1// SPDX-License-Identifier: BSD-3-Clause 2/* 3 * Copyright (c) 2021, Konrad Dybcio <konrad.dybcio@somainline.org> 4 */ 5 6#include <dt-bindings/input/input.h> 7#include <dt-bindings/pinctrl/qcom,pmic-gpio.h> 8#include <dt-bindings/regulator/qcom,rpmh-regulator.h> 9#include "sdm845.dtsi" 10#include "pm8005.dtsi" 11#include "pm8998.dtsi" 12#include "pmi8998.dtsi" 13 14/ { 15 qcom,msm-id = <321 0x20001>; /* SDM845 v2.1 */ 16 qcom,board-id = <8 0>; 17 18 gpio-keys { 19 compatible = "gpio-keys"; 20 21 pinctrl-0 = <&focus_n &snapshot_n &vol_down_n &vol_up_n>; 22 pinctrl-names = "default"; 23 24 key-camera-focus { 25 label = "Camera Focus"; 26 gpios = <&pm8998_gpios 2 GPIO_ACTIVE_LOW>; 27 linux,code = <KEY_CAMERA_FOCUS>; 28 debounce-interval = <15>; 29 linux,can-disable; 30 wakeup-source; 31 }; 32 33 key-camera-snapshot { 34 label = "Camera Snapshot"; 35 gpios = <&pm8998_gpios 7 GPIO_ACTIVE_LOW>; 36 linux,code = <KEY_CAMERA>; 37 debounce-interval = <15>; 38 linux,can-disable; 39 wakeup-source; 40 }; 41 42 key-volume-down { 43 label = "Volume Down"; 44 gpios = <&pm8998_gpios 5 GPIO_ACTIVE_LOW>; 45 linux,code = <KEY_VOLUMEDOWN>; 46 debounce-interval = <15>; 47 linux,can-disable; 48 wakeup-source; 49 }; 50 51 key-volume-up { 52 label = "Volume Up"; 53 gpios = <&pm8998_gpios 6 GPIO_ACTIVE_LOW>; 54 linux,code = <KEY_VOLUMEUP>; 55 debounce-interval = <15>; 56 linux,can-disable; 57 wakeup-source; 58 }; 59 }; 60 61 vph_pwr: vph-pwr-regulator { 62 compatible = "regulator-fixed"; 63 regulator-name = "vph_pwr"; 64 regulator-min-microvolt = <3700000>; 65 regulator-max-microvolt = <3700000>; 66 }; 67 68 vreg_s4a_1p8: pm8998-smps4 { 69 compatible = "regulator-fixed"; 70 regulator-name = "vreg_s4a_1p8"; 71 72 regulator-min-microvolt = <1800000>; 73 regulator-max-microvolt = <1800000>; 74 75 regulator-always-on; 76 regulator-boot-on; 77 78 vin-supply = <&vph_pwr>; 79 }; 80 81 reserved-memory { 82 /* SONY was cool and didn't diverge from MTP this time, yay! */ 83 cont_splash_mem: memory@9d400000 { 84 reg = <0x0 0x9d400000 0x0 0x2400000>; 85 no-map; 86 }; 87 88 ramoops@ffc00000 { 89 compatible = "ramoops"; 90 reg = <0x0 0xffc00000 0x0 0x100000>; 91 record-size = <0x10000>; 92 console-size = <0x60000>; 93 ftrace-size = <0x10000>; 94 pmsg-size = <0x20000>; 95 ecc-size = <16>; 96 no-map; 97 }; 98 }; 99}; 100 101&adsp_pas { 102 firmware-name = "qcom/sdm845/Sony/tama/adsp.mbn"; 103 status = "okay"; 104}; 105 106&apps_rsc { 107 regulators-0 { 108 compatible = "qcom,pm8998-rpmh-regulators"; 109 qcom,pmic-id = "a"; 110 111 vdd-s1-supply = <&vph_pwr>; 112 vdd-s2-supply = <&vph_pwr>; 113 vdd-s3-supply = <&vph_pwr>; 114 vdd-s4-supply = <&vph_pwr>; 115 vdd-s5-supply = <&vph_pwr>; 116 vdd-s6-supply = <&vph_pwr>; 117 vdd-s7-supply = <&vph_pwr>; 118 vdd-s8-supply = <&vph_pwr>; 119 vdd-s9-supply = <&vph_pwr>; 120 vdd-s10-supply = <&vph_pwr>; 121 vdd-s11-supply = <&vph_pwr>; 122 vdd-s12-supply = <&vph_pwr>; 123 vdd-s13-supply = <&vph_pwr>; 124 vdd-l1-l27-supply = <&vreg_s7a_0p9>; 125 vdd-l2-l8-l17-supply = <&vreg_s3a_1p3>; 126 vdd-l3-l11-supply = <&vreg_s7a_0p9>; 127 vdd-l4-l5-supply = <&vreg_s7a_0p9>; 128 vdd-l6-supply = <&vph_pwr>; 129 vdd-l7-l12-l14-l15-supply = <&vreg_s5a_1p9>; 130 vdd-l9-supply = <&vreg_s5a_1p9>; 131 vdd-l10-l23-l25-supply = <&src_vreg_bob>; 132 vdd-l13-l19-l21-supply = <&src_vreg_bob>; 133 