1 // SPDX-License-Identifier: GPL-2.0-or-later 2 /* 3 * MPC83xx/85xx/86xx PCI/PCIE support routing. 4 * 5 * Copyright 2007-2012 Freescale Semiconductor, Inc. 6 * Copyright 2008-2009 MontaVista Software, Inc. 7 * 8 * Initial author: Xianghua Xiao <x.xiao@freescale.com> 9 * Recode: ZHANG WEI <wei.zhang@freescale.com> 10 * Rewrite the routing for Frescale PCI and PCI Express 11 * Roy Zang <tie-fei.zang@freescale.com> 12 * MPC83xx PCI-Express support: 13 * Tony Li <tony.li@freescale.com> 14 * Anton Vorontsov <avorontsov@ru.mvista.com> 15 */ 16 #include <linux/kernel.h> 17 #include <linux/pci.h> 18 #include <linux/delay.h> 19 #include <linux/string.h> 20 #include <linux/fsl/edac.h> 21 #include <linux/init.h> 22 #include <linux/interrupt.h> 23 #include <linux/memblock.h> 24 #include <linux/log2.h> 25 #include <linux/platform_device.h> 26 #include <linux/slab.h> 27 #include <linux/suspend.h> 28 #include <linux/syscore_ops.h> 29 #include <linux/uaccess.h> 30 31 #include <asm/io.h> 32 #include <asm/prom.h> 33 #include <asm/pci-bridge.h> 34 #include <asm/ppc-pci.h> 35 #include <asm/machdep.h> 36 #include <asm/mpc85xx.h> 37 #include <asm/disassemble.h> 38 #include <asm/ppc-opcode.h> 39 #include <asm/swiotlb.h> 40 #include <sysdev/fsl_soc.h> 41 #include <sysdev/fsl_pci.h> 42 43 static int fsl_pcie_bus_fixup, is_mpc83xx_pci; 44 45 static void quirk_fsl_pcie_early(struct pci_dev *dev) 46 { 47 u8 hdr_type; 48 49 /* if we aren't a PCIe don't bother */ 50 if (!pci_is_pcie(dev)) 51 return; 52 53 /* if we aren't in host mode don't bother */ 54 pci_read_config_byte(dev, PCI_HEADER_TYPE, &hdr_type); 55 if ((hdr_type & 0x7f) != PCI_HEADER_TYPE_BRIDGE) 56 return; 57 58 dev->class = PCI_CLASS_BRIDGE_PCI_NORMAL; 59 fsl_pcie_bus_fixup = 1; 60 return; 61 } 62 63 static int fsl_indirect_read_config(struct pci_bus *, unsigned int, 64 int, int, u32 *); 65 66 static int fsl_pcie_check_link(struct pci_controller *hose) 67 { 68 u32 val = 0; 69 70 if (hose->indirect_type & PPC_INDIRECT_TYPE_FSL_CFG_REG_LINK) { 71 if (hose->ops->read == fsl_indirect_read_config) 72 __indirect_read_config(hose, hose->first_busno, 0, 73 PCIE_LTSSM, 4, &val); 74 else 75 early_read_config_dword(hose, 0, 0, PCIE_LTSSM, &val); 76 if (val < PCIE_LTSSM_L0) 77 return 1; 78 } else { 79 struct ccsr_pci __iomem *pci = hose->private_data; 80 /* for PCIe IP rev 3.0 or greater use CSR0 for link state */ 81 val = (in_be32(&pci->pex_csr0) & PEX_CSR0_LTSSM_MASK) 82 >> PEX_CSR0_LTSSM_SHIFT; 83 if (val != PEX_CSR0_LTSSM_L0) 84 return 1; 85 } 86 87 return 0; 88 } 89 90 static int fsl_indirect_read_config(struct pci_bus *bus, unsigned int devfn, 91 int offset, int len, u32 *val) 92 { 93 struct pci_controller *hose = pci_bus_to_host(bus); 94 95 if (fsl_pcie_check_link(hose)) 96 hose->indirect_type |= PPC_INDIRECT_TYPE_NO_PCIE_LINK; 97 else 98 hose->indirect_type &= ~PPC_INDIRECT_TYPE_NO_PCIE_LINK; 99 100 return indirect_read_config(bus, devfn, offset, len, val); 101 } 102 103 #if defined(CONFIG_FSL_SOC_BOOKE) || defined(CONFIG_PPC_86xx) 104 105 static struct pci_ops fsl_indirect_pcie_ops = 106 { 107 .read = fsl_indirect_read_config, 108 .write = indirect_write_config, 109 }; 110 111 static u64 pci64_dma_offset; 112 113 #ifdef CONFIG_SWIOTLB 114 static void pci_dma_dev_setup_swiotlb(struct pci_dev *pdev) 115 { 116 struct pci_controller *hose = pci_bus_to_host(pdev->bus); 117 118 pdev->dev.bus_dma_limit = 119 hose->dma_window_base_cur + hose->dma_window_size - 1; 120 } 121 122 static void setup_swiotlb_ops(struct pci_controller *hose) 123 { 124 if (ppc_swiotlb_enable) 125 hose->controller_ops.dma_dev_setup = pci_dma_dev_setup_swiotlb; 126 } 127 #else 128 static inline void setup_swiotlb_ops(struct pci_controller *hose) {} 129 #endif 130 131 static void fsl_pci_dma_set_mask(struct device *dev, u64 dma_mask) 132 { 133 /* 134 * Fix up PCI devices that are able to DMA to the large inbound 135 * mapping that allows addressing any RAM address from across PCI. 136 */ 137 if (dev_is_pci(dev) && dma_mask >= pci64_dma_offset * 2 - 1) { 138 dev->bus_dma_limit = 0; 139 dev->archdata.dma_offset = pci64_dma_offset; 140 } 141 } 142 143 static int setup_one_atmu(struct ccsr_pci __iomem *pci, 144 unsigned int index, const struct resource *res, 145 resource_size_t offset) 146 { 147 resource_size_t pci_addr = res->start - offset; 148 resource_size_t phys_addr = res->start; 149 resource_size_t size = resource_size(res); 150 u32 flags = 0x80044000; /* enable & mem R/W */ 151 unsigned int i; 152 153 pr_debug("PCI MEM resource start 0x%016llx, size 0x%016llx.