1// SPDX-License-Identifier: GPL-2.0-only
2/*
3 * Copyright (C) 2009 Extreme Engineering Solutions, Inc.
4 * Based on TQM8548 device tree
5 *
6 * XPedite5200 PrPMC/XMC module based on MPC8548E.  This dts is for the
7 * xMon boot loader memory map which differs from U-Boot's.
8 */
9
10/dts-v1/;
11
12/ {
13	model = "xes,xpedite5200";
14	compatible = "xes,xpedite5200", "xes,MPC8548";
15	#address-cells = <1>;
16	#size-cells = <1>;
17	form-factor = "PMC/XMC";
18	boot-bank = <0x0>;
19
20	aliases {
21		ethernet0 = &enet0;
22		ethernet1 = &enet1;
23		ethernet2 = &enet2;
24		ethernet3 = &enet3;
25
26		serial0 = &serial0;
27		serial1 = &serial1;
28		pci0 = &pci0;
29		pci1 = &pci1;
30	};
31
32	cpus {
33		#address-cells = <1>;
34		#size-cells = <0>;
35
36		PowerPC,8548@0 {
37			device_type = "cpu";
38			reg = <0>;
39			d-cache-line-size = <32>;	// 32 bytes
40			i-cache-line-size = <32>;	// 32 bytes
41			d-cache-size = <0x8000>;	// L1, 32K
42			i-cache-size = <0x8000>;	// L1, 32K
43			next-level-cache = <&L2>;
44		};
45	};
46
47	memory {
48		device_type = "memory";
49		reg = <0x0 0x0>;	// Filled in by boot loader
50	};
51
52	soc@ef000000 {
53		#address-cells = <1>;
54		#size-cells = <1>;
55		device_type = "soc";
56		ranges = <0x0 0xef000000 0x100000>;
57		bus-frequency = <0>;
58		compatible = "fsl,mpc8548-immr", "simple-bus";
59
60		ecm-law@0 {
61			compatible = "fsl,ecm-law";
62			reg = <0x0 0x1000>;
63			fsl,num-laws = <12>;
64		};
65
66		ecm@1000 {
67			compatible = "fsl,mpc8548-ecm", "fsl,ecm";
68			reg = <0x1000 0x1000>;
69			interrupts = <17 2>;
70			interrupt-parent = <&mpic>;
71		};
72
73		memory-controller@2000 {
74			compatible = "fsl,mpc8548-memory-controller";
75			reg = <0x2000 0x1000>;
76			interrupt-parent = <&mpic>;
77			interrupts = <18 2>;
78		};
79
80		L2: l2-cache-controller@20000 {
81			compatible = "fsl,mpc8548-l2-cache-controller";
82			reg = <0x20000 0x1000>;
83			cache-line-size = <32>;	// 32 bytes
84			cache-size = <0x80000>;	// L2, 512K
85			interrupt-parent = <&mpic>;
86			interrupts = <16 2>;
87		};
88
89		/* On-card I2C */
90		i2c@3000 {
91			#address-cells = <1>;
92			#size-cells = <0>;
93			cell-index = <0>;
94			compatible = "fsl-i2c";
95			reg = <0x3000 0x100>;
96			interrupts = <43 2>;
97			interrupt-parent = <&mpic>;
98			dfsrr;
99
100			/*
101			 * Board GPIO:
102			 * 	0: BRD_CFG0 (1: P14 IO present)
103			 * 	1: BRD_CFG1 (1: FP ethernet present)
104			 * 	2: BRD_CFG2 (1: XMC IO present)
105			 * 	3: XMC root complex indicator
106			 * 	4: Flash boot device indicator
107			 * 	5: Flash write protect enable
108			 * 	6: PMC monarch indicator
109			 * 	7: PMC EREADY
110			 */
111			gpio1: gpio@18 {
112				compatible = "nxp,pca9556";
113				reg = <0x18>;
114				#gpio-cells = <2>;
115				gpio-controller;
116				polarity = <0x00>;
117			};
118
119			/* P14 GPIO */
120			gpio2: gpio@19 {
121				compatible = "nxp,pca9556";
122				reg = <0x19>;
123				#gpio-cells = <2>;
124				gpio-controller;
125				polarity = <0x00>;
126			};
127
128			eeprom@50 {
129				compatible = "atmel,at24c16";
130				reg = <0x50>;
131			};
132
