1 /* 2 * P1022DS board specific routines 3 * 4 * Authors: Travis Wheatley <travis.wheatley@freescale.com> 5 * Dave Liu <daveliu@freescale.com> 6 * Timur Tabi <timur@freescale.com> 7 * 8 * Copyright 2010 Freescale Semiconductor, Inc. 9 * 10 * This file is taken from the Freescale P1022DS BSP, with modifications: 11 * 2) No AMP support 12 * 3) No PCI endpoint support 13 * 14 * This file is licensed under the terms of the GNU General Public License 15 * version 2. This program is licensed "as is" without any warranty of any 16 * kind, whether express or implied. 17 */ 18 19 #include <linux/pci.h> 20 #include <linux/of_platform.h> 21 #include <asm/div64.h> 22 #include <asm/mpic.h> 23 #include <asm/swiotlb.h> 24 25 #include <sysdev/fsl_soc.h> 26 #include <sysdev/fsl_pci.h> 27 #include <asm/udbg.h> 28 #include <asm/fsl_guts.h> 29 #include <asm/fsl_lbc.h> 30 #include "smp.h" 31 32 #include "mpc85xx.h" 33 34 #if defined(CONFIG_FB_FSL_DIU) || defined(CONFIG_FB_FSL_DIU_MODULE) 35 36 #define PMUXCR_ELBCDIU_MASK 0xc0000000 37 #define PMUXCR_ELBCDIU_NOR16 0x80000000 38 #define PMUXCR_ELBCDIU_DIU 0x40000000 39 40 /* 41 * Board-specific initialization of the DIU. This code should probably be 42 * executed when the DIU is opened, rather than in arch code, but the DIU 43 * driver does not have a mechanism for this (yet). 44 * 45 * This is especially problematic on the P1022DS because the local bus (eLBC) 46 * and the DIU video signals share the same pins, which means that enabling the 47 * DIU will disable access to NOR flash. 48 */ 49 50 /* DIU Pixel Clock bits of the CLKDVDR Global Utilities register */ 51 #define CLKDVDR_PXCKEN 0x80000000 52 #define CLKDVDR_PXCKINV 0x10000000 53 #define CLKDVDR_PXCKDLY 0x06000000 54 #define CLKDVDR_PXCLK_MASK 0x00FF0000 55 56 /* Some ngPIXIS register definitions */ 57 #define PX_CTL 3 58 #define PX_BRDCFG0 8 59 #define PX_BRDCFG1 9 60 61 #define PX_BRDCFG0_ELBC_SPI_MASK 0xc0 62 #define PX_BRDCFG0_ELBC_SPI_ELBC 0x00 63 #define PX_BRDCFG0_ELBC_SPI_NULL 0xc0 64 #define PX_BRDCFG0_ELBC_DIU 0x02 65 66 #define PX_BRDCFG1_DVIEN 0x80 67 #define PX_BRDCFG1_DFPEN 0x40 68 #define PX_BRDCFG1_BACKLIGHT 0x20 69 #define PX_BRDCFG1_DDCEN 0x10 70 71 #define PX_CTL_ALTACC 0x80 72 73 /* 74 * DIU Area Descriptor 75 * 76 * Note that we need to byte-swap the value before it's written to the AD 77 * register. So even though the registers don't look like they're in the same 78 * bit positions as they are on the MPC8610, the same value is written to the 79 * AD register on the MPC8610 and on the P1022. 80 */ 81 #define AD_BYTE_F 0x10000000 82 #define AD_ALPHA_C_MASK 0x0E000000 83 #define AD_ALPHA_C_SHIFT 25 84 #define AD_BLUE_C_MASK 0x01800000 85 #define AD_BLUE_C_SHIFT 23 86 #define AD_GREEN_C_MASK 0x00600000 87 #define AD_GREEN_C_SHIFT 21 88 #define AD_RED_C_MASK 0x00180000 89 #define AD_RED_C_SHIFT 19 90 #define AD_PALETTE 0x00040000 91 #define AD_PIXEL_S_MASK 0x00030000 92 #define AD_PIXEL_S_SHIFT 16 93 #define AD_COMP_3_MASK 0x0000F000 94 #define AD_COMP_3_SHIFT 12 95 #define AD_COMP_2_MASK 0x00000F00 96 #define AD_COMP_2_SHIFT 8 97 #define AD_COMP_1_MASK 0x000000F0 98 #define AD_COMP_1_SHIFT 4 99 #define AD_COMP_0_MASK 0x0000000F 100 #define AD_COMP_0_SHIFT 0 101 102 #define MAKE_AD(alpha, red, blue, green, size, c0, c1, c2, c3) \ 103 