1// SPDX-License-Identifier: GPL-2.0
2/*
3 * Device Tree Source for common parts of Salvator-X board variants
4 *
5 * Copyright (C) 2015-2016 Renesas Electronics Corp.
6 */
7
8/*
9 * SSI-AK4613
10 *
11 * This command is required when Playback/Capture
12 *
13 *	amixer set "DVC Out" 100%
14 *	amixer set "DVC In" 100%
15 *
16 * You can use Mute
17 *
18 *	amixer set "DVC Out Mute" on
19 *	amixer set "DVC In Mute" on
20 *
21 * You can use Volume Ramp
22 *
23 *	amixer set "DVC Out Ramp Up Rate"   "0.125 dB/64 steps"
24 *	amixer set "DVC Out Ramp Down Rate" "0.125 dB/512 steps"
25 *	amixer set "DVC Out Ramp" on
26 *	aplay xxx.wav &
27 *	amixer set "DVC Out"  80%  // Volume Down
28 *	amixer set "DVC Out" 100%  // Volume Up
29 */
30
31#include <dt-bindings/gpio/gpio.h>
32#include <dt-bindings/input/input.h>
33
34/ {
35	aliases {
36		serial0 = &scif2;
37		serial1 = &hscif1;
38		ethernet0 = &avb;
39	};
40
41	chosen {
42		bootargs = "ignore_loglevel rw root=/dev/nfs ip=on";
43		stdout-path = "serial0:115200n8";
44	};
45
46	audio_clkout: audio-clkout {
47		/*
48		 * This is same as <&rcar_sound 0>
49		 * but needed to avoid cs2000/rcar_sound probe dead-lock
50		 */
51		compatible = "fixed-clock";
52		#clock-cells = <0>;
53		clock-frequency = <12288000>;
54	};
55
56	backlight: backlight {
57		compatible = "pwm-backlight";
58		pwms = <&pwm1 0 50000>;
59
60		brightness-levels = <256 128 64 16 8 4 0>;
61		default-brightness-level = <6>;
62
63		power-supply = <&reg_12v>;
64		enable-gpios = <&gpio6 7 GPIO_ACTIVE_HIGH>;
65	};
66
67	cvbs-in {
68		compatible = "composite-video-connector";
69		label = "CVBS IN";
70
71		port {
72			cvbs_con: endpoint {
73				remote-endpoint = <&adv7482_ain7>;
74			};
75		};
76	};
77
78	hdmi-in {
79		compatible = "hdmi-connector";
80		label = "HDMI IN";
81		type = "a";
82
83		port {
84			hdmi_in_con: endpoint {
85				remote-endpoint = <&adv7482_hdmi>;
86			};
87		};
88	};
89
90	keys {
91		compatible = "gpio-keys";
92
93		pinctrl-0 = <&keys_pins>;
94		pinctrl-names = "default";
95
96		key-1 {
97			gpios = <&gpio5 17 GPIO_ACTIVE_LOW>;
98			linux,code = <KEY_1>;
99			label = "SW4-1";
100			wakeup-source;
101			debounce-interval = <20>;
102		};
103		key-2 {
104			gpios = <&gpio5 20 GPIO_ACTIVE_LOW>;
105			linux,code = <KEY_2>;
106			label = "SW4-2";
107			wakeup-source;
108			debounce-interval = <20>;
109		};
110		key-3 {
111			gpios = <&gpio5 22 GPIO_ACTIVE_LOW>;
112			linux,code = <KEY_3>;
113			label = "SW4-3";
114			wakeup-source;
115			debounce-interval = <20>;
116		};
117		key-4 {
118			gpios = <&gpio5 23 GPIO_ACTIVE_LOW>;
119			linux,code = <KEY_4>;
120			label = "SW4-4";
121			wakeup-source;
122			debounce-interval = <20>;
123		};
124		key-a {
125			gpios = <&gpio6 11 GPIO_ACTIVE_LOW>;
126			linux,code = <KEY_A>;
127			label = "TSW0";
128			wakeup-source;
129			debounce-interval = <20>;
130		};
131		key-b {
132			gpios = <&gpio6 12 GPIO_ACTIVE_LOW>;
133			linux,code = <KEY_B>;
134			label = "TSW1";
135			wakeup-source;
136			debounce-interval = <20>;
137		};
138		key-c {
139			gpios = <&gpio6 13 GPIO_ACTIVE_LOW>;
140			linux,code = <KEY_C>;
141			label = "TSW2";
142			wakeup-source;
143			debounce-interval = <20>;