133			rtc@68 {
134				compatible = "st,m41t00",
135					     "dallas,ds1338";
136				reg = <0x68>;
137			};
138
139			dtt@34 {
140				compatible = "maxim,max1237";
141				reg = <0x34>;
142			};
143		};
144
145		/* Off-card I2C */
146		i2c@3100 {
147			#address-cells = <1>;
148			#size-cells = <0>;
149			cell-index = <1>;
150			compatible = "fsl-i2c";
151			reg = <0x3100 0x100>;
152			interrupts = <43 2>;
153			interrupt-parent = <&mpic>;
154			dfsrr;
155		};
156
157		dma@21300 {
158			#address-cells = <1>;
159			#size-cells = <1>;
160			compatible = "fsl,mpc8548-dma", "fsl,eloplus-dma";
161			reg = <0x21300 0x4>;
162			ranges = <0x0 0x21100 0x200>;
163			cell-index = <0>;
164			dma-channel@0 {
165				compatible = "fsl,mpc8548-dma-channel",
166						"fsl,eloplus-dma-channel";
167				reg = <0x0 0x80>;
168				cell-index = <0>;
169				interrupt-parent = <&mpic>;
170				interrupts = <20 2>;
171			};
172			dma-channel@80 {
173				compatible = "fsl,mpc8548-dma-channel",
174						"fsl,eloplus-dma-channel";
175				reg = <0x80 0x80>;
176				cell-index = <1>;
177				interrupt-parent = <&mpic>;
178				interrupts = <21 2>;
179			};
180			dma-channel@100 {
181				compatible = "fsl,mpc8548-dma-channel",
182						"fsl,eloplus-dma-channel";
183				reg = <0x100 0x80>;
184				cell-index = <2>;
185				interrupt-parent = <&mpic>;
186				interrupts = <22 2>;
187			};
188			dma-channel@180 {
189				compatible = "fsl,mpc8548-dma-channel",
190						"fsl,eloplus-dma-channel";
191				reg = <0x180 0x80>;
192				cell-index = <3>;
193				interrupt-parent = <&mpic>;
194				interrupts = <23 2>;
195			};
196		};
197
198		/* eTSEC1: Front panel port 0 */
199		enet0: ethernet@24000 {
200			#address-cells = <1>;
201			#size-cells = <1>;
202			cell-index = <0>;
203			device_type = "network";
204			model = "eTSEC";
205			compatible = "gianfar";
206			reg = <0x24000 0x1000>;
207			ranges = <0x0 0x24000 0x1000>;
208			local-mac-address = [ 00 00 00 00 00 00 ];
209			interrupts = <29 2 30 2 34 2>;
210			interrupt-parent = <&mpic>;
211			tbi-handle = <&tbi0>;
212			phy-handle = <&phy0>;
213
214			mdio@520 {
215				#address-cells = <1>;
216				#size-cells = <0>;
217				compatible = "fsl,gianfar-mdio";
218				reg = <0x520 0x20>;
219
220				phy0: ethernet-phy@1 {
221					interrupt-parent = <&mpic>;
222					interrupts = <8 1>;
223					reg = <0x1>;
224				};
225				phy1: ethernet-phy@2 {
226					interrupt-parent = <&mpic>;
227					interrupts = <8 1>;
228					reg = <0x2>;
229				};
230				phy2: ethernet-phy@3 {
231					interrupt-parent = <&mpic>;
232					interrupts = <8 1>;
233					reg = <0x3>;
234				};
235				phy3: ethernet-phy@4 {
236					interrupt-parent = <&mpic>;
237					interrupts = <8 1>;
238					reg = <0x4>;
239				};
240				tbi0: tbi-phy@11 {
241					reg = <0x11>;
242					device_type = "tbi-phy";
243				};
244			};
245		};
246
247		/* eTSEC2: Front panel port 1 */
248		enet1: ethernet@25000 {
249			#address-cells = <1>;
250			#size-cells = <1>;
251			cell-index = <1>;
252			device_type = "network";
253			model = "eTSEC";
254			compatible = "gianfar";
255			reg = <0x25000 0x1000>;
