1// SPDX-License-Identifier: (GPL-2.0+ OR MIT) 2/* 3 * Google Cheza device tree source (common between revisions) 4 * 5 * Copyright 2018 Google LLC. 6 */ 7 8#include <dt-bindings/gpio/gpio.h> 9#include <dt-bindings/input/input.h> 10#include <dt-bindings/regulator/qcom,rpmh-regulator.h> 11#include "sdm845.dtsi" 12 13/* PMICs depend on spmi_bus label and so must come after SoC */ 14#include "pm8005.dtsi" 15#include "pm8998.dtsi" 16 17/ { 18 aliases { 19 bluetooth0 = &bluetooth; 20 hsuart0 = &uart6; 21 serial0 = &uart9; 22 wifi0 = &wifi; 23 }; 24 25 chosen { 26 stdout-path = "serial0:115200n8"; 27 }; 28 29 backlight: backlight { 30 compatible = "pwm-backlight"; 31 pwms = <&cros_ec_pwm 0>; 32 enable-gpios = <&tlmm 37 GPIO_ACTIVE_HIGH>; 33 power-supply = <&ppvar_sys>; 34 pinctrl-names = "default"; 35 pinctrl-0 = <&ap_edp_bklten>; 36 }; 37 38 /* FIXED REGULATORS - parents above children */ 39 40 /* This is the top level supply and variable voltage */ 41 ppvar_sys: ppvar-sys-regulator { 42 compatible = "regulator-fixed"; 43 regulator-name = "ppvar_sys"; 44 regulator-always-on; 45 regulator-boot-on; 46 }; 47 48 /* This divides ppvar_sys by 2, so voltage is variable */ 49 src_vph_pwr: src-vph-pwr-regulator { 50 compatible = "regulator-fixed"; 51 regulator-name = "src_vph_pwr"; 52 53 /* EC turns on with switchcap_on_l; always on for AP */ 54 regulator-always-on; 55 regulator-boot-on; 56 57 vin-supply = <&ppvar_sys>; 58 }; 59 60 pp5000_a: pp5000-a-regulator { 61 compatible = "regulator-fixed"; 62 regulator-name = "pp5000_a"; 63 64 /* EC turns on with en_pp5000_a; always on for AP */ 65 regulator-always-on; 66 regulator-boot-on; 67 regulator-min-microvolt = <5000000>; 68 regulator-max-microvolt = <5000000>; 69 70 vin-supply = <&ppvar_sys>; 71 }; 72 73 src_vreg_bob: src-vreg-bob-regulator { 74 compatible = "regulator-fixed"; 75 regulator-name = "src_vreg_bob"; 76 77 /* EC turns on with vbob_en; always on for AP */ 78 regulator-always-on; 79 regulator-boot-on; 80 regulator-min-microvolt = <3600000>; 81 regulator-max-microvolt = <3600000>; 82 83 vin-supply = <&ppvar_sys>; 84 }; 85 86 pp3300_dx_edp: pp3300-dx-edp-regulator { 87 compatible = "regulator-fixed"; 88 regulator-name = "pp3300_dx_edp"; 89 90 regulator-min-microvolt = <3300000>; 91 regulator-max-microvolt = <3300000>; 92 93 gpio = <&tlmm 43 GPIO_ACTIVE_HIGH>; 94 enable-active-high; 95 pinctrl-names = "default"; 96 pinctrl-0 = <&en_pp3300_dx_edp>; 97 }; 98 99 /* 100 * Apparently RPMh does not provide support for PM8998 S4 because it 101 * is always-on; model it as a fixed regulator. 102 */ 103 src_pp1800_s4a: pm8998-smps4 { 104 compatible = "regulator-fixed"; 105 regulator-name = "src_pp1800_s4a"; 106 107 regulator-min-microvolt = <1800000>; 108 regulator-max-microvolt = <1800000>; 109 110 regulator-always-on; 111 regulator-boot-on; 112 113 vin-supply = <&src_vph_pwr>; 114 }; 115 116 /* BOARD-SPECIFIC TOP LEVEL NODES */ 117 118 gpio-keys { 119 compatible = "gpio-keys"; 120 pinctrl-names = "default"; 121 pinctrl-0 = <&pen_eject_odl>; 122 123 pen-insert { 124 label = "Pen Insert"; 125 /* Insert = low, eject = high */ 126 gpios = <&tlmm 119 GPIO_ACTIVE_LOW>; 127 linux,code = <SW_PEN_INSERTED>; 128 linux,input-type = <EV_SW>; 129 wakeup-source; 130 }; 131 }; 132 133 panel: panel { 134 compatible ="innolux,p120zdg-bf1"; 135 power-supply = <&pp3300_dx_edp>; 136 backlight = <&backlight>; 137 no-hpd; 138 139 ports { 140 panel_in: port { 141 panel_in_edp: endpoint { 142 remote-endpoint = <&sn65dsi86_out>; 143 }; 144 }; 145 }; 146 }; 147}; 148 149/* 150 * Reserved memory changes 151 * 152 * Putting this all together (out of order with the rest of the file) to keep 153 * all modifications to the memory map (from sdm845.dtsi) in one place. 