1/* 2 * Copyright (C) 1995, 1996, 1997 Paul M. Antoine and Harald Koerfgen 3 * Copyright (C) 2000, 2001, 2002, 2003, 2005 Maciej W. Rozycki 4 * 5 * Written by Ralf Baechle and Andreas Busse, modified for DECstation 6 * support by Paul Antoine and Harald Koerfgen. 7 * 8 * completely rewritten: 9 * Copyright (C) 1998 Harald Koerfgen 10 * 11 * Rewritten extensively for controller-driven IRQ support 12 * by Maciej W. Rozycki. 13 */ 14 15#include <asm/addrspace.h> 16#include <asm/asm.h> 17#include <asm/mipsregs.h> 18#include <asm/regdef.h> 19#include <asm/stackframe.h> 20 21#include <asm/dec/interrupts.h> 22#include <asm/dec/ioasic_addrs.h> 23#include <asm/dec/ioasic_ints.h> 24#include <asm/dec/kn01.h> 25#include <asm/dec/kn02.h> 26#include <asm/dec/kn02xa.h> 27#include <asm/dec/kn03.h> 28 29#define KN02_CSR_BASE CKSEG1ADDR(KN02_SLOT_BASE + KN02_CSR) 30#define KN02XA_IOASIC_BASE CKSEG1ADDR(KN02XA_SLOT_BASE + IOASIC_IOCTL) 31#define KN03_IOASIC_BASE CKSEG1ADDR(KN03_SLOT_BASE + IOASIC_IOCTL) 32 33 .text 34 .set noreorder 35/* 36 * plat_irq_dispatch: Interrupt handler for DECstations 37 * 38 * We follow the model in the Indy interrupt code by David Miller, where he 39 * says: a lot of complication here is taken away because: 40 * 41 * 1) We handle one interrupt and return, sitting in a loop 42 * and moving across all the pending IRQ bits in the cause 43 * register is _NOT_ the answer, the common case is one 44 * pending IRQ so optimize in that direction. 45 * 46 * 2) We need not check against bits in the status register 47 * IRQ mask, that would make this routine slow as hell. 48 * 49 * 3) Linux only thinks in terms of all IRQs on or all IRQs 50 * off, nothing in between like BSD spl() brain-damage. 51 * 52 * Furthermore, the IRQs on the DECstations look basically (barring 53 * software IRQs which we don't use at all) like... 54 * 55 * DS2100/3100's, aka kn01, aka Pmax: 56 * 57 * MIPS IRQ Source 58 * -------- ------ 59 * 0 Software (ignored) 60 * 1 Software (ignored) 61 * 2 SCSI 62 * 3 Lance Ethernet 63 * 4 DZ11 serial 64 * 5 RTC 65 * 6 Memory Controller & Video 66 * 7 FPU 67 * 68 * DS5000/200, aka kn02, aka 3max: 69 * 70 * MIPS IRQ Source 71 * -------- ------ 72 * 0 Software (ignored) 73 * 1 Software (ignored) 74 * 2 TurboChannel 75 * 3 RTC 76 * 4 Reserved 77 * 5 Memory Controller 78 * 6 Reserved 79 * 7 FPU 80 * 81 * DS5000/1xx's, aka kn02ba, aka 3min: 82 * 83 * MIPS IRQ Source 84 * -------- ------ 85 * 0 Software (ignored) 86 * 1 Software (ignored) 87 * 2 TurboChannel Slot 0 88 * 3 TurboChannel Slot 1 89 * 4 TurboChannel Slot 2 90 * 5 TurboChannel Slot 3 (ASIC) 91 * 6 Halt button 92 * 7 FPU/R4k timer 93 * 94 * DS5000/2x's, aka kn02ca, aka maxine: 95 * 96 * MIPS IRQ Source 97 * -------- ------ 98 * 0 Software (ignored) 99 * 1 Software (ignored) 100 * 2 Periodic Interrupt (100usec) 101 * 3 RTC 102 * 4 I/O write timeout 103 * 5 TurboChannel (ASIC) 104 * 6 Halt Keycode from Access.Bus keyboard (CTRL-ALT-ENTER) 105 * 7 FPU/R4k timer 106 * 107 * DS5000/2xx's, aka kn03, aka 3maxplus: 108 * 109 * MIPS IRQ Source 110 * -------- ------ 111 * 0 Software (ignored) 112 * 1 Software (ignored) 113 * 2 System Board (ASIC) 114 * 3 RTC 115 * 4 Reserved 116 * 5 Memory 117 * 6 Halt Button 118 * 7 FPU/R4k timer 119 * 120 * We handle the IRQ according to _our_ priority (see setup.c), 121 * then we just return. If multiple IRQs are pending then we will 122 * just take another exception, big deal. 123 */ 124 .align 5 125 NESTED(plat_irq_dispatch, PT_SIZE, ra) 126 .set noreorder 127 128 /* 129 * Get pending Interrupts 130 */ 131 mfc0 t0,CP0_CAUSE # get pending interrupts 132 mfc0 t1,CP0_STATUS 133#ifdef CONFIG_32BIT 134 lw t2,cpu_fpu_mask 135#endif 136 andi t0,ST0_IM # CAUSE.CE may be non-zero! 137 and t0,t1 # isolate allowed ones 138 139 beqz t0,spurious 140 141#ifdef CONFIG_32BIT 142 and t2,t0 143 bnez t2,fpu # handle FPU immediately 144#endif 145 146 /* 147 * Find irq with highest priority 148 */ 149 PTR_LA t1,cpu_mask_nr_tbl 1501: lw t2,(t1) 151 nop 152 and t2,t0 153 beqz t2,1b 154 addu t1,2*PTRSIZE # delay slot 155 156 /* 157 * Do the low-level stuff 158 */ 159 lw a0,(-PTRSIZE)(t1) 160 nop 161 bgez a0,handle_it # irq_nr >= 0? 