1 /* 2 * pata_pdc202xx_old.c - Promise PDC202xx PATA for new ATA layer 3 * (C) 2005 Red Hat Inc 4 * Alan Cox <alan@lxorguk.ukuu.org.uk> 5 * (C) 2007,2009,2010 Bartlomiej Zolnierkiewicz 6 * 7 * Based in part on linux/drivers/ide/pci/pdc202xx_old.c 8 * 9 * First cut with LBA48/ATAPI 10 * 11 * TODO: 12 * Channel interlock/reset on both required ? 13 */ 14 15 #include <linux/kernel.h> 16 #include <linux/module.h> 17 #include <linux/pci.h> 18 #include <linux/blkdev.h> 19 #include <linux/delay.h> 20 #include <scsi/scsi_host.h> 21 #include <linux/libata.h> 22 23 #define DRV_NAME "pata_pdc202xx_old" 24 #define DRV_VERSION "0.4.3" 25 26 static int pdc2026x_cable_detect(struct ata_port *ap) 27 { 28 struct pci_dev *pdev = to_pci_dev(ap->host->dev); 29 u16 cis; 30 31 pci_read_config_word(pdev, 0x50, &cis); 32 if (cis & (1 << (10 + ap->port_no))) 33 return ATA_CBL_PATA40; 34 return ATA_CBL_PATA80; 35 } 36 37 static void pdc202xx_exec_command(struct ata_port *ap, 38 const struct ata_taskfile *tf) 39 { 40 DPRINTK("ata%u: cmd 0x%X\n", ap->print_id, tf->command); 41 42 iowrite8(tf->command, ap->ioaddr.command_addr); 43 ndelay(400); 44 } 45 46 static bool pdc202xx_irq_check(struct ata_port *ap) 47 { 48 struct pci_dev *pdev = to_pci_dev(ap->host->dev); 49 unsigned long master = pci_resource_start(pdev, 4); 50 u8 sc1d = inb(master + 0x1d); 51 52 if (ap->port_no) { 53 /* 54 * bit 7: error, bit 6: interrupting, 55 * bit 5: FIFO full, bit 4: FIFO empty 56 */ 57 return sc1d & 0x40; 58 } else { 59 /* 60 * bit 3: error, bit 2: interrupting, 61 * bit 1: FIFO full, bit 0: FIFO empty 62 */ 63 return sc1d & 0x04; 64 } 65 } 66 67 /** 68 * pdc202xx_configure_piomode - set chip PIO timing 69 * @ap: ATA interface 70 * @adev: ATA device 71 * @pio: PIO mode 72 * 73 * Called to do the PIO mode setup. Our timing registers are shared 74 * so a configure_dmamode call will undo any work we do here and vice 75 * versa 76 */ 77 78 static void pdc202xx_configure_piomode(struct ata_port *ap, struct ata_device *adev, int pio) 79 { 80 struct pci_dev *pdev = to_pci_dev(ap->host->dev); 81 int port = 0x60 + 8 * ap->port_no + 4 * adev->devno; 82 static u16 pio_timing[5] = { 83 0x0913, 0x050C , 0x0308, 0x0206, 0x0104 84 }; 85 u8 r_ap, r_bp; 86 87 pci_read_config_byte(pdev, port, &r_ap); 88 pci_read_config_byte(pdev, port + 1, &r_bp); 89 r_ap &= ~0x3F; /* Preserve ERRDY_EN, SYNC_IN */ 90 r_bp &= ~0x1F; 91 r_ap |= (pio_timing[pio] >> 8); 92 r_bp |= (pio_timing[pio] & 0xFF); 93 94 if (ata_pio_need_iordy(adev)) 95 r_ap |= 0x20; /* IORDY enable */ 96 if (adev->class == ATA_DEV_ATA) 97 r_ap |= 0x10; /* FIFO enable */ 98 pci_write_config_byte(pdev, port, r_ap); 99 pci_write_config_byte(pdev, port + 1, r_bp); 100 } 101 102 /** 103 * pdc202xx_set_piomode - set initial PIO mode data 104 * @ap: ATA interface 105 * @adev: ATA device 106 * 107 * Called to do the PIO mode setup. Our timing registers are shared 108 * but we want to set the PIO timing by default. 