1 /* 2 * Exceptions for specific devices. Usually work-arounds for fatal design flaws. 3 */ 4 5 #include <linux/delay.h> 6 #include <linux/dmi.h> 7 #include <linux/pci.h> 8 #include <linux/vgaarb.h> 9 #include <asm/hpet.h> 10 #include <asm/pci_x86.h> 11 12 static void pci_fixup_i450nx(struct pci_dev *d) 13 { 14 /* 15 * i450NX -- Find and scan all secondary buses on all PXB's. 16 */ 17 int pxb, reg; 18 u8 busno, suba, subb; 19 20 dev_warn(&d->dev, "Searching for i450NX host bridges\n"); 21 reg = 0xd0; 22 for(pxb = 0; pxb < 2; pxb++) { 23 pci_read_config_byte(d, reg++, &busno); 24 pci_read_config_byte(d, reg++, &suba); 25 pci_read_config_byte(d, reg++, &subb); 26 dev_dbg(&d->dev, "i450NX PXB %d: %02x/%02x/%02x\n", pxb, busno, 27 suba, subb); 28 if (busno) 29 pcibios_scan_root(busno); /* Bus A */ 30 if (suba < subb) 31 pcibios_scan_root(suba+1); /* Bus B */ 32 } 33 pcibios_last_bus = -1; 34 } 35 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82451NX, pci_fixup_i450nx); 36 37 static void pci_fixup_i450gx(struct pci_dev *d) 38 { 39 /* 40 * i450GX and i450KX -- Find and scan all secondary buses. 41 * (called separately for each PCI bridge found) 42 */ 43 u8 busno; 44 pci_read_config_byte(d, 0x4a, &busno); 45 dev_info(&d->dev, "i440KX/GX host bridge; secondary bus %02x\n", busno); 46 pcibios_scan_root(busno); 47 pcibios_last_bus = -1; 48 } 49 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82454GX, pci_fixup_i450gx); 50 51 static void pci_fixup_umc_ide(struct pci_dev *d) 52 { 53 /* 54 * UM8886BF IDE controller sets region type bits incorrectly, 55 * therefore they look like memory despite of them being I/O. 56 */ 57 int i; 58 59 dev_warn(&d->dev, "Fixing base address flags\n"); 60 for(i = 0; i < 4; i++) 61 d->resource[i].flags |= PCI_BASE_ADDRESS_SPACE_IO; 62 } 63 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_UMC, PCI_DEVICE_ID_UMC_UM8886BF, pci_fixup_umc_ide); 64 65 static void pci_fixup_latency(struct pci_dev *d) 66 { 67 /* 68 * SiS 5597 and 5598 chipsets require latency timer set to 69 * at most 32 to avoid lockups. 70 */ 71 dev_dbg(&d->dev, "Setting max latency to 32\n"); 72 pcibios_max_latency = 32; 73 } 74 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_SI, PCI_DEVICE_ID_SI_5597, pci_fixup_latency); 75 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_SI, PCI_DEVICE_ID_SI_5598, pci_fixup_latency); 76 77 static void pci_fixup_piix4_acpi(struct pci_dev *d) 78 { 79 /* 80 * PIIX4 ACPI device: hardwired IRQ9 81 */ 82 d->irq = 9; 83 } 84 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82371AB_3, pci_fixup_piix4_acpi); 85 86 /* 87 * Addresses issues with problems in the memory write queue timer in 88 * certain VIA Northbridges. This bugfix is per VIA's specifications, 89 * except for the KL133/KM133: clearing bit 5 on those Northbridges seems 90 * to trigger a bug in its integrated ProSavage video card, which 91 * causes screen corruption. We only clear bits 6 and 7 for that chipset, 92 * until VIA can provide us with definitive information on why screen 93 * corruption occurs, and what exactly those bits do. 94 * 95 * VIA 8363,8622,8361 Northbridges: 96 * - bits 5, 6, 7 at offset 0x55 need to be turned off 97 * VIA 8367 (KT266x) Northbridges: 98 * - bits 5, 6, 7 at offset 0x95 need to be turned off 99 * VIA 8363 rev 0x81/0x84 (KL133/KM133) Northbridges: 