1 // SPDX-License-Identifier: GPL-2.0-or-later
2 /*
3 * Broadcom SATA3 AHCI Controller Driver
4 *
5 * Copyright © 2009-2015 Broadcom Corporation
6 */
7
8 #include <linux/ahci_platform.h>
9 #include <linux/compiler.h>
10 #include <linux/device.h>
11 #include <linux/init.h>
12 #include <linux/interrupt.h>
13 #include <linux/io.h>
14 #include <linux/kernel.h>
15 #include <linux/libata.h>
16 #include <linux/module.h>
17 #include <linux/of.h>
18 #include <linux/platform_device.h>
19 #include <linux/reset.h>
20 #include <linux/string.h>
21
22 #include "ahci.h"
23
24 #define DRV_NAME "brcm-ahci"
25
26 #define SATA_TOP_CTRL_VERSION 0x0
27 #define SATA_TOP_CTRL_BUS_CTRL 0x4
28 #define MMIO_ENDIAN_SHIFT 0 /* CPU->AHCI */
29 #define DMADESC_ENDIAN_SHIFT 2 /* AHCI->DDR */
30 #define DMADATA_ENDIAN_SHIFT 4 /* AHCI->DDR */
31 #define PIODATA_ENDIAN_SHIFT 6
32 #define ENDIAN_SWAP_NONE 0
33 #define ENDIAN_SWAP_FULL 2
34 #define SATA_TOP_CTRL_TP_CTRL 0x8
35 #define SATA_TOP_CTRL_PHY_CTRL 0xc
36 #define SATA_TOP_CTRL_PHY_CTRL_1 0x0
37 #define SATA_TOP_CTRL_1_PHY_DEFAULT_POWER_STATE BIT(14)
38 #define SATA_TOP_CTRL_PHY_CTRL_2 0x4
39 #define SATA_TOP_CTRL_2_SW_RST_MDIOREG BIT(0)
40 #define SATA_TOP_CTRL_2_SW_RST_OOB BIT(1)
41 #define SATA_TOP_CTRL_2_SW_RST_RX BIT(2)
42 #define SATA_TOP_CTRL_2_SW_RST_TX BIT(3)
43 #define SATA_TOP_CTRL_2_PHY_GLOBAL_RESET BIT(14)
44 #define SATA_TOP_CTRL_PHY_OFFS 0x8
45 #define SATA_TOP_MAX_PHYS 2
46
47 #define SATA_FIRST_PORT_CTRL 0x700
48 #define SATA_NEXT_PORT_CTRL_OFFSET 0x80
49 #define SATA_PORT_PCTRL6(reg_base) (reg_base + 0x18)
50
51 /* On big-endian MIPS, buses are reversed to big endian, so switch them back */
52 #if defined(CONFIG_MIPS) && defined(__BIG_ENDIAN)
53 #define DATA_ENDIAN 2 /* AHCI->DDR inbound accesses */
54 #define MMIO_ENDIAN 2 /* CPU->AHCI outbound accesses */
55 #else
56 #define DATA_ENDIAN 0
57 #define MMIO_ENDIAN 0
58 #endif
59
60 #define BUS_CTRL_ENDIAN_CONF \
61 ((DATA_ENDIAN << DMADATA_ENDIAN_SHIFT) | \
62 (DATA_ENDIAN << DMADESC_ENDIAN_SHIFT) | \
63 (MMIO_ENDIAN << MMIO_ENDIAN_SHIFT))
64
65 #define BUS_CTRL_ENDIAN_NSP_CONF \
66 (0x02 << DMADATA_ENDIAN_SHIFT | 0x02 << DMADESC_ENDIAN_SHIFT)
67
68 #define BUS_CTRL_ENDIAN_CONF_MASK \
69 (0x3 << MMIO_ENDIAN_SHIFT | 0x3 << DMADESC_ENDIAN_SHIFT | \
70 0x3 << DMADATA_ENDIAN_SHIFT | 0x3 << PIODATA_ENDIAN_SHIFT)
71
72 enum brcm_ahci_version {
73 BRCM_SATA_BCM7425 = 1,
74 BRCM_SATA_BCM7445,
75 BRCM_SATA_NSP,
76 BRCM_SATA_BCM7216,
77 };
78
79 enum brcm_ahci_quirks {
80 BRCM_AHCI_QUIRK_SKIP_PHY_ENABLE = BIT(0),
81 };
82
83 struct brcm_ahci_priv {
84 struct device *dev;
85 void __iomem *top_ctrl;
86 u32 port_mask;
87 u32 quirks;
88 enum brcm_ahci_version version;
89 struct reset_control *rcdev_rescal;
90 struct reset_control *rcdev_ahci;
91 };
92
brcm_sata_readreg(void __iomem * addr)93 static inline u32 brcm_sata_readreg(void __iomem *addr)
94 {
95 /*
96 * MIPS endianness is configured by boot strap, which also reverses all
97 * bus endianness (i.e., big-endian CPU + big endian bus ==> native
98 * endian I/O).
