xref: /openbmc/linux/arch/arm64/boot/dts/qcom/sm8250.dtsi (revision d455f204)

// SPDX-License-Identifier: BSD-3-Clause
/*
 * Copyright (c) 2020, The Linux Foundation. All rights reserved.
 */

#include <dt-bindings/interrupt-controller/arm-gic.h>
#include <dt-bindings/clock/qcom,dispcc-sm8250.h>
#include <dt-bindings/clock/qcom,gcc-sm8250.h>
#include <dt-bindings/clock/qcom,gpucc-sm8250.h>
#include <dt-bindings/clock/qcom,rpmh.h>
#include <dt-bindings/clock/qcom,sm8250-lpass-aoncc.h>
#include <dt-bindings/clock/qcom,sm8250-lpass-audiocc.h>
#include <dt-bindings/dma/qcom-gpi.h>
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/interconnect/qcom,osm-l3.h>
#include <dt-bindings/interconnect/qcom,sm8250.h>
#include <dt-bindings/mailbox/qcom-ipcc.h>
#include <dt-bindings/power/qcom-rpmpd.h>
#include <dt-bindings/soc/qcom,apr.h>
#include <dt-bindings/soc/qcom,rpmh-rsc.h>
#include <dt-bindings/sound/qcom,q6afe.h>
#include <dt-bindings/thermal/thermal.h>
#include <dt-bindings/clock/qcom,camcc-sm8250.h>
#include <dt-bindings/clock/qcom,videocc-sm8250.h>

/ {
	interrupt-parent = <&intc>;

	#address-cells = <2>;
	#size-cells = <2>;

	aliases {
		i2c0 = &i2c0;
		i2c1 = &i2c1;
		i2c2 = &i2c2;
		i2c3 = &i2c3;
		i2c4 = &i2c4;
		i2c5 = &i2c5;
		i2c6 = &i2c6;
		i2c7 = &i2c7;
		i2c8 = &i2c8;
		i2c9 = &i2c9;
		i2c10 = &i2c10;
		i2c11 = &i2c11;
		i2c12 = &i2c12;
		i2c13 = &i2c13;
		i2c14 = &i2c14;
		i2c15 = &i2c15;
		i2c16 = &i2c16;
		i2c17 = &i2c17;
		i2c18 = &i2c18;
		i2c19 = &i2c19;
		spi0 = &spi0;
		spi1 = &spi1;
		spi2 = &spi2;
		spi3 = &spi3;
		spi4 = &spi4;
		spi5 = &spi5;
		spi6 = &spi6;
		spi7 = &spi7;
		spi8 = &spi8;
		spi9 = &spi9;
		spi10 = &spi10;
		spi11 = &spi11;
		spi12 = &spi12;
		spi13 = &spi13;
		spi14 = &spi14;
		spi15 = &spi15;
		spi16 = &spi16;
		spi17 = &spi17;
		spi18 = &spi18;
		spi19 = &spi19;
	};

	chosen { };

	clocks {
		xo_board: xo-board {
			compatible = "fixed-clock";
			#clock-cells = <0>;
			clock-frequency = <38400000>;
			clock-output-names = "xo_board";
		};

		sleep_clk: sleep-clk {
			compatible = "fixed-clock";
			clock-frequency = <32768>;
			#clock-cells = <0>;
		};
	};

	cpus {
		#address-cells = <2>;
		#size-cells = <0>;

		CPU0: cpu@0 {
			device_type = "cpu";
			compatible = "qcom,kryo485";
			reg = <0x0 0x0>;
			enable-method = "psci";
			capacity-dmips-mhz = <448>;
			dynamic-power-coefficient = <205>;
			next-level-cache = <&L2_0>;
			power-domains = <&CPU_PD0>;
			power-domain-names = "psci";
			qcom,freq-domain = <&cpufreq_hw 0>;
			operating-points-v2 = <&cpu0_opp_table>;
			interconnects = <&gem_noc MASTER_AMPSS_M0 &mc_virt SLAVE_EBI_CH0>,
					<&epss_l3 MASTER_OSM_L3_APPS &epss_l3 SLAVE_OSM_L3>;
			#cooling-cells = <2>;
			L2_0: l2-cache {
				compatible = "cache";
				next-level-cache = <&L3_0>;
				L3_0: l3-cache {
					compatible = "cache";
				};
			};
		};

		CPU1: cpu@100 {
			device_type = "cpu";
			compatible = "qcom,kryo485";
			reg = <0x0 0x100>;
			enable-method = "psci";
			capacity-dmips-mhz = <448>;
			dynamic-power-coefficient = <205>;
			next-level-cache = <&L2_100>;
			power-domains = <&CPU_PD1>;
			power-domain-names = "psci";
			qcom,freq-domain = <&cpufreq_hw 0>;
			operating-points-v2 = <&cpu0_opp_table>;
			interconnects = <&gem_noc MASTER_AMPSS_M0 &mc_virt SLAVE_EBI_CH0>,
					<&epss_l3 MASTER_OSM_L3_APPS &epss_l3 SLAVE_OSM_L3>;
			#cooling-cells = <2>;
			L2_100: l2-cache {
				compatible = "cache";
				next-level-cache = <&L3_0>;
			};
		};

		CPU2: cpu@200 {
			device_type = "cpu";
			compatible = "qcom,kryo485";
			reg = <0x0 0x200>;
			enable-method = "psci";
			capacity-dmips-mhz = <448>;
			dynamic-power-coefficient = <205>;
			next-level-cache = <&L2_200>;
			power-domains = <&CPU_PD2>;
			power-domain-names = "psci";
			qcom,freq-domain = <&cpufreq_hw 0>;
			operating-points-v2 = <&cpu0_opp_table>;
			interconnects = <&gem_noc MASTER_AMPSS_M0 &mc_virt SLAVE_EBI_CH0>,
					<&epss_l3 MASTER_OSM_L3_APPS &epss_l3 SLAVE_OSM_L3>;
			#cooling-cells = <2>;
			L2_200: l2-cache {
				compatible = "cache";
				next-level-cache = <&L3_0>;
			};
		};

		CPU3: cpu@300 {
			device_type = "cpu";
			compatible = "qcom,kryo485";
			reg = <0x0 0x300>;
			enable-method = "psci";
			capacity-dmips-mhz = <448>;
			dynamic-power-coefficient = <205>;
			next-level-cache = <&L2_300>;
			power-domains = <&CPU_PD3>;
			power-domain-names = "psci";
			qcom,freq-domain = <&cpufreq_hw 0>;
			operating-points-v2 = <&cpu0_opp_table>;
			interconnects = <&gem_noc MASTER_AMPSS_M0 &mc_virt SLAVE_EBI_CH0>,
					<&epss_l3 MASTER_OSM_L3_APPS &epss_l3 SLAVE_OSM_L3>;
			#cooling-cells = <2>;
			L2_300: l2-cache {
				compatible = "cache";
				next-level-cache = <&L3_0>;
			};
		};

		CPU4: cpu@400 {
			device_type = "cpu";
			compatible = "qcom,kryo485";
			reg = <0x0 0x400>;
			enable-method = "psci";
			capacity-dmips-mhz = <1024>;
			dynamic-power-coefficient = <379>;
			next-level-cache = <&L2_400>;
			power-domains = <&CPU_PD4>;
			power-domain-names = "psci";
			qcom,freq-domain = <&cpufreq_hw 1>;
			operating-points-v2 = <&cpu4_opp_table>;
			interconnects = <&gem_noc MASTER_AMPSS_M0 &mc_virt SLAVE_EBI_CH0>,
					<&epss_l3 MASTER_OSM_L3_APPS &epss_l3 SLAVE_OSM_L3>;
			#cooling-cells = <2>;
			L2_400: l2-cache {
				compatible = "cache";
				next-level-cache = <&L3_0>;
			};
		};

		CPU5: cpu@500 {
			device_type = "cpu";
			compatible = "qcom,kryo485";
			reg = <0x0 0x500>;
			enable-method = "psci";
			capacity-dmips-mhz = <1024>;
			dynamic-power-coefficient = <379>;
			next-level-cache = <&L2_500>;
			power-domains = <&CPU_PD5>;
			power-domain-names = "psci";
			qcom,freq-domain = <&cpufreq_hw 1>;
			operating-points-v2 = <&cpu4_opp_table>;
			interconnects = <&gem_noc MASTER_AMPSS_M0 &mc_virt SLAVE_EBI_CH0>,
					<&epss_l3 MASTER_OSM_L3_APPS &epss_l3 SLAVE_OSM_L3>;
			#cooling-cells = <2>;
			L2_500: l2-cache {
				compatible = "cache";
				next-level-cache = <&L3_0>;
			};

		};

		CPU6: cpu@600 {
			device_type = "cpu";
			compatible = "qcom,kryo485";
			reg = <0x0 0x600>;
			enable-method = "psci";
			capacity-dmips-mhz = <1024>;
			dynamic-power-coefficient = <379>;
			next-level-cache = <&L2_600>;
			power-domains = <&CPU_PD6>;
			power-domain-names = "psci";
			qcom,freq-domain = <&cpufreq_hw 1>;
			operating-points-v2 = <&cpu4_opp_table>;
			interconnects = <&gem_noc MASTER_AMPSS_M0 &mc_virt SLAVE_EBI_CH0>,
					<&epss_l3 MASTER_OSM_L3_APPS &epss_l3 SLAVE_OSM_L3>;
			#cooling-cells = <2>;
			L2_600: l2-cache {
				compatible = "cache";
				next-level-cache = <&L3_0>;
			};
		};

		CPU7: cpu@700 {
			device_type = "cpu";
			compatible = "qcom,kryo485";
			reg = <0x0 0x700>;
			enable-method = "psci";
			capacity-dmips-mhz = <1024>;
			dynamic-power-coefficient = <444>;
			next-level-cache = <&L2_700>;
			power-domains = <&CPU_PD7>;
			power-domain-names = "psci";
			qcom,freq-domain = <&cpufreq_hw 2>;
			operating-points-v2 = <&cpu7_opp_table>;
			interconnects = <&gem_noc MASTER_AMPSS_M0 &mc_virt SLAVE_EBI_CH0>,
					<&epss_l3 MASTER_OSM_L3_APPS &epss_l3 SLAVE_OSM_L3>;
			#cooling-cells = <2>;
			L2_700: l2-cache {
				compatible = "cache";
				next-level-cache = <&L3_0>;
			};
		};

		cpu-map {
			cluster0 {
				core0 {
					cpu = <&CPU0>;
				};

				core1 {
					cpu = <&CPU1>;
				};

				core2 {
					cpu = <&CPU2>;
				};

				core3 {
					cpu = <&CPU3>;
				};

				core4 {
					cpu = <&CPU4>;
				};

				core5 {
					cpu = <&CPU5>;
				};

				core6 {
					cpu = <&CPU6>;
				};

				core7 {
					cpu = <&CPU7>;
				};
			};
		};

		idle-states {
			entry-method = "psci";

			LITTLE_CPU_SLEEP_0: cpu-sleep-0-0 {
				compatible = "arm,idle-state";
				idle-state-name = "silver-rail-power-collapse";
				arm,psci-suspend-param = <0x40000004>;
				entry-latency-us = <360>;
				exit-latency-us = <531>;
				min-residency-us = <3934>;
				local-timer-stop;
			};

			BIG_CPU_SLEEP_0: cpu-sleep-1-0 {
				compatible = "arm,idle-state";
				idle-state-name = "gold-rail-power-collapse";
				arm,psci-suspend-param = <0x40000004>;
				entry-latency-us = <702>;
				exit-latency-us = <1061>;
				min-residency-us = <4488>;
				local-timer-stop;
			};
		};

		domain-idle-states {
			CLUSTER_SLEEP_0: cluster-sleep-0 {
				compatible = "domain-idle-state";
				idle-state-name = "cluster-llcc-off";
				arm,psci-suspend-param = <0x4100c244>;
				entry-latency-us = <3264>;
				exit-latency-us = <6562>;
				min-residency-us = <9987>;
				local-timer-stop;
			};
		};
	};

	cpu0_opp_table: opp-table-cpu0 {
		compatible = "operating-points-v2";
		opp-shared;

		cpu0_opp1: opp-300000000 {
			opp-hz = /bits/ 64 <300000000>;
			opp-peak-kBps = <800000 9600000>;
		};

		cpu0_opp2: opp-403200000 {
			opp-hz = /bits/ 64 <403200000>;
			opp-peak-kBps = <800000 9600000>;
		};

		cpu0_opp3: opp-518400000 {
			opp-hz = /bits/ 64 <518400000>;
			opp-peak-kBps = <800000 16588800>;
		};

		cpu0_opp4: opp-614400000 {
			opp-hz = /bits/ 64 <614400000>;
			opp-peak-kBps = <800000 16588800>;
		};

		cpu0_opp5: opp-691200000 {
			opp-hz = /bits/ 64 <691200000>;
			opp-peak-kBps = <800000 19660800>;
		};

		cpu0_opp6: opp-787200000 {
			opp-hz = /bits/ 64 <787200000>;
			opp-peak-kBps = <1804000 19660800>;
		};

		cpu0_opp7: opp-883200000 {
			opp-hz = /bits/ 64 <883200000>;
			opp-peak-kBps = <1804000 23347200>;
		};

		cpu0_opp8: opp-979200000 {
			opp-hz = /bits/ 64 <979200000>;
			opp-peak-kBps = <1804000 26419200>;
		};

		cpu0_opp9: opp-1075200000 {
			opp-hz = /bits/ 64 <1075200000>;
			opp-peak-kBps = <1804000 29491200>;
		};

		cpu0_opp10: opp-1171200000 {
			opp-hz = /bits/ 64 <1171200000>;
			opp-peak-kBps = <1804000 32563200>;
		};

		cpu0_opp11: opp-1248000000 {
			opp-hz = /bits/ 64 <1248000000>;
			opp-peak-kBps = <1804000 36249600>;
		};

		cpu0_opp12: opp-1344000000 {
			opp-hz = /bits/ 64 <1344000000>;
			opp-peak-kBps = <2188000 36249600>;
		};

		cpu0_opp13: opp-1420800000 {
			opp-hz = /bits/ 64 <1420800000>;
			opp-peak-kBps = <2188000 39321600>;
		};

		cpu0_opp14: opp-1516800000 {
			opp-hz = /bits/ 64 <1516800000>;
			opp-peak-kBps = <3072000 42393600>;
		};

		cpu0_opp15: opp-1612800000 {
			opp-hz = /bits/ 64 <1612800000>;
			opp-peak-kBps = <3072000 42393600>;
		};

		cpu0_opp16: opp-1708800000 {
			opp-hz = /bits/ 64 <1708800000>;
			opp-peak-kBps = <4068000 42393600>;
		};

		cpu0_opp17: opp-1804800000 {
			opp-hz = /bits/ 64 <1804800000>;
			opp-peak-kBps = <4068000 42393600>;
		};
	};

	cpu4_opp_table: opp-table-cpu4 {
		compatible = "operating-points-v2";
		opp-shared;

		cpu4_opp1: opp-710400000 {
			opp-hz = /bits/ 64 <710400000>;
			opp-peak-kBps = <1804000 19660800>;
		};

		cpu4_opp2: opp-825600000 {
			opp-hz = /bits/ 64 <825600000>;
			opp-peak-kBps = <2188000 23347200>;
		};

		cpu4_opp3: opp-940800000 {
			opp-hz = /bits/ 64 <940800000>;
			opp-peak-kBps = <2188000 26419200>;
		};

		cpu4_opp4: opp-1056000000 {
			opp-hz = /bits/ 64 <1056000000>;
			opp-peak-kBps = <3072000 26419200>;
		};

		cpu4_opp5: opp-1171200000 {
			opp-hz = /bits/ 64 <1171200000>;
			opp-peak-kBps = <3072000 29491200>;
		};

		cpu4_opp6: opp-1286400000 {
			opp-hz = /bits/ 64 <1286400000>;
			opp-peak-kBps = <4068000 29491200>;
		};

		cpu4_opp7: opp-1382400000 {
			opp-hz = /bits/ 64 <1382400000>;
			opp-peak-kBps = <4068000 32563200>;
		};

		cpu4_opp8: opp-1478400000 {
			opp-hz = /bits/ 64 <1478400000>;
			opp-peak-kBps = <4068000 32563200>;
		};

		cpu4_opp9: opp-1574400000 {
			opp-hz = /bits/ 64 <1574400000>;
			opp-peak-kBps = <5412000 39321600>;
		};

		cpu4_opp10: opp-1670400000 {
			opp-hz = /bits/ 64 <1670400000>;
			opp-peak-kBps = <5412000 42393600>;
		};

		cpu4_opp11: opp-1766400000 {
			opp-hz = /bits/ 64 <1766400000>;
			opp-peak-kBps = <5412000 45465600>;
		};

		cpu4_opp12: opp-1862400000 {
			opp-hz = /bits/ 64 <1862400000>;
			opp-peak-kBps = <6220000 45465600>;
		};

		cpu4_opp13: opp-1958400000 {
			opp-hz = /bits/ 64 <1958400000>;
			opp-peak-kBps = <6220000 48537600>;
		};

		cpu4_opp14: opp-2054400000 {
			opp-hz = /bits/ 64 <2054400000>;
			opp-peak-kBps = <7216000 48537600>;
		};

		cpu4_opp15: opp-2150400000 {
			opp-hz = /bits/ 64 <2150400000>;
			opp-peak-kBps = <7216000 51609600>;
		};

		cpu4_opp16: opp-2246400000 {
			opp-hz = /bits/ 64 <2246400000>;
			opp-peak-kBps = <7216000 51609600>;
		};

		cpu4_opp17: opp-2342400000 {
			opp-hz = /bits/ 64 <2342400000>;
			opp-peak-kBps = <8368000 51609600>;
		};

		cpu4_opp18: opp-2419200000 {
			opp-hz = /bits/ 64 <2419200000>;
			opp-peak-kBps = <8368000 51609600>;
		};
	};

	cpu7_opp_table: opp-table-cpu7 {
		compatible = "operating-points-v2";
		opp-shared;

		cpu7_opp1: opp-844800000 {
			opp-hz = /bits/ 64 <844800000>;
			opp-peak-kBps = <2188000 19660800>;
		};

		cpu7_opp2: opp-960000000 {
			opp-hz = /bits/ 64 <960000000>;
			opp-peak-kBps = <2188000 26419200>;
		};

		cpu7_opp3: opp-1075200000 {
			opp-hz = /bits/ 64 <1075200000>;
			opp-peak-kBps = <3072000 26419200>;
		};

		cpu7_opp4: opp-1190400000 {
			opp-hz = /bits/ 64 <1190400000>;
			opp-peak-kBps = <3072000 29491200>;
		};

		cpu7_opp5: opp-1305600000 {
			opp-hz = /bits/ 64 <1305600000>;
			opp-peak-kBps = <4068000 32563200>;
		};

		cpu7_opp6: opp-1401600000 {
			opp-hz = /bits/ 64 <1401600000>;
			opp-peak-kBps = <4068000 32563200>;
		};

		cpu7_opp7: opp-1516800000 {
			opp-hz = /bits/ 64 <1516800000>;
			opp-peak-kBps = <4068000 36249600>;
		};

		cpu7_opp8: opp-1632000000 {
			opp-hz = /bits/ 64 <1632000000>;
			opp-peak-kBps = <5412000 39321600>;
		};

		cpu7_opp9: opp-1747200000 {
			opp-hz = /bits/ 64 <1708800000>;
			opp-peak-kBps = <5412000 42393600>;
		};

		cpu7_opp10: opp-1862400000 {
			opp-hz = /bits/ 64 <1862400000>;
			opp-peak-kBps = <6220000 45465600>;
		};

		cpu7_opp11: opp-1977600000 {
			opp-hz = /bits/ 64 <1977600000>;
			opp-peak-kBps = <6220000 48537600>;
		};

		cpu7_opp12: opp-2073600000 {
			opp-hz = /bits/ 64 <2073600000>;
			opp-peak-kBps = <7216000 48537600>;
		};

		cpu7_opp13: opp-2169600000 {
			opp-hz = /bits/ 64 <2169600000>;
			opp-peak-kBps = <7216000 51609600>;
		};

		cpu7_opp14: opp-2265600000 {
			opp-hz = /bits/ 64 <2265600000>;
			opp-peak-kBps = <7216000 51609600>;
		};

		cpu7_opp15: opp-2361600000 {
			opp-hz = /bits/ 64 <2361600000>;
			opp-peak-kBps = <8368000 51609600>;
		};

		cpu7_opp16: opp-2457600000 {
			opp-hz = /bits/ 64 <2457600000>;
			opp-peak-kBps = <8368000 51609600>;
		};

		cpu7_opp17: opp-2553600000 {
			opp-hz = /bits/ 64 <2553600000>;
			opp-peak-kBps = <8368000 51609600>;
		};

		cpu7_opp18: opp-2649600000 {
			opp-hz = /bits/ 64 <2649600000>;
			opp-peak-kBps = <8368000 51609600>;
		};

		cpu7_opp19: opp-2745600000 {
			opp-hz = /bits/ 64 <2745600000>;
			opp-peak-kBps = <8368000 51609600>;
		};

		cpu7_opp20: opp-2841600000 {
			opp-hz = /bits/ 64 <2841600000>;
			opp-peak-kBps = <8368000 51609600>;
		};
	};

	firmware {
		scm: scm {
			compatible = "qcom,scm-sm8250", "qcom,scm";
			#reset-cells = <1>;
		};
	};

	memory@80000000 {
		device_type = "memory";
		/* We expect the bootloader to fill in the size */
		reg = <0x0 0x80000000 0x0 0x0>;
	};

	pmu {
		compatible = "arm,armv8-pmuv3";
		interrupts = <GIC_PPI 7 IRQ_TYPE_LEVEL_LOW>;
	};

	psci {
		compatible = "arm,psci-1.0";
		method = "smc";

		CPU_PD0: cpu0 {
			#power-domain-cells = <0>;
			power-domains = <&CLUSTER_PD>;
			domain-idle-states = <&LITTLE_CPU_SLEEP_0>;
		};

		CPU_PD1: cpu1 {
			#power-domain-cells = <0>;
			power-domains = <&CLUSTER_PD>;
			domain-idle-states = <&LITTLE_CPU_SLEEP_0>;
		};

		CPU_PD2: cpu2 {
			#power-domain-cells = <0>;
			power-domains = <&CLUSTER_PD>;
			domain-idle-states = <&LITTLE_CPU_SLEEP_0>;
		};

		CPU_PD3: cpu3 {
			#power-domain-cells = <0>;
			power-domains = <&CLUSTER_PD>;
			domain-idle-states = <&LITTLE_CPU_SLEEP_0>;
		};

		CPU_PD4: cpu4 {
			#power-domain-cells = <0>;
			power-domains = <&CLUSTER_PD>;
			domain-idle-states = <&BIG_CPU_SLEEP_0>;
		};

		CPU_PD5: cpu5 {
			#power-domain-cells = <0>;
			power-domains = <&CLUSTER_PD>;
			domain-idle-states = <&BIG_CPU_SLEEP_0>;
		};

		CPU_PD6: cpu6 {
			#power-domain-cells = <0>;
			power-domains = <&CLUSTER_PD>;
			domain-idle-states = <&BIG_CPU_SLEEP_0>;
		};

		CPU_PD7: cpu7 {
			#power-domain-cells = <0>;
			power-domains = <&CLUSTER_PD>;
			domain-idle-states = <&BIG_CPU_SLEEP_0>;
		};