\n", 154 (u64)res->start, (u64)size); 155 156 if (res->flags & IORESOURCE_PREFETCH) 157 flags |= 0x10000000; /* enable relaxed ordering */ 158 159 for (i = 0; size > 0; i++) { 160 unsigned int bits = min_t(u32, ilog2(size), 161 __ffs(pci_addr | phys_addr)); 162 163 if (index + i >= 5) 164 return -1; 165 166 out_be32(&pci->pow[index + i].potar, pci_addr >> 12); 167 out_be32(&pci->pow[index + i].potear, (u64)pci_addr >> 44); 168 out_be32(&pci->pow[index + i].powbar, phys_addr >> 12); 169 out_be32(&pci->pow[index + i].powar, flags | (bits - 1)); 170 171 pci_addr += (resource_size_t)1U << bits; 172 phys_addr += (resource_size_t)1U << bits; 173 size -= (resource_size_t)1U << bits; 174 } 175 176 return i; 177 } 178 179 static bool is_kdump(void) 180 { 181 struct device_node *node; 182 183 node = of_find_node_by_type(NULL, "memory"); 184 if (!node) { 185 WARN_ON_ONCE(1); 186 return false; 187 } 188 189 return of_property_read_bool(node, "linux,usable-memory"); 190 } 191 192 /* atmu setup for fsl pci/pcie controller */ 193 static void setup_pci_atmu(struct pci_controller *hose) 194 { 195 struct ccsr_pci __iomem *pci = hose->private_data; 196 int i, j, n, mem_log, win_idx = 3, start_idx = 1, end_idx = 4; 197 u64 mem, sz, paddr_hi = 0; 198 u64 offset = 0, paddr_lo = ULLONG_MAX; 199 u32 pcicsrbar = 0, pcicsrbar_sz; 200 u32 piwar = PIWAR_EN | PIWAR_PF | PIWAR_TGI_LOCAL | 201 PIWAR_READ_SNOOP | PIWAR_WRITE_SNOOP; 202 const u64 *reg; 203 int len; 204 bool setup_inbound; 205 206 /* 207 * If this is kdump, we don't want to trigger a bunch of PCI 208 * errors by closing the window on in-flight DMA. 209 * 210 * We still run most of the function's logic so that things like 211 * hose->dma_window_size still get set. 212 */ 213 setup_inbound = !is_kdump(); 214 215 if (of_device_is_compatible(hose->dn, "fsl,bsc9132-pcie")) { 216 /* 217 * BSC9132 Rev1.0 has an issue where all the PEX inbound 218 * windows have implemented the default target value as 0xf 219 * for CCSR space.In all Freescale legacy devices the target 220 * of 0xf is reserved for local memory space. 9132 Rev1.0 221 * now has local mempry space mapped to target 0x0 instead of 222 * 0xf. Hence adding a workaround to remove the target 0xf 223 * defined for memory space from Inbound window attributes. 224 */ 225 piwar &= ~PIWAR_TGI_LOCAL; 226 } 227 228 if (early_find_capability(hose, 0, 0, PCI_CAP_ID_EXP)) { 229 if (in_be32(&pci->block_rev1) >= PCIE_IP_REV_2_2) { 230 win_idx = 2; 231 start_idx = 0; 232 end_idx = 3; 233 } 234 } 235 236 /* Disable all windows (except powar0 since it's ignored) */ 237 for(i = 1; i < 5; i++) 238 out_be32(&pci->pow[i].powar, 0); 239 240 if (setup_inbound) { 241 for (i = start_idx; i < end_idx; i++) 242 out_be32(&pci->piw[i].piwar, 0); 243 } 244 245 /* Setup outbound MEM window */ 246 for(i = 0, j = 1; i < 3; i++) { 247 if (!(hose->mem_resources[i].flags & IORESOURCE_MEM)) 248 continue; 249 250 paddr_lo = min(paddr_lo, (u64)hose->mem_resources[i].start); 251 paddr_hi = max(paddr_hi, (u64)hose->mem_resources[i].end); 252 253 /* We assume all memory resources have the same offset */ 254 offset = hose->mem_offset[i]; 255 n = setup_one_atmu(pci, j, &hose->mem_resources[i], offset); 256 257 if (n < 0 || j >= 5) { 258 pr_err("Ran out of outbound PCI ATMUs for resource %d!\n", i); 259 hose->mem_resources[i].flags |= IORESOURCE_DISABLED; 260 } else 261 j += n; 262 } 263 264 /* Setup outbound IO window */ 265 if (hose->io_resource.flags & IORESOURCE_IO) { 266 if (j >= 5) { 267 pr_err("Ran out of outbound PCI ATMUs for IO resource\n"); 268 } else { 269 pr_debug("PCI IO resource start 0x%016llx, size 0x%016llx, " 270 "phy base 0x%016llx.\n", 271 (u64)hose->io_resource.start, 272 (u64)resource_size(&hose->io_resource), 273 (u64)hose->io_base_phys); 274 out_be32(&pci->pow[j].potar, (hose->io_resource.start >> 12)); 275 out_be32(&pci->pow[j].potear, 0); 276 out_be32(&pci->pow[j].powbar, (hose->io_base_phys >> 12)); 277 /* Enable, IO R/W */ 278 out_be32(&pci->pow[j].powar, 0x80088000 279 | (ilog2(hose->io_resource.end 280 - hose->io_resource.start + 1) - 1)); 281 } 282 } 283 284 /* convert to pci address space */ 285 paddr_hi -= offset; 286 paddr_lo -= offset; 287 288 if (paddr_hi == paddr_lo) { 289 pr_err("%pOF: No outbound window space\n", hose->dn); 290 return; 291 } 292 293 if (paddr_lo == 0) { 294 pr_err("%pOF: No space for inbound window\n", hose->dn); 295 return; 296 } 297 298 /* setup PCSRBAR/PEXCSRBAR */ 299 early_write_config_dword(hose, 0, 0, PCI_BASE_ADDRESS_0, 0xffffffff); 300 early_read_config_dword(hose, 0, 0, PCI_BASE_ADDRESS_0, &pcicsrbar_sz); 301 pcicsrbar_sz = ~pcicsrbar_sz + 1; 302 303 if (paddr_hi < (0x100000000ull - pcicsrbar_sz) || 304 (paddr_lo > 0x100000000ull)) 305 pcicsrbar = 0x100000000ull - pcicsrbar_sz; 306 else 307 pcicsrbar = (paddr_lo - pcicsrbar_sz) & -pcicsrbar_sz; 308 