144		};
145	};
146
147	reg_1p8v: regulator0 {
148		compatible = "regulator-fixed";
149		regulator-name = "fixed-1.8V";
150		regulator-min-microvolt = <1800000>;
151		regulator-max-microvolt = <1800000>;
152		regulator-boot-on;
153		regulator-always-on;
154	};
155
156	reg_3p3v: regulator1 {
157		compatible = "regulator-fixed";
158		regulator-name = "fixed-3.3V";
159		regulator-min-microvolt = <3300000>;
160		regulator-max-microvolt = <3300000>;
161		regulator-boot-on;
162		regulator-always-on;
163	};
164
165	reg_12v: regulator2 {
166		compatible = "regulator-fixed";
167		regulator-name = "fixed-12V";
168		regulator-min-microvolt = <12000000>;
169		regulator-max-microvolt = <12000000>;
170		regulator-boot-on;
171		regulator-always-on;
172	};
173
174	sound_card: sound {
175		compatible = "audio-graph-card";
176
177		label = "rcar-sound";
178
179		dais = <&rsnd_port0>;
180	};
181
182	vbus0_usb2: regulator-vbus0-usb2 {
183		compatible = "regulator-fixed";
184
185		regulator-name = "USB20_VBUS0";
186		regulator-min-microvolt = <5000000>;
187		regulator-max-microvolt = <5000000>;
188
189		gpio = <&gpio6 16 GPIO_ACTIVE_HIGH>;
190		enable-active-high;
191	};
192
193	vcc_sdhi0: regulator-vcc-sdhi0 {
194		compatible = "regulator-fixed";
195
196		regulator-name = "SDHI0 Vcc";
197		regulator-min-microvolt = <3300000>;
198		regulator-max-microvolt = <3300000>;
199
200		gpio = <&gpio5 2 GPIO_ACTIVE_HIGH>;
201		enable-active-high;
202	};
203
204	vccq_sdhi0: regulator-vccq-sdhi0 {
205		compatible = "regulator-gpio";
206
207		regulator-name = "SDHI0 VccQ";
208		regulator-min-microvolt = <1800000>;
209		regulator-max-microvolt = <3300000>;
210
211		gpios = <&gpio5 1 GPIO_ACTIVE_HIGH>;
212		gpios-states = <1>;
213		states = <3300000 1
214			  1800000 0>;
215	};
216
217	vcc_sdhi3: regulator-vcc-sdhi3 {
218		compatible = "regulator-fixed";
219
220		regulator-name = "SDHI3 Vcc";
221		regulator-min-microvolt = <3300000>;
222		regulator-max-microvolt = <3300000>;
223
224		gpio = <&gpio3 15 GPIO_ACTIVE_HIGH>;
225		enable-active-high;
226	};
227
228	vccq_sdhi3: regulator-vccq-sdhi3 {
229		compatible = "regulator-gpio";
230
231		regulator-name = "SDHI3 VccQ";
232		regulator-min-microvolt = <1800000>;
233		regulator-max-microvolt = <3300000>;
234
235		gpios = <&gpio3 14 GPIO_ACTIVE_HIGH>;
236		gpios-states = <1>;
237		states = <3300000 1
238			  1800000 0>;
239	};
240
241	hdmi0-out {
242		compatible = "hdmi-connector";
243		label = "HDMI0 OUT";
244		type = "a";
245
246		port {
247			hdmi0_con: endpoint {
248			};
249		};
250	};
251
252	hdmi1-out {
253		compatible = "hdmi-connector";
254		label = "HDMI1 OUT";
255		type = "a";
256
257		port {
258			hdmi1_con: endpoint {
259			};
260		};
261	};
262
263	vga {
264		compatible = "vga-connector";
265
266		port {
267			vga_in: endpoint {
268				remote-endpoint = <&adv7123_out>;
269			};
270		};
271	};
272
273	vga-encoder {
274		compatible = "adi,adv7123";
275
276		ports {
277			#address-cells = <1>;
278			#size-cells = <0>;
279
280			port@0 {
281				reg = <0>;
282				adv7123_in: endpoint {
283					remote-endpoint = <&du_out_rgb>;
284				};
285			};
286			port@1 {
287				reg = <1>;