		CLUSTER_PD: cpu-cluster0 {
			#power-domain-cells = <0>;
			domain-idle-states = <&CLUSTER_SLEEP_0>;
		};
	};

	qup_opp_table: opp-table-qup {
		compatible = "operating-points-v2";

		opp-50000000 {
			opp-hz = /bits/ 64 <50000000>;
			required-opps = <&rpmhpd_opp_min_svs>;
		};

		opp-75000000 {
			opp-hz = /bits/ 64 <75000000>;
			required-opps = <&rpmhpd_opp_low_svs>;
		};

		opp-120000000 {
			opp-hz = /bits/ 64 <120000000>;
			required-opps = <&rpmhpd_opp_svs>;
		};
	};

	reserved-memory {
		#address-cells = <2>;
		#size-cells = <2>;
		ranges;

		hyp_mem: memory@80000000 {
			reg = <0x0 0x80000000 0x0 0x600000>;
			no-map;
		};

		xbl_aop_mem: memory@80700000 {
			reg = <0x0 0x80700000 0x0 0x160000>;
			no-map;
		};

		cmd_db: memory@80860000 {
			compatible = "qcom,cmd-db";
			reg = <0x0 0x80860000 0x0 0x20000>;
			no-map;
		};

		smem_mem: memory@80900000 {
			reg = <0x0 0x80900000 0x0 0x200000>;
			no-map;
		};

		removed_mem: memory@80b00000 {
			reg = <0x0 0x80b00000 0x0 0x5300000>;
			no-map;
		};

		camera_mem: memory@86200000 {
			reg = <0x0 0x86200000 0x0 0x500000>;
			no-map;
		};

		wlan_mem: memory@86700000 {
			reg = <0x0 0x86700000 0x0 0x100000>;
			no-map;
		};

		ipa_fw_mem: memory@86800000 {
			reg = <0x0 0x86800000 0x0 0x10000>;
			no-map;
		};

		ipa_gsi_mem: memory@86810000 {
			reg = <0x0 0x86810000 0x0 0xa000>;
			no-map;
		};

		gpu_mem: memory@8681a000 {
			reg = <0x0 0x8681a000 0x0 0x2000>;
			no-map;
		};

		npu_mem: memory@86900000 {
			reg = <0x0 0x86900000 0x0 0x500000>;
			no-map;
		};

		video_mem: memory@86e00000 {
			reg = <0x0 0x86e00000 0x0 0x500000>;
			no-map;
		};

		cvp_mem: memory@87300000 {
			reg = <0x0 0x87300000 0x0 0x500000>;
			no-map;
		};

		cdsp_mem: memory@87800000 {
			reg = <0x0 0x87800000 0x0 0x1400000>;
			no-map;
		};

		slpi_mem: memory@88c00000 {
			reg = <0x0 0x88c00000 0x0 0x1500000>;
			no-map;
		};

		adsp_mem: memory@8a100000 {
			reg = <0x0 0x8a100000 0x0 0x1d00000>;
			no-map;
		};

		spss_mem: memory@8be00000 {
			reg = <0x0 0x8be00000 0x0 0x100000>;
			no-map;
		};

		cdsp_secure_heap: memory@8bf00000 {
			reg = <0x0 0x8bf00000 0x0 0x4600000>;
			no-map;
		};
	};

	smem {
		compatible = "qcom,smem";
		memory-region = <&smem_mem>;
		hwlocks = <&tcsr_mutex 3>;
	};

	smp2p-adsp {
		compatible = "qcom,smp2p";
		qcom,smem = <443>, <429>;
		interrupts-extended = <&ipcc IPCC_CLIENT_LPASS
					     IPCC_MPROC_SIGNAL_SMP2P
					     IRQ_TYPE_EDGE_RISING>;
		mboxes = <&ipcc IPCC_CLIENT_LPASS
				IPCC_MPROC_SIGNAL_SMP2P>;

		qcom,local-pid = <0>;
		qcom,remote-pid = <2>;

		smp2p_adsp_out: master-kernel {
			qcom,entry-name = "master-kernel";
			#qcom,smem-state-cells = <1>;
		};

		smp2p_adsp_in: slave-kernel {
			qcom,entry-name = "slave-kernel";
			interrupt-controller;
			#interrupt-cells = <2>;
		};
	};

	smp2p-cdsp {
		compatible = "qcom,smp2p";
		qcom,smem = <94>, <432>;
		interrupts-extended = <&ipcc IPCC_CLIENT_CDSP
					     IPCC_MPROC_SIGNAL_SMP2P
					     IRQ_TYPE_EDGE_RISING>;
		mboxes = <&ipcc IPCC_CLIENT_CDSP
				IPCC_MPROC_SIGNAL_SMP2P>;

		qcom,local-pid = <0>;
		qcom,remote-pid = <5>;

		smp2p_cdsp_out: master-kernel {
			qcom,entry-name = "master-kernel";
			#qcom,smem-state-cells = <1>;
		};

		smp2p_cdsp_in: slave-kernel {
			qcom,entry-name = "slave-kernel";
			interrupt-controller;
			#interrupt-cells = <2>;
		};
	};

	smp2p-slpi {
		compatible = "qcom,smp2p";
		qcom,smem = <481>, <430>;
		interrupts-extended = <&ipcc IPCC_CLIENT_SLPI
					     IPCC_MPROC_SIGNAL_SMP2P
					     IRQ_TYPE_EDGE_RISING>;
		mboxes = <&ipcc IPCC_CLIENT_SLPI
				IPCC_MPROC_SIGNAL_SMP2P>;

		qcom,local-pid = <0>;
		qcom,remote-pid = <3>;

		smp2p_slpi_out: master-kernel {
			qcom,entry-name = "master-kernel";
			#qcom,smem-state-cells = <1>;
		};

		smp2p_slpi_in: slave-kernel {
			qcom,entry-name = "slave-kernel";
			interrupt-controller;
			#interrupt-cells = <2>;
		};
	};

	soc: soc@0 {
		#address-cells = <2>;
		#size-cells = <2>;
		ranges = <0 0 0 0 0x10 0>;
		dma-ranges = <0 0 0 0 0x10 0>;
		compatible = "simple-bus";

		gcc: clock-controller@100000 {
			compatible = "qcom,gcc-sm8250";
			reg = <0x0 0x00100000 0x0 0x1f0000>;
			#clock-cells = <1>;
			#reset-cells = <1>;
			#power-domain-cells = <1>;
			clock-names = "bi_tcxo",
				      "bi_tcxo_ao",
				      "sleep_clk";
			clocks = <&rpmhcc RPMH_CXO_CLK>,
				 <&rpmhcc RPMH_CXO_CLK_A>,
				 <&sleep_clk>;
		};

		ipcc: mailbox@408000 {
			compatible = "qcom,sm8250-ipcc", "qcom,ipcc";
			reg = <0 0x00408000 0 0x1000>;
			interrupts = <GIC_SPI 229 IRQ_TYPE_LEVEL_HIGH>;
			interrupt-controller;
			#interrupt-cells = <3>;
			#mbox-cells = <2>;
		};

		rng: rng@793000 {
			compatible = "qcom,prng-ee";
			reg = <0 0x00793000 0 0x1000>;
			clocks = <&gcc GCC_PRNG_AHB_CLK>;
			clock-names = "core";
		};

		gpi_dma2: dma-controller@800000 {
			compatible = "qcom,sm8250-gpi-dma", "qcom,sdm845-gpi-dma";
			reg = <0 0x00800000 0 0x70000>;
			interrupts = <GIC_SPI 588 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 589 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 590 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 591 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 592 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 593 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 594 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 595 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 596 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 597 IRQ_TYPE_LEVEL_HIGH>;
			dma-channels = <10>;
			dma-channel-mask = <0x3f>;
			iommus = <&apps_smmu 0x76 0x0>;
			#dma-cells = <3>;
			status = "disabled";
		};

		qupv3_id_2: geniqup@8c0000 {
			compatible = "qcom,geni-se-qup";
			reg = <0x0 0x008c0000 0x0 0x6000>;
			clock-names = "m-ahb", "s-ahb";
			clocks = <&gcc GCC_QUPV3_WRAP_2_M_AHB_CLK>,
				 <&gcc GCC_QUPV3_WRAP_2_S_AHB_CLK>;
			#address-cells = <2>;
			#size-cells = <2>;
			iommus = <&apps_smmu 0x63 0x0>;
			ranges;
			status = "disabled";

			i2c14: i2c@880000 {
				compatible = "qcom,geni-i2c";
				reg = <0 0x00880000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP2_S0_CLK>;
				pinctrl-names = "default";
				pinctrl-0 = <&qup_i2c14_default>;
				interrupts = <GIC_SPI 373 IRQ_TYPE_LEVEL_HIGH>;
				dmas = <&gpi_dma2 0 0 QCOM_GPI_I2C>,
				       <&gpi_dma2 1 0 QCOM_GPI_I2C>;
				dma-names = "tx", "rx";
				#address-cells = <1>;
				#size-cells = <0>;
				status = "disabled";
			};

			spi14: spi@880000 {
				compatible = "qcom,geni-spi";
				reg = <0 0x00880000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP2_S0_CLK>;
				interrupts = <GIC_SPI 373 IRQ_TYPE_LEVEL_HIGH>;
				dmas = <&gpi_dma2 0 0 QCOM_GPI_SPI>,
				       <&gpi_dma2 1 0 QCOM_GPI_SPI>;
				dma-names = "tx", "rx";
				power-domains = <&rpmhpd SM8250_CX>;
				operating-points-v2 = <&qup_opp_table>;
				#address-cells = <1>;
				#size-cells = <0>;
				status = "disabled";
			};

			i2c15: i2c@884000 {
				compatible = "qcom,geni-i2c";
				reg = <0 0x00884000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP2_S1_CLK>;
				pinctrl-names = "default";
				pinctrl-0 = <&qup_i2c15_default>;
				interrupts = <GIC_SPI 583 IRQ_TYPE_LEVEL_HIGH>;
				dmas = <&gpi_dma2 0 1 QCOM_GPI_I2C>,
				       <&gpi_dma2 1 1 QCOM_GPI_I2C>;
				dma-names = "tx", "rx";
				#address-cells = <1>;
				#size-cells = <0>;
				status = "disabled";
			};

			spi15: spi@884000 {
				compatible = "qcom,geni-spi";
				reg = <0 0x00884000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP2_S1_CLK>;
				interrupts = <GIC_SPI 583 IRQ_TYPE_LEVEL_HIGH>;
				dmas = <&gpi_dma2 0 1 QCOM_GPI_SPI>,
				       <&gpi_dma2 1 1 QCOM_GPI_SPI>;
				dma-names = "tx", "rx";
				power-domains = <&rpmhpd SM8250_CX>;
				operating-points-v2 = <&qup_opp_table>;
				#address-cells = <1>;
				#size-cells = <0>;
				status = "disabled";
			};

			i2c16: i2c@888000 {
				compatible = "qcom,geni-i2c";
				reg = <0 0x00888000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP2_S2_CLK>;
				pinctrl-names = "default";
				pinctrl-0 = <&qup_i2c16_default>;
				interrupts = <GIC_SPI 584 IRQ_TYPE_LEVEL_HIGH>;
				dmas = <&gpi_dma2 0 2 QCOM_GPI_I2C>,
				       <&gpi_dma2 1 2 QCOM_GPI_I2C>;
				dma-names = "tx", "rx";
				#address-cells = <1>;
				#size-cells = <0>;
				status = "disabled";
			};

			spi16: spi@888000 {
				compatible = "qcom,geni-spi";
				reg = <0 0x00888000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP2_S2_CLK>;
				interrupts = <GIC_SPI 584 IRQ_TYPE_LEVEL_HIGH>;
				dmas = <&gpi_dma2 0 2 QCOM_GPI_SPI>,
				       <&gpi_dma2 1 2 QCOM_GPI_SPI>;
				dma-names = "tx", "rx";
				power-domains = <&rpmhpd SM8250_CX>;
				operating-points-v2 = <&qup_opp_table>;
				#address-cells = <1>;
				#size-cells = <0>;
				status = "disabled";
			};

			i2c17: i2c@88c000 {
				compatible = "qcom,geni-i2c";
				reg = <0 0x0088c000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP2_S3_CLK>;
				pinctrl-names = "default";
				pinctrl-0 = <&qup_i2c17_default>;
				interrupts = <GIC_SPI 585 IRQ_TYPE_LEVEL_HIGH>;
				dmas = <&gpi_dma2 0 3 QCOM_GPI_I2C>,
				       <&gpi_dma2 1 3 QCOM_GPI_I2C>;
				dma-names = "tx", "rx";
				#address-cells = <1>;
				#size-cells = <0>;
				status = "disabled";
			};

			spi17: spi@88c000 {
				compatible = "qcom,geni-spi";
				reg = <0 0x0088c000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP2_S3_CLK>;
				interrupts = <GIC_SPI 585 IRQ_TYPE_LEVEL_HIGH>;
				dmas = <&gpi_dma2 0 3 QCOM_GPI_SPI>,
				       <&gpi_dma2 1 3 QCOM_GPI_SPI>;
				dma-names = "tx", "rx";
				power-domains = <&rpmhpd SM8250_CX>;
				operating-points-v2 = <&qup_opp_table>;
				#address-cells = <1>;
				#size-cells = <0>;
				status = "disabled";
			};

			uart17: serial@88c000 {
				compatible = "qcom,geni-uart";
				reg = <0 0x0088c000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP2_S3_CLK>;
				pinctrl-names = "default";
				pinctrl-0 = <&qup_uart17_default>;
				interrupts = <GIC_SPI 585 IRQ_TYPE_LEVEL_HIGH>;
				power-domains = <&rpmhpd SM8250_CX>;
				operating-points-v2 = <&qup_opp_table>;
				status = "disabled";
			};

			i2c18: i2c@890000 {
				compatible = "qcom,geni-i2c";
				reg = <0 0x00890000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP2_S4_CLK>;
				pinctrl-names = "default";
				pinctrl-0 = <&qup_i2c18_default>;
				interrupts = <GIC_SPI 586 IRQ_TYPE_LEVEL_HIGH>;
				dmas = <&gpi_dma2 0 4 QCOM_GPI_I2C>,
				       <&gpi_dma2 1 4 QCOM_GPI_I2C>;
				dma-names = "tx", "rx";
				#address-cells = <1>;
				#size-cells = <0>;
				status = "disabled";
			};

			spi18: spi@890000 {
				compatible = "qcom,geni-spi";
				reg = <0 0x00890000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP2_S4_CLK>;
				interrupts = <GIC_SPI 586 IRQ_TYPE_LEVEL_HIGH>;
				dmas = <&gpi_dma2 0 4 QCOM_GPI_SPI>,
				       <&gpi_dma2 1 4 QCOM_GPI_SPI>;
				dma-names = "tx", "rx";
				power-domains = <&rpmhpd SM8250_CX>;
				operating-points-v2 = <&qup_opp_table>;
				#address-cells = <1>;
				#size-cells = <0>;
				status = "disabled";
			};

			uart18: serial@890000 {
				compatible = "qcom,geni-uart";
				reg = <0 0x00890000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP2_S4_CLK>;
				pinctrl-names = "default";
				pinctrl-0 = <&qup_uart18_default>;
				interrupts = <GIC_SPI 586 IRQ_TYPE_LEVEL_HIGH>;
				power-domains = <&rpmhpd SM8250_CX>;
				operating-points-v2 = <&qup_opp_table>;
				status = "disabled";
			};

			i2c19: i2c@894000 {
				compatible = "qcom,geni-i2c";
				reg = <0 0x00894000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP2_S5_CLK>;
				pinctrl-names = "default";
				pinctrl-0 = <&qup_i2c19_default>;
				interrupts = <GIC_SPI 587 IRQ_TYPE_LEVEL_HIGH>;
				dmas = <&gpi_dma2 0 5 QCOM_GPI_I2C>,
				       <&gpi_dma2 1 5 QCOM_GPI_I2C>;
				dma-names = "tx", "rx";
				#address-cells = <1>;
				#size-cells = <0>;
				status = "disabled";
			};

			spi19: spi@894000 {
				compatible = "qcom,geni-spi";
				reg = <0 0x00894000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP2_S5_CLK>;
				interrupts = <GIC_SPI 587 IRQ_TYPE_LEVEL_HIGH>;
				dmas = <&gpi_dma2 0 5 QCOM_GPI_SPI>,
				       <&gpi_dma2 1 5 QCOM_GPI_SPI>;
				dma-names = "tx", "rx";
				power-domains = <&rpmhpd SM8250_CX>;
				operating-points-v2 = <&qup_opp_table>;
				#address-cells = <1>;
				#size-cells = <0>;
				status = "disabled";
			};
		};

		gpi_dma0: dma-controller@900000 {
			compatible = "qcom,sm8250-gpi-dma", "qcom,sdm845-gpi-dma";
			reg = <0 0x00900000 0 0x70000>;
			interrupts = <GIC_SPI 244 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 245 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 246 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 247 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 248 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 249 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 250 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 251 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 252 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 253 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 254 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 255 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 256 IRQ_TYPE_LEVEL_HIGH>;
			dma-channels = <15>;
			dma-channel-mask = <0x7ff>;
			iommus = <&apps_smmu 0x5b6 0x0>;
			#dma-cells = <3>;
			status = "disabled";
		};

		qupv3_id_0: geniqup@9c0000 {
			compatible = "qcom,geni-se-qup";
			reg = <0x0 0x009c0000 0x0 0x6000>;
			clock-names = "m-ahb", "s-ahb";
			clocks = <&gcc GCC_QUPV3_WRAP_0_M_AHB_CLK>,
				 <&gcc GCC_QUPV3_WRAP_0_S_AHB_CLK>;
			#address-cells = <2>;
			#size-cells = <2>;
			iommus = <&apps_smmu 0x5a3 0x0>;
			ranges;
			status = "disabled";

			i2c0: i2c@980000 {
				compatible = "qcom,geni-i2c";
				reg = <0 0x00980000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP0_S0_CLK>;
				pinctrl-names = "default";
				pinctrl-0 = <&qup_i2c0_default>;
				interrupts = <GIC_SPI 601 IRQ_TYPE_LEVEL_HIGH>;
				dmas = <&gpi_dma0 0 0 QCOM_GPI_I2C>,
				       <&gpi_dma0 1 0 QCOM_GPI_I2C>;
				dma-names = "tx", "rx";
				#address-cells = <1>;
				#size-cells = <0>;
				status = "disabled";
			};

			spi0: spi@980000 {
				compatible = "qcom,geni-spi";
				reg = <0 0x00980000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP0_S0_CLK>;
				interrupts = <GIC_SPI 601 IRQ_TYPE_LEVEL_HIGH>;
				dmas = <&gpi_dma0 0 0 QCOM_GPI_SPI>,
				       <&gpi_dma0 1 0 QCOM_GPI_SPI>;
				dma-names = "tx", "rx";
				power-domains = <&rpmhpd SM8250_CX>;
				operating-points-v2 = <&qup_opp_table>;
				#address-cells = <1>;
				#size-cells = <0>;
				status = "disabled";
			};

			i2c1: i2c@984000 {
				compatible = "qcom,geni-i2c";
				reg = <0 0x00984000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP0_S1_CLK>;
				pinctrl-names = "default";
				pinctrl-0 = <&qup_i2c1_default>;
				interrupts = <GIC_SPI 602 IRQ_TYPE_LEVEL_HIGH>;
				dmas = <&gpi_dma0 0 1 QCOM_GPI_I2C>,
				       <&gpi_dma0 1 1 QCOM_GPI_I2C>;
				dma-names = "tx", "rx";
				#address-cells = <1>;
				#size-cells = <0>;
				status = "disabled";
			};

			spi1: spi@984000 {
				compatible = "qcom,geni-spi";
				reg = <0 0x00984000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP0_S1_CLK>;
				interrupts = <GIC_SPI 602 IRQ_TYPE_LEVEL_HIGH>;
				dmas = <&gpi_dma0 0 1 QCOM_GPI_SPI>,
				       <&gpi_dma0 1 1 QCOM_GPI_SPI>;
				dma-names = "tx", "rx";
				power-domains = <&rpmhpd SM8250_CX>;
				operating-points-v2 = <&qup_opp_table>;
				#address-cells = <1>;
				#size-cells = <0>;
				status = "disabled";
			};

			i2c2: i2c@988000 {
				compatible = "qcom,geni-i2c";
				reg = <0 0x00988000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP0_S2_CLK>;
				pinctrl-names = "default";
				pinctrl-0 = <&qup_i2c2_default>;
				interrupts = <GIC_SPI 603 IRQ_TYPE_LEVEL_HIGH>;
				dmas = <&gpi_dma0 0 2 QCOM_GPI_I2C>,
				       <&gpi_dma0 1 2 QCOM_GPI_I2C>;
				dma-names = "tx", "rx";
				#address-cells = <1>;
				#size-cells = <0>;
				status = "disabled";
			};

			spi2: spi@988000 {
				compatible = "qcom,geni-spi";
				reg = <0 0x00988000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP0_S2_CLK>;
				interrupts = <GIC_SPI 603 IRQ_TYPE_LEVEL_HIGH>;
				dmas = <&gpi_dma0 0 2 QCOM_GPI_SPI>,
				       <&gpi_dma0 1 2 QCOM_GPI_SPI>;
				dma-names = "tx", "rx";
				power-domains = <&rpmhpd SM8250_CX>;
				operating-points-v2 = <&qup_opp_table>;
				#address-cells = <1>;
				#size-cells = <0>;
				status = "disabled";
			};

			uart2: serial@988000 {
				compatible = "qcom,geni-debug-uart";
				reg = <0 0x00988000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP0_S2_CLK>;
				pinctrl-names = "default";
				pinctrl-0 = <&qup_uart2_default>;
				interrupts = <GIC_SPI 603 IRQ_TYPE_LEVEL_HIGH>;
				power-domains = <&rpmhpd SM8250_CX>;
				operating-points-v2 = <&qup_opp_table>;
				status = "disabled";
			};

			i2c3: i2c@98c000 {
				compatible = "qcom,geni-i2c";
				reg = <0 0x0098c000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP0_S3_CLK>;
				pinctrl-names = "default";
				pinctrl-0 = <&qup_i2c3_default>;
				interrupts = <GIC_SPI 604 IRQ_TYPE_LEVEL_HIGH>;
				dmas = <&gpi_dma0 0 3 QCOM_GPI_I2C>,
				       <&gpi_dma0 1 3 QCOM_GPI_I2C>;
				dma-names = "tx", "rx";
				#address-cells = <1>;
				#size-cells = <0>;
				status = "disabled";
			};

			spi3: spi@98c000 {
				compatible = "qcom,geni-spi";
				reg = <0 0x0098c000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP0_S3_CLK>;
				interrupts = <GIC_SPI 604 IRQ_TYPE_LEVEL_HIGH>;
				dmas = <&gpi_dma0 0 3 QCOM_GPI_SPI>,
				       <&gpi_dma0 1 3 QCOM_GPI_SPI>;
				dma-names = "tx", "rx";
				power-domains = <&rpmhpd SM8250_CX>;
				operating-points-v2 = <&qup_opp_table>;
				#address-cells = <1>;
				#size-cells = <0>;
				status = "disabled";
			};

			i2c4: i2c@990000 {
				compatible = "qcom,geni-i2c";
				reg = <0 0x00990000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP0_S4_CLK>;
				pinctrl-names = "default";
				pinctrl-0 = <&qup_i2c4_default>;
				interrupts = <GIC_SPI 605 IRQ_TYPE_LEVEL_HIGH>;
				dmas = <&gpi_dma0 0 4 QCOM_GPI_I2C>,
				       <&gpi_dma0 1 4 QCOM_GPI_I2C>;
				dma-names = "tx", "rx";
				#address-cells = <1>;
				#size-cells = <0>;
				status = "disabled";
			};