100 * - bits 6, 7 at offset 0x55 need to be turned off 101 */ 102 103 #define VIA_8363_KL133_REVISION_ID 0x81 104 #define VIA_8363_KM133_REVISION_ID 0x84 105 106 static void pci_fixup_via_northbridge_bug(struct pci_dev *d) 107 { 108 u8 v; 109 int where = 0x55; 110 int mask = 0x1f; /* clear bits 5, 6, 7 by default */ 111 112 if (d->device == PCI_DEVICE_ID_VIA_8367_0) { 113 /* fix pci bus latency issues resulted by NB bios error 114 it appears on bug free^Wreduced kt266x's bios forces 115 NB latency to zero */ 116 pci_write_config_byte(d, PCI_LATENCY_TIMER, 0); 117 118 where = 0x95; /* the memory write queue timer register is 119 different for the KT266x's: 0x95 not 0x55 */ 120 } else if (d->device == PCI_DEVICE_ID_VIA_8363_0 && 121 (d->revision == VIA_8363_KL133_REVISION_ID || 122 d->revision == VIA_8363_KM133_REVISION_ID)) { 123 mask = 0x3f; /* clear only bits 6 and 7; clearing bit 5 124 causes screen corruption on the KL133/KM133 */ 125 } 126 127 pci_read_config_byte(d, where, &v); 128 if (v & ~mask) { 129 dev_warn(&d->dev, "Disabling VIA memory write queue (PCI ID %04x, rev %02x): [%02x] %02x & %02x -> %02x\n", \ 130 d->device, d->revision, where, v, mask, v & mask); 131 v &= mask; 132 pci_write_config_byte(d, where, v); 133 } 134 } 135 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8363_0, pci_fixup_via_northbridge_bug); 136 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8622, pci_fixup_via_northbridge_bug); 137 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8361, pci_fixup_via_northbridge_bug); 138 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8367_0, pci_fixup_via_northbridge_bug); 139 DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8363_0, pci_fixup_via_northbridge_bug); 140 DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8622, pci_fixup_via_northbridge_bug); 141 DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8361, pci_fixup_via_northbridge_bug); 142 DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8367_0, pci_fixup_via_northbridge_bug); 143 144 /* 145 * For some reasons Intel decided that certain parts of their 146 * 815, 845 and some other chipsets must look like PCI-to-PCI bridges 147 * while they are obviously not. The 82801 family (AA, AB, BAM/CAM, 148 * BA/CA/DB and E) PCI bridges are actually HUB-to-PCI ones, according 149 * to Intel terminology. These devices do forward all addresses from 150 * system to PCI bus no matter what are their window settings, so they are 151 * "transparent" (or subtractive decoding) from programmers point of view. 152 */ 153 static void pci_fixup_transparent_bridge(struct pci_dev *dev) 154 { 155 if ((dev->device & 0xff00) == 0x2400) 156 dev->transparent = 1; 157 } 158 DECLARE_PCI_FIXUP_CLASS_HEADER(PCI_VENDOR_ID_INTEL, PCI_ANY_ID, 159 PCI_CLASS_BRIDGE_PCI, 8, pci_fixup_transparent_bridge); 160 161 /* 162 * Fixup for C1 Halt Disconnect problem on nForce2 systems. 163 * 164 * From information provided by "Allen Martin" <AMartin@nvidia.com>: 165 * 166 * A hang is caused when the CPU generates a very fast CONNECT/HALT cycle 167 * sequence. Workaround is to set the SYSTEM_IDLE_TIMEOUT to 80 ns. 168 * This allows the state-machine and timer to return to a proper state within 169 * 80 ns of the CONNECT and probe appearing together. Since the CPU will not 170 * issue another HALT within 80 ns of the initial HALT, the failure condition 171 * is avoided. 