1// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
2/*
3 * Copyright (c) 2017 T-Chip Intelligent Technology Co., Ltd
4 */
5
6/dts-v1/;
7#include <dt-bindings/input/linux-event-codes.h>
8#include <dt-bindings/pwm/pwm.h>
9#include "rk3399.dtsi"
10#include "rk3399-opp.dtsi"
11
12/ {
13	model = "Firefly ROC-RK3399-PC Board";
14	compatible = "firefly,roc-rk3399-pc", "rockchip,rk3399";
15
16	aliases {
17		mmc0 = &sdmmc;
18		mmc1 = &sdhci;
19	};
20
21	chosen {
22		stdout-path = "serial2:1500000n8";
23	};
24
25	backlight: backlight {
26		compatible = "pwm-backlight";
27		pwms = <&pwm0 0 25000 0>;
28	};
29
30	clkin_gmac: external-gmac-clock {
31		compatible = "fixed-clock";
32		clock-frequency = <125000000>;
33		clock-output-names = "clkin_gmac";
34		#clock-cells = <0>;
35	};
36
37	adc-keys {
38		compatible = "adc-keys";
39		io-channels = <&saradc 1>;
40		io-channel-names = "buttons";
41		keyup-threshold-microvolt = <1500000>;
42		poll-interval = <100>;
43
44		button-recovery {
45			label = "Recovery";
46			linux,code = <KEY_VENDOR>;
47			press-threshold-microvolt = <18000>;
48		};
49	};
50
51	gpio-keys {
52		compatible = "gpio-keys";
53		autorepeat;
54		pinctrl-names = "default";
55		pinctrl-0 = <&pwr_key_l>;
56
57		key-power {
58			debounce-interval = <100>;
59			gpios = <&gpio0 RK_PA5 GPIO_ACTIVE_LOW>;
60			label = "GPIO Key Power";
61			linux,code = <KEY_POWER>;
62			wakeup-source;
63		};
64	};
65
66	ir-receiver {
67		compatible = "gpio-ir-receiver";
68		gpios = <&gpio0 RK_PA6 GPIO_ACTIVE_LOW>;
69		pinctrl-names = "default";
70		pinctrl-0 = <&ir_int>;
71	};
72
73	leds {
74		compatible = "gpio-leds";
75		pinctrl-names = "default";
76		pinctrl-0 = <&work_led_pin>, <&diy_led_pin>, <&yellow_led_pin>;
77
78		work_led: led-0 {
79			label = "green:work";
80			gpios = <&gpio2 RK_PD3 GPIO_ACTIVE_HIGH>;
81			default-state = "on";
82			linux,default-trigger = "heartbeat";
83		};
84
85		diy_led: led-1 {
86			label = "red:diy";
87			gpios = <&gpio0 RK_PB5 GPIO_ACTIVE_HIGH>;
88			default-state = "off";
89			linux,default-trigger = "mmc2";
90		};
91
92		yellow_led: led-2 {
93			label = "yellow:yellow-led";
94			gpios = <&gpio0 RK_PA2 GPIO_ACTIVE_HIGH>;
95			default-state = "off";
96			linux,default-trigger = "mmc1";
97		};
98	};
99
100	sdio_pwrseq: sdio-pwrseq {
101		compatible = "mmc-pwrseq-simple";
102		clocks = <&rk808 1>;
103		clock-names = "ext_clock";
104		pinctrl-names = "default";
105		pinctrl-0 = <&wifi_enable_h>;
106
107		/*
108		 * On the module itself this is one of these (depending
109		 * on the actual card populated):
110		 * - SDIO_RESET_L_WL_REG_ON
111		 * - PDN (power down when low)
112		 */
113		reset-gpios = <&gpio0 RK_PB2 GPIO_ACTIVE_LOW>;
114	};
115
116	vcc_vbus_typec0: vcc-vbus-typec0 {
117		compatible = "regulator-fixed";
