1/* 2 * PowerPC version 3 * Copyright (C) 1995-1996 Gary Thomas (gdt@linuxppc.org) 4 * Rewritten by Cort Dougan (cort@cs.nmt.edu) for PReP 5 * Copyright (C) 1996 Cort Dougan <cort@cs.nmt.edu> 6 * Low-level exception handlers and MMU support 7 * rewritten by Paul Mackerras. 8 * Copyright (C) 1996 Paul Mackerras. 9 * MPC8xx modifications by Dan Malek 10 * Copyright (C) 1997 Dan Malek (dmalek@jlc.net). 11 * 12 * This file contains low-level support and setup for PowerPC 8xx 13 * embedded processors, including trap and interrupt dispatch. 14 * 15 * This program is free software; you can redistribute it and/or 16 * modify it under the terms of the GNU General Public License 17 * as published by the Free Software Foundation; either version 18 * 2 of the License, or (at your option) any later version. 19 * 20 */ 21 22#include <linux/init.h> 23#include <asm/processor.h> 24#include <asm/page.h> 25#include <asm/mmu.h> 26#include <asm/cache.h> 27#include <asm/pgtable.h> 28#include <asm/cputable.h> 29#include <asm/thread_info.h> 30#include <asm/ppc_asm.h> 31#include <asm/asm-offsets.h> 32#include <asm/ptrace.h> 33 34/* Macro to make the code more readable. */ 35#ifdef CONFIG_8xx_CPU6 36#define SPRN_MI_TWC_ADDR 0x2b80 37#define SPRN_MI_RPN_ADDR 0x2d80 38#define SPRN_MD_TWC_ADDR 0x3b80 39#define SPRN_MD_RPN_ADDR 0x3d80 40 41#define MTSPR_CPU6(spr, reg, treg) \ 42 li treg, spr##_ADDR; \ 43 stw treg, 12(r0); \ 44 lwz treg, 12(r0); \ 45 mtspr spr, reg 46#else 47#define MTSPR_CPU6(spr, reg, treg) \ 48 mtspr spr, reg 49#endif 50 51/* 52 * Value for the bits that have fixed value in RPN entries. 53 * Also used for tagging DAR for DTLBerror. 54 */ 55#ifdef CONFIG_PPC_16K_PAGES 56#define RPN_PATTERN (0x00f0 | MD_SPS16K) 57#else 58#define RPN_PATTERN 0x00f0 59#endif 60 61 __HEAD 62_ENTRY(_stext); 63_ENTRY(_start); 64 65/* MPC8xx 66 * This port was done on an MBX board with an 860. Right now I only 67 * support an ELF compressed (zImage) boot from EPPC-Bug because the 68 * code there loads up some registers before calling us: 69 * r3: ptr to board info data 70 * r4: initrd_start or if no initrd then 0 71 * r5: initrd_end - unused if r4 is 0 72 * r6: Start of command line string 73 * r7: End of command line string 74 * 75 * I decided to use conditional compilation instead of checking PVR and 76 * adding more processor specific branches around code I don't need. 77 * Since this is an embedded processor, I also appreciate any memory 78 * savings I can get. 79 * 80 * The MPC8xx does not have any BATs, but it supports large page sizes. 81 * We first initialize the MMU to support 8M byte pages, then load one 82 * entry into each of the instruction and data TLBs to map the first 83 * 8M 1:1. I also mapped an additional I/O space 1:1 so we can get to 84 * the "internal" processor registers before MMU_init is called. 85 * 86 * -- Dan 87 */ 88 .globl __start 89__start: 90 mr r31,r3 /* save device tree ptr */ 91 92 /* We have to turn on the MMU right away so we get cache modes 93 * set correctly. 94 */ 95 bl initial_mmu 96 97/* We now have the lower 8 Meg mapped into TLB entries, and the caches 98 * ready to work. 99 */ 100 101turn_on_mmu: 102 mfmsr r0 103 ori r0,r0,MSR_DR|MSR_IR 104 mtspr SPRN_SRR1,r0 105 lis r0,start_here@h 106 ori r0,r0,start_here@l 107 mtspr SPRN_SRR0,r0 108 SYNC 109 rfi /* enables MMU */ 110 111/* 112 * Exception entry code. This code runs with address translation 113 * turned off, i.e. using physical addresses. 114 * We assume sprg3 has the physical address of the current 115 * task's thread_struct. 