #define IPHASE5575_BUS_CONTROL_REG_BASE 0x1000 /* offsets 0x00 - 0x3c */ 338 #define IPHASE5575_FRAG_CONTROL_REG_BASE 0x2000 339 #define IPHASE5575_REASS_CONTROL_REG_BASE 0x3000 340 #define IPHASE5575_DMA_CONTROL_REG_BASE 0x4000 341 #define IPHASE5575_FRONT_END_REG_BASE IPHASE5575_DMA_CONTROL_REG_BASE 342 #define IPHASE5575_FRAG_CONTROL_RAM_BASE 0x10000 343 #define IPHASE5575_REASS_CONTROL_RAM_BASE 0x20000 344 345 /*------------ Bus interface control registers -----------------*/ 346 #define IPHASE5575_BUS_CONTROL_REG 0x00 347 #define IPHASE5575_BUS_STATUS_REG 0x01 /* actual offset 0x04 */ 348 #define IPHASE5575_MAC1 0x02 349 #define IPHASE5575_REV 0x03 350 #define IPHASE5575_MAC2 0x03 /*actual offset 0x0e-reg 0x0c*/ 351 #define IPHASE5575_EXT_RESET 0x04 352 #define IPHASE5575_INT_RESET 0x05 /* addr 1c ?? reg 0x06 */ 353 #define IPHASE5575_PCI_ADDR_PAGE 0x07 /* reg 0x08, 0x09 ?? */ 354 #define IPHASE5575_EEPROM_ACCESS 0x0a /* actual offset 0x28 */ 355 #define IPHASE5575_CELL_FIFO_QUEUE_SZ 0x0b 356 #define IPHASE5575_CELL_FIFO_MARK_STATE 0x0c 357 #define IPHASE5575_CELL_FIFO_READ_PTR 0x0d 358 #define IPHASE5575_CELL_FIFO_WRITE_PTR 0x0e 359 #define IPHASE5575_CELL_FIFO_CELLS_AVL 0x0f /* actual offset 0x3c */ 360 361 /* Bus Interface Control Register bits */ 362 #define CTRL_FE_RST 0x80000000 363 #define CTRL_LED 0x40000000 364 #define CTRL_25MBPHY 0x10000000 365 #define CTRL_ENCMBMEM 0x08000000 366 #define CTRL_ENOFFSEG 0x01000000 367 #define CTRL_ERRMASK 0x00400000 368 #define CTRL_DLETMASK 0x00100000 369 #define CTRL_DLERMASK 0x00080000 370 #define CTRL_FEMASK 0x00040000 371 #define CTRL_SEGMASK 0x00020000 372 #define CTRL_REASSMASK 0x00010000 373 #define CTRL_CSPREEMPT 0x00002000 374 #define CTRL_B128 0x00000200 375 #define CTRL_B64 0x00000100 376 #define CTRL_B48 0x00000080 377 #define CTRL_B32 0x00000040 378 #define CTRL_B16 0x00000020 379 #define CTRL_B8 0x00000010 380 381 /* Bus Interface Status Register bits */ 382 #define STAT_CMEMSIZ 0xc0000000 383 #define STAT_ADPARCK 0x20000000 384 #define STAT_RESVD 0x1fffff80 385 #define STAT_ERRINT 0x00000040 386 #define STAT_MARKINT 0x00000020 387 #define STAT_DLETINT 0x00000010 388 #define STAT_DLERINT 0x00000008 389 #define STAT_FEINT 0x00000004 390 #define STAT_SEGINT 0x00000002 391 #define STAT_REASSINT 0x00000001 392 393 394 /*--------------- Segmentation control registers -----------------*/ 395 /* The segmentation registers are 16 bits access and the addresses 396 are defined as such so the addresses are the actual "offsets" */ 397 #define IDLEHEADHI 0x00 398 #define IDLEHEADLO 0x01 399 #define MAXRATE 0x02 400 /* Values for MAXRATE register for 155Mbps and 25.6 Mbps operation */ 401 #define RATE155 0x64b1 // 16 bits float format 402 #define MAX_ATM_155 352768 // Cells/second p.118 403 #define RATE25 0x5f9d 404 405 #define STPARMS 0x03 406 #define STPARMS_1K 0x008c 407 #define STPARMS_2K 0x0049 408 #define STPARMS_4K 0x0026 409 #define COMP_EN 0x4000 410 #define CBR_EN 0x2000 411 #define ABR_EN 0x0800 412 #define UBR_EN 0x0400 413 414 #define ABRUBR_ARB 0x04 415 #define RM_TYPE 0x05 416 /*Value for RM_TYPE register for ATM Forum Traffic Mangement4.0 support*/ 417 #define RM_TYPE_4_0 0x0100 418 419 #define SEG_COMMAND_REG 0x17 420 /* Values for the command register */ 421 #define RESET_SEG 0x0055 422 #define RESET_SEG_STATE 0x00aa 423 #define RESET_TX_CELL_CTR 0x00cc 424 425 #define CBR_PTR_BASE 0x20 426 #define ABR_SBPTR_BASE 0x22 427 #define UBR_SBPTR_BASE 0x23 428 #define ABRWQ_BASE 0x26 429 #define UBRWQ_BASE 0x27 430 #define VCT_BASE 0x28 431 #define VCTE_BASE 0x29 432 #define CBR_TAB_BEG 0x2c 433 #define CBR_TAB_END 0x2d 434 #define PRQ_ST_ADR 0x30 435 #define PRQ_ED_ADR 0x31 436 #define PRQ_RD_PTR 0x32 437 #define PRQ_WR_PTR 0x33 438 #define TCQ_ST_ADR 0x34 439 #define TCQ_ED_ADR 0x35 440 #define TCQ_RD_PTR 0x36 441 #define TCQ_WR_PTR 0x37 442 #define SEG_QUEUE_BASE 0x40 443 #define SEG_DESC_BASE 0x41 444 #define MODE_REG_0 0x45 445 #define T_ONLINE 0x0002 /* (i)chipSAR is online */ 446 447 #define MODE_REG_1 0x46 448 #define MODE_REG_1_VAL 0x0400 /*for propoer device operation*/ 449 450 #define SEG_INTR_STATUS_REG 0x47 451 #define SEG_MASK_REG 0x48 452 #define TRANSMIT_DONE 0x0200 453 #define TCQ_NOT_EMPTY 0x1000 /* this can be used for both the interrupt 454 status registers as well as the mask register */ 455 456 #define CELL_CTR_HIGH_AUTO 0x49 457 #define CELL_CTR_HIGH_NOAUTO 0xc9 458 #define CELL_CTR_LO_AUTO 0x4a 459 #define CELL_CTR_LO_NOAUTO 0xca 460 461 /* Diagnostic registers */ 462 #define NEXTDESC 0x59 463 #define NEXTVC 0x5a 464 #define PSLOTCNT 0x5d 465 #define NEWDN 0x6a 466 #define NEWVC 0x6b 467 #define SBPTR 0x6c 468 #define ABRWQ_WRPTR 0x6f 469 #define ABRWQ_RDPTR 0x70 470 #define UBRWQ_WRPTR 0x71 471 #define UBRWQ_RDPTR 0x72 472 #define CBR_VC 0x73 473 #define ABR_SBVC 0x75 474 #define UBR_SBVC 0x76 475 #define ABRNEXTLINK 0x78 476 #define UBRNEXTLINK 0x79 477 478 479 /*----------------- Reassembly control registers ---------------------*/ 480 /* The reassembly registers are 16 bits access and the addresses 481 are defined as such so the addresses are the actual "offsets" */ 482 #define MODE_REG 0x00 483 #define R_ONLINE 0x0002 /* (i)chip is online */ 484 #define IGN_RAW_FL 0x0004 485 486 #define PROTOCOL_ID 0x01 487 #define REASS_MASK_REG 0x02 488 #define