1 #include <linux/kernel.h> 2 #include <linux/types.h> 3 #include <linux/init.h> 4 #include <linux/delay.h> 5 #include <linux/pci.h> 6 #include <linux/io.h> 7 #include "pci-sh4.h" 8 9 int __init pcibios_map_platform_irq(struct pci_dev *, u8 slot, u8 pin) 10 { 11 switch (slot) { 12 case 0: return 13; 13 case 1: return 13; /* AMD Ethernet controller */ 14 case 2: return -1; 15 case 3: return -1; 16 case 4: return -1; 17 default: 18 printk("PCI: Bad IRQ mapping request for slot %d\n", slot); 19 return -1; 20 } 21 } 22 23 #define PCIMCR_MRSET_OFF 0xBFFFFFFF 24 #define PCIMCR_RFSH_OFF 0xFFFFFFFB 25 26 /* 27 * Only long word accesses of the PCIC's internal local registers and the 28 * configuration registers from the CPU is supported. 29 */ 30 #define PCIC_WRITE(x,v) writel((v), PCI_REG(x)) 31 #define PCIC_READ(x) readl(PCI_REG(x)) 32 33 /* 34 * Description: This function sets up and initializes the pcic, sets 35 * up the BARS, maps the DRAM into the address space etc, etc. 36 */ 37 int pci_fixup_pcic(struct pci_channel *chan) 38 { 39 unsigned long bcr1, wcr1, wcr2, wcr3, mcr; 40 unsigned short bcr2; 41 42 /* 43 * Initialize the slave bus controller on the pcic. The values used 44 * here should not be hardcoded, but they should be taken from the bsc 45 * on the processor, to make this function as generic as possible. 46 * (i.e. Another sbc may usr different SDRAM timing settings -- in order 47 * for the pcic to work, its settings need to be exactly the same.) 48 */ 49 bcr1 = (*(volatile unsigned long*)(SH7751_BCR1)); 50 bcr2 = (*(volatile unsigned short*)(SH7751_BCR2)); 51 wcr1 = (*(volatile unsigned long*)(SH7751_WCR1)); 52 wcr2 = (*(volatile unsigned long*)(SH7751_WCR2)); 53 wcr3 = (*(volatile unsigned long*)(SH7751_WCR3)); 54 mcr = (*(volatile unsigned long*)(SH7751_MCR)); 55 56 bcr1 = bcr1 | 0x00080000; /* Enable Bit 19, BREQEN */ 57 (*(volatile unsigned long*)(SH7751_BCR1)) = bcr1; 58 59 bcr1 = bcr1 | 0x40080000; /* Enable Bit 19 BREQEN, set PCIC to slave */ 60 PCIC_WRITE(SH7751_PCIBCR1, bcr1); /* PCIC BCR1 */ 61 PCIC_WRITE(SH7751_PCIBCR2, bcr2); /* PCIC BCR2 */ 62 PCIC_WRITE(SH7751_PCIWCR1, wcr1); /* PCIC WCR1 */ 63 PCIC_WRITE(SH7751_PCIWCR2, wcr2); /* PCIC WCR2 */ 64 PCIC_WRITE(SH7751_PCIWCR3, wcr3); /* PCIC WCR3 */ 65 mcr = (mcr & PCIMCR_MRSET_OFF) & PCIMCR_RFSH_OFF; 66 PCIC_WRITE(SH7751_PCIMCR, mcr); /* PCIC MCR */ 67 68 69 /* Enable all interrupts, so we know what to fix */ 70 PCIC_WRITE(SH7751_PCIINTM, 0x0000c3ff); 71 PCIC_WRITE(SH7751_PCIAINTM, 0x0000380f); 72 73 /* Set up standard PCI config registers */ 74 PCIC_WRITE(SH7751_PCICONF1, 0xF39000C7); /* Bus Master, Mem & I/O access */ 75 PCIC_WRITE(SH7751_PCICONF2, 0x00000000); /* PCI Class code & Revision ID */ 76 PCIC_WRITE(SH7751_PCICONF4, 0xab000001); /* PCI I/O address (local regs) */ 77 PCIC_WRITE(SH7751_PCICONF5, 0x0c000000); /* PCI MEM address (local RAM) */ 78 PCIC_WRITE(SH7751_PCICONF6, 0xd0000000); /* PCI MEM address (unused) */ 79 PCIC_WRITE(SH7751_PCICONF11, 0x35051054); /* PCI Subsystem ID & Vendor ID */ 80 PCIC_WRITE(SH7751_PCILSR0, 0x03f00000); /* MEM (full 64M exposed) */ 81 PCIC_WRITE(SH7751_PCILSR1, 0x00000000); /* MEM (unused) */ 82 PCIC_WRITE(SH7751_PCILAR0, 0x0c000000); /* MEM (direct map from PCI) */ 83 PCIC_WRITE(SH7751_PCILAR1, 0x00000000); /* MEM (unused) */ 84 85 /* Now turn it on... */ 86 PCIC_WRITE(SH7751_PCICR, 0xa5000001); 87 88 /* 89 * Set PCIMBR and PCIIOBR here, assuming a single window 90 * (16M MEM, 256K IO) is enough. If a larger space is 91 * needed, the readx/writex and inx/outx functions will 92 * have to do more (e.g. setting registers for each call). 93 */ 94 95 /* 96 * Set the MBR so PCI address is one-to-one with window, 97 * meaning all calls go straight through... use BUG_ON to 98 * catch erroneous assumption. 99 */ 100 BUG_ON(chan->resources[1].start != SH7751_PCI_MEMORY_BASE); 101 102 PCIC_WRITE(SH7751_PCIMBR, chan->resources[1].start); 103 104 /* Set IOBR for window containing area specified in pci.h */ 105 PCIC_WRITE(SH7751_PCIIOBR, (chan->resources[0].start & SH7751_PCIIOBR_MASK)); 106 107 /* All done, may as well say so... */ 108 printk("SH7751 PCI: Finished initialization of the PCI controller\n"); 109 110 return 1; 111 } 112