1 // SPDX-License-Identifier: GPL-2.0-or-later 2 /* 3 * Promise PATA TX2/TX4/TX2000/133 IDE driver for pdc20268 to pdc20277. 4 * 5 * Ported to libata by: 6 * Albert Lee <albertcc@tw.ibm.com> IBM Corporation 7 * 8 * Copyright (C) 1998-2002 Andre Hedrick <andre@linux-ide.org> 9 * Portions Copyright (C) 1999 Promise Technology, Inc. 10 * 11 * Author: Frank Tiernan (frankt@promise.com) 12 * Released under terms of General Public License 13 * 14 * libata documentation is available via 'make {ps|pdf}docs', 15 * as Documentation/driver-api/libata.rst 16 * 17 * Hardware information only available under NDA. 18 */ 19 #include <linux/kernel.h> 20 #include <linux/module.h> 21 #include <linux/pci.h> 22 #include <linux/blkdev.h> 23 #include <linux/delay.h> 24 #include <linux/device.h> 25 #include <linux/ktime.h> 26 #include <scsi/scsi.h> 27 #include <scsi/scsi_host.h> 28 #include <scsi/scsi_cmnd.h> 29 #include <linux/libata.h> 30 31 #define DRV_NAME "pata_pdc2027x" 32 #define DRV_VERSION "1.0" 33 34 enum { 35 PDC_MMIO_BAR = 5, 36 37 PDC_UDMA_100 = 0, 38 PDC_UDMA_133 = 1, 39 40 PDC_100_MHZ = 100000000, 41 PDC_133_MHZ = 133333333, 42 43 PDC_SYS_CTL = 0x1100, 44 PDC_ATA_CTL = 0x1104, 45 PDC_GLOBAL_CTL = 0x1108, 46 PDC_CTCR0 = 0x110C, 47 PDC_CTCR1 = 0x1110, 48 PDC_BYTE_COUNT = 0x1120, 49 PDC_PLL_CTL = 0x1202, 50 }; 51 52 static int pdc2027x_init_one(struct pci_dev *pdev, const struct pci_device_id *ent); 53 #ifdef CONFIG_PM_SLEEP 54 static int pdc2027x_reinit_one(struct pci_dev *pdev); 55 #endif 56 static int pdc2027x_prereset(struct ata_link *link, unsigned long deadline); 57 static void pdc2027x_set_piomode(struct ata_port *ap, struct ata_device *adev); 58 static void pdc2027x_set_dmamode(struct ata_port *ap, struct ata_device *adev); 59 static int pdc2027x_check_atapi_dma(struct ata_queued_cmd *qc); 60 static unsigned int pdc2027x_mode_filter(struct ata_device *adev, unsigned int mask); 61 static int pdc2027x_cable_detect(struct ata_port *ap); 62 static int pdc2027x_set_mode(struct ata_link *link, struct ata_device **r_failed); 63 64 /* 65 * ATA Timing Tables based on 133MHz controller clock. 66 * These tables are only used when the controller is in 133MHz clock. 67 * If the controller is in 100MHz clock, the ASIC hardware will 68 * set the timing registers automatically when "set feature" command 69 * is issued to the device. However, if the controller clock is 133MHz, 70 * the following tables must be used. 71 */ 72 static const struct pdc2027x_pio_timing { 73 u8 value0, value1, value2; 74 } pdc2027x_pio_timing_tbl[] = { 75 { 0xfb, 0x2b, 0xac }, /* PIO mode 0 */ 76 { 0x46, 0x29, 0xa4 }, /* PIO mode 1 */ 77 { 0x23, 0x26, 0x64 }, /* PIO mode 2 */ 78 { 0x27, 0x0d, 0x35 }, /* PIO mode 3, IORDY on, Prefetch off */ 79 { 0x23, 0x09, 0x25 }, /* PIO mode 4, IORDY on, Prefetch off */ 80 }; 81 82 static const struct pdc2027x_mdma_timing { 83 u8 value0, value1; 