154 */ 155 156/* 157 * Our mpss_region is 8MB bigger than the default one and that conflicts 158 * with venus_mem and cdsp_mem. 159 * 160 * For venus_mem we'll delete and re-create at a different address. 161 * 162 * cdsp_mem isn't used on cheza right now so we won't bother re-creating it; but 163 * that also means we need to delete cdsp_pas. 164 */ 165/delete-node/ &venus_mem; 166/delete-node/ &cdsp_mem; 167/delete-node/ &cdsp_pas; 168 169/* Increase the size from 120 MB to 128 MB */ 170&mpss_region { 171 reg = <0 0x8e000000 0 0x8000000>; 172}; 173 174/* Increase the size from 2MB to 8MB */ 175&rmtfs_mem { 176 reg = <0 0x88f00000 0 0x800000>; 177}; 178 179/ { 180 reserved-memory { 181 venus_mem: memory@96000000 { 182 reg = <0 0x96000000 0 0x500000>; 183 no-map; 184 }; 185 }; 186}; 187 188&qspi { 189 status = "okay"; 190 pinctrl-names = "default"; 191 pinctrl-0 = <&qspi_clk &qspi_cs0 &qspi_data01>; 192 193 flash@0 { 194 compatible = "jedec,spi-nor"; 195 reg = <0>; 196 197 /* 198 * In theory chip supports up to 104 MHz and controller up 199 * to 80 MHz, but above 25 MHz wasn't reliable so we'll use 200 * that for now. b:117440651 201 */ 202 spi-max-frequency = <25000000>; 203 spi-tx-bus-width = <2>; 204 spi-rx-bus-width = <2>; 205 }; 206}; 207 208 209&apps_rsc { 210 pm8998-rpmh-regulators { 211 compatible = "qcom,pm8998-rpmh-regulators"; 212 qcom,pmic-id = "a"; 213 214 vdd-s1-supply = <&src_vph_pwr>; 215 vdd-s2-supply = <&src_vph_pwr>; 216 vdd-s3-supply = <&src_vph_pwr>; 217 vdd-s4-supply = <&src_vph_pwr>; 218 vdd-s5-supply = <&src_vph_pwr>; 219 vdd-s6-supply = <&src_vph_pwr>; 220 vdd-s7-supply = <&src_vph_pwr>; 221 vdd-s8-supply = <&src_vph_pwr>; 222 vdd-s9-supply = <&src_vph_pwr>; 223 vdd-s10-supply = <&src_vph_pwr>; 224 vdd-s11-supply = <&src_vph_pwr>; 225 vdd-s12-supply = <&src_vph_pwr>; 226 vdd-s13-supply = <&src_vph_pwr>; 227 vdd-l1-l27-supply = <&src_pp1025_s7a>; 228 vdd-l2-l8-l17-supply = <&src_pp1350_s3a>; 229 vdd-l3-l11-supply = <&src_pp1025_s7a>; 230 vdd-l4-l5-supply = <&src_pp1025_s7a>; 231 vdd-l6-supply = <&src_vph_pwr>; 232 vdd-l7-l12-l14-l15-supply = <&src_pp2040_s5a>; 233 vdd-l9-supply = <&src_pp2040_s5a>; 234 vdd-l10-l23-l25-supply = <&src_vreg_bob>; 235 vdd-l13-l19-l21-supply = <&src_vreg_bob>; 236 vdd-l16-l28-supply = <&src_vreg_bob>; 237 vdd-l18-l22-supply = <&src_vreg_bob>; 238 vdd-l20-l24-supply = <&src_vreg_bob>; 239 vdd-l26-supply = <&src_pp1350_s3a>; 240 vin-lvs-1-2-supply = <&src_pp1800_s4a>; 241 242 src_pp1125_s2a: smps2 { 243 regulator-min-microvolt = <1100000>; 244 regulator-max-microvolt = <1100000>; 245 }; 246 247 src_pp1350_s3a: smps3 { 248 regulator-min-microvolt = <1352000>; 249 regulator-max-microvolt = <1352000>; 250 }; 251 252 src_pp2040_s5a: smps5 { 253 regulator-min-microvolt = <1904000>; 254 regulator-max-microvolt = <2040000>; 255 }; 256 257 src_pp1025_s7a: smps7 { 258 regulator-min-microvolt = <900000>; 259 regulator-max-microvolt = <1028000>; 260 }; 261 262 vdd_qusb_hs0: 263 vdda_hp_pcie_core: 264 vdda_mipi_csi0_0p9: 265 vdda_mipi_csi1_0p9: 266 vdda_mipi_csi2_0p9: 267 vdda_mipi_dsi0_pll: 268 vdda_mipi_dsi1_pll: 269 vdda_qlink_lv: 270 vdda_qlink_lv_ck: 271 vdda_qrefs_0p875: 272 vdda_pcie_core: 273 vdda_pll_cc_ebi01: 274 vdda_pll_cc_ebi23: 275 vdda_sp_sensor: 276 vdda_ufs1_core: 277 vdda_ufs2_core: 278 vdda_usb1_ss_core: 279 vdda_usb2_ss_core: 280 src_pp875_l1a: ldo1 { 281 regulator-min-microvolt = <880000>; 282 regulator-max-microvolt = <880000>; 283 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 284 }; 285 286 vddpx_10: 287 src_pp1200_l2a: ldo2 { 288 regulator-min-microvolt = <1200000>; 289 regulator-max-microvolt = <1200000>; 290 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 291 292 /* TODO: why??? */ 293 regulator-always-on; 294 }; 295 296 pp1000_l3a_sdr845: ldo3 { 297 regulator-min-microvolt = <1000000>; 298 