1 /* 2 * IDE tuning and bus mastering support for the CS5510/CS5520 3 * chipsets 4 * 5 * The CS5510/CS5520 are slightly unusual devices. Unlike the 6 * typical IDE controllers they do bus mastering with the drive in 7 * PIO mode and smarter silicon. 8 * 9 * The practical upshot of this is that we must always tune the 10 * drive for the right PIO mode. We must also ignore all the blacklists 11 * and the drive bus mastering DMA information. Also to confuse matters 12 * further we can do DMA on PIO only drives. 13 * 14 * DMA on the 5510 also requires we disable_hlt() during DMA on early 15 * revisions. 16 * 17 * *** This driver is strictly experimental *** 18 * 19 * (c) Copyright Red Hat Inc 2002 20 * 21 * This program is free software; you can redistribute it and/or modify it 22 * under the terms of the GNU General Public License as published by the 23 * Free Software Foundation; either version 2, or (at your option) any 24 * later version. 25 * 26 * This program is distributed in the hope that it will be useful, but 27 * WITHOUT ANY WARRANTY; without even the implied warranty of 28 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU 29 * General Public License for more details. 30 * 31 * Documentation: 32 * Not publicly available. 33 */ 34 #include <linux/kernel.h> 35 #include <linux/module.h> 36 #include <linux/pci.h> 37 #include <linux/init.h> 38 #include <linux/blkdev.h> 39 #include <linux/delay.h> 40 #include <scsi/scsi_host.h> 41 #include <linux/libata.h> 42 43 #define DRV_NAME "pata_cs5520" 44 #define DRV_VERSION "0.6.6" 45 46 struct pio_clocks 47 { 48 int address; 49 int assert; 50 int recovery; 51 }; 52 53 static const struct pio_clocks cs5520_pio_clocks[]={ 54 {3, 6, 11}, 55 {2, 5, 6}, 56 {1, 4, 3}, 57 {1, 3, 2}, 58 {1, 2, 1} 59 }; 60 61 /** 62 * cs5520_set_timings - program PIO timings 63 * @ap: ATA port 64 * @adev: ATA device 65 * 66 * Program the PIO mode timings for the controller according to the pio 67 * clocking table. 68 */ 69 70 static void cs5520_set_timings(struct ata_port *ap, struct ata_device *adev, int pio) 71 { 72 struct pci_dev *pdev = to_pci_dev(ap->host->dev); 73 int slave = adev->devno; 74 75 pio -= XFER_PIO_0; 76 77 /* Channel command timing */ 78 pci_write_config_byte(pdev, 0x62 + ap->port_no, 79 (cs5520_pio_clocks[pio].recovery << 4) | 80 (cs5520_pio_clocks[pio].assert)); 81 /* FIXME: should these use address ? */ 82 /* Read command timing */ 83 pci_write_config_byte(pdev, 0x64 + 4*ap->port_no + slave, 84 (cs5520_pio_clocks[pio].recovery << 4) | 85 (cs5520_pio_clocks[pio].assert)); 86 /* Write command timing */ 87 pci_write_config_byte(pdev, 0x66 + 4*ap->port_no + slave, 88 (cs5520_pio_clocks[pio].recovery << 4) | 89 (cs5520_pio_clocks[pio].assert)); 90 } 91 92 /** 93 * cs5520_set_piomode - program PIO timings 94 * @ap: ATA port 95 * @adev: ATA device 96 * 97 * Program the PIO mode timings for the controller according to the pio 98 * clocking table. 