1 /* 2 * Libata driver for the highpoint 37x and 30x UDMA66 ATA controllers. 3 * 4 * This driver is heavily based upon: 5 * 6 * linux/drivers/ide/pci/hpt366.c Version 0.36 April 25, 2003 7 * 8 * Copyright (C) 1999-2003 Andre Hedrick <andre@linux-ide.org> 9 * Portions Copyright (C) 2001 Sun Microsystems, Inc. 10 * Portions Copyright (C) 2003 Red Hat Inc 11 * Portions Copyright (C) 2005-2010 MontaVista Software, Inc. 12 * 13 * TODO 14 * Look into engine reset on timeout errors. Should not be required. 15 */ 16 17 #define pr_fmt(fmt) KBUILD_MODNAME ": " fmt 18 19 #include <linux/kernel.h> 20 #include <linux/module.h> 21 #include <linux/pci.h> 22 #include <linux/blkdev.h> 23 #include <linux/delay.h> 24 #include <scsi/scsi_host.h> 25 #include <linux/libata.h> 26 27 #define DRV_NAME "pata_hpt37x" 28 #define DRV_VERSION "0.6.23" 29 30 struct hpt_clock { 31 u8 xfer_speed; 32 u32 timing; 33 }; 34 35 struct hpt_chip { 36 const char *name; 37 unsigned int base; 38 struct hpt_clock const *clocks[4]; 39 }; 40 41 /* key for bus clock timings 42 * bit 43 * 0:3 data_high_time. Inactive time of DIOW_/DIOR_ for PIO and MW DMA. 44 * cycles = value + 1 45 * 4:8 data_low_time. Active time of DIOW_/DIOR_ for PIO and MW DMA. 46 * cycles = value + 1 47 * 9:12 cmd_high_time. Inactive time of DIOW_/DIOR_ during task file 48 * register access. 49 * 13:17 cmd_low_time. Active time of DIOW_/DIOR_ during task file 50 * register access. 51 * 18:20 udma_cycle_time. Clock cycles for UDMA xfer. 52 * 21 CLK frequency for UDMA: 0=ATA clock, 1=dual ATA clock. 53 * 22:24 pre_high_time. Time to initialize 1st cycle for PIO and MW DMA xfer. 54 * 25:27 cmd_pre_high_time. Time to initialize 1st PIO cycle for task file 55 * register access. 56 * 28 UDMA enable. 57 * 29 DMA enable. 58 * 30 PIO_MST enable. If set, the chip is in bus master mode during 59 * PIO xfer. 60 * 31 FIFO enable. Only for PIO. 61 */ 62 63 static struct hpt_clock hpt37x_timings_33[] = { 64 { XFER_UDMA_6, 0x12446231 }, /* 0x12646231 ?? */ 65 { XFER_UDMA_5, 0x12446231 }, 66 { XFER_UDMA_4, 0x12446231 }, 67 { XFER_UDMA_3, 0x126c6231 }, 68 { XFER_UDMA_2, 0x12486231 }, 69 { XFER_UDMA_1, 0x124c6233 }, 70 { XFER_UDMA_0, 0x12506297 }, 71 72 { XFER_MW_DMA_2, 0x22406c31 }, 73 { XFER_MW_DMA_1, 0x22406c33 }, 74 { XFER_MW_DMA_0, 0x22406c97 }, 75 76 { XFER_PIO_4, 0x06414e31 }, 77 { XFER_PIO_3, 0x06414e42 }, 78 { XFER_PIO_2, 0x06414e53 }, 79 { XFER_PIO_1, 0x06814e93 }, 80 { XFER_PIO_0, 0x06814ea7 } 81 }; 82 83 static struct hpt_clock hpt37x_timings_50[] = { 84 { XFER_UDMA_6, 0x12848242 }, 85 { XFER_UDMA_5, 0x12848242 }, 86 { XFER_UDMA_4, 0x12ac8242 }, 87 { XFER_UDMA_3, 0x128c8242 }, 88 { XFER_UDMA_2, 0x120c8242 }, 89 { XFER_UDMA_1, 0x12148254 }, 90 { XFER_UDMA_0, 0x121882ea }, 91 92 { XFER_MW_DMA_2, 0x22808242 }, 93 { XFER_MW_DMA_1, 0x22808254 }, 94 { XFER_MW_DMA_0, 0x228082ea }, 95 96 { XFER_PIO_4, 0x0a81f442 }, 97 { XFER_PIO_3, 0x0a81f443 }, 98 { XFER_PIO_2, 0x0a81f454 }, 99 { XFER_PIO_1, 0x0ac1f465 }, 100 { XFER_PIO_0, 0x0ac1f48a } 101 }; 102 103 static struct hpt_clock hpt37x_timings_66[] = { 104 { XFER_UDMA_6, 0x1c869c62 }, 105 { XFER_UDMA_5, 0x1cae9c62 }, /* 0x1c8a9c62 */ 106 { XFER_UDMA_4, 0x1c8a9c62 }, 107 { XFER_UDMA_3, 0x1c8e9c62 }, 108 { XFER_UDMA_2, 0x1c929c62 }, 109 { XFER_UDMA_1, 0x1c9a9c62 }, 110 { XFER_UDMA_0, 0x1c829c62 }, 111 112 { XFER_MW_DMA_2, 0x2c829c62 }, 113 { XFER_MW_DMA_1, 0x2c829c66 }, 114 { XFER_MW_DMA_0, 0x2c829d2e }, 115 116 { XFER_PIO_4, 0x0c829c62 }, 117 { XFER_PIO_3, 0x0c829c84 }, 118 { XFER_PIO_2, 0x0c829ca6 }, 119 { XFER_PIO_1, 0x0d029d26 }, 120 { XFER_PIO_0, 0x0d029d5e } 121 }; 122 