1 /* 2 * Intel MID PCI support 3 * Copyright (c) 2008 Intel Corporation 4 * Jesse Barnes <jesse.barnes@intel.com> 5 * 6 * Moorestown has an interesting PCI implementation: 7 * - configuration space is memory mapped (as defined by MCFG) 8 * - Lincroft devices also have a real, type 1 configuration space 9 * - Early Lincroft silicon has a type 1 access bug that will cause 10 * a hang if non-existent devices are accessed 11 * - some devices have the "fixed BAR" capability, which means 12 * they can't be relocated or modified; check for that during 13 * BAR sizing 14 * 15 * So, we use the MCFG space for all reads and writes, but also send 16 * Lincroft writes to type 1 space. But only read/write if the device 17 * actually exists, otherwise return all 1s for reads and bit bucket 18 * the writes. 19 */ 20 21 #include <linux/sched.h> 22 #include <linux/pci.h> 23 #include <linux/ioport.h> 24 #include <linux/init.h> 25 #include <linux/dmi.h> 26 #include <linux/acpi.h> 27 #include <linux/io.h> 28 #include <linux/smp.h> 29 30 #include <asm/segment.h> 31 #include <asm/pci_x86.h> 32 #include <asm/hw_irq.h> 33 #include <asm/io_apic.h> 34 #include <asm/intel-mid.h> 35 36 #define PCIE_CAP_OFFSET 0x100 37 38 /* Quirks for the listed devices */ 39 #define PCI_DEVICE_ID_INTEL_MRFL_MMC 0x1190 40 41 /* Fixed BAR fields */ 42 #define PCIE_VNDR_CAP_ID_FIXED_BAR 0x00 /* Fixed BAR (TBD) */ 43 #define PCI_FIXED_BAR_0_SIZE 0x04 44 #define PCI_FIXED_BAR_1_SIZE 0x08 45 #define PCI_FIXED_BAR_2_SIZE 0x0c 46 #define PCI_FIXED_BAR_3_SIZE 0x10 47 #define PCI_FIXED_BAR_4_SIZE 0x14 48 #define PCI_FIXED_BAR_5_SIZE 0x1c 49 50 static int pci_soc_mode; 51 52 /** 53 * fixed_bar_cap - return the offset of the fixed BAR cap if found 54 * @bus: PCI bus 55 * @devfn: device in question 56 * 57 * Look for the fixed BAR cap on @bus and @devfn, returning its offset 58 * if found or 0 otherwise. 59 */ 60 static int fixed_bar_cap(struct pci_bus *bus, unsigned int devfn) 61 { 62 int pos; 63 u32 pcie_cap = 0, cap_data; 64 65 pos = PCIE_CAP_OFFSET; 66 67 if (!raw_pci_ext_ops) 68 return 0; 69 70 while (pos) { 71 if (raw_pci_ext_ops->read(pci_domain_nr(bus), bus->number, 72 devfn, pos, 4, &pcie_cap)) 73 return 0; 74 75 if (PCI_EXT_CAP_ID(pcie_cap) == 0x0000 || 76 PCI_EXT_CAP_ID(pcie_cap) == 0xffff) 77 break; 78 79 if (PCI_EXT_CAP_ID(pcie_cap) == PCI_EXT_CAP_ID_VNDR) { 80 raw_pci_ext_ops->read(pci_domain_nr(bus), bus->number, 81 devfn, pos + 4, 4, &cap_data); 82 if ((cap_data & 0xffff) == PCIE_VNDR_CAP_ID_FIXED_BAR) 83 return pos; 84 } 85 86 pos = PCI_EXT_CAP_NEXT(pcie_cap); 87 } 88 89 return 0; 90 } 91 92 static int pci_device_update_fixed(struct pci_bus *bus, unsigned int devfn, 93 int reg, int len, u32 val, int offset) 94 { 95 u32 size; 96 unsigned int domain, busnum; 97 int bar = (reg - PCI_BASE_ADDRESS_0) >> 2; 98 99 domain = pci_domain_nr(bus); 100 busnum = bus->number; 101 102 if (val == ~0 && len == 4) { 103 unsigned long decode; 104 105 raw_pci_ext_ops->read(domain, busnum, devfn, 106 offset + 8 + (bar * 4), 4, &size); 107 108 /* Turn the size into a decode pattern for the sizing code */ 109 if (size) { 110 decode = size - 1; 111 decode |= decode >> 1; 112 decode |= decode >> 2; 113 decode |= decode >> 4; 114 decode |= decode >> 8; 115 decode |= decode >> 16; 116 decode++; 117 decode = ~(decode - 1); 118 } else { 119 decode = 0; 120 } 121 122 /* 123 * If val is all ones, the core code is trying to size the reg, 124 * so update the mmconfig space with the real size. 125 * 126 * Note: this assumes the fixed size we got is a power of two. 127 */ 128 return raw_pci_ext_ops->write(domain, busnum, devfn, reg, 4, 129 decode); 130 } 131 132 /* This is some other kind of BAR write, so just do it. */ 133 return raw_pci_ext_ops->write(domain, busnum, devfn, reg, len, val); 134 } 135 136 /** 137 * type1_access_ok - check whether to use type 1 138 * @bus: bus number 139 * @devfn: device & function in question 140 * 141 * If the bus is on a Lincroft chip and it exists, or is not on a Lincroft at 142 * all, the we can go ahead with any reads & writes. If it's on a Lincroft, 143 * but doesn't exist, avoid the access altogether to keep the chip from 144 * hanging. 145 */ 146 static bool type1_access_ok(unsigned int bus, unsigned int devfn, int reg) 147 { 148 /* 149 * This is a workaround for A0 LNC bug where PCI status register does 150 * not have new CAP bit set. can not be written by SW either. 151 * 152 * PCI header type in real LNC indicates a single function device, this 153 * will prevent probing other devices under the same function in PCI 154 * shim. Therefore, use the header type in shim instead. 155 */ 156 if (reg >= 0x100 || reg == PCI_STATUS || reg == PCI_HEADER_TYPE) 157 return false; 158 if (bus == 0 && (devfn == PCI_DEVFN(2, 0) 159 || devfn == PCI_DEVFN(0, 0) 160 || devfn == PCI_DEVFN(3, 0))) 161 return true; 162 return false; /* Langwell on others */ 163 } 164 165 static int pci_read(struct pci_bus *bus, unsigned int devfn, int where, 166 int size, u32 *value) 167 { 168 if (type1_access_ok(bus->number, devfn, where)) 169 return pci_direct_conf1.read(pci_domain_nr(bus), bus->number, 170 devfn, where, size, value); 171 return raw_pci_ext_ops->read(pci_domain_nr(bus), bus->number, 172 devfn, where, size, value); 173 } 174 175 static int pci_write(struct pci_bus *bus, unsigned int devfn, int where, 176 int size, u32 value) 177 { 178 int offset; 179 180 /* 181 * On MRST, there is no PCI ROM BAR, this will cause a subsequent read 182 * to ROM BAR return 0 then being ignored. 183 */ 184 if (where == PCI_ROM_ADDRESS) 185 return 0; 186 187 /* 188 * Devices with fixed BARs need special handling: 189 * - BAR sizing code will save, write ~0, read size, restore 190 * - so writes to fixed BARs need special handling 191 * - other writes to fixed BAR devices should go through mmconfig 192 */ 193 offset = fixed_bar_cap(bus, devfn); 194 if (offset && 195 (where >= PCI_BASE_ADDRESS_0 && where <= PCI_BASE_ADDRESS_5)) { 196 return pci_device_update_fixed(bus, devfn, where, size, value, 197 offset); 198 } 199 200 /* 201 * On Moorestown update both real & mmconfig space 202 * Note: early Lincroft silicon can't handle type 1 accesses to 203 * non-existent devices, so just eat the write in that case. 204 */ 205 if (type1_access_ok(bus->number, devfn, where)) 206 return pci_direct_conf1.write(pci_domain_nr(bus), bus->number, 207 devfn, where, size, value); 208 return raw_pci_ext_ops->write(pci_domain_nr(bus), bus->number, devfn, 209 where, size, value); 210 } 211 212 static int intel_mid_pci_irq_enable(struct pci_dev *dev) 213 { 214 struct irq_alloc_info info; 215 int polarity; 216 int ret; 217 218 if (pci_has_managed_irq(dev)) 219 return 0; 220 221 switch (intel_mid_identify_cpu()) { 222 case INTEL_MID_CPU_CHIP_TANGIER: 223 polarity = IOAPIC_POL_HIGH; 224 225 /* Special treatment for IRQ0 */ 226 if (dev->irq == 0) { 227 /* 228 * TNG has IRQ0 assigned to eMMC controller. But there 229 * are also other devices with bogus PCI configuration 230 * that have IRQ0 assigned. This check ensures that 231 * eMMC gets it. 232 */ 233 if (dev->device != PCI_DEVICE_ID_INTEL_MRFL_MMC) 234 return -EBUSY; 235 } 236 break; 237 default: 238 polarity = IOAPIC_POL_LOW; 239 break; 240 } 241 242 ioapic_set_alloc_attr(&info, dev_to_node(&dev->dev), 1, polarity); 243 244 /* 245 * MRST only have IOAPIC, the PCI irq lines are 1:1 mapped to 246 * IOAPIC RTE entries, so we just enable RTE for the device. 