regulator-max-microvolt = <1000000>; 299 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 300 }; 301 302 vdd_wcss_cx: 303 vdd_wcss_mx: 304 vdda_wcss_pll: 305 src_pp800_l5a: ldo5 { 306 regulator-min-microvolt = <800000>; 307 regulator-max-microvolt = <800000>; 308 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 309 }; 310 311 vddpx_13: 312 src_pp1800_l6a: ldo6 { 313 regulator-min-microvolt = <1856000>; 314 regulator-max-microvolt = <1856000>; 315 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 316 }; 317 318 pp1800_l7a_wcn3990: ldo7 { 319 regulator-min-microvolt = <1800000>; 320 regulator-max-microvolt = <1800000>; 321 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 322 }; 323 324 src_pp1200_l8a: ldo8 { 325 regulator-min-microvolt = <1200000>; 326 regulator-max-microvolt = <1248000>; 327 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 328 }; 329 330 pp1800_dx_pen: 331 src_pp1800_l9a: ldo9 { 332 regulator-min-microvolt = <1800000>; 333 regulator-max-microvolt = <1800000>; 334 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 335 }; 336 337 src_pp1800_l10a: ldo10 { 338 regulator-min-microvolt = <1800000>; 339 regulator-max-microvolt = <1800000>; 340 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 341 }; 342 343 pp1000_l11a_sdr845: ldo11 { 344 regulator-min-microvolt = <1000000>; 345 regulator-max-microvolt = <1048000>; 346 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 347 }; 348 349 vdd_qfprom: 350 vdd_qfprom_sp: 351 vdda_apc1_cs_1p8: 352 vdda_gfx_cs_1p8: 353 vdda_qrefs_1p8: 354 vdda_qusb_hs0_1p8: 355 vddpx_11: 356 src_pp1800_l12a: ldo12 { 357 regulator-min-microvolt = <1800000>; 358 regulator-max-microvolt = <1800000>; 359 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 360 }; 361 362 vddpx_2: 363 src_pp2950_l13a: ldo13 { 364 regulator-min-microvolt = <1800000>; 365 regulator-max-microvolt = <2960000>; 366 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 367 }; 368 369 src_pp1800_l14a: ldo14 { 370 regulator-min-microvolt = <1800000>; 371 regulator-max-microvolt = <1800000>; 372 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 373 }; 374 375 src_pp1800_l15a: ldo15 { 376 regulator-min-microvolt = <1800000>; 377 regulator-max-microvolt = <1800000>; 378 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 379 }; 380 381 pp2700_l16a: ldo16 { 382 regulator-min-microvolt = <2704000>; 383 regulator-max-microvolt = <2704000>; 384 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 385 }; 386 387 src_pp1300_l17a: ldo17 { 388 regulator-min-microvolt = <1304000>; 389 regulator-max-microvolt = <1304000>; 390 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 391 }; 392 393 pp2700_l18a: ldo18 { 394 regulator-min-microvolt = <2704000>; 395 regulator-max-microvolt = <2960000>; 396 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 397 }; 398 399 /* 400 * NOTE: this rail should have been called 401 * src_pp3300_l19a in the schematic 402 */ 403 src_pp3000_l19a: ldo19 { 404 regulator-min-microvolt = <3304000>; 405 regulator-max-microvolt = <3304000>; 406 407 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 408 }; 409 410 src_pp2950_l20a: ldo20 { 411 regulator-min-microvolt = <2704000>; 412 regulator-max-microvolt = <2960000>; 413 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 414 }; 415 416 src_pp2950_l21a: ldo21 { 417 regulator-min-microvolt = <2704000>; 418 regulator-max-microvolt = <2960000>; 419 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 420 }; 421 422 pp3300_hub: 423 src_pp3300_l22a: ldo22 { 424 regulator-min-microvolt = <3304000>; 425 regulator-max-microvolt = <3304000>; 426 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 427 /* 428 * HACK: Should add a usb hub node and driver 429 * to turn this on and off at suspend/resume time 430 */ 431 