1 /* 2 * pata_sil680.c - SIL680 PATA for new ATA layer 3 * (C) 2005 Red Hat Inc 4 * 5 * based upon 6 * 7 * linux/drivers/ide/pci/siimage.c Version 1.07 Nov 30, 2003 8 * 9 * Copyright (C) 2001-2002 Andre Hedrick <andre@linux-ide.org> 10 * Copyright (C) 2003 Red Hat <alan@redhat.com> 11 * 12 * May be copied or modified under the terms of the GNU General Public License 13 * 14 * Documentation publically available. 15 * 16 * If you have strange problems with nVidia chipset systems please 17 * see the SI support documentation and update your system BIOS 18 * if necessary 19 * 20 * TODO 21 * If we know all our devices are LBA28 (or LBA28 sized) we could use 22 * the command fifo mode. 23 */ 24 25 #include <linux/kernel.h> 26 #include <linux/module.h> 27 #include <linux/pci.h> 28 #include <linux/init.h> 29 #include <linux/blkdev.h> 30 #include <linux/delay.h> 31 #include <scsi/scsi_host.h> 32 #include <linux/libata.h> 33 34 #define DRV_NAME "pata_sil680" 35 #define DRV_VERSION "0.4.9" 36 37 #define SIL680_MMIO_BAR 5 38 39 /** 40 * sil680_selreg - return register base 41 * @hwif: interface 42 * @r: config offset 43 * 44 * Turn a config register offset into the right address in either 45 * PCI space or MMIO space to access the control register in question 46 * Thankfully this is a configuration operation so isnt performance 47 * criticial. 48 */ 49 50 static unsigned long sil680_selreg(struct ata_port *ap, int r) 51 { 52 unsigned long base = 0xA0 + r; 53 base += (ap->port_no << 4); 54 return base; 55 } 56 57 /** 58 * sil680_seldev - return register base 59 * @hwif: interface 60 * @r: config offset 61 * 62 * Turn a config register offset into the right address in either 63 * PCI space or MMIO space to access the control register in question 64 * including accounting for the unit shift. 65 */ 66 67 static unsigned long sil680_seldev(struct ata_port *ap, struct ata_device *adev, int r) 68 { 69 unsigned long base = 0xA0 + r; 70 base += (ap->port_no << 4); 71 base |= adev->devno ? 2 : 0; 72 return base; 73 } 74 75 76 /** 77 * sil680_cable_detect - cable detection 78 * @ap: ATA port 79 * 80 * Perform cable detection. The SIL680 stores this in PCI config 81 * space for us. 82 */ 83 84 static int sil680_cable_detect(struct ata_port *ap) { 85 struct pci_dev *pdev = to_pci_dev(ap->host->dev); 86 unsigned long addr = sil680_selreg(ap, 0); 87 u8 ata66; 88 pci_read_config_byte(pdev, addr, &ata66); 89 if (ata66 & 1) 90 return ATA_CBL_PATA80; 91 else 92 return ATA_CBL_PATA40; 93 } 94 95 /** 96 * sil680_set_piomode - set initial PIO mode data 97 * @ap: ATA interface 98 * @adev: ATA device 99 * 100 * Program the SIL680 registers for PIO mode. Note that the task speed 101 * registers are shared between the devices so we must pick the lowest 102 * mode for command work. 103 */ 104 105 static void sil680_set_piomode(struct ata_port *ap, struct ata_device *adev) 106 { 107 static u16 speed_p[5] = { 0x328A, 0x2283, 0x1104, 0x10C3, 0x10C1 }; 108 static u16 speed_t[5] = { 0x328A, 0x2283, 0x1281, 0x10C3, 