247 */ 248 ret = mp_map_gsi_to_irq(dev->irq, IOAPIC_MAP_ALLOC, &info); 249 if (ret < 0) 250 return ret; 251 252 dev->irq_managed = 1; 253 254 return 0; 255 } 256 257 static void intel_mid_pci_irq_disable(struct pci_dev *dev) 258 { 259 if (pci_has_managed_irq(dev)) { 260 mp_unmap_irq(dev->irq); 261 dev->irq_managed = 0; 262 /* 263 * Don't reset dev->irq here, otherwise 264 * intel_mid_pci_irq_enable() will fail on next call. 265 */ 266 } 267 } 268 269 static struct pci_ops intel_mid_pci_ops = { 270 .read = pci_read, 271 .write = pci_write, 272 }; 273 274 /** 275 * intel_mid_pci_init - installs intel_mid_pci_ops 276 * 277 * Moorestown has an interesting PCI implementation (see above). 278 * Called when the early platform detection installs it. 279 */ 280 int __init intel_mid_pci_init(void) 281 { 282 pr_info("Intel MID platform detected, using MID PCI ops\n"); 283 pci_mmcfg_late_init(); 284 pcibios_enable_irq = intel_mid_pci_irq_enable; 285 pcibios_disable_irq = intel_mid_pci_irq_disable; 286 pci_root_ops = intel_mid_pci_ops; 287 pci_soc_mode = 1; 288 /* Continue with standard init */ 289 return 1; 290 } 291 292 /* 293 * Langwell devices are not true PCI devices; they are not subject to 10 ms 294 * d3 to d0 delay required by PCI spec. 295 */ 296 static void pci_d3delay_fixup(struct pci_dev *dev) 297 { 298 /* 299 * PCI fixups are effectively decided compile time. If we have a dual 300 * SoC/non-SoC kernel we don't want to mangle d3 on non-SoC devices. 301 */ 302 if (!pci_soc_mode) 303 return; 304 /* 305 * True PCI devices in Lincroft should allow type 1 access, the rest 306 * are Langwell fake PCI devices. 307 */ 308 if (type1_access_ok(dev->bus->number, dev->devfn, PCI_DEVICE_ID)) 309 return; 310 dev->d3_delay = 0; 311 } 312 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_ANY_ID, pci_d3delay_fixup); 313 314 static void mrst_power_off_unused_dev(struct pci_dev *dev) 315 { 316 pci_set_power_state(dev, PCI_D3hot); 317 } 318 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x0801, mrst_power_off_unused_dev); 319 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x0809, mrst_power_off_unused_dev); 320 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x080C, mrst_power_off_unused_dev); 321 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x0815, mrst_power_off_unused_dev); 322 323 /* 324 * Langwell devices reside at fixed offsets, don't try to move them. 325 */ 326 static void pci_fixed_bar_fixup(struct pci_dev *dev) 327 { 328 unsigned long offset; 329 u32 size; 330 int i; 331 332 if (!pci_soc_mode) 333 return; 334 335 /* Must have extended configuration space */ 336 if (dev->cfg_size < PCIE_CAP_OFFSET + 4) 337 return; 338 339 /* Fixup the BAR sizes for fixed BAR devices and make them unmoveable */ 340 offset = fixed_bar_cap(dev->bus, dev->devfn); 341 if (!offset || PCI_DEVFN(2, 0) == dev->devfn || 342 PCI_DEVFN(2, 2) == dev->devfn) 343 return; 344 345 for (i = 0; i < PCI_ROM_RESOURCE; i++) { 346 pci_read_config_dword(dev, offset + 8 + (i * 4), &size); 347 dev->resource[i].end = dev->resource[i].start + size - 1; 348 dev->resource[i].flags |= IORESOURCE_PCI_FIXED; 349 } 350 } 351 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_ANY_ID, pci_fixed_bar_fixup); 352