regulator-boot-on; 432 regulator-always-on; 433 }; 434 435 pp3300_l23a_ch1_wcn3990: ldo23 { 436 regulator-min-microvolt = <3000000>; 437 regulator-max-microvolt = <3312000>; 438 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 439 }; 440 441 vdda_qusb_hs0_3p1: 442 src_pp3075_l24a: ldo24 { 443 regulator-min-microvolt = <3088000>; 444 regulator-max-microvolt = <3088000>; 445 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 446 }; 447 448 pp3300_l25a_ch0_wcn3990: ldo25 { 449 regulator-min-microvolt = <3304000>; 450 regulator-max-microvolt = <3304000>; 451 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 452 }; 453 454 pp1200_hub: 455 vdda_hp_pcie_1p2: 456 vdda_hv_ebi0: 457 vdda_hv_ebi1: 458 vdda_hv_ebi2: 459 vdda_hv_ebi3: 460 vdda_mipi_csi_1p25: 461 vdda_mipi_dsi0_1p2: 462 vdda_mipi_dsi1_1p2: 463 vdda_pcie_1p2: 464 vdda_ufs1_1p2: 465 vdda_ufs2_1p2: 466 vdda_usb1_ss_1p2: 467 vdda_usb2_ss_1p2: 468 src_pp1200_l26a: ldo26 { 469 regulator-min-microvolt = <1200000>; 470 regulator-max-microvolt = <1200000>; 471 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 472 }; 473 474 pp3300_dx_pen: 475 src_pp3300_l28a: ldo28 { 476 regulator-min-microvolt = <3304000>; 477 regulator-max-microvolt = <3304000>; 478 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 479 }; 480 481 src_pp1800_lvs1: lvs1 { 482 regulator-min-microvolt = <1800000>; 483 regulator-max-microvolt = <1800000>; 484 }; 485 486 src_pp1800_lvs2: lvs2 { 487 regulator-min-microvolt = <1800000>; 488 regulator-max-microvolt = <1800000>; 489 }; 490 }; 491 492 pm8005-rpmh-regulators { 493 compatible = "qcom,pm8005-rpmh-regulators"; 494 qcom,pmic-id = "c"; 495 496 vdd-s1-supply = <&src_vph_pwr>; 497 vdd-s2-supply = <&src_vph_pwr>; 498 vdd-s3-supply = <&src_vph_pwr>; 499 vdd-s4-supply = <&src_vph_pwr>; 500 501 src_pp600_s3c: smps3 { 502 regulator-min-microvolt = <600000>; 503 regulator-max-microvolt = <600000>; 504 }; 505 }; 506}; 507 508&dsi0 { 509 status = "okay"; 510 vdda-supply = <&vdda_mipi_dsi0_1p2>; 511 512 ports { 513 port@1 { 514 endpoint { 515 remote-endpoint = <&sn65dsi86_in>; 516 data-lanes = <0 1 2 3>; 517 }; 518 }; 519 }; 520}; 521 522&dsi0_phy { 523 status = "okay"; 524 vdds-supply = <&vdda_mipi_dsi0_pll>; 525}; 526 527edp_brij_i2c: &i2c3 { 528 status = "okay"; 529 clock-frequency = <400000>; 530 531 sn65dsi86_bridge: bridge@2d { 532 compatible = "ti,sn65dsi86"; 533 reg = <0x2d>; 534 pinctrl-names = "default"; 535 pinctrl-0 = <&edp_brij_en &edp_brij_irq>; 536 537 interrupt-parent = <&tlmm>; 538 interrupts = <10 IRQ_TYPE_LEVEL_HIGH>; 539 540 enable-gpios = <&tlmm 102 GPIO_ACTIVE_HIGH>; 541 542 vpll-supply = <&src_pp1800_s4a>; 543 vccio-supply = <&src_pp1800_s4a>; 544 vcca-supply = <&src_pp1200_l2a>; 545 vcc-supply = <&src_pp1200_l2a>; 546 547 clocks = <&rpmhcc RPMH_LN_BB_CLK2>; 548 clock-names = "refclk"; 549 550 ports { 551 #address-cells = <1>; 552 #size-cells = <0>; 553 554 port@0 { 555 reg = <0>; 556 sn65dsi86_in: endpoint { 557 remote-endpoint = <&dsi0_out>; 558 }; 559 }; 560 561 port@1 { 562 reg = <1>; 563 sn65dsi86_out: endpoint { 564 remote-endpoint = <&panel_in_edp>; 565 }; 566 }; 567 }; 568 }; 569}; 570 571ap_pen_1v8: &i2c11 { 572 status = "okay"; 573 clock-frequency = <400000>; 574 575 digitizer@9 { 576 compatible = "wacom,w9013", "hid-over-i2c"; 577 reg = <0x9>; 578 pinctrl-names = "default"; 579 pinctrl-0 = <&pen_irq_l>, <&pen_pdct_l>, <&pen_rst_l>; 580 581 vdd-supply = <&pp3300_dx_pen>; 582 vddl-supply = <&pp1800_dx_pen>; 583 post-power-on-delay-ms = <100>; 584 585 interrupt-parent = <&tlmm>; 586 interrupts = <24 IRQ_TYPE_LEVEL_LOW>; 587 588 hid-descr-addr = <0x1>; 589 }; 590}; 591 592amp_i2c: &i2c12 { 593 status = "okay"; 594 clock-frequency = <400000>; 595}; 596 597ap_ts_i2c: &i2c14 { 598 status = "okay"; 599 clock-frequency = <400000>; 