REASS_INTR_STATUS_REG 0x03 489 /* Interrupt Status register bits */ 490 #define RX_PKT_CTR_OF 0x8000 491 #define RX_ERR_CTR_OF 0x4000 492 #define RX_CELL_CTR_OF 0x1000 493 #define RX_FREEQ_EMPT 0x0200 494 #define RX_EXCPQ_FL 0x0080 495 #define RX_RAWQ_FL 0x0010 496 #define RX_EXCP_RCVD 0x0008 497 #define RX_PKT_RCVD 0x0004 498 #define RX_RAW_RCVD 0x0001 499 500 #define DRP_PKT_CNTR 0x04 501 #define ERR_CNTR 0x05 502 #define RAW_BASE_ADR 0x08 503 #define CELL_CTR0 0x0c 504 #define CELL_CTR1 0x0d 505 #define REASS_COMMAND_REG 0x0f 506 /* Values for command register */ 507 #define RESET_REASS 0x0055 508 #define RESET_REASS_STATE 0x00aa 509 #define RESET_DRP_PKT_CNTR 0x00f1 510 #define RESET_ERR_CNTR 0x00f2 511 #define RESET_CELL_CNTR 0x00f8 512 #define RESET_REASS_ALL_REGS 0x00ff 513 514 #define REASS_DESC_BASE 0x10 515 #define VC_LKUP_BASE 0x11 516 #define REASS_TABLE_BASE 0x12 517 #define REASS_QUEUE_BASE 0x13 518 #define PKT_TM_CNT 0x16 519 #define TMOUT_RANGE 0x17 520 #define INTRVL_CNTR 0x18 521 #define TMOUT_INDX 0x19 522 #define VP_LKUP_BASE 0x1c 523 #define VP_FILTER 0x1d 524 #define ABR_LKUP_BASE 0x1e 525 #define FREEQ_ST_ADR 0x24 526 #define FREEQ_ED_ADR 0x25 527 #define FREEQ_RD_PTR 0x26 528 #define FREEQ_WR_PTR 0x27 529 #define PCQ_ST_ADR 0x28 530 #define PCQ_ED_ADR 0x29 531 #define PCQ_RD_PTR 0x2a 532 #define PCQ_WR_PTR 0x2b 533 #define EXCP_Q_ST_ADR 0x2c 534 #define EXCP_Q_ED_ADR 0x2d 535 #define EXCP_Q_RD_PTR 0x2e 536 #define EXCP_Q_WR_PTR 0x2f 537 #define CC_FIFO_ST_ADR 0x34 538 #define CC_FIFO_ED_ADR 0x35 539 #define CC_FIFO_RD_PTR 0x36 540 #define CC_FIFO_WR_PTR 0x37 541 #define STATE_REG 0x38 542 #define BUF_SIZE 0x42 543 #define XTRA_RM_OFFSET 0x44 544 #define DRP_PKT_CNTR_NC 0x84 545 #define ERR_CNTR_NC 0x85 546 #define CELL_CNTR0_NC 0x8c 547 #define CELL_CNTR1_NC 0x8d 548 549 /* State Register bits */ 550 #define EXCPQ_EMPTY 0x0040 551 #define PCQ_EMPTY 0x0010 552 #define FREEQ_EMPTY 0x0004 553 554 555 /*----------------- Front End registers/ DMA control --------------*/ 556 /* There is a lot of documentation error regarding these offsets ??? 557 eg:- 2 offsets given 800, a00 for rx counter 558 similarly many others 559 Remember again that the offsets are to be 4*register number, so 560 correct the #defines here 561 */ 562 #define IPHASE5575_TX_COUNTER 0x200 /* offset - 0x800 */ 563 #define IPHASE5575_RX_COUNTER 0x280 /* offset - 0xa00 */ 564 #define IPHASE5575_TX_LIST_ADDR 0x300 /* offset - 0xc00 */ 565 #define IPHASE5575_RX_LIST_ADDR 0x380 /* offset - 0xe00 */ 566 567 /*--------------------------- RAM ---------------------------*/ 568 /* These memory maps are actually offsets from the segmentation and reassembly RAM base addresses */ 569 570 /* Segmentation Control Memory map */ 571 #define TX_DESC_BASE 0x0000 /* Buffer Decriptor Table */ 572 #define TX_COMP_Q 0x1000 /* Transmit Complete Queue */ 573 #define PKT_RDY_Q 0x1400 /* Packet Ready Queue */ 574 #define CBR_SCHED_TABLE 0x1800 /* CBR Table */ 575 #define UBR_SCHED_TABLE 0x3000 /* UBR Table */ 576 #define UBR_WAIT_Q 0x4000 /* UBR Wait Queue */ 577 #define ABR_SCHED_TABLE 0x5000 /* ABR Table */ 578 #define ABR_WAIT_Q 0x5800 /* ABR Wait Queue */ 579 #define EXT_VC_TABLE 0x6000 /* Extended VC Table */ 580 #define MAIN_VC_TABLE 0x8000 /* Main VC Table */ 581 #define SCHEDSZ 1024 /* ABR and UBR Scheduling Table size */ 582 #define TX_DESC_TABLE_SZ 128 /* Number of entries in the Transmit 583 Buffer Descriptor Table */ 584 585 /* These are used as table offsets in Descriptor Table address generation */ 586 #define DESC_MODE 0x0 587 #define VC_INDEX 0x1 588 #define BYTE_CNT 0x3 589 #define PKT_START_HI 0x4 590 #define PKT_START_LO 0x5 591 592 /* Descriptor Mode Word Bits */ 593 #define EOM_EN 0x0800 594 #define AAL5 0x0100 595 #define APP_CRC32 0x0400 596 #define CMPL_INT 0x1000 597 598 #define TABLE_ADDRESS(db, dn, to) \ 599 (((unsigned long)(db & 0x04)) << 16) | (dn << 5) | (to << 1) 600 601 /* Reassembly Control Memory Map */ 602 #define RX_DESC_BASE 0x0000 /* Buffer Descriptor Table */ 603 #define VP_TABLE 0x5c00 /* VP Table */ 604 #define EXCEPTION_Q 0x5e00 /* Exception Queue */ 605 #define FREE_BUF_DESC_Q 0x6000 /* Free Buffer Descriptor Queue */ 606 #define PKT_COMP_Q 0x6800 /* Packet Complete Queue */ 607 #define REASS_TABLE 0x7000 /* Reassembly Table */ 608 #define RX_VC_TABLE 0x7800 /* VC Table */ 609 #define ABR_VC_TABLE 0x8000 /* ABR VC Table */ 610 #define RX_DESC_TABLE_SZ 736 /* Number of entries in the Receive 611 Buffer Descriptor Table */ 612 #define VP_TABLE_SZ 256 /* Number of entries in VPTable */ 613 #define RX_VC_TABLE_SZ 1024 /* Number of entries in VC Table */ 614 #define REASS_TABLE_SZ 1024 /* Number of entries in Reassembly Table */ 615 /* Buffer Descriptor Table */ 616 #define RX_ACT 0x8000 617 #define RX_VPVC 0x4000 618 #define RX_CNG 0x0040 619 #define RX_CER 0x0008 620 #define RX_PTE 0x0004 621 #define RX_OFL 0x0002 622 #define NUM_RX_EXCP 32 623 624 /* Reassembly Table */ 625 #define NO_AAL5_PKT 0x0000 626 #define AAL5_PKT_REASSEMBLED 0x4000 627 #define AAL5_PKT_TERMINATED 0x8000 628 #define RAW_PKT 0xc000 629 #define REASS_ABR 0x2000 630 631 /*-------------------- Base Registers --------------------*/ 632 #define REG_BASE IPHASE5575_BUS_CONTROL_REG_BASE 633 #define RAM_BASE IPHASE5575_FRAG_CONTROL_RAM_BASE 634 #define PHY_BASE IPHASE5575_FRONT_END_REG_BASE 