1// SPDX-License-Identifier: GPL-2.0 2/* 3 * Copyright (c) 2019, Linaro Ltd. 4 */ 5 6/dts-v1/; 7 8#include <dt-bindings/gpio/gpio.h> 9#include <dt-bindings/pinctrl/qcom,pmic-gpio.h> 10#include <dt-bindings/regulator/qcom,rpmh-regulator.h> 11#include <dt-bindings/sound/qcom,q6afe.h> 12#include <dt-bindings/sound/qcom,q6asm.h> 13#include "sdm845.dtsi" 14#include "pm8998.dtsi" 15#include "pmi8998.dtsi" 16 17/ { 18 model = "Thundercomm Dragonboard 845c"; 19 compatible = "thundercomm,db845c", "qcom,sdm845"; 20 21 aliases { 22 serial0 = &uart9; 23 hsuart0 = &uart6; 24 }; 25 26 chosen { 27 stdout-path = "serial0:115200n8"; 28 }; 29 30 dc12v: dc12v-regulator { 31 compatible = "regulator-fixed"; 32 regulator-name = "DC12V"; 33 regulator-min-microvolt = <12000000>; 34 regulator-max-microvolt = <12000000>; 35 regulator-always-on; 36 }; 37 38 gpio_keys { 39 compatible = "gpio-keys"; 40 autorepeat; 41 42 pinctrl-names = "default"; 43 pinctrl-0 = <&vol_up_pin_a>; 44 45 vol-up { 46 label = "Volume Up"; 47 linux,code = <KEY_VOLUMEUP>; 48 gpios = <&pm8998_gpio 6 GPIO_ACTIVE_LOW>; 49 }; 50 }; 51 52 leds { 53 compatible = "gpio-leds"; 54 55 user4 { 56 label = "green:user4"; 57 gpios = <&pm8998_gpio 13 GPIO_ACTIVE_HIGH>; 58 linux,default-trigger = "panic-indicator"; 59 default-state = "off"; 60 }; 61 62 wlan { 63 label = "yellow:wlan"; 64 gpios = <&pm8998_gpio 9 GPIO_ACTIVE_HIGH>; 65 linux,default-trigger = "phy0tx"; 66 default-state = "off"; 67 }; 68 69 bt { 70 label = "blue:bt"; 71 gpios = <&pm8998_gpio 5 GPIO_ACTIVE_HIGH>; 72 linux,default-trigger = "bluetooth-power"; 73 default-state = "off"; 74 }; 75 }; 76 77 hdmi-out { 78 compatible = "hdmi-connector"; 79 type = "a"; 80 81 port { 82 hdmi_con: endpoint { 83 remote-endpoint = <<9611_out>; 84 }; 85 }; 86 }; 87 88 lt9611_1v8: lt9611-vdd18-regulator { 89 compatible = "regulator-fixed"; 90 regulator-name = "LT9611_1V8"; 91 92 vin-supply = <&vdc_5v>; 93 regulator-min-microvolt = <1800000>; 94 regulator-max-microvolt = <1800000>; 95 96 gpio = <&tlmm 89 GPIO_ACTIVE_HIGH>; 97 enable-active-high; 98 }; 99 100 lt9611_3v3: lt9611-3v3 { 101 compatible = "regulator-fixed"; 102 regulator-name = "LT9611_3V3"; 103 104 vin-supply = <&vdc_3v3>; 105 regulator-min-microvolt = <3300000>; 106 regulator-max-microvolt = <3300000>; 107 108 // TODO: make it possible to drive same GPIO from two clients 109 // gpio = <&tlmm 89 GPIO_ACTIVE_HIGH>; 110 // enable-active-high; 111 }; 112 113 pcie0_1p05v: pcie-0-1p05v-regulator { 114 compatible = "regulator-fixed"; 115 regulator-name = "PCIE0_1.05V"; 116 117 vin-supply = <&vbat>; 118 regulator-min-microvolt = <1050000>; 119 regulator-max-microvolt = <1050000>; 120 121 // TODO: make it possible to drive same GPIO from two clients 122 // gpio = <&tlmm 90 GPIO_ACTIVE_HIGH>; 123 // enable-active-high; 124 }; 125 126 cam0_dvdd_1v2: reg_cam0_dvdd_1v2 { 127 compatible = "regulator-fixed"; 128 regulator-name = "CAM0_DVDD_1V2"; 129 regulator-min-microvolt = <1200000>; 130 regulator-max-microvolt = <1200000>; 131 enable-active-high; 132 gpio = <&pm8998_gpio 12 GPIO_ACTIVE_HIGH>; 133 pinctrl-names = "default"; 134 pinctrl-0 = <&cam0_dvdd_1v2_en_default>; 135 vin-supply = <&vbat>; 136 }; 137 138 