123 124 static const struct hpt_chip hpt370 = { 125 "HPT370", 126 48, 127 { 128 hpt37x_timings_33, 129 NULL, 130 NULL, 131 NULL 132 } 133 }; 134 135 static const struct hpt_chip hpt370a = { 136 "HPT370A", 137 48, 138 { 139 hpt37x_timings_33, 140 NULL, 141 hpt37x_timings_50, 142 NULL 143 } 144 }; 145 146 static const struct hpt_chip hpt372 = { 147 "HPT372", 148 55, 149 { 150 hpt37x_timings_33, 151 NULL, 152 hpt37x_timings_50, 153 hpt37x_timings_66 154 } 155 }; 156 157 static const struct hpt_chip hpt302 = { 158 "HPT302", 159 66, 160 { 161 hpt37x_timings_33, 162 NULL, 163 hpt37x_timings_50, 164 hpt37x_timings_66 165 } 166 }; 167 168 static const struct hpt_chip hpt371 = { 169 "HPT371", 170 66, 171 { 172 hpt37x_timings_33, 173 NULL, 174 hpt37x_timings_50, 175 hpt37x_timings_66 176 } 177 }; 178 179 static const struct hpt_chip hpt372a = { 180 "HPT372A", 181 66, 182 { 183 hpt37x_timings_33, 184 NULL, 185 hpt37x_timings_50, 186 hpt37x_timings_66 187 } 188 }; 189 190 static const struct hpt_chip hpt374 = { 191 "HPT374", 192 48, 193 { 194 hpt37x_timings_33, 195 NULL, 196 NULL, 197 NULL 198 } 199 }; 200 201 /** 202 * hpt37x_find_mode - reset the hpt37x bus 203 * @ap: ATA port 204 * @speed: transfer mode 205 * 206 * Return the 32bit register programming information for this channel 207 * that matches the speed provided. 208 */ 209 210 static u32 hpt37x_find_mode(struct ata_port *ap, int speed) 211 { 212 struct hpt_clock *clocks = ap->host->private_data; 213 214 while (clocks->xfer_speed) { 215 if (clocks->xfer_speed == speed) 216 return clocks->timing; 217 clocks++; 218 } 219 BUG(); 220 return 0xffffffffU; /* silence compiler warning */ 221 } 222 223 static int hpt_dma_blacklisted(const struct ata_device *dev, char *modestr, 224 const char * const list[]) 225 { 226 unsigned char model_num[ATA_ID_PROD_LEN + 1]; 227 int i; 228 229 ata_id_c_string(dev->id, model_num, ATA_ID_PROD, sizeof(model_num)); 230 231 i = match_string(list, -1, model_num); 232 if (i >= 0) { 233 pr_warn("%s is not supported for %s\n", modestr, list[i]); 234 return 1; 235 } 236 return 0; 237 } 238 239 static const char * const bad_ata33[] = { 240 "Maxtor 92720U8", "Maxtor 92040U6", "Maxtor 91360U4", "Maxtor 91020U3", 241 "Maxtor 90845U3", "Maxtor 90650U2", 242 "Maxtor 91360D8", "Maxtor 91190D7", "Maxtor 91020D6", "Maxtor 90845D5", 243 "Maxtor 90680D4", "Maxtor 90510D3", "Maxtor 90340D2", 244 "Maxtor 91152D8", "Maxtor 91008D7", "Maxtor 90845D6", "Maxtor 90840D6", 245 "Maxtor 90720D5", "Maxtor 90648D5", "Maxtor 90576D4", 246 "Maxtor 90510D4", 247 "Maxtor 90432D3", "Maxtor 90288D2", "Maxtor 90256D2", 248 "Maxtor 91000D8", "Maxtor 90910D8", "Maxtor 90875D7", "Maxtor 90840D7", 249 "Maxtor 90750D6", "Maxtor 90625D5", "Maxtor 90500D4", 250 "Maxtor 91728D8", "Maxtor 91512D7", "Maxtor 91303D6", "Maxtor 91080D5", 251 "Maxtor 90845D4", "Maxtor 90680D4", "Maxtor 90648D3", "Maxtor 90432D2", 252 NULL 253 }; 254 255 static const char * const bad_ata100_5[] = { 256 "IBM-DTLA-307075", 257 "IBM-DTLA-307060", 258 "IBM-DTLA-307045", 259 "IBM-DTLA-307030", 260 "IBM-DTLA-307020", 261 "IBM-DTLA-307015", 262 "IBM-DTLA-305040", 263 "IBM-DTLA-305030", 264 "IBM-DTLA-305020", 265 "IC35L010AVER07-0", 266 "IC35L020AVER07-0", 267 "IC35L030AVER07-0", 268 "IC35L040AVER07-0", 269 "IC35L060AVER07-0", 270 "WDC AC310200R", 271 NULL 272 }; 273 274 /** 275 * hpt370_filter - mode selection filter 276 * @adev: ATA device 277 * 278 * Block UDMA on devices that cause trouble with this controller. 