early_write_config_dword(hose, 0, 0, PCI_BASE_ADDRESS_0, pcicsrbar); 309 310 paddr_lo = min(paddr_lo, (u64)pcicsrbar); 311 312 pr_info("%pOF: PCICSRBAR @ 0x%x\n", hose->dn, pcicsrbar); 313 314 /* Setup inbound mem window */ 315 mem = memblock_end_of_DRAM(); 316 pr_info("%s: end of DRAM %llx\n", __func__, mem); 317 318 /* 319 * The msi-address-64 property, if it exists, indicates the physical 320 * address of the MSIIR register. Normally, this register is located 321 * inside CCSR, so the ATMU that covers all of CCSR is used. But if 322 * this property exists, then we normally need to create a new ATMU 323 * for it. For now, however, we cheat. The only entity that creates 324 * this property is the Freescale hypervisor, and the address is 325 * specified in the partition configuration. Typically, the address 326 * is located in the page immediately after the end of DDR. If so, we 327 * can avoid allocating a new ATMU by extending the DDR ATMU by one 328 * page. 329 */ 330 reg = of_get_property(hose->dn, "msi-address-64", &len); 331 if (reg && (len == sizeof(u64))) { 332 u64 address = be64_to_cpup(reg); 333 334 if ((address >= mem) && (address < (mem + PAGE_SIZE))) { 335 pr_info("%pOF: extending DDR ATMU to cover MSIIR", hose->dn); 336 mem += PAGE_SIZE; 337 } else { 338 /* TODO: Create a new ATMU for MSIIR */ 339 pr_warn("%pOF: msi-address-64 address of %llx is " 340 "unsupported\n", hose->dn, address); 341 } 342 } 343 344 sz = min(mem, paddr_lo); 345 mem_log = ilog2(sz); 346 347 /* PCIe can overmap inbound & outbound since RX & TX are separated */ 348 if (early_find_capability(hose, 0, 0, PCI_CAP_ID_EXP)) { 349 /* Size window to exact size if power-of-two or one size up */ 350 if ((1ull << mem_log) != mem) { 351 mem_log++; 352 if ((1ull << mem_log) > mem) 353 pr_info("%pOF: Setting PCI inbound window " 354 "greater than memory size\n", hose->dn); 355 } 356 357 piwar |= ((mem_log - 1) & PIWAR_SZ_MASK); 358 359 if (setup_inbound) { 360 /* Setup inbound memory window */ 361 out_be32(&pci->piw[win_idx].pitar, 0x00000000); 362 out_be32(&pci->piw[win_idx].piwbar, 0x00000000); 363 out_be32(&pci->piw[win_idx].piwar, piwar); 364 } 365 366 win_idx--; 367 hose->dma_window_base_cur = 0x00000000; 368 hose->dma_window_size = (resource_size_t)sz; 369 370 /* 371 * if we have >4G of memory setup second PCI inbound window to 372 * let devices that are 64-bit address capable to work w/o 373 * SWIOTLB and access the full range of memory 374 */ 375 if (sz != mem) { 376 mem_log = ilog2(mem); 377 378 /* Size window up if we dont fit in exact power-of-2 */ 379 if ((1ull << mem_log) != mem) 380 mem_log++; 381 382 piwar = (piwar & ~PIWAR_SZ_MASK) | (mem_log - 1); 383 pci64_dma_offset = 1ULL << mem_log; 384 385 if (setup_inbound) { 386 /* Setup inbound memory window */ 387 out_be32(&pci->piw[win_idx].pitar, 0x00000000); 388 out_be32(&pci->piw[win_idx].piwbear, 389 pci64_dma_offset >> 44); 390 out_be32(&pci->piw[win_idx].piwbar, 391 pci64_dma_offset >> 12); 392 out_be32(&pci->piw[win_idx].piwar, piwar); 393 } 394 395 /* 396 * install our own dma_set_mask handler to fixup dma_ops 397 * and dma_offset 398 */ 399 ppc_md.dma_set_mask = fsl_pci_dma_set_mask; 400 401 pr_info("%pOF: Setup 64-bit PCI DMA window\n", hose->dn); 402 } 403 } else { 404 u64 paddr = 0; 405 406 if (setup_inbound) { 407 /* Setup inbound memory window */ 408 out_be32(&pci->piw[win_idx].pitar, paddr >> 12); 409 out_be32(&pci->piw[win_idx].piwbar, paddr >> 12); 410 out_be32(&pci->piw[win_idx].piwar, 411 (piwar | (mem_log - 1))); 412 } 413 414 win_idx--; 415 paddr += 1ull << mem_log; 416 sz -= 1ull << mem_log; 417 418 if (sz) { 419 mem_log = ilog2(sz); 420 piwar |= (mem_log - 1); 421 422 if (setup_inbound) { 423 out_be32(&pci->piw[win_idx].pitar, 424 paddr >> 12); 425 out_be32(&pci->piw[win_idx].piwbar, 426 paddr >> 12); 427 out_be32(&pci->piw[win_idx].piwar, piwar); 428 } 429 430 win_idx--; 431 paddr += 1ull << mem_log; 432 } 433 434 hose->dma_window_base_cur = 0x00000000; 435 hose->dma_window_size = (resource_size_t)paddr; 436 } 437 438 if (hose->dma_window_size < mem) { 439 #ifdef CONFIG_SWIOTLB 440 ppc_swiotlb_enable = 1; 441 #else 442 pr_err("%pOF: ERROR: Memory size exceeds PCI ATMU ability to " 443 "map - enable CONFIG_SWIOTLB to avoid dma errors.\n", 444 hose->dn); 445 #endif 446 /* adjusting outbound windows could reclaim space in mem map */ 447 if (paddr_hi < 0xffffffffull) 448 pr_warn("%pOF: WARNING: Outbound window cfg leaves " 449 "gaps in memory map. Adjusting the memory map " 450 "could reduce unnecessary bounce buffering.