1 // SPDX-License-Identifier: GPL-2.0-only 2 /* 3 * pata-cs5530.c - CS5530 PATA for new ATA layer 4 * (C) 2005 Red Hat Inc 5 * 6 * based upon cs5530.c by Mark Lord. 7 * 8 * Loosely based on the piix & svwks drivers. 9 * 10 * Documentation: 11 * Available from AMD web site. 12 */ 13 14 #include <linux/kernel.h> 15 #include <linux/module.h> 16 #include <linux/pci.h> 17 #include <linux/blkdev.h> 18 #include <linux/delay.h> 19 #include <scsi/scsi_host.h> 20 #include <linux/libata.h> 21 #include <linux/dmi.h> 22 23 #define DRV_NAME "pata_cs5530" 24 #define DRV_VERSION "0.7.4" 25 26 static void __iomem *cs5530_port_base(struct ata_port *ap) 27 { 28 unsigned long bmdma = (unsigned long)ap->ioaddr.bmdma_addr; 29 30 return (void __iomem *)((bmdma & ~0x0F) + 0x20 + 0x10 * ap->port_no); 31 } 32 33 /** 34 * cs5530_set_piomode - PIO setup 35 * @ap: ATA interface 36 * @adev: device on the interface 37 * 38 * Set our PIO requirements. This is fairly simple on the CS5530 39 * chips. 40 */ 41 42 static void cs5530_set_piomode(struct ata_port *ap, struct ata_device *adev) 43 { 44 static const unsigned int cs5530_pio_timings[2][5] = { 45 {0x00009172, 0x00012171, 0x00020080, 0x00032010, 0x00040010}, 46 {0xd1329172, 0x71212171, 0x30200080, 0x20102010, 0x00100010} 47 }; 48 void __iomem *base = cs5530_port_base(ap); 49 u32 tuning; 50 int format; 51 52 /* Find out which table to use */ 53 tuning = ioread32(base + 0x04); 54 format = (tuning & 0x80000000UL) ? 1 : 0; 55 56 /* Now load the right timing register */ 57 if (adev->devno) 58 base += 0x08; 59 60 iowrite32(cs5530_pio_timings[format][adev->pio_mode - XFER_PIO_0], base); 61 } 62 63 /** 64 * cs5530_set_dmamode - DMA timing setup 65 * @ap: ATA interface 66 * @adev: Device being configured 67 * 68 * We cannot mix MWDMA and UDMA without reloading timings each switch 69 * master to slave. We track the last DMA setup in order to minimise 70 * reloads. 71 */ 72 73 static void cs5530_set_dmamode(struct ata_port *ap, struct ata_device *adev) 74 { 75 void __iomem *base = cs5530_port_base(ap); 76 u32 tuning, timing = 0; 77 u8 reg; 78 79 /* Find out which table to use */ 80 tuning = ioread32(base + 0x04); 81 82 switch(adev->dma_mode) { 83 case XFER_UDMA_0: 84 timing = 0x00921250;break; 85 case XFER_UDMA_1: 86 timing = 0x00911140;break; 87 case XFER_UDMA_2: 88 timing = 0x00911030;break; 89 case XFER_MW_DMA_0: 90 timing = 0x00077771;break; 91 case XFER_MW_DMA_1: 92 timing = 0x00012121;break; 93 case XFER_MW_DMA_2: 94 timing = 0x00002020;break; 95 default: 96 BUG(); 97 } 98 /* Merge in the PIO format bit */ 99 timing |= (tuning & 0x80000000UL); 100 if (adev->devno == 0) /* Master */ 101 iowrite32(timing, base + 0x04); 102 else { 103 if (timing & 0x00100000) 104 tuning |= 0x00100000; /* UDMA for both */ 105 else 106 tuning &= ~0x00100000; /* MWDMA for both */ 107 iowrite32(tuning, base + 0x04); 108 iowrite32(timing, base + 0x0C); 109 } 110 111 /* Set the DMA capable bit in the BMDMA area */ 112 reg = ioread8(ap->ioaddr.bmdma_addr + ATA_DMA_STATUS); 113 reg |= (1 << (5 + adev->devno)); 114 iowrite8(reg, ap->ioaddr.bmdma_addr + ATA_DMA_STATUS); 115 116 /* Remember the last DMA setup we did */ 117 118 ap->private_data = adev; 119 } 120 121 /** 122 * cs5530_qc_issue - command issue 123 * @qc: command pending 124 * 125 * Called when the libata layer is about to issue a command. We wrap 126 * this interface so that we can load the correct ATA timings if 127 * necessary. Specifically we have a problem that there is only 128 * one MWDMA/UDMA bit. 129 */ 130 131 static unsigned int cs5530_qc_issue(struct ata_queued_cmd *qc) 132 { 133 struct ata_port *ap = qc->ap; 134 struct ata_device *adev = qc->dev; 135 struct ata_device *prev = ap->private_data; 136 137 /* See if the DMA settings could be wrong */ 138 if (ata_dma_enabled(adev) && adev != prev && prev != NULL) { 139 /* Maybe, but do the channels match MWDMA/UDMA ? */ 140 if ((ata_using_udma(adev) && !ata_using_udma(prev)) || 141 (ata_using_udma(prev) && !ata_using_udma(adev))) 142 /* Switch the mode bits */ 143 cs5530_set_dmamode(ap, adev); 144 } 145 146 return ata_bmdma_qc_issue(qc); 147 } 148 149 static const struct scsi_host_template cs5530_sht = { 150 ATA_BASE_SHT(DRV_NAME), 151 .sg_tablesize = LIBATA_DUMB_MAX_PRD, 152 .dma_boundary = ATA_DMA_BOUNDARY, 153 }; 154 155 static struct ata_port_operations cs5530_port_ops = { 156 .inherits = &ata_bmdma_port_ops, 157 158 .qc_prep = ata_bmdma_dumb_qc_prep, 159 .qc_issue = cs5530_qc_issue, 160 161 .cable_detect = ata_cable_40wire, 162 .set_piomode = cs5530_set_piomode, 163 .set_dmamode = cs5530_set_dmamode, 164 }; 165 166 static const struct dmi_system_id palmax_dmi_table[] = { 167 { 168 .ident = "Palmax PD1100", 169 .matches = { 170 DMI_MATCH(DMI_SYS_VENDOR, "Cyrix"), 171 DMI_MATCH(DMI_PRODUCT_NAME, "Caddis"), 172 }, 173 }, 174 { } 175 }; 176 177 static int cs5530_is_palmax(void) 178 { 179 if (dmi_check_system(palmax_dmi_table)) { 180 printk(KERN_INFO "Palmax PD1100: Disabling DMA on docking port.\n"); 181 return 1; 182 } 183 return 0; 184 } 185 186 187 /** 188 * cs5530_init_chip - Chipset init 189 * 190 * Perform the chip initialisation work that is shared between both 191 * setup and resume paths 192 */ 193 194 static int cs5530_init_chip(void) 195 { 196 struct pci_dev *master_0 = NULL, *cs5530_0 = NULL, *dev = NULL; 197 198 while ((dev = pci_get_device(PCI_VENDOR_ID_CYRIX, PCI_ANY_ID, dev)) != NULL) { 199 switch (dev->device) { 200 case PCI_DEVICE_ID_CYRIX_PCI_MASTER: 201 master_0 = pci_dev_get(dev); 202 break; 203 case PCI_DEVICE_ID_CYRIX_5530_LEGACY: 204 cs5530_0 = pci_dev_get(dev); 205 break; 206 } 207 } 208 if (!master_0) { 209 printk(KERN_ERR DRV_NAME ": unable to locate PCI MASTER function\n"); 210 goto fail_put; 211 } 212 if (!cs5530_0) { 213 printk(KERN_ERR DRV_NAME ": unable to locate CS5530 LEGACY function\n"); 214 goto fail_put; 215 } 216 217 pci_set_master(cs5530_0); 218 pci_try_set_mwi(cs5530_0); 219 220 /* 221 * Set PCI CacheLineSize to 16-bytes: 222 * --> Write 0x04 into 8-bit PCI CACHELINESIZE reg of function 0 of the cs5530 223 * 224 * Note: This value is constant because the 5530 is only a Geode companion 225 */ 226 227 pci_write_config_byte(cs5530_0, PCI_CACHE_LINE_SIZE, 0x04); 228 229 /* 230 * Disable trapping of UDMA register accesses (Win98 hack): 231 * --> Write 0x5006 into 16-bit reg at offset 0xd0 of function 0 of the cs5530 232 */ 233 234 pci_write_config_word(cs5530_0, 0xd0, 0x5006); 235 236 /* 237 * Bit-1 at 0x40 enables MemoryWriteAndInvalidate on internal X-bus: 238 * The other settings are what is necessary to get the register 239 * into a sane state for IDE DMA operation. 