279 */ 280 281 static unsigned long hpt370_filter(struct ata_device *adev, unsigned long mask) 282 { 283 if (adev->class == ATA_DEV_ATA) { 284 if (hpt_dma_blacklisted(adev, "UDMA", bad_ata33)) 285 mask &= ~ATA_MASK_UDMA; 286 if (hpt_dma_blacklisted(adev, "UDMA100", bad_ata100_5)) 287 mask &= ~(0xE0 << ATA_SHIFT_UDMA); 288 } 289 return mask; 290 } 291 292 /** 293 * hpt370a_filter - mode selection filter 294 * @adev: ATA device 295 * 296 * Block UDMA on devices that cause trouble with this controller. 297 */ 298 299 static unsigned long hpt370a_filter(struct ata_device *adev, unsigned long mask) 300 { 301 if (adev->class == ATA_DEV_ATA) { 302 if (hpt_dma_blacklisted(adev, "UDMA100", bad_ata100_5)) 303 mask &= ~(0xE0 << ATA_SHIFT_UDMA); 304 } 305 return mask; 306 } 307 308 /** 309 * hpt372_filter - mode selection filter 310 * @adev: ATA device 311 * @mask: mode mask 312 * 313 * The Marvell bridge chips used on the HighPoint SATA cards do not seem 314 * to support the UltraDMA modes 1, 2, and 3 as well as any MWDMA modes... 315 */ 316 static unsigned long hpt372_filter(struct ata_device *adev, unsigned long mask) 317 { 318 if (ata_id_is_sata(adev->id)) 319 mask &= ~((0xE << ATA_SHIFT_UDMA) | ATA_MASK_MWDMA); 320 321 return mask; 322 } 323 324 /** 325 * hpt37x_cable_detect - Detect the cable type 326 * @ap: ATA port to detect on 327 * 328 * Return the cable type attached to this port 329 */ 330 331 static int hpt37x_cable_detect(struct ata_port *ap) 332 { 333 struct pci_dev *pdev = to_pci_dev(ap->host->dev); 334 u8 scr2, ata66; 335 336 pci_read_config_byte(pdev, 0x5B, &scr2); 337 pci_write_config_byte(pdev, 0x5B, scr2 & ~0x01); 338 339 udelay(10); /* debounce */ 340 341 /* Cable register now active */ 342 pci_read_config_byte(pdev, 0x5A, &ata66); 343 /* Restore state */ 344 pci_write_config_byte(pdev, 0x5B, scr2); 345 346 if (ata66 & (2 >> ap->port_no)) 347 return ATA_CBL_PATA40; 348 else 349 return ATA_CBL_PATA80; 350 } 351 352 /** 353 * hpt374_fn1_cable_detect - Detect the cable type 354 * @ap: ATA port to detect on 355 * 356 * Return the cable type attached to this port 357 */ 358 359 static int hpt374_fn1_cable_detect(struct ata_port *ap) 360 { 361 struct pci_dev *pdev = to_pci_dev(ap->host->dev); 362 unsigned int mcrbase = 0x50 + 4 * ap->port_no; 363 u16 mcr3; 364 u8 ata66; 365 366 /* Do the extra channel work */ 367 pci_read_config_word(pdev, mcrbase + 2, &mcr3); 368 /* Set bit 15 of 0x52 to enable TCBLID as input */ 369 pci_write_config_word(pdev, mcrbase + 2, mcr3 | 0x8000); 370 pci_read_config_byte(pdev, 0x5A, &ata66); 371 /* Reset TCBLID/FCBLID to output */ 372 pci_write_config_word(pdev, mcrbase + 2, mcr3); 373 374 if (ata66 & (2 >> ap->port_no)) 375 return ATA_CBL_PATA40; 376 else 377 return ATA_CBL_PATA80; 378 } 379 380 /** 381 * hpt37x_pre_reset - reset the hpt37x bus 382 * @link: ATA link to reset 383 * @deadline: deadline jiffies for the operation 384 * 385 * Perform the initial reset handling for the HPT37x. 386 */ 387 388 static int hpt37x_pre_reset(struct ata_link *link, unsigned long deadline) 389 { 390 struct ata_port *ap = link->ap; 391 struct pci_dev *pdev = to_pci_dev(ap->host->dev); 392 static const struct pci_bits hpt37x_enable_bits[] = { 393 { 0x50, 1, 0x04, 0x04 }, 394 { 0x54, 1, 0x04, 0x04 } 395 }; 396 397 if (!pci_test_config_bits(pdev, &hpt37x_enable_bits[ap->port_no])) 398 return -ENOENT; 399 400 /* Reset the state machine */ 401 pci_write_config_byte(pdev, 0x50 + 4 * ap->port_no, 0x37); 402 udelay(100); 403 404 return ata_sff_prereset(link, deadline); 405 } 406 407 static void hpt370_set_mode(struct ata_port *ap, struct ata_device *adev, 408 u8 mode) 409 { 410 struct pci_dev *pdev = to_pci_dev(ap->host->dev); 411 u32 