172 */ 173 static void pci_fixup_nforce2(struct pci_dev *dev) 174 { 175 u32 val; 176 177 /* 178 * Chip Old value New value 179 * C17 0x1F0FFF01 0x1F01FF01 180 * C18D 0x9F0FFF01 0x9F01FF01 181 * 182 * Northbridge chip version may be determined by 183 * reading the PCI revision ID (0xC1 or greater is C18D). 184 */ 185 pci_read_config_dword(dev, 0x6c, &val); 186 187 /* 188 * Apply fixup if needed, but don't touch disconnect state 189 */ 190 if ((val & 0x00FF0000) != 0x00010000) { 191 dev_warn(&dev->dev, "nForce2 C1 Halt Disconnect fixup\n"); 192 pci_write_config_dword(dev, 0x6c, (val & 0xFF00FFFF) | 0x00010000); 193 } 194 } 195 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE2, pci_fixup_nforce2); 196 DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE2, pci_fixup_nforce2); 197 198 /* Max PCI Express root ports */ 199 #define MAX_PCIEROOT 6 200 static int quirk_aspm_offset[MAX_PCIEROOT << 3]; 201 202 #define GET_INDEX(a, b) ((((a) - PCI_DEVICE_ID_INTEL_MCH_PA) << 3) + ((b) & 7)) 203 204 static int quirk_pcie_aspm_read(struct pci_bus *bus, unsigned int devfn, int where, int size, u32 *value) 205 { 206 return raw_pci_read(pci_domain_nr(bus), bus->number, 207 devfn, where, size, value); 208 } 209 210 /* 211 * Replace the original pci bus ops for write with a new one that will filter 212 * the request to insure ASPM cannot be enabled. 213 */ 214 static int quirk_pcie_aspm_write(struct pci_bus *bus, unsigned int devfn, int where, int size, u32 value) 215 { 216 u8 offset; 217 218 offset = quirk_aspm_offset[GET_INDEX(bus->self->device, devfn)]; 219 220 if ((offset) && (where == offset)) 221 value = value & ~PCI_EXP_LNKCTL_ASPMC; 222 223 return raw_pci_write(pci_domain_nr(bus), bus->number, 224 devfn, where, size, value); 225 } 226 227 static struct pci_ops quirk_pcie_aspm_ops = { 228 .read = quirk_pcie_aspm_read, 229 .write = quirk_pcie_aspm_write, 230 }; 231 232 /* 233 * Prevents PCI Express ASPM (Active State Power Management) being enabled. 234 * 235 * Save the register offset, where the ASPM control bits are located, 236 * for each PCI Express device that is in the device list of 237 * the root port in an array for fast indexing. Replace the bus ops 238 * with the modified one. 239 */ 240 static void pcie_rootport_aspm_quirk(struct pci_dev *pdev) 241 { 242 int i; 243 struct pci_bus *pbus; 244 struct pci_dev *dev; 245 246 if ((pbus = pdev->subordinate) == NULL) 247 return; 248 249 /* 250 * Check if the DID of pdev matches one of the six root ports. This 251 * check is needed in the case this function is called directly by the 252 * hot-plug driver. 253 */ 254 if ((pdev->device < PCI_DEVICE_ID_INTEL_MCH_PA) || 255 (pdev->device > PCI_DEVICE_ID_INTEL_MCH_PC1)) 256 return; 257 258 if (list_empty(&pbus->devices)) { 259 /* 260 * If no device is attached to the root port at power-up or 261 * after hot-remove, the pbus->devices is empty and this code 262 * will set the offsets to zero and the bus ops to parent's bus 263 * ops, which is unmodified. 