1 2 /****************************************************************************** 3 * 4 * Module Name: hwxface - Public ACPICA hardware interfaces 5 * 6 *****************************************************************************/ 7 8 /* 9 * Copyright (C) 2000 - 2010, Intel Corp. 10 * All rights reserved. 11 * 12 * Redistribution and use in source and binary forms, with or without 13 * modification, are permitted provided that the following conditions 14 * are met: 15 * 1. Redistributions of source code must retain the above copyright 16 * notice, this list of conditions, and the following disclaimer, 17 * without modification. 18 * 2. Redistributions in binary form must reproduce at minimum a disclaimer 19 * substantially similar to the "NO WARRANTY" disclaimer below 20 * ("Disclaimer") and any redistribution must be conditioned upon 21 * including a substantially similar Disclaimer requirement for further 22 * binary redistribution. 23 * 3. Neither the names of the above-listed copyright holders nor the names 24 * of any contributors may be used to endorse or promote products derived 25 * from this software without specific prior written permission. 26 * 27 * Alternatively, this software may be distributed under the terms of the 28 * GNU General Public License ("GPL") version 2 as published by the Free 29 * Software Foundation. 30 * 31 * NO WARRANTY 32 * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS 33 * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT 34 * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTIBILITY AND FITNESS FOR 35 * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT 36 * HOLDERS OR CONTRIBUTORS BE LIABLE FOR SPECIAL, EXEMPLARY, OR CONSEQUENTIAL 37 * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS 38 * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) 39 * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, 40 * STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING 41 * IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE 42 * POSSIBILITY OF SUCH DAMAGES. 43 */ 44 45 #include <acpi/acpi.h> 46 #include "accommon.h" 47 #include "acnamesp.h" 48 49 #define _COMPONENT ACPI_HARDWARE 50 ACPI_MODULE_NAME("hwxface") 51 52 /****************************************************************************** 53 * 54 * FUNCTION: acpi_reset 55 * 56 * PARAMETERS: None 57 * 58 * RETURN: Status 59 * 60 * DESCRIPTION: Set reset register in memory or IO space. Note: Does not 61 * support reset register in PCI config space, this must be 62 * handled separately. 63 * 64 ******************************************************************************/ 65 acpi_status acpi_reset(void) 66 { 67 struct acpi_generic_address *reset_reg; 68 acpi_status status; 69 70 ACPI_FUNCTION_TRACE(acpi_reset); 71 72 reset_reg = &acpi_gbl_FADT.reset_register; 73 74 /* Check if the reset register is supported */ 75 76 if (!(acpi_gbl_FADT.flags & ACPI_FADT_RESET_REGISTER) || 77 !reset_reg->address) { 78 return_ACPI_STATUS(AE_NOT_EXIST); 79 } 80 81 if (reset_reg->space_id == ACPI_ADR_SPACE_SYSTEM_IO) { 82 /* 83 * For I/O space, write directly to the OSL. This bypasses the port 84 * validation mechanism, which may block a valid write to the reset 85 * register. 86 */ 87 status = 88 acpi_os_write_port((acpi_io_address) reset_reg->address, 89 acpi_gbl_FADT.reset_value, 90 reset_reg->bit_width); 91 } else { 92 /* Write the reset value to the reset register */ 93 94 status = acpi_hw_write(acpi_gbl_FADT.reset_value, reset_reg); 95 } 96 97 return_ACPI_STATUS(status); 98 } 99 100 ACPI_EXPORT_SYMBOL(acpi_reset) 101 102 /****************************************************************************** 103 * 104 * FUNCTION: acpi_read 105 * 106 * PARAMETERS: Value - Where the value is returned 107 * Reg - GAS register structure 108 * 109 * RETURN: Status 110 * 111 * DESCRIPTION: Read from either memory or IO space. 