116 */ 117#define EXCEPTION_PROLOG \ 118 EXCEPTION_PROLOG_0; \ 119 EXCEPTION_PROLOG_1; \ 120 EXCEPTION_PROLOG_2 121 122#define EXCEPTION_PROLOG_0 \ 123 mtspr SPRN_SPRG_SCRATCH0,r10; \ 124 mtspr SPRN_SPRG_SCRATCH1,r11; \ 125 mfcr r10 126 127#define EXCEPTION_PROLOG_1 \ 128 mfspr r11,SPRN_SRR1; /* check whether user or kernel */ \ 129 andi. r11,r11,MSR_PR; \ 130 tophys(r11,r1); /* use tophys(r1) if kernel */ \ 131 beq 1f; \ 132 mfspr r11,SPRN_SPRG_THREAD; \ 133 lwz r11,THREAD_INFO-THREAD(r11); \ 134 addi r11,r11,THREAD_SIZE; \ 135 tophys(r11,r11); \ 1361: subi r11,r11,INT_FRAME_SIZE /* alloc exc. frame */ 137 138 139#define EXCEPTION_PROLOG_2 \ 140 CLR_TOP32(r11); \ 141 stw r10,_CCR(r11); /* save registers */ \ 142 stw r12,GPR12(r11); \ 143 stw r9,GPR9(r11); \ 144 mfspr r10,SPRN_SPRG_SCRATCH0; \ 145 stw r10,GPR10(r11); \ 146 mfspr r12,SPRN_SPRG_SCRATCH1; \ 147 stw r12,GPR11(r11); \ 148 mflr r10; \ 149 stw r10,_LINK(r11); \ 150 mfspr r12,SPRN_SRR0; \ 151 mfspr r9,SPRN_SRR1; \ 152 stw r1,GPR1(r11); \ 153 stw r1,0(r11); \ 154 tovirt(r1,r11); /* set new kernel sp */ \ 155 li r10,MSR_KERNEL & ~(MSR_IR|MSR_DR); /* can take exceptions */ \ 156 MTMSRD(r10); /* (except for mach check in rtas) */ \ 157 stw r0,GPR0(r11); \ 158 SAVE_4GPRS(3, r11); \ 159 SAVE_2GPRS(7, r11) 160 161/* 162 * Exception exit code. 163 */ 164#define EXCEPTION_EPILOG_0 \ 165 mtcr r10; \ 166 mfspr r10,SPRN_SPRG_SCRATCH0; \ 167 mfspr r11,SPRN_SPRG_SCRATCH1 168 169/* 170 * Note: code which follows this uses cr0.eq (set if from kernel), 171 * r11, r12 (SRR0), and r9 (SRR1). 172 * 173 * Note2: once we have set r1 we are in a position to take exceptions 174 * again, and we could thus set MSR:RI at that point. 175 */ 176 177/* 178 * Exception vectors. 179 */ 180#define EXCEPTION(n, label, hdlr, xfer) \ 181 . = n; \ 182label: \ 183 EXCEPTION_PROLOG; \ 184 addi r3,r1,STACK_FRAME_OVERHEAD; \ 185 xfer(n, hdlr) 186 187#define EXC_XFER_TEMPLATE(n, hdlr, trap, copyee, tfer, ret) \ 188 li r10,trap; \ 189 stw r10,_TRAP(r11); \ 190 li r10,MSR_KERNEL; \ 191 copyee(r10, r9); \ 192 bl tfer; \ 193i##n: \ 194 .long hdlr; \ 195 .long ret 196 197#define COPY_EE(d, s) rlwimi d,s,0,16,16 198#define NOCOPY(d, s) 199 200#define EXC_XFER_STD(n, hdlr) \ 201 EXC_XFER_TEMPLATE(n, hdlr, n, NOCOPY, transfer_to_handler_full, \ 202 ret_from_except_full) 203 204#define EXC_XFER_LITE(n, hdlr) \ 205 EXC_XFER_TEMPLATE(n, hdlr, n+1, NOCOPY, transfer_to_handler, \ 206 ret_from_except) 207 208#define EXC_XFER_EE(n, hdlr) \ 209 EXC_XFER_TEMPLATE(n, hdlr, n, COPY_EE, transfer_to_handler_full, \ 210 ret_from_except_full) 211 212#define EXC_XFER_EE_LITE(n, hdlr) \ 213 EXC_XFER_TEMPLATE(n, hdlr, n+1, COPY_EE, transfer_to_handler, \ 214 ret_from_except) 215 216/* System reset */ 217 EXCEPTION(0x100, Reset, unknown_exception, EXC_XFER_STD) 218 219/* Machine check */ 220 . = 0x200 221MachineCheck: 222 EXCEPTION_PROLOG 223 mfspr r4,SPRN_DAR 224 stw r4,_DAR(r11) 225 li r5,RPN_PATTERN 226 mtspr SPRN_DAR,r5 /* Tag DAR, to be used in DTLB Error */ 227 mfspr r5,SPRN_DSISR 228 stw r5,_DSISR(r11) 229 addi r3,r1,STACK_FRAME_OVERHEAD 230 EXC_XFER_STD(0x200, machine_check_exception) 231 232/* Data access exception. 233 * This is "never generated" by the MPC8xx. 234 */ 235 . = 0x300 236DataAccess: 237 238/* Instruction access exception. 239 * This is "never generated" by the MPC8xx. 240 */ 241 . = 0x400 242InstructionAccess: 243 244/* External interrupt */ 245 EXCEPTION(0x500, HardwareInterrupt, do_IRQ, EXC_XFER_LITE) 246 247/* Alignment exception */ 248 . = 0x600 249Alignment: 250 EXCEPTION_PROLOG 251 mfspr r4,SPRN_DAR 252 stw r4,_DAR(r11) 253 li r5,RPN_PATTERN 254 mtspr SPRN_DAR,r5 /* Tag DAR, to be used in DTLB Error */ 255 mfspr r5,SPRN_DSISR 256 stw r5,_DSISR(r11) 257 addi r3,r1,STACK_FRAME_OVERHEAD 258 EXC_XFER_EE(0x600, alignment_exception) 259 260/* Program check exception */ 261 EXCEPTION(0x700, ProgramCheck, program_check_exception, EXC_XFER_STD) 262 263/* No FPU on MPC8xx. This exception is not supposed to happen. 