1 // SPDX-License-Identifier: GPL-2.0-only 2 /* 3 * Libata driver for the highpoint 37x and 30x UDMA66 ATA controllers. 4 * 5 * This driver is heavily based upon: 6 * 7 * linux/drivers/ide/pci/hpt366.c Version 0.36 April 25, 2003 8 * 9 * Copyright (C) 1999-2003 Andre Hedrick <andre@linux-ide.org> 10 * Portions Copyright (C) 2001 Sun Microsystems, Inc. 11 * Portions Copyright (C) 2003 Red Hat Inc 12 * Portions Copyright (C) 2005-2010 MontaVista Software, Inc. 13 * 14 * TODO 15 * Look into engine reset on timeout errors. Should not be required. 16 */ 17 #include <linux/kernel.h> 18 #include <linux/module.h> 19 #include <linux/pci.h> 20 #include <linux/blkdev.h> 21 #include <linux/delay.h> 22 #include <scsi/scsi_host.h> 23 #include <linux/libata.h> 24 25 #define DRV_NAME "pata_hpt37x" 26 #define DRV_VERSION "0.6.23" 27 28 struct hpt_clock { 29 u8 xfer_speed; 30 u32 timing; 31 }; 32 33 struct hpt_chip { 34 const char *name; 35 unsigned int base; 36 struct hpt_clock const *clocks[4]; 37 }; 38 39 /* key for bus clock timings 40 * bit 41 * 0:3 data_high_time. Inactive time of DIOW_/DIOR_ for PIO and MW DMA. 42 * cycles = value + 1 43 * 4:8 data_low_time. Active time of DIOW_/DIOR_ for PIO and MW DMA. 44 * cycles = value + 1 45 * 9:12 cmd_high_time. Inactive time of DIOW_/DIOR_ during task file 46 * register access. 47 * 13:17 cmd_low_time. Active time of DIOW_/DIOR_ during task file 48 * register access. 49 * 18:20 udma_cycle_time. Clock cycles for UDMA xfer. 50 * 21 CLK frequency for UDMA: 0=ATA clock, 1=dual ATA clock. 51 * 22:24 pre_high_time. Time to initialize 1st cycle for PIO and MW DMA xfer. 52 * 25:27 cmd_pre_high_time. Time to initialize 1st PIO cycle for task file 53 * register access. 54 * 28 UDMA enable. 55 * 29 DMA enable. 56 * 30 PIO_MST enable. If set, the chip is in bus master mode during 57 * PIO xfer. 58 * 31 FIFO enable. Only for PIO. 59 */ 60 61 static struct hpt_clock hpt37x_timings_33[] = { 62 { XFER_UDMA_6, 0x12446231 }, /* 0x12646231 ?? */ 63 { XFER_UDMA_5, 0x12446231 }, 64 { XFER_UDMA_4, 0x12446231 }, 65 { XFER_UDMA_3, 0x126c6231 }, 66 { XFER_UDMA_2, 0x12486231 }, 67 { XFER_UDMA_1, 0x124c6233 }, 68 { XFER_UDMA_0, 0x12506297 }, 69 70 { XFER_MW_DMA_2, 0x22406c31 }, 71 { XFER_MW_DMA_1, 0x22406c33 }, 72 { XFER_MW_DMA_0, 0x22406c97 }, 73 74 { XFER_PIO_4, 0x06414e31 }, 75 { XFER_PIO_3, 0x06414e42 }, 76 { XFER_PIO_2, 0x06414e53 }, 77 { XFER_PIO_1, 0x06814e93 }, 78 { XFER_PIO_0, 0x06814ea7 } 79 }; 80 81 static struct hpt_clock hpt37x_timings_50[] = { 82 { XFER_UDMA_6, 0x12848242 }, 83 { XFER_UDMA_5, 0x12848242 }, 84 { XFER_UDMA_4, 0x12ac8242 }, 85 { XFER_UDMA_3, 0x128c8242 }, 86 { XFER_UDMA_2, 0x120c8242 }, 87 { XFER_UDMA_1, 0x12148254 }, 88 { XFER_UDMA_0, 0x121882ea }, 89 90 { XFER_MW_DMA_2, 0x22808242 }, 91 { XFER_MW_DMA_1, 0x22808254 }, 92 { XFER_MW_DMA_0, 0x228082ea }, 93 94 { XFER_PIO_4, 0x0a81f442 }, 95 { XFER_PIO_3, 0x0a81f443 }, 96 { XFER_PIO_2, 0x0a81f454 }, 97 { XFER_PIO_1, 0x0ac1f465 }, 98 { XFER_PIO_0, 0x0ac1f48a } 99 }; 100 101 static struct hpt_clock hpt37x_timings_66[] = { 102 { XFER_UDMA_6, 0x1c869c62 }, 103 { XFER_UDMA_5, 0x1cae9c62 }, /* 0x1c8a9c62 */ 104 { XFER_UDMA_4, 0x1c8a9c62 }, 105 { XFER_UDMA_3, 0x1c8e9c62 }, 106 { XFER_UDMA_2, 0x1c929c62 }, 107 { XFER_UDMA_1, 0x1c9a9c62 }, 108 { XFER_UDMA_0, 0x1c829c62 }, 109 110 { XFER_MW_DMA_2, 0x2c829c62 }, 111 { XFER_MW_DMA_1, 0x2c829c66 }, 112 { XFER_MW_DMA_0, 0x2c829d2e }, 113 114 { XFER_PIO_4, 0x0c829c62 }, 115 { XFER_PIO_3, 0x0c829c84 }, 116 { XFER_PIO_2, 0x0c829ca6 }, 117 { XFER_PIO_1, 0x0d029d26 }, 118 { XFER_PIO_0, 0x0d029d5e } 119 }; 120 121 122 static const struct