cam0_avdd_2v8: reg_cam0_avdd_2v8 { 139 compatible = "regulator-fixed"; 140 regulator-name = "CAM0_AVDD_2V8"; 141 regulator-min-microvolt = <2800000>; 142 regulator-max-microvolt = <2800000>; 143 enable-active-high; 144 gpio = <&pm8998_gpio 10 GPIO_ACTIVE_HIGH>; 145 pinctrl-names = "default"; 146 pinctrl-0 = <&cam0_avdd_2v8_en_default>; 147 vin-supply = <&vbat>; 148 }; 149 150 /* This regulator is enabled when the VREG_LVS1A_1P8 trace is enabled */ 151 cam3_avdd_2v8: reg_cam3_avdd_2v8 { 152 compatible = "regulator-fixed"; 153 regulator-name = "CAM3_AVDD_2V8"; 154 regulator-min-microvolt = <2800000>; 155 regulator-max-microvolt = <2800000>; 156 regulator-always-on; 157 vin-supply = <&vbat>; 158 }; 159 160 pcie0_3p3v_dual: vldo-3v3-regulator { 161 compatible = "regulator-fixed"; 162 regulator-name = "VLDO_3V3"; 163 164 vin-supply = <&vbat>; 165 regulator-min-microvolt = <3300000>; 166 regulator-max-microvolt = <3300000>; 167 168 gpio = <&tlmm 90 GPIO_ACTIVE_HIGH>; 169 enable-active-high; 170 171 pinctrl-names = "default"; 172 pinctrl-0 = <&pcie0_pwren_state>; 173 }; 174 175 v5p0_hdmiout: v5p0-hdmiout-regulator { 176 compatible = "regulator-fixed"; 177 regulator-name = "V5P0_HDMIOUT"; 178 179 vin-supply = <&vdc_5v>; 180 regulator-min-microvolt = <500000>; 181 regulator-max-microvolt = <500000>; 182 183 // TODO: make it possible to drive same GPIO from two clients 184 // gpio = <&tlmm 89 GPIO_ACTIVE_HIGH>; 185 // enable-active-high; 186 }; 187 188 vbat: vbat-regulator { 189 compatible = "regulator-fixed"; 190 regulator-name = "VBAT"; 191 192 vin-supply = <&dc12v>; 193 regulator-min-microvolt = <4200000>; 194 regulator-max-microvolt = <4200000>; 195 regulator-always-on; 196 }; 197 198 vbat_som: vbat-som-regulator { 199 compatible = "regulator-fixed"; 200 regulator-name = "VBAT_SOM"; 201 202 vin-supply = <&dc12v>; 203 regulator-min-microvolt = <4200000>; 204 regulator-max-microvolt = <4200000>; 205 regulator-always-on; 206 }; 207 208 vdc_3v3: vdc-3v3-regulator { 209 compatible = "regulator-fixed"; 210 regulator-name = "VDC_3V3"; 211 vin-supply = <&dc12v>; 212 regulator-min-microvolt = <3300000>; 213 regulator-max-microvolt = <3300000>; 214 regulator-always-on; 215 }; 216 217 vdc_5v: vdc-5v-regulator { 218 compatible = "regulator-fixed"; 219 regulator-name = "VDC_5V"; 220 221 vin-supply = <&dc12v>; 222 regulator-min-microvolt = <500000>; 223 regulator-max-microvolt = <500000>; 224 regulator-always-on; 225 }; 226 227 vreg_s4a_1p8: vreg-s4a-1p8 { 228 compatible = "regulator-fixed"; 229 regulator-name = "vreg_s4a_1p8"; 230 231 regulator-min-microvolt = <1800000>; 232 regulator-max-microvolt = <1800000>; 233 regulator-always-on; 234 }; 235 236 vph_pwr: vph-pwr-regulator { 237 compatible = "regulator-fixed"; 238 regulator-name = "vph_pwr"; 239 240 vin-supply = <&vbat_som>; 241 }; 242}; 243 244&adsp_pas { 245 status = "okay"; 246 247 firmware-name = "qcom/sdm845/adsp.mdt"; 248}; 249 250&apps_rsc { 251 pm8998-rpmh-regulators { 252 compatible = "qcom,pm8998-rpmh-regulators"; 253 qcom,pmic-id = "a"; 254 vdd-s1-supply = <&vph_pwr>; 255 vdd-s2-supply = <&vph_pwr>; 256 vdd-s3-supply = <&vph_pwr>; 257 vdd-s4-supply = <&vph_pwr>; 258 vdd-s5-supply = <&vph_pwr>; 259 