118		regulator-name = "vcc_vbus_typec0";
119		regulator-always-on;
120		regulator-boot-on;
121		regulator-min-microvolt = <5000000>;
122		regulator-max-microvolt = <5000000>;
123	};
124
125	sys_12v: sys-12v {
126		compatible = "regulator-fixed";
127		regulator-name = "sys_12v";
128		regulator-always-on;
129		regulator-boot-on;
130		vin-supply = <&dc_12v>;
131	};
132
133	/* switched by pmic_sleep */
134	vcc1v8_s3: vcca1v8_s3: vcc1v8-s3 {
135		compatible = "regulator-fixed";
136		regulator-name = "vcc1v8_s3";
137		regulator-always-on;
138		regulator-boot-on;
139		regulator-min-microvolt = <1800000>;
140		regulator-max-microvolt = <1800000>;
141		vin-supply = <&vcc_1v8>;
142	};
143
144	vcc3v0_sd: vcc3v0-sd {
145		compatible = "regulator-fixed";
146		enable-active-high;
147		gpio = <&gpio4 RK_PD6 GPIO_ACTIVE_HIGH>;
148		pinctrl-names = "default";
149		pinctrl-0 = <&vcc3v0_sd_en>;
150		regulator-name = "vcc3v0_sd";
151		regulator-boot-on;
152		regulator-min-microvolt = <3000000>;
153		regulator-max-microvolt = <3000000>;
154		vin-supply = <&vcc3v3_sys>;
155	};
156
157	vcc3v3_sys: vcc3v3-sys {
158		compatible = "regulator-fixed";
159		regulator-name = "vcc3v3_sys";
160		regulator-always-on;
161		regulator-boot-on;
162		regulator-min-microvolt = <3300000>;
163		regulator-max-microvolt = <3300000>;
164		vin-supply = <&sys_12v>;
165	};
166
167	vcca_0v9: vcca-0v9 {
168		compatible = "regulator-fixed";
169		regulator-name = "vcca_0v9";
170		regulator-always-on;
171		regulator-boot-on;
172		regulator-min-microvolt = <900000>;
173		regulator-max-microvolt = <900000>;
174		vin-supply = <&vcc3v3_sys>;
175	};
176
177	/* Actually 3 regulators (host0, 1, 2) controlled by the same gpio */
178	vcc5v0_host: vcc5v0-host-regulator {
179		compatible = "regulator-fixed";
180		enable-active-high;
181		gpio = <&gpio1 RK_PA0 GPIO_ACTIVE_HIGH>;
182		pinctrl-names = "default";
183		pinctrl-0 = <&vcc5v0_host_en &hub_rst>;
184		regulator-name = "vcc5v0_host";
185		vin-supply = <&vcc_sys>;
186	};
187
188	vcc_vbus_typec1: vcc-vbus-typec1 {
189		compatible = "regulator-fixed";
190		enable-active-high;
191		gpio = <&gpio1 RK_PB5 GPIO_ACTIVE_HIGH>;
192		pinctrl-names = "default";
193		pinctrl-0 = <&vcc_vbus_typec1_en>;
194		regulator-name = "vcc_vbus_typec1";
195		regulator-always-on;
196		vin-supply = <&vcc_sys>;
197	};
198
199	vcc_sys: vcc-sys {
200		compatible = "regulator-fixed";
201		enable-active-high;
202		gpio = <&gpio2 RK_PA6 GPIO_ACTIVE_HIGH>;
203		pinctrl-names = "default";
204		pinctrl-0 = <&vcc_sys_en>;
205		regulator-name = "vcc_sys";
206		regulator-boot-on;
207		regulator-min-microvolt = <5000000>;
208		regulator-max-microvolt = <5000000>;
209		vin-supply = <&sys_12v>;
210	};
211
212	vdd_log: vdd-log {
213		compatible = "pwm-regulator";