288				adv7123_out: endpoint {
289					remote-endpoint = <&vga_in>;
290				};
291			};
292		};
293	};
294
295	x12_clk: x12 {
296		compatible = "fixed-clock";
297		#clock-cells = <0>;
298		clock-frequency = <24576000>;
299	};
300
301	/* External DU dot clocks */
302	x21_clk: x21-clock {
303		compatible = "fixed-clock";
304		#clock-cells = <0>;
305		clock-frequency = <33000000>;
306	};
307
308	x22_clk: x22-clock {
309		compatible = "fixed-clock";
310		#clock-cells = <0>;
311		clock-frequency = <33000000>;
312	};
313
314	x23_clk: x23-clock {
315		compatible = "fixed-clock";
316		#clock-cells = <0>;
317		clock-frequency = <25000000>;
318	};
319};
320
321&audio_clk_a {
322	clock-frequency = <22579200>;
323};
324
325&avb {
326	pinctrl-0 = <&avb_pins>;
327	pinctrl-names = "default";
328	phy-handle = <&phy0>;
329	phy-mode = "rgmii-txid";
330	status = "okay";
331
332	phy0: ethernet-phy@0 {
333		rxc-skew-ps = <1500>;
334		reg = <0>;
335		interrupt-parent = <&gpio2>;
336		interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
337		reset-gpios = <&gpio2 10 GPIO_ACTIVE_LOW>;
338	};
339};
340
341&csi20 {
342	status = "okay";
343
344	ports {
345		port@0 {
346			reg = <0>;
347			csi20_in: endpoint {
348				clock-lanes = <0>;
349				data-lanes = <1>;
350				remote-endpoint = <&adv7482_txb>;
351			};
352		};
353	};
354};
355
356&csi40 {
357	status = "okay";
358
359	ports {
360		port@0 {
361			reg = <0>;
362
363			csi40_in: endpoint {
364				clock-lanes = <0>;
365				data-lanes = <1 2 3 4>;
366				remote-endpoint = <&adv7482_txa>;
367			};
368		};
369	};
370};
371
372&du {
373	pinctrl-0 = <&du_pins>;
374	pinctrl-names = "default";
375	status = "okay";
376
377	ports {
378		port@0 {
379			endpoint {
380				remote-endpoint = <&adv7123_in>;
381			};
382		};
383	};
384};
385
386&ehci0 {
387	dr_mode = "otg";
388	status = "okay";
389};
390
391&ehci1 {
392	status = "okay";
393};
394
395&extalr_clk {
396	clock-frequency = <32768>;
397};
398
399&hscif1 {
400	pinctrl-0 = <&hscif1_pins>;
401	pinctrl-names = "default";
402
403	uart-has-rtscts;
404	/* Please only enable hscif1 or scif1 */
405	status = "okay";
406};
407
408&hsusb {
409	dr_mode = "otg";
410	status = "okay";
411};
412
413&i2c2 {
414	pinctrl-0 = <&i2c2_pins>;
415	pinctrl-names = "default";
416
417	status = "okay";
418
419	clock-frequency = <100000>;
420
421	ak4613: codec@10 {
422		compatible = "asahi-kasei,ak4613";
423		#sound-dai-cells = <0>;
424		reg = <0x10>;
425		clocks = <&rcar_sound 3>;
426
427		asahi-kasei,in1-single-end;
428		asahi-kasei,in2-single-end;
429		asahi-kasei,out1-single-end;
430		asahi-kasei,out2-single-end;
431		asahi-kasei,out3-single-end;
432		asahi-kasei,out4-single-end;
433		asahi-kasei,out5-single-end;
434		asahi-kasei,out6-single-end;
435
436		port {
437			ak4613_endpoint: endpoint {
438				remote-endpoint = <&rsnd_endpoint0>;
439			};
440		};
441	};
442
443	cs2000: clk_multiplier@4f {
444		#clock-cells = <0>;
445		compatible = "cirrus,cs2000-cp";
446		reg = <0x4f>;
447		clocks = <&audio_clkout>, <&x12_clk>;
448		clock-names = "clk_in", "ref_clk";
449
450		assigned-clocks = <&cs2000>;
451		assigned-clock-rates = <24576000>; /* 1/1 divide */
452	};
453};
454
