1 /* 2 * pata_artop.c - ARTOP ATA controller driver 3 * 4 * (C) 2006 Red Hat <alan@redhat.com> 5 * 6 * Based in part on drivers/ide/pci/aec62xx.c 7 * Copyright (C) 1999-2002 Andre Hedrick <andre@linux-ide.org> 8 * 865/865R fixes for Macintosh card version from a patch to the old 9 * driver by Thibaut VARENE <varenet@parisc-linux.org> 10 * When setting the PCI latency we must set 0x80 or higher for burst 11 * performance Alessandro Zummo <alessandro.zummo@towertech.it> 12 * 13 * TODO 14 * 850 serialization once the core supports it 15 * Investigate no_dsc on 850R 16 * Clock detect 17 */ 18 19 #include <linux/kernel.h> 20 #include <linux/module.h> 21 #include <linux/pci.h> 22 #include <linux/init.h> 23 #include <linux/blkdev.h> 24 #include <linux/delay.h> 25 #include <linux/device.h> 26 #include <scsi/scsi_host.h> 27 #include <linux/libata.h> 28 #include <linux/ata.h> 29 30 #define DRV_NAME "pata_artop" 31 #define DRV_VERSION "0.4.3" 32 33 /* 34 * The ARTOP has 33 Mhz and "over clocked" timing tables. Until we 35 * get PCI bus speed functionality we leave this as 0. Its a variable 36 * for when we get the functionality and also for folks wanting to 37 * test stuff. 38 */ 39 40 static int clock = 0; 41 42 static int artop6210_pre_reset(struct ata_port *ap, unsigned long deadline) 43 { 44 struct pci_dev *pdev = to_pci_dev(ap->host->dev); 45 const struct pci_bits artop_enable_bits[] = { 46 { 0x4AU, 1U, 0x02UL, 0x02UL }, /* port 0 */ 47 { 0x4AU, 1U, 0x04UL, 0x04UL }, /* port 1 */ 48 }; 49 50 if (!pci_test_config_bits(pdev, &artop_enable_bits[ap->port_no])) 51 return -ENOENT; 52 53 return ata_std_prereset(ap, deadline); 54 } 55 56 /** 57 * artop6210_error_handler - Probe specified port on PATA host controller 58 * @ap: Port to probe 59 * 60 * LOCKING: 61 * None (inherited from caller). 62 */ 63 64 static void artop6210_error_handler(struct ata_port *ap) 65 { 66 ata_bmdma_drive_eh(ap, artop6210_pre_reset, 67 ata_std_softreset, NULL, 68 ata_std_postreset); 69 } 70 71 /** 72 * artop6260_pre_reset - check for 40/80 pin 73 * @ap: Port 74 * @deadline: deadline jiffies for the operation 75 * 76 * The ARTOP hardware reports the cable detect bits in register 0x49. 77 * Nothing complicated needed here. 78 */ 79 80 static int artop6260_pre_reset(struct ata_port *ap, unsigned long deadline) 81 { 82 static const struct pci_bits artop_enable_bits[] = { 83 { 0x4AU, 1U, 0x02UL, 0x02UL }, /* port 0 */ 84 { 0x4AU, 1U, 0x04UL, 0x04UL }, /* port 1 */ 85 }; 86 87 struct pci_dev *pdev = to_pci_dev(ap->host->dev); 88 89 /* Odd numbered device ids are the units with enable bits (the -R cards) */ 90 if (pdev->device % 1 && !pci_test_config_bits(pdev, &artop_enable_bits[ap->port_no])) 91 return -ENOENT; 92 93 return ata_std_prereset(ap, deadline); 94 } 95 96 /** 97 * artop6260_cable_detect - identify cable type 98 * @ap: Port 99 * 100 * Identify the cable type for the ARTOP interface in question 101 */ 102 103 static int artop6260_cable_detect(struct ata_port *ap) 104 { 105 struct pci_dev *pdev = to_pci_dev(ap->host->dev); 106 u8 tmp; 107 pci_read_config_byte(pdev, 0x49, &tmp); 108 if (tmp & (1 << ap->port_no)) 109 return ATA_CBL_PATA40; 110 return ATA_CBL_PATA80; 111 } 112 113 /** 114 * artop6260_error_handler - Probe specified port on PATA host controller 115 * @ap: Port to probe 116 * 117 * LOCKING: 118 * None (inherited from caller). 