214		pwms = <&pwm2 0 25000 1>;
215		regulator-name = "vdd_log";
216		regulator-always-on;
217		regulator-boot-on;
218		regulator-min-microvolt = <450000>;
219		regulator-max-microvolt = <1400000>;
220		pwm-supply = <&vcc3v3_sys>;
221	};
222};
223
224&cpu_l0 {
225	cpu-supply = <&vdd_cpu_l>;
226};
227
228&cpu_l1 {
229	cpu-supply = <&vdd_cpu_l>;
230};
231
232&cpu_l2 {
233	cpu-supply = <&vdd_cpu_l>;
234};
235
236&cpu_l3 {
237	cpu-supply = <&vdd_cpu_l>;
238};
239
240&cpu_b0 {
241	cpu-supply = <&vdd_cpu_b>;
242};
243
244&cpu_b1 {
245	cpu-supply = <&vdd_cpu_b>;
246};
247
248&emmc_phy {
249	status = "okay";
250};
251
252&gmac {
253	assigned-clocks = <&cru SCLK_RMII_SRC>;
254	assigned-clock-parents = <&clkin_gmac>;
255	clock_in_out = "input";
256	phy-supply = <&vcc_lan>;
257	phy-mode = "rgmii";
258	pinctrl-names = "default";
259	pinctrl-0 = <&rgmii_pins>;
260	snps,reset-gpio = <&gpio3 RK_PB7 GPIO_ACTIVE_LOW>;
261	snps,reset-active-low;
262	snps,reset-delays-us = <0 10000 50000>;
263	tx_delay = <0x28>;
264	rx_delay = <0x11>;
265	status = "okay";
266};
267
268&gpu {
269	mali-supply = <&vdd_gpu>;
270	status = "okay";
271};
272
273&hdmi {
274	avdd-0v9-supply = <&vcca0v9_hdmi>;
275	avdd-1v8-supply = <&vcca1v8_hdmi>;
276	ddc-i2c-bus = <&i2c3>;
277	pinctrl-names = "default";
278	pinctrl-0 = <&hdmi_cec>;
279	status = "okay";
280};
281
282&hdmi_sound {
283	status = "okay";
284};
285
286&i2c0 {
287	clock-frequency = <400000>;
288	i2c-scl-rising-time-ns = <168>;
289	i2c-scl-falling-time-ns = <4>;
290	status = "okay";
291
292	rk808: pmic@1b {
293		compatible = "rockchip,rk808";
294		reg = <0x1b>;
295		interrupt-parent = <&gpio1>;
296		interrupts = <21 IRQ_TYPE_LEVEL_LOW>;
297		#clock-cells = <1>;
298		clock-output-names = "xin32k", "rk808-clkout2";
299		pinctrl-names = "default";
300		pinctrl-0 = <&pmic_int_l>;
301		rockchip,system-power-controller;
302		wakeup-source;
303
304		vcc1-supply = <&vcc3v3_sys>;
305		vcc2-supply = <&vcc3v3_sys>;
306		vcc3-supply = <&vcc3v3_sys>;
307		vcc4-supply = <&vcc3v3_sys>;
308		vcc6-supply = <&vcc3v3_sys>;
309		vcc7-supply = <&vcc3v3_sys>;
310		vcc8-supply = <&vcc3v3_sys>;
311		vcc9-supply = <&vcc3v3_sys>;
312		vcc10-supply = <&vcc3v3_sys>;
313		vcc11-supply = <&vcc3v3_sys>;
314		vcc12-supply = <&vcc3v3_sys>;
315		vddio-supply = <&vcc_3v0>;
316
317		regulators {
318			vdd_center: DCDC_REG1 {
319				regulator-name = "vdd_center";
320				regulator-always-on;
321				regulator-boot-on;
322				regulator-min-microvolt = <750000>;
323				regulator-max-microvolt = <1350000>;
324				regulator-ramp-delay = <6001>;
325				regulator-state-mem {
326					regulator-off-in-suspend;
327				};
328			};
329
330			vdd_cpu_l: DCDC_REG2 {
331				regulator-name = "vdd_cpu_l";
332				regulator-always-on;
333				regulator-boot-on;