hpt_chip hpt370 = { 123 "HPT370", 124 48, 125 { 126 hpt37x_timings_33, 127 NULL, 128 NULL, 129 NULL 130 } 131 }; 132 133 static const struct hpt_chip hpt370a = { 134 "HPT370A", 135 48, 136 { 137 hpt37x_timings_33, 138 NULL, 139 hpt37x_timings_50, 140 NULL 141 } 142 }; 143 144 static const struct hpt_chip hpt372 = { 145 "HPT372", 146 55, 147 { 148 hpt37x_timings_33, 149 NULL, 150 hpt37x_timings_50, 151 hpt37x_timings_66 152 } 153 }; 154 155 static const struct hpt_chip hpt302 = { 156 "HPT302", 157 66, 158 { 159 hpt37x_timings_33, 160 NULL, 161 hpt37x_timings_50, 162 hpt37x_timings_66 163 } 164 }; 165 166 static const struct hpt_chip hpt371 = { 167 "HPT371", 168 66, 169 { 170 hpt37x_timings_33, 171 NULL, 172 hpt37x_timings_50, 173 hpt37x_timings_66 174 } 175 }; 176 177 static const struct hpt_chip hpt372a = { 178 "HPT372A", 179 66, 180 { 181 hpt37x_timings_33, 182 NULL, 183 hpt37x_timings_50, 184 hpt37x_timings_66 185 } 186 }; 187 188 static const struct hpt_chip hpt374 = { 189 "HPT374", 190 48, 191 { 192 hpt37x_timings_33, 193 NULL, 194 NULL, 195 NULL 196 } 197 }; 198 199 /** 200 * hpt37x_find_mode - reset the hpt37x bus 201 * @ap: ATA port 202 * @speed: transfer mode 203 * 204 * Return the 32bit register programming information for this channel 205 * that matches the speed provided. 206 */ 207 208 static u32 hpt37x_find_mode(struct ata_port *ap, int speed) 209 { 210 struct hpt_clock *clocks = ap->host->private_data; 211 212 while (clocks->xfer_speed) { 213 if (clocks->xfer_speed == speed) 214 return clocks->timing; 215 clocks++; 216 } 217 BUG(); 218 return 0xffffffffU; /* silence compiler warning */ 219 } 220 221 static int hpt_dma_blacklisted(const struct ata_device *dev, char *modestr, 222 const char * const list[]) 223 { 224 unsigned char model_num[ATA_ID_PROD_LEN + 1]; 225 int i; 226 227 ata_id_c_string(dev->id, model_num, ATA_ID_PROD, sizeof(model_num)); 228 229 i = match_string(list, -1, model_num); 230 if (i >= 0) { 231 ata_dev_warn(dev, "%s is not supported for %s\n", 232 modestr, list[i]); 233 return 1; 234 } 235 return 0; 236 } 237 238 static const char * const bad_ata33[] = { 239 "Maxtor 92720U8", "Maxtor 92040U6", "Maxtor 91360U4", "Maxtor 91020U3", 240 "Maxtor 90845U3", "Maxtor 90650U2", 241 "Maxtor 91360D8", "Maxtor 91190D7", "Maxtor 91020D6", "Maxtor 90845D5", 242 "Maxtor 90680D4", "Maxtor 90510D3", "Maxtor 90340D2", 243 "Maxtor 91152D8", "Maxtor 91008D7", "Maxtor 90845D6", "Maxtor 90840D6", 244 "Maxtor 90720D5", "Maxtor 90648D5", "Maxtor 90576D4", 245 "Maxtor 90510D4", 246 "Maxtor 90432D3", "Maxtor 90288D2", "Maxtor 90256D2", 247 "Maxtor 91000D8", "Maxtor 90910D8", "Maxtor 90875D7", "Maxtor 90840D7", 248 "Maxtor 90750D6", "Maxtor 90625D5", "Maxtor 90500D4", 249 "Maxtor 91728D8", "Maxtor 91512D7", "Maxtor 91303D6", "Maxtor 91080D5", 250 "Maxtor 90845D4", "Maxtor 90680D4", "Maxtor 90648D3", "Maxtor 90432D2", 251 NULL 252 }; 253 254 static const char * const bad_ata100_5[] = { 255 "IBM-DTLA-307075", 256 "IBM-DTLA-307060", 257 "IBM-DTLA-307045", 258 "IBM-DTLA-307030", 259 "IBM-DTLA-307020", 260 "IBM-DTLA-307015", 261 "IBM-DTLA-305040", 262 "IBM-DTLA-305030", 263 "IBM-DTLA-305020", 264 "IC35L010AVER07-0", 265 "IC35L020AVER07-0", 266 "IC35L030AVER07-0", 267 "IC35L040AVER07-0", 268 "IC35L060AVER07-0", 269 "WDC AC310200R", 270 NULL 271 }; 272 273 /** 274 * hpt370_filter - mode selection filter 275 * @adev: ATA device 276 * @mask: mode mask 277 * 278 * Block UDMA on devices that cause trouble with this controller. 