256			ranges = <0x0 0x25000 0x1000>;
257			local-mac-address = [ 00 00 00 00 00 00 ];
258			interrupts = <35 2 36 2 40 2>;
259			interrupt-parent = <&mpic>;
260			tbi-handle = <&tbi1>;
261			phy-handle = <&phy1>;
262
263			mdio@520 {
264				#address-cells = <1>;
265				#size-cells = <0>;
266				compatible = "fsl,gianfar-tbi";
267				reg = <0x520 0x20>;
268
269				tbi1: tbi-phy@11 {
270					reg = <0x11>;
271					device_type = "tbi-phy";
272				};
273			};
274		};
275
276		/* eTSEC3: Rear panel port 2 */
277		enet2: ethernet@26000 {
278			#address-cells = <1>;
279			#size-cells = <1>;
280			cell-index = <2>;
281			device_type = "network";
282			model = "eTSEC";
283			compatible = "gianfar";
284			reg = <0x26000 0x1000>;
285			ranges = <0x0 0x26000 0x1000>;
286			local-mac-address = [ 00 00 00 00 00 00 ];
287			interrupts = <31 2 32 2 33 2>;
288			interrupt-parent = <&mpic>;
289			tbi-handle = <&tbi2>;
290			phy-handle = <&phy2>;
291
292			mdio@520 {
293				#address-cells = <1>;
294				#size-cells = <0>;
295				compatible = "fsl,gianfar-tbi";
296				reg = <0x520 0x20>;
297
298				tbi2: tbi-phy@11 {
299					reg = <0x11>;
300					device_type = "tbi-phy";
301				};
302			};
303		};
304
305		/* eTSEC4: Rear panel port 3 */
306		enet3: ethernet@27000 {
307			#address-cells = <1>;
308			#size-cells = <1>;
309			cell-index = <3>;
310			device_type = "network";
311			model = "eTSEC";
312			compatible = "gianfar";
313			reg = <0x27000 0x1000>;
314			ranges = <0x0 0x27000 0x1000>;
315			local-mac-address = [ 00 00 00 00 00 00 ];
316			interrupts = <37 2 38 2 39 2>;
317			interrupt-parent = <&mpic>;
318			tbi-handle = <&tbi3>;
319			phy-handle = <&phy3>;
320
321			mdio@520 {
322				#address-cells = <1>;
323				#size-cells = <0>;
324				compatible = "fsl,gianfar-tbi";
325				reg = <0x520 0x20>;
326
327				tbi3: tbi-phy@11 {
328					reg = <0x11>;
329					device_type = "tbi-phy";
330				};
331			};
332		};
333
334		serial0: serial@4500 {
335			cell-index = <0>;
336			device_type = "serial";
337			compatible = "fsl,ns16550", "ns16550";
338			reg = <0x4500 0x100>;
339			clock-frequency = <0>;
340			current-speed = <9600>;
341			interrupts = <42 2>;
342			interrupt-parent = <&mpic>;
343		};
344
345		serial1: serial@4600 {
346			cell-index = <1>;
347			device_type = "serial";
348			compatible = "fsl,ns16550", "ns16550";
349			reg = <0x4600 0x100>;
350			clock-frequency = <0>;
351			current-speed = <9600>;
352			interrupts = <42 2>;
353			interrupt-parent = <&mpic>;
354		};
355
356		global-utilities@e0000 {	// global utilities reg
357			compatible = "fsl,mpc8548-guts";
358			reg = <0xe0000 0x1000>;
359			fsl,has-rstcr;
360		};
361
362		mpic: pic@40000 {
363			interrupt-controller;
364			#address-cells = <0>;
365			#interrupt-cells = <2>;
366			reg = <0x40000 0x40000>;
367			compatible = "chrp,open-pic";
368			device_type = "open-pic";
369		};
370	};
371
372	localbus@ef005000 {
373		compatible = "fsl,mpc8548-localbus", "fsl,pq3-localbus",
374			     "simple-bus";
375		#address-cells = <2>;
376		#size-cells = <1>;
377		reg = <0xef005000 0x100>;	// BRx, ORx, etc.
