1 // SPDX-License-Identifier: GPL-2.0-or-later 2 /* 3 * Copyright IBM Corporation 2001, 2005, 2006 4 * Copyright Dave Engebretsen & Todd Inglett 2001 5 * Copyright Linas Vepstas 2005, 2006 6 * Copyright 2001-2012 IBM Corporation. 7 * 8 * Please address comments and feedback to Linas Vepstas <linas@austin.ibm.com> 9 */ 10 11 #include <linux/delay.h> 12 #include <linux/sched.h> 13 #include <linux/init.h> 14 #include <linux/list.h> 15 #include <linux/pci.h> 16 #include <linux/iommu.h> 17 #include <linux/proc_fs.h> 18 #include <linux/rbtree.h> 19 #include <linux/reboot.h> 20 #include <linux/seq_file.h> 21 #include <linux/spinlock.h> 22 #include <linux/export.h> 23 #include <linux/of.h> 24 #include <linux/debugfs.h> 25 26 #include <linux/atomic.h> 27 #include <asm/eeh.h> 28 #include <asm/eeh_event.h> 29 #include <asm/io.h> 30 #include <asm/iommu.h> 31 #include <asm/machdep.h> 32 #include <asm/ppc-pci.h> 33 #include <asm/rtas.h> 34 #include <asm/pte-walk.h> 35 36 37 /** Overview: 38 * EEH, or "Enhanced Error Handling" is a PCI bridge technology for 39 * dealing with PCI bus errors that can't be dealt with within the 40 * usual PCI framework, except by check-stopping the CPU. Systems 41 * that are designed for high-availability/reliability cannot afford 42 * to crash due to a "mere" PCI error, thus the need for EEH. 43 * An EEH-capable bridge operates by converting a detected error 44 * into a "slot freeze", taking the PCI adapter off-line, making 45 * the slot behave, from the OS'es point of view, as if the slot 46 * were "empty": all reads return 0xff's and all writes are silently 47 * ignored. EEH slot isolation events can be triggered by parity 48 * errors on the address or data busses (e.g. during posted writes), 49 * which in turn might be caused by low voltage on the bus, dust, 50 * vibration, humidity, radioactivity or plain-old failed hardware. 51 * 52 * Note, however, that one of the leading causes of EEH slot 53 * freeze events are buggy device drivers, buggy device microcode, 54 * or buggy device hardware. This is because any attempt by the 55 * device to bus-master data to a memory address that is not 56 * assigned to the device will trigger a slot freeze. (The idea 57 * is to prevent devices-gone-wild from corrupting system memory). 58 * Buggy hardware/drivers will have a miserable time co-existing 59 * with EEH. 60 * 61 * Ideally, a PCI device driver, when suspecting that an isolation 62 * event has occurred (e.g. by reading 0xff's), will then ask EEH 63 * whether this is the case, and then take appropriate steps to 64 * reset the PCI slot, the PCI device, and then resume operations. 65 * However, until that day, the checking is done here, with the 66 * eeh_check_failure() routine embedded in the MMIO macros. If 67 * the slot is found to be isolated, an "EEH Event" is synthesized 68 * and sent out for processing. 69 */ 70 71 /* If a device driver keeps reading an MMIO register in an interrupt 72 * handler after a slot isolation event, it might be broken. 73 * This sets the threshold for how many read attempts we allow 74 * before printing an error message. 75 */ 76 #define EEH_MAX_FAILS 2100000 77 78 /* Time to wait for a PCI slot to report status, in milliseconds */ 79 #define PCI_BUS_RESET_WAIT_MSEC (5*60*1000) 80 81 /* 82 * EEH probe mode support, which is part of the flags, 83 * is to support multiple platforms for EEH. Some platforms 84 * like pSeries do PCI emunation based on device tree. 85 * However, other platforms like powernv probe PCI devices 86 * from hardware. The flag is used to distinguish that. 87 * In addition, struct eeh_ops::probe would be invoked for 88 * particular OF node or PCI device so that the corresponding 89 * PE would be created there. 90 */ 91 int eeh_subsystem_flags; 92 EXPORT_SYMBOL(eeh_subsystem_flags); 93 94 /* 95 * EEH allowed maximal frozen times. If one particular PE's 96 * frozen count in last hour exceeds this limit, the PE will 97 * be forced to be offline permanently. 98 */ 99 u32 eeh_max_freezes = 5; 100 101 /* 102 * Controls whether a recovery event should be scheduled when an 103 * isolated device is discovered. This is only really useful for 104 * debugging problems with the EEH core. 105 */ 106 bool eeh_debugfs_no_recover; 107 108 /* Platform dependent EEH operations */ 109 struct eeh_ops *eeh_ops = NULL; 110 111 /* Lock to avoid races due to multiple reports of an error */ 112 DEFINE_RAW_SPINLOCK(confirm_error_lock); 113 EXPORT_SYMBOL_GPL(confirm_error_lock); 114 115 /* Lock to protect passed flags */ 116 static DEFINE_MUTEX(eeh_dev_mutex); 117 118 /* Buffer for reporting pci register dumps. Its here in BSS, and 119 * not dynamically alloced, so that it ends up in RMO where RTAS 120 * can access it. 121 */ 122 #define EEH_PCI_REGS_LOG_LEN 8192 123 static unsigned char pci_regs_buf[EEH_PCI_REGS_LOG_LEN]; 124 125 /* 126 * The struct is used to maintain the EEH global statistic 127 * information. Besides, the EEH global statistics will be 128 * exported to user space through procfs 129 */ 130 struct eeh_stats { 131 u64 no_device; /* PCI device not found */ 132 u64 no_dn; /* OF node not found */ 133 u64 no_cfg_addr; /* Config address not found */ 134 u64 ignored_check; /* EEH check skipped */ 135 u64 total_mmio_ffs; /* Total EEH checks */ 136 u64 false_positives; /* Unnecessary EEH checks */ 137 u64 slot_resets; /* PE reset */ 138 }; 139 140 static struct eeh_stats eeh_stats; 141 142 static int __init eeh_setup(char *str) 143 { 144 if (!strcmp(str, "off")) 145 eeh_add_flag(EEH_FORCE_DISABLED); 146 else if (!strcmp(str, "early_log")) 147 eeh_add_flag(EEH_EARLY_DUMP_LOG); 148 149 return 1; 150 } 151 __setup("eeh=", eeh_setup); 152 153 void eeh_show_enabled(void) 154 { 155 if (eeh_has_flag(EEH_FORCE_DISABLED)) 156 pr_info("EEH: Recovery disabled by kernel parameter.\n"); 157 else if (eeh_has_flag(EEH_ENABLED)) 158 pr_info("EEH: Capable adapter found: recovery enabled.\n"); 159 else 160 pr_info("EEH: No capable adapters found: recovery disabled.\n"); 161 } 162 163 /* 164 * This routine captures assorted PCI configuration space data 165 * for the indicated PCI device, and puts them into a buffer 166 * for RTAS error logging. 167 */ 168 static size_t eeh_dump_dev_log(struct eeh_dev *edev, char *buf, size_t len) 169 { 170 u32 cfg; 171 int cap, i; 172 int n = 0, l = 0; 173 char buffer[128]; 174 175 n += scnprintf(buf+n, len-n, "%04x:%02x:%02x.%01x\n", 176 edev->pe->phb->global_number, edev->bdfn >> 8, 177 PCI_SLOT(edev->bdfn), PCI_FUNC(edev->bdfn)); 178 pr_warn("EEH: of node=%04x:%02x:%02x.