279 */ 280 281 static unsigned long hpt370_filter(struct ata_device *adev, unsigned long mask) 282 { 283 if (adev->class == ATA_DEV_ATA) { 284 if (hpt_dma_blacklisted(adev, "UDMA", bad_ata33)) 285 mask &= ~ATA_MASK_UDMA; 286 if (hpt_dma_blacklisted(adev, "UDMA100", bad_ata100_5)) 287 mask &= ~(0xE0 << ATA_SHIFT_UDMA); 288 } 289 return mask; 290 } 291 292 /** 293 * hpt370a_filter - mode selection filter 294 * @adev: ATA device 295 * @mask: mode mask 296 * 297 * Block UDMA on devices that cause trouble with this controller. 298 */ 299 300 static unsigned long hpt370a_filter(struct ata_device *adev, unsigned long mask) 301 { 302 if (adev->class == ATA_DEV_ATA) { 303 if (hpt_dma_blacklisted(adev, "UDMA100", bad_ata100_5)) 304 mask &= ~(0xE0 << ATA_SHIFT_UDMA); 305 } 306 return mask; 307 } 308 309 /** 310 * hpt372_filter - mode selection filter 311 * @adev: ATA device 312 * @mask: mode mask 313 * 314 * The Marvell bridge chips used on the HighPoint SATA cards do not seem 315 * to support the UltraDMA modes 1, 2, and 3 as well as any MWDMA modes... 316 */ 317 static unsigned long hpt372_filter(struct ata_device *adev, unsigned long mask) 318 { 319 if (ata_id_is_sata(adev->id)) 320 mask &= ~((0xE << ATA_SHIFT_UDMA) | ATA_MASK_MWDMA); 321 322 return mask; 323 } 324 325 /** 326 * hpt37x_cable_detect - Detect the cable type 327 * @ap: ATA port to detect on 328 * 329 * Return the cable type attached to this port 330 */ 331 332 static int hpt37x_cable_detect(struct ata_port *ap) 333 { 334 struct pci_dev *pdev = to_pci_dev(ap->host->dev); 335 u8 scr2, ata66; 336 337 pci_read_config_byte(pdev, 0x5B, &scr2); 338 pci_write_config_byte(pdev, 0x5B, scr2 & ~0x01); 339 340 udelay(10); /* debounce */ 341 342 /* Cable register now active */ 343 pci_read_config_byte(pdev, 0x5A, &ata66); 344 /* Restore state */ 345 pci_write_config_byte(pdev, 0x5B, scr2); 346 347 if (ata66 & (2 >> ap->port_no)) 348 return ATA_CBL_PATA40; 349 else 350 return ATA_CBL_PATA80; 351 } 352 353 /** 354 * hpt374_fn1_cable_detect - Detect the cable type 355 * @ap: ATA port to detect on 356 * 357 * Return the cable type attached to this port 358 */ 359 360 static int hpt374_fn1_cable_detect(struct ata_port *ap) 361 { 362 struct pci_dev *pdev = to_pci_dev(ap->host->dev); 363 unsigned int mcrbase = 0x50 + 4 * ap->port_no; 364 u16 mcr3; 365 u8 ata66; 366 367 /* Do the extra channel work */ 368 pci_read_config_word(pdev, mcrbase + 2, &mcr3); 369 /* Set bit 15 of 0x52 to enable TCBLID as input */ 370 pci_write_config_word(pdev, mcrbase + 2, mcr3 | 0x8000); 371 pci_read_config_byte(pdev, 0x5A, &ata66); 372 /* Reset TCBLID/FCBLID to output */ 373 pci_write_config_word(pdev, mcrbase + 2, mcr3); 374 375 if (ata66 & (2 >> ap->port_no)) 376 return ATA_CBL_PATA40; 377 else 378 return ATA_CBL_PATA80; 379 } 380 381 /** 382 * hpt37x_pre_reset - reset the hpt37x bus 383 * @link: ATA link to reset 384 * @deadline: deadline jiffies for the operation 385 * 386 * Perform the initial reset handling for the HPT37x. 387 */ 388 389 static int hpt37x_pre_reset(struct ata_link *link, unsigned long deadline) 390 { 391 struct ata_port *ap = link->ap; 392 struct pci_dev *pdev = to_pci_dev(ap->host->dev); 393 static const struct pci_bits hpt37x_enable_bits[] = { 394 { 0x50, 1, 0x04, 0x04 }, 395 { 0x54, 1, 0x04, 0x04 } 396 }; 397 398 if (!pci_test_config_bits(pdev, &hpt37x_enable_bits[ap->port_no])) 399 return -ENOENT; 400 401 /* Reset the state machine */ 402 pci_write_config_byte(pdev, 0x50 + 4 * ap->port_no, 0x37); 403 udelay(100); 404 405 return ata_sff_prereset(link, deadline); 406 } 407 408 static void hpt370_set_mode(struct ata_port *ap, struct ata_device *adev, 409 u8 mode) 410 { 411 struct pci_dev *pdev = to_pci_dev(ap->host->dev); 412 u32 