600 601 touchscreen@10 { 602 compatible = "elan,ekth3500"; 603 reg = <0x10>; 604 pinctrl-names = "default"; 605 pinctrl-0 = <&ts_int_l &ts_reset_l>; 606 607 interrupt-parent = <&tlmm>; 608 interrupts = <125 IRQ_TYPE_LEVEL_LOW>; 609 610 vcc33-supply = <&src_pp3300_l28a>; 611 612 reset-gpios = <&tlmm 118 GPIO_ACTIVE_LOW>; 613 }; 614}; 615 616&lpasscc { 617 status = "okay"; 618}; 619 620&mdss { 621 status = "okay"; 622}; 623 624&mdss_mdp { 625 status = "okay"; 626}; 627 628&qupv3_id_0 { 629 status = "okay"; 630}; 631 632&qupv3_id_1 { 633 status = "okay"; 634}; 635 636&sdhc_2 { 637 status = "okay"; 638 639 pinctrl-names = "default"; 640 pinctrl-0 = <&sdc2_clk &sdc2_cmd &sdc2_data &sd_cd_odl>; 641 642 vmmc-supply = <&src_pp2950_l21a>; 643 vqmmc-supply = <&vddpx_2>; 644 645 cd-gpios = <&tlmm 44 GPIO_ACTIVE_LOW>; 646}; 647 648&spi0 { 649 status = "okay"; 650}; 651 652&spi10 { 653 status = "okay"; 654 655 cros_ec: ec@0 { 656 compatible = "google,cros-ec-spi"; 657 reg = <0>; 658 interrupt-parent = <&tlmm>; 659 interrupts = <122 IRQ_TYPE_LEVEL_LOW>; 660 pinctrl-names = "default"; 661 pinctrl-0 = <&ec_ap_int_l>; 662 spi-max-frequency = <3000000>; 663 664 cros_ec_pwm: ec-pwm { 665 compatible = "google,cros-ec-pwm"; 666 #pwm-cells = <1>; 667 }; 668 669 i2c_tunnel: i2c-tunnel { 670 compatible = "google,cros-ec-i2c-tunnel"; 671 google,remote-bus = <0>; 672 #address-cells = <1>; 673 #size-cells = <0>; 674 }; 675 676 pdupdate { 677 compatible = "google,cros-ec-pd-update"; 678 }; 679 }; 680}; 681 682#include <arm/cros-ec-keyboard.dtsi> 683#include <arm/cros-ec-sbs.dtsi> 684 685&uart6 { 686 status = "okay"; 687 688 bluetooth: wcn3990-bt { 689 compatible = "qcom,wcn3990-bt"; 690 vddio-supply = <&src_pp1800_s4a>; 691 vddxo-supply = <&pp1800_l7a_wcn3990>; 692 vddrf-supply = <&src_pp1300_l17a>; 693 vddch0-supply = <&pp3300_l25a_ch0_wcn3990>; 694 max-speed = <3200000>; 695 }; 696}; 697 698&uart9 { 699 status = "okay"; 700}; 701 702&ufs_mem_hc { 703 status = "okay"; 704 pinctrl-names = "init", "default"; 705 pinctrl-0 = <&ufs_dev_reset_assert>; 706 pinctrl-1 = <&ufs_dev_reset_deassert>; 707 708 vcc-supply = <&src_pp2950_l20a>; 709 vcc-max-microamp = <600000>; 710}; 711 712&ufs_mem_phy { 713 status = "okay"; 714 715 vdda-phy-supply = <&vdda_ufs1_core>; 716 vdda-pll-supply = <&vdda_ufs1_1p2>; 717}; 718 719&usb_1 { 720 status = "okay"; 721 722 /* We'll use this as USB 2.0 only */ 723 qcom,select-utmi-as-pipe-clk; 724}; 725 726&usb_1_dwc3 { 727 /* 728 * The hardware design intends this port to be hooked up in peripheral 729 * mode, so we'll hardcode it here. Some details: 730 * - SDM845 expects only a single Type C connector so it has only one 731 * native Type C port but cheza has two Type C connectors. 732 * - The only source of DP is the single native Type C port. 733 * - On cheza we want to be able to hook DP up to _either_ of the 734 * two Type C connectors and want to be able to achieve 4 lanes of DP. 735 * - When you configure a Type C port for 4 lanes of DP you lose USB3. 736 * - In order to make everything work, the native Type C port is always 737 * configured as 4-lanes DP so it's always available. 738 * - The extra USB3 port on SDM845 goes to a USB 3 hub which is then 739 * sent to the two Type C connectors. 740 * - The extra USB2 lines from the native Type C port are always 741 * setup as "peripheral" so that we can mux them over to one connector 742 * or the other if someone needs the connector configured as a gadget 743 * (but they only get USB2 speeds). 744 * 745 * All the hardware muxes would allow us to hook things up in different 746 * ways to some potential benefit for static configurations (you could 747 * achieve extra USB2 bandwidth by using two different ports for the 748 * two conenctors or possibly even get USB3 peripheral mode), but in 749 * each case you end up forcing to disconnect/reconnect an in-use 750 * USB session in some cases depending on what you hotplug into the 751 * other connector. Thus hardcoding this as peripheral makes sense. 