84 } pdc2027x_mdma_timing_tbl[] = { 85 { 0xdf, 0x5f }, /* MDMA mode 0 */ 86 { 0x6b, 0x27 }, /* MDMA mode 1 */ 87 { 0x69, 0x25 }, /* MDMA mode 2 */ 88 }; 89 90 static const struct pdc2027x_udma_timing { 91 u8 value0, value1, value2; 92 } pdc2027x_udma_timing_tbl[] = { 93 { 0x4a, 0x0f, 0xd5 }, /* UDMA mode 0 */ 94 { 0x3a, 0x0a, 0xd0 }, /* UDMA mode 1 */ 95 { 0x2a, 0x07, 0xcd }, /* UDMA mode 2 */ 96 { 0x1a, 0x05, 0xcd }, /* UDMA mode 3 */ 97 { 0x1a, 0x03, 0xcd }, /* UDMA mode 4 */ 98 { 0x1a, 0x02, 0xcb }, /* UDMA mode 5 */ 99 { 0x1a, 0x01, 0xcb }, /* UDMA mode 6 */ 100 }; 101 102 static const struct pci_device_id pdc2027x_pci_tbl[] = { 103 { PCI_VDEVICE(PROMISE, PCI_DEVICE_ID_PROMISE_20268), PDC_UDMA_100 }, 104 { PCI_VDEVICE(PROMISE, PCI_DEVICE_ID_PROMISE_20269), PDC_UDMA_133 }, 105 { PCI_VDEVICE(PROMISE, PCI_DEVICE_ID_PROMISE_20270), PDC_UDMA_100 }, 106 { PCI_VDEVICE(PROMISE, PCI_DEVICE_ID_PROMISE_20271), PDC_UDMA_133 }, 107 { PCI_VDEVICE(PROMISE, PCI_DEVICE_ID_PROMISE_20275), PDC_UDMA_133 }, 108 { PCI_VDEVICE(PROMISE, PCI_DEVICE_ID_PROMISE_20276), PDC_UDMA_133 }, 109 { PCI_VDEVICE(PROMISE, PCI_DEVICE_ID_PROMISE_20277), PDC_UDMA_133 }, 110 111 { } /* terminate list */ 112 }; 113 114 static struct pci_driver pdc2027x_pci_driver = { 115 .name = DRV_NAME, 116 .id_table = pdc2027x_pci_tbl, 117 .probe = pdc2027x_init_one, 118 .remove = ata_pci_remove_one, 119 #ifdef CONFIG_PM_SLEEP 120 .suspend = ata_pci_device_suspend, 121 .resume = pdc2027x_reinit_one, 122 #endif 123 }; 124 125 static struct scsi_host_template pdc2027x_sht = { 126 ATA_BMDMA_SHT(DRV_NAME), 127 }; 128 129 static struct ata_port_operations pdc2027x_pata100_ops = { 130 .inherits = &ata_bmdma_port_ops, 131 .check_atapi_dma = pdc2027x_check_atapi_dma, 132 .cable_detect = pdc2027x_cable_detect, 133 .prereset = pdc2027x_prereset, 134 }; 135 136 static struct ata_port_operations pdc2027x_pata133_ops = { 137 .inherits = &pdc2027x_pata100_ops, 138 .mode_filter = pdc2027x_mode_filter, 139 .set_piomode = pdc2027x_set_piomode, 140 .set_dmamode = pdc2027x_set_dmamode, 141 .set_mode = pdc2027x_set_mode, 142 }; 143 144 static struct ata_port_info pdc2027x_port_info[] = { 145 /* PDC_UDMA_100 */ 146 { 147 .flags = ATA_FLAG_SLAVE_POSS, 148 .pio_mask = ATA_PIO4, 149 .mwdma_mask = ATA_MWDMA2, 150 .udma_mask = ATA_UDMA5, 151 .port_ops = &pdc2027x_pata100_ops, 152 }, 153 /* PDC_UDMA_133 */ 154 { 155 .flags = ATA_FLAG_SLAVE_POSS, 156 .pio_mask = ATA_PIO4, 157 .mwdma_mask = ATA_MWDMA2, 158 .udma_mask = ATA_UDMA6, 159 .port_ops = &pdc2027x_pata133_ops, 160 }, 161 }; 162 163 MODULE_AUTHOR("Andre Hedrick, Frank Tiernan, Albert Lee"); 164 MODULE_DESCRIPTION("libata driver module for Promise PDC20268 to PDC20277"); 165 MODULE_LICENSE("GPL"); 166 MODULE_VERSION(DRV_VERSION); 167 MODULE_DEVICE_TABLE(pci, pdc2027x_pci_tbl); 168 169 /** 170 * port_mmio - Get the MMIO address of PDC2027x extended registers 171 * @ap: Port 172 * @offset: offset from mmio base 173 */ 174 static inline void __iomem *port_mmio(struct ata_port *ap, unsigned int offset) 175 { 176 return ap->host->iomap[PDC_MMIO_BAR] + ap->port_no * 0x100 + offset; 177 } 178 179 /** 180 * dev_mmio - Get the MMIO address of PDC2027x extended registers 181 * @ap: Port 182 * @adev: device 183 * @offset: offset from mmio base 184 */ 185 static inline void __iomem *dev_mmio(struct ata_port *ap, struct ata_device *adev, unsigned int offset) 186 { 187 u8 adj = (adev->devno) ? 0x08 : 0x00; 188 return port_mmio(ap, offset) + adj; 189 } 190 191 /** 192 * pdc2027x_cable_detect - Probe host controller cable detect info 193 * @ap: Port for which cable detect info is desired 194 * 195 * Read 80c cable indicator from Promise extended register. 196 * This register is latched when the system is reset. 197 * 198 * LOCKING: 199 * None (inherited from caller). 200 */ 201 static int pdc2027x_cable_detect(struct ata_port *ap) 202 { 203 u32 cgcr; 204 205 /* check cable detect results */ 206 cgcr = ioread32(port_mmio(ap, PDC_GLOBAL_CTL)); 207 if (cgcr & (1 << 26)) 208 goto cbl40; 209 210 ata_port_dbg(ap, "No cable or 80-conductor cable\n"); 211 212 return ATA_CBL_PATA80; 213 cbl40: 214 ata_port_info(ap, DRV_NAME ":40-conductor cable detected\n"); 215 return ATA_CBL_PATA40; 216 } 217 218 /** 219 * pdc2027x_port_enabled - Check PDC ATA control register to see whether the port is enabled. 220 * @ap: Port to check 221 */ 222 static inline int pdc2027x_port_enabled(struct ata_port *ap) 223 { 224 return ioread8(port_mmio(ap, PDC_ATA_CTL)) & 0x02; 225 } 226 227 /** 228 * pdc2027x_prereset - prereset for PATA host controller 229 * @link: Target link 230 * @deadline: deadline jiffies for the operation 231 * 232 * Probeinit including cable detection. 233 * 234 * LOCKING: 235 * None (inherited from caller). 236 */ 237 238 static int pdc2027x_prereset(struct ata_link *link, unsigned long deadline) 239 { 240 /* Check whether port enabled */ 241 if (!pdc2027x_port_enabled(link->ap)) 242 return -ENOENT; 243 return ata_sff_prereset(link, deadline); 244 } 245 246 /** 247 * pdc2027x_mode_filter - mode selection filter 248 * @adev: ATA device 249 * @mask: list of modes proposed 250 * 251 * Block UDMA on devices that cause trouble with this controller. 252 */ 253 254 static unsigned int pdc2027x_mode_filter(struct ata_device *adev, unsigned int mask) 255 { 256 unsigned char model_num[ATA_ID_PROD_LEN + 1]; 257 struct ata_device *pair = ata_dev_pair(adev); 258 259 if (adev->class != ATA_DEV_ATA || adev->devno == 0 || pair == NULL) 260 return mask; 261 262 /* Check for slave of a Maxtor at UDMA6 */ 263 ata_id_c_string(pair->id, model_num, ATA_ID_PROD, 264 ATA_ID_PROD_LEN + 1); 265 /* If the master is a maxtor in UDMA6 then the slave should not use UDMA 6 */ 266 if (strstr(model_num, "Maxtor") == NULL && pair->dma_mode == XFER_UDMA_6) 267 mask &= ~ (1 << (6 + ATA_SHIFT_UDMA)); 268 269 return mask; 270 } 271 272 /** 273 * pdc2027x_set_piomode - Initialize host controller PATA PIO timings 274 * @ap: Port to configure 275 * @adev: um 276 * 277 * Set PIO mode for device. 