vdd-l16-l28-supply = <&src_vreg_bob>; 134 vdd-l18-l22-supply = <&src_vreg_bob>; 135 vdd-l20-l24-supply = <&src_vreg_bob>; 136 vdd-l26-supply = <&vreg_s3a_1p3>; 137 vin-lvs-1-2-supply = <&vreg_s4a_1p8>; 138 139 vreg_s2a_1p1: smps2 { 140 regulator-min-microvolt = <1100000>; 141 regulator-max-microvolt = <1100000>; 142 }; 143 144 vreg_s3a_1p3: smps3 { 145 regulator-min-microvolt = <1352000>; 146 regulator-max-microvolt = <1352000>; 147 }; 148 149 vreg_s5a_1p9: smps5 { 150 regulator-min-microvolt = <1904000>; 151 regulator-max-microvolt = <2040000>; 152 }; 153 154 vreg_s7a_0p9: smps7 { 155 regulator-min-microvolt = <900000>; 156 regulator-max-microvolt = <1028000>; 157 }; 158 159 vreg_l1a_0p9: ldo1 { 160 regulator-min-microvolt = <880000>; 161 regulator-max-microvolt = <880000>; 162 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 163 }; 164 165 vreg_l2a_1p2: ldo2 { 166 regulator-min-microvolt = <1200000>; 167 regulator-max-microvolt = <1200000>; 168 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 169 regulator-always-on; 170 }; 171 172 vreg_l3a_1p0: ldo3 { 173 regulator-min-microvolt = <1000000>; 174 regulator-max-microvolt = <1000000>; 175 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 176 }; 177 178 vreg_l5a_0p8: ldo5 { 179 regulator-min-microvolt = <800000>; 180 regulator-max-microvolt = <800000>; 181 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 182 }; 183 184 vreg_l6a_1p8: ldo6 { 185 regulator-min-microvolt = <1856000>; 186 regulator-max-microvolt = <1856000>; 187 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 188 }; 189 190 vreg_l7a_1p8: ldo7 { 191 regulator-min-microvolt = <1800000>; 192 regulator-max-microvolt = <1800000>; 193 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 194 }; 195 196 vreg_l8a_1p2: ldo8 { 197 regulator-min-microvolt = <1200000>; 198 regulator-max-microvolt = <1248000>; 199 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 200 }; 201 202 vreg_l9a_1p7: ldo9 { 203 regulator-min-microvolt = <1704000>; 204 regulator-max-microvolt = <2928000>; 205 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 206 }; 207 208 vreg_l10a_1p7: ldo10 { 209 regulator-min-microvolt = <1704000>; 210 regulator-max-microvolt = <2928000>; 211 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 212 }; 213 214 vreg_l11a_1p0: ldo11 { 215 regulator-min-microvolt = <1000000>; 216 regulator-max-microvolt = <1048000>; 217 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 218 }; 219 220 vreg_l12a_1p8: ldo12 { 221 regulator-min-microvolt = <1800000>; 222 regulator-max-microvolt = <1800000>; 223 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 224 }; 225 226 vreg_l13a_1p8: ldo13 { 227 regulator-min-microvolt = <1800000>; 228 regulator-max-microvolt = <2960000>; 229 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 230 }; 231 232 vreg_l14a_1p8: ldo14 { 233 regulator-min-microvolt = <1800000>; 234 regulator-max-microvolt = <1800000>; 235 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 236 regulator-system-load = <62000>; 237 }; 238 239 vreg_l15a_1p8: ldo15 { 240 regulator-min-microvolt = <1800000>; 241 regulator-max-microvolt = <1800000>; 242 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 243 }; 244 245 vreg_l16a_2p7: ldo16 { 246 regulator-min-microvolt = <2704000>; 247 regulator-max-microvolt = <2704000>; 248 