752 */ 753 dr_mode = "peripheral"; 754 755 /* 756 * We always need the high speed pins as 4-lanes DP in case someone 757 * hotplugs a DP peripheral. Thus limit this port to a max of high 758 * speed. 759 */ 760 maximum-speed = "high-speed"; 761 762 /* 763 * We don't need the usb3-phy since we run in highspeed mode always, so 764 * re-define these properties removing the superspeed USB PHY reference. 765 */ 766 phys = <&usb_1_hsphy>; 767 phy-names = "usb2-phy"; 768}; 769 770&usb_1_hsphy { 771 status = "okay"; 772 773 vdd-supply = <&vdda_usb1_ss_core>; 774 vdda-pll-supply = <&vdda_qusb_hs0_1p8>; 775 vdda-phy-dpdm-supply = <&vdda_qusb_hs0_3p1>; 776 777 qcom,imp-res-offset-value = <8>; 778 qcom,hstx-trim-value = <QUSB2_V2_HSTX_TRIM_21_6_MA>; 779 qcom,preemphasis-level = <QUSB2_V2_PREEMPHASIS_5_PERCENT>; 780 qcom,preemphasis-width = <QUSB2_V2_PREEMPHASIS_WIDTH_HALF_BIT>; 781}; 782 783&usb_2 { 784 status = "okay"; 785}; 786 787&usb_2_dwc3 { 788 /* We have this hooked up to a hub and we always use in host mode */ 789 dr_mode = "host"; 790}; 791 792&usb_2_hsphy { 793 status = "okay"; 794 795 vdd-supply = <&vdda_usb2_ss_core>; 796 vdda-pll-supply = <&vdda_qusb_hs0_1p8>; 797 vdda-phy-dpdm-supply = <&vdda_qusb_hs0_3p1>; 798 799 qcom,imp-res-offset-value = <8>; 800 qcom,hstx-trim-value = <QUSB2_V2_HSTX_TRIM_22_8_MA>; 801}; 802 803&usb_2_qmpphy { 804 status = "okay"; 805 806 vdda-phy-supply = <&vdda_usb2_ss_1p2>; 807 vdda-pll-supply = <&vdda_usb2_ss_core>; 808}; 809 810&wifi { 811 status = "okay"; 812 813 vdd-0.8-cx-mx-supply = <&src_pp800_l5a >; 814 vdd-1.8-xo-supply = <&pp1800_l7a_wcn3990>; 815 vdd-1.3-rfa-supply = <&src_pp1300_l17a>; 816 vdd-3.3-ch0-supply = <&pp3300_l25a_ch0_wcn3990>; 817}; 818 819/* PINCTRL - additions to nodes defined in sdm845.dtsi */ 820 821&qspi_cs0 { 822 pinconf { 823 pins = "gpio90"; 824 bias-disable; 825 }; 826}; 827 828&qspi_clk { 829 pinconf { 830 pins = "gpio95"; 831 bias-disable; 832 }; 833}; 834 835&qspi_data01 { 836 pinconf { 837 pins = "gpio91", "gpio92"; 838 839 /* High-Z when no transfers; nice to park the lines */ 840 bias-pull-up; 841 }; 842}; 843 844&qup_i2c3_default { 845 pinconf { 846 pins = "gpio41", "gpio42"; 847 drive-strength = <2>; 848 849 /* Has external pullup */ 850 bias-disable; 851 }; 852}; 853 854&qup_i2c11_default { 855 pinconf { 856 pins = "gpio31", "gpio32"; 857 drive-strength = <2>; 858 859 /* Has external pullup */ 860 bias-disable; 861 }; 862}; 863 864&qup_i2c12_default { 865 pinconf { 866 pins = "gpio49", "gpio50"; 867 drive-strength = <2>; 868 869 /* Has external pullup */ 870 bias-disable; 871 }; 872}; 873 874&qup_i2c14_default { 875 pinconf { 876 pins = "gpio33", "gpio34"; 877 drive-strength = <2>; 878 879 /* Has external pullup */ 880 bias-disable; 881 }; 882}; 883 884&qup_spi0_default { 885 pinconf { 886 pins = "gpio0", "gpio1", "gpio2", "gpio3"; 887 drive-strength = <2>; 888 bias-disable; 889 }; 890}; 891 892&qup_spi5_default { 893 pinconf { 894 pins = "gpio85", "gpio86", "gpio87", "gpio88"; 895 drive-strength = <2>; 896 bias-disable; 897 }; 898}; 899 900&qup_spi10_default { 901 pinconf { 902 pins = "gpio53", "gpio54", "gpio55", "gpio56"; 903 drive-strength = <2>; 904 bias-disable; 905 }; 906}; 907 908&qup_uart6_default { 909 /* Change pinmux to all 4 pins since CTS and RTS are connected */ 910 pinmux { 911 pins = "gpio45", "gpio46", 912 "gpio47", "gpio48"; 913 }; 914 915 pinconf-cts { 916 /* 917 * Configure a pull-down on 45 (CTS) to match the pull of 918 * the Bluetooth module. 