264*/ 265 EXCEPTION(0x800, FPUnavailable, unknown_exception, EXC_XFER_STD) 266 267/* Decrementer */ 268 EXCEPTION(0x900, Decrementer, timer_interrupt, EXC_XFER_LITE) 269 270 EXCEPTION(0xa00, Trap_0a, unknown_exception, EXC_XFER_EE) 271 EXCEPTION(0xb00, Trap_0b, unknown_exception, EXC_XFER_EE) 272 273/* System call */ 274 . = 0xc00 275SystemCall: 276 EXCEPTION_PROLOG 277 EXC_XFER_EE_LITE(0xc00, DoSyscall) 278 279/* Single step - not used on 601 */ 280 EXCEPTION(0xd00, SingleStep, single_step_exception, EXC_XFER_STD) 281 EXCEPTION(0xe00, Trap_0e, unknown_exception, EXC_XFER_EE) 282 EXCEPTION(0xf00, Trap_0f, unknown_exception, EXC_XFER_EE) 283 284/* On the MPC8xx, this is a software emulation interrupt. It occurs 285 * for all unimplemented and illegal instructions. 286 */ 287 EXCEPTION(0x1000, SoftEmu, SoftwareEmulation, EXC_XFER_STD) 288 289 . = 0x1100 290/* 291 * For the MPC8xx, this is a software tablewalk to load the instruction 292 * TLB. The task switch loads the M_TW register with the pointer to the first 293 * level table. 294 * If we discover there is no second level table (value is zero) or if there 295 * is an invalid pte, we load that into the TLB, which causes another fault 296 * into the TLB Error interrupt where we can handle such problems. 297 * We have to use the MD_xxx registers for the tablewalk because the 298 * equivalent MI_xxx registers only perform the attribute functions. 299 */ 300InstructionTLBMiss: 301#ifdef CONFIG_8xx_CPU6 302 mtspr SPRN_DAR, r3 303#endif 304 EXCEPTION_PROLOG_0 305 mtspr SPRN_SPRG_SCRATCH2, r10 306 mfspr r10, SPRN_SRR0 /* Get effective address of fault */ 307#ifdef CONFIG_8xx_CPU15 308 addi r11, r10, PAGE_SIZE 309 tlbie r11 310 addi r11, r10, -PAGE_SIZE 311 tlbie r11 312#endif 313 314 /* If we are faulting a kernel address, we have to use the 315 * kernel page tables. 316 */ 317#ifdef CONFIG_MODULES 318 /* Only modules will cause ITLB Misses as we always 319 * pin the first 8MB of kernel memory */ 320 andis. r11, r10, 0x8000 /* Address >= 0x80000000 */ 321#endif 322 mfspr r11, SPRN_M_TW /* Get level 1 table */ 323#ifdef CONFIG_MODULES 324 beq 3f 325 lis r11, (swapper_pg_dir-PAGE_OFFSET)@ha 3263: 327#endif 328 /* Insert level 1 index */ 329 rlwimi r11, r10, 32 - ((PAGE_SHIFT - 2) << 1), (PAGE_SHIFT - 2) << 1, 29 330 lwz r11, (swapper_pg_dir-PAGE_OFFSET)@l(r11) /* Get the level 1 entry */ 331 332 /* Load the MI_TWC with the attributes for this "segment." */ 333 MTSPR_CPU6(SPRN_MI_TWC, r11, r3) /* Set segment attributes */ 334 rlwinm r11, r11,0,0,19 /* Extract page descriptor page address */ 335 /* Extract level 2 index */ 336 rlwinm r10, r10, 32 - (PAGE_SHIFT - 2), 32 - PAGE_SHIFT, 29 337 lwzx r10, r10, r11 /* Get the pte */ 338 339#ifdef CONFIG_SWAP 340 rlwinm r11, r10, 32-5, _PAGE_PRESENT 341 and r11, r11, r10 342 rlwimi r10, r11, 0, _PAGE_PRESENT 343#endif 344 li r11, RPN_PATTERN 345 /* The Linux PTE won't go exactly into the MMU TLB. 346 * Software indicator bits 21 and 28 must be clear. 