635 #define SEG_BASE IPHASE5575_FRAG_CONTROL_REG_BASE 636 #define REASS_BASE IPHASE5575_REASS_CONTROL_REG_BASE 637 638 typedef volatile u_int ffreg_t; 639 typedef u_int rreg_t; 640 641 typedef struct _ffredn_t { 642 ffreg_t idlehead_high; /* Idle cell header (high) */ 643 ffreg_t idlehead_low; /* Idle cell header (low) */ 644 ffreg_t maxrate; /* Maximum rate */ 645 ffreg_t stparms; /* Traffic Management Parameters */ 646 ffreg_t abrubr_abr; /* ABRUBR Priority Byte 1, TCR Byte 0 */ 647 ffreg_t rm_type; /* */ 648 u_int filler5[0x17 - 0x06]; 649 ffreg_t cmd_reg; /* Command register */ 650 u_int filler18[0x20 - 0x18]; 651 ffreg_t cbr_base; /* CBR Pointer Base */ 652 ffreg_t vbr_base; /* VBR Pointer Base */ 653 ffreg_t abr_base; /* ABR Pointer Base */ 654 ffreg_t ubr_base; /* UBR Pointer Base */ 655 u_int filler24; 656 ffreg_t vbrwq_base; /* VBR Wait Queue Base */ 657 ffreg_t abrwq_base; /* ABR Wait Queue Base */ 658 ffreg_t ubrwq_base; /* UBR Wait Queue Base */ 659 ffreg_t vct_base; /* Main VC Table Base */ 660 ffreg_t vcte_base; /* Extended Main VC Table Base */ 661 u_int filler2a[0x2C - 0x2A]; 662 ffreg_t cbr_tab_beg; /* CBR Table Begin */ 663 ffreg_t cbr_tab_end; /* CBR Table End */ 664 ffreg_t cbr_pointer; /* CBR Pointer */ 665 u_int filler2f[0x30 - 0x2F]; 666 ffreg_t prq_st_adr; /* Packet Ready Queue Start Address */ 667 ffreg_t prq_ed_adr; /* Packet Ready Queue End Address */ 668 ffreg_t prq_rd_ptr; /* Packet Ready Queue read pointer */ 669 ffreg_t prq_wr_ptr; /* Packet Ready Queue write pointer */ 670 ffreg_t tcq_st_adr; /* Transmit Complete Queue Start Address*/ 671 ffreg_t tcq_ed_adr; /* Transmit Complete Queue End Address */ 672 ffreg_t tcq_rd_ptr; /* Transmit Complete Queue read pointer */ 673 ffreg_t tcq_wr_ptr; /* Transmit Complete Queue write pointer*/ 674 u_int filler38[0x40 - 0x38]; 675 ffreg_t queue_base; /* Base address for PRQ and TCQ */ 676 ffreg_t desc_base; /* Base address of descriptor table */ 677 u_int filler42[0x45 - 0x42]; 678 ffreg_t mode_reg_0; /* Mode register 0 */ 679 ffreg_t mode_reg_1; /* Mode register 1 */ 680 ffreg_t intr_status_reg;/* Interrupt Status register */ 681 ffreg_t mask_reg; /* Mask Register */ 682 ffreg_t cell_ctr_high1; /* Total cell transfer count (high) */ 683 ffreg_t cell_ctr_lo1; /* Total cell transfer count (low) */ 684 ffreg_t state_reg; /* Status register */ 685 u_int filler4c[0x58 - 0x4c]; 686 ffreg_t curr_desc_num; /* Contains the current descriptor num */ 687 ffreg_t next_desc; /* Next descriptor */ 688 ffreg_t next_vc; /* Next VC */ 689 u_int filler5b[0x5d - 0x5b]; 690 ffreg_t present_slot_cnt;/* Present slot count */ 691 u_int filler5e[0x6a - 0x5e]; 692 ffreg_t new_desc_num; /* New descriptor number */ 693 ffreg_t new_vc; /* New VC */ 694 ffreg_t sched_tbl_ptr; /* Schedule table pointer */ 695 ffreg_t vbrwq_wptr; /* VBR wait queue write pointer */ 696 ffreg_t vbrwq_rptr; /* VBR wait queue read pointer */ 697 ffreg_t abrwq_wptr; /* ABR wait queue write pointer */ 698 ffreg_t abrwq_rptr; /* ABR wait queue read pointer */ 699 ffreg_t ubrwq_wptr; /* UBR wait queue write pointer */ 700 ffreg_t ubrwq_rptr; /* UBR wait queue read pointer */ 701 ffreg_t cbr_vc; /* CBR VC */ 702 ffreg_t vbr_sb_vc; /* VBR SB VC */ 703 ffreg_t abr_sb_vc; /* ABR SB VC */ 704 ffreg_t ubr_sb_vc; /* UBR SB VC */ 705 ffreg_t vbr_next_link; /* VBR next link */ 706 ffreg_t abr_next_link; /* ABR next link */ 707 ffreg_t ubr_next_link; /* UBR next link */ 708 u_int filler7a[0x7c-0x7a]; 709 ffreg_t out_rate_head; /* Out of rate head */ 710 u_int filler7d[0xca-0x7d]; /* pad out to full address space */ 711 ffreg_t cell_ctr_high1_nc;/* Total cell transfer count (high) */ 712 ffreg_t cell_ctr_lo1_nc;/* Total cell transfer count (low) */ 713 u_int fillercc[0x100-0xcc]; /* pad out to full address space */ 714 } ffredn_t; 715 716 typedef struct _rfredn_t { 717 rreg_t mode_reg_0; /* Mode register 0 */ 718 rreg_t protocol_id; /* Protocol ID */ 719 rreg_t mask_reg; /* Mask Register */ 720 rreg_t intr_status_reg;/* Interrupt status register */ 721 rreg_t drp_pkt_cntr; /* Dropped packet cntr (clear on read) */ 722 rreg_t err_cntr; /* Error Counter (cleared on read) */ 723 u_int filler6[0x08 - 0x06]; 724 rreg_t raw_base_adr; /* Base addr for raw cell Q */ 725 u_int filler2[0x0c - 0x09]; 726 rreg_t cell_ctr0; /* Cell Counter 0 (cleared when read) */ 727 rreg_t cell_ctr1; /* Cell Counter 1 (cleared when read) */ 728 u_int filler3[0x0f - 0x0e]; 729 rreg_t cmd_reg; /* Command register */ 730 rreg_t desc_base; /* Base address for description table */ 731 rreg_t vc_lkup_base; /* Base address for VC lookup table */ 732 rreg_t reass_base; /* Base address for reassembler table */ 733 rreg_t queue_base; /* Base address for Communication queue */ 734 u_int filler14[0x16 - 0x14]; 735 rreg_t pkt_tm_cnt; /* Packet Timeout and count register */ 736 rreg_t tmout_range; /* Range of reassembley IDs for timeout */ 737 rreg_t intrvl_cntr; /* Packet aging interval counter */ 738 rreg_t tmout_indx; /* index of pkt being tested for aging */ 739 u_int filler1a[0x1c - 0x1a]; 740 rreg_t vp_lkup_base; /* Base address for VP lookup table */ 741 rreg_t vp_filter; /* VP filter register */ 742 rreg_t abr_lkup_base; /* Base address of ABR VC Table */ 743 u_int filler1f[0x24 - 0x1f]; 744 rreg_t fdq_st_adr; /* Free desc queue start address */ 745 rreg_t fdq_ed_adr; /* Free