1 /* 2 * pata_hpt3x3 - HPT3x3 driver 3 * (c) Copyright 2005-2006 Red Hat 4 * 5 * Was pata_hpt34x but the naming was confusing as it supported the 6 * 343 and 363 so it has been renamed. 7 * 8 * Based on: 9 * linux/drivers/ide/pci/hpt34x.c Version 0.40 Sept 10, 2002 10 * Copyright (C) 1998-2000 Andre Hedrick <andre@linux-ide.org> 11 * 12 * May be copied or modified under the terms of the GNU General Public 13 * License 14 */ 15 16 #include <linux/kernel.h> 17 #include <linux/module.h> 18 #include <linux/pci.h> 19 #include <linux/blkdev.h> 20 #include <linux/delay.h> 21 #include <scsi/scsi_host.h> 22 #include <linux/libata.h> 23 24 #define DRV_NAME "pata_hpt3x3" 25 #define DRV_VERSION "0.6.1" 26 27 /** 28 * hpt3x3_set_piomode - PIO setup 29 * @ap: ATA interface 30 * @adev: device on the interface 31 * 32 * Set our PIO requirements. This is fairly simple on the HPT3x3 as 33 * all we have to do is clear the MWDMA and UDMA bits then load the 34 * mode number. 35 */ 36 37 static void hpt3x3_set_piomode(struct ata_port *ap, struct ata_device *adev) 38 { 39 struct pci_dev *pdev = to_pci_dev(ap->host->dev); 40 u32 r1, r2; 41 int dn = 2 * ap->port_no + adev->devno; 42 43 pci_read_config_dword(pdev, 0x44, &r1); 44 pci_read_config_dword(pdev, 0x48, &r2); 45 /* Load the PIO timing number */ 46 r1 &= ~(7 << (3 * dn)); 47 r1 |= (adev->pio_mode - XFER_PIO_0) << (3 * dn); 48 r2 &= ~(0x11 << dn); /* Clear MWDMA and UDMA bits */ 49 50 pci_write_config_dword(pdev, 0x44, r1); 51 pci_write_config_dword(pdev, 0x48, r2); 52 } 53 54 #if defined(CONFIG_PATA_HPT3X3_DMA) 55 /** 56 * hpt3x3_set_dmamode - DMA timing setup 57 * @ap: ATA interface 58 * @adev: Device being configured 59 * 60 * Set up the channel for MWDMA or UDMA modes. Much the same as with 61 * PIO, load the mode number and then set MWDMA or UDMA flag. 62 * 63 * 0x44 : bit 0-2 master mode, 3-5 slave mode, etc 64 * 0x48 : bit 4/0 DMA/UDMA bit 5/1 for slave etc 65 */ 66 67 static void hpt3x3_set_dmamode(struct ata_port *ap, struct ata_device *adev) 68 { 69 struct pci_dev *pdev = to_pci_dev(ap->host->dev); 70 u32 r1, r2; 71 int dn = 2 * ap->port_no + adev->devno; 72 int mode_num = adev->dma_mode & 0x0F; 73 74 pci_read_config_dword(pdev, 0x44, &r1); 75 pci_read_config_dword(pdev, 0x48, &r2); 76 /* Load the timing number */ 77 r1 &= ~(7 << (3 * dn)); 78 r1 |= (mode_num << (3 * dn)); 79 r2 &= ~(0x11 << dn); /* Clear MWDMA and UDMA bits */ 80 81 if (adev->dma_mode >= XFER_UDMA_0) 82 r2 |= (0x01 << dn); /* Ultra mode */ 83 else 84 r2 |= (0x10 << dn); /* MWDMA */ 85 86 pci_write_config_dword(pdev, 0x44, r1); 87 pci_write_config_dword(pdev, 0x48, r2); 88 } 89 90 /** 91 * hpt3x3_freeze - DMA workaround 92 * @ap: port to