119 */ 120 121 static void artop6260_error_handler(struct ata_port *ap) 122 { 123 ata_bmdma_drive_eh(ap, artop6260_pre_reset, 124 ata_std_softreset, NULL, 125 ata_std_postreset); 126 } 127 128 /** 129 * artop6210_load_piomode - Load a set of PATA PIO timings 130 * @ap: Port whose timings we are configuring 131 * @adev: Device 132 * @pio: PIO mode 133 * 134 * Set PIO mode for device, in host controller PCI config space. This 135 * is used both to set PIO timings in PIO mode and also to set the 136 * matching PIO clocking for UDMA, as well as the MWDMA timings. 137 * 138 * LOCKING: 139 * None (inherited from caller). 140 */ 141 142 static void artop6210_load_piomode(struct ata_port *ap, struct ata_device *adev, unsigned int pio) 143 { 144 struct pci_dev *pdev = to_pci_dev(ap->host->dev); 145 int dn = adev->devno + 2 * ap->port_no; 146 const u16 timing[2][5] = { 147 { 0x0000, 0x000A, 0x0008, 0x0303, 0x0301 }, 148 { 0x0700, 0x070A, 0x0708, 0x0403, 0x0401 } 149 150 }; 151 /* Load the PIO timing active/recovery bits */ 152 pci_write_config_word(pdev, 0x40 + 2 * dn, timing[clock][pio]); 153 } 154 155 /** 156 * artop6210_set_piomode - Initialize host controller PATA PIO timings 157 * @ap: Port whose timings we are configuring 158 * @adev: Device we are configuring 159 * 160 * Set PIO mode for device, in host controller PCI config space. For 161 * ARTOP we must also clear the UDMA bits if we are not doing UDMA. In 162 * the event UDMA is used the later call to set_dmamode will set the 163 * bits as required. 164 * 165 * LOCKING: 166 * None (inherited from caller). 167 */ 168 169 static void artop6210_set_piomode(struct ata_port *ap, struct ata_device *adev) 170 { 171 struct pci_dev *pdev = to_pci_dev(ap->host->dev); 172 int dn = adev->devno + 2 * ap->port_no; 173 u8 ultra; 174 175 artop6210_load_piomode(ap, adev, adev->pio_mode - XFER_PIO_0); 176 177 /* Clear the UDMA mode bits (set_dmamode will redo this if needed) */ 178 pci_read_config_byte(pdev, 0x54, &ultra); 179 ultra &= ~(3 << (2 * dn)); 180 pci_write_config_byte(pdev, 0x54, ultra); 181 } 182 183 /** 184 * artop6260_load_piomode - Initialize host controller PATA PIO timings 185 * @ap: Port whose timings we are configuring 186 * @adev: Device we are configuring 187 * @pio: PIO mode 188 * 189 * Set PIO mode for device, in host controller PCI config space. The 190 * ARTOP6260 and relatives store the timing data differently. 191 * 192 * LOCKING: 193 * None (inherited from caller). 194 */ 195 196 static void artop6260_load_piomode (struct ata_port *ap, struct ata_device *adev, unsigned int pio) 197 { 198 struct pci_dev *pdev = to_pci_dev(ap->host->dev); 199 int dn = adev->devno + 2 * ap->port_no; 200 const u8 timing[2][5] = { 201 { 0x00, 0x0A, 0x08, 0x33, 0x31 }, 202 { 0x70, 0x7A, 0x78, 0x43, 0x41 } 203 204 }; 205 /* Load the PIO timing active/recovery bits */ 206 pci_write_config_byte(pdev, 0x40 + dn, timing[clock][pio]); 207 } 208 209 /** 210 * artop6260_set_piomode - Initialize host controller PATA PIO timings 211 * @ap: Port whose timings we are configuring 212 * @adev: Device we are configuring 213 * 214 * Set PIO mode for device, in host controller PCI config space. For 215 * ARTOP we must also clear the UDMA bits if we are not doing UDMA. In 216 * the event UDMA is used the later call to set_dmamode will set the 217 * bits as required. 