cpu_to_le32(AD_BYTE_F | (alpha << AD_ALPHA_C_SHIFT) | \ 104 (blue << AD_BLUE_C_SHIFT) | (green << AD_GREEN_C_SHIFT) | \ 105 (red << AD_RED_C_SHIFT) | (c3 << AD_COMP_3_SHIFT) | \ 106 (c2 << AD_COMP_2_SHIFT) | (c1 << AD_COMP_1_SHIFT) | \ 107 (c0 << AD_COMP_0_SHIFT) | (size << AD_PIXEL_S_SHIFT)) 108 109 struct fsl_law { 110 u32 lawbar; 111 u32 reserved1; 112 u32 lawar; 113 u32 reserved[5]; 114 }; 115 116 #define LAWBAR_MASK 0x00F00000 117 #define LAWBAR_SHIFT 12 118 119 #define LAWAR_EN 0x80000000 120 #define LAWAR_TGT_MASK 0x01F00000 121 #define LAW_TRGT_IF_LBC (0x04 << 20) 122 123 #define LAWAR_MASK (LAWAR_EN | LAWAR_TGT_MASK) 124 #define LAWAR_MATCH (LAWAR_EN | LAW_TRGT_IF_LBC) 125 126 #define BR_BA 0xFFFF8000 127 128 /* 129 * Map a BRx value to a physical address 130 * 131 * The localbus BRx registers only store the lower 32 bits of the address. To 132 * obtain the upper four bits, we need to scan the LAW table. The entry which 133 * maps to the localbus will contain the upper four bits. 134 */ 135 static phys_addr_t lbc_br_to_phys(const void *ecm, unsigned int count, u32 br) 136 { 137 #ifndef CONFIG_PHYS_64BIT 138 /* 139 * If we only have 32-bit addressing, then the BRx address *is* the 140 * physical address. 141 */ 142 return br & BR_BA; 143 #else 144 const struct fsl_law *law = ecm + 0xc08; 145 unsigned int i; 146 147 for (i = 0; i < count; i++) { 148 u64 lawbar = in_be32(&law[i].lawbar); 149 u32 lawar = in_be32(&law[i].lawar); 150 151 if ((lawar & LAWAR_MASK) == LAWAR_MATCH) 152 /* Extract the upper four bits */ 153 return (br & BR_BA) | ((lawbar & LAWBAR_MASK) << 12); 154 } 155 156 return 0; 157 #endif 158 } 159 160 /** 161 * p1022ds_set_monitor_port: switch the output to a different monitor port 162 */ 163 static void p1022ds_set_monitor_port(enum fsl_diu_monitor_port port) 164 { 165 struct device_node *guts_node; 166 struct device_node *lbc_node = NULL; 167 struct device_node *law_node = NULL; 168 struct ccsr_guts __iomem *guts; 169 struct fsl_lbc_regs *lbc = NULL; 170 void *ecm = NULL; 171 u8 __iomem *lbc_lcs0_ba = NULL; 172 u8 __iomem *lbc_lcs1_ba = NULL; 173 phys_addr_t cs0_addr, cs1_addr; 174 u32 br0, or0, br1, or1; 175 const __be32 *iprop; 176 unsigned int num_laws; 177 u8 b; 178 179 /* Map the global utilities registers. */ 180 guts_node = of_find_compatible_node(NULL, NULL, "fsl,p1022-guts"); 181 if (!guts_node) { 182 pr_err("p1022ds: missing global utilities device node\n"); 183 return; 184 } 185 186 guts = of_iomap(guts_node, 0); 187 if (!guts) { 188 pr_err("p1022ds: could not map global utilities device\n"); 189 goto exit; 190 } 191 192 lbc_node = of_find_compatible_node(NULL, NULL, "fsl,p1022-elbc"); 193 if (!lbc_node) { 194 pr_err("p1022ds: missing localbus node\n"); 195 goto exit; 196 } 197 198 lbc = of_iomap(lbc_node, 0); 199 if (!lbc) { 200 pr_err("p1022ds: could not map localbus node\n"); 201 goto exit; 202 } 203 204 law_node = of_find_compatible_node(NULL, NULL, "fsl,ecm-law"); 205 if (!law_node) { 206 pr_err("p1022ds: missing local access window node\n"); 207 goto exit; 208 } 209 210 ecm = of_iomap(law_node, 0); 211 if (!ecm) { 212 pr_err("p1022ds: could not map local access window node\n"); 213 goto exit; 214 } 215 216 iprop = of_get_property(law_node, "fsl,num-laws", NULL); 217 if (!iprop) { 218 pr_err("p1022ds: LAW node