1 // SPDX-License-Identifier: GPL-2.0-only 2 /* 3 * Libata driver for the highpoint 366 and 368 UDMA66 ATA controllers. 4 * 5 * This driver is heavily based upon: 6 * 7 * linux/drivers/ide/pci/hpt366.c Version 0.36 April 25, 2003 8 * 9 * Copyright (C) 1999-2003 Andre Hedrick <andre@linux-ide.org> 10 * Portions Copyright (C) 2001 Sun Microsystems, Inc. 11 * Portions Copyright (C) 2003 Red Hat Inc 12 * 13 * 14 * TODO 15 * Look into engine reset on timeout errors. Should not be required. 16 */ 17 #include <linux/kernel.h> 18 #include <linux/module.h> 19 #include <linux/pci.h> 20 #include <linux/blkdev.h> 21 #include <linux/delay.h> 22 #include <scsi/scsi_host.h> 23 #include <linux/libata.h> 24 25 #define DRV_NAME "pata_hpt366" 26 #define DRV_VERSION "0.6.13" 27 28 struct hpt_clock { 29 u8 xfer_mode; 30 u32 timing; 31 }; 32 33 /* key for bus clock timings 34 * bit 35 * 0:3 data_high_time. Inactive time of DIOW_/DIOR_ for PIO and MW DMA. 36 * cycles = value + 1 37 * 4:7 data_low_time. Active time of DIOW_/DIOR_ for PIO and MW DMA. 38 * cycles = value + 1 39 * 8:11 cmd_high_time. Inactive time of DIOW_/DIOR_ during task file 40 * register access. 41 * 12:15 cmd_low_time. Active time of DIOW_/DIOR_ during task file 42 * register access. 43 * 16:18 udma_cycle_time. Clock cycles for UDMA xfer? 44 * 19:21 pre_high_time. Time to initialize 1st cycle for PIO and MW DMA xfer. 45 * 22:24 cmd_pre_high_time. Time to initialize 1st PIO cycle for task file 46 * register access. 47 * 28 UDMA enable. 48 * 29 DMA enable. 49 * 30 PIO_MST enable. If set, the chip is in bus master mode during 50 * PIO xfer. 51 * 31 FIFO enable. 52 */ 53 54 static const struct hpt_clock hpt366_40[] = { 55 { XFER_UDMA_4, 0x900fd943 }, 56 { XFER_UDMA_3, 0x900ad943 }, 57 { XFER_UDMA_2, 0x900bd943 }, 58 { XFER_UDMA_1, 0x9008d943 }, 59 { XFER_UDMA_0, 0x9008d943 }, 60 61 { XFER_MW_DMA_2, 0xa008d943 }, 62 { XFER_MW_DMA_1, 0xa010d955 }, 63 { XFER_MW_DMA_0, 0xa010d9fc }, 64 65 { XFER_PIO_4, 0xc008d963 }, 66 { XFER_PIO_3, 0xc010d974 }, 67 { XFER_PIO_2, 0xc010d997 }, 68 { XFER_PIO_1, 0xc010d9c7 }, 69 { XFER_PIO_0, 0xc018d9d9 }, 70 { 0, 0x0120d9d9 } 71 }; 72 73 static const struct hpt_clock hpt366_33[] = { 74 { XFER_UDMA_4, 0x90c9a731 }, 75 { XFER_UDMA_3, 0x90cfa731 }, 76 { XFER_UDMA_2, 0x90caa731 }, 77 { XFER_UDMA_1, 0x90cba731 }, 78 { XFER_UDMA_0, 0x90c8a731 }, 79 80 { XFER_MW_DMA_2, 0xa0c8a731 }, 81 { XFER_MW_DMA_1, 0xa0c8a732 }, /* 0xa0c8a733 */ 82 { XFER_MW_DMA_0, 0xa0c8a797 }, 83 84 { XFER_PIO_4, 0xc0c8a731 }, 85 { XFER_PIO_3, 0xc0c8a742 }, 86 { XFER_PIO_2, 0xc0d0a753 }, 87 { XFER_PIO_1, 0xc0d0a7a3 }, /* 0xc0d0a793 */ 88 { XFER_PIO_0, 0xc0d0a7aa }, /* 0xc0d0a7a7 */ 89 { 0, 0x0120a7a7 } 90 }; 91 92 static const struct hpt_clock hpt366_25[] = { 93 { XFER_UDMA_4, 0x90c98521 }, 94 { XFER_UDMA_3, 0x90cf8521 }, 95 { XFER_UDMA_2, 0x90cf8521 }, 96 { XFER_UDMA_1, 0x90cb8521 }, 97 { XFER_UDMA_0, 0x90cb8521 }, 98 99 { XFER_MW_DMA_2, 0xa0ca8521 }, 100 { XFER_MW_DMA_1, 0xa0ca8532 }, 101 { XFER_MW_DMA_0, 0xa0ca8575 }, 102 103 { XFER_PIO_4, 0xc0ca8521 }, 104 { XFER_PIO_3, 0xc0ca8532 }, 105 { XFER_PIO_2, 0xc0ca8542 }, 106 { XFER_PIO_1, 0xc0d08572 }, 107 { XFER_PIO_0, 0xc0d08585 }, 108 { 0, 0x01208585 } 109 }; 110 111 /** 112 * hpt36x_find_mode - find the hpt36x timing 113 * @ap: ATA port 114 * @speed: transfer mode 115 * 116 * Return the 32bit register programming information for this channel 117 * that matches the speed provided. 