%01x\n", 179 edev->pe->phb->global_number, edev->bdfn >> 8, 180 PCI_SLOT(edev->bdfn), PCI_FUNC(edev->bdfn)); 181 182 eeh_ops->read_config(edev, PCI_VENDOR_ID, 4, &cfg); 183 n += scnprintf(buf+n, len-n, "dev/vend:%08x\n", cfg); 184 pr_warn("EEH: PCI device/vendor: %08x\n", cfg); 185 186 eeh_ops->read_config(edev, PCI_COMMAND, 4, &cfg); 187 n += scnprintf(buf+n, len-n, "cmd/stat:%x\n", cfg); 188 pr_warn("EEH: PCI cmd/status register: %08x\n", cfg); 189 190 /* Gather bridge-specific registers */ 191 if (edev->mode & EEH_DEV_BRIDGE) { 192 eeh_ops->read_config(edev, PCI_SEC_STATUS, 2, &cfg); 193 n += scnprintf(buf+n, len-n, "sec stat:%x\n", cfg); 194 pr_warn("EEH: Bridge secondary status: %04x\n", cfg); 195 196 eeh_ops->read_config(edev, PCI_BRIDGE_CONTROL, 2, &cfg); 197 n += scnprintf(buf+n, len-n, "brdg ctl:%x\n", cfg); 198 pr_warn("EEH: Bridge control: %04x\n", cfg); 199 } 200 201 /* Dump out the PCI-X command and status regs */ 202 cap = edev->pcix_cap; 203 if (cap) { 204 eeh_ops->read_config(edev, cap, 4, &cfg); 205 n += scnprintf(buf+n, len-n, "pcix-cmd:%x\n", cfg); 206 pr_warn("EEH: PCI-X cmd: %08x\n", cfg); 207 208 eeh_ops->read_config(edev, cap+4, 4, &cfg); 209 n += scnprintf(buf+n, len-n, "pcix-stat:%x\n", cfg); 210 pr_warn("EEH: PCI-X status: %08x\n", cfg); 211 } 212 213 /* If PCI-E capable, dump PCI-E cap 10 */ 214 cap = edev->pcie_cap; 215 if (cap) { 216 n += scnprintf(buf+n, len-n, "pci-e cap10:\n"); 217 pr_warn("EEH: PCI-E capabilities and status follow:\n"); 218 219 for (i=0; i<=8; i++) { 220 eeh_ops->read_config(edev, cap+4*i, 4, &cfg); 221 n += scnprintf(buf+n, len-n, "%02x:%x\n", 4*i, cfg); 222 223 if ((i % 4) == 0) { 224 if (i != 0) 225 pr_warn("%s\n", buffer); 226 227 l = scnprintf(buffer, sizeof(buffer), 228 "EEH: PCI-E %02x: %08x ", 229 4*i, cfg); 230 } else { 231 l += scnprintf(buffer+l, sizeof(buffer)-l, 232 "%08x ", cfg); 233 } 234 235 } 236 237 pr_warn("%s\n", buffer); 238 } 239 240 /* If AER capable, dump it */ 241 cap = edev->aer_cap; 242 if (cap) { 243 n += scnprintf(buf+n, len-n, "pci-e AER:\n"); 244 pr_warn("EEH: PCI-E AER capability register set follows:\n"); 245 246 for (i=0; i<=13; i++) { 247 eeh_ops->read_config(edev, cap+4*i, 4, &cfg); 248 n += scnprintf(buf+n, len-n, "%02x:%x\n", 4*i, cfg); 249 250 if ((i % 4) == 0) { 251 if (i != 0) 252 pr_warn("%s\n", buffer); 253 254 l = scnprintf(buffer, sizeof(buffer), 255 "EEH: PCI-E AER %02x: %08x ", 256 4*i, cfg); 257 } else { 258 l += scnprintf(buffer+l, sizeof(buffer)-l, 259 "%08x ", cfg); 260 } 261 } 262 263 pr_warn("%s\n", buffer); 264 } 265 266 return n; 267 } 268 269 static void *eeh_dump_pe_log(struct eeh_pe *pe, void *flag) 270 { 271 struct eeh_dev *edev, *tmp; 272 size_t *plen = flag; 273 274 eeh_pe_for_each_dev(pe, edev, tmp) 275 *plen += eeh_dump_dev_log(edev, pci_regs_buf + *plen, 276 EEH_PCI_REGS_LOG_LEN - *plen); 277 278 return NULL; 279 } 280 281 /** 282 * eeh_slot_error_detail - Generate combined log including driver log and error log 283 * @pe: EEH PE 284 * @severity: temporary or permanent error log 285 * 286 * This routine should be called to generate the combined log, which 287 * is comprised of driver log and error log. The driver log is figured 288 * out from the config space of the corresponding PCI device, while 289 * the error log is fetched through platform dependent function call. 290 */ 291 void eeh_slot_error_detail(struct eeh_pe *pe, int severity) 292 { 293 size_t loglen = 0; 294 295 /* 296 * When the PHB is fenced or dead, it's pointless to collect 297 * the data from PCI config space because it should return 298 * 0xFF's. For ER, we still retrieve the data from the PCI 299 * config space. 300 * 301 * For pHyp, we have to enable IO for log retrieval. Otherwise, 302 * 0xFF's is always returned from PCI config space. 303 * 304 * When the @severity is EEH_LOG_PERM, the PE is going to be 305 * removed. Prior to that, the drivers for devices included in 306 * the PE will be closed. The drivers rely on working IO path 307 * to bring the devices to quiet state. Otherwise, PCI traffic 308 * from those devices after they are removed is like to cause 309 * another unexpected EEH error. 310 */ 311 if (!(pe->type & EEH_PE_PHB)) { 312 if (eeh_has_flag(EEH_ENABLE_IO_FOR_LOG) || 313 severity == EEH_LOG_PERM) 314 eeh_pci_enable(pe, EEH_OPT_THAW_MMIO); 315 316 /* 317 * The config space of some PCI devices can't be accessed 318 * when their PEs are in frozen state. Otherwise, fenced 319 * PHB might be seen. Those PEs are identified with flag 320 * EEH_PE_CFG_RESTRICTED, indicating EEH_PE_CFG_BLOCKED 321 * is set automatically when the PE is put to EEH_PE_ISOLATED. 322 * 323 * Restoring BARs possibly triggers PCI config access in 324 * (OPAL) firmware and then causes fenced PHB. If the 325 * PCI config is blocked with flag EEH_PE_CFG_BLOCKED, it's 326 * pointless to restore BARs and dump config space. 327 */ 328 eeh_ops->configure_bridge(pe); 329 if (!(pe->state & EEH_PE_CFG_BLOCKED)) { 330 eeh_pe_restore_bars(pe); 331 332 pci_regs_buf[0] = 0; 333 eeh_pe_traverse(pe, eeh_dump_pe_log, &loglen); 334 } 335 } 336 337 eeh_ops->get_log(pe, severity, pci_regs_buf, loglen); 338 } 339 340 /** 341 * eeh_token_to_phys - Convert EEH address token to phys address 342 * @token: I/O token, should be address in the form 0xA.... 343 * 344 * This routine should be called to convert virtual I/O address 345 * to physical one. 346 */ 347 static inline unsigned long eeh_token_to_phys(unsigned long token) 348 { 349 return ppc_find_vmap_phys(token); 350 } 351 352 /* 353 * On PowerNV platform, we might already have fenced PHB there. 354 * For that case, it's meaningless to recover frozen PE. Intead, 355 * We have to handle fenced PHB firstly. 356 */ 357 static int eeh_phb_check_failure(struct eeh_pe *pe) 358 { 359 struct eeh_pe *phb_pe; 360 unsigned long flags; 361 int ret; 362 363 if (!eeh_has_flag(EEH_PROBE_MODE_DEV)) 364 return -EPERM; 365 366 /* Find the PHB PE */ 367 phb_pe = eeh_phb_pe_get(pe->phb); 368 if (!phb_pe) { 369 pr_warn("%s Can't find PE for PHB#%x\n", 370 __func__, pe->phb->global_number); 371 return -EEXIST; 372 } 373 374 /* If the PHB has been in problematic state */ 375 eeh_serialize_lock(&flags); 376 if (phb_pe->state & EEH_PE_ISOLATED) { 377 ret = 0; 378 goto out; 379 } 380 381 /* Check PHB state */ 382 ret = eeh_ops->get_state(phb_pe, NULL); 383 if ((ret < 0) || 384 (ret == EEH_STATE_NOT_SUPPORT) || eeh_state_active(ret)) { 385 ret = 0; 386 goto out; 387 } 388 389 /* Isolate the PHB and send event */ 390 eeh_pe_mark_isolated(phb_pe); 391 eeh_serialize_unlock(flags); 392 393 pr_debug("EEH: PHB#%x failure detected, location: %s\n", 394 phb_pe->phb->global_number, eeh_pe_loc_get(phb_pe)); 395 eeh_send_failure_event(phb_pe); 396 return 1; 397 out: 398 eeh_serialize_unlock(flags); 399 return ret; 400 } 401 402 static inline const char *eeh_driver_name(struct pci_dev *pdev) 403 { 404 if (pdev) 405 return dev_driver_string(&pdev->dev); 406 407 return "<null>"; 408 } 409 410 /** 411 * eeh_dev_check_failure - Check if all 1's data is due to EEH slot freeze 412 * @edev: eeh device 413 * 414 * Check for an EEH failure for the given device node. Call this 415 * routine if the result of a read was all 0xff's and you want to 416 * find out if this is due to an EEH slot freeze. This routine 417 * will query firmware for the EEH status. 418 * 419 * Returns 0 if there has not been an EEH error; otherwise returns 420 * a non-zero value and queues up a slot isolation event notification. 421 * 422 * It is safe to call this routine in an interrupt context. 