278 * 279 * LOCKING: 280 * None (inherited from caller). 281 */ 282 283 static void pdc2027x_set_piomode(struct ata_port *ap, struct ata_device *adev) 284 { 285 unsigned int pio = adev->pio_mode - XFER_PIO_0; 286 u32 ctcr0, ctcr1; 287 288 ata_port_dbg(ap, "adev->pio_mode[%X]\n", adev->pio_mode); 289 290 /* Sanity check */ 291 if (pio > 4) { 292 ata_port_err(ap, "Unknown pio mode [%d] ignored\n", pio); 293 return; 294 295 } 296 297 /* Set the PIO timing registers using value table for 133MHz */ 298 ata_port_dbg(ap, "Set pio regs... \n"); 299 300 ctcr0 = ioread32(dev_mmio(ap, adev, PDC_CTCR0)); 301 ctcr0 &= 0xffff0000; 302 ctcr0 |= pdc2027x_pio_timing_tbl[pio].value0 | 303 (pdc2027x_pio_timing_tbl[pio].value1 << 8); 304 iowrite32(ctcr0, dev_mmio(ap, adev, PDC_CTCR0)); 305 306 ctcr1 = ioread32(dev_mmio(ap, adev, PDC_CTCR1)); 307 ctcr1 &= 0x00ffffff; 308 ctcr1 |= (pdc2027x_pio_timing_tbl[pio].value2 << 24); 309 iowrite32(ctcr1, dev_mmio(ap, adev, PDC_CTCR1)); 310 311 ata_port_dbg(ap, "Set to pio mode[%u] \n", pio); 312 } 313 314 /** 315 * pdc2027x_set_dmamode - Initialize host controller PATA UDMA timings 316 * @ap: Port to configure 317 * @adev: um 318 * 319 * Set UDMA mode for device. 320 * 321 * LOCKING: 322 * None (inherited from caller). 323 */ 324 static void pdc2027x_set_dmamode(struct ata_port *ap, struct ata_device *adev) 325 { 326 unsigned int dma_mode = adev->dma_mode; 327 u32 ctcr0, ctcr1; 328 329 if ((dma_mode >= XFER_UDMA_0) && 330 (dma_mode <= XFER_UDMA_6)) { 331 /* Set the UDMA timing registers with value table for 133MHz */ 332 unsigned int udma_mode = dma_mode & 0x07; 333 334 if (dma_mode == XFER_UDMA_2) { 335 /* 336 * Turn off tHOLD. 337 * If tHOLD is '1', the hardware will add half clock for data hold time. 338 * This code segment seems to be no effect. tHOLD will be overwritten below. 339 */ 340 ctcr1 = ioread32(dev_mmio(ap, adev, PDC_CTCR1)); 341 iowrite32(ctcr1 & ~(1 << 7), dev_mmio(ap, adev, PDC_CTCR1)); 342 } 343 344 ata_port_dbg(ap, "Set udma regs... \n"); 345 346 ctcr1 = ioread32(dev_mmio(ap, adev, PDC_CTCR1)); 347 ctcr1 &= 0xff000000; 348 ctcr1 |= pdc2027x_udma_timing_tbl[udma_mode].value0 | 349 (pdc2027x_udma_timing_tbl[udma_mode].value1 << 8) | 350 (pdc2027x_udma_timing_tbl[udma_mode].value2 << 16); 351 iowrite32(ctcr1, dev_mmio(ap, adev, PDC_CTCR1)); 352 353 ata_port_dbg(ap, "Set to udma mode[%u] \n", udma_mode); 354 355 } else if ((dma_mode >= XFER_MW_DMA_0) && 356 (dma_mode <= XFER_MW_DMA_2)) { 357 /* Set the MDMA timing registers with value table for 133MHz */ 358 unsigned int mdma_mode = dma_mode & 0x07; 359 360 ata_port_dbg(ap, "Set mdma regs... \n"); 361 ctcr0 = ioread32(dev_mmio(ap, adev, PDC_CTCR0)); 362 363 ctcr0 &= 0x0000ffff; 364 ctcr0 |= (pdc2027x_mdma_timing_tbl[mdma_mode].value0 << 16) | 365 (pdc2027x_mdma_timing_tbl[mdma_mode].value1 << 24); 366 367 iowrite32(ctcr0, dev_mmio(ap, adev, PDC_CTCR0)); 368 369 ata_port_dbg(ap, "Set to mdma mode[%u] \n", mdma_mode); 370 } else { 371 ata_port_err(ap, "Unknown dma mode [%u] ignored\n", dma_mode); 372 } 373 } 374 375 /** 376 * pdc2027x_set_mode - Set the timing registers back to correct values. 377 * @link: link to configure 378 * @r_failed: Returned device for failure 379 * 380 * The pdc2027x hardware will look at "SET FEATURES" and change the timing registers 381 * automatically. The values set by the hardware might be incorrect, under 133Mhz PLL. 382 * This function overwrites the possibly incorrect values set by the hardware to be correct. 383 */ 384 static int pdc2027x_set_mode(struct ata_link *link, struct ata_device **r_failed) 385 { 386 struct ata_port *ap = link->ap; 387 struct ata_device *dev; 388 int rc; 389 390 rc = ata_do_set_mode(link, r_failed); 391 if (rc < 0) 392 return rc; 393 394 ata_for_each_dev(dev, link, ENABLED) { 395 pdc2027x_set_piomode(ap, dev); 396 397 /* 398 * Enable prefetch if the device support PIO only. 399 */ 400 if (dev->xfer_shift == ATA_SHIFT_PIO) { 401 u32 ctcr1 = ioread32(dev_mmio(ap, dev, PDC_CTCR1)); 402 ctcr1 |= (1 << 25); 403 iowrite32(ctcr1, dev_mmio(ap, dev, PDC_CTCR1)); 404 405 ata_dev_dbg(dev, "Turn on prefetch\n"); 406 } else { 407 pdc2027x_set_dmamode(ap, dev); 408 } 409 } 410 return 0; 411 } 412 413 /** 414 * pdc2027x_check_atapi_dma - Check whether ATAPI DMA can be supported for this command 415 * @qc: Metadata associated with taskfile to check 416 * 417 * LOCKING: 418 * None (inherited from caller). 419 * 420 * RETURNS: 0 when ATAPI DMA can be used 421 * 1 otherwise 422 */ 423 static int pdc2027x_check_atapi_dma(struct ata_queued_cmd *qc) 424 { 425 struct scsi_cmnd *cmd = qc->scsicmd; 426 u8 *scsicmd = cmd->cmnd; 427 int rc = 1; /* atapi dma off by default */ 428 429 /* 430 * This workaround is from Promise's GPL driver. 431 * If ATAPI DMA is used for commands not in the 432 * following white list, say MODE_SENSE and REQUEST_SENSE, 433 * pdc2027x might hit the irq lost problem. 434 */ 435 switch (scsicmd[0]) { 436 case READ_10: 437 case WRITE_10: 438 case READ_12: 439 case WRITE_12: 440 case READ_6: 441 case WRITE_6: 442 case 0xad: /* READ_DVD_STRUCTURE */ 443 case 0xbe: /* READ_CD */ 444 /* ATAPI DMA is ok */ 445 rc = 0; 446 break; 447 default: 448 ; 449 } 450 451 return rc; 452 } 453 454 /** 455 * pdc_read_counter - Read the ctr counter 456 * @host: target ATA host 457 */ 458 459 static long pdc_read_counter(struct ata_host *host) 460 { 461 void __iomem *mmio_base = host->iomap[PDC_MMIO_BAR]; 462 long counter; 463 int retry = 1; 464 u32 bccrl, bccrh, bccrlv, bccrhv; 465 466 retry: 467 bccrl = ioread32(mmio_base + PDC_BYTE_COUNT) & 0x7fff; 468 bccrh = ioread32(mmio_base + PDC_BYTE_COUNT + 0x100) & 0x7fff; 469 470 /* Read the counter values again for verification */ 471 bccrlv = ioread32(mmio_base + PDC_BYTE_COUNT) & 0x7fff; 472 bccrhv = ioread32(mmio_base + PDC_BYTE_COUNT + 0x100) & 0x7fff; 473 474 counter = (bccrh << 15) | bccrl; 475 476 dev_dbg(host->dev, "bccrh [%X] bccrl [%X]\n", bccrh, bccrl); 477 dev_dbg(host->dev, "bccrhv[%X] bccrlv[%X]\n", bccrhv, bccrlv); 478 479 /* 480 * The 30-bit decreasing counter are read by 2 pieces. 481 * Incorrect value may be read when both bccrh and bccrl are changing. 482 * Ex. When 7900 decrease to 78FF, wrong value 7800 might be read. 483 */ 484 if (retry && !(bccrh == bccrhv && bccrl >= bccrlv)) { 485 retry--; 486 dev_dbg(host->dev, "rereading counter\n"); 487 goto retry; 488 } 489 490 return counter; 491 } 492 493 /** 494 * pdc_adjust_pll - Adjust the PLL input clock in Hz. 495 * 496 * @host: target ATA host 497 * @pll_clock: The input of PLL in HZ 498 * @board_idx: board identifier 499 */ 500 static void pdc_adjust_pll(struct ata_host *host, long pll_clock, unsigned int board_idx) 501 { 502 void __iomem *mmio_base = host->iomap[PDC_MMIO_BAR]; 503 u16 pll_ctl; 504 long pll_clock_khz = pll_clock / 1000; 505 long pout_required = board_idx? PDC_133_MHZ:PDC_100_MHZ; 506 long ratio = pout_required / pll_clock_khz; 507 int F, R; 508 509 /* Sanity check */ 510 if (unlikely(pll_clock_khz < 5000L || pll_clock_khz > 70000L)) { 511 dev_err(host->dev, "Invalid PLL input clock %ldkHz, give up!\n", 512 pll_clock_khz); 513 return; 514 } 515 516 dev_dbg(host->dev, "pout_required is %ld\n", pout_required); 517 518 /* Show the current clock value of PLL control register 519 * (maybe already configured by the firmware) 520 */ 521 pll_ctl = ioread16(mmio_base + PDC_PLL_CTL); 522 523 dev_dbg(host->dev, "pll_ctl[%X]\n", pll_ctl); 524 525 /* 526 * Calculate the ratio of F, R and OD 527 * POUT = (F + 2) / (( R + 2) * NO) 528 */ 529 if (ratio < 8600L) { /* 8.6x */ 530 /* Using NO = 0x01, R = 0x0D */ 531 R = 0x0d; 532 } else if (ratio < 12900L) { /* 12.9x */ 533 /* Using NO = 0x01, R = 0x08 */ 534 R = 0x08; 535 } else if (ratio < 16100L) { /* 16.1x */ 536 /* Using NO = 0x01, R = 0x06 */ 537 R = 0x06; 538 } else if (ratio < 64000L) { /* 64x */ 539 R = 0x00; 540 } else { 541 /* Invalid ratio */ 542 dev_err(host->dev, "Invalid ratio %ld, give up!\n", ratio); 543 return; 544 } 545 546 F = (ratio * (R+2)) / 1000 - 2; 547 548 if (unlikely(F < 0 || F > 127)) { 549 /* Invalid F */ 550 dev_err(host->dev, "F[%d] invalid!