1# SPDX-License-Identifier: GPL-2.0-only 2config MICROBLAZE 3 def_bool y 4 select ARCH_32BIT_OFF_T 5 select ARCH_NO_SWAP 6 select ARCH_HAS_DMA_PREP_COHERENT 7 select ARCH_HAS_GCOV_PROFILE_ALL 8 select ARCH_HAS_SYNC_DMA_FOR_CPU 9 select ARCH_HAS_SYNC_DMA_FOR_DEVICE 10 select ARCH_MIGHT_HAVE_PC_PARPORT 11 select ARCH_WANT_IPC_PARSE_VERSION 12 select BUILDTIME_TABLE_SORT 13 select TIMER_OF 14 select CLONE_BACKWARDS3 15 select COMMON_CLK 16 select DMA_DIRECT_REMAP 17 select GENERIC_ATOMIC64 18 select GENERIC_CPU_DEVICES 19 select GENERIC_IDLE_POLL_SETUP 20 select GENERIC_IRQ_PROBE 21 select GENERIC_IRQ_SHOW 22 select GENERIC_PCI_IOMAP 23 select GENERIC_SCHED_CLOCK 24 select HAVE_ARCH_HASH 25 select HAVE_ARCH_KGDB 26 select HAVE_ARCH_SECCOMP 27 select HAVE_DEBUG_KMEMLEAK 28 select HAVE_DMA_CONTIGUOUS 29 select HAVE_DYNAMIC_FTRACE 30 select HAVE_FTRACE_MCOUNT_RECORD 31 select HAVE_FUNCTION_GRAPH_TRACER 32 select HAVE_FUNCTION_TRACER 33 select HAVE_PCI 34 select IRQ_DOMAIN 35 select XILINX_INTC 36 select MODULES_USE_ELF_RELA 37 select OF 38 select OF_EARLY_FLATTREE 39 select PCI_DOMAINS_GENERIC if PCI 40 select PCI_SYSCALL if PCI 41 select VIRT_TO_BUS 42 select CPU_NO_EFFICIENT_FFS 43 select MMU_GATHER_NO_RANGE 44 select SPARSE_IRQ 45 select ZONE_DMA 46 select TRACE_IRQFLAGS_SUPPORT 47 select GENERIC_IRQ_MULTI_HANDLER 48 select HANDLE_DOMAIN_IRQ 49 50# Endianness selection 51choice 52 prompt "Endianness selection" 53 default CPU_LITTLE_ENDIAN 54 help 55 microblaze architectures can be configured for either little or 56 big endian formats. Be sure to select the appropriate mode. 57 58config CPU_BIG_ENDIAN 59 bool "Big endian" 60 61config CPU_LITTLE_ENDIAN 62 bool "Little endian" 63 64endchoice 65 66config ARCH_HAS_ILOG2_U32 67 def_bool n 68 69config ARCH_HAS_ILOG2_U64 70 def_bool n 71 72config GENERIC_HWEIGHT 73 def_bool y 74 75config GENERIC_CALIBRATE_DELAY 76 def_bool y 77 78config GENERIC_CSUM 79 def_bool y 80 81config STACKTRACE_SUPPORT 82 def_bool y 83 84config LOCKDEP_SUPPORT 85 def_bool y 86 87source "arch/microblaze/Kconfig.platform" 88 89menu "Processor type and features" 90 91source "kernel/Kconfig.hz" 92 93config MMU 94 def_bool y 95 96comment "Boot options" 97 98config CMDLINE_BOOL 99 bool "Default bootloader kernel arguments" 100 101config CMDLINE 102 string "Default kernel command string" 103 depends on CMDLINE_BOOL 104 default "console=ttyUL0,115200" 105 help 106 On some architectures there is currently no way for the boot loader 107 to pass arguments to the kernel. For these architectures, you should 108 supply some command-line options at build time by entering them 109 here. 110 111config CMDLINE_FORCE 112 bool "Force default kernel command string" 113 depends on CMDLINE_BOOL 114 default n 115 help 116 Set this to have arguments from the default kernel command string 117 override those passed by the boot loader. 118 119endmenu 120 121menu "Kernel features" 122 123config NR_CPUS 124 int 125 default "1" 126 127config ADVANCED_OPTIONS 128 bool "Prompt for advanced kernel configuration options" 129 help 130 This option will enable prompting for a variety of advanced kernel 131 configuration options. These options can cause the kernel to not 132 work if they are set incorrectly, but can be used to optimize certain 133 aspects of kernel memory management. 134 135 Unless you know what you are doing, say N here. 136 137comment "Default settings for advanced configuration options are used" 138 depends on !ADVANCED_OPTIONS 139 140config HIGHMEM 141 bool "High memory support" 142 select KMAP_LOCAL 143 help 144 The address space of Microblaze processors is only 4 Gigabytes large 145 and it has to accommodate user address space, kernel address 146 space as well as some memory mapped IO. That means that, if you 147 have a large amount of physical memory and/or IO, not all of the 148 memory can be "permanently mapped" by the kernel. The physical 149 memory that is not permanently mapped is called "high memory". 150 151 If unsure, say n. 152 153config LOWMEM_SIZE_BOOL 154 bool "Set maximum low memory" 155 depends on ADVANCED_OPTIONS 156 help 157 This option allows you to set the maximum amount of memory which 158 will be used as "low memory", that is, memory which the kernel can 159 access directly, without having to set up a kernel virtual mapping. 160 This can be useful in optimizing the layout of kernel virtual 161 memory. 162 163 Say N here unless you know what you are doing. 164 165config LOWMEM_SIZE 166 hex "Maximum low memory size (in bytes)" if LOWMEM_SIZE_BOOL 167 default "0x30000000" 168 169config MANUAL_RESET_VECTOR 170 hex "Microblaze reset vector address setup" 171 default "0x0" 172 help 173 Set this option to have the kernel override the CPU Reset vector. 174 If zero, no change will be made to the MicroBlaze reset vector at 175 address 0x0. 176 If non-zero, a jump instruction to this address, will be written 177 to the reset vector at address 0x0. 178 If you are unsure, set it to default value 0x0. 179 180config KERNEL_START_BOOL 181 bool "Set custom kernel base address" 182 depends on ADVANCED_OPTIONS 183 help 184 This option allows you to set the kernel virtual address at which 185 the kernel will map low memory (the kernel image will be linked at 186 this address). This can be useful in optimizing the virtual memory 187 layout of the system. 188 189 Say N here unless you know what you are doing. 190 191config KERNEL_START 192 hex "Virtual address of kernel base" if KERNEL_START_BOOL 193 default "0xc0000000" 194 195config TASK_SIZE_BOOL 196 bool "Set custom user task size" 197 depends on ADVANCED_OPTIONS 198 help 199 This option allows you to set the amount of virtual address space 200 allocated to user tasks. This can be useful in optimizing the 201 virtual memory layout of the system. 202 203 Say N here unless you know what you are doing. 204 205config TASK_SIZE 206 hex "Size of user task space" if TASK_SIZE_BOOL 207 default "0x80000000" 208 209endmenu 210 211menu "Bus Options" 212 213config PCI_XILINX 214 bool "Xilinx PCI host bridge support" 215 depends on PCI 216 217endmenu 218