347 * Software indicator bits 24, 25, 26, and 27 must be 348 * set. All other Linux PTE bits control the behavior 349 * of the MMU. 350 */ 351 rlwimi r10, r11, 0, 0x07f8 /* Set 24-27, clear 21-23,28 */ 352 MTSPR_CPU6(SPRN_MI_RPN, r10, r3) /* Update TLB entry */ 353 354 /* Restore registers */ 355#ifdef CONFIG_8xx_CPU6 356 mfspr r3, SPRN_DAR 357 mtspr SPRN_DAR, r11 /* Tag DAR */ 358#endif 359 mfspr r10, SPRN_SPRG_SCRATCH2 360 EXCEPTION_EPILOG_0 361 rfi 362 363 . = 0x1200 364DataStoreTLBMiss: 365#ifdef CONFIG_8xx_CPU6 366 mtspr SPRN_DAR, r3 367#endif 368 EXCEPTION_PROLOG_0 369 mtspr SPRN_SPRG_SCRATCH2, r10 370 mfspr r10, SPRN_MD_EPN 371 372 /* If we are faulting a kernel address, we have to use the 373 * kernel page tables. 374 */ 375 andis. r11, r10, 0x8000 376 mfspr r11, SPRN_M_TW /* Get level 1 table */ 377 beq 3f 378 lis r11, (swapper_pg_dir-PAGE_OFFSET)@ha 3793: 380 /* Insert level 1 index */ 381 rlwimi r11, r10, 32 - ((PAGE_SHIFT - 2) << 1), (PAGE_SHIFT - 2) << 1, 29 382 lwz r11, (swapper_pg_dir-PAGE_OFFSET)@l(r11) /* Get the level 1 entry */ 383 384 /* We have a pte table, so load fetch the pte from the table. 385 */ 386 /* Extract level 2 index */ 387 rlwinm r10, r10, 32 - (PAGE_SHIFT - 2), 32 - PAGE_SHIFT, 29 388 rlwimi r10, r11, 0, 0, 32 - PAGE_SHIFT - 1 /* Add level 2 base */ 389 lwz r10, 0(r10) /* Get the pte */ 390 391 /* Insert the Guarded flag into the TWC from the Linux PTE. 392 * It is bit 27 of both the Linux PTE and the TWC (at least 393 * I got that right :-). It will be better when we can put 394 * this into the Linux pgd/pmd and load it in the operation 395 * above. 396 */ 397 rlwimi r11, r10, 0, 27, 27 398 /* Insert the WriteThru flag into the TWC from the Linux PTE. 399 * It is bit 25 in the Linux PTE and bit 30 in the TWC 400 */ 401 rlwimi r11, r10, 32-5, 30, 30 402 MTSPR_CPU6(SPRN_MD_TWC, r11, r3) 403 404 /* Both _PAGE_ACCESSED and _PAGE_PRESENT has to be set. 405 * We also need to know if the insn is a load/store, so: 406 * Clear _PAGE_PRESENT and load that which will 407 * trap into DTLB Error with store bit set accordinly. 408 */ 409 /* PRESENT=0x1, ACCESSED=0x20 410 * r11 = ((r10 & PRESENT) & ((r10 & ACCESSED) >> 5)); 411 * r10 = (r10 & ~PRESENT) | r11; 412 */ 413#ifdef CONFIG_SWAP 414 rlwinm r11, r10, 32-5, _PAGE_PRESENT 415 and r11, r11, r10 416 rlwimi r10, r11, 0, _PAGE_PRESENT 417#endif 418 /* The Linux PTE won't go exactly into the MMU TLB. 419 * Software indicator bits 22 and 28 must be clear. 420 * Software indicator bits 24, 25, 26, and 27 must be 421 * set. All other Linux PTE bits control the behavior 422 * of the MMU. 423 */ 424 li r11, RPN_PATTERN 425 rlwimi r10, r11, 0, 24, 28 /* Set 24-27, clear 28 */ 426 MTSPR_CPU6(SPRN_MD_RPN, r10, r3) /* Update TLB entry */ 427 428 /* Restore registers */ 429#ifdef CONFIG_8xx_CPU6 430 mfspr r3, SPRN_DAR 431#endif 432 mtspr SPRN_DAR, r11 /* Tag DAR */ 433 mfspr r10, SPRN_SPRG_SCRATCH2 434 EXCEPTION_EPILOG_0 435 rfi 436 437/* This is an instruction TLB error on the MPC8xx. This could be due 438 * to many reasons, such as executing guarded memory or illegal instruction 439 * addresses. There is nothing to do but handle a big time error fault. 440 */ 441 . = 0x1300 442InstructionTLBError: 443 EXCEPTION_PROLOG 444 mr r4,r12 445 mr r5,r9 446 andis. r10,r5,0x4000 447 beq+ 1f 448 tlbie r4 449 /* 0x400 is InstructionAccess exception, needed by bad_page_fault() */ 4501: EXC_XFER_LITE(0x400, handle_page_fault) 451 452/* This is the data TLB error on the MPC8xx. This could be due to 453 * many reasons, including a dirty update to a pte. We bail out to 454 * a higher level function that can handle it. 455 */ 456 . = 0x1400 457DataTLBError: 458 EXCEPTION_PROLOG_0 459 460 mfspr r11, SPRN_DAR 461 cmpwi cr0, r11, RPN_PATTERN 462 beq- FixupDAR /* must be a buggy dcbX, icbi insn. */ 463DARFixed:/* Return from dcbx instruction bug workaround */ 464 EXCEPTION_PROLOG_1 465 EXCEPTION_PROLOG_2 466 mfspr r5,SPRN_DSISR 467 stw r5,_DSISR(r11) 468 mfspr r4,SPRN_DAR 469 