			spi4: spi@990000 {
				compatible = "qcom,geni-spi";
				reg = <0 0x00990000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP0_S4_CLK>;
				interrupts = <GIC_SPI 605 IRQ_TYPE_LEVEL_HIGH>;
				dmas = <&gpi_dma0 0 4 QCOM_GPI_SPI>,
				       <&gpi_dma0 1 4 QCOM_GPI_SPI>;
				dma-names = "tx", "rx";
				power-domains = <&rpmhpd SM8250_CX>;
				operating-points-v2 = <&qup_opp_table>;
				#address-cells = <1>;
				#size-cells = <0>;
				status = "disabled";
			};

			i2c5: i2c@994000 {
				compatible = "qcom,geni-i2c";
				reg = <0 0x00994000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP0_S5_CLK>;
				pinctrl-names = "default";
				pinctrl-0 = <&qup_i2c5_default>;
				interrupts = <GIC_SPI 606 IRQ_TYPE_LEVEL_HIGH>;
				dmas = <&gpi_dma0 0 5 QCOM_GPI_I2C>,
				       <&gpi_dma0 1 5 QCOM_GPI_I2C>;
				dma-names = "tx", "rx";
				#address-cells = <1>;
				#size-cells = <0>;
				status = "disabled";
			};

			spi5: spi@994000 {
				compatible = "qcom,geni-spi";
				reg = <0 0x00994000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP0_S5_CLK>;
				interrupts = <GIC_SPI 606 IRQ_TYPE_LEVEL_HIGH>;
				dmas = <&gpi_dma0 0 5 QCOM_GPI_SPI>,
				       <&gpi_dma0 1 5 QCOM_GPI_SPI>;
				dma-names = "tx", "rx";
				power-domains = <&rpmhpd SM8250_CX>;
				operating-points-v2 = <&qup_opp_table>;
				#address-cells = <1>;
				#size-cells = <0>;
				status = "disabled";
			};

			i2c6: i2c@998000 {
				compatible = "qcom,geni-i2c";
				reg = <0 0x00998000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP0_S6_CLK>;
				pinctrl-names = "default";
				pinctrl-0 = <&qup_i2c6_default>;
				interrupts = <GIC_SPI 607 IRQ_TYPE_LEVEL_HIGH>;
				dmas = <&gpi_dma0 0 6 QCOM_GPI_I2C>,
				       <&gpi_dma0 1 6 QCOM_GPI_I2C>;
				dma-names = "tx", "rx";
				#address-cells = <1>;
				#size-cells = <0>;
				status = "disabled";
			};

			spi6: spi@998000 {
				compatible = "qcom,geni-spi";
				reg = <0 0x00998000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP0_S6_CLK>;
				interrupts = <GIC_SPI 607 IRQ_TYPE_LEVEL_HIGH>;
				dmas = <&gpi_dma0 0 6 QCOM_GPI_SPI>,
				       <&gpi_dma0 1 6 QCOM_GPI_SPI>;
				dma-names = "tx", "rx";
				power-domains = <&rpmhpd SM8250_CX>;
				operating-points-v2 = <&qup_opp_table>;
				#address-cells = <1>;
				#size-cells = <0>;
				status = "disabled";
			};

			uart6: serial@998000 {
				compatible = "qcom,geni-uart";
				reg = <0 0x00998000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP0_S6_CLK>;
				pinctrl-names = "default";
				pinctrl-0 = <&qup_uart6_default>;
				interrupts = <GIC_SPI 607 IRQ_TYPE_LEVEL_HIGH>;
				power-domains = <&rpmhpd SM8250_CX>;
				operating-points-v2 = <&qup_opp_table>;
				status = "disabled";
			};

			i2c7: i2c@99c000 {
				compatible = "qcom,geni-i2c";
				reg = <0 0x0099c000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP0_S7_CLK>;
				pinctrl-names = "default";
				pinctrl-0 = <&qup_i2c7_default>;
				interrupts = <GIC_SPI 608 IRQ_TYPE_LEVEL_HIGH>;
				dmas = <&gpi_dma0 0 7 QCOM_GPI_I2C>,
				       <&gpi_dma0 1 7 QCOM_GPI_I2C>;
				dma-names = "tx", "rx";
				#address-cells = <1>;
				#size-cells = <0>;
				status = "disabled";
			};

			spi7: spi@99c000 {
				compatible = "qcom,geni-spi";
				reg = <0 0x0099c000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP0_S7_CLK>;
				interrupts = <GIC_SPI 608 IRQ_TYPE_LEVEL_HIGH>;
				dmas = <&gpi_dma0 0 7 QCOM_GPI_SPI>,
				       <&gpi_dma0 1 7 QCOM_GPI_SPI>;
				dma-names = "tx", "rx";
				power-domains = <&rpmhpd SM8250_CX>;
				operating-points-v2 = <&qup_opp_table>;
				#address-cells = <1>;
				#size-cells = <0>;
				status = "disabled";
			};
		};

		gpi_dma1: dma-controller@a00000 {
			compatible = "qcom,sm8250-gpi-dma", "qcom,sdm845-gpi-dma";
			reg = <0 0x00a00000 0 0x70000>;
			interrupts = <GIC_SPI 279 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 280 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 281 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 282 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 283 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 284 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 293 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 294 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 295 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 296 IRQ_TYPE_LEVEL_HIGH>;
			dma-channels = <10>;
			dma-channel-mask = <0x3f>;
			iommus = <&apps_smmu 0x56 0x0>;
			#dma-cells = <3>;
			status = "disabled";
		};

		qupv3_id_1: geniqup@ac0000 {
			compatible = "qcom,geni-se-qup";
			reg = <0x0 0x00ac0000 0x0 0x6000>;
			clock-names = "m-ahb", "s-ahb";
			clocks = <&gcc GCC_QUPV3_WRAP_1_M_AHB_CLK>,
				 <&gcc GCC_QUPV3_WRAP_1_S_AHB_CLK>;
			#address-cells = <2>;
			#size-cells = <2>;
			iommus = <&apps_smmu 0x43 0x0>;
			ranges;
			status = "disabled";

			i2c8: i2c@a80000 {
				compatible = "qcom,geni-i2c";
				reg = <0 0x00a80000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP1_S0_CLK>;
				pinctrl-names = "default";
				pinctrl-0 = <&qup_i2c8_default>;
				interrupts = <GIC_SPI 353 IRQ_TYPE_LEVEL_HIGH>;
				dmas = <&gpi_dma1 0 0 QCOM_GPI_I2C>,
				       <&gpi_dma1 1 0 QCOM_GPI_I2C>;
				dma-names = "tx", "rx";
				#address-cells = <1>;
				#size-cells = <0>;
				status = "disabled";
			};

			spi8: spi@a80000 {
				compatible = "qcom,geni-spi";
				reg = <0 0x00a80000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP1_S0_CLK>;
				interrupts = <GIC_SPI 353 IRQ_TYPE_LEVEL_HIGH>;
				dmas = <&gpi_dma1 0 0 QCOM_GPI_SPI>,
				       <&gpi_dma1 1 0 QCOM_GPI_SPI>;
				dma-names = "tx", "rx";
				power-domains = <&rpmhpd SM8250_CX>;
				operating-points-v2 = <&qup_opp_table>;
				#address-cells = <1>;
				#size-cells = <0>;
				status = "disabled";
			};

			i2c9: i2c@a84000 {
				compatible = "qcom,geni-i2c";
				reg = <0 0x00a84000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP1_S1_CLK>;
				pinctrl-names = "default";
				pinctrl-0 = <&qup_i2c9_default>;
				interrupts = <GIC_SPI 354 IRQ_TYPE_LEVEL_HIGH>;
				dmas = <&gpi_dma1 0 1 QCOM_GPI_I2C>,
				       <&gpi_dma1 1 1 QCOM_GPI_I2C>;
				dma-names = "tx", "rx";
				#address-cells = <1>;
				#size-cells = <0>;
				status = "disabled";
			};

			spi9: spi@a84000 {
				compatible = "qcom,geni-spi";
				reg = <0 0x00a84000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP1_S1_CLK>;
				interrupts = <GIC_SPI 354 IRQ_TYPE_LEVEL_HIGH>;
				dmas = <&gpi_dma1 0 1 QCOM_GPI_SPI>,
				       <&gpi_dma1 1 1 QCOM_GPI_SPI>;
				dma-names = "tx", "rx";
				power-domains = <&rpmhpd SM8250_CX>;
				operating-points-v2 = <&qup_opp_table>;
				#address-cells = <1>;
				#size-cells = <0>;
				status = "disabled";
			};

			i2c10: i2c@a88000 {
				compatible = "qcom,geni-i2c";
				reg = <0 0x00a88000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP1_S2_CLK>;
				pinctrl-names = "default";
				pinctrl-0 = <&qup_i2c10_default>;
				interrupts = <GIC_SPI 355 IRQ_TYPE_LEVEL_HIGH>;
				dmas = <&gpi_dma1 0 2 QCOM_GPI_I2C>,
				       <&gpi_dma1 1 2 QCOM_GPI_I2C>;
				dma-names = "tx", "rx";
				#address-cells = <1>;
				#size-cells = <0>;
				status = "disabled";
			};

			spi10: spi@a88000 {
				compatible = "qcom,geni-spi";
				reg = <0 0x00a88000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP1_S2_CLK>;
				interrupts = <GIC_SPI 355 IRQ_TYPE_LEVEL_HIGH>;
				dmas = <&gpi_dma1 0 2 QCOM_GPI_SPI>,
				       <&gpi_dma1 1 2 QCOM_GPI_SPI>;
				dma-names = "tx", "rx";
				power-domains = <&rpmhpd SM8250_CX>;
				operating-points-v2 = <&qup_opp_table>;
				#address-cells = <1>;
				#size-cells = <0>;
				status = "disabled";
			};

			i2c11: i2c@a8c000 {
				compatible = "qcom,geni-i2c";
				reg = <0 0x00a8c000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP1_S3_CLK>;
				pinctrl-names = "default";
				pinctrl-0 = <&qup_i2c11_default>;
				interrupts = <GIC_SPI 356 IRQ_TYPE_LEVEL_HIGH>;
				dmas = <&gpi_dma1 0 3 QCOM_GPI_I2C>,
				       <&gpi_dma1 1 3 QCOM_GPI_I2C>;
				dma-names = "tx", "rx";
				#address-cells = <1>;
				#size-cells = <0>;
				status = "disabled";
			};

			spi11: spi@a8c000 {
				compatible = "qcom,geni-spi";
				reg = <0 0x00a8c000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP1_S3_CLK>;
				interrupts = <GIC_SPI 356 IRQ_TYPE_LEVEL_HIGH>;
				dmas = <&gpi_dma1 0 3 QCOM_GPI_SPI>,
				       <&gpi_dma1 1 3 QCOM_GPI_SPI>;
				dma-names = "tx", "rx";
				power-domains = <&rpmhpd SM8250_CX>;
				operating-points-v2 = <&qup_opp_table>;
				#address-cells = <1>;
				#size-cells = <0>;
				status = "disabled";
			};

			i2c12: i2c@a90000 {
				compatible = "qcom,geni-i2c";
				reg = <0 0x00a90000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP1_S4_CLK>;
				pinctrl-names = "default";
				pinctrl-0 = <&qup_i2c12_default>;
				interrupts = <GIC_SPI 357 IRQ_TYPE_LEVEL_HIGH>;
				dmas = <&gpi_dma1 0 4 QCOM_GPI_I2C>,
				       <&gpi_dma1 1 4 QCOM_GPI_I2C>;
				dma-names = "tx", "rx";
				#address-cells = <1>;
				#size-cells = <0>;
				status = "disabled";
			};

			spi12: spi@a90000 {
				compatible = "qcom,geni-spi";
				reg = <0 0x00a90000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP1_S4_CLK>;
				interrupts = <GIC_SPI 357 IRQ_TYPE_LEVEL_HIGH>;
				dmas = <&gpi_dma1 0 4 QCOM_GPI_SPI>,
				       <&gpi_dma1 1 4 QCOM_GPI_SPI>;
				dma-names = "tx", "rx";
				power-domains = <&rpmhpd SM8250_CX>;
				operating-points-v2 = <&qup_opp_table>;
				#address-cells = <1>;
				#size-cells = <0>;
				status = "disabled";
			};

			uart12: serial@a90000 {
				compatible = "qcom,geni-debug-uart";
				reg = <0x0 0x00a90000 0x0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP1_S4_CLK>;
				pinctrl-names = "default";
				pinctrl-0 = <&qup_uart12_default>;
				interrupts = <GIC_SPI 357 IRQ_TYPE_LEVEL_HIGH>;
				power-domains = <&rpmhpd SM8250_CX>;
				operating-points-v2 = <&qup_opp_table>;
				status = "disabled";
			};

			i2c13: i2c@a94000 {
				compatible = "qcom,geni-i2c";
				reg = <0 0x00a94000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP1_S5_CLK>;
				pinctrl-names = "default";
				pinctrl-0 = <&qup_i2c13_default>;
				interrupts = <GIC_SPI 358 IRQ_TYPE_LEVEL_HIGH>;
				dmas = <&gpi_dma1 0 5 QCOM_GPI_I2C>,
				       <&gpi_dma1 1 5 QCOM_GPI_I2C>;
				dma-names = "tx", "rx";
				#address-cells = <1>;
				#size-cells = <0>;
				status = "disabled";
			};

			spi13: spi@a94000 {
				compatible = "qcom,geni-spi";
				reg = <0 0x00a94000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP1_S5_CLK>;
				interrupts = <GIC_SPI 358 IRQ_TYPE_LEVEL_HIGH>;
				dmas = <&gpi_dma1 0 5 QCOM_GPI_SPI>,
				       <&gpi_dma1 1 5 QCOM_GPI_SPI>;
				dma-names = "tx", "rx";
				power-domains = <&rpmhpd SM8250_CX>;
				operating-points-v2 = <&qup_opp_table>;
				#address-cells = <1>;
				#size-cells = <0>;
				status = "disabled";
			};
		};

		config_noc: interconnect@1500000 {
			compatible = "qcom,sm8250-config-noc";
			reg = <0 0x01500000 0 0xa580>;
			#interconnect-cells = <1>;
			qcom,bcm-voters = <&apps_bcm_voter>;
		};

		system_noc: interconnect@1620000 {
			compatible = "qcom,sm8250-system-noc";
			reg = <0 0x01620000 0 0x1c200>;
			#interconnect-cells = <1>;
			qcom,bcm-voters = <&apps_bcm_voter>;
		};

		mc_virt: interconnect@163d000 {
			compatible = "qcom,sm8250-mc-virt";
			reg = <0 0x0163d000 0 0x1000>;
			#interconnect-cells = <1>;
			qcom,bcm-voters = <&apps_bcm_voter>;
		};

		aggre1_noc: interconnect@16e0000 {
			compatible = "qcom,sm8250-aggre1-noc";
			reg = <0 0x016e0000 0 0x1f180>;
			#interconnect-cells = <1>;
			qcom,bcm-voters = <&apps_bcm_voter>;
		};

		aggre2_noc: interconnect@1700000 {
			compatible = "qcom,sm8250-aggre2-noc";
			reg = <0 0x01700000 0 0x33000>;
			#interconnect-cells = <1>;
			qcom,bcm-voters = <&apps_bcm_voter>;
		};

		compute_noc: interconnect@1733000 {
			compatible = "qcom,sm8250-compute-noc";
			reg = <0 0x01733000 0 0xa180>;
			#interconnect-cells = <1>;
			qcom,bcm-voters = <&apps_bcm_voter>;
		};

		mmss_noc: interconnect@1740000 {
			compatible = "qcom,sm8250-mmss-noc";
			reg = <0 0x01740000 0 0x1f080>;
			#interconnect-cells = <1>;
			qcom,bcm-voters = <&apps_bcm_voter>;
		};

		pcie0: pci@1c00000 {
			compatible = "qcom,pcie-sm8250";
			reg = <0 0x01c00000 0 0x3000>,
			      <0 0x60000000 0 0xf1d>,
			      <0 0x60000f20 0 0xa8>,
			      <0 0x60001000 0 0x1000>,
			      <0 0x60100000 0 0x100000>;
			reg-names = "parf", "dbi", "elbi", "atu", "config";
			device_type = "pci";
			linux,pci-domain = <0>;
			bus-range = <0x00 0xff>;
			num-lanes = <1>;

			#address-cells = <3>;
			#size-cells = <2>;

			ranges = <0x01000000 0x0 0x60200000 0 0x60200000 0x0 0x100000>,
				 <0x02000000 0x0 0x60300000 0 0x60300000 0x0 0x3d00000>;

			interrupts = <GIC_SPI 141 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 142 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 143 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 144 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 145 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 146 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 147 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 148 IRQ_TYPE_LEVEL_HIGH>;
			interrupt-names = "msi0", "msi1", "msi2", "msi3",
					  "msi4", "msi5", "msi6", "msi7";
			#interrupt-cells = <1>;
			interrupt-map-mask = <0 0 0 0x7>;
			interrupt-map = <0 0 0 1 &intc 0 149 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
					<0 0 0 2 &intc 0 150 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
					<0 0 0 3 &intc 0 151 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
					<0 0 0 4 &intc 0 152 IRQ_TYPE_LEVEL_HIGH>; /* int_d */

			clocks = <&gcc GCC_PCIE_0_PIPE_CLK>,
				 <&gcc GCC_PCIE_0_AUX_CLK>,
				 <&gcc GCC_PCIE_0_CFG_AHB_CLK>,
				 <&gcc GCC_PCIE_0_MSTR_AXI_CLK>,
				 <&gcc GCC_PCIE_0_SLV_AXI_CLK>,
				 <&gcc GCC_PCIE_0_SLV_Q2A_AXI_CLK>,
				 <&gcc GCC_AGGRE_NOC_PCIE_TBU_CLK>,
				 <&gcc GCC_DDRSS_PCIE_SF_TBU_CLK>;
			clock-names = "pipe",
				      "aux",
				      "cfg",
				      "bus_master",
				      "bus_slave",
				      "slave_q2a",
				      "tbu",
				      "ddrss_sf_tbu";

			iommus = <&apps_smmu 0x1c00 0x7f>;
			iommu-map = <0x0   &apps_smmu 0x1c00 0x1>,
				    <0x100 &apps_smmu 0x1c01 0x1>;

			resets = <&gcc GCC_PCIE_0_BCR>;
			reset-names = "pci";

			power-domains = <&gcc PCIE_0_GDSC>;

			phys = <&pcie0_lane>;
			phy-names = "pciephy";

			perst-gpios = <&tlmm 79 GPIO_ACTIVE_LOW>;
			wake-gpios = <&tlmm 81 GPIO_ACTIVE_HIGH>;

			pinctrl-names = "default";
			pinctrl-0 = <&pcie0_default_state>;

			status = "disabled";
		};

		pcie0_phy: phy@1c06000 {
			compatible = "qcom,sm8250-qmp-gen3x1-pcie-phy";
			reg = <0 0x01c06000 0 0x1c0>;
			#address-cells = <2>;
			#size-cells = <2>;
			ranges;
			clocks = <&gcc GCC_PCIE_PHY_AUX_CLK>,
				 <&gcc GCC_PCIE_0_CFG_AHB_CLK>,
				 <&gcc GCC_PCIE_WIFI_CLKREF_EN>,
				 <&gcc GCC_PCIE0_PHY_REFGEN_CLK>;
			clock-names = "aux", "cfg_ahb", "ref", "refgen";

			resets = <&gcc GCC_PCIE_0_PHY_BCR>;
			reset-names = "phy";

			assigned-clocks = <&gcc GCC_PCIE0_PHY_REFGEN_CLK>;
			assigned-clock-rates = <100000000>;

			status = "disabled";

			pcie0_lane: phy@1c06200 {
				reg = <0 0x1c06200 0 0x170>, /* tx */
				      <0 0x1c06400 0 0x200>, /* rx */
				      <0 0x1c06800 0 0x1f0>, /* pcs */
				      <0 0x1c06c00 0 0xf4>; /* "pcs_lane" same as pcs_misc? */
				clocks = <&gcc GCC_PCIE_0_PIPE_CLK>;
				clock-names = "pipe0";

				#phy-cells = <0>;

				#clock-cells = <0>;
				clock-output-names = "pcie_0_pipe_clk";
			};
		};

		pcie1: pci@1c08000 {
			compatible = "qcom,pcie-sm8250";
			reg = <0 0x01c08000 0 0x3000>,
			      <0 0x40000000 0 0xf1d>,
			      <0 0x40000f20 0 0xa8>,
			      <0 0x40001000 0 0x1000>,
			      <0 0x40100000 0 0x100000>;
			reg-names = "parf", "dbi", "elbi", "atu", "config";
			device_type = "pci";
			linux,pci-domain = <1>;
			bus-range = <0x00 0xff>;
			num-lanes = <2>;

			#address-cells = <3>;
			#size-cells = <2>;

			ranges = <0x01000000 0x0 0x40200000 0x0 0x40200000 0x0 0x100000>,
				 <0x02000000 0x0 0x40300000 0x0 0x40300000 0x0 0x1fd00000>;

			interrupts = <GIC_SPI 307 IRQ_TYPE_LEVEL_HIGH>;
			interrupt-names = "msi";
			#interrupt-cells = <1>;
			interrupt-map-mask = <0 0 0 0x7>;
			interrupt-map = <0 0 0 1 &intc 0 434 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
					<0 0 0 2 &intc 0 435 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
					<0 0 0 3 &intc 0 438 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
					<0 0 0 4 &intc 0 439 IRQ_TYPE_LEVEL_HIGH>; /* int_d */

			clocks = <&gcc GCC_PCIE_1_PIPE_CLK>,
				 <&gcc GCC_PCIE_1_AUX_CLK>,
				 <&gcc GCC_PCIE_1_CFG_AHB_CLK>,
				 <&gcc GCC_PCIE_1_MSTR_AXI_CLK>,
				 <&gcc GCC_PCIE_1_SLV_AXI_CLK>,
				 <&gcc GCC_PCIE_1_SLV_Q2A_AXI_CLK>,
				 <&gcc GCC_PCIE_WIGIG_CLKREF_EN>,
				 <&gcc GCC_AGGRE_NOC_PCIE_TBU_CLK>,
				 <&gcc GCC_DDRSS_PCIE_SF_TBU_CLK>;
			clock-names = "pipe",
				      "aux",
				      "cfg",
				      "bus_master",
				      "bus_slave",
				      "slave_q2a",
				      "ref",
				      "tbu",
				      "ddrss_sf_tbu";

			assigned-clocks = <&gcc GCC_PCIE_1_AUX_CLK>;
			assigned-clock-rates = <19200000>;

			iommus = <&apps_smmu 0x1c80 0x7f>;
			iommu-map = <0x0   &apps_smmu 0x1c80 0x1>,
				    <0x100 &apps_smmu 0x1c81 0x1>;

			resets = <&gcc GCC_PCIE_1_BCR>;
			reset-names = "pci";

			power-domains = <&gcc PCIE_1_GDSC>;

			phys = <&pcie1_lane>;
			phy-names = "pciephy";

			perst-gpios = <&tlmm 82 GPIO_ACTIVE_LOW>;
			wake-gpios = <&tlmm 84 GPIO_ACTIVE_HIGH>;

			pinctrl-names = "default";
			pinctrl-0 = <&pcie1_default_state>;

			status = "disabled";
		};

		pcie1_phy: phy@1c0e000 {
			compatible = "qcom,sm8250-qmp-gen3x2-pcie-phy";
			reg = <0 0x01c0e000 0 0x1c0>;
			#address-cells = <2>;
			#size-cells = <2>;
			ranges;
			clocks = <&gcc GCC_PCIE_PHY_AUX_CLK>,
				 <&gcc GCC_PCIE_1_CFG_AHB_CLK>,
				 <&gcc GCC_PCIE_WIGIG_CLKREF_EN>,
				 <&gcc GCC_PCIE1_PHY_REFGEN_CLK>;
			clock-names = "aux", "cfg_ahb", "ref", "refgen";

			resets = <&gcc GCC_PCIE_1_PHY_BCR>;
			reset-names = "phy";

			assigned-clocks = <&gcc GCC_PCIE1_PHY_REFGEN_CLK>;
			assigned-clock-rates = <100000000>;

			status = "disabled";

			pcie1_lane: phy@1c0e200 {
				reg = <0 0x1c0e200 0 0x170>, /* tx0 */
				      <0 0x1c0e400 0 0x200>, /* rx0 */
				      <0 0x1c0ea00 0 0x1f0>, /* pcs */
				      <0 0x1c0e600 0 0x170>, /* tx1 */
				      <0 0x1c0e800 0 0x200>, /* rx1 */
				      <0 0x1c0ee00 0 0xf4>; /* "pcs_com" same as pcs_misc? */
				clocks = <&gcc GCC_PCIE_1_PIPE_CLK>;
				clock-names = "pipe0";

