1 // SPDX-License-Identifier: GPL-2.0 2 #include <linux/linkage.h> 3 #include <linux/errno.h> 4 #include <linux/signal.h> 5 #include <linux/sched.h> 6 #include <linux/ioport.h> 7 #include <linux/interrupt.h> 8 #include <linux/irq.h> 9 #include <linux/timex.h> 10 #include <linux/random.h> 11 #include <linux/kprobes.h> 12 #include <linux/init.h> 13 #include <linux/kernel_stat.h> 14 #include <linux/device.h> 15 #include <linux/bitops.h> 16 #include <linux/acpi.h> 17 #include <linux/io.h> 18 #include <linux/delay.h> 19 20 #include <linux/atomic.h> 21 #include <asm/timer.h> 22 #include <asm/hw_irq.h> 23 #include <asm/pgtable.h> 24 #include <asm/desc.h> 25 #include <asm/apic.h> 26 #include <asm/setup.h> 27 #include <asm/i8259.h> 28 #include <asm/traps.h> 29 #include <asm/prom.h> 30 31 /* 32 * ISA PIC or low IO-APIC triggered (INTA-cycle or APIC) interrupts: 33 * (these are usually mapped to vectors 0x30-0x3f) 34 */ 35 36 /* 37 * The IO-APIC gives us many more interrupt sources. Most of these 38 * are unused but an SMP system is supposed to have enough memory ... 39 * sometimes (mostly wrt. hw bugs) we get corrupted vectors all 40 * across the spectrum, so we really want to be prepared to get all 41 * of these. Plus, more powerful systems might have more than 64 42 * IO-APIC registers. 43 * 44 * (these are usually mapped into the 0x30-0xff vector range) 45 */ 46 47 DEFINE_PER_CPU(vector_irq_t, vector_irq) = { 48 [0 ... NR_VECTORS - 1] = VECTOR_UNUSED, 49 }; 50 51 void __init init_ISA_irqs(void) 52 { 53 struct irq_chip *chip = legacy_pic->chip; 54 int i; 55 56 /* 57 * Try to set up the through-local-APIC virtual wire mode earlier. 58 * 59 * On some 32-bit UP machines, whose APIC has been disabled by BIOS 60 * and then got re-enabled by "lapic", it hangs at boot time without this. 61 */ 62 init_bsp_APIC(); 63 64 legacy_pic->init(0); 65 66 for (i = 0; i < nr_legacy_irqs(); i++) 67 irq_set_chip_and_handler(i, chip, handle_level_irq); 68 } 69 70 void __init init_IRQ(void) 71 { 72 int i; 73 74 /* 75 * On cpu 0, Assign ISA_IRQ_VECTOR(irq) to IRQ 0..15. 76 * If these IRQ's are handled by legacy interrupt-controllers like PIC, 77 * then this configuration will likely be static after the boot. If 78 * these IRQs are handled by more modern controllers like IO-APIC, 79 * then this vector space can be freed and re-used dynamically as the 80 * irq's migrate etc. 81 */ 82 for (i = 0; i < nr_legacy_irqs(); i++) 83 per_cpu(vector_irq, 0)[ISA_IRQ_VECTOR(i)] = irq_to_desc(i); 84 85 BUG_ON(irq_init_percpu_irqstack(smp_processor_id())); 86 87 x86_init.irqs.intr_init(); 88 } 89 90 void __init native_init_IRQ(void) 91 { 92 /* Execute any quirks before the call gates are initialised: */ 93 x86_init.irqs.pre_vector_init(); 94 95 idt_setup_apic_and_irq_gates(); 96 lapic_assign_system_vectors(); 97 98 if (!acpi_ioapic && !of_ioapic && nr_legacy_irqs()) { 99 /* IRQ2 is cascade interrupt to second interrupt controller */ 100 if (request_irq(2, no_action, IRQF_NO_THREAD, "cascade", NULL)) 101 pr_err("%s: request_irq() failed\n", "cascade"); 102 } 103 } 104