1 // SPDX-License-Identifier: GPL-2.0 2 /* 3 * Intel MID PCI support 4 * Copyright (c) 2008 Intel Corporation 5 * Jesse Barnes <jesse.barnes@intel.com> 6 * 7 * Moorestown has an interesting PCI implementation: 8 * - configuration space is memory mapped (as defined by MCFG) 9 * - Lincroft devices also have a real, type 1 configuration space 10 * - Early Lincroft silicon has a type 1 access bug that will cause 11 * a hang if non-existent devices are accessed 12 * - some devices have the "fixed BAR" capability, which means 13 * they can't be relocated or modified; check for that during 14 * BAR sizing 15 * 16 * So, we use the MCFG space for all reads and writes, but also send 17 * Lincroft writes to type 1 space. But only read/write if the device 18 * actually exists, otherwise return all 1s for reads and bit bucket 19 * the writes. 20 */ 21 22 #include <linux/sched.h> 23 #include <linux/pci.h> 24 #include <linux/ioport.h> 25 #include <linux/init.h> 26 #include <linux/dmi.h> 27 #include <linux/acpi.h> 28 #include <linux/io.h> 29 #include <linux/smp.h> 30 31 #include <asm/segment.h> 32 #include <asm/pci_x86.h> 33 #include <asm/hw_irq.h> 34 #include <asm/io_apic.h> 35 #include <asm/intel-mid.h> 36 37 #define PCIE_CAP_OFFSET 0x100 38 39 /* Quirks for the listed devices */ 40 #define PCI_DEVICE_ID_INTEL_MRFLD_MMC 0x1190 41 #define PCI_DEVICE_ID_INTEL_MRFLD_HSU 0x1191 42 43 /* Fixed BAR fields */ 44 #define PCIE_VNDR_CAP_ID_FIXED_BAR 0x00 /* Fixed BAR (TBD) */ 45 #define PCI_FIXED_BAR_0_SIZE 0x04 46 #define PCI_FIXED_BAR_1_SIZE 0x08 47 #define PCI_FIXED_BAR_2_SIZE 0x0c 48 #define PCI_FIXED_BAR_3_SIZE 0x10 49 #define PCI_FIXED_BAR_4_SIZE 0x14 50 #define PCI_FIXED_BAR_5_SIZE 0x1c 51 52 static int pci_soc_mode; 53 54 /** 55 * fixed_bar_cap - return the offset of the fixed BAR cap if found 56 * @bus: PCI bus 57 * @devfn: device in question 58 * 59 * Look for the fixed BAR cap on @bus and @devfn, returning its offset 60 * if found or 0 otherwise. 61 */ 62 static int fixed_bar_cap(struct pci_bus *bus, unsigned int devfn) 63 { 64 int pos; 65 u32 pcie_cap = 0, cap_data; 66 67 pos = PCIE_CAP_OFFSET; 68 69 if (!raw_pci_ext_ops) 70 return 0; 71 72 while (pos) { 73 if (raw_pci_ext_ops->read(pci_domain_nr(bus), bus->number, 74 devfn, pos, 4, &pcie_cap)) 75 return 0; 76 77 if (PCI_EXT_CAP_ID(pcie_cap) == 0x0000 || 78 PCI_EXT_CAP_ID(pcie_cap) == 0xffff) 79 break; 80 81 if (PCI_EXT_CAP_ID(pcie_cap) == PCI_EXT_CAP_ID_VNDR) { 82 raw_pci_ext_ops->read(pci_domain_nr(bus), bus->number, 83 devfn, pos + 4, 4, &cap_data); 84 if ((cap_data & 0xffff) == PCIE_VNDR_CAP_ID_FIXED_BAR) 85 return pos; 86 } 87 88 pos = PCI_EXT_CAP_NEXT(pcie_cap); 89 } 90 91 return 0; 92 } 93 94 static int pci_device_update_fixed(struct pci_bus *bus, unsigned int devfn, 95 int reg, int len, u32 val, int offset) 96 { 97 u32 size; 98 unsigned int domain, busnum; 99 int bar = (reg - PCI_BASE_ADDRESS_0) >> 2; 100 101 domain = pci_domain_nr(bus); 102 busnum = bus->number; 103 104 if (val == ~0 && len == 4) { 105 unsigned long decode; 106 107 raw_pci_ext_ops->read(domain, busnum, devfn, 108 offset + 8 + (bar * 4), 4, &size); 109 110 /* Turn the size into a decode pattern for the sizing code */ 111 if (size) { 112 decode = size - 1; 113 decode |= decode >> 1; 114 decode |= decode >> 2; 115 decode |= decode >> 4; 116 decode |= decode >> 8; 117 decode |= decode >> 16; 118 decode++; 119 decode = ~(decode - 1); 120 } else { 121 decode = 0; 122 } 123 124 /* 125 * If val is all ones, the core code is trying to size the reg, 126 * so update the mmconfig space with the real size. 127 * 128 * Note: this assumes the fixed size we got is a power of two. 129 */ 130 return raw_pci_ext_ops->write(domain, busnum, devfn, reg, 4, 131 decode); 132 } 133 134 /* This is some other kind of BAR write, so just do it. */ 135 return raw_pci_ext_ops->write(domain, busnum, devfn, reg, len, val); 136 } 137 138 /** 139 * type1_access_ok - check whether to use type 1 140 * @bus: bus number 141 * @devfn: device & function in question 142 * 143 * If the bus is on a Lincroft chip and it exists, or is not on a Lincroft at 144 * all, the we can go ahead with any reads & writes. If it's on a Lincroft, 145 * but doesn't exist, avoid the access altogether to keep the chip from 146 * hanging. 