addr1, addr2; 413 u32 reg, timing, mask; 414 u8 fast; 415 416 addr1 = 0x40 + 4 * (adev->devno + 2 * ap->port_no); 417 addr2 = 0x51 + 4 * ap->port_no; 418 419 /* Fast interrupt prediction disable, hold off interrupt disable */ 420 pci_read_config_byte(pdev, addr2, &fast); 421 fast &= ~0x02; 422 fast |= 0x01; 423 pci_write_config_byte(pdev, addr2, fast); 424 425 /* Determine timing mask and find matching mode entry */ 426 if (mode < XFER_MW_DMA_0) 427 mask = 0xcfc3ffff; 428 else if (mode < XFER_UDMA_0) 429 mask = 0x31c001ff; 430 else 431 mask = 0x303c0000; 432 433 timing = hpt37x_find_mode(ap, mode); 434 435 pci_read_config_dword(pdev, addr1, ®); 436 reg = (reg & ~mask) | (timing & mask); 437 pci_write_config_dword(pdev, addr1, reg); 438 } 439 /** 440 * hpt370_set_piomode - PIO setup 441 * @ap: ATA interface 442 * @adev: device on the interface 443 * 444 * Perform PIO mode setup. 445 */ 446 447 static void hpt370_set_piomode(struct ata_port *ap, struct ata_device *adev) 448 { 449 hpt370_set_mode(ap, adev, adev->pio_mode); 450 } 451 452 /** 453 * hpt370_set_dmamode - DMA timing setup 454 * @ap: ATA interface 455 * @adev: Device being configured 456 * 457 * Set up the channel for MWDMA or UDMA modes. 458 */ 459 460 static void hpt370_set_dmamode(struct ata_port *ap, struct ata_device *adev) 461 { 462 hpt370_set_mode(ap, adev, adev->dma_mode); 463 } 464 465 /** 466 * hpt370_bmdma_stop - DMA engine stop 467 * @qc: ATA command 468 * 469 * Work around the HPT370 DMA engine. 470 */ 471 472 static void hpt370_bmdma_stop(struct ata_queued_cmd *qc) 473 { 474 struct ata_port *ap = qc->ap; 475 struct pci_dev *pdev = to_pci_dev(ap->host->dev); 476 void __iomem *bmdma = ap->ioaddr.bmdma_addr; 477 u8 dma_stat = ioread8(bmdma + ATA_DMA_STATUS); 478 u8 dma_cmd; 479 480 if (dma_stat & ATA_DMA_ACTIVE) { 481 udelay(20); 482 dma_stat = ioread8(bmdma + ATA_DMA_STATUS); 483 } 484 if (dma_stat & ATA_DMA_ACTIVE) { 485 /* Clear the engine */ 486 pci_write_config_byte(pdev, 0x50 + 4 * ap->port_no, 0x37); 487 udelay(10); 488 /* Stop DMA */ 489 dma_cmd = ioread8(bmdma + ATA_DMA_CMD); 490 iowrite8(dma_cmd & ~ATA_DMA_START, bmdma + ATA_DMA_CMD); 491 /* Clear Error */ 492 dma_stat = ioread8(bmdma + ATA_DMA_STATUS); 493 iowrite8(dma_stat | ATA_DMA_INTR | ATA_DMA_ERR, 494 bmdma + ATA_DMA_STATUS); 495 /* Clear the engine */ 496 pci_write_config_byte(pdev, 0x50 + 4 * ap->port_no, 0x37); 497 udelay(10); 498 } 499 ata_bmdma_stop(qc); 500 } 501 502 static void hpt372_set_mode(struct ata_port *ap, struct ata_device *adev, 503 u8 mode) 504 { 505 struct pci_dev *pdev = to_pci_dev(ap->host->dev); 506 u32 addr1, addr2; 507 u32 reg, timing, mask; 508 u8 fast; 509 510 addr1 = 0x40 + 4 * (adev->devno + 2 * ap->port_no); 511 addr2 = 0x51 + 4 * ap->port_no; 512 513 /* Fast interrupt prediction disable, hold off interrupt disable */ 514 pci_read_config_byte(pdev, addr2, &fast); 515 fast &= ~0x07; 516 pci_write_config_byte(pdev, addr2, fast); 517 518 /* Determine timing mask and find matching mode entry */ 519 if (mode < XFER_MW_DMA_0) 520 mask = 0xcfc3ffff; 521 else if (mode < XFER_UDMA_0) 522 mask = 0x31c001ff; 523 else 524 mask = 0x303c0000; 525 526 timing = hpt37x_find_mode(ap, mode); 527 528 pci_read_config_dword(pdev, addr1, ®); 529 reg = (reg & ~mask) | (timing & mask); 530 pci_write_config_dword(pdev, addr1, reg); 531 } 532 533 /** 534 * hpt372_set_piomode - PIO setup 535 * @ap: ATA interface 536 * @adev: device on the interface 537 * 538 * Perform PIO mode setup. 