1 // SPDX-License-Identifier: GPL-2.0-only 2 /* 3 * pata_oldpiix.c - Intel PATA/SATA controllers 4 * 5 * (C) 2005 Red Hat 6 * 7 * Some parts based on ata_piix.c by Jeff Garzik and others. 8 * 9 * Early PIIX differs significantly from the later PIIX as it lacks 10 * SITRE and the slave timing registers. This means that you have to 11 * set timing per channel, or be clever. Libata tells us whenever it 12 * does drive selection and we use this to reload the timings. 13 * 14 * Because of these behaviour differences PIIX gets its own driver module. 15 */ 16 17 #include <linux/kernel.h> 18 #include <linux/module.h> 19 #include <linux/pci.h> 20 #include <linux/blkdev.h> 21 #include <linux/delay.h> 22 #include <linux/device.h> 23 #include <scsi/scsi_host.h> 24 #include <linux/libata.h> 25 #include <linux/ata.h> 26 27 #define DRV_NAME "pata_oldpiix" 28 #define DRV_VERSION "0.5.5" 29 30 /** 31 * oldpiix_pre_reset - probe begin 32 * @link: ATA link 33 * @deadline: deadline jiffies for the operation 34 * 35 * Set up cable type and use generic probe init 36 */ 37 38 static int oldpiix_pre_reset(struct ata_link *link, unsigned long deadline) 39 { 40 struct ata_port *ap = link->ap; 41 struct pci_dev *pdev = to_pci_dev(ap->host->dev); 42 static const struct pci_bits oldpiix_enable_bits[] = { 43 { 0x41U, 1U, 0x80UL, 0x80UL }, /* port 0 */ 44 { 0x43U, 1U, 0x80UL, 0x80UL }, /* port 1 */ 45 }; 46 47 if (!pci_test_config_bits(pdev, &oldpiix_enable_bits[ap->port_no])) 48 return -ENOENT; 49 50 return ata_sff_prereset(link, deadline); 51 } 52 53 /** 54 * oldpiix_set_piomode - Initialize host controller PATA PIO timings 55 * @ap: Port whose timings we are configuring 56 * @adev: Device whose timings we are configuring 57 * 58 * Set PIO mode for device, in host controller PCI config space. 59 * 60 * LOCKING: 61 * None (inherited from caller). 62 */ 63 64 static void oldpiix_set_piomode (struct ata_port *ap, struct ata_device *adev) 65 { 66 unsigned int pio = adev->pio_mode - XFER_PIO_0; 67 struct pci_dev *dev = to_pci_dev(ap->host->dev); 68 unsigned int idetm_port= ap->port_no ? 0x42 : 0x40; 69 u16 idetm_data; 70 int control = 0; 71 72 /* 73 * See Intel Document 298600-004 for the timing programing rules 74 * for PIIX/ICH. Note that the early PIIX does not have the slave 75 * timing port at 0x44. 76 */ 77 78 static const /* ISP RTC */ 79 u8 timings[][2] = { { 0, 0 }, 80 { 0, 0 }, 81 { 1, 0 }, 82 { 2, 1 }, 83 { 2, 3 }, }; 84 85 if (pio > 1) 86 control |= 1; /* TIME */ 87 if (ata_pio_need_iordy(adev)) 88 control |= 2; /* IE */ 89 90 /* Intel specifies that the prefetch/posting is for disk only */ 91 if (adev->class == ATA_DEV_ATA) 92 control |= 4; /* PPE */ 93 94 pci_read_config_word(dev, idetm_port, &idetm_data); 95 96 /* 97 * Set PPE, IE and TIME as appropriate. 98 * Clear the other drive's timing bits. 99 */ 100 if (adev->devno == 0) { 101 idetm_data &= 0xCCE0; 102 idetm_data |= control; 103 } else { 104 idetm_data &= 0xCC0E; 105 idetm_data |= (control << 4); 106 } 107 idetm_data |= (timings[pio][0] << 12) | 108 (timings[pio][1] << 8); 109 pci_write_config_word(dev, idetm_port, idetm_data); 110 111 /* Track which port is configured */ 112 ap->private_data = adev; 113 } 114 115 /** 116 * oldpiix_set_dmamode - Initialize host controller PATA DMA timings 117 * @ap: Port whose timings we are configuring 118 * @adev: Device to program 119 * 120 * Set MWDMA mode for device, in host controller PCI config space. 121 * 122 * LOCKING: 123 * None (inherited from caller). 124 */ 125 126 static void oldpiix_set_dmamode (struct ata_port *ap, struct ata_device *adev) 127 { 128 struct pci_dev *dev = to_pci_dev(ap->host->dev); 129 u8 idetm_port = ap->port_no ? 