919 */ 920 pins = "gpio45"; 921 bias-pull-down; 922 }; 923 924 pinconf-rts-tx { 925 /* We'll drive 46 (RTS) and 47 (TX), so no pull */ 926 pins = "gpio46", "gpio47"; 927 drive-strength = <2>; 928 bias-disable; 929 }; 930 931 pinconf-rx { 932 /* 933 * Configure a pull-up on 48 (RX). This is needed to avoid 934 * garbage data when the TX pin of the Bluetooth module is 935 * in tri-state (module powered off or not driving the 936 * signal yet). 937 */ 938 pins = "gpio48"; 939 bias-pull-up; 940 }; 941}; 942 943&qup_uart9_default { 944 pinconf-tx { 945 pins = "gpio4"; 946 drive-strength = <2>; 947 bias-disable; 948 }; 949 950 pinconf-rx { 951 pins = "gpio5"; 952 drive-strength = <2>; 953 bias-pull-up; 954 }; 955}; 956 957/* PINCTRL - board-specific pinctrl */ 958&pm8005_gpio { 959 gpio-line-names = "", 960 "", 961 "SLB", 962 ""; 963}; 964 965&pm8998_adc { 966 adc-chan@ADC5_AMUX_THM1_100K_PU { 967 reg = <ADC5_AMUX_THM1_100K_PU>; 968 label = "sdm_temp"; 969 }; 970 971 adc-chan@ADC5_AMUX_THM2_100K_PU { 972 reg = <ADC5_AMUX_THM2_100K_PU>; 973 label = "quiet_temp"; 974 }; 975 976 adc-chan@ADC5_AMUX_THM3_100K_PU { 977 reg = <ADC5_AMUX_THM3_100K_PU>; 978 label = "lte_temp_1"; 979 }; 980 981 adc-chan@ADC5_AMUX_THM4_100K_PU { 982 reg = <ADC5_AMUX_THM4_100K_PU>; 983 label = "lte_temp_2"; 984 }; 985 986 adc-chan@ADC5_AMUX_THM5_100K_PU { 987 reg = <ADC5_AMUX_THM5_100K_PU>; 988 label = "charger_temp"; 989 }; 990}; 991 992&pm8998_gpio { 993 gpio-line-names = "", 994 "", 995 "SW_CTRL", 996 "", 997 "", 998 "", 999 "", 1000 "", 1001 "", 1002 "", 1003 "", 1004 "", 1005 "", 1006 "", 1007 "", 1008 "", 1009 "", 1010 "", 1011 "", 1012 "", 1013 "", 1014 "CFG_OPT1", 1015 "WCSS_PWR_REQ", 1016 "", 1017 "CFG_OPT2", 1018 "SLB"; 1019}; 1020 1021&tlmm { 1022 /* 1023 * pinctrl settings for pins that have no real owners. 1024 */ 1025 pinctrl-names = "default", "sleep"; 1026 pinctrl-0 = <&bios_flash_wp_r_l>, 1027 <&ap_suspend_l_deassert>; 1028 1029 pinctrl-1 = <&bios_flash_wp_r_l>, 1030 <&ap_suspend_l_assert>; 1031 1032 /* 1033 * Hogs prevent usermode from changing the value. A GPIO can be both 1034 * here and in the pinctrl section. 1035 */ 1036 ap-suspend-l-hog { 1037 gpio-hog; 1038 gpios = <126 GPIO_ACTIVE_LOW>; 1039 output-low; 1040 }; 1041 1042 ap_edp_bklten: ap-edp-bklten { 1043 pinmux { 1044 pins = "gpio37"; 1045 function = "gpio"; 1046 }; 1047 1048 pinconf { 1049 pins = "gpio37"; 1050 drive-strength = <2>; 1051 bias-disable; 1052 }; 1053 }; 1054 1055 bios_flash_wp_r_l: bios-flash-wp-r-l { 1056 pinmux { 1057 pins = "gpio128"; 1058 function = "gpio"; 1059 input-enable; 1060 }; 1061 1062 pinconf { 1063 pins = "gpio128"; 1064 bias-disable; 1065 }; 1066 }; 1067 1068 ec_ap_int_l: ec-ap-int-l { 1069 pinmux { 1070 pins = "gpio122"; 1071 function = "gpio"; 1072 input-enable; 1073 }; 1074 1075 pinconf { 1076 pins = "gpio122"; 1077 bias-pull-up; 1078 }; 1079 }; 1080 1081 edp_brij_en: edp-brij-en { 1082 pinmux { 1083 pins = "gpio102"; 1084 function = "gpio"; 1085 }; 1086 1087 pinconf { 1088 pins = "gpio102"; 1089 drive-strength = <2>; 1090 bias-disable; 1091 }; 1092 }; 1093 1094 edp_brij_irq: edp-brij-irq { 1095 pinmux { 1096 pins = "gpio10"; 1097 function = "gpio"; 1098 }; 1099 1100 pinconf { 1101 pins = "gpio10"; 1102 drive-strength = <2>; 1103 bias-pull-down; 1104 }; 1105 }; 1106 1107 en_pp3300_dx_edp: en-pp3300-dx-edp { 1108 pinmux { 1109 pins = "gpio43"; 1110 function = "gpio"; 1111 }; 1112 1113 pinconf { 1114 pins = "gpio43"; 1115 drive-strength = <2>; 1116 bias-disable; 1117 }; 1118 }; 1119 1120 h1_ap_int_odl: h1-ap-int-odl { 1121 pinmux { 1122 pins = "gpio129"; 1123 function = "gpio"; 1124 input-enable; 1125 }; 1126 1127 pinconf { 1128 pins = "gpio129"; 1129 bias-pull-up; 1130 }; 1131 }; 1132 1133 pen_eject_odl: pen-eject-odl { 1134 pinmux { 1135 pins = "gpio119"; 1136 function = "gpio"; 1137 bias-pull-up; 1138 }; 