andis. r10,r5,0x4000 470 beq+ 1f 471 tlbie r4 4721: li r10,RPN_PATTERN 473 mtspr SPRN_DAR,r10 /* Tag DAR, to be used in DTLB Error */ 474 /* 0x300 is DataAccess exception, needed by bad_page_fault() */ 475 EXC_XFER_LITE(0x300, handle_page_fault) 476 477 EXCEPTION(0x1500, Trap_15, unknown_exception, EXC_XFER_EE) 478 EXCEPTION(0x1600, Trap_16, unknown_exception, EXC_XFER_EE) 479 EXCEPTION(0x1700, Trap_17, unknown_exception, EXC_XFER_EE) 480 EXCEPTION(0x1800, Trap_18, unknown_exception, EXC_XFER_EE) 481 EXCEPTION(0x1900, Trap_19, unknown_exception, EXC_XFER_EE) 482 EXCEPTION(0x1a00, Trap_1a, unknown_exception, EXC_XFER_EE) 483 EXCEPTION(0x1b00, Trap_1b, unknown_exception, EXC_XFER_EE) 484 485/* On the MPC8xx, these next four traps are used for development 486 * support of breakpoints and such. Someday I will get around to 487 * using them. 488 */ 489 EXCEPTION(0x1c00, Trap_1c, unknown_exception, EXC_XFER_EE) 490 EXCEPTION(0x1d00, Trap_1d, unknown_exception, EXC_XFER_EE) 491 EXCEPTION(0x1e00, Trap_1e, unknown_exception, EXC_XFER_EE) 492 EXCEPTION(0x1f00, Trap_1f, unknown_exception, EXC_XFER_EE) 493 494 . = 0x2000 495 496/* This is the procedure to calculate the data EA for buggy dcbx,dcbi instructions 497 * by decoding the registers used by the dcbx instruction and adding them. 498 * DAR is set to the calculated address. 499 */ 500 /* define if you don't want to use self modifying code */ 501#define NO_SELF_MODIFYING_CODE 502FixupDAR:/* Entry point for dcbx workaround. */ 503 mtspr SPRN_SPRG_SCRATCH2, r10 504 /* fetch instruction from memory. */ 505 mfspr r10, SPRN_SRR0 506 andis. r11, r10, 0x8000 /* Address >= 0x80000000 */ 507 mfspr r11, SPRN_M_TW /* Get level 1 table */ 508 beq 3f 509 lis r11, (swapper_pg_dir-PAGE_OFFSET)@ha 510 /* Insert level 1 index */ 5113: rlwimi r11, r10, 32 - ((PAGE_SHIFT - 2) << 1), (PAGE_SHIFT - 2) << 1, 29 512 lwz r11, (swapper_pg_dir-PAGE_OFFSET)@l(r11) /* Get the level 1 entry */ 513 rlwinm r11, r11,0,0,19 /* Extract page descriptor page address */ 514 /* Insert level 2 index */ 515 rlwimi r11, r10, 32 - (PAGE_SHIFT - 2), 32 - PAGE_SHIFT, 29 516 lwz r11, 0(r11) /* Get the pte */ 517 /* concat physical page address(r11) and page offset(r10) */ 518 rlwimi r11, r10, 0, 32 - PAGE_SHIFT, 31 519 lwz r11,0(r11) 520/* Check if it really is a dcbx instruction. */ 521/* dcbt and dcbtst does not generate DTLB Misses/Errors, 522 * no need to include them here */ 523 xoris r10, r11, 0x7c00 /* check if major OP code is 31 */ 524 rlwinm r10, r10, 0, 21, 5 525 cmpwi cr0, r10, 2028 /* Is dcbz? */ 526 beq+ 142f 527 cmpwi cr0, r10, 940 /* Is dcbi? */ 528 beq+ 142f 529 cmpwi cr0, r10, 108 /* Is dcbst? */ 530 beq+ 144f /* Fix up store bit! */ 531 cmpwi cr0, r10, 172 /* Is dcbf? */ 532 beq+ 142f 533 cmpwi cr0, r10, 1964 /* Is icbi? */ 534 beq+ 142f 535141: mfspr r10,SPRN_SPRG_SCRATCH2 536 b DARFixed /* Nope, go back to normal TLB processing */ 537 538144: mfspr r10, SPRN_DSISR 539 rlwinm r10, r10,0,7,5 /* Clear store bit for buggy dcbst insn */ 540 mtspr SPRN_DSISR, r10 541142: /* continue, it was a dcbx, dcbi instruction. */ 542#ifndef NO_SELF_MODIFYING_CODE 543 andis. r10,r11,0x1f /* test if reg RA is r0 */ 544 li r10,modified_instr@l 545 dcbtst r0,r10 /* touch for store */ 546 rlwinm r11,r11,0,0,20 /* Zero lower 10 bits */ 547 oris r11,r11,640 /* Transform instr. to a "add r10,RA,RB" */ 548 ori r11,r11,532 549 stw r11,0(r10) /* store add/and instruction */ 550 dcbf 0,r10 /* flush new instr. to memory. */ 551 icbi 0,r10 /* invalidate instr. cache line */ 552 mfspr r11, SPRN_SPRG_SCRATCH1 /* restore r11 */ 553 mfspr r10, SPRN_SPRG_SCRATCH0 /* restore r10 */ 554 