264 */ 265 for (i = GET_INDEX(pdev->device, 0); i <= GET_INDEX(pdev->device, 7); ++i) 266 quirk_aspm_offset[i] = 0; 267 268 pci_bus_set_ops(pbus, pbus->parent->ops); 269 } else { 270 /* 271 * If devices are attached to the root port at power-up or 272 * after hot-add, the code loops through the device list of 273 * each root port to save the register offsets and replace the 274 * bus ops. 275 */ 276 list_for_each_entry(dev, &pbus->devices, bus_list) 277 /* There are 0 to 8 devices attached to this bus */ 278 quirk_aspm_offset[GET_INDEX(pdev->device, dev->devfn)] = 279 dev->pcie_cap + PCI_EXP_LNKCTL; 280 281 pci_bus_set_ops(pbus, &quirk_pcie_aspm_ops); 282 dev_info(&pbus->dev, "writes to ASPM control bits will be ignored\n"); 283 } 284 285 } 286 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_MCH_PA, pcie_rootport_aspm_quirk); 287 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_MCH_PA1, pcie_rootport_aspm_quirk); 288 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_MCH_PB, pcie_rootport_aspm_quirk); 289 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_MCH_PB1, pcie_rootport_aspm_quirk); 290 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_MCH_PC, pcie_rootport_aspm_quirk); 291 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_MCH_PC1, pcie_rootport_aspm_quirk); 292 293 /* 294 * Fixup to mark boot BIOS video selected by BIOS before it changes 295 * 296 * From information provided by "Jon Smirl" <jonsmirl@gmail.com> 297 * 298 * The standard boot ROM sequence for an x86 machine uses the BIOS 299 * to select an initial video card for boot display. This boot video 300 * card will have its BIOS copied to 0xC0000 in system RAM. 301 * IORESOURCE_ROM_SHADOW is used to associate the boot video 302 * card with this copy. On laptops this copy has to be used since 303 * the main ROM may be compressed or combined with another image. 304 * See pci_map_rom() for use of this flag. Before marking the device 305 * with IORESOURCE_ROM_SHADOW check if a vga_default_device is already set 306 * by either arch code or vga-arbitration; if so only apply the fixup to this 307 * already-determined primary video card. 308 */ 309 310 static void pci_fixup_video(struct pci_dev *pdev) 311 { 312 struct pci_dev *bridge; 313 struct pci_bus *bus; 314 u16 config; 315 struct resource *res; 316 317 /* Is VGA routed to us? */ 318 bus = pdev->bus; 319 while (bus) { 320 bridge = bus->self; 321 322 /* 323 * From information provided by 324 * "David Miller" <davem@davemloft.net> 325 * The bridge control register is valid for PCI header 326 * type BRIDGE, or CARDBUS. Host to PCI controllers use 327 * PCI header type NORMAL. 328 */ 329 if (bridge && (pci_is_bridge(bridge))) { 330 pci_read_config_word(bridge, PCI_BRIDGE_CONTROL, 331 &config); 332 if (!(config & PCI_BRIDGE_CTL_VGA)) 333 return; 334 } 335 bus = bus->parent; 336 } 337 if (!vga_default_device() || pdev == vga_default_device()) { 338 pci_read_config_word(pdev, PCI_COMMAND, &config); 339 if (config & (PCI_COMMAND_IO | PCI_COMMAND_MEMORY)) { 340 res = &pdev->resource[PCI_ROM_RESOURCE]; 341 342 pci_disable_rom(pdev); 343 if (res->parent) 344 release_resource(res); 345 346 res->start = 0xC0000; 347 res->end = res->start + 0x20000 - 1; 348 res->flags = IORESOURCE_MEM | IORESOURCE_ROM_SHADOW | 349 IORESOURCE_PCI_FIXED; 350 dev_info(&pdev->dev, "Video device with shadowed ROM at %pR\n", 351 res); 352 } 353 } 354 } 355 DECLARE_PCI_FIXUP_CLASS_FINAL(PCI_ANY_ID, PCI_ANY_ID, 356 PCI_CLASS_DISPLAY_VGA, 8, pci_fixup_video); 357 358 359 static const struct dmi_system_id msi_k8t_dmi_table[] = { 360 { 361 .ident = "MSI-K8T-Neo2Fir", 362 .matches = { 363 DMI_MATCH(DMI_SYS_VENDOR, "MSI"), 364 DMI_MATCH(DMI_PRODUCT_NAME, "MS-6702E"), 365 }, 366 }, 367 {} 368 }; 369 370 /* 371 * The AMD-Athlon64 board MSI "K8T Neo2-FIR" disables the onboard sound 372 * card if a PCI-soundcard is added. 