0x10C1 }; 109 110 unsigned long tfaddr = sil680_selreg(ap, 0x02); 111 unsigned long addr = sil680_seldev(ap, adev, 0x04); 112 unsigned long addr_mask = 0x80 + 4 * ap->port_no; 113 struct pci_dev *pdev = to_pci_dev(ap->host->dev); 114 int pio = adev->pio_mode - XFER_PIO_0; 115 int lowest_pio = pio; 116 int port_shift = 4 * adev->devno; 117 u16 reg; 118 u8 mode; 119 120 struct ata_device *pair = ata_dev_pair(adev); 121 122 if (pair != NULL && adev->pio_mode > pair->pio_mode) 123 lowest_pio = pair->pio_mode - XFER_PIO_0; 124 125 pci_write_config_word(pdev, addr, speed_p[pio]); 126 pci_write_config_word(pdev, tfaddr, speed_t[lowest_pio]); 127 128 pci_read_config_word(pdev, tfaddr-2, ®); 129 pci_read_config_byte(pdev, addr_mask, &mode); 130 131 reg &= ~0x0200; /* Clear IORDY */ 132 mode &= ~(3 << port_shift); /* Clear IORDY and DMA bits */ 133 134 if (ata_pio_need_iordy(adev)) { 135 reg |= 0x0200; /* Enable IORDY */ 136 mode |= 1 << port_shift; 137 } 138 pci_write_config_word(pdev, tfaddr-2, reg); 139 pci_write_config_byte(pdev, addr_mask, mode); 140 } 141 142 /** 143 * sil680_set_dmamode - set initial DMA mode data 144 * @ap: ATA interface 145 * @adev: ATA device 146 * 147 * Program the MWDMA/UDMA modes for the sil680 k 148 * chipset. The MWDMA mode values are pulled from a lookup table 149 * while the chipset uses mode number for UDMA. 150 */ 151 152 static void sil680_set_dmamode(struct ata_port *ap, struct ata_device *adev) 153 { 154 static u8 ultra_table[2][7] = { 155 { 0x0C, 0x07, 0x05, 0x04, 0x02, 0x01, 0xFF }, /* 100MHz */ 156 { 0x0F, 0x0B, 0x07, 0x05, 0x03, 0x02, 0x01 }, /* 133Mhz */ 157 }; 158 static u16 dma_table[3] = { 0x2208, 0x10C2, 0x10C1 }; 159 160 struct pci_dev *pdev = to_pci_dev(ap->host->dev); 161 unsigned long ma = sil680_seldev(ap, adev, 0x08); 162 unsigned long ua = sil680_seldev(ap, adev, 0x0C); 163 unsigned long addr_mask = 0x80 + 4 * ap->port_no; 164 int port_shift = adev->devno * 4; 165 u8 scsc, mode; 166 u16 multi, ultra; 167 168 pci_read_config_byte(pdev, 0x8A, &scsc); 169 pci_read_config_byte(pdev, addr_mask, &mode); 170 pci_read_config_word(pdev, ma, &multi); 171 pci_read_config_word(pdev, ua, &ultra); 172 173 /* Mask timing bits */ 174 ultra &= ~0x3F; 175 mode &= ~(0x03 << port_shift); 176 177 /* Extract scsc */ 178 scsc = (scsc & 0x30) ? 1: 0; 179 180 if (adev->dma_mode >= XFER_UDMA_0) { 181 multi = 0x10C1; 182 ultra |= ultra_table[scsc][adev->dma_mode - XFER_UDMA_0]; 183 mode |= (0x03 << port_shift); 184 } else { 185 multi = dma_table[adev->dma_mode - XFER_MW_DMA_0]; 186 mode |= (0x02 << port_shift); 187 } 188 pci_write_config_byte(pdev, addr_mask, mode); 189 pci_write_config_word(pdev, ma, multi); 190 pci_write_config_word(pdev, ua, ultra); 191 } 192 193 static struct scsi_host_template sil680_sht = { 194 ATA_BMDMA_SHT(DRV_NAME), 195 }; 196 197 static struct ata_port_operations sil680_port_ops = { 198 .inherits = &ata_bmdma32_port_ops, 199 .cable_detect = sil680_cable_detect, 200 .set_piomode = sil680_set_piomode, 201 .set_dmamode = sil680_set_dmamode, 202 }; 203 204 /** 205 * sil680_init_chip - chip setup 206 * @pdev: PCI device 207 * 208 * Perform all the chip setup which must be done both when the device 209 * is powered up on boot and when we resume in case we resumed from RAM. 210 * Returns the final clock settings. 