1 /* 2 * pata_ns87415.c - NS87415 (non PARISC) PATA 3 * 4 * (C) 2005 Red Hat <alan@lxorguk.ukuu.org.uk> 5 * 6 * This is a fairly generic MWDMA controller. It has some limitations 7 * as it requires timing reloads on PIO/DMA transitions but it is otherwise 8 * fairly well designed. 9 * 10 * This driver assumes the firmware has left the chip in a valid ST506 11 * compliant state, either legacy IRQ 14/15 or native INTA shared. You 12 * may need to add platform code if your system fails to do this. 13 * 14 * The same cell appears in the 87560 controller used by some PARISC 15 * systems. This has its own special mountain of errata. 16 * 17 * TODO: 18 * Test PARISC SuperIO 19 * Get someone to test on SPARC 20 * Implement lazy pio/dma switching for better performance 21 * 8bit shared timing. 22 * See if we need to kill the FIFO for ATAPI 23 */ 24 25 #include <linux/kernel.h> 26 #include <linux/module.h> 27 #include <linux/pci.h> 28 #include <linux/init.h> 29 #include <linux/blkdev.h> 30 #include <linux/delay.h> 31 #include <linux/device.h> 32 #include <scsi/scsi_host.h> 33 #include <linux/libata.h> 34 #include <linux/ata.h> 35 36 #define DRV_NAME "pata_ns87415" 37 #define DRV_VERSION "0.0.1" 38 39 /** 40 * ns87415_set_mode - Initialize host controller mode timings 41 * @ap: Port whose timings we are configuring 42 * @adev: Device whose timings we are configuring 43 * @mode: Mode to set 44 * 45 * Program the mode registers for this controller, channel and 46 * device. Because the chip is quite an old design we have to do this 47 * for PIO/DMA switches. 48 * 49 * LOCKING: 50 * None (inherited from caller). 51 */ 52 53 static void ns87415_set_mode(struct ata_port *ap, struct ata_device *adev, u8 mode) 54 { 55 struct pci_dev *dev = to_pci_dev(ap->host->dev); 56 int unit = 2 * ap->port_no + adev->devno; 57 int timing = 0x44 + 2 * unit; 58 unsigned long T = 1000000000 / 33333; /* PCI clocks */ 59 struct ata_timing t; 60 u16 clocking; 61 u8 iordy; 62 u8 status; 63 64 /* Timing register format is 17 - low nybble read timing with 65 the high nybble being 16 - x for recovery time in PCI clocks */ 66 67 ata_timing_compute(adev, adev->pio_mode, &t, T, 0); 68 69 clocking = 17 - clamp_val(t.active, 2, 17); 70 clocking |= (16 - clamp_val(t.recover, 1, 16)) << 4; 71 /* Use the same timing for read and write bytes */ 72 clocking |= (clocking << 8); 73 pci_write_config_word(dev, timing, clocking); 74 75 /* Set the IORDY enable versus DMA enable on or off properly */ 76 pci_read_config_byte(dev, 0x42, &iordy); 77 iordy &= ~(1 << (4 + unit)); 78 if (mode >= XFER_MW_DMA_0 || !ata_pio_need_iordy(adev)) 79 iordy |= (1 << (4 + unit)); 80 81 /* Paranoia: We shouldn't ever get here with busy write buffers 82 but if so wait */ 83 84 pci_read_config_byte(dev, 0x43, &status); 85 while (status & 0x03) { 86 udelay(1); 87 pci_read_config_byte(dev, 0x43, &status); 88 } 89 /* Flip the IORDY/DMA bits now we are sure the write buffers are 90 clear */ 91 pci_write_config_byte(dev, 0x42, iordy); 92 93 /* TODO: Set byte 54 command timing to the best 8bit 94 mode shared by all four devices */ 95 } 96 97 /** 98 * ns87415_set_piomode - Initialize host controller PATA PIO timings 99 * @ap: Port whose timings we are configuring 100 * @adev: Device to program 101 * 102 * Set PIO mode for device, in host controller PCI config space. 