334				regulator-min-microvolt = <750000>;
335				regulator-max-microvolt = <1350000>;
336				regulator-ramp-delay = <6001>;
337				regulator-state-mem {
338					regulator-off-in-suspend;
339				};
340			};
341
342			vcc_ddr: DCDC_REG3 {
343				regulator-name = "vcc_ddr";
344				regulator-always-on;
345				regulator-boot-on;
346				regulator-state-mem {
347					regulator-on-in-suspend;
348				};
349			};
350
351			vcc_1v8: DCDC_REG4 {
352				regulator-name = "vcc_1v8";
353				regulator-always-on;
354				regulator-boot-on;
355				regulator-min-microvolt = <1800000>;
356				regulator-max-microvolt = <1800000>;
357				regulator-state-mem {
358					regulator-on-in-suspend;
359					regulator-suspend-microvolt = <1800000>;
360				};
361			};
362
363			vcca1v8_codec: LDO_REG1 {
364				regulator-name = "vcca1v8_codec";
365				regulator-always-on;
366				regulator-boot-on;
367				regulator-min-microvolt = <1800000>;
368				regulator-max-microvolt = <1800000>;
369				regulator-state-mem {
370					regulator-off-in-suspend;
371				};
372			};
373
374			vcca1v8_hdmi: LDO_REG2 {
375				regulator-name = "vcca1v8_hdmi";
376				regulator-always-on;
377				regulator-boot-on;
378				regulator-min-microvolt = <1800000>;
379				regulator-max-microvolt = <1800000>;
380				regulator-state-mem {
381					regulator-off-in-suspend;
382				};
383			};
384
385			vcc1v8_pmu: LDO_REG3 {
386				regulator-name = "vcc1v8_pmu";
387				regulator-always-on;
388				regulator-boot-on;
389				regulator-min-microvolt = <1800000>;
390				regulator-max-microvolt = <1800000>;
391				regulator-state-mem {
392					regulator-on-in-suspend;
393					regulator-suspend-microvolt = <1800000>;
394				};
395			};
396
397			vcc_sdio: LDO_REG4 {
398				regulator-name = "vcc_sdio";
399				regulator-always-on;
400				regulator-boot-on;
401				regulator-min-microvolt = <1800000>;
402				regulator-max-microvolt = <3000000>;
403				regulator-state-mem {
404					regulator-on-in-suspend;
405					regulator-suspend-microvolt = <3000000>;
406				};
407			};
408
409			vcca3v0_codec: LDO_REG5 {
410				regulator-name = "vcca3v0_codec";
411				regulator-always-on;
412				regulator-boot-on;
413				regulator-min-microvolt = <3000000>;
414				regulator-max-microvolt = <3000000>;
415				regulator-state-mem {
416					regulator-off-in-suspend;
417				};
418			};
419
420			vcc_1v5: LDO_REG6 {
421				regulator-name = "vcc_1v5";
422				regulator-always-on;
423				regulator-boot-on;
424				regulator-min-microvolt = <1500000>;
425				regulator-max-microvolt = <1500000>;
426				regulator-state-mem {
427					regulator-on-in-suspend;
428					regulator-suspend-microvolt = <1500000>;
429				};
430			};
431
432			vcca0v9_hdmi: LDO_REG7 {
433				regulator-name = "vcca0v9_hdmi";
434				regulator-always-on;
435				regulator-boot-on;