147 */ 148 static bool type1_access_ok(unsigned int bus, unsigned int devfn, int reg) 149 { 150 /* 151 * This is a workaround for A0 LNC bug where PCI status register does 152 * not have new CAP bit set. can not be written by SW either. 153 * 154 * PCI header type in real LNC indicates a single function device, this 155 * will prevent probing other devices under the same function in PCI 156 * shim. Therefore, use the header type in shim instead. 157 */ 158 if (reg >= 0x100 || reg == PCI_STATUS || reg == PCI_HEADER_TYPE) 159 return false; 160 if (bus == 0 && (devfn == PCI_DEVFN(2, 0) 161 || devfn == PCI_DEVFN(0, 0) 162 || devfn == PCI_DEVFN(3, 0))) 163 return true; 164 return false; /* Langwell on others */ 165 } 166 167 static int pci_read(struct pci_bus *bus, unsigned int devfn, int where, 168 int size, u32 *value) 169 { 170 if (type1_access_ok(bus->number, devfn, where)) 171 return pci_direct_conf1.read(pci_domain_nr(bus), bus->number, 172 devfn, where, size, value); 173 return raw_pci_ext_ops->read(pci_domain_nr(bus), bus->number, 174 devfn, where, size, value); 175 } 176 177 static int pci_write(struct pci_bus *bus, unsigned int devfn, int where, 178 int size, u32 value) 179 { 180 int offset; 181 182 /* 183 * On MRST, there is no PCI ROM BAR, this will cause a subsequent read 184 * to ROM BAR return 0 then being ignored. 185 */ 186 if (where == PCI_ROM_ADDRESS) 187 return 0; 188 189 /* 190 * Devices with fixed BARs need special handling: 191 * - BAR sizing code will save, write ~0, read size, restore 192 * - so writes to fixed BARs need special handling 193 * - other writes to fixed BAR devices should go through mmconfig 194 */ 195 offset = fixed_bar_cap(bus, devfn); 196 if (offset && 197 (where >= PCI_BASE_ADDRESS_0 && where <= PCI_BASE_ADDRESS_5)) { 198 return pci_device_update_fixed(bus, devfn, where, size, value, 199 offset); 200 } 201 202 /* 203 * On Moorestown update both real & mmconfig space 204 * Note: early Lincroft silicon can't handle type 1 accesses to 205 * non-existent devices, so just eat the write in that case. 206 */ 207 if (type1_access_ok(bus->number, devfn, where)) 208 return pci_direct_conf1.write(pci_domain_nr(bus), bus->number, 209 devfn, where, size, value); 210 return raw_pci_ext_ops->write(pci_domain_nr(bus), bus->number, devfn, 211 where, size, value); 212 } 213 214 static int intel_mid_pci_irq_enable(struct pci_dev *dev) 215 { 216 struct irq_alloc_info info; 217 int polarity; 218 int ret; 219 u8 gsi; 220 221 if (dev->irq_managed && dev->irq > 0) 222 return 0; 223 224 ret = pci_read_config_byte(dev, PCI_INTERRUPT_LINE, &gsi); 225 if (ret < 0) { 226 dev_warn(&dev->dev, "Failed to read interrupt line: %d\n", ret); 227 return ret; 228 } 229 230 switch (intel_mid_identify_cpu()) { 231 case INTEL_MID_CPU_CHIP_TANGIER: 232 polarity = IOAPIC_POL_HIGH; 233 234 /* Special treatment for IRQ0 */ 235 if (gsi == 0) { 236 /* 237 * Skip HS UART common registers device since it has 238 * IRQ0 assigned and not used by the kernel. 239 */ 240 if (dev->device == PCI_DEVICE_ID_INTEL_MRFLD_HSU) 241 return -EBUSY; 242 /* 243 * TNG has IRQ0 assigned to eMMC controller. But there 244 * are also other devices with bogus PCI configuration 245 * that have IRQ0 assigned. This check ensures that 246 * eMMC gets it. The rest of devices still could be 247 * enabled without interrupt line being allocated. 