isync /* Wait until new instr is loaded from memory */ 555modified_instr: 556 .space 4 /* this is where the add instr. is stored */ 557 bne+ 143f 558 subf r10,r0,r10 /* r10=r10-r0, only if reg RA is r0 */ 559143: mtdar r10 /* store faulting EA in DAR */ 560 mfspr r10,SPRN_SPRG_SCRATCH2 561 b DARFixed /* Go back to normal TLB handling */ 562#else 563 mfctr r10 564 mtdar r10 /* save ctr reg in DAR */ 565 rlwinm r10, r11, 24, 24, 28 /* offset into jump table for reg RB */ 566 addi r10, r10, 150f@l /* add start of table */ 567 mtctr r10 /* load ctr with jump address */ 568 xor r10, r10, r10 /* sum starts at zero */ 569 bctr /* jump into table */ 570150: 571 add r10, r10, r0 ;b 151f 572 add r10, r10, r1 ;b 151f 573 add r10, r10, r2 ;b 151f 574 add r10, r10, r3 ;b 151f 575 add r10, r10, r4 ;b 151f 576 add r10, r10, r5 ;b 151f 577 add r10, r10, r6 ;b 151f 578 add r10, r10, r7 ;b 151f 579 add r10, r10, r8 ;b 151f 580 add r10, r10, r9 ;b 151f 581 mtctr r11 ;b 154f /* r10 needs special handling */ 582 mtctr r11 ;b 153f /* r11 needs special handling */ 583 add r10, r10, r12 ;b 151f 584 add r10, r10, r13 ;b 151f 585 add r10, r10, r14 ;b 151f 586 add r10, r10, r15 ;b 151f 587 add r10, r10, r16 ;b 151f 588 add r10, r10, r17 ;b 151f 589 add r10, r10, r18 ;b 151f 590 add r10, r10, r19 ;b 151f 591 add r10, r10, r20 ;b 151f 592 add r10, r10, r21 ;b 151f 593 add r10, r10, r22 ;b 151f 594 add r10, r10, r23 ;b 151f 595 add r10, r10, r24 ;b 151f 596 add r10, r10, r25 ;b 151f 597 add r10, r10, r26 ;b 151f 598 add r10, r10, r27 ;b 151f 599 add r10, r10, r28 ;b 151f 600 add r10, r10, r29 ;b 151f 601 add r10, r10, r30 ;b 151f 602 add r10, r10, r31 603151: 604 rlwinm. r11,r11,19,24,28 /* offset into jump table for reg RA */ 605 beq 152f /* if reg RA is zero, don't add it */ 606 addi r11, r11, 150b@l /* add start of table */ 607 mtctr r11 /* load ctr with jump address */ 608 rlwinm r11,r11,0,16,10 /* make sure we don't execute this more than once */ 609 bctr /* jump into table */ 610152: 611 mfdar r11 612 mtctr r11 /* restore ctr reg from DAR */ 613 mtdar r10 /* save fault EA to DAR */ 614 mfspr r10,SPRN_SPRG_SCRATCH2 615 b DARFixed /* Go back to normal TLB handling */ 616 617 /* special handling for r10,r11 since these are modified already */ 618153: mfspr r11, SPRN_SPRG_SCRATCH1 /* load r11 from SPRN_SPRG_SCRATCH1 */ 619 add r10, r10, r11 /* add it */ 620 mfctr r11 /* restore r11 */ 621 b 151b 622154: mfspr r11, SPRN_SPRG_SCRATCH0 /* load r10 from SPRN_SPRG_SCRATCH0 */ 623 add r10, r10, r11 /* add it */ 624 mfctr r11 /* restore r11 */ 625 b 151b 626#endif 627 628/* 629 * This is where the main kernel code starts. 630 */ 631start_here: 632 /* ptr to current */ 633 lis r2,init_task@h 634 ori r2,r2,init_task@l 635 636 /* ptr to phys current thread */ 637 tophys(r4,r2) 638 addi r4,r4,THREAD /* init task's THREAD */ 639 mtspr SPRN_SPRG_THREAD,r4 640 641 /* stack */ 642 lis r1,init_thread_union@ha 643 addi r1,r1,init_thread_union@l 644 li r0,0 645 stwu r0,THREAD_SIZE-STACK_FRAME_OVERHEAD(r1) 646 647 bl early_init /* We have to do this with MMU on */ 648 649/* 650 * Decide what sort of machine this is and initialize the MMU. 651 */ 652 li r3,0 653 mr r4,r31 654 bl machine_init 655 bl MMU_init 656 657/* 658 * Go back to running unmapped so we can load up new values 659 * and change to using our exception vectors. 660 * On the 8xx, all we have to do is invalidate the TLB to clear 661 * the old 8M byte TLB mappings and load the page table base register. 662 */ 663 /* The right way to do this would be to track it down through 664 * init's THREAD like the context switch code does, but this is 665 * easier......until someone changes init's static structures. 