436				regulator-min-microvolt = <900000>;
437				regulator-max-microvolt = <900000>;
438				regulator-state-mem {
439					regulator-off-in-suspend;
440				};
441			};
442
443			vcc_3v0: LDO_REG8 {
444				regulator-name = "vcc_3v0";
445				regulator-always-on;
446				regulator-boot-on;
447				regulator-min-microvolt = <3000000>;
448				regulator-max-microvolt = <3000000>;
449				regulator-state-mem {
450					regulator-on-in-suspend;
451					regulator-suspend-microvolt = <3000000>;
452				};
453			};
454
455			vcc3v3_s3: vcc_lan: SWITCH_REG1 {
456				regulator-name = "vcc3v3_s3";
457				regulator-always-on;
458				regulator-boot-on;
459				regulator-state-mem {
460					regulator-off-in-suspend;
461				};
462			};
463
464			vcc3v3_s0: SWITCH_REG2 {
465				regulator-name = "vcc3v3_s0";
466				regulator-always-on;
467				regulator-boot-on;
468				regulator-state-mem {
469					regulator-off-in-suspend;
470				};
471			};
472		};
473	};
474
475	vdd_cpu_b: regulator@40 {
476		compatible = "silergy,syr827";
477		reg = <0x40>;
478		fcs,suspend-voltage-selector = <1>;
479		pinctrl-names = "default";
480		pinctrl-0 = <&vsel1_pin>;
481		regulator-name = "vdd_cpu_b";
482		regulator-min-microvolt = <712500>;
483		regulator-max-microvolt = <1500000>;
484		regulator-ramp-delay = <1000>;
485		regulator-always-on;
486		regulator-boot-on;
487		vin-supply = <&vcc3v3_sys>;
488
489		regulator-state-mem {
490			regulator-off-in-suspend;
491		};
492	};
493
494	vdd_gpu: regulator@41 {
495		compatible = "silergy,syr828";
496		reg = <0x41>;
497		fcs,suspend-voltage-selector = <1>;
498		pinctrl-names = "default";
499		pinctrl-0 = <&vsel2_pin>;
500		regulator-name = "vdd_gpu";
501		regulator-min-microvolt = <712500>;
502		regulator-max-microvolt = <1500000>;
503		regulator-ramp-delay = <1000>;
504		regulator-always-on;
505		regulator-boot-on;
506		vin-supply = <&vcc3v3_sys>;
507
508		regulator-state-mem {
509			regulator-off-in-suspend;
510		};
511	};
512};
513
514&i2c1 {
515	i2c-scl-rising-time-ns = <300>;
516	i2c-scl-falling-time-ns = <15>;
517	status = "okay";
518};
519
520&i2c3 {
521	i2c-scl-rising-time-ns = <450>;
522	i2c-scl-falling-time-ns = <15>;
523	status = "okay";
524};
525
526&i2c4 {
527	i2c-scl-rising-time-ns = <600>;
528	i2c-scl-falling-time-ns = <20>;
529	status = "okay";
530
531	fusb1: usb-typec@22 {
532		compatible = "fcs,fusb302";
533		reg = <0x22>;
534		interrupt-parent = <&gpio1>;
535		interrupts = <1 IRQ_TYPE_LEVEL_LOW>;
536		pinctrl-names = "default";
537		pinctrl-0 = <&fusb1_int>;
538		vbus-supply = <&vcc_vbus_typec1>;
539		status = "okay";
540	};
541};
542
543&i2c7 {
544	i2c-scl-rising-time-ns = <600>;
545	i2c-scl-falling-time-ns = <20>;
546	status = "okay";
547
548	fusb0: usb-typec@22 {
549		compatible = "fcs,fusb302";
550		reg = <0x22>;