423 */ 424 int eeh_dev_check_failure(struct eeh_dev *edev) 425 { 426 int ret; 427 unsigned long flags; 428 struct device_node *dn; 429 struct pci_dev *dev; 430 struct eeh_pe *pe, *parent_pe; 431 int rc = 0; 432 const char *location = NULL; 433 434 eeh_stats.total_mmio_ffs++; 435 436 if (!eeh_enabled()) 437 return 0; 438 439 if (!edev) { 440 eeh_stats.no_dn++; 441 return 0; 442 } 443 dev = eeh_dev_to_pci_dev(edev); 444 pe = eeh_dev_to_pe(edev); 445 446 /* Access to IO BARs might get this far and still not want checking. */ 447 if (!pe) { 448 eeh_stats.ignored_check++; 449 eeh_edev_dbg(edev, "Ignored check\n"); 450 return 0; 451 } 452 453 /* 454 * On PowerNV platform, we might already have fenced PHB 455 * there and we need take care of that firstly. 456 */ 457 ret = eeh_phb_check_failure(pe); 458 if (ret > 0) 459 return ret; 460 461 /* 462 * If the PE isn't owned by us, we shouldn't check the 463 * state. Instead, let the owner handle it if the PE has 464 * been frozen. 465 */ 466 if (eeh_pe_passed(pe)) 467 return 0; 468 469 /* If we already have a pending isolation event for this 470 * slot, we know it's bad already, we don't need to check. 471 * Do this checking under a lock; as multiple PCI devices 472 * in one slot might report errors simultaneously, and we 473 * only want one error recovery routine running. 474 */ 475 eeh_serialize_lock(&flags); 476 rc = 1; 477 if (pe->state & EEH_PE_ISOLATED) { 478 pe->check_count++; 479 if (pe->check_count == EEH_MAX_FAILS) { 480 dn = pci_device_to_OF_node(dev); 481 if (dn) 482 location = of_get_property(dn, "ibm,loc-code", 483 NULL); 484 eeh_edev_err(edev, "%d reads ignored for recovering device at location=%s driver=%s\n", 485 pe->check_count, 486 location ? location : "unknown", 487 eeh_driver_name(dev)); 488 eeh_edev_err(edev, "Might be infinite loop in %s driver\n", 489 eeh_driver_name(dev)); 490 dump_stack(); 491 } 492 goto dn_unlock; 493 } 494 495 /* 496 * Now test for an EEH failure. This is VERY expensive. 497 * Note that the eeh_config_addr may be a parent device 498 * in the case of a device behind a bridge, or it may be 499 * function zero of a multi-function device. 500 * In any case they must share a common PHB. 501 */ 502 ret = eeh_ops->get_state(pe, NULL); 503 504 /* Note that config-io to empty slots may fail; 505 * they are empty when they don't have children. 506 * We will punt with the following conditions: Failure to get 507 * PE's state, EEH not support and Permanently unavailable 508 * state, PE is in good state. 509 */ 510 if ((ret < 0) || 511 (ret == EEH_STATE_NOT_SUPPORT) || eeh_state_active(ret)) { 512 eeh_stats.false_positives++; 513 pe->false_positives++; 514 rc = 0; 515 goto dn_unlock; 516 } 517 518 /* 519 * It should be corner case that the parent PE has been 520 * put into frozen state as well. We should take care 521 * that at first. 522 */ 523 parent_pe = pe->parent; 524 while (parent_pe) { 525 /* Hit the ceiling ? */ 526 if (parent_pe->type & EEH_PE_PHB) 527 break; 528 529 /* Frozen parent PE ? */ 530 ret = eeh_ops->get_state(parent_pe, NULL); 531 if (ret > 0 && !eeh_state_active(ret)) { 532 pe = parent_pe; 533 pr_err("EEH: Failure of PHB#%x-PE#%x will be handled at parent PHB#%x-PE#%x.\n", 534 pe->phb->global_number, pe->addr, 535 pe->phb->global_number, parent_pe->addr); 536 } 537 538 /* Next parent level */ 539 parent_pe = parent_pe->parent; 540 } 541 542 eeh_stats.slot_resets++; 543 544 /* Avoid repeated reports of this failure, including problems 545 * with other functions on this device, and functions under 546 * bridges. 547 */ 548 eeh_pe_mark_isolated(pe); 549 eeh_serialize_unlock(flags); 550 551 /* Most EEH events are due to device driver bugs. Having 552 * a stack trace will help the device-driver authors figure 553 * out what happened. So print that out. 554 */ 555 pr_debug("EEH: %s: Frozen PHB#%x-PE#%x detected\n", 556 __func__, pe->phb->global_number, pe->addr); 557 eeh_send_failure_event(pe); 558 559 return 1; 560 561 dn_unlock: 562 eeh_serialize_unlock(flags); 563 return rc; 564 } 565 566 EXPORT_SYMBOL_GPL(eeh_dev_check_failure); 567 568 /** 569 * eeh_check_failure - Check if all 1's data is due to EEH slot freeze 570 * @token: I/O address 571 * 572 * Check for an EEH failure at the given I/O address. Call this 573 * routine if the result of a read was all 0xff's and you want to 574 * find out if this is due to an EEH slot freeze event. This routine 575 * will query firmware for the EEH status. 576 * 577 * Note this routine is safe to call in an interrupt context. 578 */ 579 int eeh_check_failure(const volatile void __iomem *token) 580 { 581 unsigned long addr; 582 struct eeh_dev *edev; 583 584 /* Finding the phys addr + pci device; this is pretty quick. */ 585 addr = eeh_token_to_phys((unsigned long __force) token); 586 edev = eeh_addr_cache_get_dev(addr); 587 if (!edev) { 588 eeh_stats.no_device++; 589 return 0; 590 } 591 592 return eeh_dev_check_failure(edev); 593 } 594 EXPORT_SYMBOL(eeh_check_failure); 595 596 597 /** 598 * eeh_pci_enable - Enable MMIO or DMA transfers for this slot 599 * @pe: EEH PE 600 * @function: EEH option 601 * 602 * This routine should be called to reenable frozen MMIO or DMA 603 * so that it would work correctly again. It's useful while doing 604 * recovery or log collection on the indicated device. 605 */ 606 int eeh_pci_enable(struct eeh_pe *pe, int function) 607 { 608 int active_flag, rc; 609 610 /* 611 * pHyp doesn't allow to enable IO or DMA on unfrozen PE. 612 * Also, it's pointless to enable them on unfrozen PE. So 613 * we have to check before enabling IO or DMA. 614 */ 615 switch (function) { 616 case EEH_OPT_THAW_MMIO: 617 active_flag = EEH_STATE_MMIO_ACTIVE | EEH_STATE_MMIO_ENABLED; 618 break; 619 case EEH_OPT_THAW_DMA: 620 active_flag = EEH_STATE_DMA_ACTIVE; 621 break; 622 case EEH_OPT_DISABLE: 623 case EEH_OPT_ENABLE: 624 case EEH_OPT_FREEZE_PE: 625 active_flag = 0; 626 break; 627 default: 628 pr_warn("%s: Invalid function %d\n", 629 __func__, function); 630 return -EINVAL; 631 } 632 633 /* 634 * Check if IO or DMA has been enabled before 635 * enabling them. 636 */ 637 if (active_flag) { 638 rc = eeh_ops->get_state(pe, NULL); 639 if (rc < 0) 640 return rc; 641 642 /* Needn't enable it at all */ 643 if (rc == EEH_STATE_NOT_SUPPORT) 644 return 0; 645 646 /* It's already enabled */ 647 if (rc & active_flag) 648 return 0; 649 } 650 651 652 /* Issue the request */ 653 rc = eeh_ops->set_option(pe, function); 654 if (rc) 655 pr_warn("%s: Unexpected state change %d on " 656 "PHB#%x-PE#%x, err=%d\n", 657 __func__, function, pe->phb->global_number, 658 pe->addr, rc); 659 660 /* Check if the request is finished successfully */ 661 if (active_flag) { 662 rc = eeh_wait_state(pe, PCI_BUS_RESET_WAIT_MSEC); 663 if (rc < 0) 664 return rc; 665 666 if (rc & active_flag) 667 return 0; 668 669 return -EIO; 670 } 671 672 return rc; 673 } 674 675 static void eeh_disable_and_save_dev_state(struct eeh_dev *edev, 676 void *userdata) 677 { 678 struct pci_dev *pdev = eeh_dev_to_pci_dev(edev); 679 struct pci_dev *dev = userdata; 680 681 /* 682 * The caller should have disabled and saved the 683 * state for the specified device 684 */ 685 if (!pdev || pdev == dev) 