103 * 104 * LOCKING: 105 * None (inherited from caller). 106 */ 107 108 static void ns87415_set_piomode(struct ata_port *ap, struct ata_device *adev) 109 { 110 ns87415_set_mode(ap, adev, adev->pio_mode); 111 } 112 113 /** 114 * ns87415_bmdma_setup - Set up DMA 115 * @qc: Command block 116 * 117 * Set up for bus masterng DMA. We have to do this ourselves 118 * rather than use the helper due to a chip erratum 119 */ 120 121 static void ns87415_bmdma_setup(struct ata_queued_cmd *qc) 122 { 123 struct ata_port *ap = qc->ap; 124 unsigned int rw = (qc->tf.flags & ATA_TFLAG_WRITE); 125 u8 dmactl; 126 127 /* load PRD table addr. */ 128 mb(); /* make sure PRD table writes are visible to controller */ 129 iowrite32(ap->bmdma_prd_dma, ap->ioaddr.bmdma_addr + ATA_DMA_TABLE_OFS); 130 131 /* specify data direction, triple-check start bit is clear */ 132 dmactl = ioread8(ap->ioaddr.bmdma_addr + ATA_DMA_CMD); 133 dmactl &= ~(ATA_DMA_WR | ATA_DMA_START); 134 /* Due to an erratum we need to write these bits to the wrong 135 place - which does save us an I/O bizarrely */ 136 dmactl |= ATA_DMA_INTR | ATA_DMA_ERR; 137 if (!rw) 138 dmactl |= ATA_DMA_WR; 139 iowrite8(dmactl, ap->ioaddr.bmdma_addr + ATA_DMA_CMD); 140 /* issue r/w command */ 141 ap->ops->sff_exec_command(ap, &qc->tf); 142 } 143 144 /** 145 * ns87415_bmdma_start - Begin DMA transfer 146 * @qc: Command block 147 * 148 * Switch the timings for the chip and set up for a DMA transfer 149 * before the DMA burst begins. 150 * 151 * FIXME: We should do lazy switching on bmdma_start versus 152 * ata_pio_data_xfer for better performance. 153 */ 154 155 static void ns87415_bmdma_start(struct ata_queued_cmd *qc) 156 { 157 ns87415_set_mode(qc->ap, qc->dev, qc->dev->dma_mode); 158 ata_bmdma_start(qc); 159 } 160 161 /** 162 * ns87415_bmdma_stop - End DMA transfer 163 * @qc: Command block 164 * 165 * End DMA mode and switch the controller back into PIO mode 166 */ 167 168 static void ns87415_bmdma_stop(struct ata_queued_cmd *qc) 169 { 170 ata_bmdma_stop(qc); 171 ns87415_set_mode(qc->ap, qc->dev, qc->dev->pio_mode); 172 } 173 174 /** 175 * ns87415_irq_clear - Clear interrupt 176 * @ap: Channel to clear 177 * 178 * Erratum: Due to a chip bug regisers 02 and 0A bit 1 and 2 (the 179 * error bits) are reset by writing to register 00 or 08. 180 */ 181 182 static void ns87415_irq_clear(struct ata_port *ap) 183 { 184 void __iomem *mmio = ap->ioaddr.bmdma_addr; 185 186 if (!mmio) 187 return; 188 iowrite8((ioread8(mmio + ATA_DMA_CMD) | ATA_DMA_INTR | ATA_DMA_ERR), 189 mmio + ATA_DMA_CMD); 190 } 191 192 /** 193 * ns87415_check_atapi_dma - ATAPI DMA filter 194 * @qc: Command block 195 * 196 * Disable ATAPI DMA (for now). We may be able to do DMA if we 197 * kill the prefetching. This isn't clear. 