\n", 451 hose->dn); 452 453 pr_info("%pOF: DMA window size is 0x%llx\n", hose->dn, 454 (u64)hose->dma_window_size); 455 } 456 } 457 458 static void setup_pci_cmd(struct pci_controller *hose) 459 { 460 u16 cmd; 461 int cap_x; 462 463 early_read_config_word(hose, 0, 0, PCI_COMMAND, &cmd); 464 cmd |= PCI_COMMAND_SERR | PCI_COMMAND_MASTER | PCI_COMMAND_MEMORY 465 | PCI_COMMAND_IO; 466 early_write_config_word(hose, 0, 0, PCI_COMMAND, cmd); 467 468 cap_x = early_find_capability(hose, 0, 0, PCI_CAP_ID_PCIX); 469 if (cap_x) { 470 int pci_x_cmd = cap_x + PCI_X_CMD; 471 cmd = PCI_X_CMD_MAX_SPLIT | PCI_X_CMD_MAX_READ 472 | PCI_X_CMD_ERO | PCI_X_CMD_DPERR_E; 473 early_write_config_word(hose, 0, 0, pci_x_cmd, cmd); 474 } else { 475 early_write_config_byte(hose, 0, 0, PCI_LATENCY_TIMER, 0x80); 476 } 477 } 478 479 void fsl_pcibios_fixup_bus(struct pci_bus *bus) 480 { 481 struct pci_controller *hose = pci_bus_to_host(bus); 482 int i, is_pcie = 0, no_link; 483 484 /* The root complex bridge comes up with bogus resources, 485 * we copy the PHB ones in. 486 * 487 * With the current generic PCI code, the PHB bus no longer 488 * has bus->resource[0..4] set, so things are a bit more 489 * tricky. 490 */ 491 492 if (fsl_pcie_bus_fixup) 493 is_pcie = early_find_capability(hose, 0, 0, PCI_CAP_ID_EXP); 494 no_link = !!(hose->indirect_type & PPC_INDIRECT_TYPE_NO_PCIE_LINK); 495 496 if (bus->parent == hose->bus && (is_pcie || no_link)) { 497 for (i = 0; i < PCI_BRIDGE_RESOURCE_NUM; ++i) { 498 struct resource *res = bus->resource[i]; 499 struct resource *par; 500 501 if (!res) 502 continue; 503 if (i == 0) 504 par = &hose->io_resource; 505 else if (i < 4) 506 par = &hose->mem_resources[i-1]; 507 else par = NULL; 508 509 res->start = par ? par->start : 0; 510 res->end = par ? par->end : 0; 511 res->flags = par ? par->flags : 0; 512 } 513 } 514 } 515 516 int fsl_add_bridge(struct platform_device *pdev, int is_primary) 517 { 518 int len; 519 struct pci_controller *hose; 520 struct resource rsrc; 521 const int *bus_range; 522 u8 hdr_type, progif; 523 struct device_node *dev; 524 struct ccsr_pci __iomem *pci; 525 u16 temp; 526 u32 svr = mfspr(SPRN_SVR); 527 528 dev = pdev->dev.of_node; 529 530 if (!of_device_is_available(dev)) { 531 pr_warn("%pOF: disabled\n", dev); 532 return -ENODEV; 533 } 534 535 pr_debug("Adding PCI host bridge %pOF\n", dev); 536 537 /* Fetch host bridge registers address */ 538 if (of_address_to_resource(dev, 0, &rsrc)) { 539 printk(KERN_WARNING "Can't get pci register base!"); 540 return -ENOMEM; 541 } 542 543 /* Get bus range if any */ 544 bus_range = of_get_property(dev, "bus-range", &len); 545 if (bus_range == NULL || len < 2 * sizeof(int)) 546 printk(KERN_WARNING "Can't get bus-range for %pOF, assume" 547 " bus 0\n", dev); 548 549 pci_add_flags(PCI_REASSIGN_ALL_BUS); 550 hose = pcibios_alloc_controller(dev); 551 if (!hose) 552 return -ENOMEM; 553 554 /* set platform device as the parent */ 555 hose->parent = &pdev->dev; 556 hose->first_busno = bus_range ? bus_range[0] : 0x0; 557 hose->last_busno = bus_range ? bus_range[1] : 0xff; 558 559 pr_debug("PCI memory map start 0x%016llx, size 0x%016llx\n", 560 (u64)rsrc.start, (u64)resource_size(&rsrc)); 561 562 pci = hose->private_data = ioremap(rsrc.start, resource_size(&rsrc)); 563 if (!hose->private_data) 564 goto no_bridge; 565 566 setup_indirect_pci(hose, rsrc.start, rsrc.start + 0x4, 567 PPC_INDIRECT_TYPE_BIG_ENDIAN); 568 569 if (in_be32(&pci->block_rev1) < PCIE_IP_REV_3_0) 570 hose->indirect_type |= PPC_INDIRECT_TYPE_FSL_CFG_REG_LINK; 571 572 if (early_find_capability(hose, 0, 0, PCI_CAP_ID_EXP)) { 573 /* use fsl_indirect_read_config for PCIe */ 574 hose->ops = &fsl_indirect_pcie_ops; 575 /* For PCIE read HEADER_TYPE to identify controller mode */ 576 early_read_config_byte(hose, 0, 0, PCI_HEADER_TYPE, &hdr_type); 577 if ((hdr_type & 0x7f) != PCI_HEADER_TYPE_BRIDGE) 578 goto no_bridge; 579 580 } else { 581 /* For PCI read PROG to identify controller mode */ 582 early_read_config_byte(hose, 0, 0, PCI_CLASS_PROG, &progif); 583 if ((progif & 1) && 584 !of_property_read_bool(dev, "fsl,pci-agent-force-enum")) 585 goto no_bridge; 586 } 587 588 setup_pci_cmd(hose); 589 590 /* check PCI express link status */ 591 if (early_find_capability(hose, 0, 0, PCI_CAP_ID_EXP)) { 592 hose->indirect_type |= PPC_INDIRECT_TYPE_EXT_REG | 593 PPC_INDIRECT_TYPE_SURPRESS_PRIMARY_BUS; 594 if (fsl_pcie_check_link(hose)) 595 hose->indirect_type |= PPC_INDIRECT_TYPE_NO_PCIE_LINK; 596 } else { 597 /* 598 * Set PBFR(PCI Bus Function Register)[10] = 1 to 599 * disable the combining of crossing cacheline 600 * boundary requests into one burst transaction. 601 * PCI-X operation is not affected. 