218 * 219 * LOCKING: 220 * None (inherited from caller). 221 */ 222 223 static void artop6260_set_piomode(struct ata_port *ap, struct ata_device *adev) 224 { 225 struct pci_dev *pdev = to_pci_dev(ap->host->dev); 226 u8 ultra; 227 228 artop6260_load_piomode(ap, adev, adev->pio_mode - XFER_PIO_0); 229 230 /* Clear the UDMA mode bits (set_dmamode will redo this if needed) */ 231 pci_read_config_byte(pdev, 0x44 + ap->port_no, &ultra); 232 ultra &= ~(7 << (4 * adev->devno)); /* One nibble per drive */ 233 pci_write_config_byte(pdev, 0x44 + ap->port_no, ultra); 234 } 235 236 /** 237 * artop6210_set_dmamode - Initialize host controller PATA PIO timings 238 * @ap: Port whose timings we are configuring 239 * @adev: Device whose timings we are configuring 240 * 241 * Set DMA mode for device, in host controller PCI config space. 242 * 243 * LOCKING: 244 * None (inherited from caller). 245 */ 246 247 static void artop6210_set_dmamode (struct ata_port *ap, struct ata_device *adev) 248 { 249 unsigned int pio; 250 struct pci_dev *pdev = to_pci_dev(ap->host->dev); 251 int dn = adev->devno + 2 * ap->port_no; 252 u8 ultra; 253 254 if (adev->dma_mode == XFER_MW_DMA_0) 255 pio = 1; 256 else 257 pio = 4; 258 259 /* Load the PIO timing active/recovery bits */ 260 artop6210_load_piomode(ap, adev, pio); 261 262 pci_read_config_byte(pdev, 0x54, &ultra); 263 ultra &= ~(3 << (2 * dn)); 264 265 /* Add ultra DMA bits if in UDMA mode */ 266 if (adev->dma_mode >= XFER_UDMA_0) { 267 u8 mode = (adev->dma_mode - XFER_UDMA_0) + 1 - clock; 268 if (mode == 0) 269 mode = 1; 270 ultra |= (mode << (2 * dn)); 271 } 272 pci_write_config_byte(pdev, 0x54, ultra); 273 } 274 275 /** 276 * artop6260_set_dmamode - Initialize host controller PATA PIO timings 277 * @ap: Port whose timings we are configuring 278 * @adev: Device we are configuring 279 * 280 * Set DMA mode for device, in host controller PCI config space. The 281 * ARTOP6260 and relatives store the timing data differently. 282 * 283 * LOCKING: 284 * None (inherited from caller). 285 */ 286 287 static void artop6260_set_dmamode (struct ata_port *ap, struct ata_device *adev) 288 { 289 unsigned int pio = adev->pio_mode - XFER_PIO_0; 290 struct pci_dev *pdev = to_pci_dev(ap->host->dev); 291 u8 ultra; 292 293 if (adev->dma_mode == XFER_MW_DMA_0) 294 pio = 1; 295 else 296 pio = 4; 297 298 /* Load the PIO timing active/recovery bits */ 299 artop6260_load_piomode(ap, adev, pio); 300 301 /* Add ultra DMA bits if in UDMA mode */ 302 pci_read_config_byte(pdev, 0x44 + ap->port_no, &ultra); 303 ultra &= ~(7 << (4 * adev->devno)); /* One nibble per drive */ 304 if (adev->dma_mode >= XFER_UDMA_0) { 305 u8 mode = adev->dma_mode - XFER_UDMA_0 + 1 - clock; 306 if (mode == 0) 307 mode = 1; 308 ultra |= (mode << (4 * adev->devno)); 309 } 310 pci_write_config_byte(pdev, 0x44 + ap->port_no, ultra); 311 } 