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 249 }; 250 251 vreg_l17a_1p3: ldo17 { 252 regulator-min-microvolt = <1304000>; 253 regulator-max-microvolt = <1304000>; 254 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 255 }; 256 257 vreg_l18a_2p7: ldo18 { 258 regulator-min-microvolt = <2704000>; 259 regulator-max-microvolt = <2960000>; 260 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 261 }; 262 263 vreg_l19a_2p7: ldo19 { 264 regulator-min-microvolt = <2700000>; 265 regulator-max-microvolt = <2700000>; 266 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 267 268 /* 269 * The driver *really* doesn't want this regualtor to exist, 270 * saying that it could not get the current voltage (-ENOTRECOVERABLE) 271 * even though it surely is used on these devices (as a voltage 272 * source for camera autofocus) 273 */ 274 status = "disabled"; 275 }; 276 277 vreg_l20a_2p7: ldo20 { 278 regulator-min-microvolt = <2704000>; 279 regulator-max-microvolt = <2960000>; 280 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 281 }; 282 283 vreg_l21a_2p7: ldo21 { 284 regulator-min-microvolt = <2704000>; 285 regulator-max-microvolt = <2960000>; 286 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 287 }; 288 289 vreg_l22a_2p8: ldo22 { 290 regulator-min-microvolt = <2800000>; 291 regulator-max-microvolt = <2800000>; 292 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 293 }; 294 295 vreg_l23a_3p0: ldo23 { 296 regulator-min-microvolt = <3000000>; 297 regulator-max-microvolt = <3312000>; 298 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 299 }; 300 301 vreg_l24a_3p1: ldo24 { 302 regulator-min-microvolt = <3088000>; 303 regulator-max-microvolt = <3088000>; 304 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 305 }; 306 307 vreg_l25a_3p0: ldo25 { 308 regulator-min-microvolt = <3000000>; 309 regulator-max-microvolt = <3312000>; 310 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 311 }; 312 313 vreg_l26a_1p2: ldo26 { 314 regulator-min-microvolt = <1200000>; 315 regulator-max-microvolt = <1200000>; 316 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 317 }; 318 319 vreg_l28a_2p8: ldo28 { 320 regulator-min-microvolt = <2856000>; 321 regulator-max-microvolt = <3008000>; 322 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 323 regulator-system-load = <100000>; 324 }; 325 326 vreg_lvs1a_1p8: lvs1 { 327 regulator-min-microvolt = <1800000>; 328 regulator-max-microvolt = <1800000>; 329 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 330 }; 331 332 vreg_lvs2a_1p8: lvs2 { 333 regulator-min-microvolt = <1800000>; 334 regulator-max-microvolt = <1800000>; 335 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 336 }; 337 }; 338 339 regulators-1 { 340 compatible = "qcom,pmi8998-rpmh-regulators"; 341 qcom,pmic-id = "b"; 342 343 src_vreg_bob: bob { 344 regulator-min-microvolt = <3312000>; 345 regulator-max-microvolt = <3600000>; 346 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 347 }; 348 }; 349 350 regulators-2 { 351 compatible = "qcom,pm8005-rpmh-regulators"; 352 qcom,pmic-id = "c"; 353 354 vdd-s1-supply = <&vph_pwr>; 355 vdd-s2-supply = <&vph_pwr>; 356 vdd-s3-supply = <&vph_pwr>; 357 vdd-s4-supply = <&vph_pwr>; 358 359 vreg_s3c_0p6: smps3 { 360 regulator-min-microvolt = <600000>; 361 regulator-max-microvolt = <600000>; 362 }; 363 }; 364}; 365 366&cdsp_pas { 367 