desc queue end address */ 746 rreg_t fdq_rd_ptr; /* Free desc queue read pointer */ 747 rreg_t fdq_wr_ptr; /* Free desc queue write pointer */ 748 rreg_t pcq_st_adr; /* Packet Complete queue start address */ 749 rreg_t pcq_ed_adr; /* Packet Complete queue end address */ 750 rreg_t pcq_rd_ptr; /* Packet Complete queue read pointer */ 751 rreg_t pcq_wr_ptr; /* Packet Complete queue write pointer */ 752 rreg_t excp_st_adr; /* Exception queue start address */ 753 rreg_t excp_ed_adr; /* Exception queue end address */ 754 rreg_t excp_rd_ptr; /* Exception queue read pointer */ 755 rreg_t excp_wr_ptr; /* Exception queue write pointer */ 756 u_int filler30[0x34 - 0x30]; 757 rreg_t raw_st_adr; /* Raw Cell start address */ 758 rreg_t raw_ed_adr; /* Raw Cell end address */ 759 rreg_t raw_rd_ptr; /* Raw Cell read pointer */ 760 rreg_t raw_wr_ptr; /* Raw Cell write pointer */ 761 rreg_t state_reg; /* State Register */ 762 u_int filler39[0x42 - 0x39]; 763 rreg_t buf_size; /* Buffer size */ 764 u_int filler43; 765 rreg_t xtra_rm_offset; /* Offset of the additional turnaround RM */ 766 u_int filler45[0x84 - 0x45]; 767 rreg_t drp_pkt_cntr_nc;/* Dropped Packet cntr, Not clear on rd */ 768 rreg_t err_cntr_nc; /* Error Counter, Not clear on read */ 769 u_int filler86[0x8c - 0x86]; 770 rreg_t cell_ctr0_nc; /* Cell Counter 0, Not clear on read */ 771 rreg_t cell_ctr1_nc; /* Cell Counter 1, Not clear on read */ 772 u_int filler8e[0x100-0x8e]; /* pad out to full address space */ 773 } rfredn_t; 774 775 typedef struct { 776 /* Atlantic */ 777 ffredn_t ffredn; /* F FRED */ 778 rfredn_t rfredn; /* R FRED */ 779 } ia_regs_t; 780 781 typedef struct { 782 u_short f_vc_type; /* VC type */ 783 u_short f_nrm; /* Nrm */ 784 u_short f_nrmexp; /* Nrm Exp */ 785 u_short reserved6; /* */ 786 u_short f_crm; /* Crm */ 787 u_short reserved10; /* Reserved */ 788 u_short reserved12; /* Reserved */ 789 u_short reserved14; /* Reserved */ 790 u_short last_cell_slot; /* last_cell_slot_count */ 791 u_short f_pcr; /* Peak Cell Rate */ 792 u_short fraction; /* fraction */ 793 u_short f_icr; /* Initial Cell Rate */ 794 u_short f_cdf; /* */ 795 u_short f_mcr; /* Minimum Cell Rate */ 796 u_short f_acr; /* Allowed Cell Rate */ 797 u_short f_status; /* */ 798 } f_vc_abr_entry; 799 800 typedef struct { 801 u_short r_status_rdf; /* status + RDF */ 802 u_short r_air; /* AIR */ 803 u_short reserved4[14]; /* Reserved */ 804 } r_vc_abr_entry; 805 806 #define MRM 3 807 808 typedef struct srv_cls_param { 809 u32 class_type; /* CBR/VBR/ABR/UBR; use the enum above */ 810 u32 pcr; /* Peak Cell Rate (24-bit) */ 811 /* VBR parameters */ 812 u32 scr; /* sustainable cell rate */ 813 u32 max_burst_size; /* ?? cell rate or data rate */ 814 815 /* ABR only UNI 4.0 Parameters */ 816 u32 mcr; /* Min Cell Rate (24-bit) */ 817 u32 icr; /* Initial Cell Rate (24-bit) */ 818 u32 tbe; /* Transient Buffer Exposure (24-bit) */ 819 u32 frtt; /* Fixed Round Trip Time (24-bit) */ 820 821 #if 0 /* Additional Parameters of TM 4.0 */ 822 bits 31 30 29 28 27-25 24-22 21-19 18-9 823 ----------------------------------------------------------------------------- 824 | NRM present | TRM prsnt | CDF prsnt | ADTF prsnt | NRM | TRM | CDF | ADTF | 825 ----------------------------------------------------------------------------- 826 #endif /* 0 */ 827 828 u8 nrm; /* Max # of Cells for each forward RM 829 cell (3-bit) */ 830 u8 trm; /* Time between forward RM cells (3-bit) */ 831 u16 adtf; /* ACR Decrease Time Factor (10-bit) */ 832 u8 cdf; /* Cutoff Decrease Factor (3-bit) */ 833 u8 rif; /* Rate Increment Factor (4-bit) */ 834 u8 rdf; /* Rate Decrease Factor (4-bit) */ 835 u8 reserved; /* 8 bits to keep structure word aligned */ 836 } srv_cls_param_t; 837 838 struct testTable_t { 839 u16 lastTime; 840 u16 fract; 841 u8 vc_status; 842 }; 843 844 typedef struct { 845 u16 vci; 846 u16 error; 847 } RX_ERROR_Q; 848 849 typedef struct { 850 u8 active: 1; 851 u8 abr: 1; 852 u8 ubr: 1; 853 u8 cnt: 5; 854 #define VC_ACTIVE 0x01 855 #define VC_ABR 0x02 856 #define VC_UBR 0x04 857 } vcstatus_t; 858 859 struct ia_rfL_t { 860 u32 fdq_st; /* Free desc queue start address */ 861 u32 fdq_ed; /* Free desc queue end address */ 862 u32 fdq_rd; /* Free desc queue read pointer */ 863 u32 fdq_wr; /* Free desc queue write pointer */ 864 u32 pcq_st; /* Packet Complete queue start address */ 865 u32 pcq_ed; /* Packet Complete queue end address */ 866 u32 pcq_rd; /* Packet Complete queue read pointer */ 867 u32 pcq_wr; /* Packet Complete queue write pointer */ 868 }; 869 870 struct ia_ffL_t { 871 u32 prq_st; /* Packet Ready Queue Start Address */ 872 u32 prq_ed; /* Packet Ready Queue End Address */ 873 u32 prq_wr; /* Packet Ready Queue write pointer */ 874 u32 tcq_st; /* Transmit Complete Queue Start Address*/ 875 u32 tcq_ed; /* Transmit Complete Queue End Address */ 876 u32 tcq_rd; /* Transmit Complete Queue read pointer */ 877 }; 878 879 struct desc_tbl_t { 880 u32 timestamp; 881 struct ia_vcc *iavcc; 882 struct sk_buff *txskb; 883 }; 884 885 typedef struct ia_rtn_q { 886 struct desc_tbl_t data; 887 struct ia_rtn_q *next, *tail; 888 } IARTN_Q; 889 890 #define SUNI_LOSV 0x04 891 enum ia_suni { 892 SUNI_MASTER_RESET = 0x000, /* SUNI Master Reset and Identity */ 893 SUNI_MASTER_CONFIG = 0x004, /* SUNI Master Configuration */ 894 SUNI_MASTER_INTR_STAT = 0x008, /* SUNI