				#phy-cells = <0>;

				#clock-cells = <0>;
				clock-output-names = "pcie_1_pipe_clk";
			};
		};

		pcie2: pci@1c10000 {
			compatible = "qcom,pcie-sm8250";
			reg = <0 0x01c10000 0 0x3000>,
			      <0 0x64000000 0 0xf1d>,
			      <0 0x64000f20 0 0xa8>,
			      <0 0x64001000 0 0x1000>,
			      <0 0x64100000 0 0x100000>;
			reg-names = "parf", "dbi", "elbi", "atu", "config";
			device_type = "pci";
			linux,pci-domain = <2>;
			bus-range = <0x00 0xff>;
			num-lanes = <2>;

			#address-cells = <3>;
			#size-cells = <2>;

			ranges = <0x01000000 0x0 0x64200000 0x0 0x64200000 0x0 0x100000>,
				 <0x02000000 0x0 0x64300000 0x0 0x64300000 0x0 0x3d00000>;

			interrupts = <GIC_SPI 243 IRQ_TYPE_LEVEL_HIGH>;
			interrupt-names = "msi";
			#interrupt-cells = <1>;
			interrupt-map-mask = <0 0 0 0x7>;
			interrupt-map = <0 0 0 1 &intc 0 290 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
					<0 0 0 2 &intc 0 415 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
					<0 0 0 3 &intc 0 416 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
					<0 0 0 4 &intc 0 417 IRQ_TYPE_LEVEL_HIGH>; /* int_d */

			clocks = <&gcc GCC_PCIE_2_PIPE_CLK>,
				 <&gcc GCC_PCIE_2_AUX_CLK>,
				 <&gcc GCC_PCIE_2_CFG_AHB_CLK>,
				 <&gcc GCC_PCIE_2_MSTR_AXI_CLK>,
				 <&gcc GCC_PCIE_2_SLV_AXI_CLK>,
				 <&gcc GCC_PCIE_2_SLV_Q2A_AXI_CLK>,
				 <&gcc GCC_PCIE_MDM_CLKREF_EN>,
				 <&gcc GCC_AGGRE_NOC_PCIE_TBU_CLK>,
				 <&gcc GCC_DDRSS_PCIE_SF_TBU_CLK>;
			clock-names = "pipe",
				      "aux",
				      "cfg",
				      "bus_master",
				      "bus_slave",
				      "slave_q2a",
				      "ref",
				      "tbu",
				      "ddrss_sf_tbu";

			assigned-clocks = <&gcc GCC_PCIE_2_AUX_CLK>;
			assigned-clock-rates = <19200000>;

			iommus = <&apps_smmu 0x1d00 0x7f>;
			iommu-map = <0x0   &apps_smmu 0x1d00 0x1>,
				    <0x100 &apps_smmu 0x1d01 0x1>;

			resets = <&gcc GCC_PCIE_2_BCR>;
			reset-names = "pci";

			power-domains = <&gcc PCIE_2_GDSC>;

			phys = <&pcie2_lane>;
			phy-names = "pciephy";

			perst-gpios = <&tlmm 85 GPIO_ACTIVE_LOW>;
			wake-gpios = <&tlmm 87 GPIO_ACTIVE_HIGH>;

			pinctrl-names = "default";
			pinctrl-0 = <&pcie2_default_state>;

			status = "disabled";
		};

		pcie2_phy: phy@1c16000 {
			compatible = "qcom,sm8250-qmp-modem-pcie-phy";
			reg = <0 0x1c16000 0 0x1c0>;
			#address-cells = <2>;
			#size-cells = <2>;
			ranges;
			clocks = <&gcc GCC_PCIE_PHY_AUX_CLK>,
				 <&gcc GCC_PCIE_2_CFG_AHB_CLK>,
				 <&gcc GCC_PCIE_MDM_CLKREF_EN>,
				 <&gcc GCC_PCIE2_PHY_REFGEN_CLK>;
			clock-names = "aux", "cfg_ahb", "ref", "refgen";

			resets = <&gcc GCC_PCIE_2_PHY_BCR>;
			reset-names = "phy";

			assigned-clocks = <&gcc GCC_PCIE2_PHY_REFGEN_CLK>;
			assigned-clock-rates = <100000000>;

			status = "disabled";

			pcie2_lane: phy@1c16200 {
				reg = <0 0x1c16200 0 0x170>, /* tx0 */
				      <0 0x1c16400 0 0x200>, /* rx0 */
				      <0 0x1c16a00 0 0x1f0>, /* pcs */
				      <0 0x1c16600 0 0x170>, /* tx1 */
				      <0 0x1c16800 0 0x200>, /* rx1 */
				      <0 0x1c16e00 0 0xf4>; /* "pcs_com" same as pcs_misc? */
				clocks = <&gcc GCC_PCIE_2_PIPE_CLK>;
				clock-names = "pipe0";

				#phy-cells = <0>;

				#clock-cells = <0>;
				clock-output-names = "pcie_2_pipe_clk";
			};
		};

		ufs_mem_hc: ufshc@1d84000 {
			compatible = "qcom,sm8250-ufshc", "qcom,ufshc",
				     "jedec,ufs-2.0";
			reg = <0 0x01d84000 0 0x3000>;
			interrupts = <GIC_SPI 265 IRQ_TYPE_LEVEL_HIGH>;
			phys = <&ufs_mem_phy_lanes>;
			phy-names = "ufsphy";
			lanes-per-direction = <2>;
			#reset-cells = <1>;
			resets = <&gcc GCC_UFS_PHY_BCR>;
			reset-names = "rst";

			power-domains = <&gcc UFS_PHY_GDSC>;

			iommus = <&apps_smmu 0x0e0 0>, <&apps_smmu 0x4e0 0>;

			clock-names =
				"core_clk",
				"bus_aggr_clk",
				"iface_clk",
				"core_clk_unipro",
				"ref_clk",
				"tx_lane0_sync_clk",
				"rx_lane0_sync_clk",
				"rx_lane1_sync_clk";
			clocks =
				<&gcc GCC_UFS_PHY_AXI_CLK>,
				<&gcc GCC_AGGRE_UFS_PHY_AXI_CLK>,
				<&gcc GCC_UFS_PHY_AHB_CLK>,
				<&gcc GCC_UFS_PHY_UNIPRO_CORE_CLK>,
				<&rpmhcc RPMH_CXO_CLK>,
				<&gcc GCC_UFS_PHY_TX_SYMBOL_0_CLK>,
				<&gcc GCC_UFS_PHY_RX_SYMBOL_0_CLK>,
				<&gcc GCC_UFS_PHY_RX_SYMBOL_1_CLK>;
			freq-table-hz =
				<37500000 300000000>,
				<0 0>,
				<0 0>,
				<37500000 300000000>,
				<0 0>,
				<0 0>,
				<0 0>,
				<0 0>;

			status = "disabled";
		};

		ufs_mem_phy: phy@1d87000 {
			compatible = "qcom,sm8250-qmp-ufs-phy";
			reg = <0 0x01d87000 0 0x1c0>;
			#address-cells = <2>;
			#size-cells = <2>;
			ranges;
			clock-names = "ref",
				      "ref_aux";
			clocks = <&rpmhcc RPMH_CXO_CLK>,
				 <&gcc GCC_UFS_PHY_PHY_AUX_CLK>;

			resets = <&ufs_mem_hc 0>;
			reset-names = "ufsphy";
			status = "disabled";

			ufs_mem_phy_lanes: phy@1d87400 {
				reg = <0 0x01d87400 0 0x108>,
				      <0 0x01d87600 0 0x1e0>,
				      <0 0x01d87c00 0 0x1dc>,
				      <0 0x01d87800 0 0x108>,
				      <0 0x01d87a00 0 0x1e0>;
				#phy-cells = <0>;
			};
		};

		ipa_virt: interconnect@1e00000 {
			compatible = "qcom,sm8250-ipa-virt";
			reg = <0 0x01e00000 0 0x1000>;
			#interconnect-cells = <1>;
			qcom,bcm-voters = <&apps_bcm_voter>;
		};

		tcsr_mutex: hwlock@1f40000 {
			compatible = "qcom,tcsr-mutex";
			reg = <0x0 0x01f40000 0x0 0x40000>;
			#hwlock-cells = <1>;
		};

		wsamacro: codec@3240000 {
			compatible = "qcom,sm8250-lpass-wsa-macro";
			reg = <0 0x03240000 0 0x1000>;
			clocks = <&audiocc LPASS_CDC_WSA_MCLK>,
				 <&audiocc LPASS_CDC_WSA_NPL>,
				 <&q6afecc LPASS_HW_MACRO_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
				 <&q6afecc LPASS_HW_DCODEC_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
				 <&aoncc LPASS_CDC_VA_MCLK>,
				 <&vamacro>;

			clock-names = "mclk", "npl", "macro", "dcodec", "va", "fsgen";

			#clock-cells = <0>;
			clock-frequency = <9600000>;
			clock-output-names = "mclk";
			#sound-dai-cells = <1>;

			pinctrl-names = "default";
			pinctrl-0 = <&wsa_swr_active>;
		};

		swr0: soundwire-controller@3250000 {
			reg = <0 0x03250000 0 0x2000>;
			compatible = "qcom,soundwire-v1.5.1";
			interrupts = <GIC_SPI 202 IRQ_TYPE_LEVEL_HIGH>;
			clocks = <&wsamacro>;
			clock-names = "iface";

			qcom,din-ports = <2>;
			qcom,dout-ports = <6>;

			qcom,ports-sinterval-low =	/bits/ 8 <0x07 0x1f 0x3f 0x07 0x1f 0x3f 0x0f 0x0f>;
			qcom,ports-offset1 =		/bits/ 8 <0x01 0x02 0x0c 0x06 0x12 0x0d 0x07 0x0a>;
			qcom,ports-offset2 =		/bits/ 8 <0xff 0x00 0x1f 0xff 0x00 0x1f 0x00 0x00>;
			qcom,ports-block-pack-mode =	/bits/ 8 <0x0 0x0 0x1 0x0 0x0 0x1 0x0 0x0>;

			#sound-dai-cells = <1>;
			#address-cells = <2>;
			#size-cells = <0>;
		};

		audiocc: clock-controller@3300000 {
			compatible = "qcom,sm8250-lpass-audiocc";
			reg = <0 0x03300000 0 0x30000>;
			#clock-cells = <1>;
			clocks = <&q6afecc LPASS_HW_MACRO_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
				<&q6afecc LPASS_HW_DCODEC_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
				<&q6afecc LPASS_CLK_ID_TX_CORE_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>;
			clock-names = "core", "audio", "bus";
		};

		vamacro: codec@3370000 {
			compatible = "qcom,sm8250-lpass-va-macro";
			reg = <0 0x03370000 0 0x1000>;
			clocks = <&aoncc LPASS_CDC_VA_MCLK>,
				<&q6afecc LPASS_HW_MACRO_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
				<&q6afecc LPASS_HW_DCODEC_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>;

			clock-names = "mclk", "macro", "dcodec";

			#clock-cells = <0>;
			clock-frequency = <9600000>;
			clock-output-names = "fsgen";
			#sound-dai-cells = <1>;
		};

		rxmacro: rxmacro@3200000 {
			pinctrl-names = "default";
			pinctrl-0 = <&rx_swr_active>;
			compatible = "qcom,sm8250-lpass-rx-macro";
			reg = <0 0x3200000 0 0x1000>;
			status = "disabled";

			clocks = <&q6afecc LPASS_CLK_ID_TX_CORE_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
				<&q6afecc LPASS_CLK_ID_TX_CORE_NPL_MCLK  LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
				<&q6afecc LPASS_HW_MACRO_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
				<&q6afecc LPASS_HW_DCODEC_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
				<&vamacro>;

			clock-names = "mclk", "npl", "macro", "dcodec", "fsgen";

			#clock-cells = <0>;
			clock-frequency = <9600000>;
			clock-output-names = "mclk";
			#sound-dai-cells = <1>;
		};

		swr1: soundwire-controller@3210000 {
			reg = <0 0x3210000 0 0x2000>;
			compatible = "qcom,soundwire-v1.5.1";
			status = "disabled";
			interrupts = <GIC_SPI 298 IRQ_TYPE_LEVEL_HIGH>;
			clocks = <&rxmacro>;
			clock-names = "iface";
			label = "RX";
			qcom,din-ports = <0>;
			qcom,dout-ports = <5>;

			qcom,ports-sinterval-low =	/bits/ 8 <0x03 0x1F 0x1F 0x07 0x00>;
			qcom,ports-offset1 =		/bits/ 8 <0x00 0x00 0x0B 0x01 0x00>;
			qcom,ports-offset2 =		/bits/ 8 <0x00 0x00 0x0B 0x00 0x00>;
			qcom,ports-hstart =		/bits/ 8 <0xFF 0x03 0xFF 0xFF 0xFF>;
			qcom,ports-hstop =		/bits/ 8 <0xFF 0x06 0xFF 0xFF 0xFF>;
			qcom,ports-word-length =	/bits/ 8 <0x01 0x07 0x04 0xFF 0xFF>;
			qcom,ports-block-pack-mode =	/bits/ 8 <0xFF 0x00 0x01 0xFF 0xFF>;
			qcom,ports-lane-control =	/bits/ 8 <0x01 0x00 0x00 0x00 0x00>;
			qcom,ports-block-group-count =	/bits/ 8 <0xFF 0xFF 0xFF 0xFF 0x00>;

			#sound-dai-cells = <1>;
			#address-cells = <2>;
			#size-cells = <0>;
		};

		txmacro: txmacro@3220000 {
			pinctrl-names = "default";
			pinctrl-0 = <&tx_swr_active>;
			compatible = "qcom,sm8250-lpass-tx-macro";
			reg = <0 0x3220000 0 0x1000>;
			status = "disabled";

			clocks = <&q6afecc LPASS_CLK_ID_TX_CORE_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
				 <&q6afecc LPASS_CLK_ID_TX_CORE_NPL_MCLK  LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
				 <&q6afecc LPASS_HW_MACRO_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
				 <&q6afecc LPASS_HW_DCODEC_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
				 <&vamacro>;

			clock-names = "mclk", "npl", "macro", "dcodec", "fsgen";

			#clock-cells = <0>;
			clock-frequency = <9600000>;
			clock-output-names = "mclk";
			#address-cells = <2>;
			#size-cells = <2>;
			#sound-dai-cells = <1>;
		};

		/* tx macro */
		swr2: soundwire-controller@3230000 {
			reg = <0 0x3230000 0 0x2000>;
			compatible = "qcom,soundwire-v1.5.1";
			interrupts-extended = <&intc GIC_SPI 297 IRQ_TYPE_LEVEL_HIGH>;
			interrupt-names = "core";
			status = "disabled";

			clocks = <&txmacro>;
			clock-names = "iface";
			label = "TX";

			qcom,din-ports = <5>;
			qcom,dout-ports = <0>;
			qcom,ports-sinterval-low =	/bits/ 8 <0xFF 0x01 0x01 0x03 0x03>;
			qcom,ports-offset1 =		/bits/ 8 <0xFF 0x01 0x00 0x02 0x00>;
			qcom,ports-offset2 =		/bits/ 8 <0xFF 0x00 0x00 0x00 0x00>;
			qcom,ports-block-pack-mode =	/bits/ 8 <0xFF 0xFF 0xFF 0xFF 0xFF>;
			qcom,ports-hstart =		/bits/ 8 <0xFF 0xFF 0xFF 0xFF 0xFF>;
			qcom,ports-hstop =		/bits/ 8 <0xFF 0xFF 0xFF 0xFF 0xFF>;
			qcom,ports-word-length =	/bits/ 8 <0xFF 0xFF 0xFF 0xFF 0xFF>;
			qcom,ports-block-group-count =	/bits/ 8 <0xFF 0xFF 0xFF 0xFF 0xFF>;
			qcom,ports-lane-control =	/bits/ 8 <0xFF 0x00 0x01 0x00 0x01>;
			qcom,port-offset = <1>;
			#sound-dai-cells = <1>;
			#address-cells = <2>;
			#size-cells = <0>;
		};

		aoncc: clock-controller@3380000 {
			compatible = "qcom,sm8250-lpass-aoncc";
			reg = <0 0x03380000 0 0x40000>;
			#clock-cells = <1>;
			clocks = <&q6afecc LPASS_HW_MACRO_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
				<&q6afecc LPASS_HW_DCODEC_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
				<&q6afecc LPASS_CLK_ID_TX_CORE_NPL_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>;
			clock-names = "core", "audio", "bus";
		};

		lpass_tlmm: pinctrl@33c0000{
			compatible = "qcom,sm8250-lpass-lpi-pinctrl";
			reg = <0 0x033c0000 0x0 0x20000>,
			      <0 0x03550000 0x0 0x10000>;
			gpio-controller;
			#gpio-cells = <2>;
			gpio-ranges = <&lpass_tlmm 0 0 14>;

			clocks = <&q6afecc LPASS_HW_MACRO_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
				<&q6afecc LPASS_HW_DCODEC_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>;
			clock-names = "core", "audio";

			wsa_swr_active: wsa-swr-active-pins {
				clk {
					pins = "gpio10";
					function = "wsa_swr_clk";
					drive-strength = <2>;
					slew-rate = <1>;
					bias-disable;
				};

				data {
					pins = "gpio11";
					function = "wsa_swr_data";
					drive-strength = <2>;
					slew-rate = <1>;
					bias-bus-hold;

				};
			};

			wsa_swr_sleep: wsa-swr-sleep-pins {
				clk {
					pins = "gpio10";
					function = "wsa_swr_clk";
					drive-strength = <2>;
					input-enable;
					bias-pull-down;
				};

				data {
					pins = "gpio11";
					function = "wsa_swr_data";
					drive-strength = <2>;
					input-enable;
					bias-pull-down;

				};
			};

			dmic01_active: dmic01-active-pins {
				clk {
					pins = "gpio6";
					function = "dmic1_clk";
					drive-strength = <8>;
					output-high;
				};
				data {
					pins = "gpio7";
					function = "dmic1_data";
					drive-strength = <8>;
					input-enable;
				};
			};

			dmic01_sleep: dmic01-sleep-pins {
				clk {
					pins = "gpio6";
					function = "dmic1_clk";
					drive-strength = <2>;
					bias-disable;
					output-low;
				};

				data {
					pins = "gpio7";
					function = "dmic1_data";
					drive-strength = <2>;
					pull-down;
					input-enable;
				};
			};

			rx_swr_active: rx_swr-active-pins {
				clk {
					pins = "gpio3";
					function = "swr_rx_clk";
					drive-strength = <2>;
					slew-rate = <1>;
					bias-disable;
				};

				data {
					pins = "gpio4", "gpio5";
					function = "swr_rx_data";
					drive-strength = <2>;
					slew-rate = <1>;
					bias-bus-hold;
				};
			};

			tx_swr_active: tx_swr-active-pins {
				clk {
					pins = "gpio0";
					function = "swr_tx_clk";
					drive-strength = <2>;
					slew-rate = <1>;
					bias-disable;
				};

				data {
					pins = "gpio1", "gpio2";
					function = "swr_tx_data";
					drive-strength = <2>;
					slew-rate = <1>;
					bias-bus-hold;
				};
			};

			tx_swr_sleep: tx_swr-sleep-pins {
				clk {
					pins = "gpio0";
					function = "swr_tx_clk";
					drive-strength = <2>;
					input-enable;
					bias-pull-down;
				};

				data1 {
					pins = "gpio1";
					function = "swr_tx_data";
					drive-strength = <2>;
					input-enable;
					bias-bus-hold;
				};

				data2 {
					pins = "gpio2";
					function = "swr_tx_data";
					drive-strength = <2>;
					input-enable;
					bias-pull-down;
				};
			};
		};

		gpu: gpu@3d00000 {
			compatible = "qcom,adreno-650.2",
				     "qcom,adreno";

			reg = <0 0x03d00000 0 0x40000>;
			reg-names = "kgsl_3d0_reg_memory";

			interrupts = <GIC_SPI 300 IRQ_TYPE_LEVEL_HIGH>;

			iommus = <&adreno_smmu 0 0x401>;

			operating-points-v2 = <&gpu_opp_table>;

			qcom,gmu = <&gmu>;

			status = "disabled";

			zap-shader {
				memory-region = <&gpu_mem>;
			};