99 *
100 * Other architectures (e.g., ARM) either do not support big endian, or
101 * else leave I/O in little endian mode.
102 */
103 if (IS_ENABLED(CONFIG_MIPS) && IS_ENABLED(CONFIG_CPU_BIG_ENDIAN))
104 return __raw_readl(addr);
105 else
106 return readl_relaxed(addr);
107 }
108
brcm_sata_writereg(u32 val,void __iomem * addr)109 static inline void brcm_sata_writereg(u32 val, void __iomem *addr)
110 {
111 /* See brcm_sata_readreg() comments */
112 if (IS_ENABLED(CONFIG_MIPS) && IS_ENABLED(CONFIG_CPU_BIG_ENDIAN))
113 __raw_writel(val, addr);
114 else
115 writel_relaxed(val, addr);
116 }
117
brcm_sata_alpm_init(struct ahci_host_priv * hpriv)118 static void brcm_sata_alpm_init(struct ahci_host_priv *hpriv)
119 {
120 struct brcm_ahci_priv *priv = hpriv->plat_data;
121 u32 port_ctrl, host_caps;
122 int i;
123
124 /* Enable support for ALPM */
125 host_caps = readl(hpriv->mmio + HOST_CAP);
126 if (!(host_caps & HOST_CAP_ALPM))
127 hpriv->flags |= AHCI_HFLAG_YES_ALPM;
128
129 /*
130 * Adjust timeout to allow PLL sufficient time to lock while waking
131 * up from slumber mode.
132 */
133 for (i = 0, port_ctrl = SATA_FIRST_PORT_CTRL;
134 i < SATA_TOP_MAX_PHYS;
135 i++, port_ctrl += SATA_NEXT_PORT_CTRL_OFFSET) {
136 if (priv->port_mask & BIT(i))
137 writel(0xff1003fc,
138 hpriv->mmio + SATA_PORT_PCTRL6(port_ctrl));
139 }
140 }
141
brcm_sata_phy_enable(struct brcm_ahci_priv * priv,int port)142 static void brcm_sata_phy_enable(struct brcm_ahci_priv *priv, int port)
143 {
144 void __iomem *phyctrl = priv->top_ctrl + SATA_TOP_CTRL_PHY_CTRL +
145 (port * SATA_TOP_CTRL_PHY_OFFS);
146 void __iomem *p;
147 u32 reg;
148
149 if (priv->quirks & BRCM_AHCI_QUIRK_SKIP_PHY_ENABLE)
150 return;
151
152 /* clear PHY_DEFAULT_POWER_STATE */
153 p = phyctrl + SATA_TOP_CTRL_PHY_CTRL_1;
154 reg = brcm_sata_readreg(p);
155 reg &= ~SATA_TOP_CTRL_1_PHY_DEFAULT_POWER_STATE;
156 brcm_sata_writereg(reg, p);
157
158 /* reset the PHY digital logic */
159 p = phyctrl + SATA_TOP_CTRL_PHY_CTRL_2;
160 reg = brcm_sata_readreg(p);
161 reg &= ~(SATA_TOP_CTRL_2_SW_RST_MDIOREG | SATA_TOP_CTRL_2_SW_RST_OOB |
162 SATA_TOP_CTRL_2_SW_RST_RX);
163 reg |= SATA_TOP_CTRL_2_SW_RST_TX;
164 brcm_sata_writereg(reg, p);
165 reg = brcm_sata_readreg(p);
166 reg |= SATA_TOP_CTRL_2_PHY_GLOBAL_RESET;
167 brcm_sata_writereg(reg, p);
168 reg = brcm_sata_readreg(p);
169 reg &= ~SATA_TOP_CTRL_2_PHY_GLOBAL_RESET;
170 brcm_sata_writereg(reg, p);
171 (void)brcm_sata_readreg(p);
172 }
173
brcm_sata_phy_disable(struct brcm_ahci_priv * priv,int port)174 static void brcm_sata_phy_disable(struct brcm_ahci_priv *priv, int port)
175 {
176 void __iomem *phyctrl = priv->top_ctrl + SATA_TOP_CTRL_PHY_CTRL +
177 (port * SATA_TOP_CTRL_PHY_OFFS);
178 void __iomem *p;
179 u32 reg;
180
181 if (priv->quirks & BRCM_AHCI_QUIRK_SKIP_PHY_ENABLE)
182 return;
183
184 /* power-off the PHY digital logic */
185 p = phyctrl + SATA_TOP_CTRL_PHY_CTRL_2;
186 reg = brcm_sata_readreg(p);
187 reg |= (SATA_TOP_CTRL_2_SW_RST_MDIOREG | SATA_TOP_CTRL_2_SW_RST_OOB |
188 SATA_TOP_CTRL_2_SW_RST_RX | SATA_TOP_CTRL_2_SW_RST_TX |