686 return; 687 688 /* Ensure we have D0 power state */ 689 pci_set_power_state(pdev, PCI_D0); 690 691 /* Save device state */ 692 pci_save_state(pdev); 693 694 /* 695 * Disable device to avoid any DMA traffic and 696 * interrupt from the device 697 */ 698 pci_write_config_word(pdev, PCI_COMMAND, PCI_COMMAND_INTX_DISABLE); 699 } 700 701 static void eeh_restore_dev_state(struct eeh_dev *edev, void *userdata) 702 { 703 struct pci_dev *pdev = eeh_dev_to_pci_dev(edev); 704 struct pci_dev *dev = userdata; 705 706 if (!pdev) 707 return; 708 709 /* Apply customization from firmware */ 710 if (eeh_ops->restore_config) 711 eeh_ops->restore_config(edev); 712 713 /* The caller should restore state for the specified device */ 714 if (pdev != dev) 715 pci_restore_state(pdev); 716 } 717 718 /** 719 * pcibios_set_pcie_reset_state - Set PCI-E reset state 720 * @dev: pci device struct 721 * @state: reset state to enter 722 * 723 * Return value: 724 * 0 if success 725 */ 726 int pcibios_set_pcie_reset_state(struct pci_dev *dev, enum pcie_reset_state state) 727 { 728 struct eeh_dev *edev = pci_dev_to_eeh_dev(dev); 729 struct eeh_pe *pe = eeh_dev_to_pe(edev); 730 731 if (!pe) { 732 pr_err("%s: No PE found on PCI device %s\n", 733 __func__, pci_name(dev)); 734 return -EINVAL; 735 } 736 737 switch (state) { 738 case pcie_deassert_reset: 739 eeh_ops->reset(pe, EEH_RESET_DEACTIVATE); 740 eeh_unfreeze_pe(pe); 741 if (!(pe->type & EEH_PE_VF)) 742 eeh_pe_state_clear(pe, EEH_PE_CFG_BLOCKED, true); 743 eeh_pe_dev_traverse(pe, eeh_restore_dev_state, dev); 744 eeh_pe_state_clear(pe, EEH_PE_ISOLATED, true); 745 break; 746 case pcie_hot_reset: 747 eeh_pe_mark_isolated(pe); 748 eeh_pe_state_clear(pe, EEH_PE_CFG_BLOCKED, true); 749 eeh_ops->set_option(pe, EEH_OPT_FREEZE_PE); 750 eeh_pe_dev_traverse(pe, eeh_disable_and_save_dev_state, dev); 751 if (!(pe->type & EEH_PE_VF)) 752 eeh_pe_state_mark(pe, EEH_PE_CFG_BLOCKED); 753 eeh_ops->reset(pe, EEH_RESET_HOT); 754 break; 755 case pcie_warm_reset: 756 eeh_pe_mark_isolated(pe); 757 eeh_pe_state_clear(pe, EEH_PE_CFG_BLOCKED, true); 758 eeh_ops->set_option(pe, EEH_OPT_FREEZE_PE); 759 eeh_pe_dev_traverse(pe, eeh_disable_and_save_dev_state, dev); 760 if (!(pe->type & EEH_PE_VF)) 761 eeh_pe_state_mark(pe, EEH_PE_CFG_BLOCKED); 762 eeh_ops->reset(pe, EEH_RESET_FUNDAMENTAL); 763 break; 764 default: 765 eeh_pe_state_clear(pe, EEH_PE_ISOLATED | EEH_PE_CFG_BLOCKED, true); 766 return -EINVAL; 767 } 768 769 return 0; 770 } 771 772 /** 773 * eeh_set_dev_freset - Check the required reset for the indicated device 774 * @edev: EEH device 775 * @flag: return value 776 * 777 * Each device might have its preferred reset type: fundamental or 778 * hot reset. The routine is used to collected the information for 779 * the indicated device and its children so that the bunch of the 780 * devices could be reset properly. 781 */ 782 static void eeh_set_dev_freset(struct eeh_dev *edev, void *flag) 783 { 784 struct pci_dev *dev; 785 unsigned int *freset = (unsigned int *)flag; 786 787 dev = eeh_dev_to_pci_dev(edev); 788 if (dev) 789 *freset |= dev->needs_freset; 790 } 791 792 static void eeh_pe_refreeze_passed(struct eeh_pe *root) 793 { 794 struct eeh_pe *pe; 795 int state; 796 797 eeh_for_each_pe(root, pe) { 798 if (eeh_pe_passed(pe)) { 799 state = eeh_ops->get_state(pe, NULL); 800 if (state & 801 (EEH_STATE_MMIO_ACTIVE | EEH_STATE_MMIO_ENABLED)) { 802 pr_info("EEH: Passed-through PE PHB#%x-PE#%x was thawed by reset, re-freezing for safety.\n", 803 pe->phb->global_number, pe->addr); 804 eeh_pe_set_option(pe, EEH_OPT_FREEZE_PE); 805 } 806 } 807 } 808 } 809 810 /** 811 * eeh_pe_reset_full - Complete a full reset process on the indicated PE 812 * @pe: EEH PE 813 * @include_passed: include passed-through devices? 814 * 815 * This function executes a full reset procedure on a PE, including setting 816 * the appropriate flags, performing a fundamental or hot reset, and then 817 * deactivating the reset status. It is designed to be used within the EEH 818 * subsystem, as opposed to eeh_pe_reset which is exported to drivers and 819 * only performs a single operation at a time. 820 * 821 * This function will attempt to reset a PE three times before failing. 822 */ 823 int eeh_pe_reset_full(struct eeh_pe *pe, bool include_passed) 824 { 825 int reset_state = (EEH_PE_RESET | EEH_PE_CFG_BLOCKED); 826 int type = EEH_RESET_HOT; 827 unsigned int freset = 0; 828 int i, state = 0, ret; 829 830 /* 831 * Determine the type of reset to perform - hot or fundamental. 832 * Hot reset is the default operation, unless any device under the 833 * PE requires a fundamental reset. 834 */ 835 eeh_pe_dev_traverse(pe, eeh_set_dev_freset, &freset); 836 837 if (freset) 838 type = EEH_RESET_FUNDAMENTAL; 839 840 /* Mark the PE as in reset state and block config space accesses */ 841 eeh_pe_state_mark(pe, reset_state); 842 843 /* Make three attempts at resetting the bus */ 844 for (i = 0; i < 3; i++) { 845 ret = eeh_pe_reset(pe, type, include_passed); 846 if (!ret) 847 ret = eeh_pe_reset(pe, EEH_RESET_DEACTIVATE, 848 include_passed); 849 if (ret) { 850 ret = -EIO; 851 pr_warn("EEH: Failure %d resetting PHB#%x-PE#%x (attempt %d)\n\n", 852 state, pe->phb->global_number, pe->addr, i + 1); 853 continue; 854 } 855 if (i) 856 pr_warn("EEH: PHB#%x-PE#%x: Successful reset (attempt %d)\n", 857 pe->phb->global_number, pe->addr, i + 1); 858 859 /* Wait until the PE is in a functioning state */ 860 state = eeh_wait_state(pe, PCI_BUS_RESET_WAIT_MSEC); 861 if (state < 0) { 862 pr_warn("EEH: Unrecoverable slot failure on PHB#%x-PE#%x", 863 pe->phb->global_number, pe->addr); 864 ret = -ENOTRECOVERABLE; 865 break; 866 } 867 if (eeh_state_active(state)) 868 break; 869 else 870 pr_warn("EEH: PHB#%x-PE#%x: Slot inactive after reset: 0x%x (attempt %d)\n", 871 pe->phb->global_number, pe->addr, state, i + 1); 872 } 873 874 /* Resetting the PE may have unfrozen child PEs. If those PEs have been 875 * (potentially) passed through to a guest, re-freeze them: 876 */ 877 if (!include_passed) 878 eeh_pe_refreeze_passed(pe); 879 880 eeh_pe_state_clear(pe, reset_state, true); 881 return ret; 882 } 883 884 /** 885 * eeh_save_bars - Save device bars 886 * @edev: PCI device associated EEH device 887 * 888 * Save the values of the device bars. Unlike the restore 889 * routine, this routine is *not* recursive. This is because 890 * PCI devices are added individually; but, for the restore, 891 * an entire slot is reset at a time. 892 */ 893 void eeh_save_bars(struct eeh_dev *edev) 894 { 895 int i; 896 897 if (!edev) 898 return; 899 900 for (i = 0; i < 16; i++) 901 eeh_ops->read_config(edev, i * 4, 4, &edev->config_space[i]); 902 903 /* 904 * For PCI bridges including root port, we need enable bus 905 * master explicitly. Otherwise, it can't fetch IODA table 906 * entries correctly. So we cache the bit in advance so that 907 * we can restore it after reset, either PHB range or PE range. 