			/* note: downstream checks gpu binning for 670 Mhz */
			gpu_opp_table: opp-table {
				compatible = "operating-points-v2";

				opp-670000000 {
					opp-hz = /bits/ 64 <670000000>;
					opp-level = <RPMH_REGULATOR_LEVEL_NOM_L1>;
				};

				opp-587000000 {
					opp-hz = /bits/ 64 <587000000>;
					opp-level = <RPMH_REGULATOR_LEVEL_NOM>;
				};

				opp-525000000 {
					opp-hz = /bits/ 64 <525000000>;
					opp-level = <RPMH_REGULATOR_LEVEL_SVS_L2>;
				};

				opp-490000000 {
					opp-hz = /bits/ 64 <490000000>;
					opp-level = <RPMH_REGULATOR_LEVEL_SVS_L1>;
				};

				opp-441600000 {
					opp-hz = /bits/ 64 <441600000>;
					opp-level = <RPMH_REGULATOR_LEVEL_SVS_L0>;
				};

				opp-400000000 {
					opp-hz = /bits/ 64 <400000000>;
					opp-level = <RPMH_REGULATOR_LEVEL_SVS>;
				};

				opp-305000000 {
					opp-hz = /bits/ 64 <305000000>;
					opp-level = <RPMH_REGULATOR_LEVEL_LOW_SVS>;
				};
			};
		};

		gmu: gmu@3d6a000 {
			compatible = "qcom,adreno-gmu-650.2", "qcom,adreno-gmu";

			reg = <0 0x03d6a000 0 0x30000>,
			      <0 0x3de0000 0 0x10000>,
			      <0 0xb290000 0 0x10000>,
			      <0 0xb490000 0 0x10000>;
			reg-names = "gmu", "rscc", "gmu_pdc", "gmu_pdc_seq";

			interrupts = <GIC_SPI 304 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 305 IRQ_TYPE_LEVEL_HIGH>;
			interrupt-names = "hfi", "gmu";

			clocks = <&gpucc GPU_CC_AHB_CLK>,
				 <&gpucc GPU_CC_CX_GMU_CLK>,
				 <&gpucc GPU_CC_CXO_CLK>,
				 <&gcc GCC_DDRSS_GPU_AXI_CLK>,
				 <&gcc GCC_GPU_MEMNOC_GFX_CLK>;
			clock-names = "ahb", "gmu", "cxo", "axi", "memnoc";

			power-domains = <&gpucc GPU_CX_GDSC>,
					<&gpucc GPU_GX_GDSC>;
			power-domain-names = "cx", "gx";

			iommus = <&adreno_smmu 5 0x400>;

			operating-points-v2 = <&gmu_opp_table>;

			status = "disabled";

			gmu_opp_table: opp-table {
				compatible = "operating-points-v2";

				opp-200000000 {
					opp-hz = /bits/ 64 <200000000>;
					opp-level = <RPMH_REGULATOR_LEVEL_MIN_SVS>;
				};
			};
		};

		gpucc: clock-controller@3d90000 {
			compatible = "qcom,sm8250-gpucc";
			reg = <0 0x03d90000 0 0x9000>;
			clocks = <&rpmhcc RPMH_CXO_CLK>,
				 <&gcc GCC_GPU_GPLL0_CLK_SRC>,
				 <&gcc GCC_GPU_GPLL0_DIV_CLK_SRC>;
			clock-names = "bi_tcxo",
				      "gcc_gpu_gpll0_clk_src",
				      "gcc_gpu_gpll0_div_clk_src";
			#clock-cells = <1>;
			#reset-cells = <1>;
			#power-domain-cells = <1>;
		};

		adreno_smmu: iommu@3da0000 {
			compatible = "qcom,sm8250-smmu-500", "qcom,adreno-smmu", "arm,mmu-500";
			reg = <0 0x03da0000 0 0x10000>;
			#iommu-cells = <2>;
			#global-interrupts = <2>;
			interrupts = <GIC_SPI 672 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 673 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 678 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 679 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 680 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 681 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 682 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 683 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 684 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 685 IRQ_TYPE_LEVEL_HIGH>;
			clocks = <&gpucc GPU_CC_AHB_CLK>,
				 <&gcc GCC_GPU_MEMNOC_GFX_CLK>,
				 <&gcc GCC_GPU_SNOC_DVM_GFX_CLK>;
			clock-names = "ahb", "bus", "iface";

			power-domains = <&gpucc GPU_CX_GDSC>;
		};

		slpi: remoteproc@5c00000 {
			compatible = "qcom,sm8250-slpi-pas";
			reg = <0 0x05c00000 0 0x4000>;

			interrupts-extended = <&pdc 9 IRQ_TYPE_LEVEL_HIGH>,
					      <&smp2p_slpi_in 0 IRQ_TYPE_EDGE_RISING>,
					      <&smp2p_slpi_in 1 IRQ_TYPE_EDGE_RISING>,
					      <&smp2p_slpi_in 2 IRQ_TYPE_EDGE_RISING>,
					      <&smp2p_slpi_in 3 IRQ_TYPE_EDGE_RISING>;
			interrupt-names = "wdog", "fatal", "ready",
					  "handover", "stop-ack";

			clocks = <&rpmhcc RPMH_CXO_CLK>;
			clock-names = "xo";

			power-domains = <&rpmhpd SM8250_LCX>,
					<&rpmhpd SM8250_LMX>;
			power-domain-names = "lcx", "lmx";

			memory-region = <&slpi_mem>;

			qcom,qmp = <&aoss_qmp>;

			qcom,smem-states = <&smp2p_slpi_out 0>;
			qcom,smem-state-names = "stop";

			status = "disabled";

			glink-edge {
				interrupts-extended = <&ipcc IPCC_CLIENT_SLPI
							     IPCC_MPROC_SIGNAL_GLINK_QMP
							     IRQ_TYPE_EDGE_RISING>;
				mboxes = <&ipcc IPCC_CLIENT_SLPI
						IPCC_MPROC_SIGNAL_GLINK_QMP>;

				label = "slpi";
				qcom,remote-pid = <3>;

				fastrpc {
					compatible = "qcom,fastrpc";
					qcom,glink-channels = "fastrpcglink-apps-dsp";
					label = "sdsp";
					qcom,non-secure-domain;
					#address-cells = <1>;
					#size-cells = <0>;

					compute-cb@1 {
						compatible = "qcom,fastrpc-compute-cb";
						reg = <1>;
						iommus = <&apps_smmu 0x0541 0x0>;
					};

					compute-cb@2 {
						compatible = "qcom,fastrpc-compute-cb";
						reg = <2>;
						iommus = <&apps_smmu 0x0542 0x0>;
					};

					compute-cb@3 {
						compatible = "qcom,fastrpc-compute-cb";
						reg = <3>;
						iommus = <&apps_smmu 0x0543 0x0>;
						/* note: shared-cb = <4> in downstream */
					};
				};
			};
		};

		cdsp: remoteproc@8300000 {
			compatible = "qcom,sm8250-cdsp-pas";
			reg = <0 0x08300000 0 0x10000>;

			interrupts-extended = <&intc GIC_SPI 578 IRQ_TYPE_LEVEL_HIGH>,
					      <&smp2p_cdsp_in 0 IRQ_TYPE_EDGE_RISING>,
					      <&smp2p_cdsp_in 1 IRQ_TYPE_EDGE_RISING>,
					      <&smp2p_cdsp_in 2 IRQ_TYPE_EDGE_RISING>,
					      <&smp2p_cdsp_in 3 IRQ_TYPE_EDGE_RISING>;
			interrupt-names = "wdog", "fatal", "ready",
					  "handover", "stop-ack";

			clocks = <&rpmhcc RPMH_CXO_CLK>;
			clock-names = "xo";

			power-domains = <&rpmhpd SM8250_CX>;

			memory-region = <&cdsp_mem>;

			qcom,qmp = <&aoss_qmp>;

			qcom,smem-states = <&smp2p_cdsp_out 0>;
			qcom,smem-state-names = "stop";

			status = "disabled";

			glink-edge {
				interrupts-extended = <&ipcc IPCC_CLIENT_CDSP
							     IPCC_MPROC_SIGNAL_GLINK_QMP
							     IRQ_TYPE_EDGE_RISING>;
				mboxes = <&ipcc IPCC_CLIENT_CDSP
						IPCC_MPROC_SIGNAL_GLINK_QMP>;

				label = "cdsp";
				qcom,remote-pid = <5>;

				fastrpc {
					compatible = "qcom,fastrpc";
					qcom,glink-channels = "fastrpcglink-apps-dsp";
					label = "cdsp";
					qcom,non-secure-domain;
					#address-cells = <1>;
					#size-cells = <0>;

					compute-cb@1 {
						compatible = "qcom,fastrpc-compute-cb";
						reg = <1>;
						iommus = <&apps_smmu 0x1001 0x0460>;
					};

					compute-cb@2 {
						compatible = "qcom,fastrpc-compute-cb";
						reg = <2>;
						iommus = <&apps_smmu 0x1002 0x0460>;
					};

					compute-cb@3 {
						compatible = "qcom,fastrpc-compute-cb";
						reg = <3>;
						iommus = <&apps_smmu 0x1003 0x0460>;
					};

					compute-cb@4 {
						compatible = "qcom,fastrpc-compute-cb";
						reg = <4>;
						iommus = <&apps_smmu 0x1004 0x0460>;
					};

					compute-cb@5 {
						compatible = "qcom,fastrpc-compute-cb";
						reg = <5>;
						iommus = <&apps_smmu 0x1005 0x0460>;
					};

					compute-cb@6 {
						compatible = "qcom,fastrpc-compute-cb";
						reg = <6>;
						iommus = <&apps_smmu 0x1006 0x0460>;
					};

					compute-cb@7 {
						compatible = "qcom,fastrpc-compute-cb";
						reg = <7>;
						iommus = <&apps_smmu 0x1007 0x0460>;
					};

					compute-cb@8 {
						compatible = "qcom,fastrpc-compute-cb";
						reg = <8>;
						iommus = <&apps_smmu 0x1008 0x0460>;
					};

					/* note: secure cb9 in downstream */
				};
			};
		};

		sound: sound {
		};

		usb_1_hsphy: phy@88e3000 {
			compatible = "qcom,sm8250-usb-hs-phy",
				     "qcom,usb-snps-hs-7nm-phy";
			reg = <0 0x088e3000 0 0x400>;
			status = "disabled";
			#phy-cells = <0>;

			clocks = <&rpmhcc RPMH_CXO_CLK>;
			clock-names = "ref";

			resets = <&gcc GCC_QUSB2PHY_PRIM_BCR>;
		};

		usb_2_hsphy: phy@88e4000 {
			compatible = "qcom,sm8250-usb-hs-phy",
				     "qcom,usb-snps-hs-7nm-phy";
			reg = <0 0x088e4000 0 0x400>;
			status = "disabled";
			#phy-cells = <0>;

			clocks = <&rpmhcc RPMH_CXO_CLK>;
			clock-names = "ref";

			resets = <&gcc GCC_QUSB2PHY_SEC_BCR>;
		};

		usb_1_qmpphy: phy@88e9000 {
			compatible = "qcom,sm8250-qmp-usb3-dp-phy";
			reg = <0 0x088e9000 0 0x200>,
			      <0 0x088e8000 0 0x40>,
			      <0 0x088ea000 0 0x200>;
			status = "disabled";
			#address-cells = <2>;
			#size-cells = <2>;
			ranges;

			clocks = <&gcc GCC_USB3_PRIM_PHY_AUX_CLK>,
				 <&rpmhcc RPMH_CXO_CLK>,
				 <&gcc GCC_USB3_PRIM_PHY_COM_AUX_CLK>;
			clock-names = "aux", "ref_clk_src", "com_aux";

			resets = <&gcc GCC_USB3_DP_PHY_PRIM_BCR>,
				 <&gcc GCC_USB3_PHY_PRIM_BCR>;
			reset-names = "phy", "common";

			usb_1_ssphy: usb3-phy@88e9200 {
				reg = <0 0x088e9200 0 0x200>,
				      <0 0x088e9400 0 0x200>,
				      <0 0x088e9c00 0 0x400>,
				      <0 0x088e9600 0 0x200>,
				      <0 0x088e9800 0 0x200>,
				      <0 0x088e9a00 0 0x100>;
				#clock-cells = <0>;
				#phy-cells = <0>;
				clocks = <&gcc GCC_USB3_PRIM_PHY_PIPE_CLK>;
				clock-names = "pipe0";
				clock-output-names = "usb3_phy_pipe_clk_src";
			};

			dp_phy: dp-phy@88ea200 {
				reg = <0 0x088ea200 0 0x200>,
				      <0 0x088ea400 0 0x200>,
				      <0 0x088eac00 0 0x400>,
				      <0 0x088ea600 0 0x200>,
				      <0 0x088ea800 0 0x200>,
				      <0 0x088eaa00 0 0x100>;
				#phy-cells = <0>;
				#clock-cells = <1>;
				clocks = <&gcc GCC_USB3_PRIM_PHY_PIPE_CLK>;
				clock-names = "pipe0";
				clock-output-names = "usb3_phy_pipe_clk_src";
			};
		};

		usb_2_qmpphy: phy@88eb000 {
			compatible = "qcom,sm8250-qmp-usb3-uni-phy";
			reg = <0 0x088eb000 0 0x200>;
			status = "disabled";
			#address-cells = <2>;
			#size-cells = <2>;
			ranges;

			clocks = <&gcc GCC_USB3_SEC_PHY_AUX_CLK>,
				 <&rpmhcc RPMH_CXO_CLK>,
				 <&gcc GCC_USB3_SEC_CLKREF_EN>,
				 <&gcc GCC_USB3_SEC_PHY_COM_AUX_CLK>;
			clock-names = "aux", "ref_clk_src", "ref", "com_aux";

			resets = <&gcc GCC_USB3PHY_PHY_SEC_BCR>,
				 <&gcc GCC_USB3_PHY_SEC_BCR>;
			reset-names = "phy", "common";

			usb_2_ssphy: phy@88eb200 {
				reg = <0 0x088eb200 0 0x200>,
				      <0 0x088eb400 0 0x200>,
				      <0 0x088eb800 0 0x800>;
				#clock-cells = <0>;
				#phy-cells = <0>;
				clocks = <&gcc GCC_USB3_SEC_PHY_PIPE_CLK>;
				clock-names = "pipe0";
				clock-output-names = "usb3_uni_phy_pipe_clk_src";
			};
		};

		sdhc_2: mmc@8804000 {
			compatible = "qcom,sm8250-sdhci", "qcom,sdhci-msm-v5";
			reg = <0 0x08804000 0 0x1000>;

			interrupts = <GIC_SPI 204 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 222 IRQ_TYPE_LEVEL_HIGH>;
			interrupt-names = "hc_irq", "pwr_irq";

			clocks = <&gcc GCC_SDCC2_AHB_CLK>,
				 <&gcc GCC_SDCC2_APPS_CLK>,
				 <&rpmhcc RPMH_CXO_CLK>;
			clock-names = "iface", "core", "xo";
			iommus = <&apps_smmu 0x4a0 0x0>;
			qcom,dll-config = <0x0007642c>;
			qcom,ddr-config = <0x80040868>;
			power-domains = <&rpmhpd SM8250_CX>;
			operating-points-v2 = <&sdhc2_opp_table>;

			status = "disabled";

			sdhc2_opp_table: opp-table {
				compatible = "operating-points-v2";

				opp-19200000 {
					opp-hz = /bits/ 64 <19200000>;
					required-opps = <&rpmhpd_opp_min_svs>;
				};

				opp-50000000 {
					opp-hz = /bits/ 64 <50000000>;
					required-opps = <&rpmhpd_opp_low_svs>;
				};

				opp-100000000 {
					opp-hz = /bits/ 64 <100000000>;
					required-opps = <&rpmhpd_opp_svs>;
				};

				opp-202000000 {
					opp-hz = /bits/ 64 <202000000>;
					required-opps = <&rpmhpd_opp_svs_l1>;
				};
			};
		};

		dc_noc: interconnect@90c0000 {
			compatible = "qcom,sm8250-dc-noc";
			reg = <0 0x090c0000 0 0x4200>;
			#interconnect-cells = <1>;
			qcom,bcm-voters = <&apps_bcm_voter>;
		};

		gem_noc: interconnect@9100000 {
			compatible = "qcom,sm8250-gem-noc";
			reg = <0 0x09100000 0 0xb4000>;
			#interconnect-cells = <1>;
			qcom,bcm-voters = <&apps_bcm_voter>;
		};

		npu_noc: interconnect@9990000 {
			compatible = "qcom,sm8250-npu-noc";
			reg = <0 0x09990000 0 0x1600>;
			#interconnect-cells = <1>;
			qcom,bcm-voters = <&apps_bcm_voter>;
		};

		usb_1: usb@a6f8800 {
			compatible = "qcom,sm8250-dwc3", "qcom,dwc3";
			reg = <0 0x0a6f8800 0 0x400>;
			status = "disabled";
			#address-cells = <2>;
			#size-cells = <2>;
			ranges;
			dma-ranges;

			clocks = <&gcc GCC_CFG_NOC_USB3_PRIM_AXI_CLK>,
				 <&gcc GCC_USB30_PRIM_MASTER_CLK>,
				 <&gcc GCC_AGGRE_USB3_PRIM_AXI_CLK>,
				 <&gcc GCC_USB30_PRIM_SLEEP_CLK>,
				 <&gcc GCC_USB30_PRIM_MOCK_UTMI_CLK>,
				 <&gcc GCC_USB3_SEC_CLKREF_EN>;
			clock-names = "cfg_noc",
				      "core",
				      "iface",
				      "sleep",
				      "mock_utmi",
				      "xo";

			assigned-clocks = <&gcc GCC_USB30_PRIM_MOCK_UTMI_CLK>,
					  <&gcc GCC_USB30_PRIM_MASTER_CLK>;
			assigned-clock-rates = <19200000>, <200000000>;

			interrupts-extended = <&intc GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>,
					      <&pdc 17 IRQ_TYPE_LEVEL_HIGH>,
					      <&pdc 15 IRQ_TYPE_EDGE_BOTH>,
					      <&pdc 14 IRQ_TYPE_EDGE_BOTH>;
			interrupt-names = "hs_phy_irq",
					  "ss_phy_irq",
					  "dm_hs_phy_irq",
					  "dp_hs_phy_irq";

			power-domains = <&gcc USB30_PRIM_GDSC>;

			resets = <&gcc GCC_USB30_PRIM_BCR>;

			usb_1_dwc3: usb@a600000 {
				compatible = "snps,dwc3";
				reg = <0 0x0a600000 0 0xcd00>;
				interrupts = <GIC_SPI 133 IRQ_TYPE_LEVEL_HIGH>;
				iommus = <&apps_smmu 0x0 0x0>;
				snps,dis_u2_susphy_quirk;
				snps,dis_enblslpm_quirk;
				phys = <&usb_1_hsphy>, <&usb_1_ssphy>;
				phy-names = "usb2-phy", "usb3-phy";
			};
		};

		system-cache-controller@9200000 {
			compatible = "qcom,sm8250-llcc";
			reg = <0 0x09200000 0 0x1d0000>, <0 0x09600000 0 0x50000>;
			reg-names = "llcc_base", "llcc_broadcast_base";
		};

		usb_2: usb@a8f8800 {
			compatible = "qcom,sm8250-dwc3", "qcom,dwc3";
			reg = <0 0x0a8f8800 0 0x400>;
			status = "disabled";
			#address-cells = <2>;
			#size-cells = <2>;
			ranges;
			dma-ranges;

			clocks = <&gcc GCC_CFG_NOC_USB3_SEC_AXI_CLK>,
				 <&gcc GCC_USB30_SEC_MASTER_CLK>,
				 <&gcc GCC_AGGRE_USB3_SEC_AXI_CLK>,
				 <&gcc GCC_USB30_SEC_SLEEP_CLK>,
				 <&gcc GCC_USB30_SEC_MOCK_UTMI_CLK>,
				 <&gcc GCC_USB3_SEC_CLKREF_EN>;
			clock-names = "cfg_noc",
				      "core",
				      "iface",
				      "sleep",
				      "mock_utmi",
				      "xo";

			assigned-clocks = <&gcc GCC_USB30_SEC_MOCK_UTMI_CLK>,
					  <&gcc GCC_USB30_SEC_MASTER_CLK>;
			assigned-clock-rates = <19200000>, <200000000>;

			interrupts-extended = <&intc GIC_SPI 136 IRQ_TYPE_LEVEL_HIGH>,
					      <&pdc 16 IRQ_TYPE_LEVEL_HIGH>,
					      <&pdc 13 IRQ_TYPE_EDGE_BOTH>,
					      <&pdc 12 IRQ_TYPE_EDGE_BOTH>;
			interrupt-names = "hs_phy_irq",
					  "ss_phy_irq",
					  "dm_hs_phy_irq",
					  "dp_hs_phy_irq";

			power-domains = <&gcc USB30_SEC_GDSC>;

			resets = <&gcc GCC_USB30_SEC_BCR>;

			usb_2_dwc3: usb@a800000 {
				compatible = "snps,dwc3";
				reg = <0 0x0a800000 0 0xcd00>;
				interrupts = <GIC_SPI 138 IRQ_TYPE_LEVEL_HIGH>;
				iommus = <&apps_smmu 0x20 0>;
				snps,dis_u2_susphy_quirk;
				snps,dis_enblslpm_quirk;
				phys = <&usb_2_hsphy>, <&usb_2_ssphy>;
				phy-names = "usb2-phy", "usb3-phy";
			};
		};

		venus: video-codec@aa00000 {
			compatible = "qcom,sm8250-venus";
			reg = <0 0x0aa00000 0 0x100000>;
			interrupts = <GIC_SPI 174 IRQ_TYPE_LEVEL_HIGH>;
			power-domains = <&videocc MVS0C_GDSC>,
					<&videocc MVS0_GDSC>,
					<&rpmhpd SM8250_MX>;
			power-domain-names = "venus", "vcodec0", "mx";
			operating-points-v2 = <&venus_opp_table>;

			clocks = <&gcc GCC_VIDEO_AXI0_CLK>,
				 <&videocc VIDEO_CC_MVS0C_CLK>,
				 <&videocc VIDEO_CC_MVS0_CLK>;
			clock-names = "iface", "core", "vcodec0_core";

			interconnects = <&gem_noc MASTER_AMPSS_M0 &config_noc SLAVE_VENUS_CFG>,
					<&mmss_noc MASTER_VIDEO_P0 &mc_virt SLAVE_EBI_CH0>;
			interconnect-names = "cpu-cfg", "video-mem";

			iommus = <&apps_smmu 0x2100 0x0400>;
			memory-region = <&video_mem>;

			resets = <&gcc GCC_VIDEO_AXI0_CLK_ARES>,
				 <&videocc VIDEO_CC_MVS0C_CLK_ARES>;
			reset-names = "bus", "core";

			status = "disabled";

			video-decoder {
				compatible = "venus-decoder";
			};

			video-encoder {
				compatible = "venus-encoder";
			};

			venus_opp_table: opp-table {
				compatible = "operating-points-v2";

				opp-720000000 {
					opp-hz = /bits/ 64 <720000000>;
					required-opps = <&rpmhpd_opp_low_svs>;
				};

				opp-1014000000 {
					opp-hz = /bits/ 64 <1014000000>;
					required-opps = <&rpmhpd_opp_svs>;
				};

				opp-1098000000 {
					opp-hz = /bits/ 64 <1098000000>;
					required-opps = <&rpmhpd_opp_svs_l1>;
				};

				opp-1332000000 {
					opp-hz = /bits/ 64 <1332000000>;
					required-opps = <&rpmhpd_opp_nom>;
				};
			};
		};

		videocc: clock-controller@abf0000 {
			compatible = "qcom,sm8250-videocc";
			reg = <0 0x0abf0000 0 0x10000>;
			clocks = <&gcc GCC_VIDEO_AHB_CLK>,
				 <&rpmhcc RPMH_CXO_CLK>,
				 <&rpmhcc RPMH_CXO_CLK_A>;
			power-domains = <&rpmhpd SM8250_MMCX>;
			required-opps = <&rpmhpd_opp_low_svs>;
			clock-names = "iface", "bi_tcxo", "bi_tcxo_ao";
			#clock-cells = <1>;
			#reset-cells = <1>;
			#power-domain-cells = <1>;
		};

		cci0: cci@ac4f000 {
			compatible = "qcom,sm8250-cci";
			#address-cells = <1>;
			#size-cells = <0>;

			reg = <0 0x0ac4f000 0 0x1000>;
			interrupts = <GIC_SPI 460 IRQ_TYPE_EDGE_RISING>;
			power-domains = <&camcc TITAN_TOP_GDSC>;

			clocks = <&camcc CAM_CC_CAMNOC_AXI_CLK>,
				 <&camcc CAM_CC_SLOW_AHB_CLK_SRC>,
				 <&camcc CAM_CC_CPAS_AHB_CLK>,
				 <&camcc CAM_CC_CCI_0_CLK>,
				 <&camcc CAM_CC_CCI_0_CLK_SRC>;
			clock-names = "camnoc_axi",
				      "slow_ahb_src",
				      "cpas_ahb",
				      "cci",
				      "cci_src";

			pinctrl-0 = <&cci0_default>;
			pinctrl-1 = <&cci0_sleep>;
			pinctrl-names = "default", "sleep";

			status = "disabled";

			cci0_i2c0: i2c-bus@0 {
				reg = <0>;
				clock-frequency = <1000000>;
				#address-cells = <1>;
				#size-cells = <0>;
			};

			cci0_i2c1: i2c-bus@1 {
				reg = <1>;
				clock-frequency = <1000000>;
				#address-cells = <1>;
				#size-cells = <0>;
			};
		};

		cci1: cci@ac50000 {
			compatible = "qcom,sm8250-cci";
			#address-cells = <1>;
			#size-cells = <0>;