vdd-s6-supply = <&vph_pwr>; 260 vdd-s7-supply = <&vph_pwr>; 261 vdd-s8-supply = <&vph_pwr>; 262 vdd-s9-supply = <&vph_pwr>; 263 vdd-s10-supply = <&vph_pwr>; 264 vdd-s11-supply = <&vph_pwr>; 265 vdd-s12-supply = <&vph_pwr>; 266 vdd-s13-supply = <&vph_pwr>; 267 vdd-l1-l27-supply = <&vreg_s7a_1p025>; 268 vdd-l2-l8-l17-supply = <&vreg_s3a_1p35>; 269 vdd-l3-l11-supply = <&vreg_s7a_1p025>; 270 vdd-l4-l5-supply = <&vreg_s7a_1p025>; 271 vdd-l6-supply = <&vph_pwr>; 272 vdd-l7-l12-l14-l15-supply = <&vreg_s5a_2p04>; 273 vdd-l9-supply = <&vreg_bob>; 274 vdd-l10-l23-l25-supply = <&vreg_bob>; 275 vdd-l13-l19-l21-supply = <&vreg_bob>; 276 vdd-l16-l28-supply = <&vreg_bob>; 277 vdd-l18-l22-supply = <&vreg_bob>; 278 vdd-l20-l24-supply = <&vreg_bob>; 279 vdd-l26-supply = <&vreg_s3a_1p35>; 280 vin-lvs-1-2-supply = <&vreg_s4a_1p8>; 281 282 vreg_s3a_1p35: smps3 { 283 regulator-min-microvolt = <1352000>; 284 regulator-max-microvolt = <1352000>; 285 }; 286 287 vreg_s5a_2p04: smps5 { 288 regulator-min-microvolt = <1904000>; 289 regulator-max-microvolt = <2040000>; 290 }; 291 292 vreg_s7a_1p025: smps7 { 293 regulator-min-microvolt = <900000>; 294 regulator-max-microvolt = <1028000>; 295 }; 296 297 vreg_l1a_0p875: ldo1 { 298 regulator-min-microvolt = <880000>; 299 regulator-max-microvolt = <880000>; 300 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 301 }; 302 303 vreg_l5a_0p8: ldo5 { 304 regulator-min-microvolt = <800000>; 305 regulator-max-microvolt = <800000>; 306 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 307 }; 308 309 vreg_l12a_1p8: ldo12 { 310 regulator-min-microvolt = <1800000>; 311 regulator-max-microvolt = <1800000>; 312 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 313 }; 314 315 vreg_l7a_1p8: ldo7 { 316 regulator-min-microvolt = <1800000>; 317 regulator-max-microvolt = <1800000>; 318 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 319 }; 320 321 vreg_l13a_2p95: ldo13 { 322 regulator-min-microvolt = <1800000>; 323 regulator-max-microvolt = <2960000>; 324 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 325 }; 326 327 vreg_l17a_1p3: ldo17 { 328 regulator-min-microvolt = <1304000>; 329 regulator-max-microvolt = <1304000>; 330 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 331 }; 332 333 vreg_l20a_2p95: ldo20 { 334 regulator-min-microvolt = <2960000>; 335 regulator-max-microvolt = <2968000>; 336 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 337 }; 338 339 vreg_l21a_2p95: ldo21 { 340 regulator-min-microvolt = <2960000>; 341 regulator-max-microvolt = <2968000>; 342 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 343 }; 344 345 vreg_l24a_3p075: ldo24 { 346 regulator-min-microvolt = <3088000>; 347 regulator-max-microvolt = <3088000>; 348 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 349 }; 350 351 vreg_l25a_3p3: ldo25 { 352 regulator-min-microvolt = <3300000>; 353 regulator-max-microvolt = <3312000>; 354 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 355 }; 356 357 vreg_l26a_1p2: ldo26 { 358 regulator-min-microvolt = <1200000>; 359 regulator-max-microvolt = <1200000>; 360 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 361 }; 362 363 vreg_lvs1a_1p8: lvs1 { 364 regulator-min-microvolt = <1800000>; 