addr1, addr2; 412 u32 reg, timing, mask; 413 u8 fast; 414 415 addr1 = 0x40 + 4 * (adev->devno + 2 * ap->port_no); 416 addr2 = 0x51 + 4 * ap->port_no; 417 418 /* Fast interrupt prediction disable, hold off interrupt disable */ 419 pci_read_config_byte(pdev, addr2, &fast); 420 fast &= ~0x02; 421 fast |= 0x01; 422 pci_write_config_byte(pdev, addr2, fast); 423 424 /* Determine timing mask and find matching mode entry */ 425 if (mode < XFER_MW_DMA_0) 426 mask = 0xcfc3ffff; 427 else if (mode < XFER_UDMA_0) 428 mask = 0x31c001ff; 429 else 430 mask = 0x303c0000; 431 432 timing = hpt37x_find_mode(ap, mode); 433 434 pci_read_config_dword(pdev, addr1, ®); 435 reg = (reg & ~mask) | (timing & mask); 436 pci_write_config_dword(pdev, addr1, reg); 437 } 438 /** 439 * hpt370_set_piomode - PIO setup 440 * @ap: ATA interface 441 * @adev: device on the interface 442 * 443 * Perform PIO mode setup. 444 */ 445 446 static void hpt370_set_piomode(struct ata_port *ap, struct ata_device *adev) 447 { 448 hpt370_set_mode(ap, adev, adev->pio_mode); 449 } 450 451 /** 452 * hpt370_set_dmamode - DMA timing setup 453 * @ap: ATA interface 454 * @adev: Device being configured 455 * 456 * Set up the channel for MWDMA or UDMA modes. 457 */ 458 459 static void hpt370_set_dmamode(struct ata_port *ap, struct ata_device *adev) 460 { 461 hpt370_set_mode(ap, adev, adev->dma_mode); 462 } 463 464 /** 465 * hpt370_bmdma_end - DMA engine stop 466 * @qc: ATA command 467 * 468 * Work around the HPT370 DMA engine. 469 */ 470 471 static void hpt370_bmdma_stop(struct ata_queued_cmd *qc) 472 { 473 struct ata_port *ap = qc->ap; 474 struct pci_dev *pdev = to_pci_dev(ap->host->dev); 475 void __iomem *bmdma = ap->ioaddr.bmdma_addr; 476 u8 dma_stat = ioread8(bmdma + ATA_DMA_STATUS); 477 u8 dma_cmd; 478 479 if (dma_stat & ATA_DMA_ACTIVE) { 480 udelay(20); 481 dma_stat = ioread8(bmdma + ATA_DMA_STATUS); 482 } 483 if (dma_stat & ATA_DMA_ACTIVE) { 484 /* Clear the engine */ 485 pci_write_config_byte(pdev, 0x50 + 4 * ap->port_no, 0x37); 486 udelay(10); 487 /* Stop DMA */ 488 dma_cmd = ioread8(bmdma + ATA_DMA_CMD); 489 iowrite8(dma_cmd & ~ATA_DMA_START, bmdma + ATA_DMA_CMD); 490 /* Clear Error */ 491 dma_stat = ioread8(bmdma + ATA_DMA_STATUS); 492 iowrite8(dma_stat | ATA_DMA_INTR | ATA_DMA_ERR, 493 bmdma + ATA_DMA_STATUS); 494 /* Clear the engine */ 495 pci_write_config_byte(pdev, 0x50 + 4 * ap->port_no, 0x37); 496 udelay(10); 497 } 498 ata_bmdma_stop(qc); 499 } 500 501 static void hpt372_set_mode(struct ata_port *ap, struct ata_device *adev, 502 u8 mode) 503 { 504 struct pci_dev *pdev = to_pci_dev(ap->host->dev); 505 u32 addr1, addr2; 506 u32 reg, timing, mask; 507 u8 fast; 508 509 addr1 = 0x40 + 4 * (adev->devno + 2 * ap->port_no); 510 addr2 = 0x51 + 4 * ap->port_no; 511 512 /* Fast interrupt prediction disable, hold off interrupt disable */ 513 pci_read_config_byte(pdev, addr2, &fast); 514 fast &= ~0x07; 515 pci_write_config_byte(pdev, addr2, fast); 516 517 /* Determine timing mask and find matching mode entry */ 518 if (mode < XFER_MW_DMA_0) 519 mask = 0xcfc3ffff; 520 else if (mode < XFER_UDMA_0) 521 mask = 0x31c001ff; 522 else 523 mask = 0x303c0000; 524 525 timing = hpt37x_find_mode(ap, mode); 526 527 pci_read_config_dword(pdev, addr1, ®); 528 reg = (reg & ~mask) | (timing & mask); 529 pci_write_config_dword(pdev, addr1, reg); 530 } 531 532 /** 533 * hpt372_set_piomode - PIO setup 534 * @ap: ATA interface 535 * @adev: device on the interface 536 * 537 * Perform PIO mode setup. 