908 */ 909 if (edev->mode & EEH_DEV_BRIDGE) 910 edev->config_space[1] |= PCI_COMMAND_MASTER; 911 } 912 913 static int eeh_reboot_notifier(struct notifier_block *nb, 914 unsigned long action, void *unused) 915 { 916 eeh_clear_flag(EEH_ENABLED); 917 return NOTIFY_DONE; 918 } 919 920 static struct notifier_block eeh_reboot_nb = { 921 .notifier_call = eeh_reboot_notifier, 922 }; 923 924 static int eeh_device_notifier(struct notifier_block *nb, 925 unsigned long action, void *data) 926 { 927 struct device *dev = data; 928 929 switch (action) { 930 /* 931 * Note: It's not possible to perform EEH device addition (i.e. 932 * {pseries,pnv}_pcibios_bus_add_device()) here because it depends on 933 * the device's resources, which have not yet been set up. 934 */ 935 case BUS_NOTIFY_DEL_DEVICE: 936 eeh_remove_device(to_pci_dev(dev)); 937 break; 938 default: 939 break; 940 } 941 return NOTIFY_DONE; 942 } 943 944 static struct notifier_block eeh_device_nb = { 945 .notifier_call = eeh_device_notifier, 946 }; 947 948 /** 949 * eeh_init - System wide EEH initialization 950 * @ops: struct to trace EEH operation callback functions 951 * 952 * It's the platform's job to call this from an arch_initcall(). 953 */ 954 int eeh_init(struct eeh_ops *ops) 955 { 956 struct pci_controller *hose, *tmp; 957 int ret = 0; 958 959 /* the platform should only initialise EEH once */ 960 if (WARN_ON(eeh_ops)) 961 return -EEXIST; 962 if (WARN_ON(!ops)) 963 return -ENOENT; 964 eeh_ops = ops; 965 966 /* Register reboot notifier */ 967 ret = register_reboot_notifier(&eeh_reboot_nb); 968 if (ret) { 969 pr_warn("%s: Failed to register reboot notifier (%d)\n", 970 __func__, ret); 971 return ret; 972 } 973 974 ret = bus_register_notifier(&pci_bus_type, &eeh_device_nb); 975 if (ret) { 976 pr_warn("%s: Failed to register bus notifier (%d)\n", 977 __func__, ret); 978 return ret; 979 } 980 981 /* Initialize PHB PEs */ 982 list_for_each_entry_safe(hose, tmp, &hose_list, list_node) 983 eeh_phb_pe_create(hose); 984 985 eeh_addr_cache_init(); 986 987 /* Initialize EEH event */ 988 return eeh_event_init(); 989 } 990 991 /** 992 * eeh_probe_device() - Perform EEH initialization for the indicated pci device 993 * @dev: pci device for which to set up EEH 994 * 995 * This routine must be used to complete EEH initialization for PCI 996 * devices that were added after system boot (e.g. hotplug, dlpar). 997 */ 998 void eeh_probe_device(struct pci_dev *dev) 999 { 1000 struct eeh_dev *edev; 1001 1002 pr_debug("EEH: Adding device %s\n", pci_name(dev)); 1003 1004 /* 1005 * pci_dev_to_eeh_dev() can only work if eeh_probe_dev() was 1006 * already called for this device. 1007 */ 1008 if (WARN_ON_ONCE(pci_dev_to_eeh_dev(dev))) { 1009 pci_dbg(dev, "Already bound to an eeh_dev!\n"); 1010 return; 1011 } 1012 1013 edev = eeh_ops->probe(dev); 1014 if (!edev) { 1015 pr_debug("EEH: Adding device failed\n"); 1016 return; 1017 } 1018 1019 /* 1020 * FIXME: We rely on pcibios_release_device() to remove the 1021 * existing EEH state. The release function is only called if 1022 * the pci_dev's refcount drops to zero so if something is 1023 * keeping a ref to a device (e.g. a filesystem) we need to 1024 * remove the old EEH state. 1025 * 1026 * FIXME: HEY MA, LOOK AT ME, NO LOCKING! 1027 */ 1028 if (edev->pdev && edev->pdev != dev) { 1029 eeh_pe_tree_remove(edev); 1030 eeh_addr_cache_rmv_dev(edev->pdev); 1031 eeh_sysfs_remove_device(edev->pdev); 1032 1033 /* 1034 * We definitely should have the PCI device removed 1035 * though it wasn't correctly. So we needn't call 1036 * into error handler afterwards. 1037 */ 1038 edev->mode |= EEH_DEV_NO_HANDLER; 1039 } 1040 1041 /* bind the pdev and the edev together */ 1042 edev->pdev = dev; 1043 dev->dev.archdata.edev = edev; 1044 eeh_addr_cache_insert_dev(dev); 1045 eeh_sysfs_add_device(dev); 1046 } 1047 1048 /** 1049 * eeh_remove_device - Undo EEH setup for the indicated pci device 1050 * @dev: pci device to be removed 1051 * 1052 * This routine should be called when a device is removed from 1053 * a running system (e.g. by hotplug or dlpar). It unregisters 1054 * the PCI device from the EEH subsystem. I/O errors affecting 1055 * this device will no longer be detected after this call; thus, 1056 * i/o errors affecting this slot may leave this device unusable. 1057 */ 1058 void eeh_remove_device(struct pci_dev *dev) 1059 { 1060 struct eeh_dev *edev; 1061 1062 if (!dev || !eeh_enabled()) 1063 return; 1064 edev = pci_dev_to_eeh_dev(dev); 1065 1066 /* Unregister the device with the EEH/PCI address search system */ 1067 dev_dbg(&dev->dev, "EEH: Removing device\n"); 1068 1069 if (!edev || !edev->pdev || !edev->pe) { 1070 dev_dbg(&dev->dev, "EEH: Device not referenced!\n"); 1071 return; 1072 } 1073 1074 /* 1075 * During the hotplug for EEH error recovery, we need the EEH 1076 * device attached to the parent PE in order for BAR restore 1077 * a bit later. So we keep it for BAR restore and remove it 1078 * from the parent PE during the BAR resotre. 1079 */ 1080 edev->pdev = NULL; 1081 1082 /* 1083 * eeh_sysfs_remove_device() uses pci_dev_to_eeh_dev() so we need to 1084 * remove the sysfs files before clearing dev.archdata.edev 1085 */ 1086 if (edev->mode & EEH_DEV_SYSFS) 1087 eeh_sysfs_remove_device(dev); 1088 1089 /* 1090 * We're removing from the PCI subsystem, that means 1091 * the PCI device driver can't support EEH or not 1092 * well. So we rely on hotplug completely to do recovery 1093 * for the specific PCI device. 1094 */ 1095 edev->mode |= EEH_DEV_NO_HANDLER; 1096 1097 eeh_addr_cache_rmv_dev(dev); 1098 1099 /* 1100 * The flag "in_error" is used to trace EEH devices for VFs 1101 * in error state or not. It's set in eeh_report_error(). If 1102 * it's not set, eeh_report_{reset,resume}() won't be called 1103 * for the VF EEH device. 1104 */ 1105 edev->in_error = false; 1106 dev->dev.archdata.edev = NULL; 1107 if (!(edev->pe->state & EEH_PE_KEEP)) 1108 eeh_pe_tree_remove(edev); 1109 else 1110 edev->mode |= EEH_DEV_DISCONNECTED; 1111 } 1112 1113 int eeh_unfreeze_pe(struct eeh_pe *pe) 1114 { 1115 int ret; 1116 1117 ret = eeh_pci_enable(pe, EEH_OPT_THAW_MMIO); 1118 if (ret) { 1119 pr_warn("%s: Failure %d enabling IO on PHB#%x-PE#%x\n", 1120 __func__, ret, pe->phb->global_number, pe->addr); 1121 return ret; 1122 } 1123 1124 ret = eeh_pci_enable(pe, EEH_OPT_THAW_DMA); 1125 if (ret) { 1126 pr_warn("%s: Failure %d enabling DMA on PHB#%x-PE#%x\n", 1127 __func__, ret, pe->phb->global_number, pe->addr); 1128 return ret; 1129 } 1130 1131 return ret; 1132 } 1133 1134 1135 static struct pci_device_id eeh_reset_ids[] = { 1136 { PCI_DEVICE(0x19a2, 0x0710) }, /* Emulex, BE */ 1137 { PCI_DEVICE(0x10df, 0xe220) }, /* Emulex, Lancer */ 1138 { PCI_DEVICE(0x14e4, 0x1657) }, /* Broadcom BCM5719 */ 1139 { 0 } 1140 }; 1141 1142 static int eeh_pe_change_owner(struct eeh_pe *pe) 1143 { 1144 struct eeh_dev *edev, *tmp; 1145 struct pci_dev *pdev; 1146 struct pci_device_id *id; 1147 int ret; 1148 1149 /* Check PE state */ 1150 ret = eeh_ops->get_state(pe, NULL); 1151 if (ret < 0 || ret == EEH_STATE_NOT_SUPPORT) 1152 return 0; 1153 1154 /* Unfrozen PE, nothing to do */ 1155 if (eeh_state_active(ret)) 1156 return 0; 1157 1158 /* Frozen PE, check if it needs PE level reset */ 1159 eeh_pe_for_each_dev(pe, edev, tmp) { 1160 pdev = eeh_dev_to_pci_dev(edev); 1161 if (!pdev) 1162 continue; 1163 1164 for (id = &eeh_reset_ids[0]; id->vendor != 0; id++) { 1165 if (id->vendor != PCI_ANY_ID && 1166 id->vendor != pdev->vendor) 1167 continue; 1168 if (id->device != PCI_ANY_ID && 1169 id->device != pdev->device) 1170 continue; 1171 if (id->subvendor != PCI_ANY_ID && 1172 id->subvendor != pdev->subsystem_vendor) 1173 continue; 1174 if (id->subdevice != PCI_ANY_ID && 1175 id->subdevice != pdev->subsystem_device) 1176 continue; 1177 1178 return eeh_pe_reset_and_recover(pe); 1179 } 1180 } 1181 1182 ret = eeh_unfreeze_pe(pe); 1183 if (!ret) 1184 eeh_pe_state_clear(pe, EEH_PE_ISOLATED, true); 1185 return ret; 1186 } 1187 1188 /** 1189 * eeh_dev_open - Increase count of pass through devices for PE 1190 * @pdev: PCI device 1191 * 1192 * Increase count of passed through devices for the indicated 1193 * PE. In the result, the EEH errors detected on the PE won't be 1194 * reported. The PE owner will be responsible for detection 1195 * and recovery. 