455&i2c4 {
456	status = "okay";
457
458	pca9654: gpio@20 {
459		compatible = "onnn,pca9654";
460		reg = <0x20>;
461		gpio-controller;
462		#gpio-cells = <2>;
463	};
464
465	csa_vdd: adc@7c {
466		compatible = "maxim,max9611";
467		reg = <0x7c>;
468
469		shunt-resistor-micro-ohms = <5000>;
470	};
471
472	csa_dvfs: adc@7f {
473		compatible = "maxim,max9611";
474		reg = <0x7f>;
475
476		shunt-resistor-micro-ohms = <5000>;
477	};
478
479	video-receiver@70 {
480		compatible = "adi,adv7482";
481		reg = <0x70 0x71 0x72 0x73 0x74 0x75
482		       0x60 0x61 0x62 0x63 0x64 0x65>;
483		reg-names = "main", "dpll", "cp", "hdmi", "edid", "repeater",
484			    "infoframe", "cbus", "cec", "sdp", "txa", "txb" ;
485
486		#address-cells = <1>;
487		#size-cells = <0>;
488
489		interrupt-parent = <&gpio6>;
490		interrupt-names = "intrq1", "intrq2";
491		interrupts = <30 IRQ_TYPE_LEVEL_LOW>,
492			     <31 IRQ_TYPE_LEVEL_LOW>;
493
494		port@7 {
495			reg = <7>;
496
497			adv7482_ain7: endpoint {
498				remote-endpoint = <&cvbs_con>;
499			};
500		};
501
502		port@8 {
503			reg = <8>;
504
505			adv7482_hdmi: endpoint {
506				remote-endpoint = <&hdmi_in_con>;
507			};
508		};
509
510		port@a {
511			reg = <10>;
512
513			adv7482_txa: endpoint {
514				clock-lanes = <0>;
515				data-lanes = <1 2 3 4>;
516				remote-endpoint = <&csi40_in>;
517			};
518		};
519
520		port@b {
521			reg = <11>;
522
523			adv7482_txb: endpoint {
524				clock-lanes = <0>;
525				data-lanes = <1>;
526				remote-endpoint = <&csi20_in>;
527			};
528		};
529	};
530};
531
532&i2c_dvfs {
533	status = "okay";
534
535	clock-frequency = <400000>;
536
537	pmic: pmic@30 {
538		pinctrl-0 = <&irq0_pins>;
539		pinctrl-names = "default";
540
541		compatible = "rohm,bd9571mwv";
542		reg = <0x30>;
543		interrupt-parent = <&intc_ex>;
544		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
545		interrupt-controller;
546		#interrupt-cells = <2>;
547		gpio-controller;
548		#gpio-cells = <2>;
549		rohm,ddr-backup-power = <0xf>;
550		rohm,rstbmode-level;
551
552		regulators {
553			dvfs: dvfs {
554				regulator-name = "dvfs";
555				regulator-min-microvolt = <750000>;
556				regulator-max-microvolt = <1030000>;
557				regulator-boot-on;
558				regulator-always-on;
559			};
560		};
561	};
562
563	eeprom@50 {
564		compatible = "rohm,br24t01", "atmel,24c01";
565		reg = <0x50>;
566		pagesize = <8>;
567	};
568};
569
570&ohci0 {
571	dr_mode = "otg";
572	status = "okay";
573};
574
575&ohci1 {
576	status = "okay";
577};
578
579&pcie_bus_clk {
580	clock-frequency = <100000000>;
581};
582
583&pciec0 {
584	status = "okay";
585};
586
587&pciec1 {
588	status = "okay";
589};
590
591&pfc {
592	pinctrl-0 = <&scif_clk_pins>;
593	pinctrl-names = "default";
594
595	avb_pins: avb {
596		mux {
597			groups = "avb_link", "avb_mdio", "avb_mii";
598			function = "avb";
599		};
600
601		pins_mdio {
602			groups = "avb_mdio";
603			drive-strength = <24>;
604		};
605
606		pins_mii_tx {
607			pins = "PIN_AVB_TX_CTL", "PIN_AVB_TXC", "PIN_AVB_TD0",
608			       "PIN_AVB_TD1", "PIN_AVB_TD2", "PIN_AVB_TD3";
609			drive-strength = <12>;
610		};
611	};
612
613	du_pins: du {
614		groups = "du_rgb888", "du_sync", "du_oddf", "du_clk_out_0";