538 */ 539 540 static void hpt372_set_piomode(struct ata_port *ap, struct ata_device *adev) 541 { 542 hpt372_set_mode(ap, adev, adev->pio_mode); 543 } 544 545 /** 546 * hpt372_set_dmamode - DMA timing setup 547 * @ap: ATA interface 548 * @adev: Device being configured 549 * 550 * Set up the channel for MWDMA or UDMA modes. 551 */ 552 553 static void hpt372_set_dmamode(struct ata_port *ap, struct ata_device *adev) 554 { 555 hpt372_set_mode(ap, adev, adev->dma_mode); 556 } 557 558 /** 559 * hpt37x_bmdma_end - DMA engine stop 560 * @qc: ATA command 561 * 562 * Clean up after the HPT372 and later DMA engine 563 */ 564 565 static void hpt37x_bmdma_stop(struct ata_queued_cmd *qc) 566 { 567 struct ata_port *ap = qc->ap; 568 struct pci_dev *pdev = to_pci_dev(ap->host->dev); 569 int mscreg = 0x50 + 4 * ap->port_no; 570 u8 bwsr_stat, msc_stat; 571 572 pci_read_config_byte(pdev, 0x6A, &bwsr_stat); 573 pci_read_config_byte(pdev, mscreg, &msc_stat); 574 if (bwsr_stat & (1 << ap->port_no)) 575 pci_write_config_byte(pdev, mscreg, msc_stat | 0x30); 576 ata_bmdma_stop(qc); 577 } 578 579 580 static struct scsi_host_template hpt37x_sht = { 581 ATA_BMDMA_SHT(DRV_NAME), 582 }; 583 584 /* 585 * Configuration for HPT370 586 */ 587 588 static struct ata_port_operations hpt370_port_ops = { 589 .inherits = &ata_bmdma_port_ops, 590 591 .bmdma_stop = hpt370_bmdma_stop, 592 593 .mode_filter = hpt370_filter, 594 .cable_detect = hpt37x_cable_detect, 595 .set_piomode = hpt370_set_piomode, 596 .set_dmamode = hpt370_set_dmamode, 597 .prereset = hpt37x_pre_reset, 598 }; 599 600 /* 601 * Configuration for HPT370A. Close to 370 but less filters 602 */ 603 604 static struct ata_port_operations hpt370a_port_ops = { 605 .inherits = &hpt370_port_ops, 606 .mode_filter = hpt370a_filter, 607 }; 608 609 /* 610 * Configuration for HPT371 and HPT302. Slightly different PIO and DMA 611 * mode setting functionality. 612 */ 613 614 static struct ata_port_operations hpt302_port_ops = { 615 .inherits = &ata_bmdma_port_ops, 616 617 .bmdma_stop = hpt37x_bmdma_stop, 618 619 .cable_detect = hpt37x_cable_detect, 620 .set_piomode = hpt372_set_piomode, 621 .set_dmamode = hpt372_set_dmamode, 622 .prereset = hpt37x_pre_reset, 623 }; 624 625 /* 626 * Configuration for HPT372. Mode setting works like 371 and 302 627 * but we have a mode filter. 628 */ 629 630 static struct ata_port_operations hpt372_port_ops = { 631 .inherits = &hpt302_port_ops, 632 .mode_filter = hpt372_filter, 633 }; 634 635 /* 636 * Configuration for HPT374. Mode setting and filtering works like 372 637 * but we have a different cable detection procedure for function 1. 638 */ 639 640 static struct ata_port_operations hpt374_fn1_port_ops = { 641 .inherits = &hpt372_port_ops, 642 .cable_detect = hpt374_fn1_cable_detect, 643 }; 644 645 /** 646 * hpt37x_clock_slot - Turn timing to PC clock entry 647 * @freq: Reported frequency timing 648 * @base: Base timing 649 * 650 * Turn the timing data intoa clock slot (0 for 33, 1 for 40, 2 for 50 651 * and 3 for 66Mhz) 652 */ 653 654 static int hpt37x_clock_slot(unsigned int freq, unsigned int base) 655 { 656 unsigned int f = (base * freq) / 192; /* Mhz */ 657 if (f < 40) 658 return 0; /* 33Mhz slot */ 659 if (f < 45) 660 return 1; /* 40Mhz slot */ 661 if (f < 55) 662 return 2; /* 50Mhz slot */ 663 return 3; /* 60Mhz slot */ 664 } 665 666 /** 667 * hpt37x_calibrate_dpll - Calibrate the DPLL loop 668 * @dev: PCI device 669 * 670 * Perform a calibration cycle on the HPT37x DPLL. Returns 1 if this 671 * succeeds 672 */ 673 674 static int hpt37x_calibrate_dpll(struct pci_dev *dev) 675 { 676 u8 reg5b; 677 u32 reg5c; 678 int tries; 679 680 for (tries = 0; tries < 0x5000; tries++) { 681 udelay(50); 682 