1 // SPDX-License-Identifier: GPL-2.0-only 2 /* 3 * pata_radisys.c - Intel PATA/SATA controllers 4 * 5 * (C) 2006 Red Hat <alan@lxorguk.ukuu.org.uk> 6 * 7 * Some parts based on ata_piix.c by Jeff Garzik and others. 8 * 9 * A PIIX relative, this device has a single ATA channel and no 10 * slave timings, SITRE or PPE. In that sense it is a close relative 11 * of the original PIIX. It does however support UDMA 33/66 per channel 12 * although no other modes/timings. Also lacking is 32bit I/O on the ATA 13 * port. 14 */ 15 16 #include <linux/kernel.h> 17 #include <linux/module.h> 18 #include <linux/pci.h> 19 #include <linux/blkdev.h> 20 #include <linux/delay.h> 21 #include <linux/device.h> 22 #include <scsi/scsi_host.h> 23 #include <linux/libata.h> 24 #include <linux/ata.h> 25 26 #define DRV_NAME "pata_radisys" 27 #define DRV_VERSION "0.4.4" 28 29 /** 30 * radisys_set_piomode - Initialize host controller PATA PIO timings 31 * @ap: ATA port 32 * @adev: Device whose timings we are configuring 33 * 34 * Set PIO mode for device, in host controller PCI config space. 35 * 36 * LOCKING: 37 * None (inherited from caller). 38 */ 39 40 static void radisys_set_piomode (struct ata_port *ap, struct ata_device *adev) 41 { 42 unsigned int pio = adev->pio_mode - XFER_PIO_0; 43 struct pci_dev *dev = to_pci_dev(ap->host->dev); 44 u16 idetm_data; 45 int control = 0; 46 47 /* 48 * See Intel Document 298600-004 for the timing programing rules 49 * for PIIX/ICH. Note that the early PIIX does not have the slave 50 * timing port at 0x44. The Radisys is a relative of the PIIX 51 * but not the same so be careful. 52 */ 53 54 static const /* ISP RTC */ 55 u8 timings[][2] = { { 0, 0 }, /* Check me */ 56 { 0, 0 }, 57 { 1, 1 }, 58 { 2, 2 }, 59 { 3, 3 }, }; 60 61 if (pio > 0) 62 control |= 1; /* TIME1 enable */ 63 if (ata_pio_need_iordy(adev)) 64 control |= 2; /* IE IORDY */ 65 66 pci_read_config_word(dev, 0x40, &idetm_data); 67 68 /* Enable IE and TIME as appropriate. Clear the other 69 drive timing bits */ 70 idetm_data &= 0xCCCC; 71 idetm_data |= (control << (4 * adev->devno)); 72 idetm_data |= (timings[pio][0] << 12) | 73 (timings[pio][1] << 8); 74 pci_write_config_word(dev, 0x40, idetm_data); 75 76 /* Track which port is configured */ 77 ap->private_data = adev; 78 } 79 80 /** 81 * radisys_set_dmamode - Initialize host controller PATA DMA timings 82 * @ap: Port whose timings we are configuring 83 * @adev: Device to program 84 * 85 * Set MWDMA mode for device, in host controller PCI config space. 86 * 87 * LOCKING: 88 * None (inherited from caller). 89 */ 90 91 static void radisys_set_dmamode (struct ata_port *ap, struct ata_device *adev) 92 { 93 struct pci_dev *dev = to_pci_dev(ap->host->dev); 94 u16 idetm_data; 95 u8 udma_enable; 96 97 static const /* ISP RTC */ 98 u8 timings[][2] = { { 0, 0 }, 99 { 0, 0 }, 100 { 1, 1 }, 101 { 2, 2 }, 102 { 3, 3 }, }; 103 104 /* 105 * MWDMA is driven by the PIO timings. We must also enable 106 * IORDY unconditionally. 107 */ 108 109 pci_read_config_word(dev, 0x40, &idetm_data); 110 pci_read_config_byte(dev, 0x48, &udma_enable); 111 112 if (adev->dma_mode < XFER_UDMA_0) { 113 unsigned int mwdma = adev->dma_mode - XFER_MW_DMA_0; 114 const unsigned int needed_pio[3] = { 115 XFER_PIO_0, XFER_PIO_3, XFER_PIO_4 116 }; 117 int pio = needed_pio[mwdma] - XFER_PIO_0; 118 int control = 3; /* IORDY|TIME0 */ 119 120 /* If the drive MWDMA is faster than it can do PIO then 121 we must force PIO0 for PIO cycles. */ 122 123 if (adev->pio_mode < needed_pio[mwdma]) 124 control = 1; 125 126 /* Mask out the relevant control and timing bits we will load. Also 127 clear the other drive TIME register as a precaution */ 128 129 idetm_data &= 0xCCCC; 130 idetm_data |= control << (4 * adev->devno); 131 idetm_data |= (timings[pio][0] << 12) | (timings[pio][1] << 8); 132 133 udma_enable &= ~(1 << adev->devno); 134 } else { 135 u8 udma_mode; 136 137 /* UDMA66 on: UDMA 33 and 66 are switchable via register 0x4A */ 138 139 pci_read_config_byte(dev, 0x4A, &udma_mode); 140 141 if (adev->xfer_mode == XFER_UDMA_2) 142 udma_mode &= ~(2 << (adev->devno * 4)); 143 else /* UDMA 4 */ 144 udma_mode |= (2 << (adev->devno * 4)); 145 146 pci_write_config_byte(dev, 0x4A, udma_mode); 147 148 udma_enable |= (1 << adev->devno); 149 } 150 pci_write_config_word(dev, 0x40, idetm_data); 151 pci_write_config_byte(dev, 0x48, udma_enable); 152 153 /* Track which port is configured */ 154 ap->private_data = adev; 155 } 156 157 /** 158 * radisys_qc_issue - command issue 159 * @qc: command pending 160 * 161 * Called when the libata layer is about to issue a command. We wrap 162 * this interface so that we can load the correct ATA timings if 163 * necessary. Our logic also clears TIME0/TIME1 for the other device so 164 * that, even if we get this wrong, cycles to the other device will 165 * be made PIO0. 166 */ 167 168 static unsigned int radisys_qc_issue(struct ata_queued_cmd *qc) 169 { 170 struct ata_port *ap = qc->ap; 171 struct ata_device *adev = qc->dev; 172 173 if (adev != ap->private_data) { 174 /* UDMA timing is not shared */ 175 if (adev->dma_mode < XFER_UDMA_0) { 176 if (adev->dma_mode) 177 radisys_set_dmamode(ap, adev); 178 else if (adev->pio_mode) 179 radisys_set_piomode(ap, adev); 180 } 181 } 182 return ata_bmdma_qc_issue(qc); 183 } 184 185 186 static struct scsi_host_template radisys_sht = { 187 ATA_BMDMA_SHT(DRV_NAME), 188 }; 189 190 static struct ata_port_operations radisys_pata_ops = { 191 .inherits = &ata_bmdma_port_ops, 192 .qc_issue = radisys_qc_issue, 193 .cable_detect = ata_cable_unknown, 194 .set_piomode = radisys_set_piomode, 195 .set_dmamode = radisys_set_dmamode, 196 }; 197 198 199 /** 200 * radisys_init_one - Register PIIX ATA PCI device with kernel services 201 * @pdev: PCI device to register 202 * @ent: Entry in radisys_pci_tbl matching with @pdev 203 * 204 * Called from kernel PCI layer. We probe for combined mode (sigh), 205 * and then hand over control to libata, for it to do the rest. 206 * 207 * LOCKING: 208 * Inherited from PCI layer (may sleep). 209 * 210 * RETURNS: 211 * Zero on success, or -ERRNO value. 212 */ 213 214 static int radisys_init_one (struct pci_dev *pdev, const struct pci_device_id *ent) 215 { 216 static const struct ata_port_info info = { 217 .flags = ATA_FLAG_SLAVE_POSS, 218 .pio_mask = ATA_PIO4, 219 .mwdma_mask = ATA_MWDMA12_ONLY, 220 .udma_mask = ATA_UDMA24_ONLY, 221 .port_ops = &radisys_pata_ops, 222 }; 223 const struct ata_port_info *ppi[] = { &info, NULL }; 224 225 ata_print_version_once(&pdev->dev, DRV_VERSION); 226 227 return ata_pci_bmdma_init_one(pdev, ppi, &radisys_sht, NULL, 0); 228 } 229 230 static const struct pci_device_id radisys_pci_tbl[] = { 231 { PCI_VDEVICE(RADISYS, 0x8201), }, 232 233 { } /* terminate list */ 234 }; 235 236 static struct pci_driver radisys_pci_driver = { 237 .name = DRV_NAME, 238 .id_table = radisys_pci_tbl, 239 .probe = radisys_init_one, 240 .remove = ata_pci_remove_one, 241 #ifdef CONFIG_PM_SLEEP 242 .suspend = ata_pci_device_suspend, 243 .resume = ata_pci_device_resume, 244 #endif 245 }; 246 247 module_pci_driver(radisys_pci_driver); 248 249 MODULE_AUTHOR("Alan Cox"); 250 MODULE_DESCRIPTION("SCSI low-level driver for Radisys R82600 controllers"); 251 MODULE_LICENSE("GPL"); 252 MODULE_DEVICE_TABLE(pci, radisys_pci_tbl); 253 MODULE_VERSION(DRV_VERSION); 254