is missing fsl,num-laws property\n"); 219 goto exit; 220 } 221 num_laws = be32_to_cpup(iprop); 222 223 /* 224 * Indirect mode requires both BR0 and BR1 to be set to "GPCM", 225 * otherwise writes to these addresses won't actually appear on the 226 * local bus, and so the PIXIS won't see them. 227 * 228 * In FCM mode, writes go to the NAND controller, which does not pass 229 * them to the localbus directly. So we force BR0 and BR1 into GPCM 230 * mode, since we don't care about what's behind the localbus any 231 * more. 232 */ 233 br0 = in_be32(&lbc->bank[0].br); 234 br1 = in_be32(&lbc->bank[1].br); 235 or0 = in_be32(&lbc->bank[0].or); 236 or1 = in_be32(&lbc->bank[1].or); 237 238 /* Make sure CS0 and CS1 are programmed */ 239 if (!(br0 & BR_V) || !(br1 & BR_V)) { 240 pr_err("p1022ds: CS0 and/or CS1 is not programmed\n"); 241 goto exit; 242 } 243 244 /* 245 * Use the existing BRx/ORx values if it's already GPCM. Otherwise, 246 * force the values to simple 32KB GPCM windows with the most 247 * conservative timing. 248 */ 249 if ((br0 & BR_MSEL) != BR_MS_GPCM) { 250 br0 = (br0 & BR_BA) | BR_V; 251 or0 = 0xFFFF8000 | 0xFF7; 252 out_be32(&lbc->bank[0].br, br0); 253 out_be32(&lbc->bank[0].or, or0); 254 } 255 if ((br1 & BR_MSEL) != BR_MS_GPCM) { 256 br1 = (br1 & BR_BA) | BR_V; 257 or1 = 0xFFFF8000 | 0xFF7; 258 out_be32(&lbc->bank[1].br, br1); 259 out_be32(&lbc->bank[1].or, or1); 260 } 261 262 cs0_addr = lbc_br_to_phys(ecm, num_laws, br0); 263 if (!cs0_addr) { 264 pr_err("p1022ds: could not determine physical address for CS0" 265 " (BR0=%08x)\n", br0); 266 goto exit; 267 } 268 cs1_addr = lbc_br_to_phys(ecm, num_laws, br1); 269 if (!cs1_addr) { 270 pr_err("p1022ds: could not determine physical address for CS1" 271 " (BR1=%08x)\n", br1); 272 goto exit; 273 } 274 275 lbc_lcs0_ba = ioremap(cs0_addr, 1); 276 if (!lbc_lcs0_ba) { 277 pr_err("p1022ds: could not ioremap CS0 address %llx\n", 278 (unsigned long long)cs0_addr); 279 goto exit; 280 } 281 lbc_lcs1_ba = ioremap(cs1_addr, 1); 282 if (!lbc_lcs1_ba) { 283 pr_err("p1022ds: could not ioremap CS1 address %llx\n", 284 (unsigned long long)cs1_addr); 285 goto exit; 286 } 287 288 /* Make sure we're in indirect mode first. */ 289 if ((in_be32(&guts->pmuxcr) & PMUXCR_ELBCDIU_MASK) != 290 PMUXCR_ELBCDIU_DIU) { 291 struct device_node *pixis_node; 292 void __iomem *pixis; 293 294 pixis_node = 295 of_find_compatible_node(NULL, NULL, "fsl,p1022ds-fpga"); 296 if (!pixis_node) { 297 pr_err("p1022ds: missing pixis node\n"); 298 goto exit; 299 } 300 301 pixis = of_iomap(pixis_node, 0); 302 of_node_put(pixis_node); 303 if (!pixis) { 304 pr_err("p1022ds: could not map pixis registers\n"); 305 goto exit; 306 } 307 308 /* Enable indirect PIXIS mode. */ 309 setbits8(pixis + PX_CTL, PX_CTL_ALTACC); 310 iounmap(pixis); 311 312 /* Switch the board mux to the DIU */ 313 out_8(lbc_lcs0_ba, PX_BRDCFG0); /* BRDCFG0 */ 314 b = in_8(lbc_lcs1_ba); 315 b |= PX_BRDCFG0_ELBC_DIU; 316 out_8(lbc_lcs1_ba, b); 317 318 /* Set the chip mux to DIU mode. */ 319 clrsetbits_be32(&guts->pmuxcr, PMUXCR_ELBCDIU_MASK, 320 PMUXCR_ELBCDIU_DIU); 321 in_be32(&guts->pmuxcr); 322 } 323 324 325 switch (port) { 326 case FSL_DIU_PORT_DVI: 327 /* Enable the DVI port, disable the DFP and the backlight */ 328 out_8(lbc_lcs0_ba, PX_BRDCFG1); 329 b = in_8(lbc_lcs1_ba); 330 b &= ~(PX_BRDCFG1_DFPEN | PX_BRDCFG1_BACKLIGHT); 331 b |= PX_BRDCFG1_DVIEN; 332 out_8(lbc_lcs1_ba, b); 333 break; 334 case FSL_DIU_PORT_LVDS: 335 /* 336 * LVDS also needs backlight enabled, otherwise the display 337 * will be blank. 