666 */ 667 lis r6, swapper_pg_dir@ha 668 tophys(r6,r6) 669#ifdef CONFIG_8xx_CPU6 670 lis r4, cpu6_errata_word@h 671 ori r4, r4, cpu6_errata_word@l 672 li r3, 0x3f80 673 stw r3, 12(r4) 674 lwz r3, 12(r4) 675#endif 676 mtspr SPRN_M_TW, r6 677 lis r4,2f@h 678 ori r4,r4,2f@l 679 tophys(r4,r4) 680 li r3,MSR_KERNEL & ~(MSR_IR|MSR_DR) 681 mtspr SPRN_SRR0,r4 682 mtspr SPRN_SRR1,r3 683 rfi 684/* Load up the kernel context */ 6852: 686 SYNC /* Force all PTE updates to finish */ 687 tlbia /* Clear all TLB entries */ 688 sync /* wait for tlbia/tlbie to finish */ 689 TLBSYNC /* ... on all CPUs */ 690 691 /* set up the PTE pointers for the Abatron bdiGDB. 692 */ 693 tovirt(r6,r6) 694 lis r5, abatron_pteptrs@h 695 ori r5, r5, abatron_pteptrs@l 696 stw r5, 0xf0(r0) /* Must match your Abatron config file */ 697 tophys(r5,r5) 698 stw r6, 0(r5) 699 700/* Now turn on the MMU for real! */ 701 li r4,MSR_KERNEL 702 lis r3,start_kernel@h 703 ori r3,r3,start_kernel@l 704 mtspr SPRN_SRR0,r3 705 mtspr SPRN_SRR1,r4 706 rfi /* enable MMU and jump to start_kernel */ 707 708/* Set up the initial MMU state so we can do the first level of 709 * kernel initialization. This maps the first 8 MBytes of memory 1:1 710 * virtual to physical. Also, set the cache mode since that is defined 711 * by TLB entries and perform any additional mapping (like of the IMMR). 712 * If configured to pin some TLBs, we pin the first 8 Mbytes of kernel, 713 * 24 Mbytes of data, and the 8M IMMR space. Anything not covered by 714 * these mappings is mapped by page tables. 715 */ 716initial_mmu: 717 tlbia /* Invalidate all TLB entries */ 718/* Always pin the first 8 MB ITLB to prevent ITLB 719 misses while mucking around with SRR0/SRR1 in asm 720*/ 721 lis r8, MI_RSV4I@h 722 ori r8, r8, 0x1c00 723 724 mtspr SPRN_MI_CTR, r8 /* Set instruction MMU control */ 725 726#ifdef CONFIG_PIN_TLB 727 lis r10, (MD_RSV4I | MD_RESETVAL)@h 728 ori r10, r10, 0x1c00 729 mr r8, r10 730#else 731 lis r10, MD_RESETVAL@h 732#endif 733#ifndef CONFIG_8xx_COPYBACK 734 oris r10, r10, MD_WTDEF@h 735#endif 736 mtspr SPRN_MD_CTR, r10 /* Set data TLB control */ 737 738 /* Now map the lower 8 Meg into the TLBs. For this quick hack, 739 * we can load the instruction and data TLB registers with the 740 * same values. 741 */ 742 lis r8, KERNELBASE@h /* Create vaddr for TLB */ 743 ori r8, r8, MI_EVALID /* Mark it valid */ 744 mtspr SPRN_MI_EPN, r8 745 mtspr SPRN_MD_EPN, r8 746 li r8, MI_PS8MEG /* Set 8M byte page */ 747 ori r8, r8, MI_SVALID /* Make it valid */ 748 mtspr SPRN_MI_TWC, r8 749 mtspr SPRN_MD_TWC, r8 750 li r8, MI_BOOTINIT /* Create RPN for address 0 */ 751 mtspr SPRN_MI_RPN, r8 /* Store TLB entry */ 752 mtspr SPRN_MD_RPN, r8 753 lis r8, MI_Kp@h /* Set the protection mode */ 754 mtspr SPRN_MI_AP, r8 755 mtspr SPRN_MD_AP, r8 756 757 /* Map another 8 MByte at the IMMR to get the processor 758 * internal registers (among other things). 759 */ 760#ifdef CONFIG_PIN_TLB 761 addi r10, r10, 0x0100 762 mtspr SPRN_MD_CTR, r10 763#endif 764 mfspr r9, 638 /* Get current IMMR */ 765 andis. r9, r9, 0xff80 /* Get 8Mbyte boundary */ 766 767 mr r8, r9 /* Create vaddr for TLB */ 768 ori r8, r8, MD_EVALID /* Mark it valid */ 769 mtspr SPRN_MD_EPN, r8 770 li r8, MD_PS8MEG /* Set 8M byte page */ 771 ori r8, r8, MD_SVALID /* Make it valid */ 772 mtspr SPRN_MD_TWC, r8 773 mr r8, r9 /* Create paddr for TLB */ 774 ori r8, r8, MI_BOOTINIT|0x2 /* Inhibit cache -- Cort */ 775 mtspr SPRN_MD_RPN, r8 776 777#ifdef CONFIG_PIN_TLB 778 /* Map two more 8M kernel data pages. 