1 // SPDX-License-Identifier: GPL-2.0-only
2 /*
3 * pata_optidma.c - Opti DMA PATA for new ATA layer
4 * (C) 2006 Red Hat Inc
5 *
6 * The Opti DMA controllers are related to the older PIO PCI controllers
7 * and indeed the VLB ones. The main differences are that the timing
8 * numbers are now based off PCI clocks not VLB and differ, and that
9 * MWDMA is supported.
10 *
11 * This driver should support Viper-N+, FireStar, FireStar Plus.
12 *
13 * These devices support virtual DMA for read (aka the CS5520). Later
14 * chips support UDMA33, but only if the rest of the board logic does,
15 * so you have to get this right. We don't support the virtual DMA
16 * but we do handle UDMA.
17 *
18 * Bits that are worth knowing
19 * Most control registers are shadowed into I/O registers
20 * 0x1F5 bit 0 tells you if the PCI/VLB clock is 33 or 25Mhz
21 * Virtual DMA registers *move* between rev 0x02 and rev 0x10
22 * UDMA requires a 66MHz FSB
23 *
24 */
25
26 #include <linux/kernel.h>
27 #include <linux/module.h>
28 #include <linux/pci.h>
29 #include <linux/blkdev.h>
30 #include <linux/delay.h>
31 #include <scsi/scsi_host.h>
32 #include <linux/libata.h>
33
34 #define DRV_NAME "pata_optidma"
35 #define DRV_VERSION "0.3.2"
36
37 enum {
38 READ_REG = 0, /* index of Read cycle timing register */
39 WRITE_REG = 1, /* index of Write cycle timing register */
40 CNTRL_REG = 3, /* index of Control register */
41 STRAP_REG = 5, /* index of Strap register */
42 MISC_REG = 6 /* index of Miscellaneous register */
43 };
44
45 static int pci_clock; /* 0 = 33 1 = 25 */
46
47 /**
48 * optidma_pre_reset - probe begin
49 * @link: ATA link
50 * @deadline: deadline jiffies for the operation
51 *
52 * Set up cable type and use generic probe init
53 */
54
optidma_pre_reset(struct ata_link * link,unsigned long deadline)55 static int optidma_pre_reset(struct ata_link *link, unsigned long deadline)
56 {
57 struct ata_port *ap = link->ap;
58 struct pci_dev *pdev = to_pci_dev(ap->host->dev);
59 static const struct pci_bits optidma_enable_bits = {
60 0x40, 1, 0x08, 0x00
61 };
62
63 if (ap->port_no && !pci_test_config_bits(pdev, &optidma_enable_bits))
64 return -ENOENT;
65
66 return ata_sff_prereset(link, deadline);
67 }
68
69 /**
70 * optidma_unlock - unlock control registers
71 * @ap: ATA port
72 *
73 * Unlock the control register block for this adapter. Registers must not
74 * be unlocked in a situation where libata might look at them.
75 */
76
optidma_unlock(struct ata_port * ap)77 static void optidma_unlock(struct ata_port *ap)
78 {
79 void __iomem *regio = ap->ioaddr.cmd_addr;
80
81 /* These 3 unlock the control register access */
82 ioread16(regio + 1);
83 ioread16(regio + 1);
84 iowrite8(3, regio + 2);
85 }
86
87 /**
88 * optidma_lock - issue temporary relock
89 * @ap: ATA port
90 *
91 * Re-lock the configuration register settings.
92 */
93
optidma_lock(struct ata_port * ap)94 static void optidma_lock(struct ata_port *ap)
95 {
96 void __iomem *regio = ap->ioaddr.cmd_addr;
97
98 /* Relock */
99 iowrite8(0x83, regio + 2);
100 }
101
102 /**
103 * optidma_mode_setup - set mode data
104 * @ap: ATA interface
105 * @adev: ATA device
106 * @mode: Mode to set
107 *
108 * Called to do the DMA or PIO mode setup. Timing numbers are all
109 * pre computed to keep the code clean. There are two tables depending
110 * on the hardware clock speed.
111 *
112 * WARNING: While we do this the IDE registers vanish. If we take an
113 * IRQ here we depend on the host set locking to avoid catastrophe.