248 */ 249 if (dev->device != PCI_DEVICE_ID_INTEL_MRFLD_MMC) 250 return 0; 251 } 252 break; 253 default: 254 polarity = IOAPIC_POL_LOW; 255 break; 256 } 257 258 ioapic_set_alloc_attr(&info, dev_to_node(&dev->dev), 1, polarity); 259 260 /* 261 * MRST only have IOAPIC, the PCI irq lines are 1:1 mapped to 262 * IOAPIC RTE entries, so we just enable RTE for the device. 263 */ 264 ret = mp_map_gsi_to_irq(gsi, IOAPIC_MAP_ALLOC, &info); 265 if (ret < 0) 266 return ret; 267 268 dev->irq = ret; 269 dev->irq_managed = 1; 270 271 return 0; 272 } 273 274 static void intel_mid_pci_irq_disable(struct pci_dev *dev) 275 { 276 if (!mp_should_keep_irq(&dev->dev) && dev->irq_managed && 277 dev->irq > 0) { 278 mp_unmap_irq(dev->irq); 279 dev->irq_managed = 0; 280 } 281 } 282 283 static const struct pci_ops intel_mid_pci_ops __initconst = { 284 .read = pci_read, 285 .write = pci_write, 286 }; 287 288 /** 289 * intel_mid_pci_init - installs intel_mid_pci_ops 290 * 291 * Moorestown has an interesting PCI implementation (see above). 292 * Called when the early platform detection installs it. 293 */ 294 int __init intel_mid_pci_init(void) 295 { 296 pr_info("Intel MID platform detected, using MID PCI ops\n"); 297 pci_mmcfg_late_init(); 298 pcibios_enable_irq = intel_mid_pci_irq_enable; 299 pcibios_disable_irq = intel_mid_pci_irq_disable; 300 pci_root_ops = intel_mid_pci_ops; 301 pci_soc_mode = 1; 302 /* Continue with standard init */ 303 acpi_noirq_set(); 304 return 1; 305 } 306 307 /* 308 * Langwell devices are not true PCI devices; they are not subject to 10 ms 309 * d3 to d0 delay required by PCI spec. 310 */ 311 static void pci_d3delay_fixup(struct pci_dev *dev) 312 { 313 /* 314 * PCI fixups are effectively decided compile time. If we have a dual 315 * SoC/non-SoC kernel we don't want to mangle d3 on non-SoC devices. 316 */ 317 if (!pci_soc_mode) 318 return; 319 /* 320 * True PCI devices in Lincroft should allow type 1 access, the rest 321 * are Langwell fake PCI devices. 322 */ 323 if (type1_access_ok(dev->bus->number, dev->devfn, PCI_DEVICE_ID)) 324 return; 325 dev->d3_delay = 0; 326 } 327 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_ANY_ID, pci_d3delay_fixup); 328 329 static void mid_power_off_one_device(struct pci_dev *dev) 330 { 331 u16 pmcsr; 332 333 /* 334 * Update current state first, otherwise PCI core enforces PCI_D0 in 335 * pci_set_power_state() for devices which status was PCI_UNKNOWN. 336 */ 337 pci_read_config_word(dev, dev->pm_cap + PCI_PM_CTRL, &pmcsr); 338 dev->current_state = (pci_power_t __force)(pmcsr & PCI_PM_CTRL_STATE_MASK); 339 340 pci_set_power_state(dev, PCI_D3hot); 341 } 342 343 static void mid_power_off_devices(struct pci_dev *dev) 344 { 345 int id; 346 347 if (!pci_soc_mode) 348 return; 349 350 id = intel_mid_pwr_get_lss_id(dev); 351 if (id < 0) 352 return; 353 354 /* 355 * This sets only PMCSR bits. The actual power off will happen in 356 * arch/x86/platform/intel-mid/pwr.c. 357 */ 358 mid_power_off_one_device(dev); 359 } 360 361 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_ANY_ID, mid_power_off_devices); 362 363 /* 364 * Langwell devices reside at fixed offsets, don't try to move them. 365 */ 366 static void pci_fixed_bar_fixup(struct pci_dev *dev) 367 { 368 unsigned long offset; 369 u32 size; 370 int i; 371 372 if (!pci_soc_mode) 373 return; 374 375 /* Must have extended configuration space */ 376 if (dev->cfg_size < PCIE_CAP_OFFSET + 4) 377 return; 378 379 /* Fixup the BAR sizes for fixed BAR devices and make them unmoveable */ 380 offset = fixed_bar_cap(dev->bus, dev->devfn); 381 if (!offset || PCI_DEVFN(2, 0) == dev->devfn || 382 PCI_DEVFN(2, 2) == dev->devfn) 383 return; 384 385 for (i = 0; i < PCI_STD_NUM_BARS; i++) { 386 pci_read_config_dword(dev, offset + 8 + (i * 4), &size); 387 dev->resource[i].end = dev->resource[i].start + size - 1; 388 dev->resource[i].flags |= IORESOURCE_PCI_FIXED; 389 } 390 } 391 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_ANY_ID, pci_fixed_bar_fixup); 392