\n", F); 551 return; 552 } 553 554 dev_dbg(host->dev, "F[%d] R[%d] ratio*1000[%ld]\n", F, R, ratio); 555 556 pll_ctl = (R << 8) | F; 557 558 dev_dbg(host->dev, "Writing pll_ctl[%X]\n", pll_ctl); 559 560 iowrite16(pll_ctl, mmio_base + PDC_PLL_CTL); 561 ioread16(mmio_base + PDC_PLL_CTL); /* flush */ 562 563 /* Wait the PLL circuit to be stable */ 564 msleep(30); 565 566 /* 567 * Show the current clock value of PLL control register 568 * (maybe configured by the firmware) 569 */ 570 pll_ctl = ioread16(mmio_base + PDC_PLL_CTL); 571 572 dev_dbg(host->dev, "pll_ctl[%X]\n", pll_ctl); 573 574 return; 575 } 576 577 /** 578 * pdc_detect_pll_input_clock - Detect the PLL input clock in Hz. 579 * @host: target ATA host 580 * Ex. 16949000 on 33MHz PCI bus for pdc20275. 581 * Half of the PCI clock. 582 */ 583 static long pdc_detect_pll_input_clock(struct ata_host *host) 584 { 585 void __iomem *mmio_base = host->iomap[PDC_MMIO_BAR]; 586 u32 scr; 587 long start_count, end_count; 588 ktime_t start_time, end_time; 589 long pll_clock, usec_elapsed; 590 591 /* Start the test mode */ 592 scr = ioread32(mmio_base + PDC_SYS_CTL); 593 dev_dbg(host->dev, "scr[%X]\n", scr); 594 iowrite32(scr | (0x01 << 14), mmio_base + PDC_SYS_CTL); 595 ioread32(mmio_base + PDC_SYS_CTL); /* flush */ 596 597 /* Read current counter value */ 598 start_count = pdc_read_counter(host); 599 start_time = ktime_get(); 600 601 /* Let the counter run for 100 ms. */ 602 msleep(100); 603 604 /* Read the counter values again */ 605 end_count = pdc_read_counter(host); 606 end_time = ktime_get(); 607 608 /* Stop the test mode */ 609 scr = ioread32(mmio_base + PDC_SYS_CTL); 610 dev_dbg(host->dev, "scr[%X]\n", scr); 611 iowrite32(scr & ~(0x01 << 14), mmio_base + PDC_SYS_CTL); 612 ioread32(mmio_base + PDC_SYS_CTL); /* flush */ 613 614 /* calculate the input clock in Hz */ 615 usec_elapsed = (long) ktime_us_delta(end_time, start_time); 616 617 pll_clock = ((start_count - end_count) & 0x3fffffff) / 100 * 618 (100000000 / usec_elapsed); 619 620 dev_dbg(host->dev, "start[%ld] end[%ld] PLL input clock[%ld]HZ\n", 621 start_count, end_count, pll_clock); 622 623 return pll_clock; 624 } 625 626 /** 627 * pdc_hardware_init - Initialize the hardware. 628 * @host: target ATA host 629 * @board_idx: board identifier 630 */ 631 static void pdc_hardware_init(struct ata_host *host, unsigned int board_idx) 632 { 633 long pll_clock; 634 635 /* 636 * Detect PLL input clock rate. 637 * On some system, where PCI bus is running at non-standard clock rate. 638 * Ex. 25MHz or 40MHz, we have to adjust the cycle_time. 639 * The pdc20275 controller employs PLL circuit to help correct timing registers setting. 640 */ 641 pll_clock = pdc_detect_pll_input_clock(host); 642 643 dev_info(host->dev, "PLL input clock %ld kHz\n", pll_clock/1000); 644 645 /* Adjust PLL control register */ 646 pdc_adjust_pll(host, pll_clock, board_idx); 647 } 648 649 /** 650 * pdc_ata_setup_port - setup the mmio address 651 * @port: ata ioports to setup 652 * @base: base address 653 */ 654 static void pdc_ata_setup_port(struct ata_ioports *port, void __iomem *base) 655 { 656 port->cmd_addr = 657 port->data_addr = base; 658 port->feature_addr = 659 port->error_addr = base + 0x05; 660 port->nsect_addr = base + 0x0a; 661 port->lbal_addr = base + 0x0f; 662 port->lbam_addr = base + 0x10; 663 port->lbah_addr = base + 0x15; 664 port->device_addr = base + 0x1a; 665 port->command_addr = 666 port->status_addr = base + 0x1f; 667 port->altstatus_addr = 668 port->ctl_addr = base + 0x81a; 669 } 670 671 /** 672 * pdc2027x_init_one - PCI probe function 673 * Called when an instance of PCI adapter is inserted. 674 * This function checks whether the hardware is supported, 675 * initialize hardware and register an instance of ata_host to 676 * libata. (implements struct pci_driver.probe() ) 677 * 678 * @pdev: instance of pci_dev found 679 * @ent: matching entry in the id_tbl[] 680 */ 681 static int pdc2027x_init_one(struct pci_dev *pdev, 682 const struct pci_device_id *ent) 683 { 684 static const unsigned long cmd_offset[] = { 0x17c0, 0x15c0 }; 685 static const unsigned long bmdma_offset[] = { 0x1000, 0x1008 }; 686 unsigned int board_idx = (unsigned int) ent->driver_data; 687 const struct ata_port_info *ppi[] = 688 { &pdc2027x_port_info[board_idx], NULL }; 689 struct ata_host *host; 690 void __iomem *mmio_base; 691 int i, rc; 692 693 ata_print_version_once(&pdev->dev, DRV_VERSION); 694 695 /* alloc host */ 696 host = ata_host_alloc_pinfo(&pdev->dev, ppi, 2); 697 if (!host) 698 return -ENOMEM; 699 700 /* acquire resources and fill host */ 701 rc = pcim_enable_device(pdev); 702 if (rc) 703 return rc; 704 705 rc = pcim_iomap_regions(pdev, 1 << PDC_MMIO_BAR, DRV_NAME); 706 if (rc) 707 return rc; 708 host->iomap = pcim_iomap_table(pdev); 709 710 rc = dma_set_mask_and_coherent(&pdev->dev, ATA_DMA_MASK); 711 if (rc) 712 return rc; 713 714 mmio_base = host->iomap[PDC_MMIO_BAR]; 715 716 for (i = 0; i < 2; i++) { 717 struct ata_port *ap = host->ports[i]; 718 719 pdc_ata_setup_port(&ap->ioaddr, mmio_base + cmd_offset[i]); 720 ap->ioaddr.bmdma_addr = mmio_base + bmdma_offset[i]; 721 722 ata_port_pbar_desc(ap, PDC_MMIO_BAR, -1, "mmio"); 723 ata_port_pbar_desc(ap, PDC_MMIO_BAR, cmd_offset[i], "cmd"); 724 } 725 726 //pci_enable_intx(pdev); 727 728 /* initialize adapter */ 729 pdc_hardware_init(host, board_idx); 730 731 pci_set_master(pdev); 732 return ata_host_activate(host, pdev->irq, ata_bmdma_interrupt, 733 IRQF_SHARED, &pdc2027x_sht); 734 } 735 736 #ifdef CONFIG_PM_SLEEP 737 static int pdc2027x_reinit_one(struct pci_dev *pdev) 738 { 739 struct ata_host *host = pci_get_drvdata(pdev); 740 unsigned int board_idx; 741 int rc; 742 743 rc = ata_pci_device_do_resume(pdev); 744 if (rc) 745 return rc; 746 747 if (pdev->device == PCI_DEVICE_ID_PROMISE_20268 || 748 pdev->device == PCI_DEVICE_ID_PROMISE_20270) 749 board_idx = PDC_UDMA_100; 750 else 751 board_idx = PDC_UDMA_133; 752 753 pdc_hardware_init(host, board_idx); 754 755 ata_host_resume(host); 756 return 0; 757 } 758 #endif 759 760 module_pci_driver(pdc2027x_pci_driver); 761