312 313 static struct scsi_host_template artop_sht = { 314 .module = THIS_MODULE, 315 .name = DRV_NAME, 316 .ioctl = ata_scsi_ioctl, 317 .queuecommand = ata_scsi_queuecmd, 318 .can_queue = ATA_DEF_QUEUE, 319 .this_id = ATA_SHT_THIS_ID, 320 .sg_tablesize = LIBATA_MAX_PRD, 321 .cmd_per_lun = ATA_SHT_CMD_PER_LUN, 322 .emulated = ATA_SHT_EMULATED, 323 .use_clustering = ATA_SHT_USE_CLUSTERING, 324 .proc_name = DRV_NAME, 325 .dma_boundary = ATA_DMA_BOUNDARY, 326 .slave_configure = ata_scsi_slave_config, 327 .slave_destroy = ata_scsi_slave_destroy, 328 .bios_param = ata_std_bios_param, 329 }; 330 331 static const struct ata_port_operations artop6210_ops = { 332 .port_disable = ata_port_disable, 333 .set_piomode = artop6210_set_piomode, 334 .set_dmamode = artop6210_set_dmamode, 335 .mode_filter = ata_pci_default_filter, 336 337 .tf_load = ata_tf_load, 338 .tf_read = ata_tf_read, 339 .check_status = ata_check_status, 340 .exec_command = ata_exec_command, 341 .dev_select = ata_std_dev_select, 342 343 .freeze = ata_bmdma_freeze, 344 .thaw = ata_bmdma_thaw, 345 .error_handler = artop6210_error_handler, 346 .post_internal_cmd = ata_bmdma_post_internal_cmd, 347 .cable_detect = ata_cable_40wire, 348 349 .bmdma_setup = ata_bmdma_setup, 350 .bmdma_start = ata_bmdma_start, 351 .bmdma_stop = ata_bmdma_stop, 352 .bmdma_status = ata_bmdma_status, 353 .qc_prep = ata_qc_prep, 354 .qc_issue = ata_qc_issue_prot, 355 356 .data_xfer = ata_data_xfer, 357 358 .irq_handler = ata_interrupt, 359 .irq_clear = ata_bmdma_irq_clear, 360 .irq_on = ata_irq_on, 361 .irq_ack = ata_irq_ack, 362 363 .port_start = ata_port_start, 364 }; 365 366 static const struct ata_port_operations artop6260_ops = { 367 .port_disable = ata_port_disable, 368 .set_piomode = artop6260_set_piomode, 369 .set_dmamode = artop6260_set_dmamode, 370 371 .tf_load = ata_tf_load, 372 .tf_read = ata_tf_read, 373 .check_status = ata_check_status, 374 .exec_command = ata_exec_command, 375 .dev_select = ata_std_dev_select, 376 377 .freeze = ata_bmdma_freeze, 378 .thaw = ata_bmdma_thaw, 379 .error_handler = artop6260_error_handler, 380 .post_internal_cmd = ata_bmdma_post_internal_cmd, 381 .cable_detect = artop6260_cable_detect, 382 383 .bmdma_setup = ata_bmdma_setup, 384 .bmdma_start = ata_bmdma_start, 385 .bmdma_stop = ata_bmdma_stop, 386 .bmdma_status = ata_bmdma_status, 387 .qc_prep = ata_qc_prep, 388 .qc_issue = ata_qc_issue_prot, 389 .data_xfer = ata_data_xfer, 390 391 .irq_handler = ata_interrupt, 392 .irq_clear = ata_bmdma_irq_clear, 393 .irq_on = ata_irq_on, 394 .irq_ack = ata_irq_ack, 395 396 .port_start = ata_port_start, 397 }; 398 399 400 /** 401 * artop_init_one - Register ARTOP ATA PCI device with kernel services 402 * @pdev: PCI device to register 403 * @ent: Entry in artop_pci_tbl matching with @pdev 404 * 405 * Called from kernel PCI layer. 406 * 407 * LOCKING: 408 * Inherited from PCI layer (may sleep). 409 * 410 * RETURNS: 411 * Zero on success, or -ERRNO value. 