602 * Fix erratum PCI 5 on MPC8548 603 */ 604 #define PCI_BUS_FUNCTION 0x44 605 #define PCI_BUS_FUNCTION_MDS 0x400 /* Master disable streaming */ 606 if (((SVR_SOC_VER(svr) == SVR_8543) || 607 (SVR_SOC_VER(svr) == SVR_8545) || 608 (SVR_SOC_VER(svr) == SVR_8547) || 609 (SVR_SOC_VER(svr) == SVR_8548)) && 610 !early_find_capability(hose, 0, 0, PCI_CAP_ID_PCIX)) { 611 early_read_config_word(hose, 0, 0, 612 PCI_BUS_FUNCTION, &temp); 613 temp |= PCI_BUS_FUNCTION_MDS; 614 early_write_config_word(hose, 0, 0, 615 PCI_BUS_FUNCTION, temp); 616 } 617 } 618 619 printk(KERN_INFO "Found FSL PCI host bridge at 0x%016llx. " 620 "Firmware bus number: %d->%d\n", 621 (unsigned long long)rsrc.start, hose->first_busno, 622 hose->last_busno); 623 624 pr_debug(" ->Hose at 0x%p, cfg_addr=0x%p,cfg_data=0x%p\n", 625 hose, hose->cfg_addr, hose->cfg_data); 626 627 /* Interpret the "ranges" property */ 628 /* This also maps the I/O region and sets isa_io/mem_base */ 629 pci_process_bridge_OF_ranges(hose, dev, is_primary); 630 631 /* Setup PEX window registers */ 632 setup_pci_atmu(hose); 633 634 /* Set up controller operations */ 635 setup_swiotlb_ops(hose); 636 637 return 0; 638 639 no_bridge: 640 iounmap(hose->private_data); 641 /* unmap cfg_data & cfg_addr separately if not on same page */ 642 if (((unsigned long)hose->cfg_data & PAGE_MASK) != 643 ((unsigned long)hose->cfg_addr & PAGE_MASK)) 644 iounmap(hose->cfg_data); 645 iounmap(hose->cfg_addr); 646 pcibios_free_controller(hose); 647 return -ENODEV; 648 } 649 #endif /* CONFIG_FSL_SOC_BOOKE || CONFIG_PPC_86xx */ 650 651 DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_FREESCALE, PCI_ANY_ID, 652 quirk_fsl_pcie_early); 653 654 #if defined(CONFIG_PPC_83xx) || defined(CONFIG_PPC_MPC512x) 655 struct mpc83xx_pcie_priv { 656 void __iomem *cfg_type0; 657 void __iomem *cfg_type1; 658 u32 dev_base; 659 }; 660 661 struct pex_inbound_window { 662 u32 ar; 663 u32 tar; 664 u32 barl; 665 u32 barh; 666 }; 667 668 /* 669 * With the convention of u-boot, the PCIE outbound window 0 serves 670 * as configuration transactions outbound. 671 */ 672 #define PEX_OUTWIN0_BAR 0xCA4 673 #define PEX_OUTWIN0_TAL 0xCA8 674 #define PEX_OUTWIN0_TAH 0xCAC 675 #define PEX_RC_INWIN_BASE 0xE60 676 #define PEX_RCIWARn_EN 0x1 677 678 static int mpc83xx_pcie_exclude_device(struct pci_bus *bus, unsigned int devfn) 679 { 680 struct pci_controller *hose = pci_bus_to_host(bus); 681 682 if (hose->indirect_type & PPC_INDIRECT_TYPE_NO_PCIE_LINK) 683 return PCIBIOS_DEVICE_NOT_FOUND; 684 /* 685 * Workaround for the HW bug: for Type 0 configure transactions the 686 * PCI-E controller does not check the device number bits and just 687 * assumes that the device number bits are 0. 688 */ 689 if (bus->number == hose->first_busno || 690 bus->primary == hose->first_busno) { 691 if (devfn & 0xf8) 692 return PCIBIOS_DEVICE_NOT_FOUND; 693 } 694 695 if (ppc_md.pci_exclude_device) { 696 if (ppc_md.pci_exclude_device(hose, bus->number, devfn)) 697 return PCIBIOS_DEVICE_NOT_FOUND; 698 } 699 700 return PCIBIOS_SUCCESSFUL; 701 } 702 703 static void __iomem *mpc83xx_pcie_remap_cfg(struct pci_bus *bus, 704 unsigned int devfn, int offset) 705 { 706 struct pci_controller *hose = pci_bus_to_host(bus); 707 struct mpc83xx_pcie_priv *pcie = hose->dn->data; 708 u32 dev_base = bus->number << 24 | devfn << 16; 709 int ret; 710 711 ret = mpc83xx_pcie_exclude_device(bus, devfn); 712 if (ret) 713 return NULL; 714 715 offset &= 0xfff; 716 717 /* Type 0 */ 718 if (bus->number == hose->first_busno) 719 return pcie->cfg_type0 + offset; 720 721 if (pcie->dev_base == dev_base) 722 goto mapped; 723 724 out_le32(pcie->cfg_type0 + PEX_OUTWIN0_TAL, dev_base); 725 726 pcie->dev_base = dev_base; 727 mapped: 728 return pcie->cfg_type1 + offset; 729 } 730 731 static int mpc83xx_pcie_write_config(struct pci_bus *bus, unsigned int devfn, 732 int offset, int len, u32 val) 733 { 734 struct pci_controller *hose = pci_bus_to_host(bus); 735 736 /* PPC_INDIRECT_TYPE_SURPRESS_PRIMARY_BUS */ 737 if (offset == PCI_PRIMARY_BUS && bus->number == hose->first_busno) 738 val &= 0xffffff00; 739 740 return pci_generic_config_write(bus, devfn, offset, len, val); 741 } 742 743 static struct pci_ops mpc83xx_pcie_ops = { 744 .map_bus = mpc83xx_pcie_remap_cfg, 745 .read = pci_generic_config_read, 746 .write = mpc83xx_pcie_write_config, 747 }; 748 749 static int __init mpc83xx_pcie_setup(struct pci_controller *hose, 750 struct resource *reg) 751 { 752 struct mpc83xx_pcie_priv *pcie; 753 u32 cfg_bar; 754 int ret = -ENOMEM; 755 756 pcie = zalloc_maybe_bootmem(sizeof(*pcie), GFP_KERNEL); 757 if (!pcie) 758 return ret; 759 760 pcie->cfg_type0 = ioremap(reg->start, resource_size(reg)); 761 if (!pcie->cfg_type0) 762 goto err0; 763 764 cfg_bar = in_le32(pcie->cfg_type0 + PEX_OUTWIN0_BAR); 765 if (!cfg_bar) { 766 /* PCI-E isn't configured. */ 767 ret = -ENODEV; 768 goto err1; 769 } 770 771 pcie->cfg_type1 = ioremap(cfg_bar, 0x1000); 772 if (!pcie->cfg_type1) 773 goto err1; 774 775 WARN_ON(hose->dn->data); 776 hose->dn->data = pcie; 777 hose->ops = &mpc83xx_pcie_ops; 778 hose->indirect_type |= PPC_INDIRECT_TYPE_FSL_CFG_REG_LINK; 779 780 out_le32(pcie->cfg_type0 + PEX_OUTWIN0_TAH, 0); 781 out_le32(pcie->cfg_type0 + PEX_OUTWIN0_TAL, 0); 782 783 if (fsl_pcie_check_link(hose)) 784 hose->indirect_type |= PPC_INDIRECT_TYPE_NO_PCIE_LINK; 785 786 return 0; 787 err1: 788 iounmap(pcie->cfg_type0); 789 err0: 790 kfree(pcie); 791 return ret; 792 793 } 794 795 int __init mpc83xx_add_bridge(struct device_node *dev) 796 { 797 int ret; 798 int len; 799 struct pci_controller *hose; 800 struct resource rsrc_reg; 801 struct resource rsrc_cfg; 802 const int *bus_range; 803 int primary; 804 805 is_mpc83xx_pci = 1; 806 807 if (!of_device_is_available(dev)) { 808 pr_warn("%pOF: disabled by the firmware.\n", 809 dev); 810 return -ENODEV; 811 } 812 pr_debug("Adding PCI host bridge %pOF\n", dev); 813 814 /* Fetch host bridge registers address */ 815 if (of_address_to_resource(dev, 0, &rsrc_reg)) { 816 printk(KERN_WARNING "Can't get pci register base!\n"); 817 return -ENOMEM; 818 } 819 820 memset(&rsrc_cfg, 0, sizeof(rsrc_cfg)); 821 822 if (of_address_to_resource(dev, 1, &rsrc_cfg)) { 823 printk(KERN_WARNING 824 "No pci config register base in dev tree, " 825 "using default\n"); 826 /* 827 * MPC83xx supports up to two host controllers 828 * one at 0x8500 has config space registers at 0x8300 829 * one at 0x8600 has config space registers at 0x8380 830 */ 831 if ((rsrc_reg.start & 0xfffff) == 0x8500) 832 rsrc_cfg.start = (rsrc_reg.start & 0xfff00000) + 0x8300; 833 else if ((rsrc_reg.start & 0xfffff) == 0x8600) 834 rsrc_cfg.start = (rsrc_reg.start & 0xfff00000) + 0x8380; 835 } 836 /* 837 * Controller at offset 0x8500 is primary 838 */ 839 if ((rsrc_reg.start & 0xfffff) == 0x8500) 840 primary = 1; 841 else 842 primary = 0; 843 844 /* Get bus range if any */ 845 bus_range = of_get_property(dev, "bus-range", &len); 846 if (bus_range == NULL || len < 2 * sizeof(int)) { 847 printk(KERN_WARNING "Can't get bus-range for %pOF, assume" 848 " bus 0\n", dev); 849 } 850 851 pci_add_flags(PCI_REASSIGN_ALL_BUS); 852 hose = pcibios_alloc_controller(dev); 853 if (!hose) 854 return -ENOMEM; 855 856 hose->first_busno = bus_range ? bus_range[0] : 0; 857 hose->last_busno = bus_range ? bus_range[1] : 0xff; 858 859 if (of_device_is_compatible(dev, "fsl,mpc8314-pcie")) { 860 ret = mpc83xx_pcie_setup(hose, &rsrc_reg); 861 if (ret) 862 goto err0; 863 } else { 864 setup_indirect_pci(hose, rsrc_cfg.start, 865 rsrc_cfg.start + 4, 0); 866 } 867 868 printk(KERN_INFO "Found FSL PCI host bridge at 0x%016llx. " 869 "Firmware bus number: %d->%d\n", 870 (unsigned long long)rsrc_reg.start, hose->first_busno, 871 hose->last_busno); 872 873 pr_debug(" ->Hose at 0x%p, cfg_addr=0x%p,cfg_data=0x%p\n", 874 hose, hose->cfg_addr, hose->cfg_data); 875 876 /* Interpret the "ranges" property */ 877 /* This also maps the I/O region and sets isa_io/mem_base */ 878 pci_process_bridge_OF_ranges(hose, dev, primary); 879 880 return 0; 881 err0: 882 pcibios_free_controller(hose); 883 return ret; 884 } 885 #endif /* CONFIG_PPC_83xx */ 886 887 u64 fsl_pci_immrbar_base(struct pci_controller *hose) 888 { 889 #ifdef CONFIG_PPC_83xx 890 if (is_mpc83xx_pci) { 891 struct mpc83xx_pcie_priv *pcie = hose->dn->data; 892 struct pex_inbound_window *in; 893 int i; 894 895 /* Walk the Root Complex Inbound windows to match IMMR base */ 896 in = pcie->cfg_type0 + PEX_RC_INWIN_BASE; 897 for (i = 0; i < 4; i++) { 898 /* not enabled, skip */ 899 if (!(in_le32(&in[i].ar) & PEX_RCIWARn_EN)) 900 continue; 901 902 if (get_immrbase() == in_le32(&in[i].tar)) 903 return (u64)in_le32(&in[i].barh) << 32 | 904 in_le32(&in[i].barl); 905 } 906 907 printk(KERN_WARNING "could not find PCI BAR matching IMMR\n"); 908 } 909 #endif 910 911 #if defined(CONFIG_FSL_SOC_BOOKE) || defined(CONFIG_PPC_86xx) 912 if (!is_mpc83xx_pci) { 913 u32 base; 914 915 pci_bus_read_config_dword(hose->bus, 916 PCI_DEVFN(0, 0), PCI_BASE_ADDRESS_0, &base); 917 918 /* 919 * For PEXCSRBAR, bit 3-0 indicate prefetchable and 920 * address type. So when getting base address, these 921 * bits should be masked 922 */ 923 base &= PCI_BASE_ADDRESS_MEM_MASK; 924 925 return base; 926 } 927 #endif 928 929 return 0; 930 } 931 932 #ifdef CONFIG_E500 933 static int mcheck_handle_load(struct pt_regs *regs, u32 inst) 934 { 935 unsigned int rd, ra, rb, d; 936 937 rd = get_rt(inst); 938 ra = get_ra(inst); 939 rb = get_rb(inst); 940 d = get_d(inst); 941 942 switch (get_op(inst)) { 943 case 31: 944 switch (get_xop(inst)) { 