118 */ 119 120 static u32 hpt36x_find_mode(struct ata_port *ap, int speed) 121 { 122 struct hpt_clock *clocks = ap->host->private_data; 123 124 while (clocks->xfer_mode) { 125 if (clocks->xfer_mode == speed) 126 return clocks->timing; 127 clocks++; 128 } 129 BUG(); 130 return 0xffffffffU; /* silence compiler warning */ 131 } 132 133 static const char * const bad_ata33[] = { 134 "Maxtor 92720U8", "Maxtor 92040U6", "Maxtor 91360U4", "Maxtor 91020U3", 135 "Maxtor 90845U3", "Maxtor 90650U2", 136 "Maxtor 91360D8", "Maxtor 91190D7", "Maxtor 91020D6", "Maxtor 90845D5", 137 "Maxtor 90680D4", "Maxtor 90510D3", "Maxtor 90340D2", 138 "Maxtor 91152D8", "Maxtor 91008D7", "Maxtor 90845D6", "Maxtor 90840D6", 139 "Maxtor 90720D5", "Maxtor 90648D5", "Maxtor 90576D4", 140 "Maxtor 90510D4", 141 "Maxtor 90432D3", "Maxtor 90288D2", "Maxtor 90256D2", 142 "Maxtor 91000D8", "Maxtor 90910D8", "Maxtor 90875D7", "Maxtor 90840D7", 143 "Maxtor 90750D6", "Maxtor 90625D5", "Maxtor 90500D4", 144 "Maxtor 91728D8", "Maxtor 91512D7", "Maxtor 91303D6", "Maxtor 91080D5", 145 "Maxtor 90845D4", "Maxtor 90680D4", "Maxtor 90648D3", "Maxtor 90432D2", 146 NULL 147 }; 148 149 static const char * const bad_ata66_4[] = { 150 "IBM-DTLA-307075", 151 "IBM-DTLA-307060", 152 "IBM-DTLA-307045", 153 "IBM-DTLA-307030", 154 "IBM-DTLA-307020", 155 "IBM-DTLA-307015", 156 "IBM-DTLA-305040", 157 "IBM-DTLA-305030", 158 "IBM-DTLA-305020", 159 "IC35L010AVER07-0", 160 "IC35L020AVER07-0", 161 "IC35L030AVER07-0", 162 "IC35L040AVER07-0", 163 "IC35L060AVER07-0", 164 "WDC AC310200R", 165 NULL 166 }; 167 168 static const char * const bad_ata66_3[] = { 169 "WDC AC310200R", 170 NULL 171 }; 172 173 static int hpt_dma_blacklisted(const struct ata_device *dev, char *modestr, 174 const char * const list[]) 175 { 176 unsigned char model_num[ATA_ID_PROD_LEN + 1]; 177 int i; 178 179 ata_id_c_string(dev->id, model_num, ATA_ID_PROD, sizeof(model_num)); 180 181 i = match_string(list, -1, model_num); 182 if (i >= 0) { 183 ata_dev_warn(dev, "%s is not supported for %s\n", modestr, list[i]); 184 return 1; 185 } 186 return 0; 187 } 188 189 /** 190 * hpt366_filter - mode selection filter 191 * @adev: ATA device 192 * @mask: Current mask to manipulate and pass back 193 * 194 * Block UDMA on devices that cause trouble with this controller. 195 */ 196 197 static unsigned long hpt366_filter(struct ata_device *adev, unsigned long mask) 198 { 199 if (adev->class == ATA_DEV_ATA) { 200 if (hpt_dma_blacklisted(adev, "UDMA", bad_ata33)) 201 mask &= ~ATA_MASK_UDMA; 202 if (hpt_dma_blacklisted(adev, "UDMA3", bad_ata66_3)) 203 mask &= ~(0xF8 << ATA_SHIFT_UDMA); 204 if (hpt_dma_blacklisted(adev, "UDMA4", bad_ata66_4)) 205 mask &= ~(0xF0 << ATA_SHIFT_UDMA); 206 } else if (adev->class == ATA_DEV_ATAPI) 207 mask &= ~(ATA_MASK_MWDMA | ATA_MASK_UDMA); 208 209 return mask; 210 } 211 212 static int hpt36x_cable_detect(struct ata_port *ap) 213 { 214 struct pci_dev *pdev = to_pci_dev(ap->host->dev); 215 u8 ata66; 216 217 /* 218 * Each channel of pata_hpt366 occupies separate PCI function 219 * as the primary channel and bit1 indicates the cable type. 220 */ 221 pci_read_config_byte(pdev, 0x5A, &ata66); 222 if (ata66 & 2) 223 return ATA_CBL_PATA40; 