114 */
115
optidma_mode_setup(struct ata_port * ap,struct ata_device * adev,u8 mode)116 static void optidma_mode_setup(struct ata_port *ap, struct ata_device *adev, u8 mode)
117 {
118 struct ata_device *pair = ata_dev_pair(adev);
119 int pio = adev->pio_mode - XFER_PIO_0;
120 int dma = adev->dma_mode - XFER_MW_DMA_0;
121 void __iomem *regio = ap->ioaddr.cmd_addr;
122 u8 addr;
123
124 /* Address table precomputed with a DCLK of 2 */
125 static const u8 addr_timing[2][5] = {
126 { 0x30, 0x20, 0x20, 0x10, 0x10 },
127 { 0x20, 0x20, 0x10, 0x10, 0x10 }
128 };
129 static const u8 data_rec_timing[2][5] = {
130 { 0x59, 0x46, 0x30, 0x20, 0x20 },
131 { 0x46, 0x32, 0x20, 0x20, 0x10 }
132 };
133 static const u8 dma_data_rec_timing[2][3] = {
134 { 0x76, 0x20, 0x20 },
135 { 0x54, 0x20, 0x10 }
136 };
137
138 /* Switch from IDE to control mode */
139 optidma_unlock(ap);
140
141
142 /*
143 * As with many controllers the address setup time is shared
144 * and must suit both devices if present. FIXME: Check if we
145 * need to look at slowest of PIO/DMA mode of either device
146 */
147
148 if (mode >= XFER_MW_DMA_0)
149 addr = 0;
150 else
151 addr = addr_timing[pci_clock][pio];
152
153 if (pair) {
154 u8 pair_addr;
155 /* Hardware constraint */
156 if (ata_dma_enabled(pair))
157 pair_addr = 0;
158 else
159 pair_addr = addr_timing[pci_clock][pair->pio_mode - XFER_PIO_0];
160 if (pair_addr > addr)
161 addr = pair_addr;
162 }
163
164 /* Commence primary programming sequence */
165 /* First we load the device number into the timing select */
166 iowrite8(adev->devno, regio + MISC_REG);
167 /* Now we load the data timings into read data/write data */
168 if (mode < XFER_MW_DMA_0) {
169 iowrite8(data_rec_timing[pci_clock][pio], regio + READ_REG);
170 iowrite8(data_rec_timing[pci_clock][pio], regio + WRITE_REG);
171 } else if (mode < XFER_UDMA_0) {
172 iowrite8(dma_data_rec_timing[pci_clock][dma], regio + READ_REG);
173 iowrite8(dma_data_rec_timing[pci_clock][dma], regio + WRITE_REG);
174 }
175 /* Finally we load the address setup into the misc register */
176 iowrite8(addr | adev->devno, regio + MISC_REG);
177
178 /* Programming sequence complete, timing 0 dev 0, timing 1 dev 1 */
179 iowrite8(0x85, regio + CNTRL_REG);
180
181 /* Switch back to IDE mode */
182 optidma_lock(ap);
183
184 /* Note: at this point our programming is incomplete. We are
185 not supposed to program PCI 0x43 "things we hacked onto the chip"
186 until we've done both sets of PIO/DMA timings */
187 }
188
189 /**
190 * optiplus_mode_setup - DMA setup for Firestar Plus
191 * @ap: ATA port
192 * @adev: device
193 * @mode: desired mode
194 *
195 * The Firestar plus has additional UDMA functionality for UDMA0-2 and
196 * requires we do some additional work. Because the base work we must do
197 * is mostly shared we wrap the Firestar setup functionality in this
198 * one
199 */
200
optiplus_mode_setup(struct ata_port * ap,struct ata_device * adev,u8 mode)201 static void optiplus_mode_setup(struct ata_port *ap, struct ata_device *adev, u8 mode)
202 {
203 struct pci_dev *pdev = to_pci_dev(ap->host->dev);
204 u8 udcfg;
205 u8 udslave;
206 int dev2 = 2 * adev->devno;
207 int unit = 2 * ap->port_no + adev->devno;
208 int udma = mode - XFER_UDMA_0;
209
210 pci_read_config_byte(pdev, 0x44, &udcfg);
211 if (mode <= XFER_UDMA_0) {
212 udcfg &= ~(1 << unit);