198 */ 199 200 static int ns87415_check_atapi_dma(struct ata_queued_cmd *qc) 201 { 202 return -EOPNOTSUPP; 203 } 204 205 #if defined(CONFIG_SUPERIO) 206 207 /* SUPERIO 87560 is a PoS chip that NatSem denies exists. 208 * Unfortunately, it's built-in on all Astro-based PA-RISC workstations 209 * which use the integrated NS87514 cell for CD-ROM support. 210 * i.e we have to support for CD-ROM installs. 211 * See drivers/parisc/superio.c for more gory details. 212 * 213 * Workarounds taken from drivers/ide/pci/ns87415.c 214 */ 215 216 #include <asm/superio.h> 217 218 #define SUPERIO_IDE_MAX_RETRIES 25 219 220 /** 221 * ns87560_read_buggy - workaround buggy Super I/O chip 222 * @port: Port to read 223 * 224 * Work around chipset problems in the 87560 SuperIO chip 225 */ 226 227 static u8 ns87560_read_buggy(void __iomem *port) 228 { 229 u8 tmp; 230 int retries = SUPERIO_IDE_MAX_RETRIES; 231 do { 232 tmp = ioread8(port); 233 if (tmp != 0) 234 return tmp; 235 udelay(50); 236 } while(retries-- > 0); 237 return tmp; 238 } 239 240 /** 241 * ns87560_check_status 242 * @ap: channel to check 243 * 244 * Return the status of the channel working around the 245 * 87560 flaws. 246 */ 247 248 static u8 ns87560_check_status(struct ata_port *ap) 249 { 250 return ns87560_read_buggy(ap->ioaddr.status_addr); 251 } 252 253 /** 254 * ns87560_tf_read - input device's ATA taskfile shadow registers 255 * @ap: Port from which input is read 256 * @tf: ATA taskfile register set for storing input 257 * 258 * Reads ATA taskfile registers for currently-selected device 259 * into @tf. Work around the 87560 bugs. 260 * 261 * LOCKING: 262 * Inherited from caller. 263 */ 264 void ns87560_tf_read(struct ata_port *ap, struct ata_taskfile *tf) 265 { 266 struct ata_ioports *ioaddr = &ap->ioaddr; 267 268 tf->command = ns87560_check_status(ap); 269 tf->feature = ioread8(ioaddr->error_addr); 270 tf->nsect = ioread8(ioaddr->nsect_addr); 271 tf->lbal = ioread8(ioaddr->lbal_addr); 272 tf->lbam = ioread8(ioaddr->lbam_addr); 273 tf->lbah = ioread8(ioaddr->lbah_addr); 274 tf->device = ns87560_read_buggy(ioaddr->device_addr); 275 276 if (tf->flags & ATA_TFLAG_LBA48) { 277 iowrite8(tf->ctl | ATA_HOB, ioaddr->ctl_addr); 278 tf->hob_feature = ioread8(ioaddr->error_addr); 279 tf->hob_nsect = ioread8(ioaddr->nsect_addr); 280 tf->hob_lbal = ioread8(ioaddr->lbal_addr); 281 tf->hob_lbam = ioread8(ioaddr->lbam_addr); 282 tf->hob_lbah = ioread8(ioaddr->lbah_addr); 283 iowrite8(tf->ctl, ioaddr->ctl_addr); 284 ap->last_ctl = tf->ctl; 285 } 286 } 287 288 /** 289 * ns87560_bmdma_status 290 * @ap: channel to check 291 * 292 * Return the DMA status of the channel working around the 293 * 87560 flaws. 