211 */ 212 213 static u8 sil680_init_chip(struct pci_dev *pdev, int *try_mmio) 214 { 215 u8 tmpbyte = 0; 216 217 /* FIXME: double check */ 218 pci_write_config_byte(pdev, PCI_CACHE_LINE_SIZE, 219 pdev->revision ? 1 : 255); 220 221 pci_write_config_byte(pdev, 0x80, 0x00); 222 pci_write_config_byte(pdev, 0x84, 0x00); 223 224 pci_read_config_byte(pdev, 0x8A, &tmpbyte); 225 226 dev_dbg(&pdev->dev, "sil680: BA5_EN = %d clock = %02X\n", 227 tmpbyte & 1, tmpbyte & 0x30); 228 229 *try_mmio = 0; 230 #ifdef CONFIG_PPC 231 if (machine_is(cell)) 232 *try_mmio = (tmpbyte & 1) || pci_resource_start(pdev, 5); 233 #endif 234 235 switch(tmpbyte & 0x30) { 236 case 0x00: 237 /* 133 clock attempt to force it on */ 238 pci_write_config_byte(pdev, 0x8A, tmpbyte|0x10); 239 break; 240 case 0x30: 241 /* if clocking is disabled */ 242 /* 133 clock attempt to force it on */ 243 pci_write_config_byte(pdev, 0x8A, tmpbyte & ~0x20); 244 break; 245 case 0x10: 246 /* 133 already */ 247 break; 248 case 0x20: 249 /* BIOS set PCI x2 clocking */ 250 break; 251 } 252 253 pci_read_config_byte(pdev, 0x8A, &tmpbyte); 254 dev_dbg(&pdev->dev, "sil680: BA5_EN = %d clock = %02X\n", 255 tmpbyte & 1, tmpbyte & 0x30); 256 257 pci_write_config_byte(pdev, 0xA1, 0x72); 258 pci_write_config_word(pdev, 0xA2, 0x328A); 259 pci_write_config_dword(pdev, 0xA4, 0x62DD62DD); 260 pci_write_config_dword(pdev, 0xA8, 0x43924392); 261 pci_write_config_dword(pdev, 0xAC, 0x40094009); 262 pci_write_config_byte(pdev, 0xB1, 0x72); 263 pci_write_config_word(pdev, 0xB2, 0x328A); 264 pci_write_config_dword(pdev, 0xB4, 0x62DD62DD); 265 pci_write_config_dword(pdev, 0xB8, 0x43924392); 266 pci_write_config_dword(pdev, 0xBC, 0x40094009); 267 268 switch(tmpbyte & 0x30) { 269 case 0x00: printk(KERN_INFO "sil680: 100MHz clock.\n");break; 270 case 0x10: printk(KERN_INFO "sil680: 133MHz clock.\n");break; 271 case 0x20: printk(KERN_INFO "sil680: Using PCI clock.\n");break; 272 /* This last case is _NOT_ ok */ 273 case 0x30: printk(KERN_ERR "sil680: Clock disabled ?\n"); 274 } 275 return tmpbyte & 0x30; 276 } 277 278 static int __devinit sil680_init_one(struct pci_dev *pdev, 279 const struct pci_device_id *id) 280 { 281 static const struct ata_port_info info = { 282 .flags = ATA_FLAG_SLAVE_POSS, 283 .pio_mask = ATA_PIO4, 284 .mwdma_mask = ATA_MWDMA2, 285 .udma_mask = ATA_UDMA6, 286 .port_ops = &sil680_port_ops 287 }; 288 static const struct ata_port_info info_slow = { 289 .flags = ATA_FLAG_SLAVE_POSS, 290 .pio_mask = ATA_PIO4, 291 .mwdma_mask = ATA_MWDMA2, 292 .udma_mask = ATA_UDMA5, 293 .port_ops = &sil680_port_ops 294 }; 295 const struct ata_port_info *ppi[] = { &info, NULL }; 296 static int printed_version; 297 struct ata_host *host; 298 void __iomem *mmio_base; 299 int