firmware-name = "qcom/sdm845/Sony/tama/cdsp.mbn"; 368 status = "okay"; 369}; 370 371&dsi0 { 372 vdda-supply = <&vreg_l26a_1p2>; 373 status = "okay"; 374 375 panel: panel@0 { 376 /* The compatible is assigned in device DTs. */ 377 reg = <0>; 378 379 backlight = <&pmi8998_wled>; 380 vddio-supply = <&vreg_l14a_1p8>; 381 vsp-supply = <&lab>; 382 vsn-supply = <&ibb>; 383 panel-reset-gpios = <&tlmm 6 GPIO_ACTIVE_HIGH>; 384 touch-reset-gpios = <&tlmm 99 GPIO_ACTIVE_HIGH>; 385 386 pinctrl-0 = <&sde_dsi_active &sde_te_active_sleep>; 387 pinctrl-1 = <&sde_dsi_sleep &sde_te_active_sleep>; 388 pinctrl-names = "default", "sleep"; 389 390 port { 391 panel_in: endpoint { 392 remote-endpoint = <&dsi0_out>; 393 }; 394 }; 395 }; 396}; 397 398&dsi0_out { 399 remote-endpoint = <&panel_in>; 400 data-lanes = <0 1 2 3>; 401}; 402 403&dsi0_phy { 404 vdds-supply = <&vreg_l1a_0p9>; 405 status = "okay"; 406}; 407 408&gcc { 409 protected-clocks = <GCC_QSPI_CORE_CLK>, 410 <GCC_QSPI_CORE_CLK_SRC>, 411 <GCC_QSPI_CNOC_PERIPH_AHB_CLK>, 412 <GCC_LPASS_Q6_AXI_CLK>, 413 <GCC_LPASS_SWAY_CLK>; 414}; 415 416&gmu { 417 status = "okay"; 418}; 419 420&gpi_dma0 { 421 status = "okay"; 422}; 423 424&gpi_dma1 { 425 status = "okay"; 426}; 427 428&gpu { 429 status = "okay"; 430 431 zap-shader { 432 memory-region = <&gpu_mem>; 433 firmware-name = "qcom/sdm845/Sony/tama/a630_zap.mbn"; 434 }; 435}; 436 437&i2c5 { 438 clock-frequency = <400000>; 439 status = "okay"; 440 441 touchscreen: touchscreen@2c { 442 compatible = "syna,rmi4-i2c"; 443 reg = <0x2c>; 444 445 interrupts-extended = <&tlmm 125 IRQ_TYPE_EDGE_FALLING>; 446 vdd-supply = <&vreg_l14a_1p8>; 447 /* 448 * This is a blatant abuse of OF, but the panel driver *needs* 449 * to probe first, as the power/gpio switching needs to be precisely 450 * timed in order for both the display and touch panel to function properly. 451 */ 452 incell-supply = <&panel>; 453 454 syna,reset-delay-ms = <220>; 455 syna,startup-delay-ms = <1000>; 456 457 pinctrl-0 = <&ts_default>; 458 pinctrl-1 = <&ts_sleep>; 459 pinctrl-names = "default", "sleep"; 460 461 #address-cells = <1>; 462 #size-cells = <0>; 463 464 rmi4-f01@1 { 465 reg = <0x01>; 466 syna,nosleep-mode = <1>; 467 }; 468 469 rmi4-f12@12 { 470 reg = <0x12>; 471 syna,sensor-type = <1>; 472 }; 473 }; 474}; 475 476&i2c10 { 477 status = "okay"; 478 clock-frequency = <400000>; 479 480 /* Qcom SMB1355 @ 8, c */ 481 /* NXP PN547 NFC @ 28 */ 482 /* Renesas IDTP9221 Qi charger @ 61 */ 483}; 484 485&i2c14 { 486 status = "okay"; 487 clock-frequency = <400000>; 488 489 /* SONY ToF sensor @ 52 */ 490 /* AMS TCS3490 RGB+IR color sensor @ 72 */ 491}; 492 493&ibb { 494 qcom,discharge-resistor-kohms = <300>; 495 regulator-min-microvolt = <5500000>; 496 regulator-max-microvolt = <5700000>; 497 regulator-min-microamp = <0>; 498 regulator-max-microamp = <800000>; 499 regulator-over-current-protection; 500 regulator-soft-start; 501 regulator-pull-down; 502}; 503 504&lab { 505 regulator-min-microvolt = <5500000>; 506 regulator-max-microvolt = <5700000>; 507 regulator-min-microamp = <200000>; 508 regulator-max-microamp = <200000>; 509 regulator-over-current-protection; 510 regulator-soft-start; 511 regulator-pull-down; 512}; 513 514&mdss { 515 status = "okay"; 516}; 517 518&pm8998_gpios { 519 focus_n: focus-n-state { 520 pins = "gpio2"; 521 function = PMIC_GPIO_FUNC_NORMAL; 