1 /* 2 * ecc.h: Definitions and defines for the external cache/memory 3 * controller on the sun4m. 4 * 5 * Copyright (C) 1995 David S. Miller (davem@caip.rutgers.edu) 6 */ 7 8 #ifndef _SPARC_ECC_H 9 #define _SPARC_ECC_H 10 11 /* These registers are accessed through the SRMMU passthrough ASI 0x20 */ 12 #define ECC_ENABLE 0x00000000 /* ECC enable register */ 13 #define ECC_FSTATUS 0x00000008 /* ECC fault status register */ 14 #define ECC_FADDR 0x00000010 /* ECC fault address register */ 15 #define ECC_DIGNOSTIC 0x00000018 /* ECC diagnostics register */ 16 #define ECC_MBAENAB 0x00000020 /* MBus arbiter enable register */ 17 #define ECC_DMESG 0x00001000 /* Diagnostic message passing area */ 18 19 /* ECC MBus Arbiter Enable register: 20 * 21 * ---------------------------------------- 22 * | |SBUS|MOD3|MOD2|MOD1|RSV| 23 * ---------------------------------------- 24 * 31 5 4 3 2 1 0 25 * 26 * SBUS: Enable MBus Arbiter on the SBus 0=off 1=on 27 * MOD3: Enable MBus Arbiter on MBus module 3 0=off 1=on 28 * MOD2: Enable MBus Arbiter on MBus module 2 0=off 1=on 29 * MOD1: Enable MBus Arbiter on MBus module 1 0=off 1=on 30 */ 31 32 #define ECC_MBAE_SBUS 0x00000010 33 #define ECC_MBAE_MOD3 0x00000008 34 #define ECC_MBAE_MOD2 0x00000004 35 #define ECC_MBAE_MOD1 0x00000002 36 37 /* ECC Fault Control Register layout: 38 * 39 * ----------------------------- 40 * | RESV | ECHECK | EINT | 41 * ----------------------------- 42 * 31 2 1 0 43 * 44 * ECHECK: Enable ECC checking. 0=off 1=on 45 * EINT: Enable Interrupts for correctable errors. 0=off 1=on 46 */ 47 #define ECC_FCR_CHECK 0x00000002 48 #define ECC_FCR_INTENAB 0x00000001 49 50 /* ECC Fault Address Register Zero layout: 51 * 52 * ----------------------------------------------------- 53 * | MID | S | RSV | VA | BM |AT| C| SZ |TYP| PADDR | 54 * ----------------------------------------------------- 55 * 31-28 27 26-22 21-14 13 12 11 10-8 7-4 3-0 56 * 57 * MID: ModuleID of the faulting processor. ie. who did it? 58 * S: Supervisor/Privileged access? 0=no 1=yes 59 * VA: Bits 19-12 of the virtual faulting address, these are the 60 * superset bits in the virtual cache and can be used for 61 * a flush operation if necessary. 62 * BM: Boot mode? 0=no 1=yes This is just like the SRMMU boot 63 * mode bit. 64 * AT: Did this fault happen during an atomic instruction? 0=no 65 * 1=yes. This means either an 'ldstub' or 'swap' instruction 66 * was in progress (but not finished) when this fault happened. 67 * This indicated whether the bus was locked when the fault 68 * occurred. 69 * C: Did the pte for this access indicate that it was cacheable? 70 * 0=no 1=yes 71 * SZ: The size of the transaction. 72 * TYP: The transaction type. 73 * PADDR: Bits 35-32 of the physical address for the fault. 74 */ 75 #define ECC_FADDR0_MIDMASK 0xf0000000 76 #define ECC_FADDR0_S 0x08000000 77 #define ECC_FADDR0_VADDR 0x003fc000 78 #define ECC_FADDR0_BMODE 0x00002000 79 #define ECC_FADDR0_ATOMIC 0x00001000 80 #define ECC_FADDR0_CACHE 0x00000800 81 #define ECC_FADDR0_SIZE 0x00000700 82 #define ECC_FADDR0_TYPE 0x000000f0 83 #define ECC_FADDR0_PADDR 0x0000000f 84 85 /* ECC Fault Address Register One layout: 86 * 87 * ------------------------------------- 88 * | Physical Address 31-0 | 89 * ------------------------------------- 90 * 31 0 91 * 92 * You get the upper 4 bits of the physical address from the 93 * PADDR field in ECC Fault Address Zero register. 94 */ 95 96 /* ECC Fault Status Register layout: 97 * 98 * ---------------------------------------------- 99 * | RESV|C2E|MULT|SYNDROME|DWORD|UNC|TIMEO|BS|C| 100 * ---------------------------------------------- 101 * 31-18 17 16 15-8 7-4 3 2 1 0 102 * 103 * C2E: A C2 graphics error occurred. 0=no 1=yes (SS10 only) 104 * MULT: Multiple errors occurred ;-O 0=no 1=prom_panic(yes) 105 * SYNDROME: Controller is mentally unstable. 106 * DWORD: 107 * UNC: Uncorrectable error. 0=no 1=yes 108 * TIMEO: Timeout occurred. 0=no 1=yes 109 * BS: C2 graphics bad slot access. 0=no 1=yes (SS10 only) 110 * C: Correctable error? 0=no 1=yes 111 */ 112 113 #define ECC_FSR_C2ERR 0x00020000 114 #define ECC_FSR_MULT 0x00010000 115 #define ECC_FSR_SYND 0x0000ff00 116 #define ECC_FSR_DWORD 0x000000f0 117 #define ECC_FSR_UNC 0x00000008 118 #define ECC_FSR_TIMEO 0x00000004 119 #define ECC_FSR_BADSLOT 0x00000002 120 #define ECC_FSR_C 0x00000001 121 122 #endif /* !(_SPARC_ECC_H) */ 123