pci_read_config_byte(dev, 0x5b, ®5b); 683 if (reg5b & 0x80) { 684 /* See if it stays set */ 685 for (tries = 0; tries < 0x1000; tries++) { 686 pci_read_config_byte(dev, 0x5b, ®5b); 687 /* Failed ? */ 688 if ((reg5b & 0x80) == 0) 689 return 0; 690 } 691 /* Turn off tuning, we have the DPLL set */ 692 pci_read_config_dword(dev, 0x5c, ®5c); 693 pci_write_config_dword(dev, 0x5c, reg5c & ~0x100); 694 return 1; 695 } 696 } 697 /* Never went stable */ 698 return 0; 699 } 700 701 static u32 hpt374_read_freq(struct pci_dev *pdev) 702 { 703 u32 freq; 704 unsigned long io_base = pci_resource_start(pdev, 4); 705 706 if (PCI_FUNC(pdev->devfn) & 1) { 707 struct pci_dev *pdev_0; 708 709 pdev_0 = pci_get_slot(pdev->bus, pdev->devfn - 1); 710 /* Someone hot plugged the controller on us ? */ 711 if (pdev_0 == NULL) 712 return 0; 713 io_base = pci_resource_start(pdev_0, 4); 714 freq = inl(io_base + 0x90); 715 pci_dev_put(pdev_0); 716 } else 717 freq = inl(io_base + 0x90); 718 return freq; 719 } 720 721 /** 722 * hpt37x_init_one - Initialise an HPT37X/302 723 * @dev: PCI device 724 * @id: Entry in match table 725 * 726 * Initialise an HPT37x device. There are some interesting complications 727 * here. Firstly the chip may report 366 and be one of several variants. 728 * Secondly all the timings depend on the clock for the chip which we must 729 * detect and look up 730 * 731 * This is the known chip mappings. It may be missing a couple of later 732 * releases. 733 * 734 * Chip version PCI Rev Notes 735 * HPT366 4 (HPT366) 0 Other driver 736 * HPT366 4 (HPT366) 1 Other driver 737 * HPT368 4 (HPT366) 2 Other driver 738 * HPT370 4 (HPT366) 3 UDMA100 739 * HPT370A 4 (HPT366) 4 UDMA100 740 * HPT372 4 (HPT366) 5 UDMA133 (1) 741 * HPT372N 4 (HPT366) 6 Other driver 742 * HPT372A 5 (HPT372) 1 UDMA133 (1) 743 * HPT372N 5 (HPT372) 2 Other driver 744 * HPT302 6 (HPT302) 1 UDMA133 745 * HPT302N 6 (HPT302) 2 Other driver 746 * HPT371 7 (HPT371) * UDMA133 747 * HPT374 8 (HPT374) * UDMA133 4 channel 748 * HPT372N 9 (HPT372N) * Other driver 749 * 750 * (1) UDMA133 support depends on the bus clock 751 */ 752 753 static int hpt37x_init_one(struct pci_dev *dev, const struct pci_device_id *id) 754 { 755 /* HPT370 - UDMA100 */ 756 static const struct ata_port_info info_hpt370 = { 757 .flags = ATA_FLAG_SLAVE_POSS, 758 .pio_mask = ATA_PIO4, 759 .mwdma_mask = ATA_MWDMA2, 760 .udma_mask = ATA_UDMA5, 761 .port_ops = &hpt370_port_ops 762 }; 763 /* HPT370A - UDMA100 */ 764 static const struct ata_port_info info_hpt370a = { 765 .flags = ATA_FLAG_SLAVE_POSS, 766 .pio_mask = ATA_PIO4, 767 .mwdma_mask = ATA_MWDMA2, 768 .udma_mask = ATA_UDMA5, 769 .port_ops = &hpt370a_port_ops 770 }; 771 /* HPT370 - UDMA66 */ 772 static const struct ata_port_info info_hpt370_33 = { 773 .flags = ATA_FLAG_SLAVE_POSS, 774 .pio_mask = ATA_PIO4, 775 .mwdma_mask = ATA_MWDMA2, 776 .udma_mask = ATA_UDMA4, 777 .port_ops = &hpt370_port_ops 778 }; 779 /* HPT370A - UDMA66 */ 780 static const struct ata_port_info info_hpt370a_33 = { 781 .flags = ATA_FLAG_SLAVE_POSS, 782 .pio_mask = ATA_PIO4, 783 .mwdma_mask = ATA_MWDMA2, 784 .udma_mask = ATA_UDMA4, 785 .port_ops = &hpt370a_port_ops 786 }; 787 /* HPT372 - UDMA133 */ 788 static const struct ata_port_info info_hpt372 = { 789 .flags = ATA_FLAG_SLAVE_POSS, 790 .pio_mask = ATA_PIO4, 791 .mwdma_mask = ATA_MWDMA2, 792 .udma_mask = ATA_UDMA6, 793 .port_ops = &hpt372_port_ops 794 }; 795 /* HPT371, 302 - UDMA133 */ 796 static const struct ata_port_info info_hpt302 = { 797 .flags = ATA_FLAG_SLAVE_POSS, 798 .pio_mask = ATA_PIO4, 799 .mwdma_mask = ATA_MWDMA2, 800 .udma_mask = ATA_UDMA6, 801 .port_ops = &hpt302_port_ops 802 }; 803 /* HPT374 - UDMA100, function 1 uses different cable_detect method */ 804 static const struct ata_port_info info_hpt374_fn0 = { 805 .flags = ATA_FLAG_SLAVE_POSS, 806 .pio_mask = ATA_PIO4, 807 .mwdma_mask = ATA_MWDMA2, 808 .udma_mask = ATA_UDMA5, 809 .port_ops = &hpt372_port_ops 810 }; 811 static const struct ata_port_info info_hpt374_fn1 = { 812 .flags = ATA_FLAG_SLAVE_POSS, 813 .pio_mask = ATA_PIO4, 814 .mwdma_mask = ATA_MWDMA2, 815 .udma_mask = ATA_UDMA5, 816 .port_ops = &hpt374_fn1_port_ops 817 }; 818 819 static const int MHz[4] = { 33, 40, 50, 66 }; 820 void *private_data = NULL; 821 const struct ata_port_info *ppi[] = { NULL, NULL }; 822 u8 rev = dev->revision; 823 u8 irqmask; 824 u8 mcr1; 825 u32 freq; 826 int prefer_dpll = 1; 827 828 unsigned long iobase = pci_resource_start(dev, 4); 829 830 const struct hpt_chip *chip_table; 831 int clock_slot; 832 int rc; 833 834 rc = pcim_enable_device(dev); 835 if (rc) 836 return rc; 837 838 switch (dev->device) { 839 case PCI_DEVICE_ID_TTI_HPT366: 840 /* May be a later chip in disguise. Check */ 841 /* Older chips are in the HPT366 driver. Ignore them */ 842 if (rev < 3) 843 return -ENODEV; 844 /* N series chips have their own driver. Ignore */ 845 if (rev == 6) 846 return -ENODEV; 847 848 switch (rev) { 849 case 3: 850 ppi[0] = &info_hpt370; 851 chip_table = &hpt370; 852 prefer_dpll = 0; 853 break; 854 case 4: 855 ppi[0] = &info_hpt370a; 856 chip_table = &hpt370a; 857 prefer_dpll = 0; 858 break; 859 case 5: 860 ppi[0] = &info_hpt372; 861 chip_table = &hpt372; 862 break; 863 default: 864 pr_err("Unknown HPT366 subtype, please report (%d)\n", 865 rev); 866 return -ENODEV; 867 } 868 break; 869 case PCI_DEVICE_ID_TTI_HPT372: 870 /* 372N if rev >= 2 */ 871 if (rev >= 2) 872 return -ENODEV; 873 ppi[0] = &info_hpt372; 874 chip_table = &hpt372a; 875 break; 876 case PCI_DEVICE_ID_TTI_HPT302: 877 /* 302N if rev > 1 */ 878 if (rev > 1) 879 return -ENODEV; 880 ppi[0] = &info_hpt302; 881 /* Check this */ 882 chip_table = &hpt302; 883 break; 884 case PCI_DEVICE_ID_TTI_HPT371: 885 if (rev > 1) 886 return -ENODEV; 887 ppi[0] = &info_hpt302; 888 chip_table = &hpt371; 889 /* 890 * Single channel device, master is not present but the BIOS 891 * (or us for non x86) must mark it absent 892 */ 893 pci_read_config_byte(dev, 0x50, &mcr1); 894 mcr1 &= ~0x04; 895 pci_write_config_byte(dev, 0x50, mcr1); 896 break; 897 case PCI_DEVICE_ID_TTI_HPT374: 898 chip_table = &hpt374; 899 if (!(PCI_FUNC(dev->devfn) & 1)) 900 *ppi = &info_hpt374_fn0; 901 else 902 *ppi = &info_hpt374_fn1; 903 break; 904 default: 905 pr_err("PCI table is bogus, please report (%d)\n", dev->device); 906 return -ENODEV; 907 } 908 /* Ok so this is a chip we support */ 909 910 pci_write_config_byte(dev, PCI_CACHE_LINE_SIZE, (L1_CACHE_BYTES / 4)); 911 pci_write_config_byte(dev, PCI_LATENCY_TIMER, 0x78); 912 pci_write_config_byte(dev, PCI_MIN_GNT, 0x08); 913 pci_write_config_byte(dev, PCI_MAX_LAT, 0x08); 914 915 pci_read_config_byte(dev, 0x5A, &irqmask); 916 irqmask &= ~0x10; 917 pci_write_config_byte(dev, 0x5a, irqmask); 918 919 /* 920 * default to pci clock. make sure MA15/16 are set to output 921 * to prevent drives having problems with 40-pin cables. Needed 922 * for some drives such as IBM-DTLA which will not enter ready 923 * state on reset when PDIAG is a input. 924 */ 925 926 pci_write_config_byte(dev, 0x5b, 0x23); 927 928 /* 929 * HighPoint does this for HPT372A. 930 * NOTE: This register is only writeable via I/O space. 