779 */ 780 addi r10, r10, 0x0100 781 mtspr SPRN_MD_CTR, r10 782 783 lis r8, KERNELBASE@h /* Create vaddr for TLB */ 784 addis r8, r8, 0x0080 /* Add 8M */ 785 ori r8, r8, MI_EVALID /* Mark it valid */ 786 mtspr SPRN_MD_EPN, r8 787 li r9, MI_PS8MEG /* Set 8M byte page */ 788 ori r9, r9, MI_SVALID /* Make it valid */ 789 mtspr SPRN_MD_TWC, r9 790 li r11, MI_BOOTINIT /* Create RPN for address 0 */ 791 addis r11, r11, 0x0080 /* Add 8M */ 792 mtspr SPRN_MD_RPN, r11 793 794 addi r10, r10, 0x0100 795 mtspr SPRN_MD_CTR, r10 796 797 addis r8, r8, 0x0080 /* Add 8M */ 798 mtspr SPRN_MD_EPN, r8 799 mtspr SPRN_MD_TWC, r9 800 addis r11, r11, 0x0080 /* Add 8M */ 801 mtspr SPRN_MD_RPN, r11 802#endif 803 804 /* Since the cache is enabled according to the information we 805 * just loaded into the TLB, invalidate and enable the caches here. 806 * We should probably check/set other modes....later. 807 */ 808 lis r8, IDC_INVALL@h 809 mtspr SPRN_IC_CST, r8 810 mtspr SPRN_DC_CST, r8 811 lis r8, IDC_ENABLE@h 812 mtspr SPRN_IC_CST, r8 813#ifdef CONFIG_8xx_COPYBACK 814 mtspr SPRN_DC_CST, r8 815#else 816 /* For a debug option, I left this here to easily enable 817 * the write through cache mode 818 */ 819 lis r8, DC_SFWT@h 820 mtspr SPRN_DC_CST, r8 821 lis r8, IDC_ENABLE@h 822 mtspr SPRN_DC_CST, r8 823#endif 824 blr 825 826 827/* 828 * Set up to use a given MMU context. 829 * r3 is context number, r4 is PGD pointer. 830 * 831 * We place the physical address of the new task page directory loaded 832 * into the MMU base register, and set the ASID compare register with 833 * the new "context." 834 */ 835_GLOBAL(set_context) 836 837#ifdef CONFIG_BDI_SWITCH 838 /* Context switch the PTE pointer for the Abatron BDI2000. 839 * The PGDIR is passed as second argument. 840 */ 841 lis r5, KERNELBASE@h 842 lwz r5, 0xf0(r5) 843 stw r4, 0x4(r5) 844#endif 845 846 /* Register M_TW will contain base address of level 1 table minus the 847 * lower part of the kernel PGDIR base address, so that all accesses to 848 * level 1 table are done relative to lower part of kernel PGDIR base 849 * address. 850 */ 851 li r5, (swapper_pg_dir-PAGE_OFFSET)@l 852 sub r4, r4, r5 853 tophys (r4, r4) 854#ifdef CONFIG_8xx_CPU6 855 lis r6, cpu6_errata_word@h 856 ori r6, r6, cpu6_errata_word@l 857 li r7, 0x3f80 858 stw r7, 12(r6) 859 lwz r7, 12(r6) 860#endif 861 mtspr SPRN_M_TW, r4 /* Update pointeur to level 1 table */ 862#ifdef CONFIG_8xx_CPU6 863 li r7, 0x3380 864 stw r7, 12(r6) 865 lwz r7, 12(r6) 866#endif 867 mtspr SPRN_M_CASID, r3 /* Update context */ 868 SYNC 869 blr 870 871#ifdef CONFIG_8xx_CPU6 872/* It's here because it is unique to the 8xx. 873 * It is important we get called with interrupts disabled. I used to 874 * do that, but it appears that all code that calls this already had 875 * interrupt disabled. 876 */ 877 .globl set_dec_cpu6 878set_dec_cpu6: 879 lis r7, cpu6_errata_word@h 880 ori r7, r7, cpu6_errata_word@l 881 li r4, 0x2c00 882 stw r4, 8(r7) 883 lwz r4, 8(r7) 884 mtspr 22, r3 /* Update Decrementer */ 885 SYNC 886 blr 887#endif 888 889/* 890 * We put a few things here that have to be page-aligned. 891 * This stuff goes at the beginning of the data segment, 892 * which is page-aligned. 893 */ 894 .data 895 .globl sdata 896sdata: 897 .globl empty_zero_page 898 .align PAGE_SHIFT 899empty_zero_page: 900 .space PAGE_SIZE 901 902 .globl swapper_pg_dir 903swapper_pg_dir: 904 .space PGD_TABLE_SIZE 905 906/* Room for two PTE table poiners, usually the kernel and current user 907 * pointer to their respective root page table (pgdir). 908 */ 909abatron_pteptrs: 910 .space 8 911 912#ifdef CONFIG_8xx_CPU6 913 .globl cpu6_errata_word 914cpu6_errata_word: 915 .space 16 916#endif 917 918