112 * 113 * LIMITATIONS: <These limitations also apply to acpi_write> 114 * bit_width must be exactly 8, 16, 32, or 64. 115 * space_iD must be system_memory or system_iO. 116 * bit_offset and access_width are currently ignored, as there has 117 * not been a need to implement these. 118 * 119 ******************************************************************************/ 120 acpi_status acpi_read(u64 *return_value, struct acpi_generic_address *reg) 121 { 122 u32 value; 123 u32 width; 124 u64 address; 125 acpi_status status; 126 127 ACPI_FUNCTION_NAME(acpi_read); 128 129 if (!return_value) { 130 return (AE_BAD_PARAMETER); 131 } 132 133 /* Validate contents of the GAS register. Allow 64-bit transfers */ 134 135 status = acpi_hw_validate_register(reg, 64, &address); 136 if (ACPI_FAILURE(status)) { 137 return (status); 138 } 139 140 width = reg->bit_width; 141 if (width == 64) { 142 width = 32; /* Break into two 32-bit transfers */ 143 } 144 145 /* Initialize entire 64-bit return value to zero */ 146 147 *return_value = 0; 148 value = 0; 149 150 /* 151 * Two address spaces supported: Memory or IO. PCI_Config is 152 * not supported here because the GAS structure is insufficient 153 */ 154 if (reg->space_id == ACPI_ADR_SPACE_SYSTEM_MEMORY) { 155 status = acpi_os_read_memory((acpi_physical_address) 156 address, &value, width); 157 if (ACPI_FAILURE(status)) { 158 return (status); 159 } 160 *return_value = value; 161 162 if (reg->bit_width == 64) { 163 164 /* Read the top 32 bits */ 165 166 status = acpi_os_read_memory((acpi_physical_address) 167 (address + 4), &value, 32); 168 if (ACPI_FAILURE(status)) { 169 return (status); 170 } 171 *return_value |= ((u64)value << 32); 172 } 173 } else { /* ACPI_ADR_SPACE_SYSTEM_IO, validated earlier */ 174 175 status = acpi_hw_read_port((acpi_io_address) 176 address, &value, width); 177 if (ACPI_FAILURE(status)) { 178 return (status); 179 } 180 *return_value = value; 181 182 if (reg->bit_width == 64) { 183 184 /* Read the top 32 bits */ 185 186 status = acpi_hw_read_port((acpi_io_address) 187 (address + 4), &value, 32); 188 if (ACPI_FAILURE(status)) { 189 return (status); 190 } 191 *return_value |= ((u64)value << 32); 192 } 193 } 194 195 ACPI_DEBUG_PRINT((ACPI_DB_IO, 196 "Read: %8.8X%8.8X width %2d from %8.8X%8.8X (%s)\n", 197 ACPI_FORMAT_UINT64(*return_value), reg->bit_width, 198 ACPI_FORMAT_UINT64(address), 199 acpi_ut_get_region_name(reg->space_id))); 200 201 return (status); 202 } 203 204 ACPI_EXPORT_SYMBOL(acpi_read) 205 206 /****************************************************************************** 207 * 208 * FUNCTION: acpi_write 209 * 210 * PARAMETERS: Value - Value to be written 211 * Reg - GAS register structure 212 * 213 * RETURN: Status 214 * 215 * DESCRIPTION: Write to either memory or IO space. 