213 optidma_mode_setup(ap, adev, adev->dma_mode);
214 } else {
215 udcfg |= (1 << unit);
216 if (ap->port_no) {
217 pci_read_config_byte(pdev, 0x45, &udslave);
218 udslave &= ~(0x03 << dev2);
219 udslave |= (udma << dev2);
220 pci_write_config_byte(pdev, 0x45, udslave);
221 } else {
222 udcfg &= ~(0x30 << dev2);
223 udcfg |= (udma << dev2);
224 }
225 }
226 pci_write_config_byte(pdev, 0x44, udcfg);
227 }
228
229 /**
230 * optidma_set_pio_mode - PIO setup callback
231 * @ap: ATA port
232 * @adev: Device
233 *
234 * The libata core provides separate functions for handling PIO and
235 * DMA programming. The architecture of the Firestar makes it easier
236 * for us to have a common function so we provide wrappers
237 */
238
optidma_set_pio_mode(struct ata_port * ap,struct ata_device * adev)239 static void optidma_set_pio_mode(struct ata_port *ap, struct ata_device *adev)
240 {
241 optidma_mode_setup(ap, adev, adev->pio_mode);
242 }
243
244 /**
245 * optidma_set_dma_mode - DMA setup callback
246 * @ap: ATA port
247 * @adev: Device
248 *
249 * The libata core provides separate functions for handling PIO and
250 * DMA programming. The architecture of the Firestar makes it easier
251 * for us to have a common function so we provide wrappers
252 */
253
optidma_set_dma_mode(struct ata_port * ap,struct ata_device * adev)254 static void optidma_set_dma_mode(struct ata_port *ap, struct ata_device *adev)
255 {
256 optidma_mode_setup(ap, adev, adev->dma_mode);
257 }
258
259 /**
260 * optiplus_set_pio_mode - PIO setup callback
261 * @ap: ATA port
262 * @adev: Device
263 *
264 * The libata core provides separate functions for handling PIO and
265 * DMA programming. The architecture of the Firestar makes it easier
266 * for us to have a common function so we provide wrappers
267 */
268
optiplus_set_pio_mode(struct ata_port * ap,struct ata_device * adev)269 static void optiplus_set_pio_mode(struct ata_port *ap, struct ata_device *adev)
270 {
271 optiplus_mode_setup(ap, adev, adev->pio_mode);
272 }
273
274 /**
275 * optiplus_set_dma_mode - DMA setup callback
276 * @ap: ATA port
277 * @adev: Device
278 *
279 * The libata core provides separate functions for handling PIO and
280 * DMA programming. The architecture of the Firestar makes it easier
281 * for us to have a common function so we provide wrappers
282 */
283
optiplus_set_dma_mode(struct ata_port * ap,struct ata_device * adev)284 static void optiplus_set_dma_mode(struct ata_port *ap, struct ata_device *adev)
285 {
286 optiplus_mode_setup(ap, adev, adev->dma_mode);
287 }
288
289 /**
290 * optidma_make_bits43 - PCI setup helper
291 * @adev: ATA device
292 *
293 * Turn the ATA device setup into PCI configuration bits
294 * for register 0x43 and return the two bits needed.
295 */
296
optidma_make_bits43(struct ata_device * adev)297 static u8 optidma_make_bits43(struct ata_device *adev)
298 {
299 static const u8 bits43[5] = {
300 0, 0, 0, 1, 2
301 };
302 if (!ata_dev_enabled(adev))
303 return 0;
304 if (ata_dma_enabled(adev))
305 return adev->dma_mode - XFER_MW_DMA_0;
306 return bits43[adev->pio_mode - XFER_PIO_0];
307 }
308
309 /**
310 * optidma_set_mode - mode setup
311 * @link: link to set up
312 * @r_failed: out parameter for failed device
313 *
314 * Use the standard setup to tune the chipset and then finalise the
315 * configuration by writing the nibble of extra bits of data into
316 * the chip.
