1// SPDX-License-Identifier: GPL-2.0+
2/*
3 * dts file for Xilinx ZynqMP zc1751-xm016-dc2
4 *
5 * (C) Copyright 2015 - 2019, Xilinx, Inc.
6 *
7 * Michal Simek <michal.simek@xilinx.com>
8 */
9
10/dts-v1/;
11
12#include "zynqmp.dtsi"
13#include "zynqmp-clk-ccf.dtsi"
14#include <dt-bindings/gpio/gpio.h>
15
16/ {
17	model = "ZynqMP zc1751-xm016-dc2 RevA";
18	compatible = "xlnx,zynqmp-zc1751", "xlnx,zynqmp";
19
20	aliases {
21		can0 = &can0;
22		can1 = &can1;
23		ethernet0 = &gem2;
24		i2c0 = &i2c0;
25		rtc0 = &rtc;
26		serial0 = &uart0;
27		serial1 = &uart1;
28		spi0 = &spi0;
29		spi1 = &spi1;
30	};
31
32	chosen {
33		bootargs = "earlycon";
34		stdout-path = "serial0:115200n8";
35	};
36
37	memory@0 {
38		device_type = "memory";
39		reg = <0x0 0x0 0x0 0x80000000>, <0x8 0x00000000 0x0 0x80000000>;
40	};
41};
42
43&can0 {
44	status = "okay";
45};
46
47&can1 {
48	status = "okay";
49};
50
51&fpd_dma_chan1 {
52	status = "okay";
53};
54
55&fpd_dma_chan2 {
56	status = "okay";
57};
58
59&fpd_dma_chan3 {
60	status = "okay";
61};
62
63&fpd_dma_chan4 {
64	status = "okay";
65};
66
67&fpd_dma_chan5 {
68	status = "okay";
69};
70
71&fpd_dma_chan6 {
72	status = "okay";
73};
74
75&fpd_dma_chan7 {
76	status = "okay";
77};
78
79&fpd_dma_chan8 {
80	status = "okay";
81};
82
83&gem2 {
84	status = "okay";
85	phy-handle = <&phy0>;
86	phy-mode = "rgmii-id";
87	phy0: ethernet-phy@5 {
88		reg = <5>;
89		ti,rx-internal-delay = <0x8>;
90		ti,tx-internal-delay = <0xa>;
91		ti,fifo-depth = <0x1>;
92		ti,dp83867-rxctrl-strap-quirk;
93	};
94};
95
96&gpio {
97	status = "okay";
98};
99
100&i2c0 {
101	status = "okay";
102	clock-frequency = <400000>;
103
104	tca6416_u26: gpio@20 {
105		compatible = "ti,tca6416";
106		reg = <0x20>;
107		gpio-controller;
108		#gpio-cells = <2>;
109		/* IRQ not connected */
110	};
111
112	rtc@68 {
113		compatible = "dallas,ds1339";
114		reg = <0x68>;
115	};
116};
117
118&rtc {
119	status = "okay";
120};
121
122&spi0 {
123	status = "okay";
124	num-cs = <1>;
125
126	spi0_flash0: flash@0 {
127		#address-cells = <1>;
128		#size-cells = <1>;
129		compatible = "sst,sst25wf080", "jedec,spi-nor";
130		spi-max-frequency = <50000000>;
131		reg = <0>;
132
133		partition@0 {
134			label = "data";
135			reg = <0x0 0x100000>;
136		};
137	};
138};
139
140&spi1 {
141	status = "okay";
142	num-cs = <1>;
143
144	spi1_flash0: flash@0 {
145		#address-cells = <1>;
146		#size-cells = <1>;
147		compatible = "atmel,at45db041e", "atmel,at45", "atmel,dataflash";
148		spi-max-frequency = <20000000>;
149		reg = <0>;
150
151		partition@0 {
152			label = "data";
153			reg = <0x0 0x84000>;
154		};
155	};
156};
157
158/* ULPI SMSC USB3320 */
159&usb1 {
160	status = "okay";
161	dr_mode = "host";
162};
163
164&uart0 {
165	status = "okay";
166};
167
168&uart1 {
169	status = "okay";
170};
171