294 */ 295 296 static u8 ns87560_bmdma_status(struct ata_port *ap) 297 { 298 return ns87560_read_buggy(ap->ioaddr.bmdma_addr + ATA_DMA_STATUS); 299 } 300 #endif /* 87560 SuperIO Support */ 301 302 static struct ata_port_operations ns87415_pata_ops = { 303 .inherits = &ata_bmdma_port_ops, 304 305 .check_atapi_dma = ns87415_check_atapi_dma, 306 .bmdma_setup = ns87415_bmdma_setup, 307 .bmdma_start = ns87415_bmdma_start, 308 .bmdma_stop = ns87415_bmdma_stop, 309 .sff_irq_clear = ns87415_irq_clear, 310 311 .cable_detect = ata_cable_40wire, 312 .set_piomode = ns87415_set_piomode, 313 }; 314 315 #if defined(CONFIG_SUPERIO) 316 static struct ata_port_operations ns87560_pata_ops = { 317 .inherits = &ns87415_pata_ops, 318 .sff_tf_read = ns87560_tf_read, 319 .sff_check_status = ns87560_check_status, 320 .bmdma_status = ns87560_bmdma_status, 321 }; 322 #endif 323 324 static struct scsi_host_template ns87415_sht = { 325 ATA_BMDMA_SHT(DRV_NAME), 326 }; 327 328 static void ns87415_fixup(struct pci_dev *pdev) 329 { 330 /* Select 512 byte sectors */ 331 pci_write_config_byte(pdev, 0x55, 0xEE); 332 /* Select PIO0 8bit clocking */ 333 pci_write_config_byte(pdev, 0x54, 0xB7); 334 } 335 336 /** 337 * ns87415_init_one - Register 87415 ATA PCI device with kernel services 338 * @pdev: PCI device to register 339 * @ent: Entry in ns87415_pci_tbl matching with @pdev 340 * 341 * Called from kernel PCI layer. We probe for combined mode (sigh), 342 * and then hand over control to libata, for it to do the rest. 343 * 344 * LOCKING: 345 * Inherited from PCI layer (may sleep). 346 * 347 * RETURNS: 348 * Zero on success, or -ERRNO value. 349 */ 350 351 static int ns87415_init_one (struct pci_dev *pdev, const struct pci_device_id *ent) 352 { 353 static const struct ata_port_info info = { 354 .flags = ATA_FLAG_SLAVE_POSS, 355 .pio_mask = ATA_PIO4, 356 .mwdma_mask = ATA_MWDMA2, 357 .port_ops = &ns87415_pata_ops, 358 }; 359 const struct ata_port_info *ppi[] = { &info, NULL }; 360 int rc; 361 #if defined(CONFIG_SUPERIO) 362 static const struct ata_port_info info87560 = { 363 .flags = ATA_FLAG_SLAVE_POSS, 364 .pio_mask = ATA_PIO4, 365 .mwdma_mask = ATA_MWDMA2, 366 .port_ops = &ns87560_pata_ops, 367 }; 368 369 if (PCI_SLOT(pdev->devfn) == 0x0E) 370 ppi[0] = &info87560; 371 #endif 372 ata_print_version_once(&pdev->dev, DRV_VERSION); 373 374 rc = pcim_enable_device(pdev); 375 if (rc) 376 return rc; 377 378 ns87415_fixup(pdev); 379 380 return ata_pci_bmdma_init_one(pdev, ppi, &ns87415_sht, NULL, 0); 381 } 382 383 static const struct pci_device_id ns87415_pci_tbl[] = { 384 { PCI_VDEVICE(NS, PCI_DEVICE_ID_NS_87415), }, 385 386 { } /* terminate list */ 387 }; 388 389 #ifdef CONFIG_PM 390 static int ns87415_reinit_one(struct pci_dev *pdev) 391 { 392 struct ata_host *host = pci_get_drvdata(pdev); 393 int rc; 394 395 rc = ata_pci_device_do_resume(pdev); 396 if (rc) 397 return rc; 398 399 ns87415_fixup(pdev); 400 401 ata_host_resume(host); 402 return 0; 403 } 404 #endif 405 406 static struct pci_driver ns87415_pci_driver = { 407 .name = DRV_NAME, 408 .id_table = ns87415_pci_tbl, 409 .probe = ns87415_init_one, 410 .remove = ata_pci_remove_one, 411 #ifdef CONFIG_PM 412 .suspend = ata_pci_device_suspend, 413 .resume = ns87415_reinit_one, 414 #endif 415 }; 416 417 module_pci_driver(ns87415_pci_driver); 418 419 MODULE_AUTHOR("Alan Cox"); 420 MODULE_DESCRIPTION("ATA low-level driver for NS87415 controllers"); 421 MODULE_LICENSE("GPL"); 422 MODULE_DEVICE_TABLE(pci, ns87415_pci_tbl); 423 MODULE_VERSION(DRV_VERSION); 424