412 */ 413 414 static int artop_init_one (struct pci_dev *pdev, const struct pci_device_id *id) 415 { 416 static int printed_version; 417 static const struct ata_port_info info_6210 = { 418 .sht = &artop_sht, 419 .flags = ATA_FLAG_SLAVE_POSS, 420 .pio_mask = 0x1f, /* pio0-4 */ 421 .mwdma_mask = 0x07, /* mwdma0-2 */ 422 .udma_mask = ATA_UDMA2, 423 .port_ops = &artop6210_ops, 424 }; 425 static const struct ata_port_info info_626x = { 426 .sht = &artop_sht, 427 .flags = ATA_FLAG_SLAVE_POSS, 428 .pio_mask = 0x1f, /* pio0-4 */ 429 .mwdma_mask = 0x07, /* mwdma0-2 */ 430 .udma_mask = ATA_UDMA4, 431 .port_ops = &artop6260_ops, 432 }; 433 static const struct ata_port_info info_626x_fast = { 434 .sht = &artop_sht, 435 .flags = ATA_FLAG_SLAVE_POSS, 436 .pio_mask = 0x1f, /* pio0-4 */ 437 .mwdma_mask = 0x07, /* mwdma0-2 */ 438 .udma_mask = ATA_UDMA5, 439 .port_ops = &artop6260_ops, 440 }; 441 const struct ata_port_info *ppi[] = { NULL, NULL }; 442 443 if (!printed_version++) 444 dev_printk(KERN_DEBUG, &pdev->dev, 445 "version " DRV_VERSION "\n"); 446 447 if (id->driver_data == 0) { /* 6210 variant */ 448 ppi[0] = &info_6210; 449 ppi[1] = &ata_dummy_port_info; 450 /* BIOS may have left us in UDMA, clear it before libata probe */ 451 pci_write_config_byte(pdev, 0x54, 0); 452 /* For the moment (also lacks dsc) */ 453 printk(KERN_WARNING "ARTOP 6210 requires serialize functionality not yet supported by libata.\n"); 454 printk(KERN_WARNING "Secondary ATA ports will not be activated.\n"); 455 } 456 else if (id->driver_data == 1) /* 6260 */ 457 ppi[0] = &info_626x; 458 else if (id->driver_data == 2) { /* 6260 or 6260 + fast */ 459 unsigned long io = pci_resource_start(pdev, 4); 460 u8 reg; 461 462 ppi[0] = &info_626x; 463 if (inb(io) & 0x10) 464 ppi[0] = &info_626x_fast; 465 /* Mac systems come up with some registers not set as we 466 will need them */ 467 468 /* Clear reset & test bits */ 469 pci_read_config_byte(pdev, 0x49, ®); 470 pci_write_config_byte(pdev, 0x49, reg & ~ 0x30); 471 472 /* PCI latency must be > 0x80 for burst mode, tweak it 473 * if required. 474 */ 475 pci_read_config_byte(pdev, PCI_LATENCY_TIMER, ®); 476 if (reg <= 0x80) 477 pci_write_config_byte(pdev, PCI_LATENCY_TIMER, 0x90); 478 479 /* Enable IRQ output and burst mode */ 480 pci_read_config_byte(pdev, 0x4a, ®); 481 pci_write_config_byte(pdev, 0x4a, (reg & ~0x01) | 0x80); 482 483 } 484 485 BUG_ON(ppi[0] == NULL); 486 487 return ata_pci_init_one(pdev, ppi); 488 } 489 490 static const struct pci_device_id artop_pci_tbl[] = { 491 { PCI_VDEVICE(ARTOP, 0x0005), 0 }, 492 { PCI_VDEVICE(ARTOP, 0x0006), 1 }, 493 { PCI_VDEVICE(ARTOP, 0x0007), 1 }, 494 { PCI_VDEVICE(ARTOP, 0x0008), 2 }, 495 { PCI_VDEVICE(ARTOP, 0x0009), 2 }, 496 497 { } /* terminate list */ 498 }; 499 500 static struct pci_driver artop_pci_driver = { 501 .name = DRV_NAME, 502 .id_table = artop_pci_tbl, 503 .probe = artop_init_one, 504 .remove = ata_pci_remove_one, 505 }; 506 507 static int __init artop_init(void) 508 { 509 return pci_register_driver(&artop_pci_driver); 510 } 511 512 static void __exit artop_exit(void) 513 { 514 pci_unregister_driver(&artop_pci_driver); 515 } 516 517 module_init(artop_init); 518 module_exit(artop_exit); 519 520 MODULE_AUTHOR("Alan Cox"); 521 MODULE_DESCRIPTION("SCSI low-level driver for ARTOP PATA"); 522 MODULE_LICENSE("GPL"); 523 MODULE_DEVICE_TABLE(pci, artop_pci_tbl); 524 MODULE_VERSION(DRV_VERSION); 525 526