615		function = "du";
616	};
617
618	hscif1_pins: hscif1 {
619		groups = "hscif1_data_a", "hscif1_ctrl_a";
620		function = "hscif1";
621	};
622
623	i2c2_pins: i2c2 {
624		groups = "i2c2_a";
625		function = "i2c2";
626	};
627
628	irq0_pins: irq0 {
629		groups = "intc_ex_irq0";
630		function = "intc_ex";
631	};
632
633	keys_pins: keys {
634		pins = "GP_5_17", "GP_5_20", "GP_5_22";
635		bias-pull-up;
636	};
637
638	pwm1_pins: pwm1 {
639		groups = "pwm1_a";
640		function = "pwm1";
641	};
642
643	scif1_pins: scif1 {
644		groups = "scif1_data_a", "scif1_ctrl";
645		function = "scif1";
646	};
647
648	scif2_pins: scif2 {
649		groups = "scif2_data_a";
650		function = "scif2";
651	};
652
653	scif_clk_pins: scif_clk {
654		groups = "scif_clk_a";
655		function = "scif_clk";
656	};
657
658	sdhi0_pins: sd0 {
659		groups = "sdhi0_data4", "sdhi0_ctrl";
660		function = "sdhi0";
661		power-source = <3300>;
662	};
663
664	sdhi0_pins_uhs: sd0_uhs {
665		groups = "sdhi0_data4", "sdhi0_ctrl";
666		function = "sdhi0";
667		power-source = <1800>;
668	};
669
670	sdhi2_pins: sd2 {
671		groups = "sdhi2_data8", "sdhi2_ctrl", "sdhi2_ds";
672		function = "sdhi2";
673		power-source = <1800>;
674	};
675
676	sdhi3_pins: sd3 {
677		groups = "sdhi3_data4", "sdhi3_ctrl";
678		function = "sdhi3";
679		power-source = <3300>;
680	};
681
682	sdhi3_pins_uhs: sd3_uhs {
683		groups = "sdhi3_data4", "sdhi3_ctrl";
684		function = "sdhi3";
685		power-source = <1800>;
686	};
687
688	sound_pins: sound {
689		groups = "ssi01239_ctrl", "ssi0_data", "ssi1_data_a";
690		function = "ssi";
691	};
692
693	sound_clk_pins: sound_clk {
694		groups = "audio_clk_a_a", "audio_clk_b_a", "audio_clk_c_a",
695			 "audio_clkout_a", "audio_clkout3_a";
696		function = "audio_clk";
697	};
698
699	usb0_pins: usb0 {
700		groups = "usb0";
701		function = "usb0";
702	};
703
704	usb1_pins: usb1 {
705		mux {
706			groups = "usb1";
707			function = "usb1";
708		};
709
710		ovc {
711			pins = "GP_6_27";
712			bias-pull-up;
713		};
714
715		pwen {
716			pins = "GP_6_26";
717			bias-pull-down;
718		};
719	};
720
721	usb30_pins: usb30 {
722		groups = "usb30";
723		function = "usb30";
724	};
725};
726
727&pwm1 {
728	pinctrl-0 = <&pwm1_pins>;
729	pinctrl-names = "default";
730
731	status = "okay";
732};
733
734&rcar_sound {
735	pinctrl-0 = <&sound_pins &sound_clk_pins>;
736	pinctrl-names = "default";
737
738	/* Single DAI */
739	#sound-dai-cells = <0>;
740
741	/* audio_clkout0/1/2/3 */
742	#clock-cells = <1>;
743	clock-frequency = <12288000 11289600>;
744
745	status = "okay";
746
747	/* update <audio_clk_b> to <cs2000> */
748	clocks = <&cpg CPG_MOD 1005>,
749		 <&cpg CPG_MOD 1006>, <&cpg CPG_MOD 1007>,
750		 <&cpg CPG_MOD 1008>, <&cpg CPG_MOD 1009>,
751		 <&cpg CPG_MOD 1010>, <&cpg CPG_MOD 1011>,
752		 <&cpg CPG_MOD 1012>, <&cpg CPG_MOD 1013>,
753		 <&cpg CPG_MOD 1014>, <&cpg CPG_MOD 1015>,
754		 <&cpg CPG_MOD 1022>, <&cpg CPG_MOD 1023>,
755		 <&cpg CPG_MOD 1024>, <&cpg CPG_MOD 1025>,
756		 <&cpg CPG_MOD 1026>, <&cpg CPG_MOD 1027>,
757		 <&cpg CPG_MOD 1028>, <&cpg CPG_MOD 1029>,
758		 <&cpg CPG_MOD 1030>, <&cpg CPG_MOD 1031>,
759		 <&cpg CPG_MOD 1020>, <&cpg CPG_MOD 1021>,