522 power-source = <0>; 523 bias-pull-up; 524 input-enable; 525 }; 526 527 vol_down_n: vol-down-n-state { 528 pins = "gpio5"; 529 function = PMIC_GPIO_FUNC_NORMAL; 530 power-source = <0>; 531 bias-pull-up; 532 input-enable; 533 }; 534 535 vol_up_n: vol-up-n-state { 536 pins = "gpio6"; 537 function = PMIC_GPIO_FUNC_NORMAL; 538 power-source = <0>; 539 bias-pull-up; 540 input-enable; 541 }; 542 543 snapshot_n: snapshot-n-state { 544 pins = "gpio7"; 545 function = PMIC_GPIO_FUNC_NORMAL; 546 power-source = <0>; 547 bias-pull-up; 548 input-enable; 549 }; 550}; 551 552&pmi8998_wled { 553 default-brightness = <800>; 554 qcom,switching-freq = <800>; 555 qcom,ovp-millivolt = <29600>; 556 qcom,current-boost-limit = <970>; 557 qcom,current-limit-microamp = <20000>; 558 qcom,enabled-strings = <0 1 2 3>; 559 status = "okay"; 560}; 561 562&qupv3_id_0 { 563 status = "okay"; 564}; 565 566&qupv3_id_1 { 567 status = "okay"; 568}; 569 570&sdhc_2 { 571 status = "okay"; 572 573 vmmc-supply = <&vreg_l21a_2p7>; 574 vqmmc-supply = <&vreg_l13a_1p8>; 575 cd-gpios = <&tlmm 126 GPIO_ACTIVE_HIGH>; 576 pinctrl-0 = <&sdc2_default_state>; 577 pinctrl-names = "default"; 578 bus-width = <4>; 579 no-sdio; 580 no-mmc; 581}; 582 583&tlmm { 584 gpio-reserved-ranges = <0 4>, <81 4>; 585 586 sdc2_default_state: sdc2-default-state { 587 clk-pins { 588 pins = "sdc2_clk"; 589 drive-strength = <16>; 590 bias-disable; 591 }; 592 593 cmd-pins { 594 pins = "sdc2_cmd"; 595 drive-strength = <10>; 596 bias-pull-up; 597 }; 598 599 data-pins { 600 pins = "sdc2_data"; 601 drive-strength = <10>; 602 bias-pull-up; 603 }; 604 }; 605 606 sde_dsi_active: sde-dsi-active-state { 607 pins = "gpio6"; 608 function = "gpio"; 609 drive-strength = <8>; 610 bias-disable; 611 }; 612 613 sde_dsi_sleep: sde-dsi-sleep-state { 614 pins = "gpio6"; 615 function = "gpio"; 616 drive-strength = <2>; 617 bias-pull-down; 618 }; 619 620 sde_te_active_sleep: sde-te-active-sleep-state { 621 pins = "gpio10"; 622 function = "mdp_vsync"; 623 drive-strength = <2>; 624 bias-pull-down; 625 }; 626 627 ts_default: ts-default-state { 628 reset-pins { 629 pins = "gpio99"; 630 function = "gpio"; 631 drive-strength = <2>; 632 bias-pull-up; 633 }; 634 635 int-pins { 636 pins = "gpio125"; 637 function = "gpio"; 638 drive-strength = <2>; 639 bias-pull-up; 640 }; 641 }; 642 643 ts_sleep: ts-sleep-state { 644 reset-pins { 645 pins = "gpio99"; 646 function = "gpio"; 647 drive-strength = <2>; 648 bias-pull-down; 649 }; 650 651 int-pins { 652 pins = "gpio125"; 653 function = "gpio"; 654 drive-strength = <2>; 655 bias-pull-down; 656 }; 657 }; 658}; 659 660&uart6 { 661 status = "okay"; 662}; 663 664&uart9 { 665 status = "okay"; 666}; 667 668/* BIG WARNING! DO NOT TOUCH UFS, YOUR DEVICE WILL DIE! */ 669&ufs_mem_hc { status = "disabled"; }; 670&ufs_mem_phy { status = "disabled"; }; 671 672&usb_1 { 673 status = "okay"; 674 675 qcom,select-utmi-as-pipe-clk; 676}; 677 678&usb_1_dwc3 { 679 dr_mode = "peripheral"; 680 681 maximum-speed = "high-speed"; 682 phys = <&usb_1_hsphy>; 683 phy-names = "usb2-phy"; 684}; 685 686&usb_1_hsphy { 687 status = "okay"; 688 689 vdd-supply = <&vreg_l1a_0p9>; 690 vdda-pll-supply = <&vreg_l12a_1p8>; 691 vdda-phy-dpdm-supply = <&vreg_l24a_3p1>; 692}; 693 694&venus { 695 firmware-name = "qcom/sdm845/Sony/tama/venus.mbn"; 696 status = "okay"; 697}; 698