1 // SPDX-License-Identifier: GPL-2.0-only 2 /* 3 * pata_opti.c - ATI PATA for new ATA layer 4 * (C) 2005 Red Hat Inc 5 * 6 * Based on 7 * linux/drivers/ide/pci/opti621.c Version 0.7 Sept 10, 2002 8 * 9 * Copyright (C) 1996-1998 Linus Torvalds & authors (see below) 10 * 11 * Authors: 12 * Jaromir Koutek <miri@punknet.cz>, 13 * Jan Harkes <jaharkes@cwi.nl>, 14 * Mark Lord <mlord@pobox.com> 15 * Some parts of code are from ali14xx.c and from rz1000.c. 16 * 17 * Also consulted the FreeBSD prototype driver by Kevin Day to try 18 * and resolve some confusions. Further documentation can be found in 19 * Ralf Brown's interrupt list 20 * 21 * If you have other variants of the Opti range (Viper/Vendetta) please 22 * try this driver with those PCI idents and report back. For the later 23 * chips see the pata_optidma driver 24 * 25 */ 26 27 #include <linux/kernel.h> 28 #include <linux/module.h> 29 #include <linux/pci.h> 30 #include <linux/blkdev.h> 31 #include <linux/delay.h> 32 #include <scsi/scsi_host.h> 33 #include <linux/libata.h> 34 35 #define DRV_NAME "pata_opti" 36 #define DRV_VERSION "0.2.9" 37 38 enum { 39 READ_REG = 0, /* index of Read cycle timing register */ 40 WRITE_REG = 1, /* index of Write cycle timing register */ 41 CNTRL_REG = 3, /* index of Control register */ 42 STRAP_REG = 5, /* index of Strap register */ 43 MISC_REG = 6 /* index of Miscellaneous register */ 44 }; 45 46 /** 47 * opti_pre_reset - probe begin 48 * @link: ATA link 49 * @deadline: deadline jiffies for the operation 50 * 51 * Set up cable type and use generic probe init 52 */ 53 54 static int opti_pre_reset(struct ata_link *link, unsigned long deadline) 55 { 56 struct ata_port *ap = link->ap; 57 struct pci_dev *pdev = to_pci_dev(ap->host->dev); 58 static const struct pci_bits opti_enable_bits[] = { 59 { 0x45, 1, 0x80, 0x00 }, 60 { 0x40, 1, 0x08, 0x00 } 61 }; 62 63 if (!pci_test_config_bits(pdev, &opti_enable_bits[ap->port_no])) 64 return -ENOENT; 65 66 return ata_sff_prereset(link, deadline); 67 } 68 69 /** 70 * opti_write_reg - control register setup 71 * @ap: ATA port 72 * @val: value 73 * @reg: control register number 74 * 75 * The Opti uses magic 'trapdoor' register accesses to do configuration 76 * rather than using PCI space as other controllers do. The double inw 77 * on the error register activates configuration mode. We can then write 78 * the control register 79 */ 80 81 static void opti_write_reg(struct ata_port *ap, u8 val, int reg) 82 { 83 void __iomem *regio = ap->ioaddr.cmd_addr; 84 85 /* These 3 unlock the control register access */ 86 ioread16(regio + 1); 87 ioread16(regio + 1); 88 iowrite8(3, regio + 2); 89 90 /* Do the I/O */ 91 iowrite8(val, regio + reg); 92 93 /* Relock */ 94 iowrite8(0x83, regio + 2); 95 } 96 97 /** 98 * opti_set_piomode - set initial PIO mode data 99 * @ap: ATA interface 100 * @adev: ATA device 101 * 102 * Called to do the PIO mode setup. Timing numbers are taken from 103 * the FreeBSD driver then pre computed to keep the code clean. There 104 * are two tables depending on the hardware clock speed. 105 */ 106 107 static void opti_set_piomode(struct ata_port *ap, struct ata_device *adev) 108 { 109 struct ata_device *pair = ata_dev_pair(adev); 110 int clock; 111 int pio = adev->pio_mode - XFER_PIO_0; 112 void __iomem *regio = ap->ioaddr.cmd_addr; 113 u8 addr; 114 115 /* Address table precomputed with prefetch off and a DCLK of 2 */ 116 static const u8 addr_timing[2][5] = { 117 { 0x30, 0x20, 0x20, 0x10, 0x10 }, 118 { 0x20, 0x20, 0x10, 0x10, 0x10 } 119 }; 120 static const u8 data_rec_timing[2][5] = { 121 { 0x6B, 0x56, 0x42, 0x32, 0x31 }, 122 { 0x58, 0x44, 0x32, 0x22, 0x21 } 123 }; 124 125 iowrite8(0xff, regio + 5); 126 clock = ioread16(regio + 5) & 1; 127 128 /* 129 * As with many controllers the address setup time is shared 130 * and must suit both devices if present. 131 */ 132 133 addr = addr_timing[clock][pio]; 134 if (pair) { 135 /* Hardware constraint */ 136 u8 pair_addr = addr_timing[clock][pair->pio_mode - XFER_PIO_0]; 137 if (pair_addr > addr) 138 addr = pair_addr; 139 } 140 141 /* Commence primary programming sequence */ 142 opti_write_reg(ap, adev->devno, MISC_REG); 143 opti_write_reg(ap, data_rec_timing[clock][pio], READ_REG); 144 opti_write_reg(ap, data_rec_timing[clock][pio], WRITE_REG); 145 opti_write_reg(ap, addr, MISC_REG); 146 147 /* Programming sequence complete, override strapping */ 148 opti_write_reg(ap, 0x85, CNTRL_REG); 149 } 150 151 static const struct scsi_host_template opti_sht = { 152 ATA_PIO_SHT(DRV_NAME), 153 }; 154 155 static struct ata_port_operations opti_port_ops = { 156 .inherits = &ata_sff_port_ops, 157 .cable_detect = ata_cable_40wire, 158 .set_piomode = opti_set_piomode, 159 .prereset = opti_pre_reset, 160 }; 161 162 static int opti_init_one(struct pci_dev *dev, const struct pci_device_id *id) 163 { 164 static const struct ata_port_info info = { 165 .flags = ATA_FLAG_SLAVE_POSS, 166 .pio_mask = ATA_PIO4, 167 .port_ops = &opti_port_ops 168 }; 169 const struct ata_port_info *ppi[] = { &info, NULL }; 170 171 ata_print_version_once(&dev->dev, DRV_VERSION); 172 173 return ata_pci_sff_init_one(dev, ppi, &opti_sht, NULL, 0); 174 } 175 176 static const struct pci_device_id opti[] = { 177 { PCI_VDEVICE(OPTI, PCI_DEVICE_ID_OPTI_82C621), 0 }, 178 { PCI_VDEVICE(OPTI, PCI_DEVICE_ID_OPTI_82C825), 1 }, 179 180 { }, 181 }; 182 183 static struct pci_driver opti_pci_driver = { 184 .name = DRV_NAME, 185 .id_table = opti, 186 .probe = opti_init_one, 187 .remove = ata_pci_remove_one, 188 #ifdef CONFIG_PM_SLEEP 189 .suspend = ata_pci_device_suspend, 190 .resume = ata_pci_device_resume, 191 #endif 192 }; 193 194 module_pci_driver(opti_pci_driver); 195 196 MODULE_AUTHOR("Alan Cox"); 197 MODULE_DESCRIPTION("low-level driver for Opti 621/621X"); 198 MODULE_LICENSE("GPL"); 199 MODULE_DEVICE_TABLE(pci, opti); 200 MODULE_VERSION(DRV_VERSION); 201