365 regulator-max-microvolt = <1800000>; 366 regulator-always-on; 367 }; 368 369 vreg_lvs2a_1p8: lvs2 { 370 regulator-min-microvolt = <1800000>; 371 regulator-max-microvolt = <1800000>; 372 regulator-always-on; 373 }; 374 }; 375 376 pmi8998-rpmh-regulators { 377 compatible = "qcom,pmi8998-rpmh-regulators"; 378 qcom,pmic-id = "b"; 379 380 vdd-bob-supply = <&vph_pwr>; 381 382 vreg_bob: bob { 383 regulator-min-microvolt = <3312000>; 384 regulator-max-microvolt = <3600000>; 385 regulator-initial-mode = <RPMH_REGULATOR_MODE_AUTO>; 386 regulator-allow-bypass; 387 }; 388 }; 389}; 390 391&cdsp_pas { 392 status = "okay"; 393 firmware-name = "qcom/sdm845/cdsp.mdt"; 394}; 395 396&dsi0 { 397 status = "okay"; 398 vdda-supply = <&vreg_l26a_1p2>; 399 400 ports { 401 port@1 { 402 endpoint { 403 remote-endpoint = <<9611_a>; 404 data-lanes = <0 1 2 3>; 405 }; 406 }; 407 }; 408}; 409 410&dsi0_phy { 411 status = "okay"; 412 vdds-supply = <&vreg_l1a_0p875>; 413}; 414 415&gcc { 416 protected-clocks = <GCC_QSPI_CORE_CLK>, 417 <GCC_QSPI_CORE_CLK_SRC>, 418 <GCC_QSPI_CNOC_PERIPH_AHB_CLK>, 419 <GCC_LPASS_Q6_AXI_CLK>, 420 <GCC_LPASS_SWAY_CLK>; 421}; 422 423&gpu { 424 zap-shader { 425 memory-region = <&gpu_mem>; 426 firmware-name = "qcom/sdm845/a630_zap.mbn"; 427 }; 428}; 429 430&i2c10 { 431 status = "okay"; 432 clock-frequency = <400000>; 433 434 lt9611_codec: hdmi-bridge@3b { 435 compatible = "lontium,lt9611"; 436 reg = <0x3b>; 437 #sound-dai-cells = <1>; 438 439 interrupts-extended = <&tlmm 84 IRQ_TYPE_EDGE_FALLING>; 440 441 reset-gpios = <&tlmm 128 GPIO_ACTIVE_HIGH>; 442 443 vdd-supply = <<9611_1v8>; 444 vcc-supply = <<9611_3v3>; 445 446 pinctrl-names = "default"; 447 pinctrl-0 = <<9611_irq_pin>, <&dsi_sw_sel>; 448 449 ports { 450 #address-cells = <1>; 451 #size-cells = <0>; 452 453 port@0 { 454 reg = <0>; 455 456 lt9611_a: endpoint { 457 remote-endpoint = <&dsi0_out>; 458 }; 459 }; 460 461 port@2 { 462 reg = <2>; 463 464 lt9611_out: endpoint { 465 remote-endpoint = <&hdmi_con>; 466 }; 467 }; 468 }; 469 }; 470}; 471 472&i2c11 { 473 /* On Low speed expansion */ 474 label = "LS-I2C1"; 475 status = "okay"; 476}; 477 478&i2c14 { 479 /* On Low speed expansion */ 480 label = "LS-I2C0"; 481 status = "okay"; 482}; 483 484&mdss { 485 status = "okay"; 486}; 487 488&mdss_mdp { 489 status = "okay"; 490}; 491 492&mss_pil { 493 status = "okay"; 494 firmware-name = "qcom/sdm845/mba.mbn", "qcom/sdm845/modem.mbn"; 495}; 496 497&pcie0 { 498 status = "okay"; 499 perst-gpio = <&tlmm 35 GPIO_ACTIVE_LOW>; 500 enable-gpio = <&tlmm 134 GPIO_ACTIVE_HIGH>; 501 502 vddpe-3v3-supply = <&pcie0_3p3v_dual>; 503 504 pinctrl-names = "default"; 505 pinctrl-0 = <&pcie0_default_state>; 506}; 507 508&pcie0_phy { 509 status = "okay"; 510 511 vdda-phy-supply = <&vreg_l1a_0p875>; 512 vdda-pll-supply = <&vreg_l26a_1p2>; 513}; 514 515&pcie1 { 516 status = "okay"; 517 perst-gpio = <&tlmm 102 GPIO_ACTIVE_LOW>; 518 519 pinctrl-names = "default"; 520 pinctrl-0 = <&pcie1_default_state>; 521}; 522 523&pcie1_phy { 524 status = "okay"; 525 526 vdda-phy-supply = <&vreg_l1a_0p875>; 527 vdda-pll-supply = <&vreg_l26a_1p2>; 528}; 529 530&pm8998_gpio { 531 gpio-line-names = 532 "NC", 533 "NC", 534 "WLAN_SW_CTRL", 