189 SATA_TOP_CTRL_2_PHY_GLOBAL_RESET);
190 brcm_sata_writereg(reg, p);
191
192 /* set PHY_DEFAULT_POWER_STATE */
193 p = phyctrl + SATA_TOP_CTRL_PHY_CTRL_1;
194 reg = brcm_sata_readreg(p);
195 reg |= SATA_TOP_CTRL_1_PHY_DEFAULT_POWER_STATE;
196 brcm_sata_writereg(reg, p);
197 }
198
brcm_sata_phys_enable(struct brcm_ahci_priv * priv)199 static void brcm_sata_phys_enable(struct brcm_ahci_priv *priv)
200 {
201 int i;
202
203 for (i = 0; i < SATA_TOP_MAX_PHYS; i++)
204 if (priv->port_mask & BIT(i))
205 brcm_sata_phy_enable(priv, i);
206 }
207
brcm_sata_phys_disable(struct brcm_ahci_priv * priv)208 static void brcm_sata_phys_disable(struct brcm_ahci_priv *priv)
209 {
210 int i;
211
212 for (i = 0; i < SATA_TOP_MAX_PHYS; i++)
213 if (priv->port_mask & BIT(i))
214 brcm_sata_phy_disable(priv, i);
215 }
216
brcm_ahci_get_portmask(struct ahci_host_priv * hpriv,struct brcm_ahci_priv * priv)217 static u32 brcm_ahci_get_portmask(struct ahci_host_priv *hpriv,
218 struct brcm_ahci_priv *priv)
219 {
220 u32 impl;
221
222 impl = readl(hpriv->mmio + HOST_PORTS_IMPL);
223
224 if (fls(impl) > SATA_TOP_MAX_PHYS)
225 dev_warn(priv->dev, "warning: more ports than PHYs (%#x)\n",
226 impl);
227 else if (!impl)
228 dev_info(priv->dev, "no ports found\n");
229
230 return impl;
231 }
232
brcm_sata_init(struct brcm_ahci_priv * priv)233 static void brcm_sata_init(struct brcm_ahci_priv *priv)
234 {
235 void __iomem *ctrl = priv->top_ctrl + SATA_TOP_CTRL_BUS_CTRL;
236 u32 data;
237
238 /* Configure endianness */
239 data = brcm_sata_readreg(ctrl);
240 data &= ~BUS_CTRL_ENDIAN_CONF_MASK;
241 if (priv->version == BRCM_SATA_NSP)
242 data |= BUS_CTRL_ENDIAN_NSP_CONF;
243 else
244 data |= BUS_CTRL_ENDIAN_CONF;
245 brcm_sata_writereg(data, ctrl);
246 }
247
brcm_ahci_read_id(struct ata_device * dev,struct ata_taskfile * tf,__le16 * id)248 static unsigned int brcm_ahci_read_id(struct ata_device *dev,
249 struct ata_taskfile *tf, __le16 *id)
250 {
251 struct ata_port *ap = dev->link->ap;
252 struct ata_host *host = ap->host;
253 struct ahci_host_priv *hpriv = host->private_data;
254 struct brcm_ahci_priv *priv = hpriv->plat_data;
255 void __iomem *mmio = hpriv->mmio;
256 unsigned int err_mask;
257 unsigned long flags;
258 int i, rc;
259 u32 ctl;
260
261 /* Try to read the device ID and, if this fails, proceed with the
262 * recovery sequence below
263 */
264 err_mask = ata_do_dev_read_id(dev, tf, id);
265 if (likely(!err_mask))
266 return err_mask;
267
268 /* Disable host interrupts */
269 spin_lock_irqsave(&host->lock, flags);
270 ctl = readl(mmio + HOST_CTL);
271 ctl &= ~HOST_IRQ_EN;
272 writel(ctl, mmio + HOST_CTL);
273 readl(mmio + HOST_CTL); /* flush */
274 spin_unlock_irqrestore(&host->lock, flags);
275
276 /* Perform the SATA PHY reset sequence */
277 brcm_sata_phy_disable(priv, ap->port_no);
278
279 /* Reset the SATA clock */
280 ahci_platform_disable_clks(hpriv);
281 msleep(10);
282
283 ahci_platform_enable_clks(hpriv);
284 msleep(10);
285
286 /* Bring the PHY back on */
287 brcm_sata_phy_enable(priv, ap->port_no);