216 * 217 ******************************************************************************/ 218 acpi_status acpi_write(u64 value, struct acpi_generic_address *reg) 219 { 220 u32 width; 221 u64 address; 222 acpi_status status; 223 224 ACPI_FUNCTION_NAME(acpi_write); 225 226 /* Validate contents of the GAS register. Allow 64-bit transfers */ 227 228 status = acpi_hw_validate_register(reg, 64, &address); 229 if (ACPI_FAILURE(status)) { 230 return (status); 231 } 232 233 width = reg->bit_width; 234 if (width == 64) { 235 width = 32; /* Break into two 32-bit transfers */ 236 } 237 238 /* 239 * Two address spaces supported: Memory or IO. PCI_Config is 240 * not supported here because the GAS structure is insufficient 241 */ 242 if (reg->space_id == ACPI_ADR_SPACE_SYSTEM_MEMORY) { 243 status = acpi_os_write_memory((acpi_physical_address) 244 address, ACPI_LODWORD(value), 245 width); 246 if (ACPI_FAILURE(status)) { 247 return (status); 248 } 249 250 if (reg->bit_width == 64) { 251 status = acpi_os_write_memory((acpi_physical_address) 252 (address + 4), 253 ACPI_HIDWORD(value), 32); 254 if (ACPI_FAILURE(status)) { 255 return (status); 256 } 257 } 258 } else { /* ACPI_ADR_SPACE_SYSTEM_IO, validated earlier */ 259 260 status = acpi_hw_write_port((acpi_io_address) 261 address, ACPI_LODWORD(value), 262 width); 263 if (ACPI_FAILURE(status)) { 264 return (status); 265 } 266 267 if (reg->bit_width == 64) { 268 status = acpi_hw_write_port((acpi_io_address) 269 (address + 4), 270 ACPI_HIDWORD(value), 32); 271 if (ACPI_FAILURE(status)) { 272 return (status); 273 } 274 } 275 } 276 277 ACPI_DEBUG_PRINT((ACPI_DB_IO, 278 "Wrote: %8.8X%8.8X width %2d to %8.8X%8.8X (%s)\n", 279 ACPI_FORMAT_UINT64(value), reg->bit_width, 280 ACPI_FORMAT_UINT64(address), 281 acpi_ut_get_region_name(reg->space_id))); 282 283 return (status); 284 } 285 286 ACPI_EXPORT_SYMBOL(acpi_write) 287 288 /******************************************************************************* 289 * 290 * FUNCTION: acpi_read_bit_register 291 * 292 * PARAMETERS: register_id - ID of ACPI Bit Register to access 293 * return_value - Value that was read from the register, 294 * normalized to bit position zero. 295 * 296 * RETURN: Status and the value read from the specified Register. Value 297 * returned is normalized to bit0 (is shifted all the way right) 298 * 299 * DESCRIPTION: ACPI bit_register read function. Does not acquire the HW lock. 300 * 301 * SUPPORTS: Bit fields in PM1 Status, PM1 Enable, PM1 Control, and 302 * PM2 Control. 303 * 304 * Note: The hardware lock is not required when reading the ACPI bit registers 305 * since almost all of them are single bit and it does not matter that 306 * the parent hardware register can be split across two physical 307 * registers. The only multi-bit field is SLP_TYP in the PM1 control 308 * register, but this field does not cross an 8-bit boundary (nor does 309 * it make much sense to actually read this field.) 310 * 311 ******************************************************************************/ 312 acpi_status acpi_read_bit_register(u32 register_id, u32 *return_value) 313 { 314 struct acpi_bit_register_info *bit_reg_info; 315 u32 register_value; 316 u32 value; 317 acpi_status status; 318 319 ACPI_FUNCTION_TRACE_U32(acpi_read_bit_register, register_id); 320 321 /* Get the info structure corresponding to the requested ACPI Register */ 322 323 bit_reg_info = acpi_hw_get_bit_register_info(register_id); 324 if (!bit_reg_info) { 325 return_ACPI_STATUS(AE_BAD_PARAMETER); 326 } 327 328 /* Read the entire parent register */ 329 330 status = acpi_hw_register_read(bit_reg_info->parent_register, 331 ®ister_value); 332 if (ACPI_FAILURE(status)) { 333 return_ACPI_STATUS(status); 334 } 335 336 /* Normalize the value that was read, mask off other bits */ 337 338 value = ((register_value & bit_reg_info->access_bit_mask) 339 >> bit_reg_info->bit_position); 340 341 ACPI_DEBUG_PRINT((ACPI_DB_IO, 342 "BitReg %X, ParentReg %X, Actual %8.8X, ReturnValue %8.8X\n", 343 register_id, bit_reg_info->parent_register, 344 register_value, value)); 345 346 *return_value = value; 347 return_ACPI_STATUS(AE_OK); 348 } 349 350 ACPI_EXPORT_SYMBOL(acpi_read_bit_register) 351 352 /******************************************************************************* 353 * 354 * FUNCTION: acpi_write_bit_register 355 * 356 * PARAMETERS: register_id - ID of ACPI Bit Register to access 357 * Value - Value to write to the register, in bit 358 * position zero. The bit is automaticallly 359 * shifted to the correct position. 