			reg = <0 0x0ac50000 0 0x1000>;
			interrupts = <GIC_SPI 271 IRQ_TYPE_EDGE_RISING>;
			power-domains = <&camcc TITAN_TOP_GDSC>;

			clocks = <&camcc CAM_CC_CAMNOC_AXI_CLK>,
				 <&camcc CAM_CC_SLOW_AHB_CLK_SRC>,
				 <&camcc CAM_CC_CPAS_AHB_CLK>,
				 <&camcc CAM_CC_CCI_1_CLK>,
				 <&camcc CAM_CC_CCI_1_CLK_SRC>;
			clock-names = "camnoc_axi",
				      "slow_ahb_src",
				      "cpas_ahb",
				      "cci",
				      "cci_src";

			pinctrl-0 = <&cci1_default>;
			pinctrl-1 = <&cci1_sleep>;
			pinctrl-names = "default", "sleep";

			status = "disabled";

			cci1_i2c0: i2c-bus@0 {
				reg = <0>;
				clock-frequency = <1000000>;
				#address-cells = <1>;
				#size-cells = <0>;
			};

			cci1_i2c1: i2c-bus@1 {
				reg = <1>;
				clock-frequency = <1000000>;
				#address-cells = <1>;
				#size-cells = <0>;
			};
		};

		camss: camss@ac6a000 {
			compatible = "qcom,sm8250-camss";
			status = "disabled";

			reg = <0 0xac6a000 0 0x2000>,
			      <0 0xac6c000 0 0x2000>,
			      <0 0xac6e000 0 0x1000>,
			      <0 0xac70000 0 0x1000>,
			      <0 0xac72000 0 0x1000>,
			      <0 0xac74000 0 0x1000>,
			      <0 0xacb4000 0 0xd000>,
			      <0 0xacc3000 0 0xd000>,
			      <0 0xacd9000 0 0x2200>,
			      <0 0xacdb200 0 0x2200>;
			reg-names = "csiphy0",
				    "csiphy1",
				    "csiphy2",
				    "csiphy3",
				    "csiphy4",
				    "csiphy5",
				    "vfe0",
				    "vfe1",
				    "vfe_lite0",
				    "vfe_lite1";

			interrupts = <GIC_SPI 477 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 478 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 479 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 448 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 464 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 466 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 468 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 359 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 465 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 467 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 469 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 360 IRQ_TYPE_LEVEL_HIGH>;
			interrupt-names = "csiphy0",
					  "csiphy1",
					  "csiphy2",
					  "csiphy3",
					  "csiphy4",
					  "csiphy5",
					  "csid0",
					  "csid1",
					  "csid2",
					  "csid3",
					  "vfe0",
					  "vfe1",
					  "vfe_lite0",
					  "vfe_lite1";

			power-domains = <&camcc IFE_0_GDSC>,
					<&camcc IFE_1_GDSC>,
					<&camcc TITAN_TOP_GDSC>;

			clocks = <&gcc GCC_CAMERA_AHB_CLK>,
				 <&gcc GCC_CAMERA_HF_AXI_CLK>,
				 <&gcc GCC_CAMERA_SF_AXI_CLK>,
				 <&camcc CAM_CC_CAMNOC_AXI_CLK>,
				 <&camcc CAM_CC_CAMNOC_AXI_CLK_SRC>,
				 <&camcc CAM_CC_CORE_AHB_CLK>,
				 <&camcc CAM_CC_CPAS_AHB_CLK>,
				 <&camcc CAM_CC_CSIPHY0_CLK>,
				 <&camcc CAM_CC_CSI0PHYTIMER_CLK>,
				 <&camcc CAM_CC_CSIPHY1_CLK>,
				 <&camcc CAM_CC_CSI1PHYTIMER_CLK>,
				 <&camcc CAM_CC_CSIPHY2_CLK>,
				 <&camcc CAM_CC_CSI2PHYTIMER_CLK>,
				 <&camcc CAM_CC_CSIPHY3_CLK>,
				 <&camcc CAM_CC_CSI3PHYTIMER_CLK>,
				 <&camcc CAM_CC_CSIPHY4_CLK>,
				 <&camcc CAM_CC_CSI4PHYTIMER_CLK>,
				 <&camcc CAM_CC_CSIPHY5_CLK>,
				 <&camcc CAM_CC_CSI5PHYTIMER_CLK>,
				 <&camcc CAM_CC_SLOW_AHB_CLK_SRC>,
				 <&camcc CAM_CC_IFE_0_AHB_CLK>,
				 <&camcc CAM_CC_IFE_0_AXI_CLK>,
				 <&camcc CAM_CC_IFE_0_CLK>,
				 <&camcc CAM_CC_IFE_0_CPHY_RX_CLK>,
				 <&camcc CAM_CC_IFE_0_CSID_CLK>,
				 <&camcc CAM_CC_IFE_0_AREG_CLK>,
				 <&camcc CAM_CC_IFE_1_AHB_CLK>,
				 <&camcc CAM_CC_IFE_1_AXI_CLK>,
				 <&camcc CAM_CC_IFE_1_CLK>,
				 <&camcc CAM_CC_IFE_1_CPHY_RX_CLK>,
				 <&camcc CAM_CC_IFE_1_CSID_CLK>,
				 <&camcc CAM_CC_IFE_1_AREG_CLK>,
				 <&camcc CAM_CC_IFE_LITE_AHB_CLK>,
				 <&camcc CAM_CC_IFE_LITE_AXI_CLK>,
				 <&camcc CAM_CC_IFE_LITE_CLK>,
				 <&camcc CAM_CC_IFE_LITE_CPHY_RX_CLK>,
				 <&camcc CAM_CC_IFE_LITE_CSID_CLK>;

			clock-names = "cam_ahb_clk",
				      "cam_hf_axi",
				      "cam_sf_axi",
				      "camnoc_axi",
				      "camnoc_axi_src",
				      "core_ahb",
				      "cpas_ahb",
				      "csiphy0",
				      "csiphy0_timer",
				      "csiphy1",
				      "csiphy1_timer",
				      "csiphy2",
				      "csiphy2_timer",
				      "csiphy3",
				      "csiphy3_timer",
				      "csiphy4",
				      "csiphy4_timer",
				      "csiphy5",
				      "csiphy5_timer",
				      "slow_ahb_src",
				      "vfe0_ahb",
				      "vfe0_axi",
				      "vfe0",
				      "vfe0_cphy_rx",
				      "vfe0_csid",
				      "vfe0_areg",
				      "vfe1_ahb",
				      "vfe1_axi",
				      "vfe1",
				      "vfe1_cphy_rx",
				      "vfe1_csid",
				      "vfe1_areg",
				      "vfe_lite_ahb",
				      "vfe_lite_axi",
				      "vfe_lite",
				      "vfe_lite_cphy_rx",
				      "vfe_lite_csid";

			iommus = <&apps_smmu 0x800 0x400>,
				 <&apps_smmu 0x801 0x400>,
				 <&apps_smmu 0x840 0x400>,
				 <&apps_smmu 0x841 0x400>,
				 <&apps_smmu 0xc00 0x400>,
				 <&apps_smmu 0xc01 0x400>,
				 <&apps_smmu 0xc40 0x400>,
				 <&apps_smmu 0xc41 0x400>;

			interconnects = <&gem_noc MASTER_AMPSS_M0 &config_noc SLAVE_CAMERA_CFG>,
					<&mmss_noc MASTER_CAMNOC_HF &mc_virt SLAVE_EBI_CH0>,
					<&mmss_noc MASTER_CAMNOC_SF &mc_virt SLAVE_EBI_CH0>,
					<&mmss_noc MASTER_CAMNOC_ICP &mc_virt SLAVE_EBI_CH0>;
			interconnect-names = "cam_ahb",
					     "cam_hf_0_mnoc",
					     "cam_sf_0_mnoc",
					     "cam_sf_icp_mnoc";
		};

		camcc: clock-controller@ad00000 {
			compatible = "qcom,sm8250-camcc";
			reg = <0 0x0ad00000 0 0x10000>;
			clocks = <&gcc GCC_CAMERA_AHB_CLK>,
				 <&rpmhcc RPMH_CXO_CLK>,
				 <&rpmhcc RPMH_CXO_CLK_A>,
				 <&sleep_clk>;
			clock-names = "iface", "bi_tcxo", "bi_tcxo_ao", "sleep_clk";
			power-domains = <&rpmhpd SM8250_MMCX>;
			required-opps = <&rpmhpd_opp_low_svs>;
			status = "disabled";
			#clock-cells = <1>;
			#reset-cells = <1>;
			#power-domain-cells = <1>;
		};

		mdss: mdss@ae00000 {
			compatible = "qcom,sm8250-mdss";
			reg = <0 0x0ae00000 0 0x1000>;
			reg-names = "mdss";

			interconnects = <&mmss_noc MASTER_MDP_PORT0 &mc_virt SLAVE_EBI_CH0>,
					<&mmss_noc MASTER_MDP_PORT1 &mc_virt SLAVE_EBI_CH0>;
			interconnect-names = "mdp0-mem", "mdp1-mem";

			power-domains = <&dispcc MDSS_GDSC>;

			clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>,
				 <&gcc GCC_DISP_HF_AXI_CLK>,
				 <&gcc GCC_DISP_SF_AXI_CLK>,
				 <&dispcc DISP_CC_MDSS_MDP_CLK>;
			clock-names = "iface", "bus", "nrt_bus", "core";

			interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>;
			interrupt-controller;
			#interrupt-cells = <1>;

			iommus = <&apps_smmu 0x820 0x402>;

			status = "disabled";

			#address-cells = <2>;
			#size-cells = <2>;
			ranges;

			mdss_mdp: display-controller@ae01000 {
				compatible = "qcom,sm8250-dpu";
				reg = <0 0x0ae01000 0 0x8f000>,
				      <0 0x0aeb0000 0 0x2008>;
				reg-names = "mdp", "vbif";

				clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>,
					 <&gcc GCC_DISP_HF_AXI_CLK>,
					 <&dispcc DISP_CC_MDSS_MDP_CLK>,
					 <&dispcc DISP_CC_MDSS_VSYNC_CLK>;
				clock-names = "iface", "bus", "core", "vsync";

				assigned-clocks = <&dispcc DISP_CC_MDSS_VSYNC_CLK>;
				assigned-clock-rates = <19200000>;

				operating-points-v2 = <&mdp_opp_table>;
				power-domains = <&rpmhpd SM8250_MMCX>;

				interrupt-parent = <&mdss>;
				interrupts = <0>;

				ports {
					#address-cells = <1>;
					#size-cells = <0>;

					port@0 {
						reg = <0>;
						dpu_intf1_out: endpoint {
							remote-endpoint = <&dsi0_in>;
						};
					};

					port@1 {
						reg = <1>;
						dpu_intf2_out: endpoint {
							remote-endpoint = <&dsi1_in>;
						};
					};
				};

				mdp_opp_table: opp-table {
					compatible = "operating-points-v2";

					opp-200000000 {
						opp-hz = /bits/ 64 <200000000>;
						required-opps = <&rpmhpd_opp_low_svs>;
					};

					opp-300000000 {
						opp-hz = /bits/ 64 <300000000>;
						required-opps = <&rpmhpd_opp_svs>;
					};

					opp-345000000 {
						opp-hz = /bits/ 64 <345000000>;
						required-opps = <&rpmhpd_opp_svs_l1>;
					};

					opp-460000000 {
						opp-hz = /bits/ 64 <460000000>;
						required-opps = <&rpmhpd_opp_nom>;
					};
				};
			};

			dsi0: dsi@ae94000 {
				compatible = "qcom,mdss-dsi-ctrl";
				reg = <0 0x0ae94000 0 0x400>;
				reg-names = "dsi_ctrl";

				interrupt-parent = <&mdss>;
				interrupts = <4>;

				clocks = <&dispcc DISP_CC_MDSS_BYTE0_CLK>,
					 <&dispcc DISP_CC_MDSS_BYTE0_INTF_CLK>,
					 <&dispcc DISP_CC_MDSS_PCLK0_CLK>,
					 <&dispcc DISP_CC_MDSS_ESC0_CLK>,
					 <&dispcc DISP_CC_MDSS_AHB_CLK>,
					<&gcc GCC_DISP_HF_AXI_CLK>;
				clock-names = "byte",
					      "byte_intf",
					      "pixel",
					      "core",
					      "iface",
					      "bus";

				assigned-clocks = <&dispcc DISP_CC_MDSS_BYTE0_CLK_SRC>, <&dispcc DISP_CC_MDSS_PCLK0_CLK_SRC>;
				assigned-clock-parents = <&dsi0_phy 0>, <&dsi0_phy 1>;

				operating-points-v2 = <&dsi_opp_table>;
				power-domains = <&rpmhpd SM8250_MMCX>;

				phys = <&dsi0_phy>;

				status = "disabled";

				#address-cells = <1>;
				#size-cells = <0>;

				ports {
					#address-cells = <1>;
					#size-cells = <0>;

					port@0 {
						reg = <0>;
						dsi0_in: endpoint {
							remote-endpoint = <&dpu_intf1_out>;
						};
					};

					port@1 {
						reg = <1>;
						dsi0_out: endpoint {
						};
					};
				};

				dsi_opp_table: opp-table {
					compatible = "operating-points-v2";

					opp-187500000 {
						opp-hz = /bits/ 64 <187500000>;
						required-opps = <&rpmhpd_opp_low_svs>;
					};

					opp-300000000 {
						opp-hz = /bits/ 64 <300000000>;
						required-opps = <&rpmhpd_opp_svs>;
					};

					opp-358000000 {
						opp-hz = /bits/ 64 <358000000>;
						required-opps = <&rpmhpd_opp_svs_l1>;
					};
				};
			};

			dsi0_phy: phy@ae94400 {
				compatible = "qcom,dsi-phy-7nm";
				reg = <0 0x0ae94400 0 0x200>,
				      <0 0x0ae94600 0 0x280>,
				      <0 0x0ae94900 0 0x260>;
				reg-names = "dsi_phy",
					    "dsi_phy_lane",
					    "dsi_pll";

				#clock-cells = <1>;
				#phy-cells = <0>;

				clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>,
					 <&rpmhcc RPMH_CXO_CLK>;
				clock-names = "iface", "ref";

				status = "disabled";
			};

			dsi1: dsi@ae96000 {
				compatible = "qcom,mdss-dsi-ctrl";
				reg = <0 0x0ae96000 0 0x400>;
				reg-names = "dsi_ctrl";

				interrupt-parent = <&mdss>;
				interrupts = <5>;

				clocks = <&dispcc DISP_CC_MDSS_BYTE1_CLK>,
					 <&dispcc DISP_CC_MDSS_BYTE1_INTF_CLK>,
					 <&dispcc DISP_CC_MDSS_PCLK1_CLK>,
					 <&dispcc DISP_CC_MDSS_ESC1_CLK>,
					 <&dispcc DISP_CC_MDSS_AHB_CLK>,
					 <&gcc GCC_DISP_HF_AXI_CLK>;
				clock-names = "byte",
					      "byte_intf",
					      "pixel",
					      "core",
					      "iface",
					      "bus";

				assigned-clocks = <&dispcc DISP_CC_MDSS_BYTE1_CLK_SRC>, <&dispcc DISP_CC_MDSS_PCLK1_CLK_SRC>;
				assigned-clock-parents = <&dsi1_phy 0>, <&dsi1_phy 1>;

				operating-points-v2 = <&dsi_opp_table>;
				power-domains = <&rpmhpd SM8250_MMCX>;

				phys = <&dsi1_phy>;

				status = "disabled";

				#address-cells = <1>;
				#size-cells = <0>;

				ports {
					#address-cells = <1>;
					#size-cells = <0>;

					port@0 {
						reg = <0>;
						dsi1_in: endpoint {
							remote-endpoint = <&dpu_intf2_out>;
						};
					};

					port@1 {
						reg = <1>;
						dsi1_out: endpoint {
						};
					};
				};
			};

			dsi1_phy: phy@ae96400 {
				compatible = "qcom,dsi-phy-7nm";
				reg = <0 0x0ae96400 0 0x200>,
				      <0 0x0ae96600 0 0x280>,
				      <0 0x0ae96900 0 0x260>;
				reg-names = "dsi_phy",
					    "dsi_phy_lane",
					    "dsi_pll";

				#clock-cells = <1>;
				#phy-cells = <0>;

				clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>,
					 <&rpmhcc RPMH_CXO_CLK>;
				clock-names = "iface", "ref";

				status = "disabled";
			};
		};

		dispcc: clock-controller@af00000 {
			compatible = "qcom,sm8250-dispcc";
			reg = <0 0x0af00000 0 0x10000>;
			power-domains = <&rpmhpd SM8250_MMCX>;
			required-opps = <&rpmhpd_opp_low_svs>;
			clocks = <&rpmhcc RPMH_CXO_CLK>,
				 <&dsi0_phy 0>,
				 <&dsi0_phy 1>,
				 <&dsi1_phy 0>,
				 <&dsi1_phy 1>,
				 <&dp_phy 0>,
				 <&dp_phy 1>;
			clock-names = "bi_tcxo",
				      "dsi0_phy_pll_out_byteclk",
				      "dsi0_phy_pll_out_dsiclk",
				      "dsi1_phy_pll_out_byteclk",
				      "dsi1_phy_pll_out_dsiclk",
				      "dp_phy_pll_link_clk",
				      "dp_phy_pll_vco_div_clk";
			#clock-cells = <1>;
			#reset-cells = <1>;
			#power-domain-cells = <1>;
		};

		pdc: interrupt-controller@b220000 {
			compatible = "qcom,sm8250-pdc", "qcom,pdc";
			reg = <0 0x0b220000 0 0x30000>, <0 0x17c000f0 0 0x60>;
			qcom,pdc-ranges = <0 480 94>, <94 609 31>,
					  <125 63 1>, <126 716 12>;
			#interrupt-cells = <2>;
			interrupt-parent = <&intc>;
			interrupt-controller;
		};

		tsens0: thermal-sensor@c263000 {
			compatible = "qcom,sm8250-tsens", "qcom,tsens-v2";
			reg = <0 0x0c263000 0 0x1ff>, /* TM */
			      <0 0x0c222000 0 0x1ff>; /* SROT */
			#qcom,sensors = <16>;
			interrupts = <GIC_SPI 506 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 508 IRQ_TYPE_LEVEL_HIGH>;
			interrupt-names = "uplow", "critical";
			#thermal-sensor-cells = <1>;
		};

		tsens1: thermal-sensor@c265000 {
			compatible = "qcom,sm8250-tsens", "qcom,tsens-v2";
			reg = <0 0x0c265000 0 0x1ff>, /* TM */
			      <0 0x0c223000 0 0x1ff>; /* SROT */
			#qcom,sensors = <9>;
			interrupts = <GIC_SPI 507 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 509 IRQ_TYPE_LEVEL_HIGH>;
			interrupt-names = "uplow", "critical";
			#thermal-sensor-cells = <1>;
		};

		aoss_qmp: power-controller@c300000 {
			compatible = "qcom,sm8250-aoss-qmp", "qcom,aoss-qmp";
			reg = <0 0x0c300000 0 0x400>;
			interrupts-extended = <&ipcc IPCC_CLIENT_AOP
						     IPCC_MPROC_SIGNAL_GLINK_QMP
						     IRQ_TYPE_EDGE_RISING>;
			mboxes = <&ipcc IPCC_CLIENT_AOP
					IPCC_MPROC_SIGNAL_GLINK_QMP>;

			#clock-cells = <0>;
		};

		sram@c3f0000 {
			compatible = "qcom,rpmh-stats";
			reg = <0 0x0c3f0000 0 0x400>;
		};

		spmi_bus: spmi@c440000 {
			compatible = "qcom,spmi-pmic-arb";
			reg = <0x0 0x0c440000 0x0 0x0001100>,
			      <0x0 0x0c600000 0x0 0x2000000>,
			      <0x0 0x0e600000 0x0 0x0100000>,
			      <0x0 0x0e700000 0x0 0x00a0000>,
			      <0x0 0x0c40a000 0x0 0x0026000>;
			reg-names = "core", "chnls", "obsrvr", "intr", "cnfg";
			interrupt-names = "periph_irq";
			interrupts-extended = <&pdc 1 IRQ_TYPE_LEVEL_HIGH>;
			qcom,ee = <0>;
			qcom,channel = <0>;
			#address-cells = <2>;
			#size-cells = <0>;
			interrupt-controller;
			#interrupt-cells = <4>;
		};

		tlmm: pinctrl@f100000 {
			compatible = "qcom,sm8250-pinctrl";
			reg = <0 0x0f100000 0 0x300000>,
			      <0 0x0f500000 0 0x300000>,
			      <0 0x0f900000 0 0x300000>;
			reg-names = "west", "south", "north";
			interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
			gpio-controller;
			#gpio-cells = <2>;
			interrupt-controller;
			#interrupt-cells = <2>;
			gpio-ranges = <&tlmm 0 0 181>;
			wakeup-parent = <&pdc>;

			cci0_default: cci0-default-state {
				cci0_i2c0_default: cci0-i2c0-default-pins {
					/* SDA, SCL */
					pins = "gpio101", "gpio102";
					function = "cci_i2c";

					bias-pull-up;
					drive-strength = <2>; /* 2 mA */
				};

				cci0_i2c1_default: cci0-i2c1-default-pins {
					/* SDA, SCL */
					pins = "gpio103", "gpio104";
					function = "cci_i2c";

					bias-pull-up;
					drive-strength = <2>; /* 2 mA */
				};
			};

			cci0_sleep: cci0-sleep-state {
				cci0_i2c0_sleep: cci0-i2c0-sleep-pins {
					/* SDA, SCL */
					pins = "gpio101", "gpio102";
					function = "cci_i2c";

					drive-strength = <2>; /* 2 mA */
					bias-pull-down;
				};

				cci0_i2c1_sleep: cci0-i2c1-sleep-pins {
					/* SDA, SCL */
					pins = "gpio103", "gpio104";
					function = "cci_i2c";

					drive-strength = <2>; /* 2 mA */
					bias-pull-down;
				};
			};

			cci1_default: cci1-default-state {
				cci1_i2c0_default: cci1-i2c0-default-pins {
					/* SDA, SCL */
					pins = "gpio105","gpio106";
					function = "cci_i2c";

					bias-pull-up;
					drive-strength = <2>; /* 2 mA */
				};

				cci1_i2c1_default: cci1-i2c1-default-pins {
					/* SDA, SCL */
					pins = "gpio107","gpio108";
					function = "cci_i2c";

					bias-pull-up;
					drive-strength = <2>; /* 2 mA */
				};
			};

			cci1_sleep: cci1-sleep-state {
				cci1_i2c0_sleep: cci1-i2c0-sleep-pins {
					/* SDA, SCL */
					pins = "gpio105","gpio106";
					function = "cci_i2c";

					bias-pull-down;
					drive-strength = <2>; /* 2 mA */
				};

				cci1_i2c1_sleep: cci1-i2c1-sleep-pins {
					/* SDA, SCL */
					pins = "gpio107","gpio108";
					function = "cci_i2c";

					bias-pull-down;
					drive-strength = <2>; /* 2 mA */
				};
			};

			pri_mi2s_active: pri-mi2s-active-state {
				sclk-pins {
					pins = "gpio138";
					function = "mi2s0_sck";
					drive-strength = <8>;
					bias-disable;
				};

				ws-pins {
					pins = "gpio141";
					function = "mi2s0_ws";
					drive-strength = <8>;
					output-high;
				};

				data0-pins {
					pins = "gpio139";
					function = "mi2s0_data0";
					drive-strength = <8>;
					bias-disable;
					output-high;
				};