373 * 374 * The BIOS only gives options "DISABLED" and "AUTO". This code sets 375 * the corresponding register-value to enable the soundcard. 376 * 377 * The soundcard is only enabled, if the mainborad is identified 378 * via DMI-tables and the soundcard is detected to be off. 379 */ 380 static void pci_fixup_msi_k8t_onboard_sound(struct pci_dev *dev) 381 { 382 unsigned char val; 383 if (!dmi_check_system(msi_k8t_dmi_table)) 384 return; /* only applies to MSI K8T Neo2-FIR */ 385 386 pci_read_config_byte(dev, 0x50, &val); 387 if (val & 0x40) { 388 pci_write_config_byte(dev, 0x50, val & (~0x40)); 389 390 /* verify the change for status output */ 391 pci_read_config_byte(dev, 0x50, &val); 392 if (val & 0x40) 393 dev_info(&dev->dev, "Detected MSI K8T Neo2-FIR; " 394 "can't enable onboard soundcard!\n"); 395 else 396 dev_info(&dev->dev, "Detected MSI K8T Neo2-FIR; " 397 "enabled onboard soundcard\n"); 398 } 399 } 400 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8237, 401 pci_fixup_msi_k8t_onboard_sound); 402 DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8237, 403 pci_fixup_msi_k8t_onboard_sound); 404 405 /* 406 * Some Toshiba laptops need extra code to enable their TI TSB43AB22/A. 407 * 408 * We pretend to bring them out of full D3 state, and restore the proper 409 * IRQ, PCI cache line size, and BARs, otherwise the device won't function 410 * properly. In some cases, the device will generate an interrupt on 411 * the wrong IRQ line, causing any devices sharing the line it's 412 * *supposed* to use to be disabled by the kernel's IRQ debug code. 413 */ 414 static u16 toshiba_line_size; 415 416 static const struct dmi_system_id toshiba_ohci1394_dmi_table[] = { 417 { 418 .ident = "Toshiba PS5 based laptop", 419 .matches = { 420 DMI_MATCH(DMI_SYS_VENDOR, "TOSHIBA"), 421 DMI_MATCH(DMI_PRODUCT_VERSION, "PS5"), 422 }, 423 }, 424 { 425 .ident = "Toshiba PSM4 based laptop", 426 .matches = { 427 DMI_MATCH(DMI_SYS_VENDOR, "TOSHIBA"), 428 DMI_MATCH(DMI_PRODUCT_VERSION, "PSM4"), 429 }, 430 }, 431 { 432 .ident = "Toshiba A40 based laptop", 433 .matches = { 434 DMI_MATCH(DMI_SYS_VENDOR, "TOSHIBA"), 435 DMI_MATCH(DMI_PRODUCT_VERSION, "PSA40U"), 436 }, 437 }, 438 { } 439 }; 440 441 static void pci_pre_fixup_toshiba_ohci1394(struct pci_dev *dev) 442 { 443 if (!dmi_check_system(toshiba_ohci1394_dmi_table)) 444 return; /* only applies to certain Toshibas (so far) */ 445 446 dev->current_state = PCI_D3cold; 447 pci_read_config_word(dev, PCI_CACHE_LINE_SIZE, &toshiba_line_size); 448 } 449 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_TI, 0x8032, 450 pci_pre_fixup_toshiba_ohci1394); 451 452 static void pci_post_fixup_toshiba_ohci1394(struct pci_dev *dev) 453 { 454 if (!dmi_check_system(toshiba_ohci1394_dmi_table)) 455 return; /* only applies to certain Toshibas (so far) */ 456 457 /* Restore config space on Toshiba laptops */ 458 pci_write_config_word(dev, PCI_CACHE_LINE_SIZE, toshiba_line_size); 459 pci_read_config_byte(dev, PCI_INTERRUPT_LINE, (u8 *)&dev->irq); 460 pci_write_config_dword(dev, PCI_BASE_ADDRESS_0, 461 pci_resource_start(dev, 0)); 462 pci_write_config_dword(dev, PCI_BASE_ADDRESS_1, 463 pci_resource_start(dev, 1)); 464 } 465 DECLARE_PCI_FIXUP_ENABLE(PCI_VENDOR_ID_TI, 0x8032, 466 pci_post_fixup_toshiba_ohci1394); 467 468 469 /* 470 * Prevent the BIOS trapping accesses to the Cyrix CS5530A video device 471 * configuration space. 