1 #ifndef _M68K_DELAY_H 2 #define _M68K_DELAY_H 3 4 #include <asm/param.h> 5 6 /* 7 * Copyright (C) 1994 Hamish Macdonald 8 * Copyright (C) 2004 Greg Ungerer <gerg@uclinux.com> 9 * 10 * Delay routines, using a pre-computed "loops_per_jiffy" value. 11 */ 12 13 #if defined(CONFIG_COLDFIRE) 14 /* 15 * The ColdFire runs the delay loop at significantly different speeds 16 * depending upon long word alignment or not. We'll pad it to 17 * long word alignment which is the faster version. 18 * The 0x4a8e is of course a 'tstl %fp' instruction. This is better 19 * than using a NOP (0x4e71) instruction because it executes in one 20 * cycle not three and doesn't allow for an arbitrary delay waiting 21 * for bus cycles to finish. Also fp/a6 isn't likely to cause a 22 * stall waiting for the register to become valid if such is added 23 * to the coldfire at some stage. 24 */ 25 #define DELAY_ALIGN ".balignw 4, 0x4a8e\n\t" 26 #else 27 /* 28 * No instruction alignment required for other m68k types. 29 */ 30 #define DELAY_ALIGN 31 #endif 32 33 static inline void __delay(unsigned long loops) 34 { 35 __asm__ __volatile__ ( 36 DELAY_ALIGN 37 "1: subql #1,%0\n\t" 38 "jcc 1b" 39 : "=d" (loops) 40 : "0" (loops)); 41 } 42 43 extern void __bad_udelay(void); 44 45 46 #ifdef CONFIG_CPU_HAS_NO_MULDIV64 47 /* 48 * The simpler m68k and ColdFire processors do not have a 32*32->64 49 * multiply instruction. So we need to handle them a little differently. 50 * We use a bit of shifting and a single 32*32->32 multiply to get close. 51 * This is a macro so that the const version can factor out the first 52 * multiply and shift. 53 */ 54 #define HZSCALE (268435456 / (1000000 / HZ)) 55 56 #define __const_udelay(u) \ 57 __delay(((((u) * HZSCALE) >> 11) * (loops_per_jiffy >> 11)) >> 6) 58 59 #else 60 61 static inline void __xdelay(unsigned long xloops) 62 { 63 unsigned long tmp; 64 65 __asm__ ("mulul %2,%0:%1" 66 : "=d" (xloops), "=d" (tmp) 67 : "d" (xloops), "1" (loops_per_jiffy)); 68 __delay(xloops * HZ); 69 } 70 71 /* 72 * The definition of __const_udelay is specifically made a macro so that 73 * the const factor (4295 = 2**32 / 1000000) can be optimized out when 74 * the delay is a const. 75 */ 76 #define __const_udelay(n) (__xdelay((n) * 4295)) 77 78 #endif 79 80 static inline void __udelay(unsigned long usecs) 81 { 82 __const_udelay(usecs); 83 } 84 85 /* 86 * Use only for very small delays ( < 1 msec). Should probably use a 87 * lookup table, really, as the multiplications take much too long with 88 * short delays. This is a "reasonable" implementation, though (and the 89 * first constant multiplications gets optimized away if the delay is 90 * a constant) 91 */ 92 #define udelay(n) (__builtin_constant_p(n) ? \ 93 ((n) > 20000 ? __bad_udelay() : __const_udelay(n)) : __udelay(n)) 94 95 96 #endif /* defined(_M68K_DELAY_H) */ 97