1196 */ 1197 int eeh_dev_open(struct pci_dev *pdev) 1198 { 1199 struct eeh_dev *edev; 1200 int ret = -ENODEV; 1201 1202 mutex_lock(&eeh_dev_mutex); 1203 1204 /* No PCI device ? */ 1205 if (!pdev) 1206 goto out; 1207 1208 /* No EEH device or PE ? */ 1209 edev = pci_dev_to_eeh_dev(pdev); 1210 if (!edev || !edev->pe) 1211 goto out; 1212 1213 /* 1214 * The PE might have been put into frozen state, but we 1215 * didn't detect that yet. The passed through PCI devices 1216 * in frozen PE won't work properly. Clear the frozen state 1217 * in advance. 1218 */ 1219 ret = eeh_pe_change_owner(edev->pe); 1220 if (ret) 1221 goto out; 1222 1223 /* Increase PE's pass through count */ 1224 atomic_inc(&edev->pe->pass_dev_cnt); 1225 mutex_unlock(&eeh_dev_mutex); 1226 1227 return 0; 1228 out: 1229 mutex_unlock(&eeh_dev_mutex); 1230 return ret; 1231 } 1232 EXPORT_SYMBOL_GPL(eeh_dev_open); 1233 1234 /** 1235 * eeh_dev_release - Decrease count of pass through devices for PE 1236 * @pdev: PCI device 1237 * 1238 * Decrease count of pass through devices for the indicated PE. If 1239 * there is no passed through device in PE, the EEH errors detected 1240 * on the PE will be reported and handled as usual. 1241 */ 1242 void eeh_dev_release(struct pci_dev *pdev) 1243 { 1244 struct eeh_dev *edev; 1245 1246 mutex_lock(&eeh_dev_mutex); 1247 1248 /* No PCI device ? */ 1249 if (!pdev) 1250 goto out; 1251 1252 /* No EEH device ? */ 1253 edev = pci_dev_to_eeh_dev(pdev); 1254 if (!edev || !edev->pe || !eeh_pe_passed(edev->pe)) 1255 goto out; 1256 1257 /* Decrease PE's pass through count */ 1258 WARN_ON(atomic_dec_if_positive(&edev->pe->pass_dev_cnt) < 0); 1259 eeh_pe_change_owner(edev->pe); 1260 out: 1261 mutex_unlock(&eeh_dev_mutex); 1262 } 1263 EXPORT_SYMBOL(eeh_dev_release); 1264 1265 #ifdef CONFIG_IOMMU_API 1266 1267 static int dev_has_iommu_table(struct device *dev, void *data) 1268 { 1269 struct pci_dev *pdev = to_pci_dev(dev); 1270 struct pci_dev **ppdev = data; 1271 1272 if (!dev) 1273 return 0; 1274 1275 if (device_iommu_mapped(dev)) { 1276 *ppdev = pdev; 1277 return 1; 1278 } 1279 1280 return 0; 1281 } 1282 1283 /** 1284 * eeh_iommu_group_to_pe - Convert IOMMU group to EEH PE 1285 * @group: IOMMU group 1286 * 1287 * The routine is called to convert IOMMU group to EEH PE. 1288 */ 1289 struct eeh_pe *eeh_iommu_group_to_pe(struct iommu_group *group) 1290 { 1291 struct pci_dev *pdev = NULL; 1292 struct eeh_dev *edev; 1293 int ret; 1294 1295 /* No IOMMU group ? */ 1296 if (!group) 1297 return NULL; 1298 1299 ret = iommu_group_for_each_dev(group, &pdev, dev_has_iommu_table); 1300 if (!ret || !pdev) 1301 return NULL; 1302 1303 /* No EEH device or PE ? */ 1304 edev = pci_dev_to_eeh_dev(pdev); 1305 if (!edev || !edev->pe) 1306 return NULL; 1307 1308 return edev->pe; 1309 } 1310 EXPORT_SYMBOL_GPL(eeh_iommu_group_to_pe); 1311 1312 #endif /* CONFIG_IOMMU_API */ 1313 1314 /** 1315 * eeh_pe_set_option - Set options for the indicated PE 1316 * @pe: EEH PE 1317 * @option: requested option 1318 * 1319 * The routine is called to enable or disable EEH functionality 1320 * on the indicated PE, to enable IO or DMA for the frozen PE. 1321 */ 1322 int eeh_pe_set_option(struct eeh_pe *pe, int option) 1323 { 1324 int ret = 0; 1325 1326 /* Invalid PE ? */ 1327 if (!pe) 1328 return -ENODEV; 1329 1330 /* 1331 * EEH functionality could possibly be disabled, just 1332 * return error for the case. And the EEH functinality 1333 * isn't expected to be disabled on one specific PE. 1334 */ 1335 switch (option) { 1336 case EEH_OPT_ENABLE: 1337 if (eeh_enabled()) { 1338 ret = eeh_pe_change_owner(pe); 1339 break; 1340 } 1341 ret = -EIO; 1342 break; 1343 case EEH_OPT_DISABLE: 1344 break; 1345 case EEH_OPT_THAW_MMIO: 1346 case EEH_OPT_THAW_DMA: 1347 case EEH_OPT_FREEZE_PE: 1348 if (!eeh_ops || !eeh_ops->set_option) { 1349 ret = -ENOENT; 1350 break; 1351 } 1352 1353 ret = eeh_pci_enable(pe, option); 1354 break; 1355 default: 1356 pr_debug("%s: Option %d out of range (%d, %d)\n", 1357 __func__, option, EEH_OPT_DISABLE, EEH_OPT_THAW_DMA); 1358 ret = -EINVAL; 1359 } 1360 1361 return ret; 1362 } 1363 EXPORT_SYMBOL_GPL(eeh_pe_set_option); 1364 1365 /** 1366 * eeh_pe_get_state - Retrieve PE's state 1367 * @pe: EEH PE 1368 * 1369 * Retrieve the PE's state, which includes 3 aspects: enabled 1370 * DMA, enabled IO and asserted reset. 1371 */ 1372 int eeh_pe_get_state(struct eeh_pe *pe) 1373 { 1374 int result, ret = 0; 1375 bool rst_active, dma_en, mmio_en; 1376 1377 /* Existing PE ? */ 1378 if (!pe) 1379 return -ENODEV; 1380 1381 if (!eeh_ops || !eeh_ops->get_state) 1382 return -ENOENT; 1383 1384 /* 1385 * If the parent PE is owned by the host kernel and is undergoing 1386 * error recovery, we should return the PE state as temporarily 1387 * unavailable so that the error recovery on the guest is suspended 1388 * until the recovery completes on the host. 1389 */ 1390 if (pe->parent && 1391 !(pe->state & EEH_PE_REMOVED) && 1392 (pe->parent->state & (EEH_PE_ISOLATED | EEH_PE_RECOVERING))) 1393 return EEH_PE_STATE_UNAVAIL; 1394 1395 result = eeh_ops->get_state(pe, NULL); 1396 rst_active = !!(result & EEH_STATE_RESET_ACTIVE); 1397 dma_en = !!(result & EEH_STATE_DMA_ENABLED); 1398 mmio_en = !!(result & EEH_STATE_MMIO_ENABLED); 1399 1400 if (rst_active) 1401 ret = EEH_PE_STATE_RESET; 1402 else if (dma_en && mmio_en) 1403 ret = EEH_PE_STATE_NORMAL; 1404 else if (!dma_en && !mmio_en) 1405 ret = EEH_PE_STATE_STOPPED_IO_DMA; 1406 else if (!dma_en && mmio_en) 1407 ret = EEH_PE_STATE_STOPPED_DMA; 1408 else 1409 ret = EEH_PE_STATE_UNAVAIL; 1410 1411 return ret; 1412 } 1413 EXPORT_SYMBOL_GPL(eeh_pe_get_state); 1414 1415 static int eeh_pe_reenable_devices(struct eeh_pe *pe, bool include_passed) 1416 { 1417 struct eeh_dev *edev, *tmp; 1418 struct pci_dev *pdev; 1419 int ret = 0; 1420 1421 eeh_pe_restore_bars(pe); 1422 1423 /* 1424 * Reenable PCI devices as the devices passed 1425 * through are always enabled before the reset. 