Master Interrupt Status */ 895 SUNI_RESERVED1 = 0x00c, /* Reserved */ 896 SUNI_MASTER_CLK_MONITOR = 0x010, /* SUNI Master Clock Monitor */ 897 SUNI_MASTER_CONTROL = 0x014, /* SUNI Master Clock Monitor */ 898 /* Reserved (10) */ 899 SUNI_RSOP_CONTROL = 0x040, /* RSOP Control/Interrupt Enable */ 900 SUNI_RSOP_STATUS = 0x044, /* RSOP Status/Interrupt States */ 901 SUNI_RSOP_SECTION_BIP8L = 0x048, /* RSOP Section BIP-8 LSB */ 902 SUNI_RSOP_SECTION_BIP8M = 0x04c, /* RSOP Section BIP-8 MSB */ 903 904 SUNI_TSOP_CONTROL = 0x050, /* TSOP Control */ 905 SUNI_TSOP_DIAG = 0x054, /* TSOP Disgnostics */ 906 /* Reserved (2) */ 907 SUNI_RLOP_CS = 0x060, /* RLOP Control/Status */ 908 SUNI_RLOP_INTR = 0x064, /* RLOP Interrupt Enable/Status */ 909 SUNI_RLOP_LINE_BIP24L = 0x068, /* RLOP Line BIP-24 LSB */ 910 SUNI_RLOP_LINE_BIP24 = 0x06c, /* RLOP Line BIP-24 */ 911 SUNI_RLOP_LINE_BIP24M = 0x070, /* RLOP Line BIP-24 MSB */ 912 SUNI_RLOP_LINE_FEBEL = 0x074, /* RLOP Line FEBE LSB */ 913 SUNI_RLOP_LINE_FEBE = 0x078, /* RLOP Line FEBE */ 914 SUNI_RLOP_LINE_FEBEM = 0x07c, /* RLOP Line FEBE MSB */ 915 916 SUNI_TLOP_CONTROL = 0x080, /* TLOP Control */ 917 SUNI_TLOP_DISG = 0x084, /* TLOP Disgnostics */ 918 /* Reserved (14) */ 919 SUNI_RPOP_CS = 0x0c0, /* RPOP Status/Control */ 920 SUNI_RPOP_INTR = 0x0c4, /* RPOP Interrupt/Status */ 921 SUNI_RPOP_RESERVED = 0x0c8, /* RPOP Reserved */ 922 SUNI_RPOP_INTR_ENA = 0x0cc, /* RPOP Interrupt Enable */ 923 /* Reserved (3) */ 924 SUNI_RPOP_PATH_SIG = 0x0dc, /* RPOP Path Signal Label */ 925 SUNI_RPOP_BIP8L = 0x0e0, /* RPOP Path BIP-8 LSB */ 926 SUNI_RPOP_BIP8M = 0x0e4, /* RPOP Path BIP-8 MSB */ 927 SUNI_RPOP_FEBEL = 0x0e8, /* RPOP Path FEBE LSB */ 928 SUNI_RPOP_FEBEM = 0x0ec, /* RPOP Path FEBE MSB */ 929 /* Reserved (4) */ 930 SUNI_TPOP_CNTRL_DAIG = 0x100, /* TPOP Control/Disgnostics */ 931 SUNI_TPOP_POINTER_CTRL = 0x104, /* TPOP Pointer Control */ 932 SUNI_TPOP_SOURCER_CTRL = 0x108, /* TPOP Source Control */ 933 /* Reserved (2) */ 934 SUNI_TPOP_ARB_PRTL = 0x114, /* TPOP Arbitrary Pointer LSB */ 935 SUNI_TPOP_ARB_PRTM = 0x118, /* TPOP Arbitrary Pointer MSB */ 936 SUNI_TPOP_RESERVED2 = 0x11c, /* TPOP Reserved */ 937 SUNI_TPOP_PATH_SIG = 0x120, /* TPOP Path Signal Lable */ 938 SUNI_TPOP_PATH_STATUS = 0x124, /* TPOP Path Status */ 939 /* Reserved (6) */ 940 SUNI_RACP_CS = 0x140, /* RACP Control/Status */ 941 SUNI_RACP_INTR = 0x144, /* RACP Interrupt Enable/Status */ 942 SUNI_RACP_HDR_PATTERN = 0x148, /* RACP Match Header Pattern */ 943 SUNI_RACP_HDR_MASK = 0x14c, /* RACP Match Header Mask */ 944 SUNI_RACP_CORR_HCS = 0x150, /* RACP Correctable HCS Error Count */ 945 SUNI_RACP_UNCORR_HCS = 0x154, /* RACP Uncorrectable HCS Err Count */ 946 /* Reserved (10) */ 947 SUNI_TACP_CONTROL = 0x180, /* TACP Control */ 948 SUNI_TACP_IDLE_HDR_PAT = 0x184, /* TACP Idle Cell Header Pattern */ 949 SUNI_TACP_IDLE_PAY_PAY = 0x188, /* TACP Idle Cell Payld Octet Patrn */ 950 /* Reserved (5) */ 951 /* Reserved (24) */ 952 /* FIXME: unused but name conflicts. 953 * SUNI_MASTER_TEST = 0x200, SUNI Master Test */ 954 SUNI_RESERVED_TEST = 0x204 /* SUNI Reserved for Test */ 955 }; 956 957 typedef struct _SUNI_STATS_ 958 { 959 u32 valid; // 1 = oc3 PHY card 960 u32 carrier_detect; // GPIN input 961 // RSOP: receive section overhead processor 962 u16 rsop_oof_state; // 1 = out of frame 963 u16 rsop_lof_state; // 1 = loss of frame 964 u16 rsop_los_state; // 1 = loss of signal 965 u32 rsop_los_count; // loss of signal count 966 u32 rsop_bse_count; // section BIP-8 error count 967 // RLOP: receive line overhead processor 968 u16 rlop_ferf_state; // 1 = far end receive failure 969 u16 rlop_lais_state; // 1 = line AIS 970 u32 rlop_lbe_count; // BIP-24 count 971 u32 rlop_febe_count; // FEBE count; 972 // RPOP: receive path overhead processor 973 u16 rpop_lop_state; // 1 = LOP 974 u16 rpop_pais_state; // 1 = path AIS 975 u16 rpop_pyel_state; // 1 = path yellow alert 976 u32 rpop_bip_count; // path BIP-8 error count 977 u32 rpop_febe_count; // path FEBE error count 978 u16 rpop_psig; // path signal label value 979 // RACP: receive ATM cell processor 980 u16 racp_hp_state; // hunt/presync state 981 u32 racp_fu_count; // FIFO underrun count 982 u32 racp_fo_count; // FIFO overrun count 983 u32 racp_chcs_count; // correctable HCS error count 984 u32 racp_uchcs_count; // uncorrectable HCS error count 985 } IA_SUNI_STATS; 986 987 typedef struct iadev_priv { 988 /*-----base pointers into (i)chipSAR+ address space */ 989 u32 __iomem *phy; /* Base pointer into phy (SUNI). */ 990 u32 __iomem *dma; /* Base pointer into DMA control registers. */ 991 u32 __iomem *reg; /* Base pointer to SAR registers. */ 992 u32 __iomem *seg_reg; /* base pointer to segmentation engine 993 internal registers */ 994 u32 __iomem *reass_reg; /* base pointer to reassemble engine 995 internal registers */ 996 u32 __iomem *ram; /* base pointer to SAR RAM */ 997 void __iomem *seg_ram; 998 void __iomem *reass_ram; 999 struct dle_q tx_dle_q; 1000 struct free_desc_q *tx_free_desc_qhead; 1001 struct sk_buff_head tx_dma_q, tx_backlog; 1002 spinlock_t tx_lock; 1003 IARTN_Q tx_return_q; 1004 u32 close_pending; 1005 wait_queue_head_t close_wait; 1006 wait_queue_head_t timeout_wait; 1007 struct cpcs_trailer_desc *tx_buf; 1008 u16 num_tx_desc, tx_buf_sz, rate_limit; 1009 u32 tx_cell_cnt, tx_pkt_cnt; 1010 void __iomem *MAIN_VC_TABLE_ADDR, *EXT_VC_TABLE_ADDR, *ABR_SCHED_TABLE_ADDR; 1011 struct dle_q rx_dle_q; 1012 struct free_desc_q *rx_free_desc_qhead; 1013 struct sk_buff_head rx_dma_q; 1014 spinlock_t rx_lock; 1015 struct atm_vcc **rx_open; /* list of all open VCs */ 1016 u16 num_rx_desc, rx_buf_sz, rxing; 1017 u32 rx_pkt_ram, rx_tmp_cnt; 1018 unsigned long rx_tmp_jif; 1019 void __iomem *RX_DESC_BASE_ADDR; 1020 u32 drop_rxpkt, drop_rxcell, rx_cell_cnt, rx_pkt_cnt; 1021 struct atm_dev *next_board; /* other iphase devices */ 1022 struct pci_dev *pci; 1023 int mem; 1024 unsigned int real_base; /* real and virtual base address */ 1025 void __iomem *base; 1026 unsigned int pci_map_size; /*pci map size of board */ 1027 unsigned char irq; 1028 unsigned char bus; 1029 unsigned char dev_fn; 1030 u_short phy_type; 1031 u_short num_vc, memSize, memType; 1032 struct ia_ffL_t ffL; 1033 struct ia_rfL_t rfL; 1034 /* Suni stat */ 1035 // IA_SUNI_STATS suni_stats; 1036 unsigned char carrier_detect; 1037 /* CBR related */ 1038 // transmit DMA & Receive 1039 unsigned int tx_dma_cnt; // number of elements on dma queue 1040 unsigned int rx_dma_cnt; // number of elements on rx dma queue 1041 unsigned int NumEnabledCBR; // number of CBR VCI's enabled. CBR 1042 // receive MARK for Cell FIFO 1043 unsigned int rx_mark_cnt; // number of elements on mark queue 1044 unsigned int CbrTotEntries; // Total CBR Entries in Scheduling Table. 1045 unsigned int CbrRemEntries; // Remaining CBR Entries in Scheduling Table. 1046 unsigned int CbrEntryPt; // CBR Sched Table Entry Point. 1047 unsigned int Granularity; // CBR Granularity given Table Size. 1048 /* ABR related */ 1049 unsigned int sum_mcr, sum_cbr, LineRate; 1050 unsigned int n_abr; 1051 struct desc_tbl_t *desc_tbl; 1052 u_short host_tcq_wr; 1053 struct testTable_t **testTable; 1054 dma_addr_t tx_dle_dma; 1055 dma_addr_t rx_dle_dma; 1056 } IADEV; 1057 1058 1059 #define INPH_IA_DEV(d) ((IADEV *) (d)->dev_data) 1060 #define INPH_IA_VCC(v) ((struct ia_vcc *) (v)->dev_data) 1061 1062 /******************* IDT77105 25MB/s PHY DEFINE *****************************/ 1063 enum ia_mb25 { 1064 MB25_MASTER_CTRL = 0x00, /* Master control */ 1065 MB25_INTR_STATUS = 0x04, /* Interrupt status */ 1066 MB25_DIAG_CONTROL = 0x08, /* Diagnostic control */ 1067 MB25_LED_HEC = 0x0c, /* LED driver and HEC status/control */ 1068 MB25_LOW_BYTE_COUNTER = 0x10, 1069 MB25_HIGH_BYTE_COUNTER = 0x14 1070 }; 1071 1072 /* 1073 * Master Control 1074 */ 1075 #define MB25_MC_UPLO 0x80 /* UPLO */ 1076 #define MB25_MC_DREC 0x40 /* Discard receive cell errors */ 1077 #define MB25_MC_ECEIO 0x20 /* Enable Cell Error Interrupts Only */ 1078 #define MB25_MC_TDPC 0x10 /* Transmit data parity check */ 1079 #define MB25_MC_DRIC 0x08 /* Discard receive idle cells */ 1080 #define MB25_MC_HALTTX 0x04 /* Halt Tx */ 1081 #define MB25_MC_UMS 0x02 /* UTOPIA mode select */ 1082 #define MB25_MC_ENABLED 0x01 /* Enable interrupt */ 1083 1084 /* 1085 * Interrupt Status 1086 */ 1087 #define MB25_IS_GSB 0x40 /* GOOD Symbol Bit */ 1088 #define MB25_IS_HECECR 0x20 /* HEC error cell received */ 1089 #define MB25_IS_SCR 0x10 /* "Short Cell" Received */ 1090 #define MB25_IS_TPE 0x08 /* Trnamsit Parity Error */ 1091 #define MB25_IS_RSCC 0x04 /* Receive Signal Condition change */ 1092 #define MB25_IS_RCSE 0x02 /* Received Cell Symbol Error */ 1093 #define MB25_IS_RFIFOO 0x01 /* Received FIFO Overrun */ 1094 1095 /* 1096 * Diagnostic Control 1097 */ 1098 #define MB25_DC_FTXCD 0x80 /* Force TxClav deassert */ 1099 #define MB25_DC_RXCOS 0x40 /* RxClav operation select */ 1100 #define MB25_DC_ECEIO 0x20 /* Single/Multi-PHY config select */ 1101 #define MB25_DC_RLFLUSH 0x10 /* Clear receive FIFO */ 1102 #define MB25_DC_IXPE 0x08 /* Insert xmit payload error */ 1103 #define MB25_DC_IXHECE 0x04 /* Insert Xmit HEC Error */ 1104 #define MB25_DC_LB_MASK 0x03 /* Loopback control mask */ 1105 1106 #define MB25_DC_LL 0x03 /* Line Loopback */ 1107 #define MB25_DC_PL 0x02 /* PHY Loopback */ 1108 #define MB25_DC_NM 0x00 1109 1110 #define FE_MASK 0x00F0 1111 #define FE_MULTI_MODE 0x0000 1112 #define FE_SINGLE_MODE 0x0010 1113 #define FE_UTP_OPTION 0x0020 1114 #define FE_25MBIT_PHY 0x0040 1115 #define FE_DS3_PHY 0x0080 /* DS3 */ 1116 #define FE_E3_PHY 0x0090 /* E3 */ 1117 1118 /*********************** SUNI_PM7345 PHY DEFINE HERE *********************/ 1119 enum suni_pm7345 { 1120 SUNI_CONFIG = 0x000, /* SUNI Configuration */ 1121 SUNI_INTR_ENBL = 0x004, /* SUNI Interrupt Enable */ 1122 SUNI_INTR_STAT = 0x008, /* SUNI Interrupt Status */ 1123 SUNI_CONTROL = 0x00c, /* SUNI Control */ 1124 SUNI_ID_RESET = 0x010, /* SUNI Reset and Identity */ 1125 SUNI_DATA_LINK_CTRL = 0x014, 1126 SUNI_RBOC_CONF_INTR_ENBL = 0x018, 1127 SUNI_RBOC_STAT = 0x01c, 1128 SUNI_DS3_FRM_CFG = 0x020, 1129 SUNI_DS3_FRM_INTR_ENBL = 0x024, 1130 SUNI_DS3_FRM_INTR_STAT = 0x028, 1131 SUNI_DS3_FRM_STAT = 0x02c, 1132 SUNI_RFDL_CFG = 0x030, 1133 SUNI_RFDL_ENBL_STAT = 0x034, 1134 SUNI_RFDL_STAT = 0x038, 1135 SUNI_RFDL_DATA = 0x03c, 1136 SUNI_PMON_CHNG = 0x040, 1137 SUNI_PMON_INTR_ENBL_STAT = 0x044, 1138 /* SUNI_RESERVED1 (0x13 - 0x11) */ 1139 SUNI_PMON_LCV_EVT_CNT_LSB = 0x050, 1140 SUNI_PMON_LCV_EVT_CNT_MSB = 0x054, 1141 SUNI_PMON_FBE_EVT_CNT_LSB = 0x058, 1142 SUNI_PMON_FBE_EVT_CNT_MSB = 0x05c, 1143 SUNI_PMON_SEZ_DET_CNT_LSB = 0x060, 1144 SUNI_PMON_SEZ_DET_CNT_MSB = 0x064, 