freeze 93 * 94 * When freezing an HPT3x3 we must stop any pending DMA before 95 * writing to the control register or the chip will hang 96 */ 97 98 static void hpt3x3_freeze(struct ata_port *ap) 99 { 100 void __iomem *mmio = ap->ioaddr.bmdma_addr; 101 102 iowrite8(ioread8(mmio + ATA_DMA_CMD) & ~ ATA_DMA_START, 103 mmio + ATA_DMA_CMD); 104 ata_sff_dma_pause(ap); 105 ata_sff_freeze(ap); 106 } 107 108 /** 109 * hpt3x3_bmdma_setup - DMA workaround 110 * @qc: Queued command 111 * 112 * When issuing BMDMA we must clean up the error/active bits in 113 * software on this device 114 */ 115 116 static void hpt3x3_bmdma_setup(struct ata_queued_cmd *qc) 117 { 118 struct ata_port *ap = qc->ap; 119 u8 r = ioread8(ap->ioaddr.bmdma_addr + ATA_DMA_STATUS); 120 r |= ATA_DMA_INTR | ATA_DMA_ERR; 121 iowrite8(r, ap->ioaddr.bmdma_addr + ATA_DMA_STATUS); 122 return ata_bmdma_setup(qc); 123 } 124 125 /** 126 * hpt3x3_atapi_dma - ATAPI DMA check 127 * @qc: Queued command 128 * 129 * Just say no - we don't do ATAPI DMA 130 */ 131 132 static int hpt3x3_atapi_dma(struct ata_queued_cmd *qc) 133 { 134 return 1; 135 } 136 137 #endif /* CONFIG_PATA_HPT3X3_DMA */ 138 139 static const struct scsi_host_template hpt3x3_sht = { 140 ATA_BMDMA_SHT(DRV_NAME), 141 }; 142 143 static struct ata_port_operations hpt3x3_port_ops = { 144 .inherits = &ata_bmdma_port_ops, 145 .cable_detect = ata_cable_40wire, 146 .set_piomode = hpt3x3_set_piomode, 147 #if defined(CONFIG_PATA_HPT3X3_DMA) 148 .set_dmamode = hpt3x3_set_dmamode, 149 .bmdma_setup = hpt3x3_bmdma_setup, 150 .check_atapi_dma= hpt3x3_atapi_dma, 151 .freeze = hpt3x3_freeze, 152 #endif 153 154 }; 155 156 /** 157 * hpt3x3_init_chipset - chip setup 158 * @dev: PCI device 159 * 160 * Perform the setup required at boot and on resume. 161 */ 162 163 static void hpt3x3_init_chipset(struct pci_dev *dev) 164 { 165 u16 cmd; 166 /* Initialize the board */ 167 pci_write_config_word(dev, 0x80, 0x00); 168 /* Check if it is a 343 or a 363. 363 has COMMAND_MEMORY set */ 169 pci_read_config_word(dev, PCI_COMMAND, &cmd); 170 if (cmd & PCI_COMMAND_MEMORY) 171 pci_write_config_byte(dev, PCI_LATENCY_TIMER, 0xF0); 172 else 173 pci_write_config_byte(dev, PCI_LATENCY_TIMER, 0x20); 174 } 175 176 /** 177 * hpt3x3_init_one - Initialise an HPT343/363 178 * @pdev: PCI device 179 * @id: Entry in match table 180 * 181 * Perform basic initialisation. We set the device up so we access all 182 * ports via BAR4. This is necessary to work around errata. 