945 case OP_31_XOP_LWZX: 946 case OP_31_XOP_LWBRX: 947 regs->gpr[rd] = 0xffffffff; 948 break; 949 950 case OP_31_XOP_LWZUX: 951 regs->gpr[rd] = 0xffffffff; 952 regs->gpr[ra] += regs->gpr[rb]; 953 break; 954 955 case OP_31_XOP_LBZX: 956 regs->gpr[rd] = 0xff; 957 break; 958 959 case OP_31_XOP_LBZUX: 960 regs->gpr[rd] = 0xff; 961 regs->gpr[ra] += regs->gpr[rb]; 962 break; 963 964 case OP_31_XOP_LHZX: 965 case OP_31_XOP_LHBRX: 966 regs->gpr[rd] = 0xffff; 967 break; 968 969 case OP_31_XOP_LHZUX: 970 regs->gpr[rd] = 0xffff; 971 regs->gpr[ra] += regs->gpr[rb]; 972 break; 973 974 case OP_31_XOP_LHAX: 975 regs->gpr[rd] = ~0UL; 976 break; 977 978 case OP_31_XOP_LHAUX: 979 regs->gpr[rd] = ~0UL; 980 regs->gpr[ra] += regs->gpr[rb]; 981 break; 982 983 default: 984 return 0; 985 } 986 break; 987 988 case OP_LWZ: 989 regs->gpr[rd] = 0xffffffff; 990 break; 991 992 case OP_LWZU: 993 regs->gpr[rd] = 0xffffffff; 994 regs->gpr[ra] += (s16)d; 995 break; 996 997 case OP_LBZ: 998 regs->gpr[rd] = 0xff; 999 break; 1000 1001 case OP_LBZU: 1002 regs->gpr[rd] = 0xff; 1003 regs->gpr[ra] += (s16)d; 1004 break; 1005 1006 case OP_LHZ: 1007 regs->gpr[rd] = 0xffff; 1008 break; 1009 1010 case OP_LHZU: 1011 regs->gpr[rd] = 0xffff; 1012 regs->gpr[ra] += (s16)d; 1013 break; 1014 1015 case OP_LHA: 1016 regs->gpr[rd] = ~0UL; 1017 break; 1018 1019 case OP_LHAU: 1020 regs->gpr[rd] = ~0UL; 1021 regs->gpr[ra] += (s16)d; 1022 break; 1023 1024 default: 1025 return 0; 1026 } 1027 1028 return 1; 1029 } 1030 1031 static int is_in_pci_mem_space(phys_addr_t addr) 1032 { 1033 struct pci_controller *hose; 1034 struct resource *res; 1035 int i; 1036 1037 list_for_each_entry(hose, &hose_list, list_node) { 1038 if (!(hose->indirect_type & PPC_INDIRECT_TYPE_EXT_REG)) 1039 continue; 1040 1041 for (i = 0; i < 3; i++) { 1042 res = &hose->mem_resources[i]; 1043 if ((res->flags & IORESOURCE_MEM) && 1044 addr >= res->start && addr <= res->end) 1045 return 1; 1046 } 1047 } 1048 return 0; 1049 } 1050 1051 int fsl_pci_mcheck_exception(struct pt_regs *regs) 1052 { 1053 u32 inst; 1054 int ret; 1055 phys_addr_t addr = 0; 1056 1057 /* Let KVM/QEMU deal with the exception */ 1058 if (regs->msr & MSR_GS) 1059 return 0; 1060 1061 #ifdef CONFIG_PHYS_64BIT 1062 addr = mfspr(SPRN_MCARU); 1063 addr <<= 32; 1064 #endif 1065 addr += mfspr(SPRN_MCAR); 1066 1067 if (is_in_pci_mem_space(addr)) { 1068 if (user_mode(regs)) 1069 ret = copy_from_user_nofault(&inst, 1070 (void __user *)regs->nip, sizeof(inst)); 1071 else 1072 ret = get_kernel_nofault(inst, (void *)regs->nip); 1073 1074 if (!ret && mcheck_handle_load(regs, inst)) { 1075 regs_add_return_ip(regs, 4); 1076 return 1; 1077 } 1078 } 1079 1080 return 0; 1081 } 1082 #endif 1083 1084 #if defined(CONFIG_FSL_SOC_BOOKE) || defined(CONFIG_PPC_86xx) 1085 static const struct of_device_id pci_ids[] = { 1086 { .compatible = "fsl,mpc8540-pci", }, 1087 { .compatible = "fsl,mpc8548-pcie", }, 1088 { .compatible = "fsl,mpc8610-pci", }, 1089 { .compatible = "fsl,mpc8641-pcie", }, 1090 { .compatible = "fsl,qoriq-pcie", }, 1091 { .compatible = "fsl,qoriq-pcie-v2.1", }, 1092 { .compatible = "fsl,qoriq-pcie-v2.2", }, 1093 { .compatible = "fsl,qoriq-pcie-v2.3", }, 1094 { .compatible = "fsl,qoriq-pcie-v2.4", }, 1095 { .compatible = "fsl,qoriq-pcie-v3.0", }, 1096 1097 /* 1098 * The following entries are for compatibility with older device 1099 * trees. 1100 */ 1101 { .compatible = "fsl,p1022-pcie", }, 1102 { .compatible = "fsl,p4080-pcie", }, 1103 1104 {}, 1105 }; 1106 1107 struct device_node *fsl_pci_primary; 1108 1109 void __init fsl_pci_assign_primary(void) 1110 { 1111 struct device_node *np; 1112 1113 /* Callers can specify the primary bus using other means. */ 1114 if (fsl_pci_primary) 1115 return; 1116 1117 /* If a PCI host bridge contains an ISA node, it's primary. */ 1118 np = of_find_node_by_type(NULL, "isa"); 1119 while ((fsl_pci_primary = of_get_parent(np))) { 1120 of_node_put(np); 1121 np = fsl_pci_primary; 1122 1123 if (of_match_node(pci_ids, np) && of_device_is_available(np)) 1124 return; 1125 } 1126 1127 /* 1128 * If there's no PCI host bridge with ISA, arbitrarily 1129 * designate one as primary. This can go away once 1130 * various bugs with primary-less systems are fixed. 