224 return ATA_CBL_PATA80; 225 } 226 227 static void hpt366_set_mode(struct ata_port *ap, struct ata_device *adev, 228 u8 mode) 229 { 230 struct pci_dev *pdev = to_pci_dev(ap->host->dev); 231 u32 addr = 0x40 + 4 * adev->devno; 232 u32 mask, reg, t; 233 234 /* determine timing mask and find matching clock entry */ 235 if (mode < XFER_MW_DMA_0) 236 mask = 0xc1f8ffff; 237 else if (mode < XFER_UDMA_0) 238 mask = 0x303800ff; 239 else 240 mask = 0x30070000; 241 242 t = hpt36x_find_mode(ap, mode); 243 244 /* 245 * Combine new mode bits with old config bits and disable 246 * on-chip PIO FIFO/buffer (and PIO MST mode as well) to avoid 247 * problems handling I/O errors later. 248 */ 249 pci_read_config_dword(pdev, addr, ®); 250 reg = ((reg & ~mask) | (t & mask)) & ~0xc0000000; 251 pci_write_config_dword(pdev, addr, reg); 252 } 253 254 /** 255 * hpt366_set_piomode - PIO setup 256 * @ap: ATA interface 257 * @adev: device on the interface 258 * 259 * Perform PIO mode setup. 260 */ 261 262 static void hpt366_set_piomode(struct ata_port *ap, struct ata_device *adev) 263 { 264 hpt366_set_mode(ap, adev, adev->pio_mode); 265 } 266 267 /** 268 * hpt366_set_dmamode - DMA timing setup 269 * @ap: ATA interface 270 * @adev: Device being configured 271 * 272 * Set up the channel for MWDMA or UDMA modes. Much the same as with 273 * PIO, load the mode number and then set MWDMA or UDMA flag. 274 */ 275 276 static void hpt366_set_dmamode(struct ata_port *ap, struct ata_device *adev) 277 { 278 hpt366_set_mode(ap, adev, adev->dma_mode); 279 } 280 281 /** 282 * hpt366_prereset - reset the hpt36x bus 283 * @link: ATA link to reset 284 * @deadline: deadline jiffies for the operation 285 * 286 * Perform the initial reset handling for the 36x series controllers. 287 * Reset the hardware and state machine, 288 */ 289 290 static int hpt366_prereset(struct ata_link *link, unsigned long deadline) 291 { 292 struct ata_port *ap = link->ap; 293 struct pci_dev *pdev = to_pci_dev(ap->host->dev); 294 /* 295 * HPT36x chips have one channel per function and have 296 * both channel enable bits located differently and visible 297 * to both functions -- really stupid design decision... :-( 298 * Bit 4 is for the primary channel, bit 5 for the secondary. 299 */ 300 static const struct pci_bits hpt366_enable_bits = { 301 0x50, 1, 0x30, 0x30 302 }; 303 u8 mcr2; 304 305 if (!pci_test_config_bits(pdev, &hpt366_enable_bits)) 306 return -ENOENT; 307 308 pci_read_config_byte(pdev, 0x51, &mcr2); 309 if (mcr2 & 0x80) 310 pci_write_config_byte(pdev, 0x51, mcr2 & ~0x80); 311 312 return ata_sff_prereset(link, deadline); 313 } 314 315 static struct scsi_host_template hpt36x_sht = { 316 ATA_BMDMA_SHT(DRV_NAME), 317 }; 318 319 /* 320 * Configuration for HPT366/68 321 */ 322 323 static struct ata_port_operations hpt366_port_ops = { 324 .inherits = &ata_bmdma_port_ops, 325 .prereset = hpt366_prereset, 326 .cable_detect = hpt36x_cable_detect, 327 .mode_filter = hpt366_filter, 328 .set_piomode = hpt366_set_piomode, 329 .set_dmamode = hpt366_set_dmamode, 330 }; 331 332 /** 333 * hpt36x_init_chipset - common chip setup 334 * @dev: PCI device 335 * 336 * Perform the chip setup work that must be done at both init and 337 * resume time 338 */ 339 340 static void hpt36x_init_chipset(struct pci_dev *dev) 341 { 342 u8 