1 /* 2 * pata_rdc - Driver for later RDC PATA controllers 3 * 4 * This is actually a driver for hardware meeting 5 * INCITS 370-2004 (1510D): ATA Host Adapter Standards 6 * 7 * Based on ata_piix. 8 * 9 * This program is free software; you can redistribute it and/or modify 10 * it under the terms of the GNU General Public License as published by 11 * the Free Software Foundation; either version 2, or (at your option) 12 * any later version. 13 * 14 * This program is distributed in the hope that it will be useful, 15 * but WITHOUT ANY WARRANTY; without even the implied warranty of 16 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the 17 * GNU General Public License for more details. 18 * 19 * You should have received a copy of the GNU General Public License 20 * along with this program; see the file COPYING. If not, write to 21 * the Free Software Foundation, 675 Mass Ave, Cambridge, MA 02139, USA. 22 */ 23 24 #include <linux/kernel.h> 25 #include <linux/module.h> 26 #include <linux/pci.h> 27 #include <linux/blkdev.h> 28 #include <linux/delay.h> 29 #include <linux/device.h> 30 #include <linux/gfp.h> 31 #include <scsi/scsi_host.h> 32 #include <linux/libata.h> 33 #include <linux/dmi.h> 34 35 #define DRV_NAME "pata_rdc" 36 #define DRV_VERSION "0.01" 37 38 struct rdc_host_priv { 39 u32 saved_iocfg; 40 }; 41 42 /** 43 * rdc_pata_cable_detect - Probe host controller cable detect info 44 * @ap: Port for which cable detect info is desired 45 * 46 * Read 80c cable indicator from ATA PCI device's PCI config 47 * register. This register is normally set by firmware (BIOS). 48 * 49 * LOCKING: 50 * None (inherited from caller). 51 */ 52 53 static int rdc_pata_cable_detect(struct ata_port *ap) 54 { 55 struct rdc_host_priv *hpriv = ap->host->private_data; 56 u8 mask; 57 58 /* check BIOS cable detect results */ 59 mask = 0x30 << (2 * ap->port_no); 60 if ((hpriv->saved_iocfg & mask) == 0) 61 return ATA_CBL_PATA40; 62 return ATA_CBL_PATA80; 63 } 64 65 /** 66 * rdc_pata_prereset - prereset for PATA host controller 67 * @link: Target link 68 * @deadline: deadline jiffies for the operation 69 * 70 * LOCKING: 71 * None (inherited from caller). 72 */ 73 static int rdc_pata_prereset(struct ata_link *link, unsigned long deadline) 74 { 75 struct ata_port *ap = link->ap; 76 struct pci_dev *pdev = to_pci_dev(ap->host->dev); 77 78 static const struct pci_bits rdc_enable_bits[] = { 79 { 0x41U, 1U, 0x80UL, 0x80UL }, /* port 0 */ 80 { 0x43U, 1U, 0x80UL, 0x80UL }, /* port 1 */ 81 }; 82 83 if (!pci_test_config_bits(pdev, &rdc_enable_bits[ap->port_no])) 84 return -ENOENT; 85 return ata_sff_prereset(link, deadline); 86 } 87 88 static DEFINE_SPINLOCK(rdc_lock); 89 90 /** 91 * rdc_set_piomode - Initialize host controller PATA PIO timings 92 * @ap: Port whose timings we are configuring 93 * @adev: um 94 * 95 * Set PIO mode for device, in host controller PCI config space. 96 * 97 * LOCKING: 98 * None (inherited from caller). 