535 "NC", 536 "PM_GPIO5_BLUE_BT_LED", 537 "VOL_UP_N", 538 "NC", 539 "ADC_IN1", 540 "PM_GPIO9_YEL_WIFI_LED", 541 "CAM0_AVDD_EN", 542 "NC", 543 "CAM0_DVDD_EN", 544 "PM_GPIO13_GREEN_U4_LED", 545 "DIV_CLK2", 546 "NC", 547 "NC", 548 "NC", 549 "SMB_STAT", 550 "NC", 551 "NC", 552 "ADC_IN2", 553 "OPTION1", 554 "WCSS_PWR_REQ", 555 "PM845_GPIO24", 556 "OPTION2", 557 "PM845_SLB"; 558 559 cam0_dvdd_1v2_en_default: cam0-dvdd-1v2-en { 560 pins = "gpio12"; 561 function = "normal"; 562 563 bias-pull-up; 564 drive-push-pull; 565 qcom,drive-strength = <PMIC_GPIO_STRENGTH_HIGH>; 566 }; 567 568 cam0_avdd_2v8_en_default: cam0-avdd-2v8-en { 569 pins = "gpio10"; 570 function = "normal"; 571 572 bias-pull-up; 573 drive-push-pull; 574 qcom,drive-strength = <PMIC_GPIO_STRENGTH_HIGH>; 575 }; 576 577 vol_up_pin_a: vol-up-active { 578 pins = "gpio6"; 579 function = "normal"; 580 input-enable; 581 bias-pull-up; 582 qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>; 583 }; 584}; 585 586&pm8998_pon { 587 resin { 588 compatible = "qcom,pm8941-resin"; 589 interrupts = <0x0 0x8 1 IRQ_TYPE_EDGE_BOTH>; 590 debounce = <15625>; 591 bias-pull-up; 592 linux,code = <KEY_VOLUMEDOWN>; 593 }; 594}; 595 596/* QUAT I2S Uses 4 I2S SD Lines for audio on LT9611 HDMI Bridge */ 597&q6afedai { 598 qi2s@22 { 599 reg = <22>; 600 qcom,sd-lines = <0 1 2 3>; 601 }; 602}; 603 604&q6asmdai { 605 dai@0 { 606 reg = <0>; 607 }; 608 609 dai@1 { 610 reg = <1>; 611 }; 612 613 dai@2 { 614 reg = <2>; 615 }; 616 617 dai@3 { 618 reg = <3>; 619 direction = <2>; 620 is-compress-dai; 621 }; 622}; 623 624&qupv3_id_0 { 625 status = "okay"; 626}; 627 628&qupv3_id_1 { 629 status = "okay"; 630}; 631 632&sdhc_2 { 633 status = "okay"; 634 635 pinctrl-names = "default"; 636 pinctrl-0 = <&sdc2_default_state &sdc2_card_det_n>; 637 638 vmmc-supply = <&vreg_l21a_2p95>; 639 vqmmc-supply = <&vreg_l13a_2p95>; 640 641 bus-width = <4>; 642 cd-gpios = <&tlmm 126 GPIO_ACTIVE_LOW>; 643}; 644 645&sound { 646 compatible = "qcom,db845c-sndcard"; 647 pinctrl-0 = <&quat_mi2s_active 648 &quat_mi2s_sd0_active 649 &quat_mi2s_sd1_active 650 &quat_mi2s_sd2_active 651 &quat_mi2s_sd3_active>; 652 pinctrl-names = "default"; 653 model = "DB845c"; 654 audio-routing = 655 "RX_BIAS", "MCLK", 656 "AMIC1", "MIC BIAS1", 657 "AMIC2", "MIC BIAS2", 658 "DMIC0", "MIC BIAS1", 659 "DMIC1", "MIC BIAS1", 660 "DMIC2", "MIC BIAS3", 661 "DMIC3", "MIC BIAS3", 662 "SpkrLeft IN", "SPK1 OUT", 663 "SpkrRight IN", "SPK2 OUT", 664 "MM_DL1", "MultiMedia1 Playback", 665 "MM_DL2", "MultiMedia2 Playback", 666 "MM_DL4", "MultiMedia4 Playback", 667 "MultiMedia3 Capture", "MM_UL3"; 668 669 mm1-dai-link { 670 link-name = "MultiMedia1"; 671 cpu { 672 sound-dai = <&q6asmdai MSM_FRONTEND_DAI_MULTIMEDIA1>; 673 }; 674 }; 675 676 mm2-dai-link { 677 link-name = "MultiMedia2"; 678 cpu { 679 sound-dai = <&q6asmdai MSM_FRONTEND_DAI_MULTIMEDIA2>; 680 }; 681 }; 682 683 mm3-dai-link { 684 link-name = "MultiMedia3"; 685 cpu { 686 sound-dai = <&q6asmdai MSM_FRONTEND_DAI_MULTIMEDIA3>; 687 }; 688 }; 689 690 mm4-dai-link { 691 link-name = "MultiMedia4"; 692 cpu { 693 sound-dai = <&q6asmdai MSM_FRONTEND_DAI_MULTIMEDIA4>; 694 }; 695 }; 696 697 hdmi-dai-link { 698 link-name = "HDMI Playback"; 