539 */ 540 541 static void hpt372_set_piomode(struct ata_port *ap, struct ata_device *adev) 542 { 543 hpt372_set_mode(ap, adev, adev->pio_mode); 544 } 545 546 /** 547 * hpt372_set_dmamode - DMA timing setup 548 * @ap: ATA interface 549 * @adev: Device being configured 550 * 551 * Set up the channel for MWDMA or UDMA modes. 552 */ 553 554 static void hpt372_set_dmamode(struct ata_port *ap, struct ata_device *adev) 555 { 556 hpt372_set_mode(ap, adev, adev->dma_mode); 557 } 558 559 /** 560 * hpt37x_bmdma_stop - DMA engine stop 561 * @qc: ATA command 562 * 563 * Clean up after the HPT372 and later DMA engine 564 */ 565 566 static void hpt37x_bmdma_stop(struct ata_queued_cmd *qc) 567 { 568 struct ata_port *ap = qc->ap; 569 struct pci_dev *pdev = to_pci_dev(ap->host->dev); 570 int mscreg = 0x50 + 4 * ap->port_no; 571 u8 bwsr_stat, msc_stat; 572 573 pci_read_config_byte(pdev, 0x6A, &bwsr_stat); 574 pci_read_config_byte(pdev, mscreg, &msc_stat); 575 if (bwsr_stat & (1 << ap->port_no)) 576 pci_write_config_byte(pdev, mscreg, msc_stat | 0x30); 577 ata_bmdma_stop(qc); 578 } 579 580 581 static struct scsi_host_template hpt37x_sht = { 582 ATA_BMDMA_SHT(DRV_NAME), 583 }; 584 585 /* 586 * Configuration for HPT370 587 */ 588 589 static struct ata_port_operations hpt370_port_ops = { 590 .inherits = &ata_bmdma_port_ops, 591 592 .bmdma_stop = hpt370_bmdma_stop, 593 594 .mode_filter = hpt370_filter, 595 .cable_detect = hpt37x_cable_detect, 596 .set_piomode = hpt370_set_piomode, 597 .set_dmamode = hpt370_set_dmamode, 598 .prereset = hpt37x_pre_reset, 599 }; 600 601 /* 602 * Configuration for HPT370A. Close to 370 but less filters 603 */ 604 605 static struct ata_port_operations hpt370a_port_ops = { 606 .inherits = &hpt370_port_ops, 607 .mode_filter = hpt370a_filter, 608 }; 609 610 /* 611 * Configuration for HPT371 and HPT302. Slightly different PIO and DMA 612 * mode setting functionality. 613 */ 614 615 static struct ata_port_operations hpt302_port_ops = { 616 .inherits = &ata_bmdma_port_ops, 617 618 .bmdma_stop = hpt37x_bmdma_stop, 619 620 .cable_detect = hpt37x_cable_detect, 621 .set_piomode = hpt372_set_piomode, 622 .set_dmamode = hpt372_set_dmamode, 623 .prereset = hpt37x_pre_reset, 624 }; 625 626 /* 627 * Configuration for HPT372. Mode setting works like 371 and 302 628 * but we have a mode filter. 629 */ 630 631 static struct ata_port_operations hpt372_port_ops = { 632 .inherits = &hpt302_port_ops, 633 .mode_filter = hpt372_filter, 634 }; 635 636 /* 637 * Configuration for HPT374. Mode setting and filtering works like 372 638 * but we have a different cable detection procedure for function 1. 639 */ 640 641 static struct ata_port_operations hpt374_fn1_port_ops = { 642 .inherits = &hpt372_port_ops, 643 .cable_detect = hpt374_fn1_cable_detect, 644 }; 645 646 /** 647 * hpt37x_clock_slot - Turn timing to PC clock entry 648 * @freq: Reported frequency timing 649 * @base: Base timing 650 * 651 * Turn the timing data intoa clock slot (0 for 33, 1 for 40, 2 for 50 652 * and 3 for 66Mhz) 653 */ 654 655 static int hpt37x_clock_slot(unsigned int freq, unsigned int base) 656 { 657 unsigned int f = (base * freq) / 192; /* Mhz */ 658 if (f < 40) 659 return 0; /* 33Mhz slot */ 660 if (f < 45) 661 return 1; /* 40Mhz slot */ 662 if (f < 55) 663 return 2; /* 50Mhz slot */ 664 return 3; /* 60Mhz slot */ 665 } 666 667 /** 668 * hpt37x_calibrate_dpll - Calibrate the DPLL loop 669 * @dev: PCI device 670 * 671 * Perform a calibration cycle on the HPT37x DPLL. Returns 1 if this 672 * succeeds 673 */ 674 675 static int hpt37x_calibrate_dpll(struct pci_dev *dev) 676 { 677 u8 reg5b; 678 u32 reg5c; 679 int tries; 680 681 for (tries = 0; tries < 0x5000; tries++) { 682 udelay(50); 683 pci_read_config_byte(dev, 0x5b, ®5b); 