99 */ 100 101 static void rdc_set_piomode(struct ata_port *ap, struct ata_device *adev) 102 { 103 unsigned int pio = adev->pio_mode - XFER_PIO_0; 104 struct pci_dev *dev = to_pci_dev(ap->host->dev); 105 unsigned long flags; 106 unsigned int is_slave = (adev->devno != 0); 107 unsigned int master_port= ap->port_no ? 0x42 : 0x40; 108 unsigned int slave_port = 0x44; 109 u16 master_data; 110 u8 slave_data; 111 u8 udma_enable; 112 int control = 0; 113 114 static const /* ISP RTC */ 115 u8 timings[][2] = { { 0, 0 }, 116 { 0, 0 }, 117 { 1, 0 }, 118 { 2, 1 }, 119 { 2, 3 }, }; 120 121 if (pio >= 2) 122 control |= 1; /* TIME1 enable */ 123 if (ata_pio_need_iordy(adev)) 124 control |= 2; /* IE enable */ 125 126 if (adev->class == ATA_DEV_ATA) 127 control |= 4; /* PPE enable */ 128 129 spin_lock_irqsave(&rdc_lock, flags); 130 131 /* PIO configuration clears DTE unconditionally. It will be 132 * programmed in set_dmamode which is guaranteed to be called 133 * after set_piomode if any DMA mode is available. 134 */ 135 pci_read_config_word(dev, master_port, &master_data); 136 if (is_slave) { 137 /* clear TIME1|IE1|PPE1|DTE1 */ 138 master_data &= 0xff0f; 139 /* Enable SITRE (separate slave timing register) */ 140 master_data |= 0x4000; 141 /* enable PPE1, IE1 and TIME1 as needed */ 142 master_data |= (control << 4); 143 pci_read_config_byte(dev, slave_port, &slave_data); 144 slave_data &= (ap->port_no ? 0x0f : 0xf0); 145 /* Load the timing nibble for this slave */ 146 slave_data |= ((timings[pio][0] << 2) | timings[pio][1]) 147 << (ap->port_no ? 4 : 0); 148 } else { 149 /* clear ISP|RCT|TIME0|IE0|PPE0|DTE0 */ 150 master_data &= 0xccf0; 151 /* Enable PPE, IE and TIME as appropriate */ 152 master_data |= control; 153 /* load ISP and RCT */ 154 master_data |= 155 (timings[pio][0] << 12) | 156 (timings[pio][1] << 8); 157 } 158 pci_write_config_word(dev, master_port, master_data); 159 if (is_slave) 160 pci_write_config_byte(dev, slave_port, slave_data); 161 162 /* Ensure the UDMA bit is off - it will be turned back on if 163 UDMA is selected */ 164 165 pci_read_config_byte(dev, 0x48, &udma_enable); 166 udma_enable &= ~(1 << (2 * ap->port_no + adev->devno)); 167 pci_write_config_byte(dev, 0x48, udma_enable); 168 169 spin_unlock_irqrestore(&rdc_lock, flags); 170 } 171 172 /** 173 * rdc_set_dmamode - Initialize host controller PATA PIO timings 174 * @ap: Port whose timings we are configuring 175 * @adev: Drive in question 176 * 177 * Set UDMA mode for device, in host controller PCI config space. 178 * 179 * LOCKING: 180 * None (inherited from caller). 181 */ 182 183 static void rdc_set_dmamode(struct ata_port *ap, struct ata_device *adev) 184 { 185 struct pci_dev *dev = to_pci_dev(ap->host->dev); 186 unsigned long flags; 187 u8 master_port = ap->port_no ? 