0x42 : 0x40; 130 u16 idetm_data; 131 132 static const /* ISP RTC */ 133 u8 timings[][2] = { { 0, 0 }, 134 { 0, 0 }, 135 { 1, 0 }, 136 { 2, 1 }, 137 { 2, 3 }, }; 138 139 /* 140 * MWDMA is driven by the PIO timings. We must also enable 141 * IORDY unconditionally along with TIME1. PPE has already 142 * been set when the PIO timing was set. 143 */ 144 145 unsigned int mwdma = adev->dma_mode - XFER_MW_DMA_0; 146 unsigned int control; 147 const unsigned int needed_pio[3] = { 148 XFER_PIO_0, XFER_PIO_3, XFER_PIO_4 149 }; 150 int pio = needed_pio[mwdma] - XFER_PIO_0; 151 152 pci_read_config_word(dev, idetm_port, &idetm_data); 153 154 control = 3; /* IORDY|TIME0 */ 155 /* Intel specifies that the PPE functionality is for disk only */ 156 if (adev->class == ATA_DEV_ATA) 157 control |= 4; /* PPE enable */ 158 159 /* If the drive MWDMA is faster than it can do PIO then 160 we must force PIO into PIO0 */ 161 162 if (adev->pio_mode < needed_pio[mwdma]) 163 /* Enable DMA timing only */ 164 control |= 8; /* PIO cycles in PIO0 */ 165 166 /* Mask out the relevant control and timing bits we will load. Also 167 clear the other drive TIME register as a precaution */ 168 if (adev->devno == 0) { 169 idetm_data &= 0xCCE0; 170 idetm_data |= control; 171 } else { 172 idetm_data &= 0xCC0E; 173 idetm_data |= (control << 4); 174 } 175 idetm_data |= (timings[pio][0] << 12) | (timings[pio][1] << 8); 176 pci_write_config_word(dev, idetm_port, idetm_data); 177 178 /* Track which port is configured */ 179 ap->private_data = adev; 180 } 181 182 /** 183 * oldpiix_qc_issue - command issue 184 * @qc: command pending 185 * 186 * Called when the libata layer is about to issue a command. We wrap 187 * this interface so that we can load the correct ATA timings if 188 * necessary. Our logic also clears TIME0/TIME1 for the other device so 189 * that, even if we get this wrong, cycles to the other device will 190 * be made PIO0. 191 */ 192 193 static unsigned int oldpiix_qc_issue(struct ata_queued_cmd *qc) 194 { 195 struct ata_port *ap = qc->ap; 196 struct ata_device *adev = qc->dev; 197 198 if (adev != ap->private_data) { 199 oldpiix_set_piomode(ap, adev); 200 if (ata_dma_enabled(adev)) 201 oldpiix_set_dmamode(ap, adev); 202 } 203 return ata_bmdma_qc_issue(qc); 204 } 205 206 207 static struct scsi_host_template oldpiix_sht = { 208 ATA_BMDMA_SHT(DRV_NAME), 209 }; 210 211 static struct ata_port_operations oldpiix_pata_ops = { 212 .inherits = &ata_bmdma_port_ops, 213 .qc_issue = oldpiix_qc_issue, 214 .cable_detect = ata_cable_40wire, 215 .set_piomode = oldpiix_set_piomode, 216 .set_dmamode = oldpiix_set_dmamode, 217 .prereset = oldpiix_pre_reset, 218 }; 219 220 221 /** 222 * oldpiix_init_one - Register PIIX ATA PCI device with kernel services 223 * @pdev: PCI device to register 224 * @ent: Entry in oldpiix_pci_tbl matching with @pdev 225 * 226 * Called from kernel PCI layer. We probe for combined mode (sigh), 227 * and then hand over control to libata, for it to do the rest. 228 * 229 * LOCKING: 230 * Inherited from PCI layer (may sleep). 231 * 232 * RETURNS: 233 * Zero on success, or -ERRNO value. 234 */ 235 236 static int oldpiix_init_one (struct pci_dev *pdev, const struct pci_device_id *ent) 237 { 238 static const struct ata_port_info info = { 239 .flags = ATA_FLAG_SLAVE_POSS, 240 .pio_mask = ATA_PIO4, 241 .mwdma_mask = ATA_MWDMA12_ONLY, 242 .port_ops = &oldpiix_pata_ops, 243 }; 244 const struct ata_port_info *ppi[] = { &info, NULL }; 245 246 ata_print_version_once(&pdev->dev, DRV_VERSION); 247 248 return ata_pci_bmdma_init_one(pdev, ppi, &oldpiix_sht, NULL, 0); 249 } 250 251 static const struct pci_device_id oldpiix_pci_tbl[] = { 252 { PCI_VDEVICE(INTEL, 0x1230), }, 253 254 { } /* terminate list */ 255 }; 256 257 static struct pci_driver oldpiix_pci_driver = { 258 .name = DRV_NAME, 259 .id_table = oldpiix_pci_tbl, 260 .probe = oldpiix_init_one, 261 .remove = ata_pci_remove_one, 262 #ifdef CONFIG_PM_SLEEP 263 .suspend = ata_pci_device_suspend, 264 .resume = ata_pci_device_resume, 265 #endif 266 }; 267 268 module_pci_driver(oldpiix_pci_driver); 269 270 MODULE_AUTHOR("Alan Cox"); 271 MODULE_DESCRIPTION("SCSI low-level driver for early PIIX series controllers"); 272 MODULE_LICENSE("GPL"); 273 MODULE_DEVICE_TABLE(pci, oldpiix_pci_tbl); 274 MODULE_VERSION(DRV_VERSION); 275