1139 }; 1140 1141 pen_irq_l: pen-irq-l { 1142 pinmux { 1143 pins = "gpio24"; 1144 function = "gpio"; 1145 }; 1146 1147 pinconf { 1148 pins = "gpio24"; 1149 1150 /* Has external pullup */ 1151 bias-disable; 1152 }; 1153 }; 1154 1155 pen_pdct_l: pen-pdct-l { 1156 pinmux { 1157 pins = "gpio63"; 1158 function = "gpio"; 1159 }; 1160 1161 pinconf { 1162 pins = "gpio63"; 1163 1164 /* Has external pullup */ 1165 bias-disable; 1166 }; 1167 }; 1168 1169 pen_rst_l: pen-rst-l { 1170 pinmux { 1171 pins = "gpio23"; 1172 function = "gpio"; 1173 }; 1174 1175 pinconf { 1176 pins = "gpio23"; 1177 bias-disable; 1178 drive-strength = <2>; 1179 1180 /* 1181 * The pen driver doesn't currently support 1182 * driving this reset line. By specifying 1183 * output-high here we're relying on the fact 1184 * that this pin has a default pulldown at boot 1185 * (which makes sure the pen was in reset if it 1186 * was powered) and then we set it high here to 1187 * take it out of reset. Better would be if the 1188 * pen driver could control this and we could 1189 * remove "output-high" here. 1190 */ 1191 output-high; 1192 }; 1193 }; 1194 1195 sdc2_clk: sdc2-clk { 1196 pinconf { 1197 pins = "sdc2_clk"; 1198 bias-disable; 1199 1200 /* 1201 * It seems that mmc_test reports errors if drive 1202 * strength is not 16. 1203 */ 1204 drive-strength = <16>; 1205 }; 1206 }; 1207 1208 sdc2_cmd: sdc2-cmd { 1209 pinconf { 1210 pins = "sdc2_cmd"; 1211 bias-pull-up; 1212 drive-strength = <16>; 1213 }; 1214 }; 1215 1216 sdc2_data: sdc2-data { 1217 pinconf { 1218 pins = "sdc2_data"; 1219 bias-pull-up; 1220 drive-strength = <16>; 1221 }; 1222 }; 1223 1224 sd_cd_odl: sd-cd-odl { 1225 pinmux { 1226 pins = "gpio44"; 1227 function = "gpio"; 1228 }; 1229 1230 pinconf { 1231 pins = "gpio44"; 1232 bias-pull-up; 1233 }; 1234 }; 1235 1236 ts_int_l: ts-int-l { 1237 pinmux { 1238 pins = "gpio125"; 1239 function = "gpio"; 1240 }; 1241 1242 pinconf { 1243 pins = "gpio125"; 1244 bias-pull-up; 1245 }; 1246 }; 1247 1248 ts_reset_l: ts-reset-l { 1249 pinmux { 1250 pins = "gpio118"; 1251 function = "gpio"; 1252 }; 1253 1254 pinconf { 1255 pins = "gpio118"; 1256 bias-disable; 1257 drive-strength = <2>; 1258 }; 1259 }; 1260 1261 ufs_dev_reset_assert: ufs_dev_reset_assert { 1262 config { 1263 pins = "ufs_reset"; 1264 bias-pull-down; /* default: pull down */ 1265 /* 1266 * UFS_RESET driver strengths are having 1267 * different values/steps compared to typical 1268 * GPIO drive strengths. 1269 * 1270 * Following table clarifies: 1271 * 1272 * HDRV value | UFS_RESET | Typical GPIO 1273 * (dec) | (mA) | (mA) 1274 * 0 | 0.8 | 2 1275 * 1 | 1.55 | 4 1276 * 2 | 2.35 | 6 1277 * 3 | 3.1 | 8 1278 * 4 | 3.9 | 10 1279 * 5 | 4.65 | 12 1280 * 6 | 5.4 | 14 1281 * 7 | 6.15 | 16 1282 * 1283 * POR value for UFS_RESET HDRV is 3 which means 1284 * 3.1mA and we want to use that. Hence just 1285 * specify 8mA to "drive-strength" binding and 1286 * that should result into writing 3 to HDRV 1287 * field. 1288 */ 1289 drive-strength = <8>; /* default: 3.1 mA */ 1290 output-low; /* active low reset */ 1291 }; 1292 }; 1293 1294 ufs_dev_reset_deassert: ufs_dev_reset_deassert { 1295 config { 1296 pins = "ufs_reset"; 1297 bias-pull-down; /* default: pull down */ 1298 /* 1299 * default: 3.1 mA 1300 * check comments under ufs_dev_reset_assert 1301 */ 1302 drive-strength = <8>; 1303 output-high; /* active low reset */ 1304 }; 1305 }; 1306 1307 ap_suspend_l_assert: ap_suspend_l_assert { 1308 config { 1309 pins = "gpio126"; 1310 function = "gpio"; 1311 bias-no-pull; 1312 drive-strength = <2>; 1313 output-low; 1314 }; 1315 }; 1316 1317 ap_suspend_l_deassert: ap_suspend_l_deassert { 1318 config { 1319 pins = "gpio126"; 1320 function = "gpio"; 1321 bias-no-pull; 1322 drive-strength = <2>; 1323 output-high; 1324 }; 1325 }; 1326}; 1327