162 # irq_nr < 0: it is an address 163 nop 164 jr a0 165 # a trick to save a branch: 166 lui t2,(KN03_IOASIC_BASE>>16)&0xffff 167 # upper part of IOASIC Address 168 169/* 170 * Handle "IRQ Controller" Interrupts 171 * Masked Interrupts are still visible and have to be masked "by hand". 172 */ 173 FEXPORT(kn02_io_int) # 3max 174 lui t0,(KN02_CSR_BASE>>16)&0xffff 175 # get interrupt status and mask 176 lw t0,(t0) 177 nop 178 andi t1,t0,KN02_IRQ_ALL 179 b 1f 180 srl t0,16 # shift interrupt mask 181 182 FEXPORT(kn02xa_io_int) # 3min/maxine 183 lui t2,(KN02XA_IOASIC_BASE>>16)&0xffff 184 # upper part of IOASIC Address 185 186 FEXPORT(kn03_io_int) # 3max+ (t2 loaded earlier) 187 lw t0,IO_REG_SIR(t2) # get status: IOASIC sir 188 lw t1,IO_REG_SIMR(t2) # get mask: IOASIC simr 189 nop 190 1911: and t0,t1 # mask out allowed ones 192 193 beqz t0,spurious 194 195 /* 196 * Find irq with highest priority 197 */ 198 PTR_LA t1,asic_mask_nr_tbl 1992: lw t2,(t1) 200 nop 201 and t2,t0 202 beq zero,t2,2b 203 addu t1,2*PTRSIZE # delay slot 204 205 /* 206 * Do the low-level stuff 207 */ 208 lw a0,%lo(-PTRSIZE)(t1) 209 nop 210 bgez a0,handle_it # irq_nr >= 0? 211 # irq_nr < 0: it is an address 212 nop 213 jr a0 214 nop # delay slot 215 216/* 217 * Dispatch low-priority interrupts. We reconsider all status 218 * bits again, which looks like a lose, but it makes the code 219 * simple and O(log n), so it gets compensated. 220 */ 221 FEXPORT(cpu_all_int) # HALT, timers, software junk 222 li a0,DEC_CPU_IRQ_BASE 223 srl t0,CAUSEB_IP 224 li t1,CAUSEF_IP>>CAUSEB_IP # mask 225 b 1f 226 li t2,4 # nr of bits / 2 227 228 FEXPORT(kn02_all_int) # impossible ? 229 li a0,KN02_IRQ_BASE 230 li t1,KN02_IRQ_ALL # mask 231 b 1f 232 li t2,4 # nr of bits / 2 233 234 FEXPORT(asic_all_int) # various I/O ASIC junk 235 li a0,IO_IRQ_BASE 236 li t1,IO_IRQ_ALL # mask 237 b 1f 238 li t2,8 # nr of bits / 2 239 240/* 241 * Dispatch DMA interrupts -- O(log n). 242 */ 243 FEXPORT(asic_dma_int) # I/O ASIC DMA events 244 li a0,IO_IRQ_BASE+IO_INR_DMA 245 srl t0,IO_INR_DMA 246 li t1,IO_IRQ_DMA>>IO_INR_DMA # mask 247 li t2,8 # nr of bits / 2 248 249 /* 250 * Find irq with highest priority. 251 * Highest irq number takes precedence. 252 */ 2531: srlv t3,t1,t2 2542: xor t1,t3 255 and t3,t0,t1 256 beqz t3,3f 257 nop 258 move t0,t3 259 addu a0,t2 2603: srl t2,1 261 bnez t2,2b 262 srlv t3,t1,t2 263 264handle_it: 265 j dec_irq_dispatch 266 nop 267 268#ifdef CONFIG_32BIT 269fpu: 270 lw t0,fpu_kstat_irq 271 nop 272 lw t1,(t0) 273 nop 274 addu t1,1 275 j handle_fpe_int 276 sw t1,(t0) 277#endif 278 279spurious: 280 j spurious_interrupt 281 nop 282 END(plat_irq_dispatch) 283 284/* 285 * Generic unimplemented interrupt routines -- cpu_mask_nr_tbl 286 * and asic_mask_nr_tbl are initialized to point all interrupts here. 287 * The tables are then filled in by machine-specific initialisation 288 * in dec_setup(). 289 */ 290 FEXPORT(dec_intr_unimplemented) 291 move a1,t0 # cheats way of printing an arg! 292 PANIC("Unimplemented cpu interrupt! CP0_CAUSE: 0x%08x"); 293 294 FEXPORT(asic_intr_unimplemented) 295 move a1,t0 # cheats way of printing an arg! 296 PANIC("Unimplemented asic interrupt! ASIC ISR: 0x%08x"); 297