				data1-pins {
					pins = "gpio140";
					function = "mi2s0_data1";
					drive-strength = <8>;
					output-high;
				};
			};

			qup_i2c0_default: qup-i2c0-default-state {
				pins = "gpio28", "gpio29";
				function = "qup0";
				drive-strength = <2>;
				bias-disable;
			};

			qup_i2c1_default: qup-i2c1-default-state {
				pins = "gpio4", "gpio5";
				function = "qup1";
				drive-strength = <2>;
				bias-disable;
			};

			qup_i2c2_default: qup-i2c2-default-state {
				pins = "gpio115", "gpio116";
				function = "qup2";
				drive-strength = <2>;
				bias-disable;
			};

			qup_i2c3_default: qup-i2c3-default-state {
				pins = "gpio119", "gpio120";
				function = "qup3";
				drive-strength = <2>;
				bias-disable;
			};

			qup_i2c4_default: qup-i2c4-default-state {
				pins = "gpio8", "gpio9";
				function = "qup4";
				drive-strength = <2>;
				bias-disable;
			};

			qup_i2c5_default: qup-i2c5-default-state {
				pins = "gpio12", "gpio13";
				function = "qup5";
				drive-strength = <2>;
				bias-disable;
			};

			qup_i2c6_default: qup-i2c6-default-state {
				pins = "gpio16", "gpio17";
				function = "qup6";
				drive-strength = <2>;
				bias-disable;
			};

			qup_i2c7_default: qup-i2c7-default-state {
				pins = "gpio20", "gpio21";
				function = "qup7";
				drive-strength = <2>;
				bias-disable;
			};

			qup_i2c8_default: qup-i2c8-default-state {
				pins = "gpio24", "gpio25";
				function = "qup8";
				drive-strength = <2>;
				bias-disable;
			};

			qup_i2c9_default: qup-i2c9-default-state {
				pins = "gpio125", "gpio126";
				function = "qup9";
				drive-strength = <2>;
				bias-disable;
			};

			qup_i2c10_default: qup-i2c10-default-state {
				pins = "gpio129", "gpio130";
				function = "qup10";
				drive-strength = <2>;
				bias-disable;
			};

			qup_i2c11_default: qup-i2c11-default-state {
				pins = "gpio60", "gpio61";
				function = "qup11";
				drive-strength = <2>;
				bias-disable;
			};

			qup_i2c12_default: qup-i2c12-default-state {
				pins = "gpio32", "gpio33";
				function = "qup12";
				drive-strength = <2>;
				bias-disable;
			};

			qup_i2c13_default: qup-i2c13-default-state {
				pins = "gpio36", "gpio37";
				function = "qup13";
				drive-strength = <2>;
				bias-disable;
			};

			qup_i2c14_default: qup-i2c14-default-state {
				pins = "gpio40", "gpio41";
				function = "qup14";
				drive-strength = <2>;
				bias-disable;
			};

			qup_i2c15_default: qup-i2c15-default-state {
				pins = "gpio44", "gpio45";
				function = "qup15";
				drive-strength = <2>;
				bias-disable;
			};

			qup_i2c16_default: qup-i2c16-default-state {
				pins = "gpio48", "gpio49";
				function = "qup16";
				drive-strength = <2>;
				bias-disable;
			};

			qup_i2c17_default: qup-i2c17-default-state {
				pins = "gpio52", "gpio53";
				function = "qup17";
				drive-strength = <2>;
				bias-disable;
			};

			qup_i2c18_default: qup-i2c18-default-state {
				pins = "gpio56", "gpio57";
				function = "qup18";
				drive-strength = <2>;
				bias-disable;
			};

			qup_i2c19_default: qup-i2c19-default-state {
				pins = "gpio0", "gpio1";
				function = "qup19";
				drive-strength = <2>;
				bias-disable;
			};

			qup_spi0_cs: qup-spi0-cs-state {
				pins = "gpio31";
				function = "qup0";
			};

			qup_spi0_cs_gpio: qup-spi0-cs-gpio-state {
				pins = "gpio31";
				function = "gpio";
			};

			qup_spi0_data_clk: qup-spi0-data-clk-state {
				pins = "gpio28", "gpio29",
				       "gpio30";
				function = "qup0";
			};

			qup_spi1_cs: qup-spi1-cs-state {
				pins = "gpio7";
				function = "qup1";
			};

			qup_spi1_cs_gpio: qup-spi1-cs-gpio-state {
				pins = "gpio7";
				function = "gpio";
			};

			qup_spi1_data_clk: qup-spi1-data-clk-state {
				pins = "gpio4", "gpio5",
				       "gpio6";
				function = "qup1";
			};

			qup_spi2_cs: qup-spi2-cs-state {
				pins = "gpio118";
				function = "qup2";
			};

			qup_spi2_cs_gpio: qup-spi2-cs-gpio-state {
				pins = "gpio118";
				function = "gpio";
			};

			qup_spi2_data_clk: qup-spi2-data-clk-state {
				pins = "gpio115", "gpio116",
				       "gpio117";
				function = "qup2";
			};

			qup_spi3_cs: qup-spi3-cs-state {
				pins = "gpio122";
				function = "qup3";
			};

			qup_spi3_cs_gpio: qup-spi3-cs-gpio-state {
				pins = "gpio122";
				function = "gpio";
			};

			qup_spi3_data_clk: qup-spi3-data-clk-state {
				pins = "gpio119", "gpio120",
				       "gpio121";
				function = "qup3";
			};

			qup_spi4_cs: qup-spi4-cs-state {
				pins = "gpio11";
				function = "qup4";
			};

			qup_spi4_cs_gpio: qup-spi4-cs-gpio-state {
				pins = "gpio11";
				function = "gpio";
			};

			qup_spi4_data_clk: qup-spi4-data-clk-state {
				pins = "gpio8", "gpio9",
				       "gpio10";
				function = "qup4";
			};

			qup_spi5_cs: qup-spi5-cs-state {
				pins = "gpio15";
				function = "qup5";
			};

			qup_spi5_cs_gpio: qup-spi5-cs-gpio-state {
				pins = "gpio15";
				function = "gpio";
			};

			qup_spi5_data_clk: qup-spi5-data-clk-state {
				pins = "gpio12", "gpio13",
				       "gpio14";
				function = "qup5";
			};

			qup_spi6_cs: qup-spi6-cs-state {
				pins = "gpio19";
				function = "qup6";
			};

			qup_spi6_cs_gpio: qup-spi6-cs-gpio-state {
				pins = "gpio19";
				function = "gpio";
			};

			qup_spi6_data_clk: qup-spi6-data-clk-state {
				pins = "gpio16", "gpio17",
				       "gpio18";
				function = "qup6";
			};

			qup_spi7_cs: qup-spi7-cs-state {
				pins = "gpio23";
				function = "qup7";
			};

			qup_spi7_cs_gpio: qup-spi7-cs-gpio-state {
				pins = "gpio23";
				function = "gpio";
			};

			qup_spi7_data_clk: qup-spi7-data-clk-state {
				pins = "gpio20", "gpio21",
				       "gpio22";
				function = "qup7";
			};

			qup_spi8_cs: qup-spi8-cs-state {
				pins = "gpio27";
				function = "qup8";
			};

			qup_spi8_cs_gpio: qup-spi8-cs-gpio-state {
				pins = "gpio27";
				function = "gpio";
			};

			qup_spi8_data_clk: qup-spi8-data-clk-state {
				pins = "gpio24", "gpio25",
				       "gpio26";
				function = "qup8";
			};

			qup_spi9_cs: qup-spi9-cs-state {
				pins = "gpio128";
				function = "qup9";
			};

			qup_spi9_cs_gpio: qup-spi9-cs-gpio-state {
				pins = "gpio128";
				function = "gpio";
			};

			qup_spi9_data_clk: qup-spi9-data-clk-state {
				pins = "gpio125", "gpio126",
				       "gpio127";
				function = "qup9";
			};

			qup_spi10_cs: qup-spi10-cs-state {
				pins = "gpio132";
				function = "qup10";
			};

			qup_spi10_cs_gpio: qup-spi10-cs-gpio-state {
				pins = "gpio132";
				function = "gpio";
			};

			qup_spi10_data_clk: qup-spi10-data-clk-state {
				pins = "gpio129", "gpio130",
				       "gpio131";
				function = "qup10";
			};

			qup_spi11_cs: qup-spi11-cs-state {
				pins = "gpio63";
				function = "qup11";
			};

			qup_spi11_cs_gpio: qup-spi11-cs-gpio-state {
				pins = "gpio63";
				function = "gpio";
			};

			qup_spi11_data_clk: qup-spi11-data-clk-state {
				pins = "gpio60", "gpio61",
				       "gpio62";
				function = "qup11";
			};

			qup_spi12_cs: qup-spi12-cs-state {
				pins = "gpio35";
				function = "qup12";
			};

			qup_spi12_cs_gpio: qup-spi12-cs-gpio-state {
				pins = "gpio35";
				function = "gpio";
			};

			qup_spi12_data_clk: qup-spi12-data-clk-state {
				pins = "gpio32", "gpio33",
				       "gpio34";
				function = "qup12";
			};

			qup_spi13_cs: qup-spi13-cs-state {
				pins = "gpio39";
				function = "qup13";
			};

			qup_spi13_cs_gpio: qup-spi13-cs-gpio-state {
				pins = "gpio39";
				function = "gpio";
			};

			qup_spi13_data_clk: qup-spi13-data-clk-state {
				pins = "gpio36", "gpio37",
				       "gpio38";
				function = "qup13";
			};

			qup_spi14_cs: qup-spi14-cs-state {
				pins = "gpio43";
				function = "qup14";
			};

			qup_spi14_cs_gpio: qup-spi14-cs-gpio-state {
				pins = "gpio43";
				function = "gpio";
			};

			qup_spi14_data_clk: qup-spi14-data-clk-state {
				pins = "gpio40", "gpio41",
				       "gpio42";
				function = "qup14";
			};

			qup_spi15_cs: qup-spi15-cs-state {
				pins = "gpio47";
				function = "qup15";
			};

			qup_spi15_cs_gpio: qup-spi15-cs-gpio-state {
				pins = "gpio47";
				function = "gpio";
			};

			qup_spi15_data_clk: qup-spi15-data-clk-state {
				pins = "gpio44", "gpio45",
				       "gpio46";
				function = "qup15";
			};

			qup_spi16_cs: qup-spi16-cs-state {
				pins = "gpio51";
				function = "qup16";
			};

			qup_spi16_cs_gpio: qup-spi16-cs-gpio-state {
				pins = "gpio51";
				function = "gpio";
			};

			qup_spi16_data_clk: qup-spi16-data-clk-state {
				pins = "gpio48", "gpio49",
				       "gpio50";
				function = "qup16";
			};

			qup_spi17_cs: qup-spi17-cs-state {
				pins = "gpio55";
				function = "qup17";
			};

			qup_spi17_cs_gpio: qup-spi17-cs-gpio-state {
				pins = "gpio55";
				function = "gpio";
			};

			qup_spi17_data_clk: qup-spi17-data-clk-state {
				pins = "gpio52", "gpio53",
				       "gpio54";
				function = "qup17";
			};

			qup_spi18_cs: qup-spi18-cs-state {
				pins = "gpio59";
				function = "qup18";
			};

			qup_spi18_cs_gpio: qup-spi18-cs-gpio-state {
				pins = "gpio59";
				function = "gpio";
			};

			qup_spi18_data_clk: qup-spi18-data-clk-state {
				pins = "gpio56", "gpio57",
				       "gpio58";
				function = "qup18";
			};

			qup_spi19_cs: qup-spi19-cs-state {
				pins = "gpio3";
				function = "qup19";
			};

			qup_spi19_cs_gpio: qup-spi19-cs-gpio-state {
				pins = "gpio3";
				function = "gpio";
			};

			qup_spi19_data_clk: qup-spi19-data-clk-state {
				pins = "gpio0", "gpio1",
				       "gpio2";
				function = "qup19";
			};

			qup_uart2_default: qup-uart2-default-state {
				pins = "gpio117", "gpio118";
				function = "qup2";
			};

			qup_uart6_default: qup-uart6-default-state {
				pins = "gpio16", "gpio17", "gpio18", "gpio19";
				function = "qup6";
			};

			qup_uart12_default: qup-uart12-default-state {
				pins = "gpio34", "gpio35";
				function = "qup12";
			};

			qup_uart17_default: qup-uart17-default-state {
				pins = "gpio52", "gpio53", "gpio54", "gpio55";
				function = "qup17";
			};

			qup_uart18_default: qup-uart18-default-state {
				pins = "gpio58", "gpio59";
				function = "qup18";
			};

			tert_mi2s_active: tert-mi2s-active-state {
				sck-pins {
					pins = "gpio133";
					function = "mi2s2_sck";
					drive-strength = <8>;
					bias-disable;
				};

				data0-pins {
					pins = "gpio134";
					function = "mi2s2_data0";
					drive-strength = <8>;
					bias-disable;
					output-high;
				};

				ws-pins {
					pins = "gpio135";
					function = "mi2s2_ws";
					drive-strength = <8>;
					output-high;
				};
			};

			sdc2_sleep_state: sdc2-sleep-state {
				clk-pins {
					pins = "sdc2_clk";
					drive-strength = <2>;
					bias-disable;
				};

				cmd-pins {
					pins = "sdc2_cmd";
					drive-strength = <2>;
					bias-pull-up;
				};

				data-pins {
					pins = "sdc2_data";
					drive-strength = <2>;
					bias-pull-up;
				};
			};

			pcie0_default_state: pcie0-default-state {
				perst-pins {
					pins = "gpio79";
					function = "gpio";
					drive-strength = <2>;
					bias-pull-down;
				};

				clkreq-pins {
					pins = "gpio80";
					function = "pci_e0";
					drive-strength = <2>;
					bias-pull-up;
				};

				wake-pins {
					pins = "gpio81";
					function = "gpio";
					drive-strength = <2>;
					bias-pull-up;
				};
			};

			pcie1_default_state: pcie1-default-state {
				perst-pins {
					pins = "gpio82";
					function = "gpio";
					drive-strength = <2>;
					bias-pull-down;
				};

				clkreq-pins {
					pins = "gpio83";
					function = "pci_e1";
					drive-strength = <2>;
					bias-pull-up;
				};

				wake-pins {
					pins = "gpio84";
					function = "gpio";
					drive-strength = <2>;
					bias-pull-up;
				};
			};

			pcie2_default_state: pcie2-default-state {
				perst-pins {
					pins = "gpio85";
					function = "gpio";
					drive-strength = <2>;
					bias-pull-down;
				};

				clkreq-pins {
					pins = "gpio86";
					function = "pci_e2";
					drive-strength = <2>;
					bias-pull-up;
				};

				wake-pins {
					pins = "gpio87";
					function = "gpio";
					drive-strength = <2>;
					bias-pull-up;
				};
			};
		};

		apps_smmu: iommu@15000000 {
			compatible = "qcom,sm8250-smmu-500", "arm,mmu-500";
			reg = <0 0x15000000 0 0x100000>;
			#iommu-cells = <2>;
			#global-interrupts = <2>;
			interrupts =    <GIC_SPI 64 IRQ_TYPE_LEVEL_HIGH>,
					<GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>,
					<GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>,
					<GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>,
					<GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>,
					<GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>,
					<GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>,
					<GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>,
					<GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>,
					<GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>,
					<GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>,
					<GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>,
					<GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>,
					<GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>,
					<GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>,
					<GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>,
					<GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>,
					<GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH>,
					<GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>,
					<GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>,
					<GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>,
					<GIC_SPI 116 IRQ_TYPE_LEVEL_HIGH>,
					<GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>,
					<GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>,
					<GIC_SPI 181 IRQ_TYPE_LEVEL_HIGH>,
					<GIC_SPI 182 IRQ_TYPE_LEVEL_HIGH>,
					<GIC_SPI 183 IRQ_TYPE_LEVEL_HIGH>,
					<GIC_SPI 184 IRQ_TYPE_LEVEL_HIGH>,
					<GIC_SPI 185 IRQ_TYPE_LEVEL_HIGH>,
					<GIC_SPI 186 IRQ_TYPE_LEVEL_HIGH>,
					<GIC_SPI 187 IRQ_TYPE_LEVEL_HIGH>,
					<GIC_SPI 188 IRQ_TYPE_LEVEL_HIGH>,
					<GIC_SPI 189 IRQ_TYPE_LEVEL_HIGH>,
					<GIC_SPI 190 IRQ_TYPE_LEVEL_HIGH>,
					<GIC_SPI 191 IRQ_TYPE_LEVEL_HIGH>,
					<GIC_SPI 192 IRQ_TYPE_LEVEL_HIGH>,
					<GIC_SPI 315 IRQ_TYPE_LEVEL_HIGH>,
					<GIC_SPI 316 IRQ_TYPE_LEVEL_HIGH>,
					<GIC_SPI 317 IRQ_TYPE_LEVEL_HIGH>,
					<GIC_SPI 318 IRQ_TYPE_LEVEL_HIGH>,
					<GIC_SPI 319 IRQ_TYPE_LEVEL_HIGH>,
					<GIC_SPI 320 IRQ_TYPE_LEVEL_HIGH>,
					<GIC_SPI 321 IRQ_TYPE_LEVEL_HIGH>,
					<GIC_SPI 322 IRQ_TYPE_LEVEL_HIGH>,
					<GIC_SPI 323 IRQ_TYPE_LEVEL_HIGH>,
					<GIC_SPI 324 IRQ_TYPE_LEVEL_HIGH>,
					<GIC_SPI 325 IRQ_TYPE_LEVEL_HIGH>,
					<GIC_SPI 326 IRQ_TYPE_LEVEL_HIGH>,
					<GIC_SPI 327 IRQ_TYPE_LEVEL_HIGH>,
					<GIC_SPI 328 IRQ_TYPE_LEVEL_HIGH>,
					<GIC_SPI 329 IRQ_TYPE_LEVEL_HIGH>,
					<GIC_SPI 330 IRQ_TYPE_LEVEL_HIGH>,
					<GIC_SPI 331 IRQ_TYPE_LEVEL_HIGH>,
					<GIC_SPI 332 IRQ_TYPE_LEVEL_HIGH>,
					<GIC_SPI 333 IRQ_TYPE_LEVEL_HIGH>,
					<GIC_SPI 334 IRQ_TYPE_LEVEL_HIGH>,
					<GIC_SPI 335 IRQ_TYPE_LEVEL_HIGH>,
					<GIC_SPI 336 IRQ_TYPE_LEVEL_HIGH>,
					<GIC_SPI 337 IRQ_TYPE_LEVEL_HIGH>,
					<GIC_SPI 338 IRQ_TYPE_LEVEL_HIGH>,
					<GIC_SPI 339 IRQ_TYPE_LEVEL_HIGH>,
					<GIC_SPI 340 IRQ_TYPE_LEVEL_HIGH>,
					<GIC_SPI 341 IRQ_TYPE_LEVEL_HIGH>,
					<GIC_SPI 342 IRQ_TYPE_LEVEL_HIGH>,
					<GIC_SPI 343 IRQ_TYPE_LEVEL_HIGH>,
					<GIC_SPI 344 IRQ_TYPE_LEVEL_HIGH>,
					<GIC_SPI 345 IRQ_TYPE_LEVEL_HIGH>,
					<GIC_SPI 395 IRQ_TYPE_LEVEL_HIGH>,
					<GIC_SPI 396 IRQ_TYPE_LEVEL_HIGH>,
					<GIC_SPI 397 IRQ_TYPE_LEVEL_HIGH>,
					<GIC_SPI 398 IRQ_TYPE_LEVEL_HIGH>,
					<GIC_SPI 399 IRQ_TYPE_LEVEL_HIGH>,
					<GIC_SPI 400 IRQ_TYPE_LEVEL_HIGH>,
					<GIC_SPI 401 IRQ_TYPE_LEVEL_HIGH>,
					<GIC_SPI 402 IRQ_TYPE_LEVEL_HIGH>,
					<GIC_SPI 403 IRQ_TYPE_LEVEL_HIGH>,
					<GIC_SPI 404 IRQ_TYPE_LEVEL_HIGH>,
					<GIC_SPI 405 IRQ_TYPE_LEVEL_HIGH>,
					<GIC_SPI 406 IRQ_TYPE_LEVEL_HIGH>,
					<GIC_SPI 407 IRQ_TYPE_LEVEL_HIGH>,
					<GIC_SPI 408 IRQ_TYPE_LEVEL_HIGH>,
					<GIC_SPI 409 IRQ_TYPE_LEVEL_HIGH>,
					<GIC_SPI 412 IRQ_TYPE_LEVEL_HIGH>,
					<GIC_SPI 418 IRQ_TYPE_LEVEL_HIGH>,
					<GIC_SPI 419 IRQ_TYPE_LEVEL_HIGH>,
					<GIC_SPI 421 IRQ_TYPE_LEVEL_HIGH>,
					<GIC_SPI 423 IRQ_TYPE_LEVEL_HIGH>,
					<GIC_SPI 424 IRQ_TYPE_LEVEL_HIGH>,
					<GIC_SPI 425 IRQ_TYPE_LEVEL_HIGH>,
					<GIC_SPI 690 IRQ_TYPE_LEVEL_HIGH>,
					<GIC_SPI 691 IRQ_TYPE_LEVEL_HIGH>,
					<GIC_SPI 692 IRQ_TYPE_LEVEL_HIGH>,
					<GIC_SPI 693 IRQ_TYPE_LEVEL_HIGH>,
					<GIC_SPI 694 IRQ_TYPE_LEVEL_HIGH>,
					<GIC_SPI 695 IRQ_TYPE_LEVEL_HIGH>,
					<GIC_SPI 696 IRQ_TYPE_LEVEL_HIGH>,
					<GIC_SPI 697 IRQ_TYPE_LEVEL_HIGH>,
					<GIC_SPI 707 IRQ_TYPE_LEVEL_HIGH>;
		};

		adsp: remoteproc@17300000 {
			compatible = "qcom,sm8250-adsp-pas";
			reg = <0 0x17300000 0 0x100>;

			interrupts-extended = <&pdc 6 IRQ_TYPE_LEVEL_HIGH>,
					      <&smp2p_adsp_in 0 IRQ_TYPE_EDGE_RISING>,
					      <&smp2p_adsp_in 1 IRQ_TYPE_EDGE_RISING>,
					      <&smp2p_adsp_in 2 IRQ_TYPE_EDGE_RISING>,
					      <&smp2p_adsp_in 3 IRQ_TYPE_EDGE_RISING>;
			interrupt-names = "wdog", "fatal", "ready",
					  "handover", "stop-ack";

			clocks = <&rpmhcc RPMH_CXO_CLK>;
			clock-names = "xo";

			power-domains = <&rpmhpd SM8250_LCX>,
					<&rpmhpd SM8250_LMX>;
			power-domain-names = "lcx", "lmx";

			memory-region = <&adsp_mem>;

			qcom,qmp = <&aoss_qmp>;

			qcom,smem-states = <&smp2p_adsp_out 0>;
			qcom,smem-state-names = "stop";

			status = "disabled";

			glink-edge {
				interrupts-extended = <&ipcc IPCC_CLIENT_LPASS
							     IPCC_MPROC_SIGNAL_GLINK_QMP
							     IRQ_TYPE_EDGE_RISING>;
				mboxes = <&ipcc IPCC_CLIENT_LPASS
						IPCC_MPROC_SIGNAL_GLINK_QMP>;

				label = "lpass";
				qcom,remote-pid = <2>;

				apr {
					compatible = "qcom,apr-v2";
					qcom,glink-channels = "apr_audio_svc";
					qcom,domain = <APR_DOMAIN_ADSP>;
					#address-cells = <1>;
					#size-cells = <0>;