240 */ 241 242 pci_write_config_byte(master_0, 0x40, 0x1e); 243 244 /* 245 * Set max PCI burst size (16-bytes seems to work best): 246 * 16bytes: set bit-1 at 0x41 (reg value of 0x16) 247 * all others: clear bit-1 at 0x41, and do: 248 * 128bytes: OR 0x00 at 0x41 249 * 256bytes: OR 0x04 at 0x41 250 * 512bytes: OR 0x08 at 0x41 251 * 1024bytes: OR 0x0c at 0x41 252 */ 253 254 pci_write_config_byte(master_0, 0x41, 0x14); 255 256 /* 257 * These settings are necessary to get the chip 258 * into a sane state for IDE DMA operation. 259 */ 260 261 pci_write_config_byte(master_0, 0x42, 0x00); 262 pci_write_config_byte(master_0, 0x43, 0xc1); 263 264 pci_dev_put(master_0); 265 pci_dev_put(cs5530_0); 266 return 0; 267 fail_put: 268 pci_dev_put(master_0); 269 pci_dev_put(cs5530_0); 270 return -ENODEV; 271 } 272 273 /** 274 * cs5530_init_one - Initialise a CS5530 275 * @pdev: PCI device 276 * @id: Entry in match table 277 * 278 * Install a driver for the newly found CS5530 companion chip. Most of 279 * this is just housekeeping. We have to set the chip up correctly and 280 * turn off various bits of emulation magic. 281 */ 282 283 static int cs5530_init_one(struct pci_dev *pdev, const struct pci_device_id *id) 284 { 285 static const struct ata_port_info info = { 286 .flags = ATA_FLAG_SLAVE_POSS, 287 .pio_mask = ATA_PIO4, 288 .mwdma_mask = ATA_MWDMA2, 289 .udma_mask = ATA_UDMA2, 290 .port_ops = &cs5530_port_ops 291 }; 292 /* The docking connector doesn't do UDMA, and it seems not MWDMA */ 293 static const struct ata_port_info info_palmax_secondary = { 294 .flags = ATA_FLAG_SLAVE_POSS, 295 .pio_mask = ATA_PIO4, 296 .port_ops = &cs5530_port_ops 297 }; 298 const struct ata_port_info *ppi[] = { &info, NULL }; 299 int rc; 300 301 rc = pcim_enable_device(pdev); 302 if (rc) 303 return rc; 304 305 /* Chip initialisation */ 306 if (cs5530_init_chip()) 307 return -ENODEV; 308 309 if (cs5530_is_palmax()) 310 ppi[1] = &info_palmax_secondary; 311 312 /* Now kick off ATA set up */ 313 return ata_pci_bmdma_init_one(pdev, ppi, &cs5530_sht, NULL, 0); 314 } 315 316 #ifdef CONFIG_PM_SLEEP 317 static int cs5530_reinit_one(struct pci_dev *pdev) 318 { 319 struct ata_host *host = pci_get_drvdata(pdev); 320 int rc; 321 322 rc = ata_pci_device_do_resume(pdev); 323 if (rc) 324 return rc; 325 326 /* If we fail on resume we are doomed */ 327 if (cs5530_init_chip()) 328 return -EIO; 329 330 ata_host_resume(host); 331 return 0; 332 } 333 #endif /* CONFIG_PM_SLEEP */ 334 335 static const struct pci_device_id cs5530[] = { 336 { PCI_VDEVICE(CYRIX, PCI_DEVICE_ID_CYRIX_5530_IDE), }, 337 338 { }, 339 }; 340 341 static struct pci_driver cs5530_pci_driver = { 342 .name = DRV_NAME, 343 .id_table = cs5530, 344 .probe = cs5530_init_one, 345 .remove = ata_pci_remove_one, 346 #ifdef CONFIG_PM_SLEEP 347 .suspend = ata_pci_device_suspend, 348 .resume = cs5530_reinit_one, 349 #endif 350 }; 351 352 module_pci_driver(cs5530_pci_driver); 353 354 MODULE_AUTHOR("Alan Cox"); 355 MODULE_DESCRIPTION("low-level driver for the Cyrix/NS/AMD 5530"); 356 MODULE_LICENSE("GPL"); 357 MODULE_DEVICE_TABLE(pci, cs5530); 358 MODULE_VERSION(DRV_VERSION); 359