1426 */ 1427 eeh_pe_for_each_dev(pe, edev, tmp) { 1428 pdev = eeh_dev_to_pci_dev(edev); 1429 if (!pdev) 1430 continue; 1431 1432 ret = pci_reenable_device(pdev); 1433 if (ret) { 1434 pr_warn("%s: Failure %d reenabling %s\n", 1435 __func__, ret, pci_name(pdev)); 1436 return ret; 1437 } 1438 } 1439 1440 /* The PE is still in frozen state */ 1441 if (include_passed || !eeh_pe_passed(pe)) { 1442 ret = eeh_unfreeze_pe(pe); 1443 } else 1444 pr_info("EEH: Note: Leaving passthrough PHB#%x-PE#%x frozen.\n", 1445 pe->phb->global_number, pe->addr); 1446 if (!ret) 1447 eeh_pe_state_clear(pe, EEH_PE_ISOLATED, include_passed); 1448 return ret; 1449 } 1450 1451 1452 /** 1453 * eeh_pe_reset - Issue PE reset according to specified type 1454 * @pe: EEH PE 1455 * @option: reset type 1456 * @include_passed: include passed-through devices? 1457 * 1458 * The routine is called to reset the specified PE with the 1459 * indicated type, either fundamental reset or hot reset. 1460 * PE reset is the most important part for error recovery. 1461 */ 1462 int eeh_pe_reset(struct eeh_pe *pe, int option, bool include_passed) 1463 { 1464 int ret = 0; 1465 1466 /* Invalid PE ? */ 1467 if (!pe) 1468 return -ENODEV; 1469 1470 if (!eeh_ops || !eeh_ops->set_option || !eeh_ops->reset) 1471 return -ENOENT; 1472 1473 switch (option) { 1474 case EEH_RESET_DEACTIVATE: 1475 ret = eeh_ops->reset(pe, option); 1476 eeh_pe_state_clear(pe, EEH_PE_CFG_BLOCKED, include_passed); 1477 if (ret) 1478 break; 1479 1480 ret = eeh_pe_reenable_devices(pe, include_passed); 1481 break; 1482 case EEH_RESET_HOT: 1483 case EEH_RESET_FUNDAMENTAL: 1484 /* 1485 * Proactively freeze the PE to drop all MMIO access 1486 * during reset, which should be banned as it's always 1487 * cause recursive EEH error. 1488 */ 1489 eeh_ops->set_option(pe, EEH_OPT_FREEZE_PE); 1490 1491 eeh_pe_state_mark(pe, EEH_PE_CFG_BLOCKED); 1492 ret = eeh_ops->reset(pe, option); 1493 break; 1494 default: 1495 pr_debug("%s: Unsupported option %d\n", 1496 __func__, option); 1497 ret = -EINVAL; 1498 } 1499 1500 return ret; 1501 } 1502 EXPORT_SYMBOL_GPL(eeh_pe_reset); 1503 1504 /** 1505 * eeh_pe_configure - Configure PCI bridges after PE reset 1506 * @pe: EEH PE 1507 * 1508 * The routine is called to restore the PCI config space for 1509 * those PCI devices, especially PCI bridges affected by PE 1510 * reset issued previously. 1511 */ 1512 int eeh_pe_configure(struct eeh_pe *pe) 1513 { 1514 int ret = 0; 1515 1516 /* Invalid PE ? */ 1517 if (!pe) 1518 return -ENODEV; 1519 1520 return ret; 1521 } 1522 EXPORT_SYMBOL_GPL(eeh_pe_configure); 1523 1524 /** 1525 * eeh_pe_inject_err - Injecting the specified PCI error to the indicated PE 1526 * @pe: the indicated PE 1527 * @type: error type 1528 * @func: error function 1529 * @addr: address 1530 * @mask: address mask 1531 * 1532 * The routine is called to inject the specified PCI error, which 1533 * is determined by @type and @func, to the indicated PE for 1534 * testing purpose. 1535 */ 1536 int eeh_pe_inject_err(struct eeh_pe *pe, int type, int func, 1537 unsigned long addr, unsigned long mask) 1538 { 1539 /* Invalid PE ? */ 1540 if (!pe) 1541 return -ENODEV; 1542 1543 /* Unsupported operation ? */ 1544 if (!eeh_ops || !eeh_ops->err_inject) 1545 return -ENOENT; 1546 1547 /* Check on PCI error type */ 1548 if (type != EEH_ERR_TYPE_32 && type != EEH_ERR_TYPE_64) 1549 return -EINVAL; 1550 1551 /* Check on PCI error function */ 1552 if (func < EEH_ERR_FUNC_MIN || func > EEH_ERR_FUNC_MAX) 1553 return -EINVAL; 1554 1555 return eeh_ops->err_inject(pe, type, func, addr, mask); 1556 } 1557 EXPORT_SYMBOL_GPL(eeh_pe_inject_err); 1558 1559 #ifdef CONFIG_PROC_FS 1560 static int proc_eeh_show(struct seq_file *m, void *v) 1561 { 1562 if (!eeh_enabled()) { 1563 seq_printf(m, "EEH Subsystem is globally disabled\n"); 1564 seq_printf(m, "eeh_total_mmio_ffs=%llu\n", eeh_stats.total_mmio_ffs); 1565 } else { 1566 seq_printf(m, "EEH Subsystem is enabled\n"); 1567 seq_printf(m, 1568 "no device=%llu\n" 1569 "no device node=%llu\n" 1570 "no config address=%llu\n" 1571 "check not wanted=%llu\n" 1572 "eeh_total_mmio_ffs=%llu\n" 1573 "eeh_false_positives=%llu\n" 1574 "eeh_slot_resets=%llu\n", 1575 eeh_stats.no_device, 1576 eeh_stats.no_dn, 1577 eeh_stats.no_cfg_addr, 1578 eeh_stats.ignored_check, 1579 eeh_stats.total_mmio_ffs, 1580 eeh_stats.false_positives, 1581 eeh_stats.slot_resets); 1582 } 1583 1584 return 0; 1585 } 1586 #endif /* CONFIG_PROC_FS */ 1587 1588 #ifdef CONFIG_DEBUG_FS 1589 1590 1591 static struct pci_dev *eeh_debug_lookup_pdev(struct file *filp, 1592 const char __user *user_buf, 1593 size_t count, loff_t *ppos) 1594 { 1595 uint32_t domain, bus, dev, fn; 1596 struct pci_dev *pdev; 1597 char buf[20]; 1598 int ret; 1599 1600 memset(buf, 0, sizeof(buf)); 1601 ret = simple_write_to_buffer(buf, sizeof(buf)-1, ppos, user_buf, count); 1602 if (!ret) 1603 return ERR_PTR(-EFAULT); 1604 1605 ret = sscanf(buf, "%x:%x:%x.%x", &domain, &bus, &dev, &fn); 1606 if (ret != 4) { 1607 pr_err("%s: expected 4 args, got %d\n", __func__, ret); 1608 return ERR_PTR(-EINVAL); 1609 } 1610 1611 pdev = pci_get_domain_bus_and_slot(domain, bus, (dev << 3) | fn); 1612 if (!pdev) 1613 return ERR_PTR(-ENODEV); 1614 1615 return pdev; 1616 } 1617 1618 static int eeh_enable_dbgfs_set(void *data, u64 val) 1619 { 1620 if (val) 1621 eeh_clear_flag(EEH_FORCE_DISABLED); 1622 else 1623 eeh_add_flag(EEH_FORCE_DISABLED); 1624 1625 return 0; 1626 } 1627 1628 static int eeh_enable_dbgfs_get(void *data, u64 *val) 1629 { 1630 if (eeh_enabled()) 1631 *val = 0x1ul; 1632 else 1633 *val = 0x0ul; 1634 return 0; 1635 } 1636 1637 DEFINE_DEBUGFS_ATTRIBUTE(eeh_enable_dbgfs_ops, eeh_enable_dbgfs_get, 1638 eeh_enable_dbgfs_set, "0x%llx\n"); 1639 1640 static ssize_t eeh_force_recover_write(struct file *filp, 1641 const char __user *user_buf, 1642 size_t count, loff_t *ppos) 1643 { 1644 struct pci_controller *hose; 1645 uint32_t phbid, pe_no; 1646 struct eeh_pe *pe; 1647 char buf[20]; 1648 int ret; 1649 1650 ret = simple_write_to_buffer(buf, sizeof(buf), ppos, user_buf, count); 1651 if (!ret) 1652 return -EFAULT; 1653 1654 /* 1655 * When PE is NULL the event is a "special" event. Rather than 1656 * recovering a specific PE it forces the EEH core to scan for failed 1657 * PHBs and recovers each. This needs to be done before any device 1658 * recoveries can occur. 1659 */ 1660 if (!strncmp(buf, "hwcheck", 7)) { 1661 __eeh_send_failure_event(NULL); 1662 return count; 1663 } 1664 1665 ret = sscanf(buf, "%x:%x", &phbid, &pe_no); 1666 if (ret != 2) 1667 return -EINVAL; 1668 1669 hose = pci_find_controller_for_domain(phbid); 1670 if (!hose) 1671 return -ENODEV; 1672 1673 /* Retrieve PE */ 1674 pe = eeh_pe_get(hose, pe_no); 1675 if (!pe) 1676 return -ENODEV; 1677 1678 /* 1679 * We don't do any state checking here since the detection 1680 * process is async to the recovery process. The recovery 1681 * thread *should* not break even if we schedule a recovery 1682 * from an odd state (e.g. PE removed, or recovery of a 1683 * non-isolated PE) 1684 */ 1685 __eeh_send_failure_event(pe); 1686 1687 return ret < 0 ? ret : count; 1688 } 1689 1690 static const struct file_operations eeh_force_recover_fops = { 1691 .open = simple_open, 1692 .llseek = no_llseek, 1693 .write = eeh_force_recover_write, 1694 }; 1695 1696 static ssize_t eeh_debugfs_dev_usage(struct file *filp, 1697 char __user *user_buf, 1698 size_t count, loff_t *ppos) 1699 { 1700 static const char usage[] = "input format: <domain>:<bus>:<dev>.