684 if (reg5b & 0x80) { 685 /* See if it stays set */ 686 for (tries = 0; tries < 0x1000; tries++) { 687 pci_read_config_byte(dev, 0x5b, ®5b); 688 /* Failed ? */ 689 if ((reg5b & 0x80) == 0) 690 return 0; 691 } 692 /* Turn off tuning, we have the DPLL set */ 693 pci_read_config_dword(dev, 0x5c, ®5c); 694 pci_write_config_dword(dev, 0x5c, reg5c & ~0x100); 695 return 1; 696 } 697 } 698 /* Never went stable */ 699 return 0; 700 } 701 702 static u32 hpt374_read_freq(struct pci_dev *pdev) 703 { 704 u32 freq; 705 unsigned long io_base = pci_resource_start(pdev, 4); 706 707 if (PCI_FUNC(pdev->devfn) & 1) { 708 struct pci_dev *pdev_0; 709 710 pdev_0 = pci_get_slot(pdev->bus, pdev->devfn - 1); 711 /* Someone hot plugged the controller on us ? */ 712 if (pdev_0 == NULL) 713 return 0; 714 io_base = pci_resource_start(pdev_0, 4); 715 freq = inl(io_base + 0x90); 716 pci_dev_put(pdev_0); 717 } else 718 freq = inl(io_base + 0x90); 719 return freq; 720 } 721 722 /** 723 * hpt37x_init_one - Initialise an HPT37X/302 724 * @dev: PCI device 725 * @id: Entry in match table 726 * 727 * Initialise an HPT37x device. There are some interesting complications 728 * here. Firstly the chip may report 366 and be one of several variants. 729 * Secondly all the timings depend on the clock for the chip which we must 730 * detect and look up 731 * 732 * This is the known chip mappings. It may be missing a couple of later 733 * releases. 734 * 735 * Chip version PCI Rev Notes 736 * HPT366 4 (HPT366) 0 Other driver 737 * HPT366 4 (HPT366) 1 Other driver 738 * HPT368 4 (HPT366) 2 Other driver 739 * HPT370 4 (HPT366) 3 UDMA100 740 * HPT370A 4 (HPT366) 4 UDMA100 741 * HPT372 4 (HPT366) 5 UDMA133 (1) 742 * HPT372N 4 (HPT366) 6 Other driver 743 * HPT372A 5 (HPT372) 1 UDMA133 (1) 744 * HPT372N 5 (HPT372) 2 Other driver 745 * HPT302 6 (HPT302) 1 UDMA133 746 * HPT302N 6 (HPT302) 2 Other driver 747 * HPT371 7 (HPT371) * UDMA133 748 * HPT374 8 (HPT374) * UDMA133 4 channel 749 * HPT372N 9 (HPT372N) * Other driver 750 * 751 * (1) UDMA133 support depends on the bus clock 752 */ 753 754 static int hpt37x_init_one(struct pci_dev *dev, const struct pci_device_id *id) 755 { 756 /* HPT370 - UDMA100 */ 757 static const struct ata_port_info info_hpt370 = { 758 .flags = ATA_FLAG_SLAVE_POSS, 759 .pio_mask = ATA_PIO4, 760 .mwdma_mask = ATA_MWDMA2, 761 .udma_mask = ATA_UDMA5, 762 .port_ops = &hpt370_port_ops 763 }; 764 /* HPT370A - UDMA100 */ 765 static const struct ata_port_info info_hpt370a = { 766 .flags = ATA_FLAG_SLAVE_POSS, 767 .pio_mask = ATA_PIO4, 768 .mwdma_mask = ATA_MWDMA2, 769 .udma_mask = ATA_UDMA5, 770 .port_ops = &hpt370a_port_ops 771 }; 772 /* HPT370 - UDMA66 */ 773 static const struct ata_port_info info_hpt370_33 = { 774 .flags = ATA_FLAG_SLAVE_POSS, 775 .pio_mask = ATA_PIO4, 776 .mwdma_mask = ATA_MWDMA2, 777 .udma_mask = ATA_UDMA4, 778 .port_ops = &hpt370_port_ops 779 }; 780 /* HPT370A - UDMA66 */ 781 static const struct ata_port_info info_hpt370a_33 = { 782 .flags = ATA_FLAG_SLAVE_POSS, 783 .pio_mask = ATA_PIO4, 784 .mwdma_mask = ATA_MWDMA2, 785 .udma_mask = ATA_UDMA4, 786 .port_ops = &hpt370a_port_ops 787 }; 788 /* HPT372 - UDMA133 */ 789 static const struct ata_port_info info_hpt372 = { 790 .flags = ATA_FLAG_SLAVE_POSS, 791 .pio_mask = ATA_PIO4, 792 .mwdma_mask = ATA_MWDMA2, 793 .udma_mask = ATA_UDMA6, 794 .port_ops = &hpt372_port_ops 795 }; 796 /* HPT371, 302 - UDMA133 */ 797 static const struct ata_port_info info_hpt302 = { 798 .flags = ATA_FLAG_SLAVE_POSS, 799 .pio_mask = ATA_PIO4, 800 .mwdma_mask = ATA_MWDMA2, 801 .udma_mask = ATA_UDMA6, 802 .port_ops = &hpt302_port_ops 803 }; 