360 * 361 * RETURN: Status 362 * 363 * DESCRIPTION: ACPI Bit Register write function. Acquires the hardware lock 364 * since most operations require a read/modify/write sequence. 365 * 366 * SUPPORTS: Bit fields in PM1 Status, PM1 Enable, PM1 Control, and 367 * PM2 Control. 368 * 369 * Note that at this level, the fact that there may be actually two 370 * hardware registers (A and B - and B may not exist) is abstracted. 371 * 372 ******************************************************************************/ 373 acpi_status acpi_write_bit_register(u32 register_id, u32 value) 374 { 375 struct acpi_bit_register_info *bit_reg_info; 376 acpi_cpu_flags lock_flags; 377 u32 register_value; 378 acpi_status status = AE_OK; 379 380 ACPI_FUNCTION_TRACE_U32(acpi_write_bit_register, register_id); 381 382 /* Get the info structure corresponding to the requested ACPI Register */ 383 384 bit_reg_info = acpi_hw_get_bit_register_info(register_id); 385 if (!bit_reg_info) { 386 return_ACPI_STATUS(AE_BAD_PARAMETER); 387 } 388 389 lock_flags = acpi_os_acquire_lock(acpi_gbl_hardware_lock); 390 391 /* 392 * At this point, we know that the parent register is one of the 393 * following: PM1 Status, PM1 Enable, PM1 Control, or PM2 Control 394 */ 395 if (bit_reg_info->parent_register != ACPI_REGISTER_PM1_STATUS) { 396 /* 397 * 1) Case for PM1 Enable, PM1 Control, and PM2 Control 398 * 399 * Perform a register read to preserve the bits that we are not 400 * interested in 401 */ 402 status = acpi_hw_register_read(bit_reg_info->parent_register, 403 ®ister_value); 404 if (ACPI_FAILURE(status)) { 405 goto unlock_and_exit; 406 } 407 408 /* 409 * Insert the input bit into the value that was just read 410 * and write the register 411 */ 412 ACPI_REGISTER_INSERT_VALUE(register_value, 413 bit_reg_info->bit_position, 414 bit_reg_info->access_bit_mask, 415 value); 416 417 status = acpi_hw_register_write(bit_reg_info->parent_register, 418 register_value); 419 } else { 420 /* 421 * 2) Case for PM1 Status 422 * 423 * The Status register is different from the rest. Clear an event 424 * by writing 1, writing 0 has no effect. So, the only relevant 425 * information is the single bit we're interested in, all others 426 * should be written as 0 so they will be left unchanged. 427 */ 428 register_value = ACPI_REGISTER_PREPARE_BITS(value, 429 bit_reg_info-> 430 bit_position, 431 bit_reg_info-> 432 access_bit_mask); 433 434 /* No need to write the register if value is all zeros */ 435 436 if (register_value) { 437 status = 438 acpi_hw_register_write(ACPI_REGISTER_PM1_STATUS, 439 register_value); 440 } 441 } 442 443 ACPI_DEBUG_PRINT((ACPI_DB_IO, 444 "BitReg %X, ParentReg %X, Value %8.8X, Actual %8.8X\n", 445 register_id, bit_reg_info->parent_register, value, 446 register_value)); 447 448 unlock_and_exit: 449 450 acpi_os_release_lock(acpi_gbl_hardware_lock, lock_flags); 451 return_ACPI_STATUS(status); 452 } 453 454 ACPI_EXPORT_SYMBOL(acpi_write_bit_register) 455 456 /******************************************************************************* 457 * 458 * FUNCTION: acpi_get_sleep_type_data 459 * 460 * PARAMETERS: sleep_state - Numeric sleep state 461 * *sleep_type_a - Where SLP_TYPa is returned 462 * *sleep_type_b - Where SLP_TYPb is returned 463 * 464 * RETURN: Status - ACPI status 465 * 466 * DESCRIPTION: Obtain the SLP_TYPa and SLP_TYPb values for the requested sleep 467 * state. 