472 */ 473 static void pci_early_fixup_cyrix_5530(struct pci_dev *dev) 474 { 475 u8 r; 476 /* clear 'F4 Video Configuration Trap' bit */ 477 pci_read_config_byte(dev, 0x42, &r); 478 r &= 0xfd; 479 pci_write_config_byte(dev, 0x42, r); 480 } 481 DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_CYRIX, PCI_DEVICE_ID_CYRIX_5530_LEGACY, 482 pci_early_fixup_cyrix_5530); 483 DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_CYRIX, PCI_DEVICE_ID_CYRIX_5530_LEGACY, 484 pci_early_fixup_cyrix_5530); 485 486 /* 487 * Siemens Nixdorf AG FSC Multiprocessor Interrupt Controller: 488 * prevent update of the BAR0, which doesn't look like a normal BAR. 489 */ 490 static void pci_siemens_interrupt_controller(struct pci_dev *dev) 491 { 492 dev->resource[0].flags |= IORESOURCE_PCI_FIXED; 493 } 494 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_SIEMENS, 0x0015, 495 pci_siemens_interrupt_controller); 496 497 /* 498 * SB600: Disable BAR1 on device 14.0 to avoid HPET resources from 499 * confusing the PCI engine: 500 */ 501 static void sb600_disable_hpet_bar(struct pci_dev *dev) 502 { 503 u8 val; 504 505 /* 506 * The SB600 and SB700 both share the same device 507 * ID, but the PM register 0x55 does something different 508 * for the SB700, so make sure we are dealing with the 509 * SB600 before touching the bit: 510 */ 511 512 pci_read_config_byte(dev, 0x08, &val); 513 514 if (val < 0x2F) { 515 outb(0x55, 0xCD6); 516 val = inb(0xCD7); 517 518 /* Set bit 7 in PM register 0x55 */ 519 outb(0x55, 0xCD6); 520 outb(val | 0x80, 0xCD7); 521 } 522 } 523 DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_ATI, 0x4385, sb600_disable_hpet_bar); 524 525 #ifdef CONFIG_HPET_TIMER 526 static void sb600_hpet_quirk(struct pci_dev *dev) 527 { 528 struct resource *r = &dev->resource[1]; 529 530 if (r->flags & IORESOURCE_MEM && r->start == hpet_address) { 531 r->flags |= IORESOURCE_PCI_FIXED; 532 dev_info(&dev->dev, "reg 0x14 contains HPET; making it immovable\n"); 533 } 534 } 535 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_ATI, 0x4385, sb600_hpet_quirk); 536 #endif 537 538 /* 539 * Twinhead H12Y needs us to block out a region otherwise we map devices 540 * there and any access kills the box. 541 * 542 * See: https://bugzilla.kernel.org/show_bug.cgi?id=10231 543 * 544 * Match off the LPC and svid/sdid (older kernels lose the bridge subvendor) 545 */ 546 static void twinhead_reserve_killing_zone(struct pci_dev *dev) 547 { 548 if (dev->subsystem_vendor == 0x14FF && dev->subsystem_device == 0xA003) { 549 pr_info("Reserving memory on Twinhead H12Y\n"); 550 request_mem_region(0xFFB00000, 0x100000, "twinhead"); 551 } 552 } 553 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x27B9, twinhead_reserve_killing_zone); 554 555 static void pci_bdwep_bar(struct pci_dev *dev) 556 { 557 dev->non_compliant_bars = 1; 558 } 559 DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_INTEL, 0x6fa0, pci_bdwep_bar); 560 DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_INTEL, 0x6fc0, pci_bdwep_bar); 561