317 */
318
optidma_set_mode(struct ata_link * link,struct ata_device ** r_failed)319 static int optidma_set_mode(struct ata_link *link, struct ata_device **r_failed)
320 {
321 struct ata_port *ap = link->ap;
322 u8 r;
323 int nybble = 4 * ap->port_no;
324 struct pci_dev *pdev = to_pci_dev(ap->host->dev);
325 int rc = ata_do_set_mode(link, r_failed);
326 if (rc == 0) {
327 pci_read_config_byte(pdev, 0x43, &r);
328
329 r &= (0x0F << nybble);
330 r |= (optidma_make_bits43(&link->device[0]) +
331 (optidma_make_bits43(&link->device[0]) << 2)) << nybble;
332 pci_write_config_byte(pdev, 0x43, r);
333 }
334 return rc;
335 }
336
337 static const struct scsi_host_template optidma_sht = {
338 ATA_BMDMA_SHT(DRV_NAME),
339 };
340
341 static struct ata_port_operations optidma_port_ops = {
342 .inherits = &ata_bmdma_port_ops,
343 .cable_detect = ata_cable_40wire,
344 .set_piomode = optidma_set_pio_mode,
345 .set_dmamode = optidma_set_dma_mode,
346 .set_mode = optidma_set_mode,
347 .prereset = optidma_pre_reset,
348 };
349
350 static struct ata_port_operations optiplus_port_ops = {
351 .inherits = &optidma_port_ops,
352 .set_piomode = optiplus_set_pio_mode,
353 .set_dmamode = optiplus_set_dma_mode,
354 };
355
356 /**
357 * optiplus_with_udma - Look for UDMA capable setup
358 * @pdev: ATA controller
359 */
360
optiplus_with_udma(struct pci_dev * pdev)361 static int optiplus_with_udma(struct pci_dev *pdev)
362 {
363 u8 r;
364 int ret = 0;
365 int ioport = 0x22;
366 struct pci_dev *dev1;
367
368 /* Find function 1 */
369 dev1 = pci_get_device(0x1045, 0xC701, NULL);
370 if (dev1 == NULL)
371 return 0;
372
373 /* Rev must be >= 0x10 */
374 pci_read_config_byte(dev1, 0x08, &r);
375 if (r < 0x10)
376 goto done_nomsg;
377 /* Read the chipset system configuration to check our mode */
378 pci_read_config_byte(dev1, 0x5F, &r);
379 ioport |= (r << 8);
380 outb(0x10, ioport);
381 /* Must be 66Mhz sync */
382 if ((inb(ioport + 2) & 1) == 0)
383 goto done;
384
385 /* Check the ATA arbitration/timing is suitable */
386 pci_read_config_byte(pdev, 0x42, &r);
387 if ((r & 0x36) != 0x36)
388 goto done;
389 pci_read_config_byte(dev1, 0x52, &r);
390 if (r & 0x80) /* IDEDIR disabled */
391 ret = 1;
392 done:
393 printk(KERN_WARNING "UDMA not supported in this configuration.\n");
394 done_nomsg: /* Wrong chip revision */
395 pci_dev_put(dev1);
396 return ret;
397 }
398
optidma_init_one(struct pci_dev * dev,const struct pci_device_id * id)399 static int optidma_init_one(struct pci_dev *dev, const struct pci_device_id *id)
400 {
401 static const struct ata_port_info info_82c700 = {
402 .flags = ATA_FLAG_SLAVE_POSS,
403 .pio_mask = ATA_PIO4,
404 .mwdma_mask = ATA_MWDMA2,
405 .port_ops = &optidma_port_ops
406 };
407 static const struct ata_port_info info_82c700_udma = {
408 .flags = ATA_FLAG_SLAVE_POSS,
409 .pio_mask = ATA_PIO4,
410 .mwdma_mask = ATA_MWDMA2,
411 .udma_mask = ATA_UDMA2,
412 .port_ops = &optiplus_port_ops
413 };
414 const struct ata_port_info *ppi[] = { &info_82c700, NULL };
415 int rc;
416
417 ata_print_version_once(&dev->dev, DRV_VERSION);
418
419 rc = pcim_enable_device(dev);
420 if (rc)
421 return rc;
422
423 /* Fixed location chipset magic */
424 inw(0x1F1);
425 inw(0x1F1);
426 pci_clock = inb(0x1F5) & 1; /* 0 = 33Mhz, 1 = 25Mhz */
427
428 if (optiplus_with_udma(dev))
429 ppi[0] = &info_82c700_udma;
430
431 return ata_pci_bmdma_init_one(dev, ppi, &optidma_sht, NULL, 0);
432 }
433
434 static const struct pci_device_id optidma[] = {
435 { PCI_VDEVICE(OPTI, 0xD568), }, /* Opti 82C700 */
436
437 { },
438 };
439
440 static struct pci_driver optidma_pci_driver = {
441 .name = DRV_NAME,
442 .id_table = optidma,
443 .probe = optidma_init_one,
444 .remove = ata_pci_remove_one,
445 #ifdef CONFIG_PM_SLEEP
446 .suspend = ata_pci_device_suspend,
447 .resume = ata_pci_device_resume,
448 #endif
449 };
450
451 module_pci_driver(optidma_pci_driver);
452
453 MODULE_AUTHOR("Alan Cox");
454 MODULE_DESCRIPTION("low-level driver for Opti Firestar/Firestar Plus");
455 MODULE_LICENSE("GPL");
456 MODULE_DEVICE_TABLE(pci, optidma);
457 MODULE_VERSION(DRV_VERSION);
458