699 cpu { 700 sound-dai = <&q6afedai QUATERNARY_MI2S_RX>; 701 }; 702 703 platform { 704 sound-dai = <&q6routing>; 705 }; 706 707 codec { 708 sound-dai = <<9611_codec 0>; 709 }; 710 }; 711 712 slim-dai-link { 713 link-name = "SLIM Playback"; 714 cpu { 715 sound-dai = <&q6afedai SLIMBUS_0_RX>; 716 }; 717 718 platform { 719 sound-dai = <&q6routing>; 720 }; 721 722 codec { 723 sound-dai = <&left_spkr>, <&right_spkr>, <&swm 0>, <&wcd9340 0>; 724 }; 725 }; 726 727 slimcap-dai-link { 728 link-name = "SLIM Capture"; 729 cpu { 730 sound-dai = <&q6afedai SLIMBUS_0_TX>; 731 }; 732 733 platform { 734 sound-dai = <&q6routing>; 735 }; 736 737 codec { 738 sound-dai = <&wcd9340 1>; 739 }; 740 }; 741}; 742 743&spi2 { 744 /* On Low speed expansion */ 745 label = "LS-SPI0"; 746 status = "okay"; 747}; 748 749&tlmm { 750 cam0_default: cam0_default { 751 rst { 752 pins = "gpio9"; 753 function = "gpio"; 754 755 drive-strength = <16>; 756 bias-disable; 757 }; 758 759 mclk0 { 760 pins = "gpio13"; 761 function = "cam_mclk"; 762 763 drive-strength = <16>; 764 bias-disable; 765 }; 766 }; 767 768 cam3_default: cam3_default { 769 rst { 770 function = "gpio"; 771 pins = "gpio21"; 772 773 drive-strength = <16>; 774 bias-disable; 775 }; 776 777 mclk3 { 778 function = "cam_mclk"; 779 pins = "gpio16"; 780 781 drive-strength = <16>; 782 bias-disable; 783 }; 784 }; 785 786 dsi_sw_sel: dsi-sw-sel { 787 pins = "gpio120"; 788 function = "gpio"; 789 790 drive-strength = <2>; 791 bias-disable; 792 output-high; 793 }; 794 795 lt9611_irq_pin: lt9611-irq { 796 pins = "gpio84"; 797 function = "gpio"; 798 bias-disable; 799 }; 800 801 pcie0_default_state: pcie0-default { 802 clkreq { 803 pins = "gpio36"; 804 function = "pci_e0"; 805 bias-pull-up; 806 }; 807 808 reset-n { 809 pins = "gpio35"; 810 function = "gpio"; 811 812 drive-strength = <2>; 813 output-low; 814 bias-pull-down; 815 }; 816 817 wake-n { 818 pins = "gpio37"; 819 function = "gpio"; 820 821 drive-strength = <2>; 822 bias-pull-up; 823 }; 824 }; 825 826 pcie0_pwren_state: pcie0-pwren { 827 pins = "gpio90"; 828 function = "gpio"; 829 830 drive-strength = <2>; 831 bias-disable; 832 }; 833 834 pcie1_default_state: pcie1-default { 835 perst-n { 836 pins = "gpio102"; 837 function = "gpio"; 838 839 drive-strength = <16>; 840 bias-disable; 841 }; 842 843 clkreq { 844 pins = "gpio103"; 845 function = "pci_e1"; 846 bias-pull-up; 847 }; 848 849 wake-n { 850 pins = "gpio11"; 851 function = "gpio"; 852 853 drive-strength = <2>; 854 bias-pull-up; 855 }; 856 857 reset-n { 858 pins = "gpio75"; 859 function = "gpio"; 860 861 drive-strength = <16>; 862 bias-pull-up; 863 output-high; 864 }; 865 }; 866 867 sdc2_default_state: sdc2-default { 868 clk { 869 pins = "sdc2_clk"; 870 bias-disable; 871 872 /* 873 * It seems that mmc_test reports errors if drive 874 * strength is not 16 on clk, cmd, and data pins. 875 */ 876 drive-strength = <16>; 877 }; 878 879 cmd { 880 pins = "sdc2_cmd"; 881 bias-pull-up; 882 drive-strength = <10>; 883 }; 884 885 data { 886 pins = "sdc2_data"; 887 bias-pull-up; 888 drive-strength = <10>; 889 }; 890 }; 891 892 sdc2_card_det_n: sd-card-det-n { 893 pins = "gpio126"; 894 function = "gpio"; 895 bias-pull-up; 896 }; 897 898 