183 */ 184 185 static int hpt3x3_init_one(struct pci_dev *pdev, const struct pci_device_id *id) 186 { 187 static const struct ata_port_info info = { 188 .flags = ATA_FLAG_SLAVE_POSS, 189 .pio_mask = ATA_PIO4, 190 #if defined(CONFIG_PATA_HPT3X3_DMA) 191 /* Further debug needed */ 192 .mwdma_mask = ATA_MWDMA2, 193 .udma_mask = ATA_UDMA2, 194 #endif 195 .port_ops = &hpt3x3_port_ops 196 }; 197 /* Register offsets of taskfiles in BAR4 area */ 198 static const u8 offset_cmd[2] = { 0x20, 0x28 }; 199 static const u8 offset_ctl[2] = { 0x36, 0x3E }; 200 const struct ata_port_info *ppi[] = { &info, NULL }; 201 struct ata_host *host; 202 int i, rc; 203 void __iomem *base; 204 205 hpt3x3_init_chipset(pdev); 206 207 ata_print_version_once(&pdev->dev, DRV_VERSION); 208 209 host = ata_host_alloc_pinfo(&pdev->dev, ppi, 2); 210 if (!host) 211 return -ENOMEM; 212 /* acquire resources and fill host */ 213 rc = pcim_enable_device(pdev); 214 if (rc) 215 return rc; 216 217 /* Everything is relative to BAR4 if we set up this way */ 218 rc = pcim_iomap_regions(pdev, 1 << 4, DRV_NAME); 219 if (rc == -EBUSY) 220 pcim_pin_device(pdev); 221 if (rc) 222 return rc; 223 host->iomap = pcim_iomap_table(pdev); 224 rc = dma_set_mask_and_coherent(&pdev->dev, ATA_DMA_MASK); 225 if (rc) 226 return rc; 227 228 base = host->iomap[4]; /* Bus mastering base */ 229 230 for (i = 0; i < host->n_ports; i++) { 231 struct ata_port *ap = host->ports[i]; 232 struct ata_ioports *ioaddr = &ap->ioaddr; 233 234 ioaddr->cmd_addr = base + offset_cmd[i]; 235 ioaddr->altstatus_addr = 236 ioaddr->ctl_addr = base + offset_ctl[i]; 237 ioaddr->scr_addr = NULL; 238 ata_sff_std_ports(ioaddr); 239 ioaddr->bmdma_addr = base + 8 * i; 240 241 ata_port_pbar_desc(ap, 4, -1, "ioport"); 242 ata_port_pbar_desc(ap, 4, offset_cmd[i], "cmd"); 243 } 244 pci_set_master(pdev); 245 return ata_host_activate(host, pdev->irq, ata_bmdma_interrupt, 246 IRQF_SHARED, &hpt3x3_sht); 247 } 248 249 #ifdef CONFIG_PM_SLEEP 250 static int hpt3x3_reinit_one(struct pci_dev *dev) 251 { 252 struct ata_host *host = pci_get_drvdata(dev); 253 int rc; 254 255 rc = ata_pci_device_do_resume(dev); 256 if (rc) 257 return rc; 258 259 hpt3x3_init_chipset(dev); 260 261 ata_host_resume(host); 262 return 0; 263 } 264 #endif 265 266 static const struct pci_device_id hpt3x3[] = { 267 { PCI_VDEVICE(TTI, PCI_DEVICE_ID_TTI_HPT343), }, 268 269 { }, 270 }; 271 272 static struct pci_driver hpt3x3_pci_driver = { 273 .name = DRV_NAME, 274 .id_table = hpt3x3, 275 .probe = hpt3x3_init_one, 276 .remove = ata_pci_remove_one, 277 #ifdef CONFIG_PM_SLEEP 278 .suspend = ata_pci_device_suspend, 279 .resume = hpt3x3_reinit_one, 280 #endif 281 }; 282 283 module_pci_driver(hpt3x3_pci_driver); 284 285 MODULE_AUTHOR("Alan Cox"); 286 MODULE_DESCRIPTION("low-level driver for the Highpoint HPT343/363"); 287 MODULE_LICENSE("GPL"); 288 MODULE_DEVICE_TABLE(pci, hpt3x3); 289 MODULE_VERSION(DRV_VERSION); 290