109 */ 110 111 static void pdc202xx_set_piomode(struct ata_port *ap, struct ata_device *adev) 112 { 113 pdc202xx_configure_piomode(ap, adev, adev->pio_mode - XFER_PIO_0); 114 } 115 116 /** 117 * pdc202xx_configure_dmamode - set DMA mode in chip 118 * @ap: ATA interface 119 * @adev: ATA device 120 * 121 * Load DMA cycle times into the chip ready for a DMA transfer 122 * to occur. 123 */ 124 125 static void pdc202xx_set_dmamode(struct ata_port *ap, struct ata_device *adev) 126 { 127 struct pci_dev *pdev = to_pci_dev(ap->host->dev); 128 int port = 0x60 + 8 * ap->port_no + 4 * adev->devno; 129 static u8 udma_timing[6][2] = { 130 { 0x60, 0x03 }, /* 33 Mhz Clock */ 131 { 0x40, 0x02 }, 132 { 0x20, 0x01 }, 133 { 0x40, 0x02 }, /* 66 Mhz Clock */ 134 { 0x20, 0x01 }, 135 { 0x20, 0x01 } 136 }; 137 static u8 mdma_timing[3][2] = { 138 { 0xe0, 0x0f }, 139 { 0x60, 0x04 }, 140 { 0x60, 0x03 }, 141 }; 142 u8 r_bp, r_cp; 143 144 pci_read_config_byte(pdev, port + 1, &r_bp); 145 pci_read_config_byte(pdev, port + 2, &r_cp); 146 147 r_bp &= ~0xE0; 148 r_cp &= ~0x0F; 149 150 if (adev->dma_mode >= XFER_UDMA_0) { 151 int speed = adev->dma_mode - XFER_UDMA_0; 152 r_bp |= udma_timing[speed][0]; 153 r_cp |= udma_timing[speed][1]; 154 155 } else { 156 int speed = adev->dma_mode - XFER_MW_DMA_0; 157 r_bp |= mdma_timing[speed][0]; 158 r_cp |= mdma_timing[speed][1]; 159 } 160 pci_write_config_byte(pdev, port + 1, r_bp); 161 pci_write_config_byte(pdev, port + 2, r_cp); 162 163 } 164 165 /** 166 * pdc2026x_bmdma_start - DMA engine begin 167 * @qc: ATA command 168 * 169 * In UDMA3 or higher we have to clock switch for the duration of the 170 * DMA transfer sequence. 171 * 172 * Note: The host lock held by the libata layer protects 173 * us from two channels both trying to set DMA bits at once 174 */ 175 176 static void pdc2026x_bmdma_start(struct ata_queued_cmd *qc) 177 { 178 struct ata_port *ap = qc->ap; 179 struct ata_device *adev = qc->dev; 180 struct ata_taskfile *tf = &qc->tf; 181 int sel66 = ap->port_no ? 0x08: 0x02; 182 183 void __iomem *master = ap->host->ports[0]->ioaddr.bmdma_addr; 184 void __iomem *clock = master + 0x11; 185 void __iomem *atapi_reg = master + 0x20 + (4 * ap->port_no); 186 187 u32 len; 188 189 /* Check we keep host level locking here */ 190 if (adev->dma_mode > XFER_UDMA_2) 191 iowrite8(ioread8(clock) | sel66, clock); 192 else 193 iowrite8(ioread8(clock) & ~sel66, clock); 194 195 /* The DMA clocks may have been trashed by a reset. FIXME: make conditional 196 and move to qc_issue ? */ 197 pdc202xx_set_dmamode(ap, qc->dev); 198 199 /* Cases the state machine will not complete correctly without help */ 200 if ((tf->flags & ATA_TFLAG_LBA48) || tf->protocol == ATAPI_PROT_DMA) { 201 len = qc->nbytes / 2; 202 203 if (tf->flags & ATA_TFLAG_WRITE) 204 len |= 0x06000000; 205 else 206 len |= 0x05000000; 207 208 iowrite32(len, atapi_reg); 209 } 210 211 /* Activate DMA */ 212 ata_bmdma_start(qc); 213 } 214 215 /** 216 * pdc2026x_bmdma_end - DMA engine stop 217 * @qc: ATA command 218 * 219 * After a DMA completes we need to put the clock back to 33MHz for 220 * PIO timings. 221 * 222 * Note: The host lock held by the libata layer protects 223 * us from two channels both trying to set DMA bits at once 224 */ 225 226 static void pdc2026x_bmdma_stop(struct ata_queued_cmd *qc) 227 { 228 struct ata_port *ap = qc->ap; 229 struct ata_device *adev = qc->dev; 230 struct ata_taskfile *tf = &qc->tf; 231 232 int sel66 = ap->port_no ? 0x08: 0x02; 233 /* The clock bits are in the same register for both channels */ 234 void __iomem *master = ap->host->ports[0]->ioaddr.bmdma_addr; 235 void __iomem *clock = master + 0x11; 236 void __iomem *atapi_reg = master + 0x20 + (4 * ap->port_no); 237 238 /* Cases the state machine will not complete correctly */ 239 if (tf->protocol == ATAPI_PROT_DMA || (tf->flags & ATA_TFLAG_LBA48)) { 240 iowrite32(0, atapi_reg); 241 iowrite8(ioread8(clock) & ~sel66, clock); 242 } 243 /* Flip back to 33Mhz for PIO */ 244 if (adev->dma_mode > XFER_UDMA_2) 245 iowrite8(ioread8(clock) & ~sel66, clock); 246 ata_bmdma_stop(qc); 247 pdc202xx_set_piomode(ap, adev); 248 } 249 250 /** 251 * pdc2026x_dev_config - device setup hook 252 * @adev: newly found device 253 * 254 * Perform chip specific early setup. We need to lock the transfer 255 * sizes to 8bit to avoid making the state engine on the 2026x cards 256 * barf. 257 */ 258 259 static void pdc2026x_dev_config(struct ata_device *adev) 260 { 261 adev->max_sectors = 256; 262 } 263 264 static int pdc2026x_port_start(struct ata_port *ap) 265 { 266 void __iomem *bmdma = ap->ioaddr.bmdma_addr; 267 if (bmdma) { 268 /* Enable burst mode */ 269 u8 burst = ioread8(bmdma + 0x1f); 270 iowrite8(burst | 0x01, bmdma + 0x1f); 271 } 272 return ata_bmdma_port_start(ap); 273 } 274 275 /** 276 * pdc2026x_check_atapi_dma - Check whether ATAPI DMA can be supported for this command 277 * @qc: Metadata associated with taskfile to check 278 * 279 * Just say no - not supported on older Promise. 280 * 281 * LOCKING: 282 * None (inherited from caller). 