288
289 /* Re-initialize and calibrate the PHY */
290 for (i = 0; i < hpriv->nports; i++) {
291 rc = phy_init(hpriv->phys[i]);
292 if (rc)
293 goto disable_phys;
294
295 rc = phy_calibrate(hpriv->phys[i]);
296 if (rc) {
297 phy_exit(hpriv->phys[i]);
298 goto disable_phys;
299 }
300 }
301
302 /* Re-enable host interrupts */
303 spin_lock_irqsave(&host->lock, flags);
304 ctl = readl(mmio + HOST_CTL);
305 ctl |= HOST_IRQ_EN;
306 writel(ctl, mmio + HOST_CTL);
307 readl(mmio + HOST_CTL); /* flush */
308 spin_unlock_irqrestore(&host->lock, flags);
309
310 return ata_do_dev_read_id(dev, tf, id);
311
312 disable_phys:
313 while (--i >= 0) {
314 phy_power_off(hpriv->phys[i]);
315 phy_exit(hpriv->phys[i]);
316 }
317
318 return AC_ERR_OTHER;
319 }
320
brcm_ahci_host_stop(struct ata_host * host)321 static void brcm_ahci_host_stop(struct ata_host *host)
322 {
323 struct ahci_host_priv *hpriv = host->private_data;
324
325 ahci_platform_disable_resources(hpriv);
326 }
327
328 static struct ata_port_operations ahci_brcm_platform_ops = {
329 .inherits = &ahci_ops,
330 .host_stop = brcm_ahci_host_stop,
331 .read_id = brcm_ahci_read_id,
332 };
333
334 static const struct ata_port_info ahci_brcm_port_info = {
335 .flags = AHCI_FLAG_COMMON | ATA_FLAG_NO_DIPM,
336 .link_flags = ATA_LFLAG_NO_DEBOUNCE_DELAY,
337 .pio_mask = ATA_PIO4,
338 .udma_mask = ATA_UDMA6,
339 .port_ops = &ahci_brcm_platform_ops,
340 };
341
brcm_ahci_suspend(struct device * dev)342 static int brcm_ahci_suspend(struct device *dev)
343 {
344 struct ata_host *host = dev_get_drvdata(dev);
345 struct ahci_host_priv *hpriv = host->private_data;
346 struct brcm_ahci_priv *priv = hpriv->plat_data;
347 int ret;
348
349 brcm_sata_phys_disable(priv);
350
351 if (IS_ENABLED(CONFIG_PM_SLEEP))
352 ret = ahci_platform_suspend(dev);
353 else
354 ret = 0;
355
356 reset_control_assert(priv->rcdev_ahci);
357 reset_control_rearm(priv->rcdev_rescal);
358
359 return ret;
360 }
361
brcm_ahci_resume(struct device * dev)362 static int __maybe_unused brcm_ahci_resume(struct device *dev)
363 {
364 struct ata_host *host = dev_get_drvdata(dev);
365 struct ahci_host_priv *hpriv = host->private_data;
366 struct brcm_ahci_priv *priv = hpriv->plat_data;
367 int ret = 0;
368
369 ret = reset_control_deassert(priv->rcdev_ahci);
370 if (ret)
371 return ret;
372 ret = reset_control_reset(priv->rcdev_rescal);
373 if (ret)
374 return ret;
375
376 /* Make sure clocks are turned on before re-configuration */
377 ret = ahci_platform_enable_clks(hpriv);
378 if (ret)
379 return ret;
380
381 ret = ahci_platform_enable_regulators(hpriv);
382 if (ret)
383 goto out_disable_clks;
384
385 brcm_sata_init(priv);
386 brcm_sata_phys_enable(priv);
387 brcm_sata_alpm_init(hpriv);
388
389 /* Since we had to enable clocks earlier on, we cannot use
390 * ahci_platform_resume() as-is since a second call to
391 * ahci_platform_enable_resources() would bump up the resources
392 * (regulators, clocks, PHYs) count artificially so we copy the part
393 * after ahci_platform_enable_resources().