0x42 : 0x40; 188 u16 master_data; 189 u8 speed = adev->dma_mode; 190 int devid = adev->devno + 2 * ap->port_no; 191 u8 udma_enable = 0; 192 193 static const /* ISP RTC */ 194 u8 timings[][2] = { { 0, 0 }, 195 { 0, 0 }, 196 { 1, 0 }, 197 { 2, 1 }, 198 { 2, 3 }, }; 199 200 spin_lock_irqsave(&rdc_lock, flags); 201 202 pci_read_config_word(dev, master_port, &master_data); 203 pci_read_config_byte(dev, 0x48, &udma_enable); 204 205 if (speed >= XFER_UDMA_0) { 206 unsigned int udma = adev->dma_mode - XFER_UDMA_0; 207 u16 udma_timing; 208 u16 ideconf; 209 int u_clock, u_speed; 210 211 /* 212 * UDMA is handled by a combination of clock switching and 213 * selection of dividers 214 * 215 * Handy rule: Odd modes are UDMATIMx 01, even are 02 216 * except UDMA0 which is 00 217 */ 218 u_speed = min(2 - (udma & 1), udma); 219 if (udma == 5) 220 u_clock = 0x1000; /* 100Mhz */ 221 else if (udma > 2) 222 u_clock = 1; /* 66Mhz */ 223 else 224 u_clock = 0; /* 33Mhz */ 225 226 udma_enable |= (1 << devid); 227 228 /* Load the CT/RP selection */ 229 pci_read_config_word(dev, 0x4A, &udma_timing); 230 udma_timing &= ~(3 << (4 * devid)); 231 udma_timing |= u_speed << (4 * devid); 232 pci_write_config_word(dev, 0x4A, udma_timing); 233 234 /* Select a 33/66/100Mhz clock */ 235 pci_read_config_word(dev, 0x54, &ideconf); 236 ideconf &= ~(0x1001 << devid); 237 ideconf |= u_clock << devid; 238 pci_write_config_word(dev, 0x54, ideconf); 239 } else { 240 /* 241 * MWDMA is driven by the PIO timings. We must also enable 242 * IORDY unconditionally along with TIME1. PPE has already 243 * been set when the PIO timing was set. 244 */ 245 unsigned int mwdma = adev->dma_mode - XFER_MW_DMA_0; 246 unsigned int control; 247 u8 slave_data; 248 const unsigned int needed_pio[3] = { 249 XFER_PIO_0, XFER_PIO_3, XFER_PIO_4 250 }; 251 int pio = needed_pio[mwdma] - XFER_PIO_0; 252 253 control = 3; /* IORDY|TIME1 */ 254 255 /* If the drive MWDMA is faster than it can do PIO then 256 we must force PIO into PIO0 */ 257 258 if (adev->pio_mode < needed_pio[mwdma]) 259 /* Enable DMA timing only */ 260 control |= 8; /* PIO cycles in PIO0 */ 261 262 if (adev->devno) { /* Slave */ 263 master_data &= 0xFF4F; /* Mask out IORDY|TIME1|DMAONLY */ 264 master_data |= control << 4; 265 pci_read_config_byte(dev, 0x44, &slave_data); 266 slave_data &= (ap->port_no ? 0x0f : 0xf0); 267 /* Load the matching timing */ 268 slave_data |= ((timings[pio][0] << 2) | timings[pio][1]) << (ap->port_no ? 4 : 0); 269 pci_write_config_byte(dev, 0x44, slave_data); 270 } else { /* Master */ 271 master_data &= 0xCCF4; /* Mask out IORDY|TIME1|DMAONLY 272 and master timing bits */ 273 master_data |= control; 274 master_data |= 275 (timings[pio][0] << 12) | 276 (timings[pio][1] << 8); 277 } 278 279 udma_enable &= ~(1 << devid); 280 pci_write_config_word(dev, master_port, master_data); 281 } 282 pci_write_config_byte(dev, 0x48, udma_enable); 283 284 spin_unlock_irqrestore(&rdc_lock, flags); 285 } 286 287 static struct ata_port_operations rdc_pata_ops = { 288 .inherits = &ata_bmdma32_port_ops, 289 .cable_detect = rdc_pata_cable_detect, 290 .set_piomode = rdc_set_piomode, 291 .set_dmamode = rdc_set_dmamode, 292 .prereset = rdc_pata_prereset, 293 }; 294 295 static const struct ata_port_info rdc_port_info = { 296 297 .flags = ATA_FLAG_SLAVE_POSS, 298 .pio_mask = ATA_PIO4, 299 .mwdma_mask = ATA_MWDMA12_ONLY, 300 .udma_mask = ATA_UDMA5, 301 .port_ops = &rdc_pata_ops, 302 }; 303 304 static struct scsi_host_template rdc_sht = { 305 ATA_BMDMA_SHT(DRV_NAME), 306 }; 307 308 /** 309 * rdc_init_one - Register PIIX ATA PCI device with kernel services 310 * @pdev: PCI device to register 311 * @ent: Entry in rdc_pci_tbl matching with @pdev 312 * 313 * Called from kernel PCI layer. We probe for combined mode (sigh), 314 * and then hand over control to libata, for it to do the rest. 315 * 316 * LOCKING: 317 * Inherited from PCI layer (may sleep). 318 * 319 * RETURNS: 320 * Zero on success, or -ERRNO value. 321 */ 322 323 static int rdc_init_one(struct pci_dev *pdev, const struct pci_device_id *ent) 324 { 325 struct device *dev = &pdev->dev; 326 struct ata_port_info port_info[2]; 327 const struct ata_port_info *ppi[] = { &port_info[0], &port_info[1] }; 328 struct ata_host *host; 329 struct rdc_host_priv *hpriv; 330 int rc; 331 332 ata_print_version_once(&pdev->dev, DRV_VERSION); 333 334 port_info[0] = rdc_port_info; 335 port_info[1] = rdc_port_info; 336 337 /* enable device and prepare host */ 338 rc = pcim_enable_device(pdev); 339 if (rc) 340 return rc; 341 342 hpriv = devm_kzalloc(dev, sizeof(*hpriv), GFP_KERNEL); 343 if (!hpriv) 344 return -ENOMEM; 345 346 /* Save IOCFG, this will be used for cable detection, quirk 347 * detection and restoration on detach. 348 */ 349 pci_read_config_dword(pdev, 0x54, &hpriv->saved_iocfg); 350 351 rc = ata_pci_bmdma_prepare_host(pdev, ppi, &host); 352 if (rc) 353 return rc; 354 host->private_data = hpriv; 355 356 pci_intx(pdev, 1); 357 358 host->flags |= ATA_HOST_PARALLEL_SCAN; 359 360 pci_set_master(pdev); 361 return ata_pci_sff_activate_host(host, ata_bmdma_interrupt, &rdc_sht); 362 } 363 364 static void rdc_remove_one(struct pci_dev *pdev) 365 { 366 struct ata_host *host = pci_get_drvdata(pdev); 367 struct rdc_host_priv *hpriv = host->private_data; 368 369 pci_write_config_dword(pdev, 0x54, hpriv->saved_iocfg); 370 371 ata_pci_remove_one(pdev); 372 } 373 374 static const struct pci_device_id rdc_pci_tbl[] = { 375 { PCI_DEVICE(0x17F3, 0x1011), }, 376 { PCI_DEVICE(0x17F3, 0x1012), }, 377 { } /* terminate list */ 378 }; 379 380 static struct pci_driver rdc_pci_driver = { 381 .name = DRV_NAME, 382 .id_table = rdc_pci_tbl, 383 .probe = rdc_init_one, 384 .remove = rdc_remove_one, 385 #ifdef CONFIG_PM_SLEEP 386 .suspend = ata_pci_device_suspend, 387 .resume = ata_pci_device_resume, 388 #endif 389 }; 390 391 392 module_pci_driver(rdc_pci_driver); 393 394 MODULE_AUTHOR("Alan Cox (based on ata_piix)"); 395 MODULE_DESCRIPTION("SCSI low-level driver for RDC PATA controllers"); 396 MODULE_LICENSE("GPL"); 397 MODULE_DEVICE_TABLE(pci, rdc_pci_tbl); 398 MODULE_VERSION(DRV_VERSION); 399