99 */ 100 101 static void cs5520_set_piomode(struct ata_port *ap, struct ata_device *adev) 102 { 103 cs5520_set_timings(ap, adev, adev->pio_mode); 104 } 105 106 static struct scsi_host_template cs5520_sht = { 107 ATA_BMDMA_SHT(DRV_NAME), 108 .sg_tablesize = LIBATA_DUMB_MAX_PRD, 109 }; 110 111 static struct ata_port_operations cs5520_port_ops = { 112 .inherits = &ata_bmdma_port_ops, 113 .qc_prep = ata_bmdma_dumb_qc_prep, 114 .cable_detect = ata_cable_40wire, 115 .set_piomode = cs5520_set_piomode, 116 }; 117 118 static int cs5520_init_one(struct pci_dev *pdev, const struct pci_device_id *id) 119 { 120 static const unsigned int cmd_port[] = { 0x1F0, 0x170 }; 121 static const unsigned int ctl_port[] = { 0x3F6, 0x376 }; 122 struct ata_port_info pi = { 123 .flags = ATA_FLAG_SLAVE_POSS, 124 .pio_mask = ATA_PIO4, 125 .port_ops = &cs5520_port_ops, 126 }; 127 const struct ata_port_info *ppi[2]; 128 u8 pcicfg; 129 void __iomem *iomap[5]; 130 struct ata_host *host; 131 struct ata_ioports *ioaddr; 132 int i, rc; 133 134 rc = pcim_enable_device(pdev); 135 if (rc) 136 return rc; 137 138 /* IDE port enable bits */ 139 pci_read_config_byte(pdev, 0x60, &pcicfg); 140 141 /* Check if the ATA ports are enabled */ 142 if ((pcicfg & 3) == 0) 143 return -ENODEV; 144 145 ppi[0] = ppi[1] = &ata_dummy_port_info; 146 if (pcicfg & 1) 147 ppi[0] = π 148 if (pcicfg & 2) 149 ppi[1] = π 150 151 if ((pcicfg & 0x40) == 0) { 152 dev_warn(&pdev->dev, "DMA mode disabled. Enabling.\n"); 153 pci_write_config_byte(pdev, 0x60, pcicfg | 0x40); 154 } 155 156 pi.mwdma_mask = id->driver_data; 157 158 host = ata_host_alloc_pinfo(&pdev->dev, ppi, 2); 159 if (!host) 160 return -ENOMEM; 161 162 /* Perform set up for DMA */ 163 if (pci_enable_device_io(pdev)) { 164 printk(KERN_ERR DRV_NAME ": unable to configure BAR2.\n"); 165 return -ENODEV; 166 } 167 168 if (pci_set_dma_mask(pdev, DMA_BIT_MASK(32))) { 169 printk(KERN_ERR DRV_NAME ": unable to configure DMA mask.\n"); 170 return -ENODEV; 171 } 172 if (pci_set_consistent_dma_mask(pdev, DMA_BIT_MASK(32))) { 173 printk(KERN_ERR DRV_NAME ": unable to configure consistent DMA mask.\n"); 174 return -ENODEV; 175 } 176 177 /* Map IO ports and initialize host accordingly */ 178 iomap[0] = devm_ioport_map(&pdev->dev, cmd_port[0], 8); 179 iomap[1] = devm_ioport_map(&pdev->dev, ctl_port[0], 1); 180 iomap[2] = devm_ioport_map(&pdev->dev, cmd_port[1], 8); 181 iomap[3] = devm_ioport_map(&pdev->dev, ctl_port[1], 1); 182 iomap[4] = pcim_iomap(pdev, 2, 0); 183 184 if (!iomap[0] || !iomap[1] || !iomap[2] || !iomap[3] || !iomap[4]) 185 return -ENOMEM; 186 187 ioaddr = &host->ports[0]->ioaddr; 188 ioaddr->cmd_addr = iomap[0]; 189 ioaddr->ctl_addr = iomap[1]; 190 ioaddr->altstatus_addr = iomap[1]; 191 ioaddr->bmdma_addr = iomap[4]; 192 ata_sff_std_ports(ioaddr); 193 194 ata_port_desc(host->ports[0], 195 "cmd 0x%x ctl 0x%x", cmd_port[0], ctl_port[0]); 196 ata_port_pbar_desc(host->ports[0], 4, 0, "bmdma"); 197 198 ioaddr = &host->ports[1]->ioaddr; 199 ioaddr->cmd_addr = iomap[2]; 