394 */
395 ret = ahci_platform_enable_phys(hpriv);
396 if (ret)
397 goto out_disable_phys;
398
399 ret = ahci_platform_resume_host(dev);
400 if (ret)
401 goto out_disable_platform_phys;
402
403 /* We resumed so update PM runtime state */
404 pm_runtime_disable(dev);
405 pm_runtime_set_active(dev);
406 pm_runtime_enable(dev);
407
408 return 0;
409
410 out_disable_platform_phys:
411 ahci_platform_disable_phys(hpriv);
412 out_disable_phys:
413 brcm_sata_phys_disable(priv);
414 ahci_platform_disable_regulators(hpriv);
415 out_disable_clks:
416 ahci_platform_disable_clks(hpriv);
417 return ret;
418 }
419
420 static const struct scsi_host_template ahci_platform_sht = {
421 AHCI_SHT(DRV_NAME),
422 };
423
424 static const struct of_device_id ahci_of_match[] = {
425 {.compatible = "brcm,bcm7425-ahci", .data = (void *)BRCM_SATA_BCM7425},
426 {.compatible = "brcm,bcm7445-ahci", .data = (void *)BRCM_SATA_BCM7445},
427 {.compatible = "brcm,bcm63138-ahci", .data = (void *)BRCM_SATA_BCM7445},
428 {.compatible = "brcm,bcm-nsp-ahci", .data = (void *)BRCM_SATA_NSP},
429 {.compatible = "brcm,bcm7216-ahci", .data = (void *)BRCM_SATA_BCM7216},
430 { /* sentinel */ }
431 };
432 MODULE_DEVICE_TABLE(of, ahci_of_match);
433
brcm_ahci_probe(struct platform_device * pdev)434 static int brcm_ahci_probe(struct platform_device *pdev)
435 {
436 const struct of_device_id *of_id;
437 struct device *dev = &pdev->dev;
438 struct brcm_ahci_priv *priv;
439 struct ahci_host_priv *hpriv;
440 struct resource *res;
441 int ret;
442
443 priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
444 if (!priv)
445 return -ENOMEM;
446
447 of_id = of_match_node(ahci_of_match, pdev->dev.of_node);
448 if (!of_id)
449 return -ENODEV;
450
451 priv->version = (unsigned long)of_id->data;
452 priv->dev = dev;
453
454 res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "top-ctrl");
455 priv->top_ctrl = devm_ioremap_resource(dev, res);
456 if (IS_ERR(priv->top_ctrl))
457 return PTR_ERR(priv->top_ctrl);
458
459 if (priv->version == BRCM_SATA_BCM7216) {
460 priv->rcdev_rescal = devm_reset_control_get_optional_shared(
461 &pdev->dev, "rescal");
462 if (IS_ERR(priv->rcdev_rescal))
463 return PTR_ERR(priv->rcdev_rescal);
464 }
465 priv->rcdev_ahci = devm_reset_control_get_optional(&pdev->dev, "ahci");
466 if (IS_ERR(priv->rcdev_ahci))
467 return PTR_ERR(priv->rcdev_ahci);
468
469 hpriv = ahci_platform_get_resources(pdev, 0);
470 if (IS_ERR(hpriv))
471 return PTR_ERR(hpriv);
472
473 hpriv->plat_data = priv;
474 hpriv->flags = AHCI_HFLAG_WAKE_BEFORE_STOP | AHCI_HFLAG_NO_WRITE_TO_RO;
475
476 switch (priv->version) {
477 case BRCM_SATA_BCM7425:
478 hpriv->flags |= AHCI_HFLAG_DELAY_ENGINE;
479 fallthrough;
480 case BRCM_SATA_NSP:
481 hpriv->flags |= AHCI_HFLAG_NO_NCQ;
482 priv->quirks |= BRCM_AHCI_QUIRK_SKIP_PHY_ENABLE;
483 break;
484 default:
485 break;
486 }
487
488 ret = reset_control_reset(priv->rcdev_rescal);
489 if (ret)
490 return ret;
491 ret = reset_control_deassert(priv->rcdev_ahci);
492 if (ret)
493 return ret;
494
495 ret = ahci_platform_enable_clks(hpriv);
496 if (ret)
497 goto out_reset;
498
499 ret = ahci_platform_enable_regulators(hpriv);
500 if (ret)
501 goto out_disable_clks;
502
503 /* Must be first so as to configure endianness including that
504 * of the standard AHCI register space.