551		interrupt-parent = <&gpio1>;
552		interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
553		pinctrl-names = "default";
554		pinctrl-0 = <&fusb0_int>;
555		vbus-supply = <&vcc_vbus_typec0>;
556		status = "okay";
557	};
558
559	mp8859: regulator@66 {
560		compatible = "mps,mp8859";
561		reg = <0x66>;
562		dc_12v: mp8859_dcdc {
563			regulator-name = "dc_12v";
564			regulator-min-microvolt = <12000000>;
565			regulator-max-microvolt = <12000000>;
566			regulator-always-on;
567			regulator-boot-on;
568			vin-supply = <&vcc_vbus_typec0>;
569
570			regulator-state-mem {
571				regulator-on-in-suspend;
572				regulator-suspend-microvolt = <12000000>;
573			};
574		};
575	};
576};
577
578&i2s0 {
579	rockchip,playback-channels = <8>;
580	rockchip,capture-channels = <8>;
581	status = "okay";
582};
583
584&i2s1 {
585	rockchip,playback-channels = <2>;
586	rockchip,capture-channels = <2>;
587	status = "okay";
588};
589
590&i2s2 {
591	status = "okay";
592};
593
594&io_domains {
595	audio-supply = <&vcca1v8_codec>;
596	bt656-supply = <&vcc_3v0>;
597	gpio1830-supply = <&vcc_3v0>;
598	sdmmc-supply = <&vcc_sdio>;
599	status = "okay";
600};
601
602&pmu_io_domains {
603	pmu1830-supply = <&vcc_3v0>;
604	status = "okay";
605};
606
607&pinctrl {
608	buttons {
609		pwr_key_l: pwr-key-l {
610			rockchip,pins = <0 RK_PA5 RK_FUNC_GPIO &pcfg_pull_up>;
611		};
612	};
613
614	ir {
615		ir_int: ir-int {
616			rockchip,pins = <0 RK_PA6 RK_FUNC_GPIO &pcfg_pull_none>;
617		};
618	};
619
620	lcd-panel {
621		lcd_panel_reset: lcd-panel-reset {
622			rockchip,pins = <4 RK_PD5 RK_FUNC_GPIO &pcfg_pull_up>;
623		};
624	};
625
626	leds {
627		diy_led_pin: diy-led-pin {
628			rockchip,pins = <0 RK_PB5 RK_FUNC_GPIO &pcfg_pull_none>;
629		};
630
631		work_led_pin: work-led-pin {
632			rockchip,pins = <2 RK_PD3 RK_FUNC_GPIO &pcfg_pull_none>;
633		};
634
635		yellow_led_pin: yellow-led-pin {
636			rockchip,pins = <0 RK_PA2 RK_FUNC_GPIO &pcfg_pull_none>;
637		};
638	};
639
640	pmic {
641		vsel1_pin: vsel1-pin {
642			rockchip,pins = <1 RK_PC2 RK_FUNC_GPIO &pcfg_pull_down>;
643		};
644
645		vsel2_pin: vsel2-pin {
646			rockchip,pins = <1 RK_PB6 RK_FUNC_GPIO &pcfg_pull_down>;
647		};
648	};
649
650	sdio-pwrseq {
651		wifi_enable_h: wifi-enable-h {
652			rockchip,pins = <0 RK_PB2 RK_FUNC_GPIO &pcfg_pull_none>;
653		};
654	};
655
656	sdmmc {
657		vcc3v0_sd_en: vcc3v0-sd-en {
658			rockchip,pins = <4 RK_PD6 RK_FUNC_GPIO &pcfg_pull_none>;
659		};
660	};
661
662	pmic {
663		pmic_int_l: pmic-int-l {
664			rockchip,pins = <1 RK_PC5 RK_FUNC_GPIO &pcfg_pull_up>;
665		};
666	};
667
668	usb2 {
669		vcc5v0_host_en: vcc5v0-host-en {
670			rockchip,pins = <1 RK_PA0 RK_FUNC_GPIO &pcfg_pull_none>;
671		};
672
673		vcc_sys_en: vcc-sys-en {
674			rockchip,pins = <2 RK_PA6 RK_FUNC_GPIO &pcfg_pull_none>;