931 */ 932 if (chip_table == &hpt372a) 933 outb(0x0e, iobase + 0x9c); 934 935 /* 936 * Some devices do not let this value be accessed via PCI space 937 * according to the old driver. In addition we must use the value 938 * from FN 0 on the HPT374. 939 */ 940 941 if (chip_table == &hpt374) { 942 freq = hpt374_read_freq(dev); 943 if (freq == 0) 944 return -ENODEV; 945 } else 946 freq = inl(iobase + 0x90); 947 948 if ((freq >> 12) != 0xABCDE) { 949 int i; 950 u8 sr; 951 u32 total = 0; 952 953 pr_warn("BIOS has not set timing clocks\n"); 954 955 /* This is the process the HPT371 BIOS is reported to use */ 956 for (i = 0; i < 128; i++) { 957 pci_read_config_byte(dev, 0x78, &sr); 958 total += sr & 0x1FF; 959 udelay(15); 960 } 961 freq = total / 128; 962 } 963 freq &= 0x1FF; 964 965 /* 966 * Turn the frequency check into a band and then find a timing 967 * table to match it. 968 */ 969 970 clock_slot = hpt37x_clock_slot(freq, chip_table->base); 971 if (chip_table->clocks[clock_slot] == NULL || prefer_dpll) { 972 /* 973 * We need to try PLL mode instead 974 * 975 * For non UDMA133 capable devices we should 976 * use a 50MHz DPLL by choice 977 */ 978 unsigned int f_low, f_high; 979 int dpll, adjust; 980 981 /* Compute DPLL */ 982 dpll = (ppi[0]->udma_mask & 0xC0) ? 3 : 2; 983 984 f_low = (MHz[clock_slot] * 48) / MHz[dpll]; 985 f_high = f_low + 2; 986 if (clock_slot > 1) 987 f_high += 2; 988 989 /* Select the DPLL clock. */ 990 pci_write_config_byte(dev, 0x5b, 0x21); 991 pci_write_config_dword(dev, 0x5C, 992 (f_high << 16) | f_low | 0x100); 993 994 for (adjust = 0; adjust < 8; adjust++) { 995 if (hpt37x_calibrate_dpll(dev)) 996 break; 997 /* 998 * See if it'll settle at a fractionally 999 * different clock 1000 */ 1001 if (adjust & 1) 1002 f_low -= adjust >> 1; 1003 else 1004 f_high += adjust >> 1; 1005 pci_write_config_dword(dev, 0x5C, 1006 (f_high << 16) | f_low | 0x100); 1007 } 1008 if (adjust == 8) { 1009 pr_err("DPLL did not stabilize!\n"); 1010 return -ENODEV; 1011 } 1012 if (dpll == 3) 1013 private_data = (void *)hpt37x_timings_66; 1014 else 1015 private_data = (void *)hpt37x_timings_50; 1016 1017 pr_info("bus clock %dMHz, using %dMHz DPLL\n", 1018 MHz[clock_slot], MHz[dpll]); 1019 } else { 1020 private_data = (void *)chip_table->clocks[clock_slot]; 1021 /* 1022 * Perform a final fixup. Note that we will have used the 1023 * DPLL on the HPT372 which means we don't have to worry 1024 * about lack of UDMA133 support on lower clocks 1025 */ 1026 1027 if (clock_slot < 2 && ppi[0] == &info_hpt370) 1028 ppi[0] = &info_hpt370_33; 1029 if (clock_slot < 2 && ppi[0] == &info_hpt370a) 1030 ppi[0] = &info_hpt370a_33; 1031 1032 pr_info("%s using %dMHz bus clock\n", 1033 chip_table->name, MHz[clock_slot]); 1034 } 1035 1036 /* Now kick off ATA set up */ 1037 return ata_pci_bmdma_init_one(dev, ppi, &hpt37x_sht, private_data, 0); 1038 } 1039 1040 static const struct pci_device_id hpt37x[] = { 1041 { PCI_VDEVICE(TTI, PCI_DEVICE_ID_TTI_HPT366), }, 1042 { PCI_VDEVICE(TTI, PCI_DEVICE_ID_TTI_HPT371), }, 1043 { PCI_VDEVICE(TTI, PCI_DEVICE_ID_TTI_HPT372), }, 1044 { PCI_VDEVICE(TTI, PCI_DEVICE_ID_TTI_HPT374), }, 1045 { PCI_VDEVICE(TTI, PCI_DEVICE_ID_TTI_HPT302), }, 1046 1047 { }, 1048 }; 1049 1050 static struct pci_driver hpt37x_pci_driver = { 1051 .name = DRV_NAME, 1052 .id_table = hpt37x, 1053 .probe = hpt37x_init_one, 1054 .remove = ata_pci_remove_one 1055 }; 1056 1057 module_pci_driver(hpt37x_pci_driver); 1058 1059 MODULE_AUTHOR("Alan Cox"); 1060 MODULE_DESCRIPTION("low-level driver for the Highpoint HPT37x/30x"); 1061 MODULE_LICENSE("GPL"); 1062 MODULE_DEVICE_TABLE(pci, hpt37x); 1063 MODULE_VERSION(DRV_VERSION); 1064