wcd_intr_default: wcd_intr_default { 899 pins = <54>; 900 function = "gpio"; 901 902 input-enable; 903 bias-pull-down; 904 drive-strength = <2>; 905 }; 906}; 907 908&uart3 { 909 label = "LS-UART0"; 910 status = "disabled"; 911}; 912 913&uart6 { 914 status = "okay"; 915 916 bluetooth { 917 compatible = "qcom,wcn3990-bt"; 918 919 vddio-supply = <&vreg_s4a_1p8>; 920 vddxo-supply = <&vreg_l7a_1p8>; 921 vddrf-supply = <&vreg_l17a_1p3>; 922 vddch0-supply = <&vreg_l25a_3p3>; 923 max-speed = <3200000>; 924 }; 925}; 926 927&uart9 { 928 label = "LS-UART1"; 929 status = "okay"; 930}; 931 932&usb_1 { 933 status = "okay"; 934}; 935 936&usb_1_dwc3 { 937 dr_mode = "peripheral"; 938}; 939 940&usb_1_hsphy { 941 status = "okay"; 942 943 vdd-supply = <&vreg_l1a_0p875>; 944 vdda-pll-supply = <&vreg_l12a_1p8>; 945 vdda-phy-dpdm-supply = <&vreg_l24a_3p075>; 946 947 qcom,imp-res-offset-value = <8>; 948 qcom,hstx-trim-value = <QUSB2_V2_HSTX_TRIM_21_6_MA>; 949 qcom,preemphasis-level = <QUSB2_V2_PREEMPHASIS_5_PERCENT>; 950 qcom,preemphasis-width = <QUSB2_V2_PREEMPHASIS_WIDTH_HALF_BIT>; 951}; 952 953&usb_1_qmpphy { 954 status = "okay"; 955 956 vdda-phy-supply = <&vreg_l26a_1p2>; 957 vdda-pll-supply = <&vreg_l1a_0p875>; 958}; 959 960&usb_2 { 961 status = "okay"; 962}; 963 964&usb_2_dwc3 { 965 dr_mode = "host"; 966}; 967 968&usb_2_hsphy { 969 status = "okay"; 970 971 vdd-supply = <&vreg_l1a_0p875>; 972 vdda-pll-supply = <&vreg_l12a_1p8>; 973 vdda-phy-dpdm-supply = <&vreg_l24a_3p075>; 974 975 qcom,imp-res-offset-value = <8>; 976 qcom,hstx-trim-value = <QUSB2_V2_HSTX_TRIM_22_8_MA>; 977}; 978 979&usb_2_qmpphy { 980 status = "okay"; 981 982 vdda-phy-supply = <&vreg_l26a_1p2>; 983 vdda-pll-supply = <&vreg_l1a_0p875>; 984}; 985 986&ufs_mem_hc { 987 status = "okay"; 988 989 reset-gpios = <&tlmm 150 GPIO_ACTIVE_LOW>; 990 991 vcc-supply = <&vreg_l20a_2p95>; 992 vcc-max-microamp = <800000>; 993}; 994 995&ufs_mem_phy { 996 status = "okay"; 997 998 vdda-phy-supply = <&vreg_l1a_0p875>; 999 vdda-pll-supply = <&vreg_l26a_1p2>; 1000}; 1001 1002&wcd9340{ 1003 pinctrl-0 = <&wcd_intr_default>; 1004 pinctrl-names = "default"; 1005 clock-names = "extclk"; 1006 clocks = <&rpmhcc RPMH_LN_BB_CLK2>; 1007 reset-gpios = <&tlmm 64 0>; 1008 vdd-buck-supply = <&vreg_s4a_1p8>; 1009 vdd-buck-sido-supply = <&vreg_s4a_1p8>; 1010 vdd-tx-supply = <&vreg_s4a_1p8>; 1011 vdd-rx-supply = <&vreg_s4a_1p8>; 1012 vdd-io-supply = <&vreg_s4a_1p8>; 1013 1014 swm: swm@c85 { 1015 left_spkr: wsa8810-left{ 1016 compatible = "sdw10217201000"; 1017 reg = <0 1>; 1018 powerdown-gpios = <&wcdgpio 2 GPIO_ACTIVE_HIGH>; 1019 #thermal-sensor-cells = <0>; 1020 sound-name-prefix = "SpkrLeft"; 1021 #sound-dai-cells = <0>; 1022 }; 1023 1024 right_spkr: wsa8810-right{ 1025 compatible = "sdw10217201000"; 1026 powerdown-gpios = <&wcdgpio 2 GPIO_ACTIVE_HIGH>; 1027 reg = <0 2>; 1028 #thermal-sensor-cells = <0>; 1029 sound-name-prefix = "SpkrRight"; 1030 #sound-dai-cells = <0>; 1031 }; 1032 }; 1033}; 1034 1035&wifi { 1036 status = "okay"; 1037 1038 vdd-0.8-cx-mx-supply = <&vreg_l5a_0p8>; 1039 vdd-1.8-xo-supply = <&vreg_l7a_1p8>; 1040 vdd-1.3-rfa-supply = <&vreg_l17a_1p3>; 1041 vdd-3.3-ch0-supply = <&vreg_l25a_3p3>; 1042 1043 