804 /* HPT374 - UDMA100, function 1 uses different cable_detect method */ 805 static const struct ata_port_info info_hpt374_fn0 = { 806 .flags = ATA_FLAG_SLAVE_POSS, 807 .pio_mask = ATA_PIO4, 808 .mwdma_mask = ATA_MWDMA2, 809 .udma_mask = ATA_UDMA5, 810 .port_ops = &hpt372_port_ops 811 }; 812 static const struct ata_port_info info_hpt374_fn1 = { 813 .flags = ATA_FLAG_SLAVE_POSS, 814 .pio_mask = ATA_PIO4, 815 .mwdma_mask = ATA_MWDMA2, 816 .udma_mask = ATA_UDMA5, 817 .port_ops = &hpt374_fn1_port_ops 818 }; 819 820 static const int MHz[4] = { 33, 40, 50, 66 }; 821 void *private_data = NULL; 822 const struct ata_port_info *ppi[] = { NULL, NULL }; 823 u8 rev = dev->revision; 824 u8 irqmask; 825 u8 mcr1; 826 u32 freq; 827 int prefer_dpll = 1; 828 829 unsigned long iobase = pci_resource_start(dev, 4); 830 831 const struct hpt_chip *chip_table; 832 int clock_slot; 833 int rc; 834 835 rc = pcim_enable_device(dev); 836 if (rc) 837 return rc; 838 839 switch (dev->device) { 840 case PCI_DEVICE_ID_TTI_HPT366: 841 /* May be a later chip in disguise. Check */ 842 /* Older chips are in the HPT366 driver. Ignore them */ 843 if (rev < 3) 844 return -ENODEV; 845 /* N series chips have their own driver. Ignore */ 846 if (rev == 6) 847 return -ENODEV; 848 849 switch (rev) { 850 case 3: 851 ppi[0] = &info_hpt370; 852 chip_table = &hpt370; 853 prefer_dpll = 0; 854 break; 855 case 4: 856 ppi[0] = &info_hpt370a; 857 chip_table = &hpt370a; 858 prefer_dpll = 0; 859 break; 860 case 5: 861 ppi[0] = &info_hpt372; 862 chip_table = &hpt372; 863 break; 864 default: 865 dev_err(&dev->dev, 866 "Unknown HPT366 subtype, please report (%d)\n", 867 rev); 868 return -ENODEV; 869 } 870 break; 871 case PCI_DEVICE_ID_TTI_HPT372: 872 /* 372N if rev >= 2 */ 873 if (rev >= 2) 874 return -ENODEV; 875 ppi[0] = &info_hpt372; 876 chip_table = &hpt372a; 877 break; 878 case PCI_DEVICE_ID_TTI_HPT302: 879 /* 302N if rev > 1 */ 880 if (rev > 1) 881 return -ENODEV; 882 ppi[0] = &info_hpt302; 883 /* Check this */ 884 chip_table = &hpt302; 885 break; 886 case PCI_DEVICE_ID_TTI_HPT371: 887 if (rev > 1) 888 return -ENODEV; 889 ppi[0] = &info_hpt302; 890 chip_table = &hpt371; 891 /* 892 * Single channel device, master is not present but the BIOS 893 * (or us for non x86) must mark it absent 894 */ 895 pci_read_config_byte(dev, 0x50, &mcr1); 896 mcr1 &= ~0x04; 897 pci_write_config_byte(dev, 0x50, mcr1); 898 break; 899 case PCI_DEVICE_ID_TTI_HPT374: 900 chip_table = &hpt374; 901 if (!(PCI_FUNC(dev->devfn) & 1)) 902 *ppi = &info_hpt374_fn0; 903 else 904 *ppi = &info_hpt374_fn1; 905 break; 906 default: 907 dev_err(&dev->dev, "PCI table is bogus, please report (%d)\n", 908 dev->device); 909 return -ENODEV; 910 } 911 /* Ok so this is a chip we support */ 912 913 pci_write_config_byte(dev, PCI_CACHE_LINE_SIZE, (L1_CACHE_BYTES / 4)); 914 pci_write_config_byte(dev, PCI_LATENCY_TIMER, 0x78); 915 pci_write_config_byte(dev, PCI_MIN_GNT, 0x08); 916 pci_write_config_byte(dev, PCI_MAX_LAT, 0x08); 917 918 pci_read_config_byte(dev, 0x5A, &irqmask); 919 irqmask &= ~0x10; 920 pci_write_config_byte(dev, 0x5a, irqmask); 921 922 /* 923 * default to pci clock. make sure MA15/16 are set to output 924 * to prevent drives having problems with 40-pin cables. Needed 925 * for some drives such as IBM-DTLA which will not enter ready 926 * state on reset when PDIAG is a input. 927 */ 928 929 pci_write_config_byte(dev, 0x5b, 0x23); 930 931 /* 932 * HighPoint does this for HPT372A. 933 * NOTE: This register is only writeable via I/O space. 