338 */ 339 /* Enable the DFP port, disable the DVI and the backlight */ 340 out_8(lbc_lcs0_ba, PX_BRDCFG1); 341 b = in_8(lbc_lcs1_ba); 342 b &= ~PX_BRDCFG1_DVIEN; 343 b |= PX_BRDCFG1_DFPEN | PX_BRDCFG1_BACKLIGHT; 344 out_8(lbc_lcs1_ba, b); 345 break; 346 default: 347 pr_err("p1022ds: unsupported monitor port %i\n", port); 348 } 349 350 exit: 351 if (lbc_lcs1_ba) 352 iounmap(lbc_lcs1_ba); 353 if (lbc_lcs0_ba) 354 iounmap(lbc_lcs0_ba); 355 if (lbc) 356 iounmap(lbc); 357 if (ecm) 358 iounmap(ecm); 359 if (guts) 360 iounmap(guts); 361 362 of_node_put(law_node); 363 of_node_put(lbc_node); 364 of_node_put(guts_node); 365 } 366 367 /** 368 * p1022ds_set_pixel_clock: program the DIU's clock 369 * 370 * @pixclock: the wavelength, in picoseconds, of the clock 371 */ 372 void p1022ds_set_pixel_clock(unsigned int pixclock) 373 { 374 struct device_node *guts_np = NULL; 375 struct ccsr_guts __iomem *guts; 376 unsigned long freq; 377 u64 temp; 378 u32 pxclk; 379 380 /* Map the global utilities registers. */ 381 guts_np = of_find_compatible_node(NULL, NULL, "fsl,p1022-guts"); 382 if (!guts_np) { 383 pr_err("p1022ds: missing global utilities device node\n"); 384 return; 385 } 386 387 guts = of_iomap(guts_np, 0); 388 of_node_put(guts_np); 389 if (!guts) { 390 pr_err("p1022ds: could not map global utilities device\n"); 391 return; 392 } 393 394 /* Convert pixclock from a wavelength to a frequency */ 395 temp = 1000000000000ULL; 396 do_div(temp, pixclock); 397 freq = temp; 398 399 /* 400 * 'pxclk' is the ratio of the platform clock to the pixel clock. 401 * This number is programmed into the CLKDVDR register, and the valid 402 * range of values is 2-255. 403 */ 404 pxclk = DIV_ROUND_CLOSEST(fsl_get_sys_freq(), freq); 405 pxclk = clamp_t(u32, pxclk, 2, 255); 406 407 /* Disable the pixel clock, and set it to non-inverted and no delay */ 408 clrbits32(&guts->clkdvdr, 409 CLKDVDR_PXCKEN | CLKDVDR_PXCKDLY | CLKDVDR_PXCLK_MASK); 410 411 /* Enable the clock and set the pxclk */ 412 setbits32(&guts->clkdvdr, CLKDVDR_PXCKEN | (pxclk << 16)); 413 414 iounmap(guts); 415 } 416 417 /** 418 * p1022ds_valid_monitor_port: set the monitor port for sysfs 419 */ 420 enum fsl_diu_monitor_port 421 p1022ds_valid_monitor_port(enum fsl_diu_monitor_port port) 422 { 423 switch (port) { 424 case FSL_DIU_PORT_DVI: 425 case FSL_DIU_PORT_LVDS: 426 return port; 427 default: 428 return FSL_DIU_PORT_DVI; /* Dual-link LVDS is not supported */ 429 } 430 } 431 432 #endif 433 434 void __init p1022_ds_pic_init(void) 435 { 436 struct mpic *mpic = mpic_alloc(NULL, 0, MPIC_BIG_ENDIAN | 437 MPIC_SINGLE_DEST_CPU, 438 0, 256, " OpenPIC "); 439 BUG_ON(mpic == NULL); 440 mpic_init(mpic); 441 } 442 443 #if defined(CONFIG_FB_FSL_DIU) || defined(CONFIG_FB_FSL_DIU_MODULE) 444 445 /* TRUE if there is a "video=fslfb" command-line parameter. */ 446 static bool fslfb; 447 448 /* 449 * Search for a "video=fslfb" command-line parameter, and set 'fslfb' to 450 * true if we find it. 451 * 452 * We need to use early_param() instead of __setup() because the normal 453 * __setup() gets