<fn>\n"; 1701 1702 return simple_read_from_buffer(user_buf, count, ppos, 1703 usage, sizeof(usage) - 1); 1704 } 1705 1706 static ssize_t eeh_dev_check_write(struct file *filp, 1707 const char __user *user_buf, 1708 size_t count, loff_t *ppos) 1709 { 1710 struct pci_dev *pdev; 1711 struct eeh_dev *edev; 1712 int ret; 1713 1714 pdev = eeh_debug_lookup_pdev(filp, user_buf, count, ppos); 1715 if (IS_ERR(pdev)) 1716 return PTR_ERR(pdev); 1717 1718 edev = pci_dev_to_eeh_dev(pdev); 1719 if (!edev) { 1720 pci_err(pdev, "No eeh_dev for this device!\n"); 1721 pci_dev_put(pdev); 1722 return -ENODEV; 1723 } 1724 1725 ret = eeh_dev_check_failure(edev); 1726 pci_info(pdev, "eeh_dev_check_failure(%s) = %d\n", 1727 pci_name(pdev), ret); 1728 1729 pci_dev_put(pdev); 1730 1731 return count; 1732 } 1733 1734 static const struct file_operations eeh_dev_check_fops = { 1735 .open = simple_open, 1736 .llseek = no_llseek, 1737 .write = eeh_dev_check_write, 1738 .read = eeh_debugfs_dev_usage, 1739 }; 1740 1741 static int eeh_debugfs_break_device(struct pci_dev *pdev) 1742 { 1743 struct resource *bar = NULL; 1744 void __iomem *mapped; 1745 u16 old, bit; 1746 int i, pos; 1747 1748 /* Do we have an MMIO BAR to disable? */ 1749 for (i = 0; i <= PCI_STD_RESOURCE_END; i++) { 1750 struct resource *r = &pdev->resource[i]; 1751 1752 if (!r->flags || !r->start) 1753 continue; 1754 if (r->flags & IORESOURCE_IO) 1755 continue; 1756 if (r->flags & IORESOURCE_UNSET) 1757 continue; 1758 1759 bar = r; 1760 break; 1761 } 1762 1763 if (!bar) { 1764 pci_err(pdev, "Unable to find Memory BAR to cause EEH with\n"); 1765 return -ENXIO; 1766 } 1767 1768 pci_err(pdev, "Going to break: %pR\n", bar); 1769 1770 if (pdev->is_virtfn) { 1771 #ifndef CONFIG_PCI_IOV 1772 return -ENXIO; 1773 #else 1774 /* 1775 * VFs don't have a per-function COMMAND register, so the best 1776 * we can do is clear the Memory Space Enable bit in the PF's 1777 * SRIOV control reg. 1778 * 1779 * Unfortunately, this requires that we have a PF (i.e doesn't 1780 * work for a passed-through VF) and it has the potential side 1781 * effect of also causing an EEH on every other VF under the 1782 * PF. Oh well. 1783 */ 1784 pdev = pdev->physfn; 1785 if (!pdev) 1786 return -ENXIO; /* passed through VFs have no PF */ 1787 1788 pos = pci_find_ext_capability(pdev, PCI_EXT_CAP_ID_SRIOV); 1789 pos += PCI_SRIOV_CTRL; 1790 bit = PCI_SRIOV_CTRL_MSE; 1791 #endif /* !CONFIG_PCI_IOV */ 1792 } else { 1793 bit = PCI_COMMAND_MEMORY; 1794 pos = PCI_COMMAND; 1795 } 1796 1797 /* 1798 * Process here is: 1799 * 1800 * 1. Disable Memory space. 1801 * 1802 * 2. Perform an MMIO to the device. This should result in an error 1803 * (CA / UR) being raised by the device which results in an EEH 1804 * PE freeze. Using the in_8() accessor skips the eeh detection hook 1805 * so the freeze hook so the EEH Detection machinery won't be 1806 * triggered here. This is to match the usual behaviour of EEH 1807 * where the HW will asyncronously freeze a PE and it's up to 1808 * the kernel to notice and deal with it. 1809 * 1810 * 3. Turn Memory space back on. This is more important for VFs 1811 * since recovery will probably fail if we don't. For normal 1812 * the COMMAND register is reset as a part of re-initialising 1813 * the device. 1814 * 1815 * Breaking stuff is the point so who cares if it's racy ;) 1816 */ 1817 pci_read_config_word(pdev, pos, &old); 1818 1819 mapped = ioremap(bar->start, PAGE_SIZE); 1820 if (!mapped) { 1821 pci_err(pdev, "Unable to map MMIO BAR %pR\n", bar); 1822 return -ENXIO; 1823 } 1824 1825 pci_write_config_word(pdev, pos, old & ~bit); 1826 in_8(mapped); 1827 pci_write_config_word(pdev, pos, old); 1828 1829 iounmap(mapped); 1830 1831 return 0; 1832 } 1833 1834 static ssize_t eeh_dev_break_write(struct file *filp, 1835 const char __user *user_buf, 1836 size_t count, loff_t *ppos) 1837 { 1838 struct pci_dev *pdev; 1839 int ret; 1840 1841 pdev = eeh_debug_lookup_pdev(filp, user_buf, count, ppos); 1842 if (IS_ERR(pdev)) 1843 return PTR_ERR(pdev); 1844 1845 ret = eeh_debugfs_break_device(pdev); 1846 pci_dev_put(pdev); 1847 1848 if (ret < 0) 1849 return ret; 1850 1851 return count; 1852 } 1853 1854 static const struct file_operations eeh_dev_break_fops = { 1855 .open = simple_open, 1856 .llseek = no_llseek, 1857 .write = eeh_dev_break_write, 1858 .read = eeh_debugfs_dev_usage, 1859 }; 1860 1861 static ssize_t eeh_dev_can_recover(struct file *filp, 1862 const char __user *user_buf, 1863 size_t count, loff_t *ppos) 1864 { 1865 struct pci_driver *drv; 1866 struct pci_dev *pdev; 1867 size_t ret; 1868 1869 pdev = eeh_debug_lookup_pdev(filp, user_buf, count, ppos); 1870 if (IS_ERR(pdev)) 1871 return PTR_ERR(pdev); 1872 1873 /* 1874 * In order for error recovery to work the driver needs to implement 1875 * .error_detected(), so it can quiesce IO to the device, and 1876 * .slot_reset() so it can re-initialise the device after a reset. 1877 * 1878 * Ideally they'd implement .resume() too, but some drivers which 1879 * we need to support (notably IPR) don't so I guess we can tolerate 1880 * that. 1881 * 1882 * .mmio_enabled() is mostly there as a work-around for devices which 1883 * take forever to re-init after a hot reset. Implementing that is 1884 * strictly optional. 1885 */ 1886 drv = pci_dev_driver(pdev); 1887 if (drv && 1888 drv->err_handler && 1889 drv->err_handler->error_detected && 1890 drv->err_handler->slot_reset) { 1891 ret = count; 1892 } else { 1893 ret = -EOPNOTSUPP; 1894 } 1895 1896 pci_dev_put(pdev); 1897 1898 return ret; 1899 } 1900 1901 static const struct file_operations eeh_dev_can_recover_fops = { 1902 .open = simple_open, 1903 .llseek = no_llseek, 1904 .write = eeh_dev_can_recover, 1905 .read = eeh_debugfs_dev_usage, 1906 }; 1907 1908 #endif 1909 1910 static int __init eeh_init_proc(void) 1911 { 1912 if (machine_is(pseries) || machine_is(powernv)) { 1913 proc_create_single("powerpc/eeh", 0, NULL, proc_eeh_show); 1914 #ifdef CONFIG_DEBUG_FS 1915 debugfs_create_file_unsafe("eeh_enable", 0600, 1916 arch_debugfs_dir, NULL, 1917 &eeh_enable_dbgfs_ops); 1918 debugfs_create_u32("eeh_max_freezes", 0600, 1919 arch_debugfs_dir, &eeh_max_freezes); 1920 debugfs_create_bool("eeh_disable_recovery", 0600, 1921 arch_debugfs_dir, 1922 &eeh_debugfs_no_recover); 1923 debugfs_create_file_unsafe("eeh_dev_check", 0600, 1924 arch_debugfs_dir, NULL, 1925 &eeh_dev_check_fops); 1926 debugfs_create_file_unsafe("eeh_dev_break", 0600, 1927 arch_debugfs_dir, NULL, 1928 &eeh_dev_break_fops); 1929 debugfs_create_file_unsafe("eeh_force_recover", 0600, 1930 arch_debugfs_dir, NULL, 1931 &eeh_force_recover_fops); 1932 debugfs_create_file_unsafe("eeh_dev_can_recover", 0600, 1933 arch_debugfs_dir, NULL, 1934 &eeh_dev_can_recover_fops); 1935 eeh_cache_debugfs_init(); 1936 #endif 1937 } 1938 1939 return 0; 1940 } 1941 __initcall(eeh_init_proc); 1942