283 * 284 * RETURNS: 0 when ATAPI DMA can be used 285 * 1 otherwise 286 */ 287 288 static int pdc2026x_check_atapi_dma(struct ata_queued_cmd *qc) 289 { 290 return 1; 291 } 292 293 static struct scsi_host_template pdc202xx_sht = { 294 ATA_BMDMA_SHT(DRV_NAME), 295 }; 296 297 static struct ata_port_operations pdc2024x_port_ops = { 298 .inherits = &ata_bmdma_port_ops, 299 300 .cable_detect = ata_cable_40wire, 301 .set_piomode = pdc202xx_set_piomode, 302 .set_dmamode = pdc202xx_set_dmamode, 303 304 .sff_exec_command = pdc202xx_exec_command, 305 .sff_irq_check = pdc202xx_irq_check, 306 }; 307 308 static struct ata_port_operations pdc2026x_port_ops = { 309 .inherits = &pdc2024x_port_ops, 310 311 .check_atapi_dma = pdc2026x_check_atapi_dma, 312 .bmdma_start = pdc2026x_bmdma_start, 313 .bmdma_stop = pdc2026x_bmdma_stop, 314 315 .cable_detect = pdc2026x_cable_detect, 316 .dev_config = pdc2026x_dev_config, 317 318 .port_start = pdc2026x_port_start, 319 320 .sff_exec_command = pdc202xx_exec_command, 321 .sff_irq_check = pdc202xx_irq_check, 322 }; 323 324 static int pdc202xx_init_one(struct pci_dev *dev, const struct pci_device_id *id) 325 { 326 static const struct ata_port_info info[3] = { 327 { 328 .flags = ATA_FLAG_SLAVE_POSS, 329 .pio_mask = ATA_PIO4, 330 .mwdma_mask = ATA_MWDMA2, 331 .udma_mask = ATA_UDMA2, 332 .port_ops = &pdc2024x_port_ops 333 }, 334 { 335 .flags = ATA_FLAG_SLAVE_POSS, 336 .pio_mask = ATA_PIO4, 337 .mwdma_mask = ATA_MWDMA2, 338 .udma_mask = ATA_UDMA4, 339 .port_ops = &pdc2026x_port_ops 340 }, 341 { 342 .flags = ATA_FLAG_SLAVE_POSS, 343 .pio_mask = ATA_PIO4, 344 .mwdma_mask = ATA_MWDMA2, 345 .udma_mask = ATA_UDMA5, 346 .port_ops = &pdc2026x_port_ops 347 } 348 349 }; 350 const struct ata_port_info *ppi[] = { &info[id->driver_data], NULL }; 351 352 if (dev->device == PCI_DEVICE_ID_PROMISE_20265) { 353 struct pci_dev *bridge = dev->bus->self; 354 /* Don't grab anything behind a Promise I2O RAID */ 355 if (bridge && bridge->vendor == PCI_VENDOR_ID_INTEL) { 356 if (bridge->device == PCI_DEVICE_ID_INTEL_I960) 357 return -ENODEV; 358 if (bridge->device == PCI_DEVICE_ID_INTEL_I960RM) 359 return -ENODEV; 360 } 361 } 362 return ata_pci_bmdma_init_one(dev, ppi, &pdc202xx_sht, NULL, 0); 363 } 364 365 static const struct pci_device_id pdc202xx[] = { 366 { PCI_VDEVICE(PROMISE, PCI_DEVICE_ID_PROMISE_20246), 0 }, 367 { PCI_VDEVICE(PROMISE, PCI_DEVICE_ID_PROMISE_20262), 1 }, 368 { PCI_VDEVICE(PROMISE, PCI_DEVICE_ID_PROMISE_20263), 1 }, 369 { PCI_VDEVICE(PROMISE, PCI_DEVICE_ID_PROMISE_20265), 2 }, 370 { PCI_VDEVICE(PROMISE, PCI_DEVICE_ID_PROMISE_20267), 2 }, 371 372 { }, 373 }; 374 375 static struct pci_driver pdc202xx_pci_driver = { 376 .name = DRV_NAME, 377 .id_table = pdc202xx, 378 .probe = pdc202xx_init_one, 379 .remove = ata_pci_remove_one, 380 #ifdef CONFIG_PM_SLEEP 381 .suspend = ata_pci_device_suspend, 382 .resume = ata_pci_device_resume, 383 #endif 384 }; 385 386 module_pci_driver(pdc202xx_pci_driver); 387 388 MODULE_AUTHOR("Alan Cox"); 389 MODULE_DESCRIPTION("low-level driver for Promise 2024x and 20262-20267"); 390 MODULE_LICENSE("GPL"); 391 MODULE_DEVICE_TABLE(pci, pdc202xx); 392 MODULE_VERSION(DRV_VERSION); 393