called to late. However, early_param() gets called very 454 * early, before the device tree is unflattened, so all we can do now is set a 455 * global variable. Later on, p1022_ds_setup_arch() will use that variable 456 * to determine if we need to update the device tree. 457 */ 458 static int __init early_video_setup(char *options) 459 { 460 fslfb = (strncmp(options, "fslfb:", 6) == 0); 461 462 return 0; 463 } 464 early_param("video", early_video_setup); 465 466 #endif 467 468 /* 469 * Setup the architecture 470 */ 471 static void __init p1022_ds_setup_arch(void) 472 { 473 if (ppc_md.progress) 474 ppc_md.progress("p1022_ds_setup_arch()", 0); 475 476 #if defined(CONFIG_FB_FSL_DIU) || defined(CONFIG_FB_FSL_DIU_MODULE) 477 diu_ops.set_monitor_port = p1022ds_set_monitor_port; 478 diu_ops.set_pixel_clock = p1022ds_set_pixel_clock; 479 diu_ops.valid_monitor_port = p1022ds_valid_monitor_port; 480 481 /* 482 * Disable the NOR and NAND flash nodes if there is video=fslfb... 483 * command-line parameter. When the DIU is active, the localbus is 484 * unavailable, so we have to disable these nodes before the MTD 485 * driver loads. 486 */ 487 if (fslfb) { 488 struct device_node *np = 489 of_find_compatible_node(NULL, NULL, "fsl,p1022-elbc"); 490 491 if (np) { 492 struct device_node *np2; 493 494 of_node_get(np); 495 np2 = of_find_compatible_node(np, NULL, "cfi-flash"); 496 if (np2) { 497 static struct property nor_status = { 498 .name = "status", 499 .value = "disabled", 500 .length = sizeof("disabled"), 501 }; 502 503 /* 504 * of_update_property() is called before 505 * kmalloc() is available, so the 'new' object 506 * should be allocated in the global area. 507 * The easiest way is to do that is to 508 * allocate one static local variable for each 509 * call to this function. 510 */ 511 pr_info("p1022ds: disabling %s node", 512 np2->full_name); 513 of_update_property(np2, &nor_status); 514 of_node_put(np2); 515 } 516 517 of_node_get(np); 518 np2 = of_find_compatible_node(np, NULL, 519 "fsl,elbc-fcm-nand"); 520 if (np2) { 521 static struct property nand_status = { 522 .name = "status", 523 .value = "disabled", 524 .length = sizeof("disabled"), 525 }; 526 527 pr_info("p1022ds: disabling %s node", 528 np2->full_name); 529 of_update_property(np2, &nand_status); 530 of_node_put(np2); 531 } 532 533 of_node_put(np); 534 } 535 536 } 537 538 #endif 539 540 mpc85xx_smp_init(); 541 542 fsl_pci_assign_primary(); 543 544 swiotlb_detect_4g(); 545 546 pr_info("Freescale P1022 DS reference board\n"); 547 } 548 549 machine_arch_initcall(p1022_ds, mpc85xx_common_publish_devices); 550 551 machine_arch_initcall(p1022_ds, swiotlb_setup_bus_notifier); 552 553 /* 554 * Called very early, device-tree isn't unflattened 555 */ 556 static int __init p1022_ds_probe(void) 557 { 558 unsigned long root = of_get_flat_dt_root(); 559 560 return of_flat_dt_is_compatible(root, "fsl,p1022ds"); 561 } 562 563 define_machine(p1022_ds) { 564 .name = "P1022 DS", 565 .probe = p1022_ds_probe, 566 .setup_arch = p1022_ds_setup_arch, 567 .init_IRQ = p1022_ds_pic_init, 568 #ifdef CONFIG_PCI 569 .pcibios_fixup_bus = fsl_pcibios_fixup_bus, 570 #endif 571 .get_irq = mpic_get_irq, 572 .restart = fsl_rstcr_restart, 573 .calibrate_decr = generic_calibrate_decr, 574 .progress = udbg_progress, 575 }; 576