rc, try_mmio; 300 301 if (!printed_version++) 302 dev_printk(KERN_DEBUG, &pdev->dev, "version " DRV_VERSION "\n"); 303 304 rc = pcim_enable_device(pdev); 305 if (rc) 306 return rc; 307 308 switch (sil680_init_chip(pdev, &try_mmio)) { 309 case 0: 310 ppi[0] = &info_slow; 311 break; 312 case 0x30: 313 return -ENODEV; 314 } 315 316 if (!try_mmio) 317 goto use_ioports; 318 319 /* Try to acquire MMIO resources and fallback to PIO if 320 * that fails 321 */ 322 rc = pcim_iomap_regions(pdev, 1 << SIL680_MMIO_BAR, DRV_NAME); 323 if (rc) 324 goto use_ioports; 325 326 /* Allocate host and set it up */ 327 host = ata_host_alloc_pinfo(&pdev->dev, ppi, 2); 328 if (!host) 329 return -ENOMEM; 330 host->iomap = pcim_iomap_table(pdev); 331 332 /* Setup DMA masks */ 333 rc = pci_set_dma_mask(pdev, ATA_DMA_MASK); 334 if (rc) 335 return rc; 336 rc = pci_set_consistent_dma_mask(pdev, ATA_DMA_MASK); 337 if (rc) 338 return rc; 339 pci_set_master(pdev); 340 341 /* Get MMIO base and initialize port addresses */ 342 mmio_base = host->iomap[SIL680_MMIO_BAR]; 343 host->ports[0]->ioaddr.bmdma_addr = mmio_base + 0x00; 344 host->ports[0]->ioaddr.cmd_addr = mmio_base + 0x80; 345 host->ports[0]->ioaddr.ctl_addr = mmio_base + 0x8a; 346 host->ports[0]->ioaddr.altstatus_addr = mmio_base + 0x8a; 347 ata_sff_std_ports(&host->ports[0]->ioaddr); 348 host->ports[1]->ioaddr.bmdma_addr = mmio_base + 0x08; 349 host->ports[1]->ioaddr.cmd_addr = mmio_base + 0xc0; 350 host->ports[1]->ioaddr.ctl_addr = mmio_base + 0xca; 351 host->ports[1]->ioaddr.altstatus_addr = mmio_base + 0xca; 352 ata_sff_std_ports(&host->ports[1]->ioaddr); 353 354 /* Register & activate */ 355 return ata_host_activate(host, pdev->irq, ata_sff_interrupt, 356 IRQF_SHARED, &sil680_sht); 357 358 use_ioports: 359 return ata_pci_sff_init_one(pdev, ppi, &sil680_sht, NULL); 360 } 361 362 #ifdef CONFIG_PM 363 static int sil680_reinit_one(struct pci_dev *pdev) 364 { 365 struct ata_host *host = dev_get_drvdata(&pdev->dev); 366 int try_mmio, rc; 367 368 rc = ata_pci_device_do_resume(pdev); 369 if (rc) 370 return rc; 371 sil680_init_chip(pdev, &try_mmio); 372 ata_host_resume(host); 373 return 0; 374 } 375 #endif 376 377 static const struct pci_device_id sil680[] = { 378 { PCI_VDEVICE(CMD, PCI_DEVICE_ID_SII_680), }, 379 380 { }, 381 }; 382 383 static struct pci_driver sil680_pci_driver = { 384 .name = DRV_NAME, 385 .id_table = sil680, 386 .probe = sil680_init_one, 387 .remove = ata_pci_remove_one, 388 #ifdef CONFIG_PM 389 .suspend = ata_pci_device_suspend, 390 .resume = sil680_reinit_one, 391 #endif 392 }; 393 394 static int __init sil680_init(void) 395 { 396 return pci_register_driver(&sil680_pci_driver); 397 } 398 399 static void __exit sil680_exit(void) 400 { 401 pci_unregister_driver(&sil680_pci_driver); 402 } 403 404 MODULE_AUTHOR("Alan Cox"); 405 MODULE_DESCRIPTION("low-level driver for SI680 PATA"); 406 MODULE_LICENSE("GPL"); 407 MODULE_DEVICE_TABLE(pci, sil680); 408 MODULE_VERSION(DRV_VERSION); 409 410 module_init(sil680_init); 411 module_exit(sil680_exit); 412