468 * 469 ******************************************************************************/ 470 acpi_status 471 acpi_get_sleep_type_data(u8 sleep_state, u8 *sleep_type_a, u8 *sleep_type_b) 472 { 473 acpi_status status = AE_OK; 474 struct acpi_evaluate_info *info; 475 476 ACPI_FUNCTION_TRACE(acpi_get_sleep_type_data); 477 478 /* Validate parameters */ 479 480 if ((sleep_state > ACPI_S_STATES_MAX) || !sleep_type_a || !sleep_type_b) { 481 return_ACPI_STATUS(AE_BAD_PARAMETER); 482 } 483 484 /* Allocate the evaluation information block */ 485 486 info = ACPI_ALLOCATE_ZEROED(sizeof(struct acpi_evaluate_info)); 487 if (!info) { 488 return_ACPI_STATUS(AE_NO_MEMORY); 489 } 490 491 info->pathname = 492 ACPI_CAST_PTR(char, acpi_gbl_sleep_state_names[sleep_state]); 493 494 /* Evaluate the namespace object containing the values for this state */ 495 496 status = acpi_ns_evaluate(info); 497 if (ACPI_FAILURE(status)) { 498 ACPI_DEBUG_PRINT((ACPI_DB_EXEC, 499 "%s while evaluating SleepState [%s]\n", 500 acpi_format_exception(status), 501 info->pathname)); 502 503 goto cleanup; 504 } 505 506 /* Must have a return object */ 507 508 if (!info->return_object) { 509 ACPI_ERROR((AE_INFO, "No Sleep State object returned from [%s]", 510 info->pathname)); 511 status = AE_NOT_EXIST; 512 } 513 514 /* It must be of type Package */ 515 516 else if (info->return_object->common.type != ACPI_TYPE_PACKAGE) { 517 ACPI_ERROR((AE_INFO, 518 "Sleep State return object is not a Package")); 519 status = AE_AML_OPERAND_TYPE; 520 } 521 522 /* 523 * The package must have at least two elements. NOTE (March 2005): This 524 * goes against the current ACPI spec which defines this object as a 525 * package with one encoded DWORD element. However, existing practice 526 * by BIOS vendors seems to be to have 2 or more elements, at least 527 * one per sleep type (A/B). 528 */ 529 else if (info->return_object->package.count < 2) { 530 ACPI_ERROR((AE_INFO, 531 "Sleep State return package does not have at least two elements")); 532 status = AE_AML_NO_OPERAND; 533 } 534 535 /* The first two elements must both be of type Integer */ 536 537 else if (((info->return_object->package.elements[0])->common.type 538 != ACPI_TYPE_INTEGER) || 539 ((info->return_object->package.elements[1])->common.type 540 != ACPI_TYPE_INTEGER)) { 541 ACPI_ERROR((AE_INFO, 542 "Sleep State return package elements are not both Integers " 543 "(%s, %s)", 544 acpi_ut_get_object_type_name(info->return_object-> 545 package.elements[0]), 546 acpi_ut_get_object_type_name(info->return_object-> 547 package.elements[1]))); 548 status = AE_AML_OPERAND_TYPE; 549 } else { 550 /* Valid _Sx_ package size, type, and value */ 551 552 *sleep_type_a = (u8) 553 (info->return_object->package.elements[0])->integer.value; 554 *sleep_type_b = (u8) 555 (info->return_object->package.elements[1])->integer.value; 556 } 557 558 if (ACPI_FAILURE(status)) { 559 ACPI_EXCEPTION((AE_INFO, status, 560 "While evaluating SleepState [%s], bad Sleep object %p type %s", 561 info->pathname, info->return_object, 562 acpi_ut_get_object_type_name(info-> 563 return_object))); 564 } 565 566 acpi_ut_remove_reference(info->return_object); 567 568 cleanup: 569 ACPI_FREE(info); 570 return_ACPI_STATUS(status); 571 } 572 573 ACPI_EXPORT_SYMBOL(acpi_get_sleep_type_data) 574