mcr1; 343 344 pci_write_config_byte(dev, PCI_CACHE_LINE_SIZE, (L1_CACHE_BYTES / 4)); 345 pci_write_config_byte(dev, PCI_LATENCY_TIMER, 0x78); 346 pci_write_config_byte(dev, PCI_MIN_GNT, 0x08); 347 pci_write_config_byte(dev, PCI_MAX_LAT, 0x08); 348 349 /* 350 * Now we'll have to force both channels enabled if at least one 351 * of them has been enabled by BIOS... 352 */ 353 pci_read_config_byte(dev, 0x50, &mcr1); 354 if (mcr1 & 0x30) 355 pci_write_config_byte(dev, 0x50, mcr1 | 0x30); 356 } 357 358 /** 359 * hpt36x_init_one - Initialise an HPT366/368 360 * @dev: PCI device 361 * @id: Entry in match table 362 * 363 * Initialise an HPT36x device. There are some interesting complications 364 * here. Firstly the chip may report 366 and be one of several variants. 365 * Secondly all the timings depend on the clock for the chip which we must 366 * detect and look up 367 * 368 * This is the known chip mappings. It may be missing a couple of later 369 * releases. 370 * 371 * Chip version PCI Rev Notes 372 * HPT366 4 (HPT366) 0 UDMA66 373 * HPT366 4 (HPT366) 1 UDMA66 374 * HPT368 4 (HPT366) 2 UDMA66 375 * HPT37x/30x 4 (HPT366) 3+ Other driver 376 * 377 */ 378 379 static int hpt36x_init_one(struct pci_dev *dev, const struct pci_device_id *id) 380 { 381 static const struct ata_port_info info_hpt366 = { 382 .flags = ATA_FLAG_SLAVE_POSS, 383 .pio_mask = ATA_PIO4, 384 .mwdma_mask = ATA_MWDMA2, 385 .udma_mask = ATA_UDMA4, 386 .port_ops = &hpt366_port_ops 387 }; 388 const struct ata_port_info *ppi[] = { &info_hpt366, NULL }; 389 390 const void *hpriv = NULL; 391 u32 reg1; 392 int rc; 393 394 rc = pcim_enable_device(dev); 395 if (rc) 396 return rc; 397 398 /* May be a later chip in disguise. Check */ 399 /* Newer chips are not in the HPT36x driver. Ignore them */ 400 if (dev->revision > 2) 401 return -ENODEV; 402 403 hpt36x_init_chipset(dev); 404 405 pci_read_config_dword(dev, 0x40, ®1); 406 407 /* PCI clocking determines the ATA timing values to use */ 408 /* info_hpt366 is safe against re-entry so we can scribble on it */ 409 switch ((reg1 & 0xf00) >> 8) { 410 case 9: 411 hpriv = &hpt366_40; 412 break; 413 case 5: 414 hpriv = &hpt366_25; 415 break; 416 default: 417 hpriv = &hpt366_33; 418 break; 419 } 420 /* Now kick off ATA set up */ 421 return ata_pci_bmdma_init_one(dev, ppi, &hpt36x_sht, (void *)hpriv, 0); 422 } 423 424 #ifdef CONFIG_PM_SLEEP 425 static int hpt36x_reinit_one(struct pci_dev *dev) 426 { 427 struct ata_host *host = pci_get_drvdata(dev); 428 int rc; 429 430 rc = ata_pci_device_do_resume(dev); 431 if (rc) 432 return rc; 433 hpt36x_init_chipset(dev); 434 ata_host_resume(host); 435 return 0; 436 } 437 #endif 438 439 static const struct pci_device_id hpt36x[] = { 440 { PCI_VDEVICE(TTI, PCI_DEVICE_ID_TTI_HPT366), }, 441 { }, 442 }; 443 444 static struct pci_driver hpt36x_pci_driver = { 445 .name = DRV_NAME, 446 .id_table = hpt36x, 447 .probe = hpt36x_init_one, 448 .remove = ata_pci_remove_one, 449 #ifdef CONFIG_PM_SLEEP 450 .suspend = ata_pci_device_suspend, 451 .resume = hpt36x_reinit_one, 452 #endif 453 }; 454 455 module_pci_driver(hpt36x_pci_driver); 456 457 MODULE_AUTHOR("Alan Cox"); 458 MODULE_DESCRIPTION("low-level driver for the Highpoint HPT366/368"); 459 MODULE_LICENSE("GPL"); 460 MODULE_DEVICE_TABLE(pci, hpt36x); 461 MODULE_VERSION(DRV_VERSION); 462