1 /* 2 * pata_cypress.c - Cypress PATA for new ATA layer 3 * (C) 2006 Red Hat Inc 4 * Alan Cox 5 * 6 * Based heavily on 7 * linux/drivers/ide/pci/cy82c693.c Version 0.40 Sep. 10, 2002 8 * 9 */ 10 11 #include <linux/kernel.h> 12 #include <linux/module.h> 13 #include <linux/pci.h> 14 #include <linux/init.h> 15 #include <linux/blkdev.h> 16 #include <linux/delay.h> 17 #include <scsi/scsi_host.h> 18 #include <linux/libata.h> 19 20 #define DRV_NAME "pata_cypress" 21 #define DRV_VERSION "0.1.5" 22 23 /* here are the offset definitions for the registers */ 24 25 enum { 26 CY82_IDE_CMDREG = 0x04, 27 CY82_IDE_ADDRSETUP = 0x48, 28 CY82_IDE_MASTER_IOR = 0x4C, 29 CY82_IDE_MASTER_IOW = 0x4D, 30 CY82_IDE_SLAVE_IOR = 0x4E, 31 CY82_IDE_SLAVE_IOW = 0x4F, 32 CY82_IDE_MASTER_8BIT = 0x50, 33 CY82_IDE_SLAVE_8BIT = 0x51, 34 35 CY82_INDEX_PORT = 0x22, 36 CY82_DATA_PORT = 0x23, 37 38 CY82_INDEX_CTRLREG1 = 0x01, 39 CY82_INDEX_CHANNEL0 = 0x30, 40 CY82_INDEX_CHANNEL1 = 0x31, 41 CY82_INDEX_TIMEOUT = 0x32 42 }; 43 44 /** 45 * cy82c693_set_piomode - set initial PIO mode data 46 * @ap: ATA interface 47 * @adev: ATA device 48 * 49 * Called to do the PIO mode setup. 50 */ 51 52 static void cy82c693_set_piomode(struct ata_port *ap, struct ata_device *adev) 53 { 54 struct pci_dev *pdev = to_pci_dev(ap->host->dev); 55 struct ata_timing t; 56 const unsigned long T = 1000000 / 33; 57 short time_16, time_8; 58 u32 addr; 59 60 if (ata_timing_compute(adev, adev->pio_mode, &t, T, 1) < 0) { 61 printk(KERN_ERR DRV_NAME ": mome computation failed.\n"); 62 return; 63 } 64 65 time_16 = clamp_val(t.recover, 0, 15) | (clamp_val(t.active, 0, 15) << 4); 66 time_8 = clamp_val(t.act8b, 0, 15) | (clamp_val(t.rec8b, 0, 15) << 4); 67 68 if (adev->devno == 0) { 69 pci_read_config_dword(pdev, CY82_IDE_ADDRSETUP, &addr); 70 71 addr &= ~0x0F; /* Mask bits */ 72 addr |= clamp_val(t.setup, 0, 15); 73 74 pci_write_config_dword(pdev, CY82_IDE_ADDRSETUP, addr); 75 pci_write_config_byte(pdev, CY82_IDE_MASTER_IOR, time_16); 76 pci_write_config_byte(pdev, CY82_IDE_MASTER_IOW, time_16); 77 pci_write_config_byte(pdev, CY82_IDE_MASTER_8BIT, time_8); 78 } else { 79 pci_read_config_dword(pdev, CY82_IDE_ADDRSETUP, &addr); 80 81 addr &= ~0xF0; /* Mask bits */ 82 addr |= (clamp_val(t.setup, 0, 15) << 4); 83 84 pci_write_config_dword(pdev, CY82_IDE_ADDRSETUP, addr); 85 pci_write_config_byte(pdev, CY82_IDE_SLAVE_IOR, time_16); 86 pci_write_config_byte(pdev, CY82_IDE_SLAVE_IOW, time_16); 87 pci_write_config_byte(pdev, CY82_IDE_SLAVE_8BIT, time_8); 88 } 89 } 90 91 /** 92 * cy82c693_set_dmamode - set initial DMA mode data 93 * @ap: ATA interface 94 * @adev: ATA device 95 * 96 * Called to do the DMA mode setup. 97 */ 98 99 static void cy82c693_set_dmamode(struct ata_port *ap, struct ata_device *adev) 100 { 101 int reg = CY82_INDEX_CHANNEL0 + ap->port_no; 102 103 /* Be afraid, be very afraid. Magic registers in low I/O space */ 104 outb(reg, 0x22); 105 outb(adev->dma_mode - XFER_MW_DMA_0, 0x23); 106 107 /* 0x50 gives the best behaviour on the Alpha's using this chip */ 108 outb(CY82_INDEX_TIMEOUT, 0x22); 109 outb(0x50, 0x23); 110 } 111 112 static struct scsi_host_template cy82c693_sht = { 113 ATA_BMDMA_SHT(DRV_NAME), 114 }; 115 116 static struct ata_port_operations cy82c693_port_ops = { 117 .inherits = &ata_bmdma_port_ops, 118 .cable_detect = ata_cable_40wire, 119 .set_piomode = cy82c693_set_piomode, 120 .set_dmamode = cy82c693_set_dmamode, 121 }; 122 123 static int cy82c693_init_one(struct pci_dev *pdev, const struct pci_device_id *id) 124 { 125 static const struct ata_port_info info = { 126 .flags = ATA_FLAG_SLAVE_POSS, 127 .pio_mask = ATA_PIO4, 128 .mwdma_mask = ATA_MWDMA2, 129 .port_ops = &cy82c693_port_ops 130 }; 131 const struct ata_port_info *ppi[] = { &info, &ata_dummy_port_info }; 132 133 /* Devfn 1 is the ATA primary. The secondary is magic and on devfn2. 134 For the moment we don't handle the secondary. FIXME */ 135 136 if (PCI_FUNC(pdev->devfn) != 1) 137 return -ENODEV; 138 139 return ata_pci_sff_init_one(pdev, ppi, &cy82c693_sht, NULL); 140 } 141 142 static const struct pci_device_id cy82c693[] = { 143 { PCI_VDEVICE(CONTAQ, PCI_DEVICE_ID_CONTAQ_82C693), }, 144 145 { }, 146 }; 147 148 static struct pci_driver cy82c693_pci_driver = { 149 .name = DRV_NAME, 150 .id_table = cy82c693, 151 .probe = cy82c693_init_one, 152 .remove = ata_pci_remove_one, 153 #ifdef CONFIG_PM 154 .suspend = ata_pci_device_suspend, 155 .resume = ata_pci_device_resume, 156 #endif 157 }; 158 159 static int __init cy82c693_init(void) 160 { 161 return pci_register_driver(&cy82c693_pci_driver); 162 } 163 164 165 static void __exit cy82c693_exit(void) 166 { 167 pci_unregister_driver(&cy82c693_pci_driver); 168 } 169 170 171 MODULE_AUTHOR("Alan Cox"); 172 MODULE_DESCRIPTION("low-level driver for the CY82C693 PATA controller"); 173 MODULE_LICENSE("GPL"); 174 MODULE_DEVICE_TABLE(pci, cy82c693); 175 MODULE_VERSION(DRV_VERSION); 176 177 module_init(cy82c693_init); 178 module_exit(cy82c693_exit); 179