675		};
676
677		hub_rst: hub-rst {
678			rockchip,pins = <2 RK_PA4 RK_FUNC_GPIO &pcfg_output_high>;
679		};
680	};
681
682	usb-typec {
683		vcc_vbus_typec1_en: vcc-vbus-typec1-en {
684			rockchip,pins = <1 RK_PB5 RK_FUNC_GPIO &pcfg_pull_none>;
685		};
686	};
687
688	fusb30x {
689		fusb0_int: fusb0-int {
690			rockchip,pins = <1 RK_PA2 RK_FUNC_GPIO &pcfg_pull_up>;
691		};
692
693		fusb1_int: fusb1-int {
694			rockchip,pins = <1 RK_PA1 RK_FUNC_GPIO &pcfg_pull_up>;
695		};
696	};
697};
698
699&pwm0 {
700	status = "okay";
701};
702
703&pwm2 {
704	status = "okay";
705};
706
707&saradc {
708	vref-supply = <&vcca1v8_s3>;
709	status = "okay";
710};
711
712&sdmmc {
713	bus-width = <4>;
714	cap-sd-highspeed;
715	cd-gpios = <&gpio0 RK_PA7 GPIO_ACTIVE_LOW>;
716	disable-wp;
717	max-frequency = <150000000>;
718	pinctrl-names = "default";
719	pinctrl-0 = <&sdmmc_clk &sdmmc_cmd &sdmmc_bus4>;
720	sd-uhs-sdr104;
721	vmmc-supply = <&vcc3v0_sd>;
722	vqmmc-supply = <&vcc_sdio>;
723	status = "okay";
724};
725
726&sdhci {
727	bus-width = <8>;
728	non-removable;
729	status = "okay";
730};
731
732&spi1 {
733	status = "okay";
734
735	flash@0 {
736		compatible = "jedec,spi-nor";
737		reg = <0>;
738		spi-max-frequency = <10000000>;
739	};
740};
741
742&tcphy0 {
743	status = "okay";
744};
745
746&tcphy1 {
747	status = "okay";
748};
749
750&tsadc {
751	/* tshut mode 0:CRU 1:GPIO */
752	rockchip,hw-tshut-mode = <1>;
753	/* tshut polarity 0:LOW 1:HIGH */
754	rockchip,hw-tshut-polarity = <1>;
755	status = "okay";
756};
757
758&u2phy0 {
759	status = "okay";
760
761	u2phy0_otg: otg-port {
762		phy-supply = <&vcc_vbus_typec0>;
763		status = "okay";
764	};
765
766	u2phy0_host: host-port {
767		phy-supply = <&vcc5v0_host>;
768		status = "okay";
769	};
770};
771
772&u2phy1 {
773	status = "okay";
774
775	u2phy1_otg: otg-port {
776		phy-supply = <&vcc_vbus_typec1>;
777		status = "okay";
778	};
779
780	u2phy1_host: host-port {
781		phy-supply = <&vcc5v0_host>;
782		status = "okay";
783	};
784};
785
786&uart0 {
787	pinctrl-names = "default";
788	pinctrl-0 = <&uart0_xfer &uart0_cts>;
789	status = "okay";
790};
791
792&uart2 {
793	status = "okay";
794};
795
796&usb_host0_ehci {
797	status = "okay";
798};
799
800&usb_host0_ohci {
801	status = "okay";
802};
803
804&usb_host1_ehci {
805	status = "okay";
806};
807
808&usb_host1_ohci {
809	status = "okay";
810};
811
812&usbdrd3_0 {
813	status = "okay";
814};
815
816&usbdrd_dwc3_0 {
817	status = "okay";
818};
819
820&usbdrd3_1 {
821	status = "okay";
822};
823
824&usbdrd_dwc3_1 {
825	status = "okay";
826	dr_mode = "host";
827};
828
829&vopb {
830	status = "okay";
831};
832
833&vopb_mmu {
834	status = "okay";
835};
836
837&vopl {
838	status = "okay";
839};
840
841&vopl_mmu {
842	status = "okay";
843};
844