1145 SUNI_PMON_PE_EVT_CNT_LSB = 0x068, 1146 SUNI_PMON_PE_EVT_CNT_MSB = 0x06c, 1147 SUNI_PMON_PPE_EVT_CNT_LSB = 0x070, 1148 SUNI_PMON_PPE_EVT_CNT_MSB = 0x074, 1149 SUNI_PMON_FEBE_EVT_CNT_LSB = 0x078, 1150 SUNI_PMON_FEBE_EVT_CNT_MSB = 0x07c, 1151 SUNI_DS3_TRAN_CFG = 0x080, 1152 SUNI_DS3_TRAN_DIAG = 0x084, 1153 /* SUNI_RESERVED2 (0x23 - 0x21) */ 1154 SUNI_XFDL_CFG = 0x090, 1155 SUNI_XFDL_INTR_ST = 0x094, 1156 SUNI_XFDL_XMIT_DATA = 0x098, 1157 SUNI_XBOC_CODE = 0x09c, 1158 SUNI_SPLR_CFG = 0x0a0, 1159 SUNI_SPLR_INTR_EN = 0x0a4, 1160 SUNI_SPLR_INTR_ST = 0x0a8, 1161 SUNI_SPLR_STATUS = 0x0ac, 1162 SUNI_SPLT_CFG = 0x0b0, 1163 SUNI_SPLT_CNTL = 0x0b4, 1164 SUNI_SPLT_DIAG_G1 = 0x0b8, 1165 SUNI_SPLT_F1 = 0x0bc, 1166 SUNI_CPPM_LOC_METERS = 0x0c0, 1167 SUNI_CPPM_CHG_OF_CPPM_PERF_METR = 0x0c4, 1168 SUNI_CPPM_B1_ERR_CNT_LSB = 0x0c8, 1169 SUNI_CPPM_B1_ERR_CNT_MSB = 0x0cc, 1170 SUNI_CPPM_FRAMING_ERR_CNT_LSB = 0x0d0, 1171 SUNI_CPPM_FRAMING_ERR_CNT_MSB = 0x0d4, 1172 SUNI_CPPM_FEBE_CNT_LSB = 0x0d8, 1173 SUNI_CPPM_FEBE_CNT_MSB = 0x0dc, 1174 SUNI_CPPM_HCS_ERR_CNT_LSB = 0x0e0, 1175 SUNI_CPPM_HCS_ERR_CNT_MSB = 0x0e4, 1176 SUNI_CPPM_IDLE_UN_CELL_CNT_LSB = 0x0e8, 1177 SUNI_CPPM_IDLE_UN_CELL_CNT_MSB = 0x0ec, 1178 SUNI_CPPM_RCV_CELL_CNT_LSB = 0x0f0, 1179 SUNI_CPPM_RCV_CELL_CNT_MSB = 0x0f4, 1180 SUNI_CPPM_XMIT_CELL_CNT_LSB = 0x0f8, 1181 SUNI_CPPM_XMIT_CELL_CNT_MSB = 0x0fc, 1182 SUNI_RXCP_CTRL = 0x100, 1183 SUNI_RXCP_FCTRL = 0x104, 1184 SUNI_RXCP_INTR_EN_STS = 0x108, 1185 SUNI_RXCP_IDLE_PAT_H1 = 0x10c, 1186 SUNI_RXCP_IDLE_PAT_H2 = 0x110, 1187 SUNI_RXCP_IDLE_PAT_H3 = 0x114, 1188 SUNI_RXCP_IDLE_PAT_H4 = 0x118, 1189 SUNI_RXCP_IDLE_MASK_H1 = 0x11c, 1190 SUNI_RXCP_IDLE_MASK_H2 = 0x120, 1191 SUNI_RXCP_IDLE_MASK_H3 = 0x124, 1192 SUNI_RXCP_IDLE_MASK_H4 = 0x128, 1193 SUNI_RXCP_CELL_PAT_H1 = 0x12c, 1194 SUNI_RXCP_CELL_PAT_H2 = 0x130, 1195 SUNI_RXCP_CELL_PAT_H3 = 0x134, 1196 SUNI_RXCP_CELL_PAT_H4 = 0x138, 1197 SUNI_RXCP_CELL_MASK_H1 = 0x13c, 1198 SUNI_RXCP_CELL_MASK_H2 = 0x140, 1199 SUNI_RXCP_CELL_MASK_H3 = 0x144, 1200 SUNI_RXCP_CELL_MASK_H4 = 0x148, 1201 SUNI_RXCP_HCS_CS = 0x14c, 1202 SUNI_RXCP_LCD_CNT_THRESHOLD = 0x150, 1203 /* SUNI_RESERVED3 (0x57 - 0x54) */ 1204 SUNI_TXCP_CTRL = 0x160, 1205 SUNI_TXCP_INTR_EN_STS = 0x164, 1206 SUNI_TXCP_IDLE_PAT_H1 = 0x168, 1207 SUNI_TXCP_IDLE_PAT_H2 = 0x16c, 1208 SUNI_TXCP_IDLE_PAT_H3 = 0x170, 1209 SUNI_TXCP_IDLE_PAT_H4 = 0x174, 1210 SUNI_TXCP_IDLE_PAT_H5 = 0x178, 1211 SUNI_TXCP_IDLE_PAYLOAD = 0x17c, 1212 SUNI_E3_FRM_FRAM_OPTIONS = 0x180, 1213 SUNI_E3_FRM_MAINT_OPTIONS = 0x184, 1214 SUNI_E3_FRM_FRAM_INTR_ENBL = 0x188, 1215 SUNI_E3_FRM_FRAM_INTR_IND_STAT = 0x18c, 1216 SUNI_E3_FRM_MAINT_INTR_ENBL = 0x190, 1217 SUNI_E3_FRM_MAINT_INTR_IND = 0x194, 1218 SUNI_E3_FRM_MAINT_STAT = 0x198, 1219 SUNI_RESERVED4 = 0x19c, 1220 SUNI_E3_TRAN_FRAM_OPTIONS = 0x1a0, 1221 SUNI_E3_TRAN_STAT_DIAG_OPTIONS = 0x1a4, 1222 SUNI_E3_TRAN_BIP_8_ERR_MASK = 0x1a8, 1223 SUNI_E3_TRAN_MAINT_ADAPT_OPTS = 0x1ac, 1224 SUNI_TTB_CTRL = 0x1b0, 1225 SUNI_TTB_TRAIL_TRACE_ID_STAT = 0x1b4, 1226 SUNI_TTB_IND_ADDR = 0x1b8, 1227 SUNI_TTB_IND_DATA = 0x1bc, 1228 SUNI_TTB_EXP_PAYLOAD_TYPE = 0x1c0, 1229 SUNI_TTB_PAYLOAD_TYPE_CTRL_STAT = 0x1c4, 1230 /* SUNI_PAD5 (0x7f - 0x71) */ 1231 SUNI_MASTER_TEST = 0x200, 1232 /* SUNI_PAD6 (0xff - 0x80) */ 1233 }; 1234 1235 #define SUNI_PM7345_T suni_pm7345_t 1236 #define SUNI_PM7345 0x20 /* Suni chip type */ 1237 #define SUNI_PM5346 0x30 /* Suni chip type */ 1238 /* 1239 * SUNI_PM7345 Configuration 1240 */ 1241 #define SUNI_PM7345_CLB 0x01 /* Cell loopback */ 1242 #define SUNI_PM7345_PLB 0x02 /* Payload loopback */ 1243 #define SUNI_PM7345_DLB 0x04 /* Diagnostic loopback */ 1244 #define SUNI_PM7345_LLB 0x80 /* Line loopback */ 1245 #define SUNI_PM7345_E3ENBL 0x40 /* E3 enable bit */ 1246 #define SUNI_PM7345_LOOPT 0x10 /* LOOPT enable bit */ 1247 #define SUNI_PM7345_FIFOBP 0x20 /* FIFO bypass */ 1248 #define SUNI_PM7345_FRMRBP 0x08 /* Framer bypass */ 1249 /* 1250 * DS3 FRMR Interrupt Enable 1251 */ 1252 #define SUNI_DS3_COFAE 0x80 /* Enable change of frame align */ 1253 #define SUNI_DS3_REDE 0x40 /* Enable DS3 RED state intr */ 1254 #define SUNI_DS3_CBITE 0x20 /* Enable Appl ID channel intr */ 1255 #define SUNI_DS3_FERFE 0x10 /* Enable Far End Receive Failure intr*/ 1256 #define SUNI_DS3_IDLE 0x08 /* Enable Idle signal intr */ 1257 #define SUNI_DS3_AISE 0x04 /* Enable Alarm Indication signal intr*/ 1258 #define SUNI_DS3_OOFE 0x02 /* Enable Out of frame intr */ 1259 #define SUNI_DS3_LOSE 0x01 /* Enable Loss of signal intr */ 1260 1261 /* 1262 * DS3 FRMR Status 1263 */ 1264 #define SUNI_DS3_ACE 0x80 /* Additional Configuration Reg */ 1265 #define SUNI_DS3_REDV 0x40 /* DS3 RED state */ 1266 #define SUNI_DS3_CBITV 0x20 /* Application ID channel state */ 1267 #define SUNI_DS3_FERFV 0x10 /* Far End Receive Failure state*/ 1268 #define SUNI_DS3_IDLV 0x08 /* Idle signal state */ 1269 #define SUNI_DS3_AISV 0x04 /* Alarm Indication signal state*/ 1270 #define SUNI_DS3_OOFV 0x02 /* Out of frame state */ 1271 #define SUNI_DS3_LOSV 0x01 /* Loss of signal state */ 1272 1273 /* 1274 * E3 FRMR Interrupt/Status 1275 */ 1276 #define SUNI_E3_CZDI 0x40 /* Consecutive Zeros indicator */ 1277 #define SUNI_E3_LOSI 0x20 /* Loss of signal intr status */ 1278 #define SUNI_E3_LCVI 0x10 /* Line code violation intr */ 1279 #define SUNI_E3_COFAI 0x08 /* Change of frame align intr */ 1280 #define SUNI_E3_OOFI 0x04 /* Out of frame intr status */ 1281 #define SUNI_E3_LOS 0x02 /* Loss of signal state */ 1282 #define SUNI_E3_OOF 0x01 /* Out of frame state */ 1283 1284 /* 1285 * E3 FRMR Maintenance Status 1286 */ 1287 #define SUNI_E3_AISD 0x80 /* Alarm Indication signal state*/ 1288 #define SUNI_E3_FERF_RAI 0x40 /* FERF/RAI indicator */ 1289 #define SUNI_E3_FEBE 0x20 /* Far End Block Error indicator*/ 1290 1291 /* 1292 * RXCP Control/Status 1293 */ 1294 #define SUNI_DS3_HCSPASS 0x80 /* Pass cell with HEC errors */ 1295 #define SUNI_DS3_HCSDQDB 0x40 /* Control octets in HCS calc */ 1296 #define SUNI_DS3_HCSADD 0x20 /* Add coset poly */ 1297 #define SUNI_DS3_HCK 0x10 /* Control FIFO data path integ chk*/ 1298 #define SUNI_DS3_BLOCK 0x08 /* Enable cell filtering */ 1299 #define SUNI_DS3_DSCR 0x04 /* Disable payload descrambling */ 1300 #define SUNI_DS3_OOCDV 0x02 /* Cell delineation state */ 1301 #define SUNI_DS3_FIFORST 0x01 /* Cell FIFO reset */ 1302 1303 /* 1304 * RXCP Interrupt Enable/Status 1305 */ 1306 #define SUNI_DS3_OOCDE 0x80 /* Intr enable, change in CDS */ 1307 #define SUNI_DS3_HCSE 0x40 /* Intr enable, corr HCS errors */ 1308 #define SUNI_DS3_FIFOE 0x20 /* Intr enable, unco HCS errors */ 1309 #define SUNI_DS3_OOCDI 0x10 /* SYNC state */ 1310 #define SUNI_DS3_UHCSI 0x08 /* Uncorr. HCS errors detected */ 1311 #define SUNI_DS3_COCAI 0x04 /* Corr. HCS errors detected */ 1312 #define SUNI_DS3_FOVRI 0x02 /* FIFO overrun */ 1313 #define SUNI_DS3_FUDRI 0x01 /* FIFO underrun */ 1314 1315 ///////////////////SUNI_PM7345 PHY DEFINE END ///////////////////////////// 1316 1317 /* ia_eeprom define*/ 1318 #define MEM_SIZE_MASK 0x000F /* mask of 4 bits defining memory size*/ 1319 #define MEM_SIZE_128K 0x0000 /* board has 128k buffer */ 1320 #define MEM_SIZE_512K 0x0001 /* board has 512K of buffer */ 1321 #define MEM_SIZE_1M 0x0002 /* board has 1M of buffer */ 1322 /* 0x3 to 0xF are reserved for future */ 1323 1324 #define FE_MASK 0x00F0 /* mask of 4 bits defining FE type */ 1325 #define FE_MULTI_MODE 0x0000 /* 155 MBit multimode fiber */ 1326 #define FE_SINGLE_MODE 0x0010 /* 155 MBit single mode laser */ 1327 #define FE_UTP_OPTION 0x0020 /* 155 MBit UTP front end */ 1328 1329 #define NOVRAM_SIZE 64 1330 #define CMD_LEN 10 1331 1332 /*********** 1333 * 1334 * Switches and defines for header files. 1335 * 1336 * The following defines are used to turn on and off 1337 * various options in the header files. Primarily useful 1338 * for debugging. 1339 * 1340 ***********/ 1341 1342 /* 1343 * a list of the commands that can be sent to the NOVRAM 1344 */ 1345 1346 #define EXTEND 0x100 1347 #define IAWRITE 0x140 1348 #define IAREAD 0x180 1349 #define ERASE 0x1c0 1350 1351 #define EWDS 0x00 1352 #define WRAL 0x10 1353 #define ERAL 0x20 1354 #define EWEN 0x30 1355 1356 /* 1357 * these bits duplicate the hw_flip.h register settings 1358 * note: how the data in / out bits are defined in the flipper specification 1359 */ 1360 1361 #define NVCE 0x02 1362 #define NVSK 0x01 1363 #define NVDO 0x08 1364 #define NVDI 0x04 1365 /*********************** 1366 * 1367 * This define ands the value and the current config register and puts 1368 * the result in the config register 1369 * 1370 ***********************/ 1371 1372 #define CFG_AND(val) { \ 1373 u32 t; \ 1374 t = readl(iadev->reg+IPHASE5575_EEPROM_ACCESS); \ 1375 t &= (val); \ 1376 writel(t, iadev->reg+IPHASE5575_EEPROM_ACCESS); \ 1377 } 1378 1379 /*********************** 1380 * 1381 * This define ors the value and the current config register and puts 1382 * the result in the config register 1383 * 1384 ***********************/ 1385 1386 #define CFG_OR(val) { \ 1387 u32 t; \ 1388 t = readl(iadev->reg+IPHASE5575_EEPROM_ACCESS); \ 1389 t |= (val); \ 1390 writel(t, iadev->reg+IPHASE5575_EEPROM_ACCESS); \ 1391 } 1392 1393 /*********************** 1394 * 1395 * Send a command to the NOVRAM, the command is in cmd. 1396 * 1397 * clear CE and SK. Then assert CE. 1398 * Clock each of the command bits out in the correct order with SK 1399 * exit with CE still asserted 1400 * 1401 ***********************/ 1402 1403 #define NVRAM_CMD(cmd) { \ 1404 int i; \ 1405 u_short c = cmd; \ 1406 CFG_AND(~(NVCE|NVSK)); \ 1407 CFG_OR(NVCE); \ 1408 for (i=0; i<CMD_LEN; i++) { \ 1409 NVRAM_CLKOUT((c & (1 << (CMD_LEN - 1))) ? 1 : 0); \ 1410 c <<= 1; \ 1411 } \ 1412 } 1413 1414 /*********************** 1415 * 1416 * clear the CE, this must be used after each command is complete 1417 * 1418 ***********************/ 1419 1420 #define NVRAM_CLR_CE {CFG_AND(~NVCE)} 1421 1422 /*********************** 1423 * 1424 * clock the data bit in bitval out to the NOVRAM. The bitval must be 1425 * a 1 or 0, or the clockout operation is undefined 1426 * 1427 ***********************/ 1428 1429 #define NVRAM_CLKOUT(bitval) { \ 1430 CFG_AND(~NVDI); \ 1431 CFG_OR((bitval) ? NVDI : 0); \ 1432 CFG_OR(NVSK); \ 1433 CFG_AND( ~NVSK); \ 1434 } 1435 1436 /*********************** 1437 * 1438 * clock the data bit in and return a 1 or 0, depending on the value 1439 * that was received from the NOVRAM 1440 * 1441 ***********************/ 1442 1443 #define NVRAM_CLKIN(value) { \ 1444 u32 _t; \ 1445 CFG_OR(NVSK); \ 1446 CFG_AND(~NVSK); \ 1447 _t = readl(iadev->reg+IPHASE5575_EEPROM_ACCESS); \ 1448 value = (_t & NVDO) ? 1 : 0; \ 1449 } 1450 1451 1452 #endif /* IPHASE_H */ 1453