760		 <&cpg CPG_MOD 1020>, <&cpg CPG_MOD 1021>,
761		 <&cpg CPG_MOD 1019>, <&cpg CPG_MOD 1018>,
762		 <&audio_clk_a>, <&cs2000>,
763		 <&audio_clk_c>,
764		 <&cpg CPG_CORE CPG_AUDIO_CLK_I>;
765
766	ports {
767		#address-cells = <1>;
768		#size-cells = <0>;
769		rsnd_port0: port@0 {
770			reg = <0>;
771			rsnd_endpoint0: endpoint {
772				remote-endpoint = <&ak4613_endpoint>;
773
774				dai-format = "left_j";
775				bitclock-master = <&rsnd_endpoint0>;
776				frame-master = <&rsnd_endpoint0>;
777
778				playback = <&ssi0 &src0 &dvc0>;
779				capture  = <&ssi1 &src1 &dvc1>;
780			};
781		};
782	};
783};
784
785&rwdt {
786	timeout-sec = <60>;
787	status = "okay";
788};
789
790&scif1 {
791	pinctrl-0 = <&scif1_pins>;
792	pinctrl-names = "default";
793
794	uart-has-rtscts;
795	/* Please only enable hscif1 or scif1 */
796	/* status = "okay"; */
797};
798
799&scif2 {
800	pinctrl-0 = <&scif2_pins>;
801	pinctrl-names = "default";
802
803	status = "okay";
804};
805
806&scif_clk {
807	clock-frequency = <14745600>;
808};
809
810&sdhi0 {
811	pinctrl-0 = <&sdhi0_pins>;
812	pinctrl-1 = <&sdhi0_pins_uhs>;
813	pinctrl-names = "default", "state_uhs";
814
815	vmmc-supply = <&vcc_sdhi0>;
816	vqmmc-supply = <&vccq_sdhi0>;
817	cd-gpios = <&gpio3 12 GPIO_ACTIVE_LOW>;
818	wp-gpios = <&gpio3 13 GPIO_ACTIVE_HIGH>;
819	bus-width = <4>;
820	sd-uhs-sdr50;
821	sd-uhs-sdr104;
822	status = "okay";
823};
824
825&sdhi2 {
826	/* used for on-board 8bit eMMC */
827	pinctrl-0 = <&sdhi2_pins>;
828	pinctrl-1 = <&sdhi2_pins>;
829	pinctrl-names = "default", "state_uhs";
830
831	vmmc-supply = <&reg_3p3v>;
832	vqmmc-supply = <&reg_1p8v>;
833	bus-width = <8>;
834	mmc-hs200-1_8v;
835	mmc-hs400-1_8v;
836	non-removable;
837	fixed-emmc-driver-type = <1>;
838	status = "okay";
839};
840
841&sdhi3 {
842	pinctrl-0 = <&sdhi3_pins>;
843	pinctrl-1 = <&sdhi3_pins_uhs>;
844	pinctrl-names = "default", "state_uhs";
845
846	vmmc-supply = <&vcc_sdhi3>;
847	vqmmc-supply = <&vccq_sdhi3>;
848	cd-gpios = <&gpio4 15 GPIO_ACTIVE_LOW>;
849	wp-gpios = <&gpio4 16 GPIO_ACTIVE_HIGH>;
850	bus-width = <4>;
851	sd-uhs-sdr50;
852	sd-uhs-sdr104;
853	status = "okay";
854};
855
856&ssi1 {
857	shared-pin;
858};
859
860&usb_extal_clk {
861	clock-frequency = <50000000>;
862};
863
864&usb2_phy0 {
865	pinctrl-0 = <&usb0_pins>;
866	pinctrl-names = "default";
867
868	vbus-supply = <&vbus0_usb2>;
869	status = "okay";
870};
871
872&usb2_phy1 {
873	pinctrl-0 = <&usb1_pins>;
874	pinctrl-names = "default";
875
876	status = "okay";
877};
878
879&usb3_peri0 {
880	phys = <&usb3_phy0>;
881	phy-names = "usb";
882
883	companion = <&xhci0>;
884
885	status = "okay";
886};
887
888&usb3_phy0 {
889	status = "okay";
890};
891
892&usb3s0_clk {
893	clock-frequency = <100000000>;
894};
895
896&vin0 {
897	status = "okay";
898};
899
900&vin1 {
901	status = "okay";
902};
903
904&vin2 {
905	status = "okay";
906};
907
908&vin3 {
909	status = "okay";
910};
911
912&vin4 {
913	status = "okay";
914};
915
916&vin5 {
917	status = "okay";
918};
919
920&vin6 {
921	status = "okay";
922};
923
924&vin7 {
925	status = "okay";
926};
927
928&xhci0 {
929	pinctrl-0 = <&usb30_pins>;
930	pinctrl-names = "default";
931
932	status = "okay";
933};
934