934 */ 935 if (chip_table == &hpt372a) 936 outb(0x0e, iobase + 0x9c); 937 938 /* 939 * Some devices do not let this value be accessed via PCI space 940 * according to the old driver. In addition we must use the value 941 * from FN 0 on the HPT374. 942 */ 943 944 if (chip_table == &hpt374) { 945 freq = hpt374_read_freq(dev); 946 if (freq == 0) 947 return -ENODEV; 948 } else 949 freq = inl(iobase + 0x90); 950 951 if ((freq >> 12) != 0xABCDE) { 952 int i; 953 u8 sr; 954 u32 total = 0; 955 956 dev_warn(&dev->dev, "BIOS has not set timing clocks\n"); 957 958 /* This is the process the HPT371 BIOS is reported to use */ 959 for (i = 0; i < 128; i++) { 960 pci_read_config_byte(dev, 0x78, &sr); 961 total += sr & 0x1FF; 962 udelay(15); 963 } 964 freq = total / 128; 965 } 966 freq &= 0x1FF; 967 968 /* 969 * Turn the frequency check into a band and then find a timing 970 * table to match it. 971 */ 972 973 clock_slot = hpt37x_clock_slot(freq, chip_table->base); 974 if (chip_table->clocks[clock_slot] == NULL || prefer_dpll) { 975 /* 976 * We need to try PLL mode instead 977 * 978 * For non UDMA133 capable devices we should 979 * use a 50MHz DPLL by choice 980 */ 981 unsigned int f_low, f_high; 982 int dpll, adjust; 983 984 /* Compute DPLL */ 985 dpll = (ppi[0]->udma_mask & 0xC0) ? 3 : 2; 986 987 f_low = (MHz[clock_slot] * 48) / MHz[dpll]; 988 f_high = f_low + 2; 989 if (clock_slot > 1) 990 f_high += 2; 991 992 /* Select the DPLL clock. */ 993 pci_write_config_byte(dev, 0x5b, 0x21); 994 pci_write_config_dword(dev, 0x5C, 995 (f_high << 16) | f_low | 0x100); 996 997 for (adjust = 0; adjust < 8; adjust++) { 998 if (hpt37x_calibrate_dpll(dev)) 999 break; 1000 /* 1001 * See if it'll settle at a fractionally 1002 * different clock 1003 */ 1004 if (adjust & 1) 1005 f_low -= adjust >> 1; 1006 else 1007 f_high += adjust >> 1; 1008 pci_write_config_dword(dev, 0x5C, 1009 (f_high << 16) | f_low | 0x100); 1010 } 1011 if (adjust == 8) { 1012 dev_err(&dev->dev, "DPLL did not stabilize!\n"); 1013 return -ENODEV; 1014 } 1015 if (dpll == 3) 1016 private_data = (void *)hpt37x_timings_66; 1017 else 1018 private_data = (void *)hpt37x_timings_50; 1019 1020 dev_info(&dev->dev, "bus clock %dMHz, using %dMHz DPLL\n", 1021 MHz[clock_slot], MHz[dpll]); 1022 } else { 1023 private_data = (void *)chip_table->clocks[clock_slot]; 1024 /* 1025 * Perform a final fixup. Note that we will have used the 1026 * DPLL on the HPT372 which means we don't have to worry 1027 * about lack of UDMA133 support on lower clocks 1028 */ 1029 1030 if (clock_slot < 2 && ppi[0] == &info_hpt370) 1031 ppi[0] = &info_hpt370_33; 1032 if (clock_slot < 2 && ppi[0] == &info_hpt370a) 1033 ppi[0] = &info_hpt370a_33; 1034 1035 dev_info(&dev->dev, "%s using %dMHz bus clock\n", 1036 chip_table->name, MHz[clock_slot]); 1037 } 1038 1039 /* Now kick off ATA set up */ 1040 return ata_pci_bmdma_init_one(dev, ppi, &hpt37x_sht, private_data, 0); 1041 } 1042 1043 static const struct pci_device_id hpt37x[] = { 1044 { PCI_VDEVICE(TTI, PCI_DEVICE_ID_TTI_HPT366), }, 1045 { PCI_VDEVICE(TTI, PCI_DEVICE_ID_TTI_HPT371), }, 1046 { PCI_VDEVICE(TTI, PCI_DEVICE_ID_TTI_HPT372), }, 1047 { PCI_VDEVICE(TTI, PCI_DEVICE_ID_TTI_HPT374), }, 1048 { PCI_VDEVICE(TTI, PCI_DEVICE_ID_TTI_HPT302), }, 1049 1050 { }, 1051 }; 1052 1053 static struct pci_driver hpt37x_pci_driver = { 1054 .name = DRV_NAME, 1055 .id_table = hpt37x, 1056 .probe = hpt37x_init_one, 1057 .remove = ata_pci_remove_one 1058 }; 1059 1060 module_pci_driver(hpt37x_pci_driver); 1061 1062 MODULE_AUTHOR("Alan Cox"); 1063 MODULE_DESCRIPTION("low-level driver for the Highpoint HPT37x/30x"); 1064 MODULE_LICENSE("GPL"); 1065 MODULE_DEVICE_TABLE(pci, hpt37x); 1066 MODULE_VERSION(DRV_VERSION); 1067