					service@3 {
						reg = <APR_SVC_ADSP_CORE>;
						compatible = "qcom,q6core";
						qcom,protection-domain = "avs/audio", "msm/adsp/audio_pd";
					};

					q6afe: service@4 {
						compatible = "qcom,q6afe";
						reg = <APR_SVC_AFE>;
						qcom,protection-domain = "avs/audio", "msm/adsp/audio_pd";
						q6afedai: dais {
							compatible = "qcom,q6afe-dais";
							#address-cells = <1>;
							#size-cells = <0>;
							#sound-dai-cells = <1>;
						};

						q6afecc: clock-controller {
							compatible = "qcom,q6afe-clocks";
							#clock-cells = <2>;
						};
					};

					q6asm: service@7 {
						compatible = "qcom,q6asm";
						reg = <APR_SVC_ASM>;
						qcom,protection-domain = "avs/audio", "msm/adsp/audio_pd";
						q6asmdai: dais {
							compatible = "qcom,q6asm-dais";
							#address-cells = <1>;
							#size-cells = <0>;
							#sound-dai-cells = <1>;
							iommus = <&apps_smmu 0x1801 0x0>;
						};
					};

					q6adm: service@8 {
						compatible = "qcom,q6adm";
						reg = <APR_SVC_ADM>;
						qcom,protection-domain = "avs/audio", "msm/adsp/audio_pd";
						q6routing: routing {
							compatible = "qcom,q6adm-routing";
							#sound-dai-cells = <0>;
						};
					};
				};

				fastrpc {
					compatible = "qcom,fastrpc";
					qcom,glink-channels = "fastrpcglink-apps-dsp";
					label = "adsp";
					qcom,non-secure-domain;
					#address-cells = <1>;
					#size-cells = <0>;

					compute-cb@3 {
						compatible = "qcom,fastrpc-compute-cb";
						reg = <3>;
						iommus = <&apps_smmu 0x1803 0x0>;
					};

					compute-cb@4 {
						compatible = "qcom,fastrpc-compute-cb";
						reg = <4>;
						iommus = <&apps_smmu 0x1804 0x0>;
					};

					compute-cb@5 {
						compatible = "qcom,fastrpc-compute-cb";
						reg = <5>;
						iommus = <&apps_smmu 0x1805 0x0>;
					};
				};
			};
		};

		intc: interrupt-controller@17a00000 {
			compatible = "arm,gic-v3";
			#interrupt-cells = <3>;
			interrupt-controller;
			reg = <0x0 0x17a00000 0x0 0x10000>,     /* GICD */
			      <0x0 0x17a60000 0x0 0x100000>;    /* GICR * 8 */
			interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>;
		};

		watchdog@17c10000 {
			compatible = "qcom,apss-wdt-sm8250", "qcom,kpss-wdt";
			reg = <0 0x17c10000 0 0x1000>;
			clocks = <&sleep_clk>;
			interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>;
		};

		timer@17c20000 {
			#address-cells = <1>;
			#size-cells = <1>;
			ranges = <0 0 0 0x20000000>;
			compatible = "arm,armv7-timer-mem";
			reg = <0x0 0x17c20000 0x0 0x1000>;
			clock-frequency = <19200000>;

			frame@17c21000 {
				frame-number = <0>;
				interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
					     <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
				reg = <0x17c21000 0x1000>,
				      <0x17c22000 0x1000>;
			};

			frame@17c23000 {
				frame-number = <1>;
				interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
				reg = <0x17c23000 0x1000>;
				status = "disabled";
			};

			frame@17c25000 {
				frame-number = <2>;
				interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
				reg = <0x17c25000 0x1000>;
				status = "disabled";
			};

			frame@17c27000 {
				frame-number = <3>;
				interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>;
				reg = <0x17c27000 0x1000>;
				status = "disabled";
			};

			frame@17c29000 {
				frame-number = <4>;
				interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
				reg = <0x17c29000 0x1000>;
				status = "disabled";
			};

			frame@17c2b000 {
				frame-number = <5>;
				interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
				reg = <0x17c2b000 0x1000>;
				status = "disabled";
			};

			frame@17c2d000 {
				frame-number = <6>;
				interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
				reg = <0x17c2d000 0x1000>;
				status = "disabled";
			};
		};

		apps_rsc: rsc@18200000 {
			label = "apps_rsc";
			compatible = "qcom,rpmh-rsc";
			reg = <0x0 0x18200000 0x0 0x10000>,
				<0x0 0x18210000 0x0 0x10000>,
				<0x0 0x18220000 0x0 0x10000>;
			reg-names = "drv-0", "drv-1", "drv-2";
			interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>;
			qcom,tcs-offset = <0xd00>;
			qcom,drv-id = <2>;
			qcom,tcs-config = <ACTIVE_TCS  2>, <SLEEP_TCS   3>,
					  <WAKE_TCS    3>, <CONTROL_TCS 1>;

			rpmhcc: clock-controller {
				compatible = "qcom,sm8250-rpmh-clk";
				#clock-cells = <1>;
				clock-names = "xo";
				clocks = <&xo_board>;
			};

			rpmhpd: power-controller {
				compatible = "qcom,sm8250-rpmhpd";
				#power-domain-cells = <1>;
				operating-points-v2 = <&rpmhpd_opp_table>;

				rpmhpd_opp_table: opp-table {
					compatible = "operating-points-v2";

					rpmhpd_opp_ret: opp1 {
						opp-level = <RPMH_REGULATOR_LEVEL_RETENTION>;
					};

					rpmhpd_opp_min_svs: opp2 {
						opp-level = <RPMH_REGULATOR_LEVEL_MIN_SVS>;
					};

					rpmhpd_opp_low_svs: opp3 {
						opp-level = <RPMH_REGULATOR_LEVEL_LOW_SVS>;
					};

					rpmhpd_opp_svs: opp4 {
						opp-level = <RPMH_REGULATOR_LEVEL_SVS>;
					};

					rpmhpd_opp_svs_l1: opp5 {
						opp-level = <RPMH_REGULATOR_LEVEL_SVS_L1>;
					};

					rpmhpd_opp_nom: opp6 {
						opp-level = <RPMH_REGULATOR_LEVEL_NOM>;
					};

					rpmhpd_opp_nom_l1: opp7 {
						opp-level = <RPMH_REGULATOR_LEVEL_NOM_L1>;
					};

					rpmhpd_opp_nom_l2: opp8 {
						opp-level = <RPMH_REGULATOR_LEVEL_NOM_L2>;
					};

					rpmhpd_opp_turbo: opp9 {
						opp-level = <RPMH_REGULATOR_LEVEL_TURBO>;
					};

					rpmhpd_opp_turbo_l1: opp10 {
						opp-level = <RPMH_REGULATOR_LEVEL_TURBO_L1>;
					};
				};
			};

			apps_bcm_voter: bcm-voter {
				compatible = "qcom,bcm-voter";
			};
		};

		epss_l3: interconnect@18590000 {
			compatible = "qcom,sm8250-epss-l3";
			reg = <0 0x18590000 0 0x1000>;

			clocks = <&rpmhcc RPMH_CXO_CLK>, <&gcc GPLL0>;
			clock-names = "xo", "alternate";

			#interconnect-cells = <1>;
		};

		cpufreq_hw: cpufreq@18591000 {
			compatible = "qcom,sm8250-cpufreq-epss", "qcom,cpufreq-epss";
			reg = <0 0x18591000 0 0x1000>,
			      <0 0x18592000 0 0x1000>,
			      <0 0x18593000 0 0x1000>;
			reg-names = "freq-domain0", "freq-domain1",
				    "freq-domain2";

			clocks = <&rpmhcc RPMH_CXO_CLK>, <&gcc GPLL0>;
			clock-names = "xo", "alternate";
			interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>;
			interrupt-names = "dcvsh-irq-0", "dcvsh-irq-1", "dcvsh-irq-2";
			#freq-domain-cells = <1>;
		};
	};

	timer {
		compatible = "arm,armv8-timer";
		interrupts = <GIC_PPI 13
				(GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
			     <GIC_PPI 14
				(GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
			     <GIC_PPI 11
				(GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
			     <GIC_PPI 10
				(GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>;
	};

	thermal-zones {
		cpu0-thermal {
			polling-delay-passive = <250>;
			polling-delay = <1000>;

			thermal-sensors = <&tsens0 1>;

			trips {
				cpu0_alert0: trip-point0 {
					temperature = <90000>;
					hysteresis = <2000>;
					type = "passive";
				};

				cpu0_alert1: trip-point1 {
					temperature = <95000>;
					hysteresis = <2000>;
					type = "passive";
				};

				cpu0_crit: cpu_crit {
					temperature = <110000>;
					hysteresis = <1000>;
					type = "critical";
				};
			};

			cooling-maps {
				map0 {
					trip = <&cpu0_alert0>;
					cooling-device = <&CPU0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
							 <&CPU1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
							 <&CPU2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
							 <&CPU3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
				};
				map1 {
					trip = <&cpu0_alert1>;
					cooling-device = <&CPU0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
							 <&CPU1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
							 <&CPU2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
							 <&CPU3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
				};
			};
		};

		cpu1-thermal {
			polling-delay-passive = <250>;
			polling-delay = <1000>;

			thermal-sensors = <&tsens0 2>;

			trips {
				cpu1_alert0: trip-point0 {
					temperature = <90000>;
					hysteresis = <2000>;
					type = "passive";
				};

				cpu1_alert1: trip-point1 {
					temperature = <95000>;
					hysteresis = <2000>;
					type = "passive";
				};

				cpu1_crit: cpu_crit {
					temperature = <110000>;
					hysteresis = <1000>;
					type = "critical";
				};
			};

			cooling-maps {
				map0 {
					trip = <&cpu1_alert0>;
					cooling-device = <&CPU0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
							 <&CPU1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
							 <&CPU2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
							 <&CPU3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
				};
				map1 {
					trip = <&cpu1_alert1>;
					cooling-device = <&CPU0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
							 <&CPU1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
							 <&CPU2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
							 <&CPU3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
				};
			};
		};

		cpu2-thermal {
			polling-delay-passive = <250>;
			polling-delay = <1000>;

			thermal-sensors = <&tsens0 3>;

			trips {
				cpu2_alert0: trip-point0 {
					temperature = <90000>;
					hysteresis = <2000>;
					type = "passive";
				};

				cpu2_alert1: trip-point1 {
					temperature = <95000>;
					hysteresis = <2000>;
					type = "passive";
				};

				cpu2_crit: cpu_crit {
					temperature = <110000>;
					hysteresis = <1000>;
					type = "critical";
				};
			};

			cooling-maps {
				map0 {
					trip = <&cpu2_alert0>;
					cooling-device = <&CPU0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
							 <&CPU1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
							 <&CPU2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
							 <&CPU3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
				};
				map1 {
					trip = <&cpu2_alert1>;
					cooling-device = <&CPU0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
							 <&CPU1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
							 <&CPU2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
							 <&CPU3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
				};
			};
		};

		cpu3-thermal {
			polling-delay-passive = <250>;
			polling-delay = <1000>;

			thermal-sensors = <&tsens0 4>;

			trips {
				cpu3_alert0: trip-point0 {
					temperature = <90000>;
					hysteresis = <2000>;
					type = "passive";
				};

				cpu3_alert1: trip-point1 {
					temperature = <95000>;
					hysteresis = <2000>;
					type = "passive";
				};

				cpu3_crit: cpu_crit {
					temperature = <110000>;
					hysteresis = <1000>;
					type = "critical";
				};
			};

			cooling-maps {
				map0 {
					trip = <&cpu3_alert0>;
					cooling-device = <&CPU0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
							 <&CPU1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
							 <&CPU2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
							 <&CPU3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
				};
				map1 {
					trip = <&cpu3_alert1>;
					cooling-device = <&CPU0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
							 <&CPU1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
							 <&CPU2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
							 <&CPU3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
				};
			};
		};

		cpu4-top-thermal {
			polling-delay-passive = <250>;
			polling-delay = <1000>;

			thermal-sensors = <&tsens0 7>;

			trips {
				cpu4_top_alert0: trip-point0 {
					temperature = <90000>;
					hysteresis = <2000>;
					type = "passive";
				};

				cpu4_top_alert1: trip-point1 {
					temperature = <95000>;
					hysteresis = <2000>;
					type = "passive";
				};

				cpu4_top_crit: cpu_crit {
					temperature = <110000>;
					hysteresis = <1000>;
					type = "critical";
				};
			};

			cooling-maps {
				map0 {
					trip = <&cpu4_top_alert0>;
					cooling-device = <&CPU4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
							 <&CPU5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
							 <&CPU6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
							 <&CPU7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
				};
				map1 {
					trip = <&cpu4_top_alert1>;
					cooling-device = <&CPU4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
							 <&CPU5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
							 <&CPU6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
							 <&CPU7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
				};
			};
		};

		cpu5-top-thermal {
			polling-delay-passive = <250>;
			polling-delay = <1000>;

			thermal-sensors = <&tsens0 8>;

			trips {
				cpu5_top_alert0: trip-point0 {
					temperature = <90000>;
					hysteresis = <2000>;
					type = "passive";
				};

				cpu5_top_alert1: trip-point1 {
					temperature = <95000>;
					hysteresis = <2000>;
					type = "passive";
				};

				cpu5_top_crit: cpu_crit {
					temperature = <110000>;
					hysteresis = <1000>;
					type = "critical";
				};
			};

			cooling-maps {
				map0 {
					trip = <&cpu5_top_alert0>;
					cooling-device = <&CPU4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
							 <&CPU5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
							 <&CPU6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
							 <&CPU7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
				};
				map1 {
					trip = <&cpu5_top_alert1>;
					cooling-device = <&CPU4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
							 <&CPU5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
							 <&CPU6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
							 <&CPU7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
				};
			};
		};

		cpu6-top-thermal {
			polling-delay-passive = <250>;
			polling-delay = <1000>;

			thermal-sensors = <&tsens0 9>;

			trips {
				cpu6_top_alert0: trip-point0 {
					temperature = <90000>;
					hysteresis = <2000>;
					type = "passive";
				};

				cpu6_top_alert1: trip-point1 {
					temperature = <95000>;
					hysteresis = <2000>;
					type = "passive";
				};

				cpu6_top_crit: cpu_crit {
					temperature = <110000>;
					hysteresis = <1000>;
					type = "critical";
				};
			};

			cooling-maps {
				map0 {
					trip = <&cpu6_top_alert0>;
					cooling-device = <&CPU4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
							 <&CPU5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
							 <&CPU6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
							 <&CPU7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
				};
				map1 {
					trip = <&cpu6_top_alert1>;
					cooling-device = <&CPU4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
							 <&CPU5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
							 <&CPU6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
							 <&CPU7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
				};
			};
		};

		cpu7-top-thermal {
			polling-delay-passive = <250>;
			polling-delay = <1000>;

			thermal-sensors = <&tsens0 10>;

			trips {
				cpu7_top_alert0: trip-point0 {
					temperature = <90000>;
					hysteresis = <2000>;
					type = "passive";
				};

				cpu7_top_alert1: trip-point1 {
					temperature = <95000>;
					hysteresis = <2000>;
					type = "passive";
				};

				cpu7_top_crit: cpu_crit {
					temperature = <110000>;
					hysteresis = <1000>;
					type = "critical";
				};
			};

			cooling-maps {
				map0 {
					trip = <&cpu7_top_alert0>;
					cooling-device = <&CPU4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
							 <&CPU5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
							 <&CPU6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
							 <&CPU7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
				};
				map1 {
					trip = <&cpu7_top_alert1>;
					cooling-device = <&CPU4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
							 <&CPU5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
							 <&CPU6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
							 <&CPU7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
				};
			};
		};

		cpu4-bottom-thermal {
			polling-delay-passive = <250>;
			polling-delay = <1000>;

			thermal-sensors = <&tsens0 11>;

			trips {
				cpu4_bottom_alert0: trip-point0 {
					temperature = <90000>;
					hysteresis = <2000>;
					type = "passive";
				};

				cpu4_bottom_alert1: trip-point1 {
					temperature = <95000>;
					hysteresis = <2000>;
					type = "passive";
				};

				cpu4_bottom_crit: cpu_crit {
					temperature = <110000>;
					hysteresis = <1000>;
					type = "critical";
				};
			};

			cooling-maps {
				map0 {
					trip = <&cpu4_bottom_alert0>;
					cooling-device = <&CPU4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
							 <&CPU5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
							 <&CPU6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
							 <&CPU7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
				};
				map1 {
					trip = <&cpu4_bottom_alert1>;
					cooling-device = <&CPU4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
							 <&CPU5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
							 <&CPU6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
							 <&CPU7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
				};
			};
		};

		cpu5-bottom-thermal {
			polling-delay-passive = <250>;
			polling-delay = <1000>;

			thermal-sensors = <&tsens0 12>;

			trips {
				cpu5_bottom_alert0: trip-point0 {
					temperature = <90000>;
					hysteresis = <2000>;
					type = "passive";
				};

				cpu5_bottom_alert1: trip-point1 {
					temperature = <95000>;
					hysteresis = <2000>;
					type = "passive";
				};

				cpu5_bottom_crit: cpu_crit {
					temperature = <110000>;
					hysteresis = <1000>;
					type = "critical";
				};
			};

			cooling-maps {
				map0 {
					trip = <&cpu5_bottom_alert0>;
					cooling-device = <&CPU4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
							 <&CPU5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
							 <&CPU6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
							 <&CPU7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
				};
				map1 {
					trip = <&cpu5_bottom_alert1>;
					cooling-device = <&CPU4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
							 <&CPU5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
							 <&CPU6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
							 <&CPU7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
				};
			};
		};

		cpu6-bottom-thermal {
			polling-delay-passive = <250>;
			polling-delay = <1000>;

			thermal-sensors = <&tsens0 13>;

			trips {
				cpu6_bottom_alert0: trip-point0 {
					temperature = <90000>;
					hysteresis = <2000>;
					type = "passive";
				};

				cpu6_bottom_alert1: trip-point1 {
					temperature = <95000>;
					hysteresis = <2000>;
					type = "passive";
				};

				cpu6_bottom_crit: cpu_crit {
					temperature = <110000>;
					hysteresis = <1000>;
					type = "critical";
				};
			};

			cooling-maps {
				map0 {
					trip = <&cpu6_bottom_alert0>;
					cooling-device = <&CPU4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
							 <&CPU5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
							 <&CPU6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
							 <&CPU7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
				};
				map1 {
					trip = <&cpu6_bottom_alert1>;
					cooling-device = <&CPU4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
							 <&CPU5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
							 <&CPU6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
							 <&CPU7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
				};
			};
		};

		cpu7-bottom-thermal {
			polling-delay-passive = <250>;
			polling-delay = <1000>;

			thermal-sensors = <&tsens0 14>;

			trips {
				cpu7_bottom_alert0: trip-point0 {
					temperature = <90000>;
					hysteresis = <2000>;
					type = "passive";
				};

				cpu7_bottom_alert1: trip-point1 {
					temperature = <95000>;
					hysteresis = <2000>;
					type = "passive";
				};

				cpu7_bottom_crit: cpu_crit {
					temperature = <110000>;
					hysteresis = <1000>;
					type = "critical";
				};
			};

			cooling-maps {
				map0 {
					trip = <&cpu7_bottom_alert0>;
					cooling-device = <&CPU4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
							 <&CPU5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
							 <&CPU6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
							 <&CPU7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
				};
				map1 {
					trip = <&cpu7_bottom_alert1>;
					cooling-device = <&CPU4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
							 <&CPU5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
							 <&CPU6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
							 <&CPU7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
				};
			};
		};

		aoss0-thermal {
			polling-delay-passive = <250>;
			polling-delay = <1000>;

			thermal-sensors = <&tsens0 0>;

			trips {
				aoss0_alert0: trip-point0 {
					temperature = <90000>;
					hysteresis = <2000>;
					type = "hot";
				};
			};
		};

		cluster0-thermal {
			polling-delay-passive = <250>;
			polling-delay = <1000>;

			thermal-sensors = <&tsens0 5>;

			trips {
				cluster0_alert0: trip-point0 {
					temperature = <90000>;
					hysteresis = <2000>;
					type = "hot";
				};
				cluster0_crit: cluster0_crit {
					temperature = <110000>;
					hysteresis = <2000>;
					type = "critical";
				};
			};
		};

		cluster1-thermal {
			polling-delay-passive = <250>;
			polling-delay = <1000>;

			thermal-sensors = <&tsens0 6>;

			trips {
				cluster1_alert0: trip-point0 {
					temperature = <90000>;
					hysteresis = <2000>;
					type = "hot";
				};
				cluster1_crit: cluster1_crit {
					temperature = <110000>;
					hysteresis = <2000>;
					type = "critical";
				};
			};
		};

		gpu-top-thermal {
			polling-delay-passive = <250>;
			polling-delay = <1000>;

			thermal-sensors = <&tsens0 15>;

			trips {
				gpu1_alert0: trip-point0 {
					temperature = <90000>;
					hysteresis = <2000>;
					type = "hot";
				};
			};
		};

		aoss1-thermal {
			polling-delay-passive = <250>;
			polling-delay = <1000>;

			thermal-sensors = <&tsens1 0>;

			trips {
				aoss1_alert0: trip-point0 {
					temperature = <90000>;
					hysteresis = <2000>;
					type = "hot";
				};
			};
		};

		wlan-thermal {
			polling-delay-passive = <250>;
			polling-delay = <1000>;

			thermal-sensors = <&tsens1 1>;

			trips {
				wlan_alert0: trip-point0 {
					temperature = <90000>;
					hysteresis = <2000>;
					type = "hot";
				};
			};
		};

		video-thermal {
			polling-delay-passive = <250>;
			polling-delay = <1000>;

			thermal-sensors = <&tsens1 2>;

			trips {
				video_alert0: trip-point0 {
					temperature = <90000>;
					hysteresis = <2000>;
					type = "hot";
				};
			};
		};

		mem-thermal {
			polling-delay-passive = <250>;
			polling-delay = <1000>;

			thermal-sensors = <&tsens1 3>;

			trips {
				mem_alert0: trip-point0 {
					temperature = <90000>;
					hysteresis = <2000>;
					type = "hot";
				};
			};
		};

		q6-hvx-thermal {
			polling-delay-passive = <250>;
			polling-delay = <1000>;

			thermal-sensors = <&tsens1 4>;

			trips {
				q6_hvx_alert0: trip-point0 {
					temperature = <90000>;
					hysteresis = <2000>;
					type = "hot";
				};
			};
		};

		camera-thermal {
			polling-delay-passive = <250>;
			polling-delay = <1000>;

			thermal-sensors = <&tsens1 5>;

			trips {
				camera_alert0: trip-point0 {
					temperature = <90000>;
					hysteresis = <2000>;
					type = "hot";
				};
			};
		};

		compute-thermal {
			polling-delay-passive = <250>;
			polling-delay = <1000>;

			thermal-sensors = <&tsens1 6>;

			trips {
				compute_alert0: trip-point0 {
					temperature = <90000>;
					hysteresis = <2000>;
					type = "hot";
				};
			};
		};

		npu-thermal {
			polling-delay-passive = <250>;
			polling-delay = <1000>;

			thermal-sensors = <&tsens1 7>;

			trips {
				npu_alert0: trip-point0 {
					temperature = <90000>;
					hysteresis = <2000>;
					type = "hot";
				};
			};
		};

		gpu-bottom-thermal {
			polling-delay-passive = <250>;
			polling-delay = <1000>;

			thermal-sensors = <&tsens1 8>;

			trips {
				gpu2_alert0: trip-point0 {
					temperature = <90000>;
					hysteresis = <2000>;
					type = "hot";
				};
			};
		};
	};
};