qcom,snoc-host-cap-8bit-quirk; 1044}; 1045 1046/* PINCTRL - additions to nodes defined in sdm845.dtsi */ 1047&qup_spi2_default { 1048 drive-strength = <16>; 1049}; 1050 1051&qup_uart3_default{ 1052 pinmux { 1053 pins = "gpio41", "gpio42", "gpio43", "gpio44"; 1054 function = "qup3"; 1055 }; 1056}; 1057 1058&qup_i2c10_default { 1059 pinconf { 1060 pins = "gpio55", "gpio56"; 1061 drive-strength = <2>; 1062 bias-disable; 1063 }; 1064}; 1065 1066&qup_uart6_default { 1067 pinmux { 1068 pins = "gpio45", "gpio46", "gpio47", "gpio48"; 1069 function = "qup6"; 1070 }; 1071 1072 cts { 1073 pins = "gpio45"; 1074 bias-disable; 1075 }; 1076 1077 rts-tx { 1078 pins = "gpio46", "gpio47"; 1079 drive-strength = <2>; 1080 bias-disable; 1081 }; 1082 1083 rx { 1084 pins = "gpio48"; 1085 bias-pull-up; 1086 }; 1087}; 1088 1089&qup_uart9_default { 1090 pinconf-tx { 1091 pins = "gpio4"; 1092 drive-strength = <2>; 1093 bias-disable; 1094 }; 1095 1096 pinconf-rx { 1097 pins = "gpio5"; 1098 drive-strength = <2>; 1099 bias-pull-up; 1100 }; 1101}; 1102 1103&pm8998_gpio { 1104 1105}; 1106 1107&cci { 1108 status = "okay"; 1109}; 1110 1111&cci_i2c0 { 1112 camera@10 { 1113 compatible = "ovti,ov8856"; 1114 reg = <0x10>; 1115 1116 // CAM0_RST_N 1117 reset-gpios = <&tlmm 9 0>; 1118 pinctrl-names = "default"; 1119 pinctrl-0 = <&cam0_default>; 1120 gpios = <&tlmm 13 0>, 1121 <&tlmm 9 0>; 1122 1123 clocks = <&clock_camcc CAM_CC_MCLK0_CLK>; 1124 clock-names = "xvclk"; 1125 clock-frequency = <19200000>; 1126 1127 /* The &vreg_s4a_1p8 trace is powered on as a, 1128 * so it is represented by a fixed regulator. 1129 * 1130 * The 2.8V vdda-supply and 1.2V vddd-supply regulators 1131 * both have to be enabled through the power management 1132 * gpios. 1133 */ 1134 power-domains = <&clock_camcc TITAN_TOP_GDSC>; 1135 1136 dovdd-supply = <&vreg_lvs1a_1p8>; 1137 avdd-supply = <&cam0_avdd_2v8>; 1138 dvdd-supply = <&cam0_dvdd_1v2>; 1139 1140 status = "disable"; 1141 1142 port { 1143 ov8856_ep: endpoint { 1144 clock-lanes = <1>; 1145 link-frequencies = /bits/ 64 1146 <360000000 180000000>; 1147 data-lanes = <1 2 3 4>; 1148// remote-endpoint = <&csiphy0_ep>; 1149 }; 1150 }; 1151 }; 1152}; 1153 1154&cci_i2c1 { 1155 camera@60 { 1156 compatible = "ovti,ov7251"; 1157 1158 // I2C address as per ov7251.txt linux documentation 1159 reg = <0x60>; 1160 1161 // CAM3_RST_N 1162 enable-gpios = <&tlmm 21 0>; 1163 pinctrl-names = "default"; 1164 pinctrl-0 = <&cam3_default>; 1165 gpios = <&tlmm 16 0>, 1166 <&tlmm 21 0>; 1167 1168 clocks = <&clock_camcc CAM_CC_MCLK3_CLK>; 1169 clock-names = "xclk"; 1170 clock-frequency = <24000000>; 1171 1172 /* The &vreg_s4a_1p8 trace always powered on. 1173 * 1174 * The 2.8V vdda-supply regulator is enabled when the 1175 * vreg_s4a_1p8 trace is pulled high. 1176 * It too is represented by a fixed regulator. 1177 * 1178 * No 1.2V vddd-supply regulator is used. 1179 */ 1180 power-domains = <&clock_camcc TITAN_TOP_GDSC>; 1181 1182 vdddo-supply = <&vreg_lvs1a_1p8>; 1183 vdda-supply = <&cam3_avdd_2v8>; 1184 1185 status = "disable"; 1186 1187 port { 1188 ov7251_ep: endpoint { 1189 clock-lanes = <1>; 1190 data-lanes = <0 1>; 1191// remote-endpoint = <&csiphy3_ep>; 1192 }; 1193 }; 1194 }; 1195}; 1196