1131 */ 1132 for_each_matching_node(np, pci_ids) { 1133 if (of_device_is_available(np)) { 1134 fsl_pci_primary = np; 1135 of_node_put(np); 1136 return; 1137 } 1138 } 1139 } 1140 1141 #ifdef CONFIG_PM_SLEEP 1142 static irqreturn_t fsl_pci_pme_handle(int irq, void *dev_id) 1143 { 1144 struct pci_controller *hose = dev_id; 1145 struct ccsr_pci __iomem *pci = hose->private_data; 1146 u32 dr; 1147 1148 dr = in_be32(&pci->pex_pme_mes_dr); 1149 if (!dr) 1150 return IRQ_NONE; 1151 1152 out_be32(&pci->pex_pme_mes_dr, dr); 1153 1154 return IRQ_HANDLED; 1155 } 1156 1157 static int fsl_pci_pme_probe(struct pci_controller *hose) 1158 { 1159 struct ccsr_pci __iomem *pci; 1160 struct pci_dev *dev; 1161 int pme_irq; 1162 int res; 1163 u16 pms; 1164 1165 /* Get hose's pci_dev */ 1166 dev = list_first_entry(&hose->bus->devices, typeof(*dev), bus_list); 1167 1168 /* PME Disable */ 1169 pci_read_config_word(dev, dev->pm_cap + PCI_PM_CTRL, &pms); 1170 pms &= ~PCI_PM_CTRL_PME_ENABLE; 1171 pci_write_config_word(dev, dev->pm_cap + PCI_PM_CTRL, pms); 1172 1173 pme_irq = irq_of_parse_and_map(hose->dn, 0); 1174 if (!pme_irq) { 1175 dev_err(&dev->dev, "Failed to map PME interrupt.\n"); 1176 1177 return -ENXIO; 1178 } 1179 1180 res = devm_request_irq(hose->parent, pme_irq, 1181 fsl_pci_pme_handle, 1182 IRQF_SHARED, 1183 "[PCI] PME", hose); 1184 if (res < 0) { 1185 dev_err(&dev->dev, "Unable to request irq %d for PME\n", pme_irq); 1186 irq_dispose_mapping(pme_irq); 1187 1188 return -ENODEV; 1189 } 1190 1191 pci = hose->private_data; 1192 1193 /* Enable PTOD, ENL23D & EXL23D */ 1194 clrbits32(&pci->pex_pme_mes_disr, 1195 PME_DISR_EN_PTOD | PME_DISR_EN_ENL23D | PME_DISR_EN_EXL23D); 1196 1197 out_be32(&pci->pex_pme_mes_ier, 0); 1198 setbits32(&pci->pex_pme_mes_ier, 1199 PME_DISR_EN_PTOD | PME_DISR_EN_ENL23D | PME_DISR_EN_EXL23D); 1200 1201 /* PME Enable */ 1202 pci_read_config_word(dev, dev->pm_cap + PCI_PM_CTRL, &pms); 1203 pms |= PCI_PM_CTRL_PME_ENABLE; 1204 pci_write_config_word(dev, dev->pm_cap + PCI_PM_CTRL, pms); 1205 1206 return 0; 1207 } 1208 1209 static void send_pme_turnoff_message(struct pci_controller *hose) 1210 { 1211 struct ccsr_pci __iomem *pci = hose->private_data; 1212 u32 dr; 1213 int i; 1214 1215 /* Send PME_Turn_Off Message Request */ 1216 setbits32(&pci->pex_pmcr, PEX_PMCR_PTOMR); 1217 1218 /* Wait trun off done */ 1219 for (i = 0; i < 150; i++) { 1220 dr = in_be32(&pci->pex_pme_mes_dr); 1221 if (dr) { 1222 out_be32(&pci->pex_pme_mes_dr, dr); 1223 break; 1224 } 1225 1226 udelay(1000); 1227 } 1228 } 1229 1230 static void fsl_pci_syscore_do_suspend(struct pci_controller *hose) 1231 { 1232 send_pme_turnoff_message(hose); 1233 } 1234 1235 static int fsl_pci_syscore_suspend(void) 1236 { 1237 struct pci_controller *hose, *tmp; 1238 1239 list_for_each_entry_safe(hose, tmp, &hose_list, list_node) 1240 fsl_pci_syscore_do_suspend(hose); 1241 1242 return 0; 1243 } 1244 1245 static void fsl_pci_syscore_do_resume(struct pci_controller *hose) 1246 { 1247 struct ccsr_pci __iomem *pci = hose->private_data; 1248 u32 dr; 1249 int i; 1250 1251 /* Send Exit L2 State Message */ 1252 setbits32(&pci->pex_pmcr, PEX_PMCR_EXL2S); 1253 1254 /* Wait exit done */ 1255 for (i = 0; i < 150; i++) { 1256 dr = in_be32(&pci->pex_pme_mes_dr); 1257 if (dr) { 1258 out_be32(&pci->pex_pme_mes_dr, dr); 1259 break; 1260 } 1261 1262 udelay(1000); 1263 } 1264 1265 setup_pci_atmu(hose); 1266 } 1267 1268 static void fsl_pci_syscore_resume(void) 1269 { 1270 struct pci_controller *hose, *tmp; 1271 1272 list_for_each_entry_safe(hose, tmp, &hose_list, list_node) 1273 fsl_pci_syscore_do_resume(hose); 1274 } 1275 1276 static struct syscore_ops pci_syscore_pm_ops = { 1277 .suspend = fsl_pci_syscore_suspend, 1278 .resume = fsl_pci_syscore_resume, 1279 }; 1280 #endif 1281 1282 void fsl_pcibios_fixup_phb(struct pci_controller *phb) 1283 { 1284 #ifdef CONFIG_PM_SLEEP 1285 fsl_pci_pme_probe(phb); 1286 #endif 1287 } 1288 1289 static int add_err_dev(struct platform_device *pdev) 1290 { 1291 struct platform_device *errdev; 1292 struct mpc85xx_edac_pci_plat_data pd = { 1293 .of_node = pdev->dev.of_node 1294 }; 1295 1296 errdev = platform_device_register_resndata(&pdev->dev, 1297 "mpc85xx-pci-edac", 1298 PLATFORM_DEVID_AUTO, 1299 pdev->resource, 1300 pdev->num_resources, 1301 &pd, sizeof(pd)); 1302 1303 return PTR_ERR_OR_ZERO(errdev); 1304 } 1305 1306 static int fsl_pci_probe(struct platform_device *pdev) 1307 { 1308 struct device_node *node; 1309 int ret; 1310 1311 node = pdev->dev.of_node; 1312 ret = fsl_add_bridge(pdev, fsl_pci_primary == node); 1313 if (ret) 1314 return ret; 1315 1316 ret = add_err_dev(pdev); 1317 if (ret) 1318 dev_err(&pdev->dev, "couldn't register error device: %d\n", 1319 ret); 1320 1321 return 0; 1322 } 1323 1324 static struct platform_driver fsl_pci_driver = { 1325 .driver = { 1326 .name = "fsl-pci", 1327 .of_match_table = pci_ids, 1328 }, 1329 .probe = fsl_pci_probe, 1330 }; 1331 1332 static int __init fsl_pci_init(void) 1333 { 1334 #ifdef CONFIG_PM_SLEEP 1335 register_syscore_ops(&pci_syscore_pm_ops); 1336 #endif 1337 return platform_driver_register(&fsl_pci_driver); 1338 } 1339 arch_initcall(fsl_pci_init); 1340 #endif 1341