505 */
506 brcm_sata_init(priv);
507
508 /* Initializes priv->port_mask which is used below */
509 priv->port_mask = brcm_ahci_get_portmask(hpriv, priv);
510 if (!priv->port_mask) {
511 ret = -ENODEV;
512 goto out_disable_regulators;
513 }
514
515 /* Must be done before ahci_platform_enable_phys() */
516 brcm_sata_phys_enable(priv);
517
518 brcm_sata_alpm_init(hpriv);
519
520 ret = ahci_platform_enable_phys(hpriv);
521 if (ret)
522 goto out_disable_phys;
523
524 ret = ahci_platform_init_host(pdev, hpriv, &ahci_brcm_port_info,
525 &ahci_platform_sht);
526 if (ret)
527 goto out_disable_platform_phys;
528
529 dev_info(dev, "Broadcom AHCI SATA3 registered\n");
530
531 return 0;
532
533 out_disable_platform_phys:
534 ahci_platform_disable_phys(hpriv);
535 out_disable_phys:
536 brcm_sata_phys_disable(priv);
537 out_disable_regulators:
538 ahci_platform_disable_regulators(hpriv);
539 out_disable_clks:
540 ahci_platform_disable_clks(hpriv);
541 out_reset:
542 reset_control_assert(priv->rcdev_ahci);
543 reset_control_rearm(priv->rcdev_rescal);
544 return ret;
545 }
546
brcm_ahci_remove(struct platform_device * pdev)547 static void brcm_ahci_remove(struct platform_device *pdev)
548 {
549 struct ata_host *host = dev_get_drvdata(&pdev->dev);
550 struct ahci_host_priv *hpriv = host->private_data;
551 struct brcm_ahci_priv *priv = hpriv->plat_data;
552
553 brcm_sata_phys_disable(priv);
554
555 ata_platform_remove_one(pdev);
556 }
557
brcm_ahci_shutdown(struct platform_device * pdev)558 static void brcm_ahci_shutdown(struct platform_device *pdev)
559 {
560 int ret;
561
562 /* All resources releasing happens via devres, but our device, unlike a
563 * proper remove is not disappearing, therefore using
564 * brcm_ahci_suspend() here which does explicit power management is
565 * appropriate.
566 */
567 ret = brcm_ahci_suspend(&pdev->dev);
568 if (ret)
569 dev_err(&pdev->dev, "failed to shutdown\n");
570 }
571
572 static SIMPLE_DEV_PM_OPS(ahci_brcm_pm_ops, brcm_ahci_suspend, brcm_ahci_resume);
573
574 static struct platform_driver brcm_ahci_driver = {
575 .probe = brcm_ahci_probe,
576 .remove_new = brcm_ahci_remove,
577 .shutdown = brcm_ahci_shutdown,
578 .driver = {
579 .name = DRV_NAME,
580 .of_match_table = ahci_of_match,
581 .pm = &ahci_brcm_pm_ops,
582 },
583 };
584 module_platform_driver(brcm_ahci_driver);
585
586 MODULE_DESCRIPTION("Broadcom SATA3 AHCI Controller Driver");
587 MODULE_AUTHOR("Brian Norris");
588 MODULE_LICENSE("GPL");
589 MODULE_ALIAS("platform:sata-brcmstb");
590