200 ioaddr->ctl_addr = iomap[3]; 201 ioaddr->altstatus_addr = iomap[3]; 202 ioaddr->bmdma_addr = iomap[4] + 8; 203 ata_sff_std_ports(ioaddr); 204 205 ata_port_desc(host->ports[1], 206 "cmd 0x%x ctl 0x%x", cmd_port[1], ctl_port[1]); 207 ata_port_pbar_desc(host->ports[1], 4, 8, "bmdma"); 208 209 /* activate the host */ 210 pci_set_master(pdev); 211 rc = ata_host_start(host); 212 if (rc) 213 return rc; 214 215 for (i = 0; i < 2; i++) { 216 static const int irq[] = { 14, 15 }; 217 struct ata_port *ap = host->ports[i]; 218 219 if (ata_port_is_dummy(ap)) 220 continue; 221 222 rc = devm_request_irq(&pdev->dev, irq[ap->port_no], 223 ata_bmdma_interrupt, 0, DRV_NAME, host); 224 if (rc) 225 return rc; 226 227 ata_port_desc(ap, "irq %d", irq[i]); 228 } 229 230 return ata_host_register(host, &cs5520_sht); 231 } 232 233 #ifdef CONFIG_PM 234 /** 235 * cs5520_reinit_one - device resume 236 * @pdev: PCI device 237 * 238 * Do any reconfiguration work needed by a resume from RAM. We need 239 * to restore DMA mode support on BIOSen which disabled it 240 */ 241 242 static int cs5520_reinit_one(struct pci_dev *pdev) 243 { 244 struct ata_host *host = dev_get_drvdata(&pdev->dev); 245 u8 pcicfg; 246 int rc; 247 248 rc = ata_pci_device_do_resume(pdev); 249 if (rc) 250 return rc; 251 252 pci_read_config_byte(pdev, 0x60, &pcicfg); 253 if ((pcicfg & 0x40) == 0) 254 pci_write_config_byte(pdev, 0x60, pcicfg | 0x40); 255 256 ata_host_resume(host); 257 return 0; 258 } 259 260 /** 261 * cs5520_pci_device_suspend - device suspend 262 * @pdev: PCI device 263 * 264 * We have to cut and waste bits from the standard method because 265 * the 5520 is a bit odd and not just a pure ATA device. As a result 266 * we must not disable it. The needed code is short and this avoids 267 * chip specific mess in the core code. 268 */ 269 270 static int cs5520_pci_device_suspend(struct pci_dev *pdev, pm_message_t mesg) 271 { 272 struct ata_host *host = dev_get_drvdata(&pdev->dev); 273 int rc = 0; 274 275 rc = ata_host_suspend(host, mesg); 276 if (rc) 277 return rc; 278 279 pci_save_state(pdev); 280 return 0; 281 } 282 #endif /* CONFIG_PM */ 283 284 /* For now keep DMA off. We can set it for all but A rev CS5510 once the 285 core ATA code can handle it */ 286 287 static const struct pci_device_id pata_cs5520[] = { 288 { PCI_VDEVICE(CYRIX, PCI_DEVICE_ID_CYRIX_5510), }, 289 { PCI_VDEVICE(CYRIX, PCI_DEVICE_ID_CYRIX_5520), }, 290 291 { }, 292 }; 293 294 static struct pci_driver cs5520_pci_driver = { 295 .name = DRV_NAME, 296 .id_table = pata_cs5520, 297 .probe = cs5520_init_one, 298 .remove = ata_pci_remove_one, 299 #ifdef CONFIG_PM 300 .suspend = cs5520_pci_device_suspend, 301 .resume = cs5520_reinit_one, 302 #endif 303 }; 304 305 module_pci_driver(cs5520_pci_driver); 306 307 MODULE_AUTHOR("Alan Cox"); 308 MODULE_DESCRIPTION("low-level driver for Cyrix CS5510/5520"); 309 MODULE_LICENSE("GPL"); 310 MODULE_DEVICE_TABLE(pci, pata_cs5520); 311 MODULE_VERSION(DRV_VERSION); 312