378		interrupt-parent = <&mpic>;
379		interrupts = <19 2>;
380
381		ranges = <
382			0 0x0 0xf8000000 0x08000000	// NOR boot flash
383			1 0x0 0xf0000000 0x08000000	// NOR expansion flash
384			2 0x0 0xe8000000 0x00010000	// NAND CE1
385			3 0x0 0xe8010000 0x00010000	// NAND CE2
386		>;
387
388		nor-boot@0,0 {
389			#address-cells = <1>;
390			#size-cells = <1>;
391			compatible = "cfi-flash";
392			reg = <0 0x0 0x4000000>;
393			bank-width = <2>;
394
395			partition@0 {
396				label = "Primary OS";
397				reg = <0x00000000 0x180000>;
398			};
399			partition@180000 {
400				label = "Secondary OS";
401				reg = <0x00180000 0x180000>;
402			};
403			partition@300000 {
404				label = "User";
405				reg = <0x00300000 0x3c80000>;
406			};
407			partition@3f80000 {
408				label = "Boot firmware";
409				reg = <0x03f80000 0x80000>;
410			};
411		};
412
413		nor-alternate@1,0 {
414			#address-cells = <1>;
415			#size-cells = <1>;
416			compatible = "cfi-flash";
417			reg = <1 0x0 0x4000000>;
418			bank-width = <2>;
419
420			partition@0 {
421				label = "Filesystem";
422				reg = <0x00000000 0x3f80000>;
423			};
424			partition@3f80000 {
425				label = "Alternate boot firmware";
426				reg = <0x03f80000 0x80000>;
427			};
428		};
429
430		nand@2,0 {
431			#address-cells = <1>;
432			#size-cells = <1>;
433			compatible = "xes,address-ctl-nand";
434			reg = <2 0x0 0x10000>;
435			cle-line = <0x8>;	/* CLE tied to A3 */
436			ale-line = <0x10>;	/* ALE tied to A4 */
437
438			partition@0 {
439				label = "NAND Filesystem";
440				reg = <0 0x40000000>;
441			};
442		};
443	};
444
445	/* PMC interface */
446	pci0: pci@ef008000 {
447		#interrupt-cells = <1>;
448		#size-cells = <2>;
449		#address-cells = <3>;
450		compatible = "fsl,mpc8540-pcix", "fsl,mpc8540-pci";
451		device_type = "pci";
452		reg = <0xef008000 0x1000>;
453		clock-frequency = <33333333>;
454		interrupt-map-mask = <0xf800 0x0 0x0 0x7>;
455		interrupt-map = <
456				/* IDSEL */
457				 0xe000 0 0 1 &mpic 2 1
458				 0xe000 0 0 2 &mpic 3 1>;
459
460		interrupt-parent = <&mpic>;
461		interrupts = <24 2>;
462		bus-range = <0 0>;
463		ranges = <0x02000000 0 0x80000000 0x80000000 0 0x20000000
464			  0x01000000 0 0x00000000 0xd0000000 0 0x01000000>;
465	};
466
467	/* XMC PCIe */
468	pci1: pcie@ef00a000 {
469		interrupt-map-mask = <0xf800 0x0 0x0 0x7>;
470		interrupt-map = <
471			/* IDSEL 0x0 */
472			0x00000 0 0 1 &mpic 0 1
473			0x00000 0 0 2 &mpic 1 1
474			0x00000 0 0 3 &mpic 2 1
475			0x00000 0 0 4 &mpic 3 1>;
476
477		interrupt-parent = <&mpic>;
478		interrupts = <26 2>;
479		bus-range = <0 0xff>;
480		ranges = <0x02000000 0 0xa0000000 0xa0000000 0 0x20000000
481			  0x01000000 0 0x00000000 0xd1000000 0 0x01000000>;
482		clock-frequency = <33333333>;
483		#interrupt-cells = <1>;
484		#size-cells = <2>;
485		#address-cells = <3>;
486		reg = <0xef00a000 0x1000>;
487		compatible = "fsl,mpc8548-pcie";
488		device_type = "pci";
489		pcie@0 {
490			reg = <0 0 0 0 0>;
491			#size-cells = <2>;
492			#address-cells = <3>;
493			device_type = "pci";
494			ranges = <0x02000000 0 0xc0000000 0x02000000 0
495			          0xc0000000 0 0x20000000
496				  0x01000000 0 0x00000000 0x01000000 0
497				  0x00000000 0 0x08000000>;
498		};
499	};
500
501	/* Needed for dtbImage boot wrapper compatibility */
502	chosen {
503		stdout-path = &serial0;
504	};
505};
506